ResMed S8 Manuel utilisateur

S8 Series II

S8 AutoSet™ II

S8

Elite™ II

POSITIVE AIRWAY PRESSURE DEVICES

User Guide

English • Français • Español • Português

Rx Only

ResMed Ltd (Manufacturer) 1 Elizabeth Macarthur Drive Bella Vista NSW 2153 Australia

ResMed Corp (US Designated Agent) 14040 Danielson Street Poway CA 92064-6857 USA

ResMed (UK) Ltd (EU Authorized Representative) 96 Milton Park Abingdon Oxfordshire OX14 4RY UK

ResMed Offices Australia, Austria, Brazil, China, Finland, France, Germany, Hong Kong, India, Japan, Malaysia, Netherlands, Norway, New Zealand,

Singapore, Spain, Sweden, Switzerland, UK, USA (see www.resmed.com for contact details).

Protected by patents: AU 691200, AU 697652, AU 709279, AU 724589, AU 730844, AU 736723, AU 750095, AU 750761, AU 764761, AU 779327, AU

2002231456, CN 02804930.6, EP 0651971, EP 0661071, EP 0920845, EP 0934723, EP 1028769, EP 1126893, EP 1502618, EP 1144036, JP 3580776, JP

3778797, NZ 504595, US 5199424, US 5245995, US 5522382, US 5704345, US 6029665, US 6138675, US 6240921, US 6363933, US 6367474, US 6398739,

US 6425395, US 6502572, US 6591834, US 6635021, US 6705315, US 6745768, US 6817361, US 6988498, US 7004908, US 7040317, US 7100608, US

7141021. Other patents pending.

Protected by design registrations: AU 302180, AU 302181, AU 302182, AU 302183, AU 302184, AU 302185, AU 302186, CN 200430121212.2, CN

200430121213.7, CN 200430121211.8, CN 200430121214.1, CN 200430121215.6, CN 200430121216.0, CN 200430121217.5, EP 269436, HK 0412901.9, JP

1257662, JP 1257663, JP 1266956, JP 1266957, JP 1267270, JP 1267271, NZ 405614, NZ 406923, NZ 406924, NZ 406925, NZ 406926, NZ 406927, NZ

406928, US D544598, US D553228. Others pending.

S8, S8 AutoSet, S8 Elite and SmartStart are trademarks of ResMed Ltd and AutoSet and HumidAire are registered in U.S. Patent and Trademark Office.

English

S8 Series II

S8 AutoSet™ II

S8

Elite™ II

POSITIVE AIRWAY PRESSURE DEVICES

User Guide

English

Rx Only

i

Contents

Indications for Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

S8 AutoSet II 1

S8 Elite II 1

Contraindications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Adverse Effects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Parts of the S8 Series II system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Masks 2

Humidifiers 2

Setting up the S8 Series II . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Connecting the Device 3

Selecting the Mask Type 3

Using the Mask-fitting Feature 3

Starting Treatment 4

Stopping Treatment 5

Changing the Settings on your S8 II Device . . . . . . . . . . . . . . . . . 5

The Standard Menu 5

The Detailed Menu 7

Messages on the S8 Series II LCD . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Using the Data Card to Collect Data . . . . . . . . . . . . . . . . . . . . . . . . 9

Copy Data onto the Data Card 9

Cleaning and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Daily 10

Weekly 10

Monthly 11

Replacing the Air Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Technical Specifications 15

Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

1Indications for Use

English

Indications for Use

S8 AutoSet II

The S8 AutoSet II self-adjusting sleep apnea system is indicated for the treatment of

obstructive sleep apnea (OSA) in adult patients. The S8 AutoSet II self-adjusting sleep

apnea system has two treatment modes: AutoSet and fixed-pressure CPAP.

The S8 AutoSet II

system is intended for home and hospital use.

S8 Elite II

The S8 Elite II continuous positive airway pressure (CPAP) system is indicated for the

treatment of obstructive sleep apnea (OSA) in adult patients.

The S8 Elite II

CPAP system is intended for home and hospital use.

Contraindications

Your S8 Series II is not a life-support device and may stop operating during power

failure or certain fault conditions. It should not be used by patients who are dependent

on continuous therapy.

Positive airway pressure therapy may be contraindicated in some patients with the

following pre-existing conditions:

• severe bullous lung disease

• pneumothorax

• pathologically low blood pressure

• dehydration

• cerebrospinal fluid leak, recent cranial surgery, or trauma.

Adverse Effects

Patients should report unusual chest pain, severe headache, or increased

breathlessness to their prescribing physician. An acute upper respiratory tract infection

may require temporary discontinuation of treatment.

The following side effects may arise during the course of therapy with the CPAP device:

• drying of the nose, mouth, or throat

• nosebleed

• bloating

• ear or sinus discomfort

• eye irritation

• skin rashes.

Parts of the S8 Series II system

Your S8 Series II device comprises:

• S8 Series II device

• Power cord

• Carry bag

• 2 m air tubing.

2

Accessories available:

• Integrated humidifier

• Front cap

• 3 m air tubing

• DC-12 converter

• ResMed Tubing Wrap.

Masks

A list of masks (and their settings) compatible with these devices can be found on

www.resmed.com, on the Products page under Service and Support.

Humidifiers

A list of humidifiers compatible with ResMed devices can be found on

www.resmed.com, on the Products page under Service and Support.

Setting up the S8 Series II

!

WARNING

• Make sure the power cord and plug are in good condition and the

equipment is not damaged.

• Only ResMed air tubing should be used with the device. A different type of

air tubing may alter the pressure you actually receive and reduce the

effectiveness of your treatment.

• Blocking the hose and/or air inlet of the device while in operation could lead

to overheating of the device.

!

CAUTION

• Be careful to place the device where it cannot be bumped, and where no one

will trip over the power cord.

• If you put the device on the floor, make sure the area is free from dust and

clear of bedding, clothes or other objects that could block the air inlet.

• Make sure the area around the device is dry and clean.

Carry handle

Screen

Keypad

Air outlet

DC

AC

Data Card

slot

3Setting up the S8 Series II

English

Connecting the Device

Selecting the Mask Type

To ensure your device functions as intended with your selected mask, you need to

select the mask type that you are using.

1 With the RAMP or SETTLING screen displayed, press . (In CPAP mode, the

standby screen displays RAMP. In AutoSet mode (S8 AutoSet II only) the

standby screen displays SETTLING.)

2 Press until MASK is displayed.

3 Press to change the setting.

4 Press or until you see the setting that you require.

5 Press to apply.

Using the Mask-fitting Feature

You can use the S8 Series II mask-fitting feature to help you fit your mask properly. This

feature delivers air pressure for a three-minute period, prior to starting treatment,

during which you can check and adjust your mask fit to minimize leaks.

Note: Make sure that the mask setting on the MASK screen is the same as the mask you

are using.

1 Fit your mask as described in the mask user instructions.

2 With the RAMP or SETTLING screens displayed, hold down for at least

three seconds until air pressure delivery starts.

1

2

3

4

LCD and Keypad

4

Your device will ramp to the mask-fit pressure and will remain at this pressure

for three minutes.

The following displays on the LCD screen indicating that the mask-fitting feature

is operating, where: ***** is an excellent fit;****- is a very good fit; ***-- is a

good fit; while **---, *---- and ----- each require you to adjust your mask.

3 Adjust your mask, mask cushion and headgear until you have a secure and

comfortable fit.

After three minutes, the pressure reverts to the set pressure and treatment will

begin. If you do not wish to wait three minutes, hold down for at least

three seconds to start treatment immediately.

If you press for less than three seconds, the unit will return to standby

mode (the RAMP or SETTLING screen).

Starting Treatment

1 Make sure the power is on. The product name is displayed briefly on the screen,

then the standby screen displays RAMP (or SETTLING). Press or to

increase or decrease the ramping (or settling) period.

2 Fit mask, lie down and arrange the air tubing so that it is free to move if you turn

in your sleep.

!

CAUTION

Do not leave long lengths of air tubing around the top of your bed. They could

twist around your head or neck while you are sleeping.

3 To start treatment, press .

If your clinician has set up the device to start delivering therapy automatically

using SmartStart™, your device will start when you breathe into your mask.

4 Fit your mask as described in the mask user instructions.

!

WARNING

A mask should not be used unless the S8 Series II device is powered and

operating properly.

When treatment begins, if ramp is set, the pressure increases from a low

pressure to the prescribed treatment pressure over the set period. Ramping is

designed to help you adjust to an increase in pressure gradually, and enhance

your comfort.

MASK FIT:

*****

excelnt

5Changing the Settings on your S8 II Device

English

Stopping Treatment

To stop treatment at any time, remove your mask and press .

If your clinician has enabled SmartStart, simply remove your mask and treatment will

end.

Changing the Settings on your S8 II Device

You can change settings (such as Ramp Time, EPR Level) on the S8 II by using the

keypad and LCD. When the device is in standby mode you can display a series of

screens (a menu) on the LCD screen in order to view and change the settings for a

particular function.

The Standard Menu

Your clinician will have enabled the menu on your S8 Series II device. The picture

shows the standard menu in each mode.

Note: The AutoSet menu is available on the S8 AutoSet II only.

To enter the standard menu from the standby (RAMP or SETTLING) screen, press

.

S8 CLASSICRAMP: 10min

menu

S8 CLASSIC

WELCOME

>>>>>>

S8 CLASSICSETTLING: 10min

menu

S8 CLASSIC

WELCOME

>>>>>>

EPR LEVEL: 1

change exit

CPAP

AUTOSET

MASK: ULTRA

change exit

exit

SW: SX4800100

USED HRS: 08000

exit

USAGE: 1000/1068

exit

MASK: ULTRA

change exit

exit

SW: SX4800100

USED HRS: 08000

exit

USAGE: 1000/1068

exit

EPR LEVEL: 1

change exit

* Only displayed if access set by clinician.

*

6

You can use this menu to change the:

• Expiratory Pressure Relief (EPR) settings

Your clinician may have set up your device to deliver EPR. This can be used to help

ease any discomfort you may experience when breathing out during treatment.

There are four settings: OFF (no EPR); 1 (lowest EPR); 2; and 3 (highest EPR).

The EPR LEVEL screen only appears if your clinician has enabled access to the EPR

settings.

To change the EPR level, select . Press or until you see the

setting that you require.

• Mask type – see page 3.

You can also view the total number of hours of treatment (USED HRS); the number of

sessions that the S8 Series II device was used in a usage period (USAGE); and the

current software version (SW).

7Changing the Settings on your S8 II Device

English

The Detailed Menu

Your clinician may have enabled a detailed menu on your S8 Series II device. The

picture shows the detailed menu in each mode.

Note: The AutoSet menu is available on the S8 AutoSet II only.

To enter the detailed menu from the standby (RAMP or SETTLING) screen, press .

The SETTINGS menu screen is displayed.

RAMP: 10min

menu

WELCOME

>>>>>>

SETTINGS

enter exit

SETTLING: 10min

menu

WELCOME

>>>>>>

EPR LEVEL: 1

change exit

MASK: ULTRA

change exit

TUBE LENGTH: 2m

change exit

HUM

ID: NONE

change exit

SMARTSTART: ON

change exit

LEAK ALERT: OFF

change exit

CPAP

AUTOSET

MASK: ULTRA

change exit

TUBE LENGTH: 2m

change exit

HUM

ID: NONE

change exit

SMARTSTART: ON

change exit

LEAK ALERT: OFF

change exit

AUTOSETCPAP

USED HRS: 08000

exit

USAGE: 1000/1068

exit

RESULTS

enter exit

SERVICING

enter exit

OPTIO

NS

enter exit

LANG: ENGLIS

H

change exit

SN: 12345678912

exit

PCB: 123456789123

4567 exit

SW: SX4800100

exit

SM

AR

T

DATA

enter exit

SM

AR

T

DATA

enter exit

AUTO

APPEAR: OFF

change cancel

EPR LEVEL: 1

change exit

**

* Only displayed if access set by clinician.

**

*

8

Settings Menu

Select on the Settings menu to access the options in this menu.

You can use the Settings menu to change the:

• Expiratory Pressure Relief (EPR) settings – see page 6.

• Mask type – see page 3.

• Tube length

Scroll to TUBE LENGTH and select .

Press or until you see the setting that you require.

• Front cap

You can set up your device to use the front cap accessory.

Scroll to HUMID and select .

Press or until you see the setting that you require.

• SmartStart settings

SmartStart enables your device to start automatically when you breathe into the

mask.

Scroll to SMARTSTART and select .

Press or to change the option to ON or OFF.

• Leak alert settings

Leak alert indicates when a high mask leak is present.

Scroll to LEAK ALERT and select .

Press or to change the option to ON or OFF.

Results Menu

Select on the Results menu to access the options in this menu.

You can use the Results menu to view the total number of hours of treatment (USED

HRS) and the number of sessions that the S8 AutoSet II was used in a usage period

(USAGE).

Note: Your clinician may have customized your device to display Smart Data. Contact

your clinician for further details about Smart Data.

Options Menu

Select on the Options menu to access the options in this menu.

You can use the Options menu to change the language setting. Scroll to LANG and

select . Press or until you see the setting that you require.

Servicing Menu

Select on the Servicing menu to access the options in this menu.

You can use the Servicing menu to view the device system information.

9Messages on the S8 Series II LCD

English

Messages on the S8 Series II LCD

Your clinician may have set your S8 Series II device to remind you about important

events, such as when to replace your mask, when to insert your Data Card (if your

device is Data Card enabled) and so on.

The reminder message is displayed on the LCD and is visible if the device is not

delivering therapy. The backlight on the LCD flashes when a message is displayed.

Your clinician can set any of the following reminders on your LCD:

Using the Data Card to Collect Data

If your clinician needs to review your treatment, they will ask you to use the Data Card

to copy data from your S8 Series II, and to return the card to them. The Data Card will

be provided in a protective folder.

Data that is copied to a Data Card is still stored and available on the S8 Series II device.

Copy Data onto the Data Card

1 Switch on the S8 Series II and wait until you see the standby (Ramp) screen.

2 Hold the Data Card with the arrow facing up and insert it into the Data Card slot

until it stops. Data copying starts automatically.

The “Card Inserted Please Wait” message is displayed on the S8 Series II LCD

while data is being copied. Copying takes approximately five seconds.

The “Copy Complete Remove Card” message is displayed on the LCD when

copying has finished.

Message Description Action

INSERT

CARD

May appear if your device is

Data Card enabled.

Insert your Data Card and follow any

instructions that your clinician has given you.

When you have done this, the message will

disappear from the LCD. Pressing (Ok)

will also remove the message.

REPLACE

MASK

May appear when your mask

is due for replacement.

Press (Ok) to remove the message

from your LCD, and replace your mask with a

new one.

CALL

PROVIDER

May appear as a reminder to

contact your clinician, eg, to

discuss how your therapy is

going.

Press (Ok) to remove the message

from your LCD, and contact your clinician.

REPLACE

FILTER

May appear as a reminder to

replace the air filter on your

device.

Press (Ok) to remove the message

from your LCD, and replace the air filter.

SERVICE

DUE

May appear as a reminder to

return your device for service.

Press (Ok) to remove the message

from your LCD, and contact your clinician.

10

3 Remove the Data Card by gripping the end of the Data Card and pulling it out.

4 Store the Data Card in its protective folder when not in use.

5 Return the card in its protective folder to your clinician using a postal envelope.

Using the Data Card to Update Settings

If your clinician has provided a Data Card with new device settings:

1 With the device in standby (Ramp) mode, insert the Data Card into the Data Card

slot. Updating will start automatically.

The “Card Inserted Please Wait” message is displayed on the LCD while

updating is in progress. Updating takes approximately five seconds.

The “Settings Success Remove Card” message is displayed on the LCD if the

settings were updated successfully.

Note: This message only appears once. If you re-insert the Data Card after you

have updated your settings, this message is not displayed.

2 Remove the Data Card from the S8 Series II.

3 Store the Data Card in its protective folder when not in use.

!

WARNING

If your clinician has told you to use this Data Card to update the settings on your

device and the “Settings Success” message does not appear, contact your

clinician immediately.

Cleaning and Maintenance

!

WARNING

Beware of electric shock. Do not immerse the device or power cord in water.

Always unplug the device before cleaning and make sure it is dry before

reconnecting.

!

CAUTION

• Do not hang the air tubing in direct sunlight as it may harden over time

and eventually crack.

• Do not use bleach, chlorine, alcohol, or aromatic-based solutions,

moisturizing or antibacterial soaps or scented oils to clean the air tubing or

the device. These solutions may cause hardening and reduce the life of the

product.

Daily

Disconnect the air tubing and hang it in a clean, dry place until next use.

Weekly

1 Remove the air tubing and wash it in warm water using mild detergent.

11Replacing the Air Filter

English

2 Rinse thoroughly, hang, and allow to dry.

3 Before next use, reassemble the mask and headgear.

4 Reconnect the air tubing.

Monthly

• Clean the exterior of the S8 Series II with a damp cloth and mild liquid soap.

• Check the air filter for holes and blockage by dirt. Replace it every six months, or

more often in a dusty environment.

Replacing the Air Filter

!

CAUTION

• Do not wash the air filter. The air filter is not washable or reusable.

• The air filter cover protects the device in the event of accidental liquid

spillage onto the device. Ensure the air filter and air filter cover are fitted at

all times.

1 Remove the air filter cover at the back of the device.

2 Remove and discard the old air filter.

3 Insert a new filter with the blue tinted side facing out from the device.

4 Replace the air filter cover.

Servicing

This product (S8 AutoSet II; S8 Elite II) should be inspected by an authorized ResMed

service centre five years from the date of manufacture. Prior to this, the device is

intended to provide safe and reliable operation provided that it is operated and

maintained in accordance with the instructions provided by ResMed. Applicable

ResMed warranty details are provided with the device at the time of original supply. Of

course, as with all electrical devices, if any irregularity becomes apparent, you should

exercise caution and have the device inspected by an authorized ResMed service

centre.

If you feel that your device is not performing properly, see “Troubleshooting” on

page 13.

Air filter cover

12

Frequently Asked Questions

How will it feel when I am breathing with the S8 Series II?

When you first use your S8 Series II, you may feel uncomfortable breathing against the

airflow. This is normal. You will continue to breathe normally while you sleep. The EPR

setting may also improve comfort. Take time to adjust to this new sensation.

What do I do when I want to get up in the night?

If you need to get up during the night, remove your mask and stop therapy. Always

remember to restart therapy and put your mask on when you return to bed.

What do I do if I feel air leaking out of the mask?

The S8 Series II delivers the most effective treatment when the mask is well fitted and

comfortable. Treatment can be affected by leaks, so it is important to eliminate any

leaks that may arise. For example, try repositioning the mask and adjusting the straps.

If you are using a nasal mask, try to keep your mouth closed during treatment. Air leaks

from your mouth can decrease the effectiveness of your treatment. If mouth leaks are

a problem, a full face mask or chin strap may help. Contact your clinician or equipment

supplier for further details.

If you are using a full face mask and you have problems trying to get a comfortable

mask fit, contact your clinician or equipment supplier. You may benefit from a different

size or style of mask.

Anything special I should do before putting the mask on?

Before wearing your mask, wash your face to remove excess facial oils. This will allow

a better fit and prolong the life of the mask cushion.

Do not use moisturizer when wearing a mask.

My mouth feels dry during treatment – what can I do?

You may experience dryness of the nose, mouth, and/or throat during the course of

treatment, especially during winter. In many cases, a humidifier may resolve this

discomfort. Contact your clinician for advice.

My nose is irritated during treatment – what can I do?

You may experience sneezing and/or a runny or blocked nose during the first few

weeks of treatment. In many cases, nasal irritation can be resolved with a humidifier.

Consult your clinician or equipment supplier for advice.

Can I travel with the S8 Series II?

Your S8 Series II has an internal power supply that enables it to operate in other

countries. It will operate on power supplies of 100–240V and 50/60Hz. No special

adjustment is necessary, but you will require an approved power cord for the region in

which you are using the device.

Your S8 Series II device automatically adjusts to changes in altitude up to 8500’

(2591 m).

Please consult the medical services department of your carrier if you intend to use your

S8 Series II on an aircraft. The S8 Series II complies with US FCC Part 15, Class B

requirements.

Note: Do not use your S8 Series II while the aircraft is taking off or landing.

Can I use my S8 Series II if mains (AC) power is not available?

A DC-12 converter is available to connect the S8 Series II to a 12V or 24V DC power

source. Contact your clinician for details.

13Troubleshooting

English

Troubleshooting

If there is a problem, try the following suggestions. If the problem cannot be solved,

contact your equipment supplier or ResMed. Do not attempt to open the device.

No display

Insufficient air delivered from S8 Series II device

Device does not start when you breathe into the mask although your clinician has

enabled SmartStart.

Problem/Possible Cause Solution

Power is not connected. Ensure the power cable is connected and the power

switch (if available) is on.

Ramp or settling time is in use. Wait for air pressure to build up or change ramp or

settling time.

Air filter is dirty. Replace air filter.

Air tubing is kinked or

punctured.

Straighten or replace tubing.

Air tubing not connected

properly.

Check air tubing.

Mask and headgear not

positioned correctly.

Adjust position of mask and headgear.

Cap(s) missing from access

port on mask.

Replace cap(s).

Pressure required for

treatment may have changed.

See your clinician to adjust the pressure.

Power cord not connected

properly.

Connect power cord firmly at both ends.

Power outlet may be faulty. Try another power outlet.

Leak Alert has been enabled

by your clinician; SmartStart

automatically disabled.

Contact your clinician.

Use of a ResMed Full Face

mask.

SmartStart does not work with a full-face mask as the

anti-asphyxia valve will not allow sufficiently high

pressure on exhalation.

Breath not deep enough to

trigger SmartStart.

Take a deep breath in and out through the mask.

Excessive leak. Adjust position of mask and headgear.

Replace caps if missing from ports on mask.

Air tubing may not be connected properly. Connect firmly

at both ends.

Air tubing may be kinked or punctured. Straighten or

replace.

14

Displays error message:

SYSTEM ERRxxxx Call Service! or Exxxx (where

xxxx defines an error)

Displays error message: Check tube!! Key if done

The following message is displayed on the LCD after you try to update settings

or copy data to the Data Card:

Card Error Remove Card

The following message is displayed on the LCD after you try to update settings

or copy data to the Data Card:

Settings Error Remove Card

The following message is NOT displayed on the LCD after you try to update the

settings using the Data Card: Settings Success Remove Card

The following message is displayed on the LCD after you try to update settings

or copy data to the Data Card:

Settings Invalid Remove Card

Problem/Possible Cause Solution

Component failure. Record error number and call service.

Air tubing is loose or blocked. Check that the air tubing is connected securely to your

mask and the air outlet to the front of the S8 Series II.

When you have checked the air tubing, press the Start/

Stop key to restart the device. If this does not clear the

message, disconnect the power cord and then

reconnect it to restart the device.

Data Card is not inserted

correctly.

Check that the patient is inserting the Data Card into the

Data Card module with

the arrow facing up, while the S8

Escape II is switched on and not delivering therapy

(standby mode).

The Data Card is only partly

inserted.

Ensure that the Data Card is inserted into the Data Card

slot as far as it will go.

You may have removed the

Data Card before settings

were copied to the

S8 Escape II.

Reinsert the Data Card and wait for the Settings

Success Remove Card message to appear on the

LCD.

The card is not a ResScan Data

Card.

Only use a ResScan Data Card.

There is a data error on the

Data Card.

Contact your clinician immediately.

The settings were not

updated.

Contact your clinician immediately.

The identification details on

the Data Card do not match

the identification details on

your device.

Contact your clinician immediately.

15Troubleshooting

English

Technical Specifications

The manufacturer reserves the right to change these specifications without notice.

Symbols which appear on the device

Attention, consult accompanying documents; Drip proof; Type CF equipment;

Dangerous voltage; Class II equipment; Start/Stop.

Operating pressure range 4 to 20 cm H

2

O

Dimensions (H x W x D) 4.6" x 6.5" x 5.7" (112 mm x 164 mm x 145 mm)

Weight 3.1 lb (1.4 kg)

Operating Temperature +41°F to +95°F (+5°C to +36°C)

Power Supply • Input range for S8 Series II with HumidAire 3i: 100–240V, 50/60Hz;

110V, 400Hz; 2.5A <140VA (110W) (maximum power consumption).

Instantaneous peak power consumption <340VA.

• Refer to the DC-12 converter instructions for DC ratings. Only use

the ResMed DC-12 converter for DC input.

• Typical power consumption at 20 cm H

2

O is 39VA or 20.7W.

Operating Humidity 10%–95% non-condensing

Storage and Transport

Te m p e r a t u r e

-5°F to -140°F (-20°C to +60°C)

Storage and Transport

Humidity

10%–95% non-condensing

Operating Altitude

Sea level to 8500’ (2591 m)

Electromagnetic

Compatibility

Product complies with all applicable electromagnetic compatibility

requirements (EMC) according to IEC60601-1-2, for residential,

commercial and light industry environments. The electromagnetic

compatibility tables for these ResMed devices can be found on

www.resmed.com, on the Products page under Service and

Support. Click on the PDF file for your device.

Air Filter Two-layered, powder-bonded, polyester non-woven fibre

Air Tubing Flexible plastic, 6’ 6" (2 m)

Air Outlet The 22 mm conical air outlet complies with EN 1281-1

IEC 60601-1 Classifications Class II (double insulation), Type CF

Supplemental Oxygen Recommended maximum supplemental oxygen flow: 4 L/min

Housing Construction

Flame retardant engineering thermoplastic

Noise Level Radiated sound pressure is measured at <24±2 dBA at 10 cm H

2

O and

3’3.36” (1 m) according to ISO17510-1

16

!

GENERAL WARNINGS AND CAUTIONS

A warning alerts you to possible injury.

• Read the entire guide before using the S8 Series II device.

• The advice in this guide should not supersede instructions given by the prescribing

physician.

• A patient should not connect a device to the data communication port unless

instructed to do so by their health care provider or physician. Only ResMed

products are designed to be connected to the data communication port.

Connecting other devices could result in injury, or damage to the S8 Series II

device.

• The S8 Series II device should be used with masks (and connectors)

*

recommended by ResMed, or by a physician or respiratory therapist. A mask should

not be used unless the S8 Series II device is turned on and operating properly. The

vent hole or holes associated with the mask should never be blocked.

Explanation: The S8 Series II device is intended to be used with special masks (or

connectors)* which have vent holes to allow continuous flow of air out of the mask.

When the device is turned on and functioning properly, new air from the device

flushes the exhaled air out through the mask vent holes. However, when the device

is not operating, insufficient fresh air will be provided through the mask, and the

exhaled air may be rebreathed. Rebreathing of exhaled air for longer than several

minutes can, in some circumstances, lead to suffocation. This applies to most

models of CPAP devices.

• In the event of power failure or machine malfunction, remove the mask.

• The S8 Series II device can be set to deliver pressures up to 20 cm H

2

O. In the

unlikely event of certain fault conditions, pressures up to 30 cm H

2

O are possible.

• If oxygen is used with this device, the oxygen flow must be turned off when the

device is not operating. If oxygen has been left on, turn off the device, then wait

30 minutes before turning on the device.

Explanation: When the CPAP device is not in operation and the oxygen flow is left

on, oxygen delivered into the air delivery tubing may accumulate within the CPAP

machine enclosure and create a risk of fire. This applies to most types of CPAP

machines.

• Oxygen supports combustion. Oxygen should not be used while you are smoking

or in the presence of an open flame.

• Always ensure airflow is being generated by the device before the oxygen supply is

turned on.

• Always turn the oxygen supply off before stopping the airflow from the device

Note: At a fixed rate of supplemental oxygen flow, the inhaled oxygen concentration

varies, depending on where the oxygen is introduced, the pressure settings, patient

breathing pattern, mask selection and leak rate.

• Explosion hazard – do not use in the vicinity of flammable anesthetics.

• Do not open the S8 Series II case. There are no user serviceable parts inside.

Repairs and internal servicing should only be performed by an authorized service

agent.

* Ports may be incorporated into the mask or in connectors that are near the mask.

La page charge ...

ResMed S8 Manuel utilisateur

Ce manuel convient également à

ResMed S8 Manuel utilisateur

dans d''autres langues

Documents connexes