DeWalt DW0811LR Manuel utilisateur

E

ES

F

PT

Please read these instructions before operating the product.

www.DEWALT.com

DW089LR, DW089LG 3 x 360° Line Laser

DW0811LR, DW0811LG 2 x 360° Line Laser

2

Figures

A

B

3

C

D E

4

Figures

F

3

1

2

4

5 6

7

DW089LR/LG

5

G

I

3

4

5

1

2

1

2

1

5/8-11

1/4-20

6

H

J

6

Figures

a

b

a

c

a

b

a

b

> 30 . (9m)

_

c

b

1

2

3

K

7

ab

ba

> 30 . (9m)

_

b

c

ba

c

a

c

1

2

3

L

8

Figures

g

h

e

f

d

c

d

c

a

b

c

g

b

a

2

h

d

> 8 . (2.5m)

_

M

1

2

3

9

90˚

a

f

b

c

a

f

c

bc

e

> 14. (4m)

_

> 14. (4m)

_

> 14. (4m)

_

b

N

1

2

3

10

E

Contents

• Laser Information

• User Safety

• Battery Safety

• Powering the Laser

• Operating Tips

• Turning the Laser ON

• Checking Laser Accuracy

• Using the Laser

• Troubleshooting

• Accessories

• Service and Repairs

• Warranty

• Speciﬁ cations

Laser Information

The DW089LR/DW089LG 3-Beam 360° Line Laser and

the DW0811LR/DW0811LG 2-Beam 360° Line Laser

are Class 2 laser products. The lasers are self-leveling

laser tools that can be used for horizontal (level) and

vertical (plumb) alignment projects.

Each product complies with 21 CFR 1040.10 and

1040.11 except for deviations pursuant to laser notice

No. 50, dated June 24, 2007.

Conforms to UL STDS 61010-1 & 2595

Certified to CSA STD C22.2 No. 61010-1

Supplier’s Declaration of Conformity

47 CFR § 2.1077 Compliance Information

Unique Identiﬁ er: DW089LR, DW089LG, DW0811LR,

DW0811LG

Responsible Party – U.S. Contact Information

D

EWALT

701 East Joppa Road

Towson, Maryland 21286

www.DEWALT.com

FCC Compliance Statement

This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful

interference in a residential installation. This equipment

generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance

with the instructions, may cause harmful interference

to radio communications. However, there is no

guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful

interference to radio and television reception, which can

be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by

one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV

technician for help.

ISED Compliance Statement

This device contains license-exempt transmitter(s)/

receiver(s) that comply with Innovation, Science, and

Economic Development Canada's license-exempt

RSS(s). Operation is subject to the following two

conditions:

1. This device may not cause interference.

2. This device must accept any interference, including

interference that may cause undesired operation of

the device.

11

E

User Safety

Safety Guidelines

The deﬁ nitions below describe the level of severity for

each signal word. Please read the manual and pay

attention to these symbols.

DANGER: Indicates an imminently hazardous

situation which, if not avoided, will result in

death or serious injury.

WARNING: Indicates a potentially hazardous

situation which, if not avoided, could result in

death or serious injury.

CAUTION: Indicates a potentially hazardous

situation which, if not avoided, may result in

minor or moderate injury.

NOTICE: Indicates a practice not related to personal

injury which, if not avoided, may result in property

damage.

If you have any questions or comments about

this or any D

EWALT tool,

call 1-800-4-DEWALT (1-800-433-9258)

or go to www.DEWALT.com.

WARNING:

Never modify the tool or any part of it. Damage

to the laser or personal injury could result.

WARNING:

Read and understand all instructions.

Failure to follow the warnings and instructions

may result in electric shock, ﬁ re and/or serious

injury.

SAVE THESE INSTRUCTIONS

WARNING:

Laser Radiation Exposure. Do not

disassemble or modify the laser level.

There are no user serviceable parts inside.

Serious eye injury could result.

WARNING:

Hazardous Radiation. Use of controls or

adjustments or performance of procedures

other than those speciﬁ ed herein may result in

hazardous radiation exposure.

The label on your laser may include the following

symbols.

Symbol Meaning

V Volts

mW Milliwatts

Laser Warning

nm Wavelength in nanometers

2 Class 2 Laser

Warning Labels

For your convenience and safety, the following labels

are on your laser.

WARNING: To reduce the risk of injury,

user must read instruction manual.

WARNING: LASER RADIATION. DO

NOT STARE INTO BEAM. Class 2 Laser

Product.

≤1.5mW @ 630-680nm

IEC 60825-1: 2014

5002595

≤1.5mW @ 510-530nm

IEC 60825-1: 2014

5002595

≤1.5mW @ 630-680nm

IEC 60825-1: 2014

5002595

≤1.5mW @ 510-530nm

IEC 60825-1: 2014

• If the equipment is used in a manner not

speciﬁ ed by the manufacturer, the protection

provided by the equipment may be impaired.

12

E

• Do not operate the laser in explosive

atmospheres, such as in the presence of

ﬂ ammable liquids, gases, or dust. This tool may

create sparks which may ignite the dust or fumes.

• Store an idle laser out of reach of children and

other untrained persons. Lasers are dangerous in

the hands of untrained users.

• Tool service MUST be performed by qualiﬁ ed

repair personnel. Service or maintenance performed

by unqualiﬁ ed personnel may result in injury. To

locate your nearest DEWALT service center go to

www.DEWALT.com.

• Do not use optical tools such as a telescope or

transit to view the laser beam. Serious eye injury

could result.

• Do not place the laser in a position which may

cause anyone to intentionally or unintentionally

stare into the laser beam. Serious eye injury could

result.

• Do not position the laser near a reﬂ ective

surface which may reﬂ ect the laser beam toward

anyone’s eyes. Serious eye injury could result.

• Turn the laser off when it is not in use. Leaving

the laser on increases the risk of staring into the

laser beam.

• Do not modify the laser in any way. Modifying the

tool may result in hazardous laser radiation exposure.

• Do not operate the laser around children or allow

children to operate the laser. Serious eye injury

may result.

• Do not remove or deface warning labels. If labels

are removed, the user or others may inadvertently

expose themselves to radiation.

• Position the laser securely on a level surface. If

the laser falls, damage to the laser or serious injury

could result.

Personal Safety

• Stay alert, watch what you are doing, and use

common sense when operating the laser. Do not use

the laser when you are tired or under the inﬂ uence

of drugs, alcohol, or medication. A moment of

inattention while operating the laser may result in

serious personal injury.

• Use personal protective equipment. Always wear

eye protection. Depending on the work conditions,

wearing protective equipment such as a dust

mask, non-skid safety shoes, hard hat, and hearing

protection will reduce personal injury.

Tool Use and Care

• Do not use the laser if the Power/Transport Lock

switch does not turn the laser on or off. Any tool that

cannot be controlled with the switch is dangerous and

must be repaired.

• Follow instructions in the Maintenance section of

this manual. Use of unauthorized parts or failure to

follow Maintenance instructions may create a risk of

electric shock or injury.

Battery Safety

WARNING:

Batteries can explode, or leak, and can

cause injury or ﬁ re. To reduce this risk:

• Carefully follow all instructions and warnings on the

battery label and package, and the accompanying

Battery Safety manual.

• Always insert batteries correctly with regard to

polarity + and –, as marked on the battery and the

equipment.

• Do not short battery terminals.

• Do not charge disposable batteries.

• Do not mix old and new batteries. Replace all

batteries at the same time with new batteries of the

same brand and type.

13

E

• Remove dead batteries immediately and dispose of

per local codes.

• Do not dispose of batteries in ﬁ re.

• Keep batteries out of reach of children.

• Remove batteries when the device is not in use.

• Use only the charger speciﬁ ed for your rechargeable

battery pack.

• Disconnect the battery pack from the laser before

making any adjustments, changing accessories, or

storing the laser. Such preventative safety measures

reduce the risk of starting the laser accidentally.

• When the battery pack is not in use, keep it away

from other metal objects, like paper clips, coins,

keys, nails, screws, or other small metal objects that

can make a connection from one terminal to another.

Shorting the battery terminals together may cause

burns or a ﬁ re.

• Use the laser only with speciﬁ cally designated

battery packs. Use of other battery packs may create

a risk of injury and ﬁ re.

• Under abusive conditions, liquid may be ejected from

the battery; avoid contact. If contact accidentally

occurs, ﬂ ush with water. If liquid contacts eyes,

additionally seek medical help. Liquid ejected from

the battery may cause irritation or burns.

• Do not use a battery pack or laser that is damaged or

modiﬁ ed. Damaged or modiﬁ ed batteries may exhibit

unpredictable behavior resulting in ﬁ re, explosion, or

risk of injury.

• Do not expose a battery pack or laser to ﬁ re

or excessive temperature. Exposure to ﬁ re or

temperature above 265° F (130° C) may cause an

explosion.

• Follow all the charging instructions and do not charge

the battery pack outside of the temperature range

speciﬁ ed in the instructions. Charging improperly or

at temperatures outside of the speciﬁ ed range may

damage the battery and increase the risk of ﬁ re.

Powering the Laser

This laser can be powered by either of these battery

packs:

• A DEWALT 12V MAX* Li-ion Battery Pack

(DCB120, DCB122, DCB123, DCB125, or DCB127).

*Maximum initial battery voltage (measured without a

workload) is 12 volts. Nominal voltage is 10.8.

• A DEWALT AA Starter Pack with 4 new high-quality

name brand AA batteries. Note: The AA Starter Pack

is only recommended for use with the red laser

(DW089LR or DW0811LR).

Use of any other batteries may create a risk of ﬁ re.

Charging the Li-ion Battery

1.

If the DEWALT 12V MAX* Li-ion battery pack is

attached to the laser, remove it.

• Rotate the laser so it is easier to access the

battery pack (Figure

C

1

).

• While pressing down on the release button on the

battery pack (Figure

C

2

), pull the battery pack

up to unlock it from the laser.

• Pull the battery pack the rest of the way up and

out of the laser (Figure

C

3

).

2.

Plug the charger cord into an electrical outlet.

3.

Slide the battery pack into the charger until it snaps

in place (Figure

B

1

). On the charger, the left

indicator light will flash to let you know the battery is

being charged.

4.

After the battery is fully-charged (the indicator light

on the charger no longer flashes), press and hold

the release button on the battery pack (Figure

B

2

) and slide the pack out of the charger

(Figure

B

3

).

5.

Slide the battery pack down in the laser until it

snaps in place (Figure

B

4

).

14

E

Installing New AA Batteries

CAUTION:

The AA Starter Pack is designed speciﬁ cally

for use with DEWALT 12V compatible laser

products and cannot be used with any other

tools. Do not attempt to modify the product.

1.

If the AA Starter Pack is attached to the laser,

remove it.

• Rotate the laser so it is easier to access the

Starter Pack (Figure

C

1

).

• While pressing down on the release button on the

Starter Pack (Figure

C

2

), pull the Starter Pack

up to unlock it from the laser).

• Pull the Starter Pack the rest of the way up and

out of the laser (Figure

C

3

).

2.

On the AA Starter Pack, lift up the latch to open the

battery compartment cover (Figure

A

1

and

A

2

).

3.

Insert four new, high-quality, name brand AA

batteries, making sure to position the - and +

ends of each battery as noted inside the battery

compartment (Figure

A

3

).

4.

Push the battery compartment cover down until it

snaps in place (Figure

A

4

).

5.

Slide the Starter Pack down in the laser until it

snaps in place (Figure

A

5

).

Viewing the Battery Meter

When the laser is ON, the battery meter on the keypad

(Figure

F

7

) indicates how much power remains.

Each of the four LEDs on the battery meter represents

25% of the power.

• The bottom LED will illuminate and ﬂ ash when the

battery level is low (below 12.5%). The laser may

continue to operate for a short time while the battery

power continues to drain, but the beam(s) will quickly

dim.

• After fresh batteries are installed in the AA Starter

Pack, or the 12V MAX Li-ion battery is charged, and

the laser is turned ON again, the laser beam(s) will

return to full brightness and the battery indicator level

will indicate full capacity.

• If all 4 LEDs on the battery meter remain ON, this

indicates that the laser is not fully powered OFF.

When the laser is not in use, make sure the Power/

Transport Lock switch is placed to the LEFT to the

Locked/OFF position (Figure

F

2

).

Operating Tips

• To extend battery life per charge, turn the laser off

when it is not in use.

• To ensure the accuracy of your work, check the

laser calibration often. Refer to Checking Laser

Accuracy.

• Before attempting to use the laser, make sure it is

positioned securely, on a smooth, ﬂ at stable surface

that is level in both directions.

• To increase beam visibility, use a Laser Target Card

(Figure

D

) and/or wear Laser Enhancement Glass es

(Figure

E

) to help find the beam.

CAUTION:

To reduce the risk of serious injury, never stare

directly into the laser beam with or without

these glasses. Refer to Accessories for

important information.

• Always mark the center of the beam created by the

laser.

• Extreme temperature changes can cause movement

or shifting of building structures, metal tripods,

equipment, etc., which can effect accuracy. Check

your accuracy often while working.

• If the laser has been dropped, check to make sure

your laser is still calibrated. Refer to Checking Laser

Accuracy.

15

E

Turning the Laser On

Place the laser on a ﬂ at level surface. Slide the Power/

Transport Lock switch

F

2

to the right to unlock/turn

ON the laser.

Each laser line is powered on by pressing its button on

the keypad (Figure

F

3

). Pressing the button again

turns the laser line off. The laser lines can be powered

one at a time or all at the same time.

Laser Buttons

DW089LR/LG

Horizontal laser line

(Figure

F

4

)

Side vertical laser line

(Figure

F

5

)

Front vertical laser line

(Figure

F

6

)

DW0811LR/LG Horizontal laser line

(Figure

F

4

)

Side vertical laser line

(Figure

F

5

)

When the laser is not in use, slide the Power/Transport

Lock switch to the left in the OFF/Locked position. If

the Power/Transport Lock switch is not placed in the

lock position, all 4 LEDs will continuously ﬂ ash on the

Battery Meter.

Checking Laser Accuracy

The laser tools are sealed and calibrated at the factory.

It is recommended that you perform an accuracy check

prior to using the laser for the ﬁ rst time (in case the

laser was exposed to extreme temperatures) and then

regularly to ensure the accuracy of your work. When

performing any of the accuracy checks listed in this

manual, follow these guidelines:

• Use the largest area/distance possible, closest to the

operating distance. The greater the area/distance,

the easier to measure the accuracy of the laser.

• Place the laser on a smooth, ﬂ at, stable surface that

is level in both directions.

• Mark the center of the laser beam.

Horizontal Beam - Scan Direction

Checking the horizontal scan calibration of the laser

requires two walls 30′ (9m) apart. It is important to

conduct a calibration check using a distance no shorter

than the distance of the applications for which the tool

will be used.

1.

Place the laser against the end of the wall on a

smooth, ﬂ at, stable surface that is level in both

directions (Figure

K

1

).

2.

Move the Power/Transport Lock switch to the right

to turn the laser ON.

3.

Press to turn on the horizontal beam.

4.

At least 30′ (9m) apart along the laser beam, mark

a

and

b

.

5.

Turn the laser 180º.

6.

Adjust the height of the laser so the center of the

beam is aligned with

a

(Figure

K

2

).

7.

Directly above or below

b

, mark

c

along the laser

beam (Figure

K

3

).

8.

Measure the vertical distance between

b

and

c

.

9.

If your measurement is greater than the Allowable

Distance Between

b

and

c

for the

corresponding Distance Between Walls in the

following table, the laser must be serviced at an

authorized service center.

Distance

Between Walls

Allowable Distance

Between

b

and

c

30’ (9m) 1/4” (6.0mm)

40’ (12m) 5/16” (8.0mm)

50’ (15m) 13/32” (10.0mm)

16

E

Horizontal Beam - Pitch Direction

Checking the horizontal pitch calibration of the

laser requires a single wall at least 30′ (9m) long.

It is important to conduct a calibration check using

a distance no shorter than the distance of the

applications for which the tool will be used.

1.

Place the laser against the end of the wall on a

smooth, ﬂ at, stable surface that is level in both

directions (Figure

L

1

).

2.

Move the Power/Transport Lock switch to the right

to turn the laser ON.

3.

Press to turn on the horizontal beam.

4.

At least 30′ (9m) apart along the laser beam, mark

a

and

b

.

5.

Move the laser to the opposite end of the wall

(Figure

L

2

).

6.

Position the laser toward the ﬁ rst end of the same

wall and parallel to the adjacent wall.

7.

Adjust the height of the laser so the center of the

beam is aligned with

b

.

8.

Directly above or below

a

, mark

c

along the laser

beam (Figure

L

3

).

9.

Measure the distance between

a

and

c

.

10.

If your measurement is greater than the Allowable

Distance Between

a

and

c

for the correspond-

ing Distance Between Walls in the following table,

the laser must be serviced at an authorized service

center.

Distance

Between Walls

Allowable Distance

Between

a

and

c

30’ (9m) 1/4” (6.0mm)

40’ (12m) 5/16” (8.0mm)

50’ (15m) 13/32” (10.0mm)

Vertical Beam (DW089)

Checking the vertical (plumb) calibration of the

laser can be most accurately done when there is a

substantial amount of vertical height available, ideally

30’ (9m), with one person on the ﬂ oor positioning

the laser and another person near a ceiling to mark

the position of the beam. It is important to conduct a

calibration check using a distance no shorter than the

distance of the applications for which the tool will be

used.

1.

Place the laser on a smooth, ﬂ at, stable surface

that is level in both directions (Figure

M

1

).

2.

Move the Power/Transport Lock switch to the right

to turn the laser ON.

3.

Press and to turn on both vertical beams.

4.

Mark two short lines where the beams cross

a

,

b

and also on the ceiling

c

,

d

. Always mark

the center of the beam's thickness (Figure

M

2

).

5.

Pick up and rotate the laser 180º, and position it

so the beams line up with the marked lines on the

level surface (

e

,

f

) (Figure

M

3

).

6.

Mark two short lines where the beams cross on the

ceiling

g

,

h

.

7.

Measure the distance between each set of marked

lines on the ceiling (

c

,

g

and

d

,

h

). If the mea-

surement is greater than the values shown below,

the laser must be serviced at an authorized service

center.

Ceiling Height

Allowable Distance

Between Marks

8’ (2.5m) 1/16” (1.5mm)

10’ (3m) 3/32” (2.0mm)

14’ (4m) 1/8” (2.5mm)

20’ (6m) 5/32’ (4mm)

30’ (9m) 1/4’ (6mm)

17

E

90º Accuracy Between Vertical Beams

(DW089)

Checking 90º accuracy requires an open ﬂ oor area at

least 33’ x 18’ (10m x 5m). Refer to Figure

N

for the

position of the laser at each step and for the location of

the marks made at each step. Always mark the center

of the beam's thickness.

1.

Place the laser on a smooth, ﬂ at, stable surface

that is level in both directions.

2.

Move the Power/Transport Lock switch to the right

to turn the laser ON.

3.

Press to turn on the side vertical beam.

4.

Mark the center of the beam at three locations

(

a

,

b

,

c

) on the ﬂ oor along the side laser line.

Mark

b

should be at the midpoint of the laser line

(Figure

N

1

).

5.

Pick up and move the laser to

b

.

6.

Press to turn on the front vertical beam too

(Figure

N

2

).

7.

Position the front vertical beam so it crosses

precisely at

b

, with the side beam aligned with

c

(Figure

N

2

).

8.

Mark a location

e

along the front vertical beam at

least 14’ (4m) away from the unit (Figure

N

2

).

9.

Rotate the laser 90º so the side vertical beam now

passes through

b

and

e

(Figure

N

3

).

10.

Directly above or below

a

, mark

f

along the front

vertical beam.

11.

Measure the distance between

a

and

f

. If the

measurement is greater than the values shown

below, the laser must be serviced at an authorized

service center.

Distance from

a

to

b

Allowable Distance

Between

a

and

f

14’ (4m) 5/32” (3.5mm)

17’ (5m) 3/16” (4.5mm)

20’ (6m) 7/32” (5.5mm)

23’ (7m) 1/4” (6mm)

Using the Laser

Leveling the Laser

As long as the laser is properly calibrated, the laser is

self-leveling. Each laser is calibrated at the factory to

ﬁ nd level as long as it is positioned on a ﬂ at surface

within average ± 4° of level. No manual adjustments

are required.

If the laser has been tilted so much that it cannot

self-level (> 4°), the laser beam will ﬂ ash. There are

two ﬂ ashing sequences associated with the out of level

condition.

• Between 4° and 10° the beams ﬂ ash with a constant

blink cycle

• At angles greater than 10° the beams ﬂ ash with a

three blink cycle.

When the beams ﬂ ash THE LASER IS NOT LEVEL

(OR PLUMB) AND SHOULD NOT BE USED FOR

DETERMINING OR MARKING LEVEL OR PLUMB.

Try repositioning the laser on a more level surface.

18

E

Using the Pivot Bracket

The laser has a magnetic pivot bracket (Figure

G

1

)

permanently attached to the unit.

WARNING:

Position the laser and/or wall mount on

a stable surface. Serious personal injury or

damage to the laser may result if the laser

falls.

• The bracket has magnets (Figure

H

2

) which allow

the unit to be mounted to most upright surfaces

made of steel or iron. Common examples of suitable

surfaces include steel framing studs, steel door

frames, and structural steel beams.

• The bracket has a keyhole slot (Figure

G

2

or

H

1

) so it can be hung from a nail or screw on any

kind of surface.

Maintenance

• To maintain the accuracy of your work, check the

laser often to make sure it is properly calibrated.

See Field Calibration Check.

• Calibration checks and other maintenance repairs

may be performed by D

EWALT service centers.

• When not in use, store the laser in the kit box

provided. Do not store your laser at temperatures

below -5˚F (-20˚C ) or above 140˚F (60˚C).

• Do not store your laser in the kit box if the laser is

wet. The laser should be dried ﬁ rst with a soft dry

cloth prior to storage.

Cleaning

Exterior plastic parts may be cleaned with a damp cloth.

Although these parts are solvent resistant, NEVER use

solvents. Use a soft, dry cloth to remove moisture from

the tool before storage.

Troubleshooting

The Laser Does Not Turn On

• Make sure AA batteries (when used) are installed

correctly according to + and – on the inside of the

battery door.

• Make sure the batteries or rechargeable pack are

in proper working condition. If in doubt, try installing

new batteries.

• Make sure that the battery contacts are clean and

free of rust or corrosion. Be sure to keep the laser

level dry and use only new, high-quality, name brand

batteries to reduce the chance of battery leakage.

• If the laser unit is heated above 120˚F (50˚C), the

unit will not turn on. If the laser has been stored in

extremely hot temperatures, allow it to cool. The

laser level will not be damaged by pressing the on/

off button before cooling to its proper operating

temperature.

The Laser Beams Flash

The lasers are designed to self-level up to an average

of 4° in all directions If the laser is tilted so much that

the internal mechanism cannot level itself, the laser

beams will ﬂ ash indicating that the tilt range has been

exceeded. THE FLASHING BEAMS CREATED BY THE

LASER ARE NOT LEVEL OR PLUMB AND SHOULD

NOT BE USED FOR DETERMINING OR MARKING

LEVEL OR PLUMB. Try repositioning the laser on a

more level surface.

The Laser Beams Will Not Stop Moving

The laser is a precision instrument. Therefore, if it is

not positioned on a stable (and motionless) surface,

the laser will continue to try to ﬁ nd level. If the beam

will not stop moving, try placing the laser on a more

stable surface. Also, try to make sure that the surface is

relatively ﬂ at, so that the laser is stable.

19

E

The Battery Meter LEDs Flash

When all 4 LEDs continuously ﬂ ash on the Battery

Meter this indicates that the unit has not been fully

powered off using the Power/Transport Lock switch

(Figure

F

2

). The Power/Transport Lock switch

should always be placed in the LOCKED/OFF position

when the laser is not in use.

Accessories

The laser is equipped with both 1/4 - 20 and 5/8 - 11

female threads (I) on the bottom of the unit (Figure

I

).

This thread is to accommodate current or future DEWalt

accessories. Only use DEWalt accessories speciﬁ ed

for use with this product. Follow the directions included

with the accessory.

WARNING:

Since accessories, other than those offered

by DEWalt, have not been tested with this

product, use of such accessories with this

tool could be hazardous. To reduce the risk of

injury, only DEWalt recommended accessories

should be used with this product.

If you need any assistance in locating any accessory,

please contact your nearest D

EWALT service center or

go to www.DEWALT.com.

Target Card

Some laser kits include a Laser Target Card (Figure

D

)

to aid in locating and marking the laser beam. The

target card enhances the visibility of the laser beam as

the beam crosses over the card. The card is marked

with standard and metric scales. The laser beam

passes through the red plastic and reflects off of the

reflective tape on the reverse side. The magnet at the

top of the card is designed to hold the target card to

ceiling track or steel studs to determine plumb and level

positions. For best performance when using the Target

Card, the DEWALT logo should be facing you.

Laser Enhancement Glasses

Some laser kits include Laser En hancement Glasses

(Figure

E

). These glasses improve the visibility of

the laser beam under bright light conditions or over

long distances when the laser is used for interior

applications. These glasses are not required to operate

the laser.

CAUTION:

These glasses are not ANSI approved

safety glasses and should not be used while

operating other tools. These glasses do not

keep the laser beam from entering your eyes.

CAUTION:

To reduce the risk of serious injury, never stare

directly into the laser beam with or without

these glasses.

Ceiling Mount

The laser ceiling mount (Figure

J

1

), if included, offers

more mounting options for the laser. The ceiling mount

has a clamp (Figure

J

2

) at one end which can be ﬁ xed

to a wall angle for acoustic ceiling installation (Figure

J

3

). At each end of the ceiling mount is a screw hole

(Figure

J

4

and

J

5

), allowing the ceiling mount to

be attached to any surface with a nail or screw.

Once the ceiling mount is secured, its steel plate

provides a surface to which the magnetic pivot bracket

(Figure

J

6

) can be attached. The position of the

laser can then be ﬁ ne-tuned by sliding the magnetic

pivot bracket up or down on the wall mount.

20

E

Service and Repairs

NOTE: Disassembling the laser level(s) will void all

warranties on the product.

To assure product SAFETY and RELIABILITY, repairs,

maintenance and adjustment should be performed by

authorized service centers. Service or maintenance

performed by unqualiﬁ ed personnel may result in a risk

of injury. To locate your nearest D

EWalt service center

call 1-800-4-DEWALT (1-800-433-9258) or go to www.

DEWALT.com.

Warranty

Go to www.DEWALT.com for the latest warranty

information.

La page charge ...

DeWalt DW0811LR Manuel utilisateur

Ce manuel convient également à

DeWalt DW0811LR Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents