Topcon SL-100 Installation And Setup Gude

3,

)NSTALLATIONAND3ETUP'UIDE

POSITIONING SYSTEMS

SL-100

Upgrade Kit

Installation and Setup Guide

Part Number 1000226-01

Rev. A

ECO XXXXXX

©Copyright Topcon Positioning Systems, Inc.

August 2012

used, accessed, copied, stored, displayed, sold, modified, published, distributed, or otherwise reproduced without express

written consent from Topcon.

Terms and Conditions

Thank you for buying this Topcon product. This manual has been prepared to assist you with the installation of the product and its use

is subject to these Terms and Conditions.

Usage and Safety

This product is designed for use by professionals. Always use safety precautions when operating this or any Topcon product.

Copyrights

All information contained in this Manual is the intellectual property of, and copyrighted material of TPS. All rights are reserved. You

may not use, access, copy, store, display, create derivative works of, sell, modify, publish, distribute, or allow any third party access to,

any graphics, content, information or data in this Manual without TPS’ express written consent and may only use such information for

the care and operation of your Product. The information and data in this Manual are a valuable asset of TPS and are developed by the

expenditure of considerable work, time and money, and are the result of original selection, coordination and arrangement by TPS.

Trademarks

3DMC, SL-100, MC-R3, GX-60, Topcon, and Topcon Positioning Systems are trademarks or registered trademarks of TPS.

Other product and company names mentioned herein may be trademarks of their respective owners.

Disclaimer of Warranty

EXCEPT FOR SUCH WARRANTIES AND LICENSES PROVIDED WITH THE PRODUCT, THIS MANUAL AND THE PRODUCT ARE PROVIDED

“AS-IS”. T

OPCON AND ITS DISTRIBUTORS SHALL NOT BE LIABLE FOR TECHNICAL OR EDITORIAL ERRORS OR OMISSIONS

CONTAINED HEREIN; NOR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE FURNISHING, PERFORMANCE OR

USE OF THIS MATERIAL OR THE PRODUCT.

Please see the Operator’s/User’s Manual for detailed information on warranties and the license agreement which may apply to the

Product.

License Agreement

Use of any computer programs or software supplied by Topcon or downloaded from the Topcon website in connection with the Product

implies acceptance of the Terms and Conditions here and in the Operator’s/User’s Manual.

Please see the Operator’s/User’s Manual for detailed information on warranties and the license agreement which may apply to the

Product.

P/N 1000226-01

i

TOC

Table of Contents

Introduction .................................................................... 1

Installation ...................................................................... 2

SL-100 SIM Card .................................................................................... 2

Mag Mount Kit (Optional) ..................................................................... 3

9911-1014 Ethernet Cable to

MC-R3 Breakout B Cable Connection ................................................ 4

9911-1015 Power and Serial Cable to

MC-R3 Breakout A Cable Connection ................................................ 6

SL-100 and SL-R3 Antenna Installation ................................................ 9

SL-100 Cable Connection ....................................................................... 9

SL-100 Configuration ..................................................... 11

Enter SiteLINK Configuration Tool Web Interface ......................... 11

Check SL-R3 Firmware .................................................................... 12

Configure SL-100 for Cellular .......................................................... 13

Configure SIM Card (GPRS) ............................................................ 15

Configure VPN (If Running VPN on the SiteLINK Server) ............ 16

Configure SiteLINK Server .............................................................. 18

Check OpenVPN Status (If Running VPN) ...................................... 20

3DMC Configuration ...................................................... 21

Install 3DMC SiteLINK Authorization Codes ................................. 21

Connecting to the SiteLINK Server .................................................. 22

SiteLINK Direct ................................................................................ 24

Direct Network Connection .............................................................. 25

SL-100 LED Status ......................................................... 26

Table of Contents

SL-100 Upgrade Kit Installation and Setup Guide

ii

Safety Warnings ............................................................ 27

RF Radiation Hazard Warning ............................................................... 27

Regulatory Information ................................................. 27

IC Statements .......................................................................................... 27

Déclaration de conformité IC: ................................................................ 28

P/N 1000226-01

1

Introduction

Developed as an add-on component to a standard Topcon 3D system, the SL-100 is a rugged

housing for the SL-R3 SiteLINK radio modem, providing a SiteLINK-ready solution on the job

site for a variety of construction machines.

This manual describes how to install the SL-100, radio antenna, and cables, and how to configure

your unit.

Figure 1. SL-100

1000221-01 KIT, SL-100 Upgrade

• 1 ea. ASSY, SL-100 W/ SL-R3

• 1 ea. Power Cable - SL-100 to MC-R3, 9 ft. 11 in. (3000mm)

• 1 ea. Ethernet Cable - SL-100 TO MC-R3, 9 ft. 11 in. (3000mm)

• 1 ea. Kit, Antenna Config SL-R3

• 1 ea. SL-100 Upgrade Kit Installation and Setup Guide

• 1 ea. #20 Deutsch Removal Tool

1000222-01 KIT, SL-100 - MC-R3 Breakout B Connector (Optional)

• 1 ea. SL-100 – MC-R3 Breakout B Connector

• 1 ea. DRC26-40 MC-R3 Breakout B Connector Dust Boot

1000220-01 SL-100 Mag Mount Kit (Optional)

Installation

SL-100 Upgrade Kit Installation and Setup Guide

2

Additional Parts Required

• 3DMC upgrade to:

– 7050-1106 Password, 3DMC Standard + SiteLINK

– 7050-1106 Password, 3DMC Standard + SiteLINK Advanced

• SIM Card (SIM APN, Username, Password)

Installation

SL-100 SIM Card

1. Remove the eight (8) retaining screws from the base of the SL-100.

Figure 2. Remove Screws

2. Remove the base.

Figure 3. Remove Base

Remove Screw

8 Plcs.

Mag Mount Kit (Optional)

P/N 1000226-01

3

3. Insert the SIM card into the SIM card slot.

Figure 4. Insert SIM Card

4. Reinstall the eight (8) retaining screws onto the SL-100 base using Blue Loctite (not

included), and torque to 12 in-lbs

.

Mag Mount Kit (Optional)

If you are installing the optional Mag Mount Kit (P/N: 1000220-01), refer to the Mag Mount

Installation Instructions (P/N: 7010-1026).

SIM Card Slot

Installation

SL-100 Upgrade Kit Installation and Setup Guide

4

9911-1014 Ethernet Cable to

MC-R3 Breakout B Cable Connection

1. Locate the existing installed MC-R3 Breakout B cable attached to Conn B of the MC-R3.

Figure 5. Breakout B Cable

2. Disconnect the Breakout B cable from the MC-R3.

3. Pull back the rubber boot on the Breakout B cable to expose the wire comb.

Figure 6. Expose Wire Comb

NOTICE

If the existing system does not have a Breakout B cable attached to Conn B, you

must have the SL-100 MC-R3 B Connector Kit (P/N: 1000222-01) to complete

the install.

Breakout B Connector

Rubber Boot

Wire Comb

9911-1014 Ethernet Cable to MC-R3 Breakout B Cable Connection

P/N 1000226-01

5

4. To remove the sealing plugs from pins 6, 16, 26, and 36 from the wire comb 

(see Figure 7), insert a large paper clip, or something similar into the mating end of the

connector, and push out the sealing plug.

Figure 7. Remove 4 Sealing Plugs

5. Route the new Ethernet cable through the rubber boot.

Figure 8. Route Ethernet Cable through Boot

Wire Comb

Remove 4

Sealing Plugs

Ethernet Cable Routed through

Rubber Boot

Wire Comb

Installation

SL-100 Upgrade Kit Installation and Setup Guide

6

6. Install the wires according to the colors noted in the wiring diagram (Figure 9). Slide the

wires/contacts into the connector until they lock in place.

Figure 9. Ethernet to MC-R3 Breakout B Cable Wiring Diagram

7. Connect the MC-R3 Breakout B cable to the MC-R3 Controller, slide the rubber boot back

into place, and tighten the Breakout B Connector screw.

9911-1015 Power and Serial Cable to

MC-R3 Breakout A Cable Connection

1. Locate the existing installed MC-R3 Breakout A cable attached to Conn A of the MC-R3.

Figure 10. Breakout A Cable

2. Disconnect the cable from the MC-R3.

BLUE

YELLOW

WHITE

Ethernet Cable

(9911-1014)

ORANGE

MC-R3

Breakout B

Eth RX+

Eth RX-

Eth TX+

Eth TX-

26

16

6

36

Breakout A Connector

9911-1015 Power and Serial Cable to MC-R3 Breakout A Cable Connection

P/N 1000226-01

7

3. Pull back the rubber boot on the Breakout A cable to expose the wire comb.

Figure 11. Expose Wire Comb

4. To remove the sealing plugs from pins 5, 17, 27, 34, 37 & 39 from the wire comb, insert a

large paper clip, or something similar, into the mating end of the connector, and push out

each sealing plug.

Figure 12. Remove 6 Sealing Plugs

Rubber Boot

Wire Comb

Remove 6

Sealing Plugs

Installation

SL-100 Upgrade Kit Installation and Setup Guide

8

5. Route the new Power/Serial cable (9911-1015) through the rubber boot.

Figure 13. Route Power/Serial Cable through Boot

6. Install the wires according to the colors noted in the wiring diagram (Figure 14). Slide the

wires/contacts into the connector until they lock in place.

Figure 14. Power/Serial to MC-R3 Breakout A Cable Wiring Diagram

7. Connect the MC-R3 Breakout A cable to the MC-R3 Controller, slide the rubber boot

back into place, and tighten the Breakout B Connector screw.

Power/Serial Cable Routed through

Rubber Boot

Wire Comb

ORANGE

BROWN

YELLOW

Power/Serial Cable

(9911-1015)

BLUE

MC-R3

Breakout A

MAIN A TX

MAIN A RX

AUX A TX

AUX A RX

RED

V SUPPLY

BLACK

GROUND

27

5

34

17

37*

39**

* If in use, use pin 38 as an alternative to pin 37

** If in use, use pin 19 or 29 as an alternative to pin 39

SL-100 and SL-R3 Antenna Installation

P/N 1000226-01

9

SL-100 and SL-R3 Antenna Installation

Install the SL-100 and the SL-R3 antenna on your machine where appropriate.

SL-100 Cable Connection

Connect the following cables to the SL-100

From the MC-R3 Controller Cable

• 9911-1014 - Ethernet Cable (Black Connector)

• 9911-1015 - Power Cable (Grey Connector)

From the SL-R3 Antenna

• 9050-18 - SL-R3 Antenna

Installation

SL-100 Upgrade Kit Installation and Setup Guide

10

Notes:

P/N 1000226-01

11

SL-100 Configuration

To use the GX-60 Display to configure the SL-100:

Enter SiteLINK Configuration Tool Web Interface

1. Power up your 3DMC SiteLINK system by turing on the GX-60 display. The SL-100 and

MC-R3 controller powers up with the GX-60.

2. Start Windows® Internet Explorer on the GX-60 Display.

3. Using the on-screen keyboard, type 192.168.0.1 into Internet Explorer’s address bar to

connect to the SiteLINK Configuration Tool web interface.

Figure 1. Access SiteLINK Configuration Tool Web Interface

4. When prompted for the user name and password, enter ”admin” for both.

Figure 2. Enter SiteLINK Username and Password

SL-100 Configuration

SL-100 Upgrade Kit Installation and Setup Guide

12

Check SL-R3 Firmware

The firmware version is listed at the top of every page (Figure 3).

Figure 3. Firmware Version

If the firmware needs upgrading, click Admin --> Firmware on the left side of the page and load

the new firmware (Figure 4).

Figure 4. Load New Firmware

P/N 1000226-01

13

Configure SL-100 for Cellular

1. Click Device --> General on the left side of the page to enter the General Device

Configuration page (Figure 5).

Figure 5. Configure Device Mode to Cellular

2. Check that the Device Mode is set to Cellular (factory default). See Figure 6.

• If the Device Mode is set to Cellular, skip step 3 and go to “Configure SIM Card

(GPRS)” on page 1-15.

• If the Device Mode is not set to Cellular, select Cellular from the Device Mode

drop-down menu, and press Save.

NOTICE

Do not choose any option other than cellular.

SL-100 Configuration

SL-100 Upgrade Kit Installation and Setup Guide

14

Figure 6. Device Mode - Cellular

3. Click Admin --> Reboot on the left side of the page to enter the Reboot page, and press

Reboot.

Figure 7. Reboot

La page charge ...

Topcon SL-100 Installation And Setup Gude

Topcon SL-100 Installation And Setup Gude

dans d''autres langues

Documents connexes

Autres documents