Mantis 7921, 7925 Le manuel du propriétaire

Marque: Mantis

Modèle: 7921, 7925

Catégorie: Mini motoculteurs

Taper: Le manuel du propriétaire

MODEL 7925

MAN 430092

Rev. C 6-4-18

MODEL 7921

OPERATOR’S/PARTS MANUAL

Operator’s Manual and Safety Instructions for

Tiller/Cultivator

Motobêche-bineuse

Manuel de l'utilisateur et consignes de

sécurité pour la motobêche-bineuse

MANUEL DE L'UTILISATEUR / PIÈCES DÉTACHÉES

2 Operator’s Manual

IMPORTANT MESSAGE

Thank you for purchasing this Schiller Grounds Care, Inc. product. You have purchased a world class product, one of the best designed and built anywhere.

This machine comes with Operation and Safety instructions, Parts and Service instructions and Engine instructions. The useful life and good service you receive

from this machine depends to a large extent on how well you read and understand these manuals. Treat your machine properly, lubricate and adjust it as instructed,

and it will give you many years of reliable service.

Your safe use of this Schiller Grounds Care, Inc. product is one of our prime design objectives. Many safety features are built in, but we also rely on your good

sense and care to achieve accident-free operation. For best protection, study the manuals thoroughly. Learn the proper operation of all controls. Observe all

safety precautions. Follow all instructions and warnings completely. Do not remove or defeat any safety features. Make sure those who operate this machine

are as well informed and careful in its use as you are.

See a Schiller Grounds Care, Inc. dealer for any service or parts needed. Schiller Grounds Care, Inc. service ensures that you continue to receive the best

results possible from Schiller Grounds Care, Inc. products. You can trust Schiller Grounds Care, Inc. replacement parts because they are manufactured with

the same high precision and quality as the original parts.

Schiller Grounds Care, Inc. designs and builds its equipment to serve many years in a safe and productive manner. For longest life, use this machine only as

directed in the manuals, keep it in good repair and follow safety warnings and instructions. You’ll always be glad you did.

Schiller Grounds Care, Inc.

1028 Street Road

Southampton, PA 18966-4217

PHONE (800) 366-6268 • FAX (215) 956-3855

SAFETY RULES & WARNINGS

Special Safety Information .................................................3

Safety & Warnings ............................................................. 3

Safety Decal Information ...................................................3

Warning Dos ...................................................................... 4

Warning Don’ts ..................................................................5

Engine/Fuel Warning Do’s ................................................. 5

Engine/Fuel Warning Don’ts .............................................. 5

ASSEMBLY ............................................................................6

Lower Handle ....................................................................7

Upper Handle Assembly .................................................... 8

Tines ...............................................................................8-9

Kickstand ........................................................................... 9

FUELING & STARTING

2-Cycle Fueling ................................................................10

2-Cycle Tiller Starting .................................................11-12

OPERATION ....................................................................13-14

TRANSPORT .......................................................................15

STORAGE ............................................................................ 15

MAINTENANCE ..............................................................16-18

TROUBLESHOOTING .........................................................19

MANTIS TILLER ASSEMBLIES ......................................20-24

CONTROL ............................................................................ 25

EPA .......................................................................................26

LIMITED WARRANTY INFORMATION ................BACK PAGE

TABLE OF CONTENTS

Welcome to the World of Mantis Gardening

Here’s your new MANTIS Tiller . . . the lightweight wonder that’s Changing the

Way Americans Garden.

Unlike big tillers, your MANTIS Tiller weighs only 20 lbs. (Model 7921) and 22.5

lbs. (Model 7925). So it lifts easily, handles smoothly, tills and weeds precisely.

And, unlike other small tillers, it features serpentine tines that churn soil to ten

inches deep. It creates a soft, smooth seed bed, even in problem soil.

Once you know how to use your tiller correctly, we guarantee you’ll love it. So rst, please read this manual. It shows, step by

step, how to use your tiller safely.

ATTENTION MANTIS PRODUCT OWNERS!

Get maintenance tips for your Mantis

product on our web site

at www.mantis.com

This Operator’s / Parts Manual is part of the machine. Suppliers of both new and

second-hand machines must make sure that this manual is provided with the machine.

3Contact us at www.mantis.com

You will notice throughout this Operator’s Manual Safety Rules and Important Notes. Make sure you understand and obey these

warnings for your own protection.

I. SPECIAL SAFETY INFORMATION

II. SAFETY & WARNINGS

III. SAFETY DECAL INFORMATION

An important part of the safety system incorporated in this tiller are the warning and information decals found on various parts of

the tiller. These decals must be replaced in time due to abrasion, etc. It is your responsibility to replace these decals when they

become hard to read.

Safety Rules & Warnings

Improper use or care of this tiller or failure to wear

proper protection can result in serious injury.

Read and understand the rules for safe

operation and all instructions in this manual.

Wear hearing and eye protection.

To reduce the potential for accidents, comply

with the safety instructions in this manual.

Failure to comply may result in serious

personal injury, and/or equipment

and property damage.

The engine exhaust from this product contains

chemicals known to the State of California to cause

cancer, birth defects or other reproductive harm.

Attention: This symbol points out our

important safety instructions.

When you see this symbol,

heed it’s warning!! Stay alert!!

P/N 430057P/N 4043

Cutting hazard;

keep feet and

hands away from

rotating tines.

Don’t operate

indoors

Caution: when assembling

the handles, make sure fuel

tank faces operator. This is

the rear of the tiller, refer to

assembly instructions

Incorrect assembly.

Wear ear and

eye Protection.

Do not carry

the tiller in this

position.

Don’t fuel, refuel, or

check fuel while smoking,

or near an open ame or

other ignition source.

Mix unleaded gas

with 2 cycle 50:1 oil.

Read operators manual before

using tiller, or performing any

repair or maintenance. Keep

operators manual in a safe place.

PRODUCT EMISSION DURABILITY

The 300 hour emission durability compliance period

is the time span selected by the manufacturer

certifying the engine emissions output meets

applicable emissions regulations, provided that

approved maintenance procedures are followed as

listed in the Maintenance Section of this manual.

An Emission Control

Label is located on

the engine (This is

an EXAMPLE ONLY,

information on label

varies by engine

FAMILY.)

4 Operator’s Manual

If the tiller is used improperly or safety precautions

are not followed, the users risk serious injury

to themselves and others.

Read and understand this manual before

attempting to operate this tiller.

Operation of this equipment may create sparks

that can start res around dry vegetation. A spark

arrestor is installed. The operator should contact

local re agencies for laws or regulations relating

to re prevention requirements.

IV. WARNINGS - DOS

Read and understand the owner’s manual.

Pay particular attention to all sections

regarding safety.

1. Always keep a rm grip on both handles

while the tines are moving and/or the

engine is running. BE AWARE!! The

tines may coast after throttle trigger is

released. Make sure tines have come to

a complete stop and engine is off before

letting go of the tiller.

2. Always maintain a rm footing and

good balance. Do not overreach while

operating the tiller. Before you start to

use the tiller check the work area for

obstacles that might cause you to lose

your footing, balance or control of the

machine.

3. Thoroughly inspect the area where

equipment is to be used and remove

all objects, which can be thrown by the

machine.

4. Always keep area clear of children,

pets, and bystanders.

5. Always stay alert. Watch what you are

doing and use common sense. Do not

operate unit when fatigued.

6. Always dress properly. Do not wear

loose clothing or jewelry, they might

get caught in moving parts. Use sturdy

gloves. Gloves reduce the transmission

of vibration to your hands. Prolonged

exposure to vibration can cause

numbness and other ailments.

7. While working, always wear substantial

footwear and long trousers. Do not

operate the equipment when barefoot or

wearing open sandals.

8. Always wear ear and eye protection.

Eye protection must meet applicable CE

requirements. To avoid hearing damage,

we recommend hearing protection be

worn whenever using the equipment.

9. To reduce re hazard, keep the

engine, and petrol/gas storage area free

of vegetative material and excessive

grease.

10. Start the engine carefully, according to

the manufacturer’s instructions and with

feet well away from tool(s).

11.

Keep all nuts, bolts and screws tight

to be sure the equipment is in safe

working condition.

12.

Use extreme caution when reversing

or pulling the machine towards you.

13. Work only in daylight or good

articial light.

14. Always be sure of your footing on

slopes.

15. Exercise extreme caution when

changing direction on slopes.

16. Always keep a safe distance between

two or more people when working

together.

17. Always inspect your unit before each

use. Keep all knobs, nuts, bolts and

screws tight to be sure the equipment is

in safe working condition.

18. Always visually inspect to see that

the tools are not worn or damaged.

Before using your tiller, replace worn or

damaged elements and bolts in sets to

preserve balance.

19. Always maintain and examine your

Tiller with care. Follow maintenance

instructions given in manual.

20. Always store tiller in a sheltered area

(a dry place), not accessible to children.

The tiller as well as fuel should not be

stored in a house.

21. Always keep in mind that the operator

or user is responsible for accidents or

hazards occurring to other people or

their property.

5Contact us at www.mantis.com

Handle fuel with care, it is highly ammable. Fueling a hot engine or near an ignition source can

cause a re and result in serious personal injury and/or property damage.

Safety Rules & Warnings

VI. ENGINE/FUEL WARNINGS - DOS

VII. ENGINE/FUEL WARNINGS - DON’TS

Always use fresh gasoline in the fuel mixture.

Stale gasoline can cause damage.

Always store fuel in containers

specically designed for this purpose.

Always add fuel before starting

the engine.

Always replace all fuel tank and

container caps securely.

Always pull starter cord slowly until

resistance is felt to avoid kickback and

prevent arm or hand injury.

Always operate engine with spark

arrestor installed and operating properly.

Stop the engine whenever you leave

the machine and before refueling. Allow

the engine to cool before storing in any

enclosure. Replace worn or damaged

parts for safety.

If the fuel tank needs to be drained, this

should be done outdoors.

Never pick up or carry a machine while

the engine is running.

Don’t fuel, refuel or check fuel while

smoking, or near an open ame or other

ignition source. Stop engine and be sure

it is cool before refueling.

Don’t leave the engine running while the

tiller is unattended. Stop the engine when

carrying out maintenance and cleaning

operations, when changing tools and

when being transported by means other

than under its own power.

Never remove the cap of the fuel tank or

add fuel while the engine is running or

when the engine is hot.

Don’t refuel, start or run this tiller indoors

or in an improperly ventilated area.

Don’t run engine when electrical system

causes spark outside the cylinder. During

periodical checks of the spark plug, keep

plug a safe distance from cylinder to

avoid burning of evaporated fuel from

cylinder.

Don’t check for spark with spark plug

or plug wire removed. Use an approved

tester.

Don’t crank engine with spark plug

removed unless spark plug wire is

disconnected. Sparks can ignite fumes.

Don’t run engine when the odor of gasoline

is present or other explosive conditions exist.

Do not attempt to start the engine if

fuel is spilled, but move the machine

away from the area of spillage and avoid

creating any source of ignition until fuel

vapors have dissipated.

Don’t operate your tiller if there is an

accumulation of debris around the

mufer, and cooling ns. To reduce the

re hazard, keep the engine and fuel

storage area free of vegetative material

and excessive grease.

Don’t touch hot mufers, cylinders

or cooling ns as contact may cause

serious burns.

Don’t change the engine governor

setting or over speed the engine.

Don’t attempt to remove spark plug while

engine is hot. Removing a spark plug

from a hot engine can cause irreparable

damage to the engine and will void your

warranty.

Don’t use starter uids as they will cause

permanent engine damage.

V. WARNINGS - DON’TS

Don’t use tiller with one hand. Keep

both hands on handles with ngers and

thumbs encircling the handles, while

tines are moving, and engine

is running.

Don’t run with the machine, walk.

Don’t work on excessively steep slopes.

Don’t attempt to clear tines while they

are moving. Never try to remove jammed

material before switching the engine off

and making sure the tines have stopped

completely.

Don’t allow children or people unfamiliar

with these instructions to use the

machine. Local regulations can restrict

the age of operator.

Don’t let others operate tiller without

proper training.

Don’t operate while under the inuence

of alcohol or drugs.

Don’t attempt to repair this tiller. Have

repairs made by a qualied dealer or

repairman. See that only original Mantis

parts are used.

Don’t overreach. Keep a good footing at

all times.

Don’t stand in front of tiller when tines

are rotating.

6 Operator’s Manual

T49

T50

Assembly

WHAT COMES IN THE BOX

WHAT YOU WILL NEED

TO ASSEMBLE THE TILLER

Prior to removing the contents and assembling, it is important to:

• Have a clean work area.

• Make sure all necessary

tools are handy.

• You will need two 7/16”

wrenches

• A 3/8” wrench for

kickstand assembly

Improper assembly of this tiller can result in serious injury. Make

sure to follow all instructions carefully. If you have any questions,

contact our factory at 1-800-366-6268 or an authorized Mantis dealer.

Key Qty. Part No. Description

T1 1 Upper Handle Throttle Side Assembly

T2 1 Upper Handle Assembly, Left

T3 2 Lower Handles W/Plug

T4 1 Handle Brace Assembly

T10 1 Plastic Carrying Handle

T21A,

T20, T46

1 Engine Assembly (includes Fender Guard &

Worm Gear Transmission) (model 7921)

T21B,

T20, T46

1 Engine Assembly (includes Fender Guard &

Worm Gear Transmission) (model 7925)

T39/T40 1 Pair Tiller/Cultivator Tines

1 Bag of Hardware Containing

T7 2 Handle Clamps

T9 1 Throttle Clip

T11 2 Bolts (3” long)

T12 2 Knobs

T13 2 Acorn Nuts

T14 4 Lock Nuts

T15 2 Cap Screws

T41 2 Tine Retaining Pins

T42 2 Carriage Bolts

T47 1 Kickstand, Stand Assembly (model 7925)

T48 1 Kickstand, Bracket and Hardware Bag

(model 7925)

Not Shown

1 451 2-Cycle Oil

Picture of Model 7921

Model 7925 Only

Picture of Model 7925

T20

T46

T21B

T40

T41

T10

T15

T39

T20

T46

T21A

T12

T13

T11

T42

Bag Contents

T41

T15

T12

T13

T11

T14

T42

T14

7Contact us at www.mantis.com

LET’S BEGIN

• With the box upright, open the box and remove the

tine box and the loose parts that are at the top of the

tiller box. Do not remove any other parts in the box.

• Lay the box on one side and open the bottom aps.

• Return the box to an upright position (as shown) and

pull the box straight up.

• Leave the engine and throttle handle in the cradle to

assist in the assembly.

• Lay everything out so you can easily identify the

parts (see parts image and list on page 6).

Assembly

NOTE: Some of the photos in this manual do not represent your

tiller engine. They are for assembly purposes only.

• Take the lower handles that

you’ve just put together.

Slide them into the two

recessed channels.

• Make sure you insert them

from the rear of the tiller

(gasoline tank faces the

operator)... so that the bolt

ts along the back of the

housing.

• Slide the second 3-inch

bolt (T11) through the

second set of holes in

the short legs. Add a

lock

nut

(T14)

and tighten

nger tight until you’ve

completed assembly.

LOWER HANDLE ASSEMBLY

• For ease of assembly and

stability it is important that you

keep the engine assembly in its

cardboard cradle.

• Locate recessed channels

below the engine.

NOTE: THE LOCK NUTS ARE STAMPED. FINGER TIGHT IS APPROXIMATELY 1/2 TO 1-1/2 TURNS UNTIL YOU’VE COMPLETED ASSEMBLY.

To identify part numbers see page 6.

• Lay the handle parts within easy

reach. You’ll need one of the

handle clamps (T7) and one of

the lower handles (T3). Note that

the lower handles have a short

leg on one end.

• Fit the handle clamp along the

outside of the short leg. Line

up the holes on the clamp and

the leg.

• Choose one of the two 3-inch

bolts (T11). Slide it through the

rst set of holes — near the

elbow where the lower handle

curves. (Pictures 2 & 3)

• Now slide the other lower

handle onto the 3-inch bolt. Fit

the other

clamp onto the other

handle’s short leg. Add a lock nut

(T14) and tighten nger tight.

(Picture 3)

8 Operator’s Manual

Assembly (Continued)

UPPER HANDLE ASSEMBLY

8 9

• Lift the upper handle until it lines up

with the lower handle.

•

Insert carriage bold (T42) from outside in.

• Screw on knob (T12) and fully tighten

the knob at the pivot point.

• Cap the exposed bolt with an acorn

nut (T13) and tighten with your 7/16”

wrench until snug. Do not over tighten.

• You’ll need the 2 Tines and the

2 retaining pins.

• Remove the unit from the

cardboard cradle and lay the

unit on its side.

• You will notice that one side of the

Tine has a circular hole while the

other has a “D” shaped hole.

TINE ASSEMBLY

1 2 3

• Follow the same steps to install the

other upper handle onto the other

lower handle.

• Use the clip (T9) to secure the throttle

cable and wire in place on the lower

handle.

• Now install the handle brace. Line

it up with the holes on the upper

handles. Then insert a cap screw

(T15) and a lock nut (T14) on either

side.

• Use a wrench to tighten cap screws

and lock nuts.

• Now use wrench to tighten all nuts and

bolts rmly and securely.

• Lightly squeeze the lower

handles (T3) toward one another

so that they line up with the two

smaller holes on the carrying

handle (T10). Then slide the

carrying handle over and down

the lower handles. It will rest

about four to six inches above the

fender.

• Gently pull the lower handles out

to their original position.

• Your Mantis Tiller will look like

this when the lower handle

assembly is complete.

9Contact us at www.mantis.com

Assembly (Continued)

• Your Mantis tiller will look like

this when lower handle assembly

and kickstand is complete.

KICKSTAND ASSEMBLY (MODEL 7925 ONLY)

2 3

IMPORTANT NOTE:

Be sure you have proper throttle movements and that

the throttle cable is not wrapped or twisted around the

handle bar. Hold down the lockout lever, fully squeeze

the throttle trigger and let go. The throttle triangle must

click in both directions. If there is any doubt, remove

air lter and visually check that the throttle triangle hits

both the idle screw and the full open stop. THIS MUST

BE DONE BEFORE STARTING THE ENGINE.

IMPORTANT NOTE:

Before you use your MANTIS Tiller, read the

Safety Rules & Warnings on pages 3-5

IMPORTANT NOTE:

Make sure you have installed the handles properly.

When you stand behind your tiller, holding the handles,

the fender warning label should face you.

Improper Throttle installation can cause tines to rotate unexpectedly.

79257921

TINE ASSEMBLY (Continued)

• Attach the Tine so that the circular hole

slides onto the axle rst.

• When the axle protrudes from the

other side it will line up perfectly

with the “D” shaped hole.

• Slide a retaining pin (T41) through

the hole in the axle to secure the

Tine.

• Repeat steps for the other side.

4 5 6

• Position the kickstand brace just above the

bend of the lower handles.

• Position the kickstand under the lower

handles, line up the holes and thread the

kickstand brace bolts into the kickstand.

•Tighten with the 3/8” wrench.

10 Operator’s Manual

2-CYCLE TILLER FUELING

MIXING FUEL

Use a mixture of 50 parts unleaded

regular gasoline and 1 part two-stroke

MANTIS oil (50:1.) Use branded 89

octane (R+M+2) unleaded gasoline

(maximum 10% ethanol, or 15%

MTBE, no methyl alcohol.)

Here’s how to mix the oil with the gas:

1. Pour 1/2 of the gasoline into a safe container. Do not mix

the fuel and oil in the engine fuel tank.

2. Add 2.6 ounces of two-cycle engine oil to the gasoline and

mix. The bottle is measured exactly to 2.6 ounces. Then

add the rest of the gasoline.

3. Screw the cap onto the gasoline can. Then swirl the can to

blend the oil and gas.

4. Carefully pour the fuel mix into the tiller’s fuel tank. After

putting the fuel tank’s cap back on, wipe up any spilled fuel

from tank and gasoline can.

Need more pre-measured engine oil? You can order it

directly from Mantis or your local authorized Mantis

dealer. Just call toll free 1-800-366-6268 and ask for our

Sales Dept.

IMPORTANT:

Two stroke fuel separates and ages. Do not mix more than

you will use in a month. Using old fuel can cause difcult

starting or engine damage. Shake fuel container to thoroughly

mix fuel before each use.

Remember …

• Never, run your tiller on gasoline alone. This will ruin your

engine and void all warranties.

• Always use a clean gas can and always use unleaded gas.

• Never try to mix the oil and gasoline in the engine fuel tank.

• Always mix oil and gas in the proper proportions: 2.6 ounces

of two-cycle engine oil to one gallon of unleaded gasoline.

IMPORTANT NOTE:

Do Not use old or stale oil/gasoline mixture. Always use

the proper oil/gasoline mixture. If you do not, your engine will

suffer rapid, permanent damage. And you will void the engine

warranty.

2-Cycle Tiller Fueling

Fuel is extremely ammable. Handle it with

care. Keep away from ignition sources. Do not

smoke while fueling your equipment

Do not operate the engine in a conned

space where dangerous carbon monoxide

fumes can collect.

Avoid accidental blade engagement.

Do not squeeze the throttle trigger when starting. Main-

tain proper idle speed adjustment (2500-3100 rpm)

WARNING • DANGER

ALTERNATIVE FUELS, SUCH AS E-15 (15% ETHANOL), E-85 (85% ETHANOL) OR ANY FUELS NOT MEETING ECHO REQUIREMENTS ARE NOT APPROVED FOR USE IN

ECHO 2-STROKE GASOLINE ENGINES. USE OF ALTERNATIVE FUELS MAY CAUSE PERFORMANCE PROBLEMS, LOSS OF POWER, OVERHEATING, FUEL VAPOR LOCK

AND UNINTENDED MACHINE OPERATION, INCLUDING, BUT NOT LIMITED TO, IMPROPER CLUTCH ENGAGEMENT. ALTERNATIVE FUELS MAY ALSO CAUSE PREMATURE

DETERIORATION OF FUEL LINES, GASKETS, CARBURETORS AND OTHER ENGINE COMPONENTS.

! !

2.6 oz. bottle of Mantis 50:1

2-cycle engine oil

11Contact us at www.mantis.com

Switch

Picture 1 Picture 2

Choke

OFF ON

FOR MODEL 7921:

Pull the recoil starter handle/rope

(Picture 4A) with a controlled

motion until resistance is felt.

Then give the cord a few brisk

pulls until the engine res. During

cold starting, you may need to

try three or four times before

the engine res. Do not pull the

rope out to end stop and do not

let it snap back into the starter

housing.

FOR MODEL 7925 (Fast starting engine option):

Fast starting system signicantly reduces the effort required

to start the engine. Energy is stored in the starter spring

each time the handle/rope is pulled.

Slowly pull the recoil starter

handle/rope (Picture 4B) to wind

up the spring. You will hear light

clicking and then the sound of the

released spring. Generally during

cold starting, you may need two to

four light pulls before the engine

res.

7. Push the choke button in, all the way, to open the choke.

8. Then pull the starter cord again until engine starts and

runs.

Let the engine warm up two to three minutes before using

NOTE: If engine does not start with choke in “Run” position

after 5 engine engagements, repeat Cold Start instructions.

WARM STARTING

• To start a warm engine, follow the same procedure. The

only exception is that you can leave the choke button in

and you don’t have to pump the primer bulb.

• Before using the tiller, let the engine idle for a minute to

warm up. Before shutting it down, let the engine idle for

two to three minutes to cool down.

2-Cycle Tiller Starting

Never use starting uids as they will cause permanent engine damage. Using them will void the warranty.

Before you use the tiller, read the Safety & Warning rules on pages 5.

2-CYCLE TILLER STARTING

1. Fill the fuel tank with the proper oil/gasoline mixture.

(See previous section.)

2. Hand tighten the gasoline cap just until it’s snug.

3. Place the O/I switch into the I “start/on” position.

(Picture 1)

4. Pull the choke button all the way out, to completely

close the choke. (Picture 2)

5. Locate the purge bulb on the upper right of the

engine, in front of the fuel tank. (See Picture 3) It

sends fuel into the carburetor, for easy starting.

Press the purge bulb until you see fuel ow through

the clear fuel return line. Since you’re starting “cold,”

you may need to press six to eight times. As soon

as fuel starts owing through the clear fuel line, stop

pressing!

NOTE: Don’t press the throttle trigger

during the starting of the engine.

6. Recoil pull starting (Different for each model)

NOTE: DO NOT PULL THE CORD MORE THEN 4 TIMES WHEN THE CHOKE IS CLOSED. OVER PULLING MAY

CAUSE ENGINE FLOODING!

Bear in mind that, when the engine res, it only coughs or sputters, and will not run on choke.

Picture 3

Picture 4A

Picture 4B

12 Operator’s Manual

WHAT TO DO JUST IN CASE

If you follow the normal starting procedure, you should have no problem starting your

tiller. But, just in case you do have problems, here’s what to do.

Make sure the O/I switch is on “I” (start).You’d be surprised how many people

forget to push the switch into the “I” (start)

position.

If the switch was on “O” (stop) when you

pulled the cord, you may have ooded

the engine.

• First, examine the spark plug. Use the

special wrench that comes with our

optional MANTIS Handy Item Kit (Item

#8444) or a 3/4 inch spark plug wrench.

(Picture 1)

• Remove the cap over the spark plug.

• Unscrew the spark plug. (Picture 2)

STARTING A FLOODED ENGINE

If the end of the spark plug is wet, the engine may be ooded. Make sure the switch

is in the “O” (stop) position, disconnect spark plug wire and remove plug. Use a

paper towel or a clean rag to dry the spark plug, then, with the spark plug out of

the engine, pull the starter cord several times. Next, replace the spark plug.

Use the wrench to tighten it and replace the cap. Then, put the switch in the “I” (start)

position and pull the choke button out. Pull the starter cord three or four times until the

engine coughs or sputters. Open the choke (push the choke button in) and pull the

cord a few times. The engine should start and run.

FUEL LINES CHECK

If the end of the spark plug is dry, check to see if the fuel line is blocked. First loosen

the fuel cap to relieve the pressure in the tank. The fuel line runs from the fuel tank to

the carburetor. Pull it off at the carburetor end. Fuel should drip slowly from the line.

Wipe off any excess or spilled fuel.

If fuel does not drip from the line, check the line for any bends or pinches. (Picture

3). Kinks in the line restrict the ow of fuel to the engine. Just straighten out the line.

Reconnect. Then follow the normal starting procedure.

If fuel drips too freely, the line may be disconnected from the fuel lter. You’ll nd the

fuel lter inside the fuel tank. Just re-attach the line to the lter, and put the lter back

in the tank. Then follow the normal starting procedure.

If you follow the normal

starting procedure, you should

have no problem starting your

tiller. But, just in case you do

have problems, here’s what to do.

Make sure the start/stop

switch is on “start.” You’d be

surprised how many people

forget to push the switch into the

“start” position.

If the switch was on “stop”

when you pulled the cord, you

may have flooded the engine.

•First, examine the spark plug.

Use the special wrench that

comes with our optional

MANTIS Handy Item Kit (Item

#1422) or a 3/4 inch spark plug

wrench. (Picture 1)

•Remove the cap over the spark

plug.

•Unscrew the spark plug.

(Picture 2)

Starting a Flooded

Engine

1. If the end of the spark plug

is wet, the engine may be

flooded. Make sure the switch

is in the stop position,

disconnect spark plug wire and

remove plug. Use a paper towel

or a clean rag to dry the spark

plug, then, with the spark plug

out of the engine, pull the

starter cord several times.

Next, replace the spark plug. Use

the wrench to tighten it and

replace the cap. Next, put the

switch in the start position and

pull the choke button out. Pull

the starter cord three or four

times until the engine coughs or

sputters. Open the choke (push

the choke button in) and pull

the cord a few times. The engine

should start and run.

2. If the end of the spark plug

is dry, check to see if the fuel

line is blocked. First loosen the

fuel cap to relieve pressure in the

tank. The fuel line runs from

the fuel tank to the carburetor.

Pull it off at the carburetor end.

Fuel should drip slowly from the

line. Wipe off any excess or

spilled fuel.

If fuel does not drip from the

line, check the line for any bends

or pinches. (Picture 3). Kinks in

the line restrict the flow of fuel

to the engine. Just straighten out

the line. Reconnect. Then follow

the normal starting procedure.

If fuel drips too freely, the line

may be disconnected from the

fuel filter. You’ll find the fuel

filter inside the fuel tank. Just re-

attach the line to the filter, and

put the filter back in the tank.

Then follow the normal starting

procedure.

Here’s Another Way to

Start your MANTIS

Tiller

If you follow the steps above

and your engine still won’t start,

try this:

1. Push the switch to “start.”

WARNING

MAKE SURE THE START/STOP

SWITCH IS IN THE

STOP POSITION.

KEEP PLUG WIRE AWAY

FROM ENGINE TO AVOID

UNINTENTIONAL SPARK.

IMPORTANT NOTE:

To avoid possible damage

to the threads, do not try

to remove the plug from a

hot aluminum cylinder

head.

WHAT TO DO JUST IN CASE

! !

Picture 1

Picture 2

Picture 3

IMPORTANT NOTE:

To avoid possible damage to the

threads, do not try to remove the plug

from a hot aluminum cylinder head.

WARNING

MAKE SURE THE START/STOP SWITCH IS IN THE

STOP POSITION. KEEP PLUG WIRE AWAY FROM

ENGINE TO AVOID UNINTENTIONAL SPARK.

! !

2-Cycle Tiller Starting (Continued)

13Contact us at www.mantis.com

2-Cycle Tiller Operation

If engine does not stop when switch is put in the stop position, release the throttle, allow engine to idle. Put the tiller

down, and slide the choke lever to the cold start (closed) position. Have product serviced before using.

Read the instructions carefully. Be

familiar with the controls and the

proper use of the equipment.

A SPECIAL FEATURE

(With the idle set properly and the

engine running)

Even when the engine is running, the

tines won’t turn unless you squeeze

the throttle trigger on the handlebars.

When you release the throttle trigger,

the tines will stop

A TIP FOR EXTENDING

YOUR ENGINE’S LIFE

After you start the engine, let your

tiller warm up for two to three

minutes before you use it. Then,

before you put your tiller away, let it

idle for a minute to give the engine a

chance to cool down.

OPERATION

With engine running, and both

hands on the handles, hold down

the throttle lockout trigger (Figure

1), then squeeze the throttle trigger

gradually to increase the engine

speed and engage the tines.

NOTE: This step must be repeated

each time your tiller trigger is

released.

NOW YOU’RE READY TO USE

YOUR MANTIS TILLER.

If you’ve seen other tillers, your MANTIS

Tiller may surprise you. It tills best when

you pull it backward! You see, when you

pull your MANTIS Tiller backward, you

give extra resistance to the tines, so they

dig deeper. (Figure 2)

In addition, when you go backward,

you erase your footprints. So your soil

stays light and uffy. With other tillers,

by contrast, you walk right over the soil

you’ve just tilled, packing it down, so it’s

less plantable.

RUN YOUR MANTIS TILLER

LIKE A VACUUM CLEANER

Place your Tiller at the head of the row

or area you want to till. Start it up. Then

use an easy rocking motion. First, pull

your Tiller backward. Then use an easy

rocking motion. Again, pull your Tiller

backward. Then, let it move forward just

a little bit. Then pull it backward again.

This will help you till deeper.

Keep repeating these steps until you’ve

tilled an entire row. Start again on the

next row. It’s much like running a vacuum

cleaner! (Figure 3)

You Can Even Control Depth.

For Deeper Tilling:

Move your Tiller slowly back and forth, as

you would a vacuum cleaner. Work the

same area over and over until you’ve dug

to your desired depth. (Figure 4)

For Shallow Tilling:

Switch the tines to the cultivating

position. (See page 14 to learn how.)

Then move your Tiller quickly over your

soil surface.

For Big Weeds or Tough Roots:

Let your Tiller rock back and forth over

the tough spot, until the tines slice

through the weed or root.

Your MANTIS Tiller Handles Special

Tilling Projects:

Want to turn part of your lawn into a

colorful ower border? Your MANTIS

Tiller makes it easy! Just run your Tiller

back and forth until the sod begins to

break up. Then continue tilling. Your Tiller

will chop the clumps of sod until they’re

ne. Then, it will work them into the soil.

Pretty soon, you’ll have a soft, fresh

planting bed.

Figure 1

WARNING

ALWAYS MAKE SURE THE HANDLE KNOBS ARE

SECURE BEFORE STARTING YOUR MANTIS TILLER.

! !

Figure 2 Figure 3 Figure 4

14 Operator’s Manual

YOUR MANTIS TILLER MAKES

WEEDING A PLEASURE!

As a tiller, your MANTIS Tiller works the soil

down to 10” (25.4 cm) deep. But, as a cultivator,

it gently cultivates the surface, only 2” to 3” (5.09

cm to 7.62 cm) deep.

First, you must switch the tines to the weeding,

cultivating position. This takes less than a

minute.

Then, your MANTIS Tiller’s sharp “tine teeth” will

slice up those pesky weeds, burying them as you

go along. And, since the tines in this position

won’t dig too deep, they won’t hurt your plants’

precious root systems.

The result? Your Tiller will cut your weeding time

in half, and turn a tiresome chore into a pleasure.

HOW TO SWITCH FROM TILLING TO

CULTIVATING POSITION

1. Make sure your Tiller is off.

2. Remove the retaining pins from the tines.

3. Remove the tines from the axle.

4. Place the right-side tine onto the left-side axle.

Place the left side tine onto the right-side axle.

The “D” hole should be to the outside.

5. Reinsert the pins. (Figure 1)

2-Cycle Tiller Operation (Continued)

The operator of this tiller is responsible for

accidents or hazards occurring to himself,

other people or their property.

If your tines get jammed or entangled, shut off the

engine at once. Remove the obstruction while the

engine is off. Never try to remove an obstruction while

the engine is running. Serious injury can result.

To set them for tilling, attach the tines

so the points of the blades face forward

- away from the operator. The tines’

points will contact the ground rst.

For cultivating, reverse the tines

so that the points of the tines face

backward - toward the operator. Now

the long at part of the tine’s blade

will contact the ground rst.

Tilling Cultivating

Figure 1

15Contact us at www.mantis.com

Each fall, or before you store your

Mantis Tiller for any long period, be sure

to take these measures:

1. Do not store your Tiller with fuel still in

it. Even under ideal conditions, stored

fuel containing ethanol or MTBE can

start to go stale in 30 days. And, since

stale fuel has a high gum content, it

can clog the carburetor, this, in turn,

will restrict fuel ow. Therefore, when

you’re ready to store your Tiller,

or will not be using it for more

than 2 weeks, drain the fuel tank

completely.

2. Next, restart the engine to make

sure no fuel is left in the carburetor.

Then, run the engine until it stops.

This will prevent gum deposits,

forming inside of the carburetor and

possible engine damage.

3. Disconnect spark plug wire and

remove the spark plug. Slowly pull the

starter cord once.

4. Inspect the spark plug, and if

necessary, clean it. If you need to

replace it, buy a NGR-BPM8Y.

Pour about a teaspoon of clean, air-

cooled, two-cycle oil through the spark-

plug hole into the combustion chamber.

Leaving the spark plug out slowly pull

the starter cord two or three times to

coat the inside of the cylinder wall.

5. Install the spark plug, but leave the

spark plug wire disconnected.

6. Wipe the tines with oil or spray them

with WD-40, to prevent rusting.

7. Clean or replace the air lter.

8. Check or replace fuel lter.

9. Check the grease level in the worm

gear housing. Add grease if needed.

10. Store your Tiller in an upright position

in a clean, dry place. You can store

with the handles in an extended

position or folded down.

To fold the handles down, simply

loosen the lower 2-pronged knobs

until you can pivot the upper handles

down. (Figure 2)

Or it can be hung using the handle

brace.

11. Do you have fuel left over from last

season? Dispose of it properly. Buy

fresh oil and gasoline next season.

12. Remove Tilling Tines or attachments

and lightly oil tine shaft at least once

a year.

2-Cycle Tiller Transportation & Storage

Never store the equipment

with Fuel in the tank or in

an area where fumes may

accumulate and breach an

open ame or spark

2-CYCLE TILLER TRANSPORTATION

Transporting your Tiller is easy. It’s light enough and easy

to carry using the carrying handle as seen in Figure 1.

Or, with it running, you can walk it by gently squeezing

the throttle until it moves at a comfortable pace.

Your tiller is easily transported in the back of a car or

truck. Be sure to empty the fuel tank (This is crucial)!

Then stow your tiller in the trunk of your car or truck.

TILLER STORAGE

Figure 1

Figure 2

Picture 1

WARNING

NEVER CARRY YOUR TILLER AS THE PERSON

IN PICTURE 1 IS DOING. IF YOU DO, YOU WILL

SUFFER SERIOUS INJURY.

! !

16 Operator’s Manual

HOW TO CHECK, CLEAN AND CHANGE THE AIR FILTER

1. Loosen the wing nut on the side of the air-cleaner cover. (Picture 1)

2. Take off the cover. Make sure to clear the choke button.

3. The air lter is the pad on the inside of the air-cleaner cover. Check whether it is

soiled or moist.

4. If the air lter needs cleaning or no longer ts properly, remove it. Just lift an edge

carefully and “peel” it out. (Picture 2)

5. Use a brush to remove debris from the pad.

6. If the air lter is so dirty that it won’t come clean, you must replace it or severe

engine damage will occur. Order a new one directly from our Customer Service Dept.

Call 1-800-366-6268.

7. Insert your clean lter inside the air-cleaner cover.

IMPORTANT! Make sure lter is “seated” properly in the cover. The lter must t

snugly inside the rim that holds the lter in place.

Installing the lter incorrectly will cause engine damage and void the warranty. Fit the

cover back over the air cleaner. (Again, make sure to clear the choke button.)

8. Tighten the wing nut to secure the cover.

2-Cycle Tiller Maintenance

Fuel Filter

FUEL FILTER REPLACEMENT

The fuel lter should be replaced every year. Open the fuel cap and using the cap

retainer you can remove the fuel intake line. The lter is at the end.

Hold the fuel line and work the lter out. Then just push the new one back into the tube

making sure the clamping wire is up high enough to engage with the stem of the lter.

Picture 2

Picture 1

Air Filter

Note:

Please check the lip on the Air Cleaner Cover. If the lip is chipped or cracked,

it should be replaced. This will prevent dirt from being ingested through the

carburetor into the inside of the engine.

17Contact us at www.mantis.com

WHAT TO DO IF YOUR ENGINE

IDLES TOO HIGH

What if your engine runs too fast … or if the

tines turn the instant you start the Tiller?

You may need to adjust the idle screw right

below the H and L screws. Gently turn

it counter-clockwise. You’ll know you’ve

adjusted it correctly when the axles do not

turn at low idle.

WHAT TO DO IF YOUR ENGINE

RUNS “ROUGH” CARBURATOR

ADJUSTMENT

If your engine runs “rough” or stalls, you

may need to adjust the carburetor and idle

screws.

If you remove the air-cleaner cover, you’ll

see the two carburetor, adjustment

screws

next to the choke button. (Picture 1)

The “RED” screw is the HIGH-speed

adjustment…The “WHITE” screw is the low

speed adjustment.

First, remove the tines from the axle. Then

start engine. Let it run for two to three

minutes. “FLASH” the choke several times

during the warm-up by closing and opening

it while engine runs in order to clear any air

from the Fuel system.

Then stop the engine after it reaches

operating temperature.

Now, turn the RED, high-speed screw

counter-clockwise all the way to stop…

Then turn the WHITE, low speed screw

halfway between the counter-clockwise and

clockwise stop positions.

Now restart the engine to nish the

carburetor adjustment.

Run the engine at full speed two or three

seconds to clear out any excess fuel. Then

return to idle.

Now, accelerate the engine to full throttle

several times to check for a smooth

transition from idle to high speed.

If the engine hesitates turn the WHITE, low-

speed screw counter-clockwise one-eighth

of a turn. Then accelerate the engine.

Repeat the adjustment until you get a

smooth transition to high speed.

Picture 1

CLEANING THE MUFFLER SCREEN

1. Take out the spark plug.

2. Remove the red cylinder cover,

(#D1) which is held on by 2 phillips-

head screws, (#D2) and 1 hex-head

screw, (#D3) which you will need an

allen wrench to remove.

3. You will see the metal exhaust

guide, held on by 3 more phillips-head

screws. (#C1) Remove the exhaust

guide.

4. Behind the exhaust guide (#C2) will

be the mufer gasket (#C3) and mufer

screen (#C4). The screen sits under

the gasket.

5. If the screen (#C4) is clogged with

deposits, it needs to be cleaned.

Use carburetor cleaner, and any brush

that is not metal. Brush the screen until

you are able to see through it.

6. If the screen remains plugged

after attempts at cleaning, it must be

replaced.

99922200869 - 8 - REVISED 10/16/13

Table of Contents Part Number Index

SV-5C/2 Engine Engine Cover, Fancase, Starter

2-Cycle Tiller Maintenance

WARNING • DANGER

REMOVE TINES BEFORE STARTING ENGINE AND

MAKING ADJUSTMENTS

! !

WARNING • DANGER

DO NOT USE GASOLINE OR OTHER

FLAMMABLE SUBSTANCE

! !

HIGH ALTITUDE OPERATION

This engine has been factory adjusted to

maintain satisfactory starting, emission, and

durability performance up to 1,100 feet (96,0

kPa and above) mean sea level (MSL). To

maintain proper engine operation above

1,100 feet (96,0 kPa and above) MSL the

carburetor may need to be adjusted by an

authorized ECHO service dealer.

IMPORTANT

If the engine is adjusted for operation above

1,100 feet MSL, the carburetor must be re-

adjusted when operating the engine below

1,100 feet MSL, otherwise severe engine

damage can result.

EXHAUST PORT/MUFFLER CLEANING

Tools required: 4mm Hex wrench, Wood or

plastic scraper

Parts Required: As needed: Heat Shield

1. Remove spark plug lead from spark plug,

and remove engine cover (2 screws).

2. Place piston at top dead center. Remove

mufer (A) and heat shield (B).

3. Use a wood or plastic scraping tool to

clean deposits from cylinder exhaust port.

IMPORTANT

Never use a metal tool to scrape carbon from

the exhaust port. Do not scratch the cylinder

or piston when cleaning the exhaust port.

Do not allow carbon particles to enter the

cylinder.

4. Inspect heat shield, and replace if

damaged.

5. Install heat shield and mufer.

6. Tighten mufer mounting bolts (or nuts) to

80-95 in•lbf (90-110 kgf•cm).

7. Start engine, and warm to operating

temperature.

8. Stop engine, and re-tighten mounting bolts

(or nuts) to specications.

9. Install engine cover and attach spark plug

lead.

18 Operator’s Manual

Check the transmission grease level after the rst

10 hours of use, then check yearly.

With the tines off, remove the transmission plate

(Figure 3) and gasket to see if the grease level is up

to the plate ange (Figure 4). If it is not, you will need

to add lithium zero or lithium one grease.

Wipe off any excess grease, replace the transmission

gasket and plate.

At some point, you may nd that the

tines won’t turn when you press the

throttle. This may mean the engine isn’t

sitting all the way down on the worm

gear housing.

Perhaps you’ve been using your Tiller

for several years. Or perhaps you’ve

removed the engine for use with our

hedge trimmer attachment, then replaced

it. In either case, the ange bolt may

have come loose and lifted the

engine up.

If this happened you’ll notice a gap

between the bottom of the engine clutch

case and the top of the worm gear

housing. (Figure 1)

To x this, loosen the ange bolt. Take

the engine off the worm gear housing.

Notice the hex head on top of the drive

shaft . Inside the clutch case, you’ll nd

the clutch drum. Make sure the hex head

lines up with the clutch drum inside the

clutch case.

Then put the engine back on the

worm gear housing. Make sure the

plastic carrying handle is not under the

fuel tank.

If you’ve followed these steps properly,

there will be no gap between the clutch

case and the worm gear housing.

(Figure 2) Make sure you tighten the

ange bolt!

Note how the engine doesn’t sit all

the way down on the transmission.

HOW TO RESEAT THE FLANGE

TRANSMISSION CARE

Note how the engine sits all the

way down on the transmission.

2-Cycle Tiller Maintenance

Figure 3

Figure 4

Figure 1

Figure 2

19Contact us at www.mantis.com

Troubleshooting

Problem Cause Remedy

1. Tines don’t turn when throttle

is depressed

• Engine is not seated properly on the gear housing. • Re-install engine following the instructions on

page 18 “How to reseat the flange”.

2. Engine fails to start

• O/I switch is in “O” position.

• No fuel in tank.

• Fuel strainer clogged.

• Fuel line clogged.

• Spark plug shorted or fouled.

• Spark plug is broken (cracked porcelain or

electrodes broken)

• Ignition lead wire shorted, broken or disconnected from

spark plug.

• Ignition inoperative

• Move switch to “I”

• Fill Tank.

• Replace Strainer.

• Clean fuel line.

• Install new spark plug.

• Replace spark plug.

• Replace lead wire or attach to spark plug.

• Contact your local authorized dealer.

3. Engine hard to start. • Water in gasoline or stale fuel mixture.

• Too much oil in fuel mixture.

• Engine under or over choked.

• Carburetor out of adjustment.

• Gasket leaks (carburetor or cylinder base gasket).

• Weak spark at spark plug.

• Drain entire system and refill with fresh fuel.

• Drain and refill with correct mixture.

• If flooded by over choking, proceed according

to instructions in operation section. If under

choked, move choke lever to closed position

and crank two or three times.

• See “Carburetor Adjustment.”

• Replace gaskets.

• Contact your local authorized dealer.

4. Engine continuously floods. • Fuel tank vent line is not in an upright position. • Return the fuel tank vent line to the upright

position and place it under the cylinder cover in

the small “pocket” in the cylinder cover

5. There is black smoke coming from

exhaust

• The muffler screen is clogged • Clean carbon from muffler screen (page 17)

6. Engine misses. • Dirt in fuel line or carburetor.

• Carburetor improperly adjusted.

• Spark plug fouled, broken or incorrect

gap setting.

• Weak or intermittent spark at spark plug.

• Remove and clean.

• See “Carburetor Adjustment” (page 17)

• Clean or replace spark plug - set

gap to .024-.028

in. (0.6-0.7 mm)

• Contact your local authorized dealer.

7. Engine lacks power. • Air filter clogged.

• Carburetor out of adjustment.

• Muffler clogged.

• Clogged exhaust ports.

• Spark Arrestor Clogged.

• Poor compression.

• Clean or replace air filter.

• See “Carburetor Adjustment”.

• Clean carbon from muffler.

• Remove muffler, rotate engine until the piston

is at top of cylinder. With a wooden scraper

or blunt tool, remove all carbon from exhaust

ports. Be careful not to scratch or damage

piston or cylinder walls. Blow out all loose

carbon with compressed air. Install muffler and

gasket.

• Clean muffler screen (page 17)

• Contact your local authorized dealer.

8. Engine overheats. • Insufficient oil in fuel mixture

• Air flow obstructed

• Mix fuel as described in starting instructions.

• Clean flywheel cylinder fins and screen.

9. Engine noisy or knocking. • Spark plug in incorrect heat range.

• Bearings, piston ring or cylinder walls are worn.

• Replace with plugs specified for engine.

• Contact your local authorized dealer.

10. Engine stalls under load. • Carburetor adjustment too “lean.”

• Engine overheats.

• See “Carburetor Adjustment.” (page 17)

• Remove dust and dirt from between fins.

20 Operator’s Manual

2-Cycle Tiller Assembly

T46

T25

T45

T26

T40

T31

T32

T36

T38

T41

T33

T35

T36

T34

T37

T38

T29

T27

T28

T30

T35

T24

T23

T39

T41

T12

T16

T17

T22*

T20

T42

T13

T42

T18

T44

T21A

T11

T12

T14

T43

T14

T15

T14

T15

T10

T19

MODEL NO. 7925 ONLY

T47

T48

T21B

MODEL

NO. 7925

La page charge ...

Mantis 7921, 7925 Le manuel du propriétaire

Marque: Mantis

Modèle: 7921, 7925

Catégorie: Mini motoculteurs

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Mantis 7921, 7925 Owner's manual

Mantis 7921, 7925 Le manuel du propriétaire

Mantis 7921, 7925 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents