Shark UV490CCO Manuel utilisateur
- Catégorie
- Aspirateurs
- Taper
- Manuel utilisateur
UV490CCO
Owner’s Guide
Manuel du
propriétaire
WWW.SHARKCLEAN.COM
2 TOLL FREE: 1-800-798-7398
WARNING:
To reduce the risk of
electric shock or injury, do not use
outdoors or on wet surfaces.
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK OR INJURY:
GENERAL ELECTRICAL SAFETY:
1. Unplug from electrical outlet when not in use
and before servicing.
2. DO NOT use vacuum with a damaged cord
or plug. If appliance is not working as it
should, has been dropped, damaged, left
outdoors, or dropped into water, return it to
SharkNinja Operating LLC for examination,
repair, or adjustment.
3. DO NOT pull or carry vacuum by the cord.
4. DO NOT unplug by pulling on cord; to
unplug, grasp the plug, not the cord.
5. DO NOT handle plug or appliance with
wet hands.
6. DO NOT run the vacuum over the power
cord.
7. DO NOT use the cord as a handle.
8. DO NOT close a door on the cord.
9. DO NOT pull cord around sharp corners.
The use of an extension cord is not
recommended.
10. DO NOT leave appliance when plugged in.
11. Keep cord away from heated surfaces.
12. Turn off all controls before plugging or
unplugging vacuum cleaner.
13. Always turn off this appliance before
connecting or disconnecting motorized
nozzle.
14. Store your appliance with the power cord
secured around the two cord holders-as
shown in the storage instructions.
IMPORTANT SAFETY INSTRUCTIONS
For Household Use Only
WHEN USING AN ELECTRICAL
APPLIANCE, BASIC SAFETY PRECAUTIONS
SHOULD ALWAYS BE OBSERVED,
INCLUDING THE FOLLOWING:
READ ALL INSTRUCTIONS BEFORE USING
YOUR SHARK
®
NAVIGATOR
®
LIFT-AWAY
™
DELUXE.
POLARIZED PLUG:
To reduce the risk of electric shock, this appliance
has a polarized plug (one blade is wider than the
other). As a safety feature, this plug will fit into
a polarized outlet only one way. If the plug does
not fit fully into the outlet, reverse the plug. If it
still does not fit, contact a qualified electrician.
DO NOT force into outlet or try to
modify to fit.
3www.sharkclean.com
HOSE ATTACHMENTS:
1. DO NOT use if air flow is restricted; if the air
paths, the hose, or the accessories become
blocked, turn the vacuum cleaner off. Remove
all obstructions before you turn on the
unit again.
2. Keep the end of the hose and accessory
openings away from face and body.
3. Keep cleaning tools and hose suction
openings away from hair, face, fingers,
uncovered feet, or loose clothing.
4. Only use manufacturer’s recommended
attachments.
GENERAL USE:
1. Use only as described in this manual.
2. DO NOT put any objects into openings. DO
NOT use with any opening blocked; keep
free of dust, lint, hair, and anything that may
reduce air flow.
3. Keep your work area well lit.
4. Keep the vacuum moving over the carpet
surface at all times to avoid damaging the
carpet fibers.
5. DO NOT place vacuum on unstable surfaces
such as chairs or tables.
6. DO NOT allow young children to operate
the vacuum or use as a toy. Close attention is
necessary when used by or near children.
7. DO NOT use vacuum cleaner if it has
been dropped, damaged, left outdoors, or
submerged in water. Return to SharkNinja
Operating LLC for examination, repair, or
adjustment.
8. DO NOT use without dust cup and/or filters
in place.
English
SAVE THESE INSTRUCTIONS
DUST CUP/FILTERS/ACCESSORIES:
Before turning on the vacuum:
1. Make sure that all filters are thoroughly dry
after routine cleaning.
2. Make sure that dust cup and all filters are in
place after routine maintenance.
3. Make sure accessories are free of blockages.
4. Only use filters and accessories provided by
SharkNinja Operating LLC. [Failure to do so
will void the warranty.]
GENERAL CLEANING:
1. DO NOT pick up large-sized objects.
2. DO NOT pick up hard or sharp objects such
as glass, nails, screws or coins that could
damage the vacuum cleaner.
3. DO NOT pick up smoking or burning objects
such as hot coals, cigarette butts, fireplace
ash or matches.
4. DO NOT use to pick up drywall dust.
5. DO NOT pick up flammable or combustible
materials such as lighter fluid, gasoline, or
kerosene or use vacuum in areas where they
may be present.
6. DO NOT pick up toxic solutions such as
chlorine bleach, ammonia, or drain cleaner.
7. DO NOT use in an enclosed space where
vapours are present from paint, paint thinner,
moth-proofing substances, flammable dust or
other explosive or toxic materials.
8. DO NOT vacuum up any liquids.
9. DO NOT immerse vacuum cleaner in water or
other liquids.
10. DO NOT use outdoors or on wet surfaces;
use only on dry surfaces.
11. Use extra care when cleaning on stairs.
4 TOLL FREE: 1-800-798-7398
This manual covers model number:
UV490CCO 26
TECHNICAL SPECIFICATIONS
Voltage: 120V., 60Hz
Watts: 1200W
Amps: 10A
5www.sharkclean.com
English
English
Getting Started 6
Mode 1: Upright Vac 8
Mode 2: Portable Lift-Away
™
10
Above-Floor Cleaning 11
Storage 12
Maintenance 13
Emptying the Dust Cup 13
Cleaning the Pre-Motor Filters 13
Cleaning the Post-Motor HEPA Filter 14
Cleaning the Pet Power Brush 14
Cleaning the Motorized Floor Brush 14
Checking for Blockages 15
Troubleshooting Guide 16
Ordering Parts 17
Warranty and Product Registration 34
Contents
Thank you for
purchasing
the Shark
®
Navigator
®
Lift-Away
™
Deluxe.
6 TOLL FREE: 1-800-798-7398
FIRST THING’S FIRST, YOU NEED TO KNOW
WHAT’S IN THE BOX YOU JUST OPENED:
a Handle with Stretch Hose
b Accessory Holder
c Extension Wand
d Portable Lift-Away
™
e Motorized Floor Brush
f Dusting Brush
g Crevice Tool
h Power Brush
i Extension Wand
j Appliance Wand
ACCESSORIES:
CREVICE TOOL
Reach deep into narrow spaces and clean between
cushions, under radiators and baseboards and in
hard to reach crevices and corners. (Fig. 1)
DUSTING BRUSH
Dust shelves, lamp shades, window blinds, books,
furniture and other upholstered household items.
(Fig. 2)
POWER BRUSH
This unique tool was engineered for fast and
easy removal of pet hair and ground in dirt from
carpeted stairs and upholstery. (Fig. 3)
ACCESSORY HOLDER
Designed to hold the crevice tool and dusting brush.
For quick access to tools when vacuuming and
cleaning around the house. (Fig. 4)
EXTENSION WAND
Reach even further and attach the crevice tool, the
dusting brush or the power brush for cleaning all
around the house. (Fig. 5)
APPLIANCE WAND
Extend to access hard-to-reach areas under hard-
to-move appliances and furniture. Flip extension
upside down to clean underside of appliances also.
(Fig. 6)
Getting Started
Fig. 1
Fig. 3 Fig. 4
Fig. 2
Fig. 5
Fig. 6
f
a
e
c
d
b
g
i i
h
7www.sharkclean.com
English
English
Your new Shark Navigator
®
Lift-Away
™
Deluxe vacuum cleaner can easily be configured into
different cleaning modes to meet all your cleaning needs: upright vacuum and portable
Lift-Away
™
- both with constant suction power.
MODES:
1 UPRIGHT VAC
Upright vacuuming - floors and carpets. (Fig. 6)
Fig. 6
Fig. 7
2 PORTABLE Lift-Away
™
Take the Lift-Away
™
with you around the house to
clean hard to reach places. (Fig. 7)
8 TOLL FREE: 1-800-798-7398
To reduce the risk of electric shock, unplug the unit before assembling, adding or removing attachments or
converting modes.
WARNING: The On/Off switch is on the top of the Lift-Away
™
canister. Always ensure the power is OFF
(“O” position) before plugging and unplugging.
TO ASSEMBLE:
1 Place the floor nozzle on a level surface.
2 Align the tube of the floor nozzle with the tube on
the Lift-Away
™
canister and lower until you hear
the two pieces click into place. (Fig. 8)
When attaching the motorized floor brush, ensure
that the latching mechanism is fully locked in place
to ensure electrical connection has been made.
3 Attach the end of the extension wand to the tube
on the back of the Lift-Away
™
canister until it
clicks into place. (Fig. 9)
4 Slide the accessory holder (a) positioned opposite
the upper cord wrap, over the extension wand.
Align the tab with the groove and push down.
(Fig. 10)
5 Push the handle (b) onto the top of the extension
wand until you hear it click into place. (Fig. 10)
6 Insert the end of the stretch hose (c) into the
connector on the back of the Lift-Away
™
canister. (Fig. 10)
7 Store the dusting brush (d) and the crevice tool (e)
on the mounts of the accessory holder. (Fig. 10)
Fig. 8
Fig. 9
Fig. 10
Mode 1: Upright Vac
c
Upper Cord
Storage Wrap
a
d
e
b
9www.sharkclean.com
English
English
TO USE:
1 Rotate the cord release to quickly release the
power cord.
2 Secure the power cord in the cord hook.
= Brush Roll ON
= Bare Floor
= OFF
3 Press the On/Off switch (a) to the “I” position to
vacuum bare floors (straight suction only) or to the
“II” position to engage the motorized floor brush
(for vacuuming carpets and rugs). (Fig. 11)
IMPORTANT: The motorized brush indicator light
(b) will illuminate green when motorized floor
brush is on, or red if there is a blockage or jam.
(Fig. 11) This feature is designed to protect your
Lifetime Belt that powers your motorized floor
brush. See Checking for Blockages on page 15.
4 Gently press the floor nozzle down with your foot
while you grasp the handle and tilt it back towards
you. (Fig. 12)
NOTE: The rotating brush on the motorized
floor brush will not spin unless the nozzle is flat
against the floor and the handle is tilted back.
5 Due to the huge suction power of this
vacuum, it may become necessary at
times to adjust the suction release (c) on
the handle. (Fig. 11) If the vacuum seems
difficult to push or pull or if it is lifting
up area rugs, adjust the suction release
by rotating the collar 90° counterclockwise
to open the valve. Rotate the collar
clockwise to close the valve when you need
high suction and for vacuuming floors.
6 Empty dust cup after vacuuming and periodically
during use when it appears full. (See
“Maintenance” section for instructions.)
7 When you are finished vacuuming, turn the
vacuum off.
Fig. 12
Fig. 11
Release suction
for easier push
and pull on high pile
carpets and area
rugs.
b
a
Suction
Release Collar
c
10 TOLL FREE: 1-800-798-7398
a
You can carry your vacuum cleaner
in both modes by the carry handle
located on top of the dust cup.
Fig. 15
Fig. 14
Fig. 13
Mode 2: Portable Lift-Away
™
b
a
PORTABLE LIFT-AWAY
™
1 Separate the portable Lift-Away
™
canister from
the floor nozzle by pressing the red release
button (a) on the side of the canister. Gently
hold the nozzle to the floor with your foot and
pull the canister up. (Fig. 13)
2 Press the handle release button (a) and pull the
handle up or press the extension wand release
button (b) and pull the extension wand up.
(Fig. 14)
3 Attach desired accessory onto the end of either
the extension wand or the ha
ndle.
4 Press the On/Off switch to the “I” position to
turn the vacuum on for above-floor cleaning and
hold the handle in one hand while you carry the
portable Lift-Away
™
around the house with the
other hand. (Fig. 15)
11www.sharkclean.com
English
English
Fig. 16
Suction
Release Collar
a
Above-Floor Cleaning
CLEAN ABOVE THE FLOOR IN UPRIGHT VAC OR
PORTABLE LIFT-AWAY
™
MODE
1 Press the handle release button and pull the
handle up or press the extension wand release
button and pull the extension wand up.
2 Attach desired accessory onto the end of either the
extension wand or the handle. (Fig. 16)
3 Your vacuum has tremendous suction
power. Adjust the amount of suction with
the suction release on the handle. Open
the valve (a) by rotating the collar 90˚
counterclockwise for low suction when
doing light jobs such as drapes or fine
surfaces. Close the valve (a) by rotating the
collar clockwise 90˚ for high suction and
when using the hand held power brush.
(Fig. 16)
4 Press the On/Off switch to the “I” position to turn
the vacuum on for above-floor cleaning.
IMPORTANT: Ensure vacuum is in upright
position. Do not use position “II” when cleaning
above the floor in the upright vac mode as this
will engage the motorized floor brush. The
rotating brush may damage your floor if run for a
prolonged period of time in one area.
Release suction when
dusting delicate objects,
furniture or draperies.
12 TOLL FREE: 1-800-798-7398
Fig. 17
Quick
Cord Release
Lower Cord
Storage Clip
Storage and Maintenance
STORE YOUR VACUUM SAFELY
1 Convert your vacuum back to upright vac mode.
2 Rotate the upper quick cord release to its upright
position and coil the power cord loosely around
the two clips. Clip the plug onto the cord to secure.
(Fig. 17)
3 Store the dusting brush and the crevice tool on the
mounts on the accessory holder.
4 Store your vacuum cleaner safely in a cool dry area
where it will not be a hazard, will not get damaged
and will not cause damage to anyone or anything.
NOTE: Empty dust cup after cleaning and prior
to storing. (See “Maintenance” section for
instructions.)
To reduce the risk of electric shock, unplug the unit
before performing any cleaning, maintenance, or
troubleshooting checks.
Reassemble all parts securely before operating
vacuum.
DO NOT operate the vacuum without the filters
and dust cup in place.
DO NOT operate the vacuum with WET filters.
IMPORTANT: Make sure all filters are completely
dry before inserting back into vacuum.
WARNING: Never insert sharp objects into any
opening to clear an obstruction.
IMPORTANT: Damages caused while clearing
or attempting to clear blockages are not covered
under your product’s limited warranty.
13www.sharkclean.com
English
English
IMPORTANT: Loss of Suction
may occur if foam filters are not
cleaned every 3 months. Rinse and
allow to air dry completely. Also, tap
loose dirt off filter between washes as
needed. Foam filters may appear dirty
after use - this is normal.
Fig. 18
Fig. 19
COMPONENT
MAINTENANCE SCHEDULE
Rinse and air dry every 3 months under normal use.
Empty each time you vacuum.
Pre-Motor Foam Filter
Dust Cup
Rinse and air dry every 3 months under normal use.
Pre-Motor Felt Filter
Clean once every 2 years or as needed.
Post-Motor HEPA Filter
1
2
3
4
CLEANING THE PRE-MOTOR FILTERS
1 Remove the dust cup.
2 Pull the 2 filters out from the top of the motor
base. (Fig. 21)
3 Rinse the filters thoroughly in lukewarm water until
the water runs clear.
DO NOT put the filter in the washing machine or
dishwasher.
NOTE: The material in the filter will discolour
over time. This is NORMAL and will not affect the
performance of the filter.
4 Squeeze out excess water and let air-dry for at
least 24 hours before replacing. Do not use a hair
dryer or other heating methods to dry.
5 Place the felt filter in first, then the foam filter.
6 Replace the dust cup.
EMPTYING THE DUST CUP
The dust cup needs to be emptied each time you
vacuum and periodically during cleaning, when the
dust cup appears full.
1 Undo the latches on the sides of the dust cup by
lifting them up and outwards to remove the dust
cup from the motor base. (Fig. 18)
2 Hold the dust cup over a trash receptacle and
press the bottom door release button. (Fig. 19)
Tap gently to empty contents. Press the door shut
again until it clicks.
3 If needed, turn the dust cup upside down over the
trash receptacle and press the top door release
button. (Fig. 20) Tap gently to remove contents.
Use a dry cloth or paper towel to remove debris
stuck to the screen filter inside the dust cup. Press
the door shut again until it clicks.
4 Replace the dust cup on top of the motor base.
Hook the two latches onto the tabs on the sides of
the dust cup and push down to lock.
Screen
Filter
Fig. 20
Fig. 21
Pre-Motor
Foam Filter
Felt Filter
Post Motor
HEPA Filter
Maintenance
14 TOLL FREE: 1-800-798-7398
CLEANING THE POWER BRUSH
1 Slide the locking latch (a) forward and gently tilt
brush housing upward to open. (Fig. 25)
IMPORTANT: DO NOT force; it will not open all
the way.
2 Carefully remove any blockage or debris.
3 Turn the power brush over to inspect the rotating
brush and cut away any build-up of hair or string
wrapped around the rotating bristle brush with
scissors. (Fig. 26)
4 Push the housing back down and slide the locking
latch backward to lock.
Fig. 23
Fig. 22
Fig. 24
CLEANING THE POST-MOTOR HEPA FILTER
1 Remove the filter cover from the front of the
vacuum by pulling up on the tab and pulling the
cover away from the vacuum. (Fig. 22)
2 Take out the HEPA filter by pulling it straight out.
3 Turn the filter over so that the dirty side is on
the bottom and vigorously tap it clean against a
garbage can to remove any dust. (Fig. 23)
4 Wash the filter under the tap using lukewarm
water with the dirty side face down until the water
runs clear. (Fig. 24)
DO NOT put the filter in the washing machine or
dishwasher.
NOTE: The material in the filter will discolour
over time. This is NORMAL and will not affect the
performance of the filter.
5 Allow the filter to air dry for 24 hours. Do not use a
hair dryer or other heating methods to dry.
6 Once the HEPA filter is dry, replace it back into the
vacuum.
7 Replace the cover by inserting the two tabs into
the holes at the top and then swinging the cover
down until it clicks into place.
Fig. 26
Fig. 25
CLEANING THE MOTORIZED FLOOR BRUSH
When your motorized floor brush needs cleaning or
locks onto an object, it automatically shuts down to
prevent damage to your lifetime belt. The indicator
light will illuminate red warning you to turn off the
vacuum and clear blockage immediately. The light will
reset itself once blockage has been cleared and power
has been cycled on/off or vacuum has been locked in
the upright position.
1 Detach the motorized floor brush from the portable
Lift-Away
™
canister.
2 Inspect the opening underneath and the rotating
brush. If a build-up of debris is present, remove it.
Carefully cut anything wound around the rotating
brush with scissors. Avoid damaging or cutting the
bristles. (Fig. 27)
Maintenance - cont’d
Rotating
Brush
Fig. 27
15www.sharkclean.com
English
English
CHECKING FOR BLOCKAGES
Blockages may cause your vacuum to overheat and
shut down. To prevent this from happening, check
potential blockage areas after heavy use or if you
detect a loss of suction or poor cleaning performance.
1 Dust Cup
Dust cup may be full. Empty dust cup.
2 Pre-Motor and Post-Motor Filters
• Pre-motor filters require washing every 3
months for optimum performance.
The post-motor HEPA filter needs to be washed
every 2 years.
• Ensure that all the filters are clean.
3 Accessories
• Check intake openings:
- Extension Wands
- Dusting Brush
- Crevice Tool
- Power Brush
4 Hose and Connections to Vacuum
• Detach the stretch hose from the back of the
portable Lift-Away
™
canister by squeezing
the tabs together and pulling up. (Fig. 28)
Straighten out the hose and look inside for
blockages.
• Remove the dust cup and extension wand and
separate the portable Lift-Away
™
canister
from the motorized floor brush. Look in all 4
openings for any blockages. (Fig. 29)
5 Motorized Floor Brush
(Side suction models)
• Detach the hose on the motorized floor brush
at the top by squeezing the tabs together and
pulling out, and at the bottom by pulling out
the connector. Inspect inside the 3 holes.
(Fig. 30)
Make sure you are working in a well
lit area and use a flashlight to help
search for blockages.
Fig. 30
Fig. 29
Fig. 28
16 TOLL FREE: 1-800-798-7398
PROBLEM POSSIBLE REASONS AND SOLUTIONS
Vacuum is not picking
up dirt.
Check filters to see if they need cleaning. Follow instructions for rinsing
and drying the filters before re-inserting back into the vacuum. (See
“Maintenance” sections for instructions.)
Dust cup may be full; empty dust cup.
Check hose and hose connections for blockages; clear blockages if required.
If dust cup is empty, and attachment inlets are clear, check for other
blockages. (See “Checking for Blockages” for instructions.)
Vacuum lifts scatter rugs
(lightweight, movable
rugs).
Suction is powerful. Take care when vacuuming scatter-type rugs or rugs
with delicately sewn edges. Open the suction release on the handle to
decrease suction power.
Move the On/Off switch to “I - Suction Only” position to disengage the
brush roll.
Airflow is restricted. No
suction or light suction.
Check filters to see if they need cleaning. Follow instructions for rinsing and
drying the filters before re-inserting back into the vacuum.
Dust cup may be full; empty dust cup.
Check hose, hose connections, nozzles and accessories for blockages; clear
blockages if required.
Close the suction release on the handle to increase suction power.
If dust cup is empty, and attachment inlets are clear, check for other
blockages.
Brush roll does not spin.
Immediately turn off and unplug vacuum, disconnect the nozzle and remove
blockage before reconnecting and turning vacuum back on.
Pull the handle toward you and release the floor nozzle to disengage the
auto-off feature.
Move the On/Off switch to the “II - Brush Roll On” position.
Vacuum turns off on its
own.
This vacuum cleaner is equipped with a motor protective thermostat. If for
some reason your vacuum overheats, the thermostat will automatically turn
the unit off. Should this occur, perform the following steps to restart the
motor thermostat:
1. Move the On/Off switch to the “O” (Off) position.
2. Unplug the vacuum.
3. Empty the dust cup and clean filters.
4. Check for blockages in hose, accessories and inlet openings.
5. Allow the unit to cool for a minimum of 45 minutes.
6. Plug in the vacuum.
7. Turn the On/Off switch to the “I” (On) position to restart the vacuum.
Note: If vacuum still does not start, contact Customer Service at:
1-800-798-7398.
Troubleshooting Guide
17www.sharkclean.com
English
English
PART PART NO.
1 Pre-Motor Filter Set XFF350
2 HEPA Filter XHF350
3 Dusting Brush and Crevice Tool 112FFJ
4 Power Brush 137FFJ
5 Ex tension Wand 1116FC
6 Appliance Wand 120FLI360
Ordering Parts
To purchase replacement parts, please visit our website: www.sharkclean.com
or contact customer service: 1-800-798-7398.
4
3
1
2
5
6
18 SANS FRAIS: 1-800-798-7398
AVERTISSEMENT : Pour
réduire le risque d’électrocution,
n’utilisez pas l’appareil à l’extérieur
ou sur des surfaces mouillées.
AVERTISSEMENT :
POUR RÉDUIRE LE RISQUE D’INCENDIE,
D’ÉLECTROCUTION ET DE BLESSURES :
INSTRUCTIONS DE SÉCURITÉ ÉLECTRIQUE
GÉNÉRALES :
1. Débranchez l’aspirateur de la prise de courant
lorsqu’il n’est pas utilisé et avant tout entretien.
2. N’UTILISEZ PAS l’aspirateur si sa fiche ou
son cordon sont endommagés. Si l’appareil ne
fonctionne pas comme il se doit, a été échappé,
endommagé, laissé à l’extérieur ou échappé dans
l’eau, veuillez le retourner à SharkNinja Operating
LLC pour une vérification, pour un réglage ou pour
une réparation.
3. NE DÉPLACEZ PAS l’appareil en tirant sur son
cordon d’alimentation.
4. NE DÉBRANCHEZ PAS l’appareil en tirant sur le
cordon d’alimentation; pour le débrancher, agrippez
la fiche et non le cordon.
5. NE MANIPULEZ PAS la fiche ou l’appareil avec
des mains humides.
6. NE PASSEZ PAS l’aspirateur sur le cordon
d’alimentation.
7. N’UTILISEZ PAS le cordon comme une poignée.
8. NE FERMEZ PAS une porte sur le cordon.
9. NE TIREZ PAS le cordon en le faisant passer
sur des rebords coupants. Nous déconseillons
l’utilisation d’une rallonge électrique.
10. NE LAISSEZ PAS l’appareil branché sans
surveillance.
11. Tenez le cordon loin des surfaces chaudes.
12. Éteignez toutes les commandes avant de brancher
ou de débrancher l’aspirateur.
13. Veuillez toujours mettre cet appareil hors tension
avant de brancher ou de débrancher l’accessoire
motorisé.
14. Lors du rangement de l’appareil, enroulez
fermement le cordon d’alimentation autour des
deux crochets à cordon – comme illustré dans les
instructions de rangement.
MESURES DE SÉCURITÉ IMPORTANTES
Pour usage domestique seulement
LORSQUE VOUS UTILISEZ UN APPAREIL
ÉLECTRIQUE, DES MESURES DE SÉCURITÉ
ÉLÉMENTAIRES DEVRAIENT TOUJOURS
ÊTRE RESPECTÉES, Y COMPRIS LES
MESURES SUIVANTES : LISEZ TOUTES LES
INSTRUCTIONS AVANT D’UTILISER VOTRE
ASPIRATEUR NAVIGATOR
MD
LIFT-AWAY
MC
DE LUXE DE SHARK
MD
.
FICHE POLARISÉE :
Afin de réduire les risques d’électrocution, cet
appareil a été muni d’une fiche polarisée (une
broche est plus large que l’autre). Par mesure
de sécurité, cette fiche ne peut être insérée que
d’un seul côté dans une prise polarisée. Si la
fiche ne s’insère pas complètement dans la prise
de courant, inversez-la. Si cela ne fonctionne
toujours pas, contactez un électricien compétent.
NE forcez PAS et ne modifiez pas la
fiche pour la brancher dans une prise
murale.
19www.sharkclean.com
Français
ACCESSOIRES POUR TUYAU SOUPLE :
1. N’UTILISEZ PAS l’appareil si le débit d’air est
restreint; si les conduits d’air, le tuyau souple ou
les accessoires sont obstrués, éteignez l’aspirateur.
Retirez toutes les obstructions avant de remettre
l’appareil en marche.
2. Gardez l’extrémité du tuyau souple et les orifices
d’aspiration des accessoires éloignés de votre
visage et de votre corps.
3. Gardez les accessoires de nettoyage et les orifices
d’aspiration éloignés de vos cheveux, de votre
visage, de vos doigts, de vos pieds nus et de
vêtements amples.
4. N’utilisez que les accessoires recommandés par le
fabricant.
UTILISATION GÉNÉRALE :
1. Utiliser l’appareil seulement de la façon décrite
dans ce guide.
2. N’INSÉREZ PAS d’objets dans les ouvertures.
N’utilisez PAS l’appareil si des ouvertures sont
obstruées; assurez-vous que les ouvertures sont
libres de poussière, peluches, cheveux et d’objets
pouvant réduire le débit d’air.
3. Assurez-vous que votre espace de travail est bien
éclairé.
4. L’aspirateur doit toujours être en mouvement sur le
tapis afin d’éviter d’endommager les fibres.
5. NE PLACEZ PAS l’aspirateur sur des surfaces
instables telles que des chaises et des tables.
6. NE PERMETTEZ PAS aux jeunes enfants
d’utiliser l’appareil ou de s’en servir comme jouet.
Une surveillance étroite est nécessaire lorsque
l’appareil est utilisé par un enfant ou à proximité
d’un enfant.
7. N’UTILISEZ PAS l’aspirateur s’il a été échappé,
endommagé, utilisé à l’extérieur ou immergé dans
l’eau. Retournez l’appareil à SharkNinja Operating
LLC pour vérification, réparation ou réglage.
8. N’utilisez PAS l’appareil si le récipient à
poussière et (ou) les filtres ne sont pas en place.
RÉCIPIENT À POUSSIÈRE / FILTRES /
ACCESSOIRES :
Avant de mettre l’aspirateur en marche :
1. Assurez-vous que les filtres sont complètement secs
après le nettoyage de routine.
2. Après avoir effectué l’entretien de routine, assurez-
vous que le récipient à poussière et tous les filtres
sont bien en place.
3. Assurez-vous que les accessoires sont libres de
toute obstruction.
4. Utilisez seulement les filtres et accessoires fournis
par SharkNinja Operating LLC. [À défaut de quoi, la
garantie sera annulée.]
NETTOYAGE GÉNÉRAL :
1. NE RAMASSEZ PAS de gros objets.
2. N’ASPIREZ PAS des objets durs ou pointus
comme du verre, des clous, des vis ou de la
monnaie, lesquels pourraient endommager
l’aspirateur.
3.
N’ASPIREZ PAS d’objets fumants ou brûlants
comme des charbons chauds, des cendres chaudes,
des bouts de cigarettes ou des allumettes.
4. N’UTILISEZ PAS l’aspirateur pour ramasser de la
poussière de cloison sèche.
5. N’ASPIREZ PAS de liquides inflammables ou
combustibles tels que de l’essence à briquets, du
carburant, du kérosène; n’utilisez pas l’aspirateur
dans des endroits où ces produits peuvent être
présents.
6. N’UTILISEZ PAS l’aspirateur pour aspirer des
solutions toxiques telles que de l’eau de javel, de
l’ammoniac ou du nettoyeur à drains.
7. N’UTILISEZ PAS l’appareil dans des endroits clos
où il y a des vapeurs provenant de la peinture, des
diluants à peinture, des substances antimites, de
la poussière inflammable ou tout autre matériau
explosif ou toxique.
8. N’ASPIREZ aucun liquide.
9. N’IMMERGEZ PAS l’appareil dans l’eau ou dans
un autre liquide.
10. N’UTILISEZ PAS l’appareil à l’extérieur ou sur des
surfaces mouillées; utilisez l’appareil uniquement
sur des surfaces sèches.
11. Soyez particulièrement prudent en nettoyant les
escaliers.
VEUILLEZ CONSERVER
CES INSTRUCTIONS
20 SANS FRAIS: 1-800-798-7398
Ce manuel concerne le modèle :
UV490CCO 26
SPÉCIFICATIONS TECHNIQUES
Tension : 120 V., 60 Hz
Puissance nominale : 1200 W
Ampères : 10 A
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
Shark UV490CCO Manuel utilisateur
- Catégorie
- Aspirateurs
- Taper
- Manuel utilisateur
dans d''autres langues
- English: Shark UV490CCO User manual
Documents connexes
-
Shark UV541CCO Manuel utilisateur
-
-
Shark NV370 Manuel utilisateur
-
-
-
-
-
-
-
