RIDGID R4040S-FT3500-FT3508-FT7007-FT7001 Manuel utilisateur

Cette scie a été conçue et fabriquée conformément aux

strictes normes de fiabilité, simplicité d’emploi et sécurité

d’utilisation. Correctement entretenu, cet outil vous donnera

des années de fonctionnement robuste et sans problème.

AVERTISSEMENT :

Pour réduire les risques de blessures, l’utilisateur

doit lire et veiller à bien comprendre le manuel

d’utilisation avant d’employer ce produit.

Su sierra ha sido diseñado y fabricado de conformidad con

nuestras estrictas normas para brindar fiabilidad, facilidad de

uso y seguridad para el operador. Con el debido cuidado, le

brindará muchos años de sólido funcionamiento y sin problemas.

ADVERTENCIA:

Para reducir el riesgo de lesiones, el usuario debe

leer y comprender el manual del operador antes

de usar este producto.

CONSERVER CE MANUEL POUR

FUTURE RÉFÉRENCE

GUARDE ESTE MANUAL PARA

FUTURAS CONSULTAS

SAVE THIS MANUAL FOR FUTURE REFERENCE

Your saw has been engineered and manufactured to our high standard for dependability, ease of operation, and operator

safety. When properly cared for, it will give you years of rugged, trouble-free performance.

WARNING:

To reduce the risk of injury, the user must read and understand the operator’s manual before using this product.

OPERATOR’S MANUAL

MANUEL D’UTILISATION

MANUAL DEL OPERADOR

8 in. TILE AND PAVER SAW WITH LASER

SCIE À CARREAUX ET PAVES SOUS EAU

DE 203 mm (8 po) AVEC LASER

SIERRA PARA LOSAS Y PAVIMENTO

DE 203 mm (8 pulg.) CON LÁSER

R4040/R40401

To register your RIDGID product, please visit: http://register.RIDGID.com

Pour enregistrer votre produit de RIDGID, s’il vous plaît la visite: http://register.RIDGID.com

Para registrar su producto de RIDGID, por favor visita: http://register.RIDGID.com

2 — English

 Introduction ......................................................................................................................................................................2

Introduction / Introducción

 General Safety Rules .....................................................................................................................................................3-4

Règles de sécurité générales / Reglas de seguridad generales

 Specific Safety Rules ........................................................................................................................................................ 4

Règles de sécurité particulières / Reglas de seguridad específicas

Symbols ............................................................................................................................................................................ 5

Symboles / Símbolos

Electrical ........................................................................................................................................................................6-7

Caractéristiques électriques / Aspectos eléctricos

 Features .........................................................................................................................................................................8-9

Caractéristiques / Características

 Tools Needed .................................................................................................................................................................... 9

Outils nécessaires / Herramientas necesarias

 Loose Parts .................................................................................................................................................................... 10

Pièces détachées / Piezas sueltas

 Assembly ...................................................................................................................................................................11-17

Assemblage / Armado

 Operation ................................................................................................................................................................... 17-24

Utilisation / Funcionamiento

 Adjustments ...............................................................................................................................................................25-28

Réglages / Ajustes

 Maintenance ..............................................................................................................................................................29-30

Entretien / Mantenimiento

 Warranty ......................................................................................................................................................................... 31

Garantie / Garantía

 Parts Ordering and Service ...............................................................................................................................Back page

Commande de pièces et réparation / Pedidos de piezas y servicio

INTRODUCTION

INTRODUCTION / INTRODUCCIÓN

This product has many features for making its use more pleasant and enjoyable. Safety, performance, and dependability

have been given top priority in the design of this product making it easy to maintain and operate.

* * *

Ce produit offre de nombreuses fonctions destinées à rendre son utilisation plus plaisante et satisfaisante. Lors de la

conception de ce produit, l’accent a été mis sur la sécurité, les performances et la fiabilité, afin d’en faire un outil facile à

utiliser et à entretenir.

* * *

Este producto ofrece numerosas características para hacer más agradable y placentero su uso. En el diseño de este producto

se ha conferido prioridad a la seguridad, el desempeño y la fiabilidad, por lo cual se facilita su manejo y mantenimiento.

TABLE OF CONTENTS

TABLE DES MATIÈRES / ÌNDICE DE CONTENIDO

3 — English

GENERAL SAFETY RULES

WARNING:

Read and understand all instructions. Failure to

follow all instructions listed below, may result in

electric shock, fire and/or serious personal injury.

READ ALL INSTRUCTIONS

 KNOW YOUR POWER TOOL. Read the operator’s manual

carefully. Learn the saw’s applications and limitations as

well as the specific potential hazards related to this tool.

 GUARD AGAINST ELECTRICAL SHOCK BY

PREVENTING BODY CONTACT WITH GROUNDED

SURFACES. For example, pipes, radiators, ranges,

refrigerator enclosures.

 KEEP GUARDS IN PLACE and in good working order.

 REMOVE ADJUSTING KEYS AND WRENCHES. Form

habit of checking to see that keys and adjusting wrenches

are removed from tool before turning it on.

 KEEP WORK AREA CLEAN. Cluttered areas and benches

invite accidents. DO NOT leave tools or pieces of tile on

the saw while it is in operation.

 DO NOT USE IN DANGEROUS ENVIRONMENTS. Do

not use power tools in damp or wet locations or expose

to rain. Keep the work area well lit.

 KEEP CHILDREN AND VISITORS AWAY. All visitors

should wear safety glasses and be kept a safe distance

from work area. Do not let visitors contact tool or extension

cord while operating.

 MAKE WORKSHOP CHILDPROOF with padlocks and

master switches, or by removing starter keys.

 DON’T FORCE TOOL. It will do the job better and safer

at the feed rate for which it was designed.

 USE RIGHT TOOL. Don’t force the tool or attachment to

do a job it was not designed for. Don’t use it for a purpose

not intended.

 USE THE PROPER EXTENSION CORD. Make sure

your extension cord is in good condition. Use only a

cord heavy enough to carry the current your product

will draw. An undersized cord will cause a drop in line

voltage resulting in loss of power and overheating. A wire

gauge size (A.W.G.) of at least 14 is recommended for an

extension cord 25 feet or less in length. If in doubt, use

the next heavier gauge. The smaller the gauge number,

the heavier the cord.

 DRESS PROPERLY. Do not wear loose clothing, gloves,

neckties, or jewelry. They can get caught and draw you

into moving parts. Rubber gloves and nonskid footwear

(rubber soled boots) are recommended when working

outdoors. Also wear protective hair covering to contain

long hair.

 ALWAYS WEAR EYE PROTECTION WITH SIDE

SHIELDS WHICH IS MARKED TO COMPLY WITH ANSI

Z87.1 WHEN USING THIS PRODUCT.

 SECURE WORK. Use clamps or a vise to hold work when

practical, it is safer than using your hand and frees both

hands to operate the tool.

 DON’T OVERREACH. Keep proper footing and balance

at all times.

 MAINTAIN TOOLS WITH CARE. Keep tools sharp and

clean for better and safer performance. Follow instructions

for lubricating and changing accessories.

 DISCONNECT TOOLS. When not in use, before servicing,

or when changing attachments, wheels, bits, cutters, etc.,

all tools should be disconnected.

 AVOID ACCIDENTAL STARTING. Be sure switch is off

when plugging in any tool.

 USE RECOMMENDED ACCESSORIES. Consult the

operator’s manual for recommended accessories. The

use of improper accessories may risk injury.

 NEVER STAND ON TOOL. Serious injury could occur if

the tool is tipped or if the cutting tool is unintentionally

contacted.

 CHECK DAMAGED PARTS. Before further use of the

tool, a guard or other part that is damaged should be

carefully checked to determine that it will operate properly

and perform its intended function. Check for alignment

of moving parts, binding of moving parts, breakage of

parts, mounting and any other conditions that may affect

its operation. A guard or other part that is damaged must

be properly repaired or replaced by an authorized service

center to avoid risk of personal injury.

 USE THE RIGHT DIRECTION OF FEED. Feed work into

a wheel or cutter against the direction of rotation of wheel

or cutter only.

 NEVER LEAVE TOOL RUNNING UNATTENDED. TURN

THE POWER OFF. Don’t leave tool until it comes to a

complete stop.

 PROTECT YOUR LUNGS. Wear a face or dust mask if

the cutting operation is dusty.

 PROTECT YOUR HEARING. Wear hearing protection

during extended periods of operation.

 DO NOT ABUSE CORD. Never carry tool by the cord or

yank it to disconnect from receptacle. Keep cord from

heat, oil, and sharp edges.

 ALWAYS USE AN OUTDOOR EXTENSION CORD

MARKED “W-A” OR “W”. These cords are rated for

outdoor use and reduce the risk of electric shock.

 ALWAYS KEEP THE WHEEL GUARD IN PLACE and in

working order.

 KEEP HANDS AWAY FROM CUTTING AREA. Keep

hands away from wheels. Do not reach underneathwork

or around or over the wheel while wheel is rotating. Do not

attempt to remove cut material when wheel is moving.

WHEEL COASTS AFTER BEING TURNED OFF.

4 — English

GENERAL SAFETY RULES

 NEVER USE IN AN EXPLOSIVE ATMOSPHERE. Normal

sparking of the motor could ignite fumes.

 INSPECT TOOL CORDS PERIODICALLY. If damaged,

have repaired by a qualified service technician at an

authorized service facility. The conductor with insulation

having an outer surface that is green with or without yellow

stripes is the equipment-grounding conductor. If repair

or replacement of the electric cord or plug is necessary,

do not connect the equipment-grounding conductor to a

live terminal. Repair or replace a damaged or worn cord

immediately. Stay constantly aware of cord location and

keep it well away from the rotating wheel.

 INSPECT EXTENSION CORDS PERIODICALLY and

replace if damaged.

 GROUND ALL TOOLS. If tool is equipped with three-

prong plug, it should be plugged into a three-hole

electrical receptacle.

 ONLY POWER THE TOOL WITH A GFCI (GROUND

FAULT CIRCUIT INTERRUPTOR) PROTECTED

OUTLET.

 CHECK WITH A QUALIFIED ELECTRICIAN or service

personnel if the grounding instructions are not completely

understood or if in doubt as to whether the tool is properly

grounded.

 USE ONLY CORRECT ELECTRICAL DEVICES: 3-wire

extension cords that have 3-prong grounding plugs and

3-pole receptacles that accept the tool’s plug.

 DO NOT MODIFY the plug provided. If it will not fit the

outlet, have the proper outlet installed by a qualified

electrician.

 KEEP TOOL DRY, CLEAN, AND FREE FROM OIL AND

GREASE. Always use a clean cloth when cleaning. Never

use brake fluids, gasoline, petroleum-based products, or

any solvents to clean tool.

 STAY ALERT AND EXERCISE CONTROL. Watch what

you are doing and use common sense. Do not operate

tool when you are tired. Do not rush.

 DO NOT USE TOOL IF SWITCH DOES NOT TURN IT

ON AND OFF. Have defective switches replaced by an

authorized service center.

 USE ONLY CORRECT WHEELS. Do not use wheels with

incorrect size holes. Never use washers or arbor nuts that

are defective or incorrect. The maximum wheel capacity

of your saw is 8 in. (203 mm).

 BEFORE MAKING A CUT, BE SURE ALL ADJUSTMENTS

ARE SECURE.

 NEVER TOUCH WHEEL or other moving parts during

use.

NEVER START A TOOL WHEN ANY ROTATING

COMPONENT IS IN CONTACT WITH THE WORKPIECE.

 DO NOT OPERATE A TOOL WHILE UNDER THE

INFLUENCE OF DRUGS, ALCOHOL, OR ANY

MEDICATION.

 WHEN SERVICING use only identical replacement parts.

Use of any other parts may create a hazard or cause

product damage.

 USE ONLY RECOMMENDED ACCESSORIES listed in

this manual or addendums. Use of accessories that are not

listed may cause the risk of personal injury. Instructions for

safe use of accessories are included with the accessory.

 DOUBLE CHECK ALL SETUPS. Make sure wheel is tight

and not making contact with saw or workpiece before

connecting to power supply.

 SECURE WORK firmly against the miter guide or fence.

 NEVER stand or have any part of your body in line with

the path of the wheel.

 NEVER attempt to free a stalled wheel without first turning

the saw OFF and disconnecting the saw from the power

source.

 IF THE POWER SUPPLY CORD IS DAMAGED, it must

be replaced only by the manufacturer or by an authorized

service center to avoid risk.

 AVOID AWKWARD OPERATIONS AND HAND

POSITIONS where a sudden slip could cause your hand

to move into the cutting tool.

 MAKE SURE THE WORK AREA HAS AMPLE LIGHTING

to see the work and that no obstructions will interfere with

safe operation BEFORE performing any work using the

saw.

 ALWAYS TURN OFF SAW before disconnecting it, to

avoid accidental starting when reconnecting to power

supply.

 THIS TOOL should have the following markings:

a) Wear eye, hearing, and breathing protection.

b) Use wheel guard for every operation for which it can

be used.

c) Disconnect saw before servicing, when changing

cutting wheels, and cleaning.

d) Use tool only with smooth edge cutting wheels free

of openings, grooves, and teeth.

e) Replace damaged cutting wheel before operating.

f) Do not fill water bath above water fill line.

 SAVE THESE INSTRUCTIONS. Refer to them frequently

and use to instruct other users. If you loan someone

this tool, loan them these instructions too.

SPECIFIC SAFETY RULES

5 — English

SYMBOLS

Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper

interpretation of these symbols will allow you to operate the product better and safer.

SYMBOL NAME DESIGNATION/EXPLANATION

Safety Alert Indicates a potential personal injury hazard.

Read Operator’s

Manual

To reduce the risk of injury, user must read and understand operator’s

manual before using this product.

Eye, Ear, & Breathing

Protection

Always wear eye protection with side shields marked to comply with

ANSI Z87.1 along with hearing and breathing protection.

Wet Conditions Alert Do not expose to rain or use in damp locations.

No Hands

Failure to keep your hands away from the wheel will result in

serious personal injury.

Electrocution Failure to properly ground can result in electrocution.

V Volts Voltage

A Amperes Current

Hz Hertz Frequency (cycles per second)

min Minutes Time

Alternating Current Type of current

n

o

No-Load Speed Rotational speed, at no load

.../min Per Minute Revolutions, strokes, surface speed, orbits etc., per minute

The following signal words and meanings are intended to explain the levels of risk associated with this product.

SYMBOL SIGNAL MEANING

DANGER:

Indicates a hazardous situation, which, if not avoided, will result in death or

serious injury.

WARNING:

Indicates a hazardous situation, which, if not avoided, could result in death or

serious injury.

CAUTION:

Indicates a hazardous situation, that, if not avoided, may result in minor or

moderate injury.

NOTICE:

(Without Safety Alert Symbol) Indicates information considered important, but

not related to a potential injury (e.g. messages relating to property damage).

6 — English

ELECTRICAL

ELECTRICAL CONNECTION

This tool is powered by a precision built electric motor. It

should be connected to a power supply that is 120 V, AC

only (normal household current), 60 Hz. Do not operate

this tool on direct current (DC). A substantial voltage drop

will cause a loss of power and the motor will overheat. If the

saw does not operate when plugged into an outlet, double

check the power supply.

SPEED AND WIRING

The no-load speed of this tool is approximately 5,000 rpm.

This speed is not constant and decreases under a load or

with lower voltage. For voltage, the wiring in a shop is as

important as the motor’s horsepower rating. A line intended

only for lights cannot properly carry a power tool motor. Wire

that is heavy enough for a short distance will be too light for

a greater distance. A line that can support one power tool

may not be able to support two or three tools.

GROUNDING INSTRUCTIONS

See Figure 1.

This tool must be grounded. In the event of a malfunction or

breakdown, grounding provides a path of least resistance

for electric current to reduce the risk of electric shock. This

tool is equipped with an electric cord having an equipment-

grounding conductor and a grounding plug. The plug must be

plugged into a matching outlet that is properly installed and

grounded in accordance with all local codes and ordinances.

Do not modify the plug provided. If it will not fit the outlet,

have the proper outlet installed by a qualified electrician.

WARNING:

Improper installation of the grounding plug can

result in a risk of electric shock. When repair or

replacement of the cord is required, do not connect

the grounding wire to either flat blade terminal.

The wire with insulation having an outer surface

that is green with or without yellow stripes is the

grounding wire.

Check with a qualified electrician or service personnel if the

grounding instructions are not completely understood, or if

in doubt as to whether the tool is properly grounded.

Repair or replace a damaged or worn cord immediately.

This product is for use on a nominal 120 volt circuit and has

a grounding plug similar to the plug illustrated in figure 1.

Only connect the product to an outlet having the same

configuration as the plug. Do not use an adapter with this

product.

Ground Fault Circuit Interrupter (GFCI) protection should be

provided on the circuit(s) or outlet(s) to be used for the tile

saw. Outlets are available having built-in GFCI protection

and may be used for this measure of safety.

EXTENSION CORDS

Use only 3-wire extension cords that have 3-prong grounding

plugs and 3-pole receptacles that accept the tool’s plug.

When using a power tool at a considerable distance from

the power source, use an extension cord heavy enough

to carry the current that the tool will draw. An undersized

extension cord will cause a drop in line voltage, resulting in

a loss of power and causing the motor to overheat. Use the

chart provided below to determine the minimum wire size

required in an extension cord. Only round jacketed cords

listed by Underwriter’s Laboratories (UL) should be used.

**Ampere rating (on tool data plate)

0-2.0 2.1-3.4 3.5-5.0 5.1-7.0 7.1-12.0 12.1-16.0

Cord Length Wire Size (A.W.G.)

25' 16 16 16 16 14 14

50' 16 16 16 14 14 12

100' 16 16 14 12 10 —

**Used on 12 gauge - 20 amp circuit.

NOTE: AWG = American Wire Gauge

Always use an extension cord that is designed for outside

use. This is indicated by the letters “W-A” or “W” on the

cord’s jacket.

Before using an extension cord, inspect it for loose or

exposed wires and cut or worn insulation.

Use only extension cords that are intended for outdoor

use. These extension cords are identified by a marking

“Acceptable for use with outdoor appliances; store indoors

while not in use”. Use only extension cords having an

electrical rating not less than the rating of the product. Do

not use damaged extension cords. Examine extension cord

before using and replace if damaged. Do not abuse extension

cords and do not yank on any cord to disconnect. Keep cord

away from heat and sharp edges. Always disconnect the

extension cord from the receptacle before disconnecting

the product from the extension cord.

WARNING:

Keep the extension cord clear of the working area.

Position the cord so that it will not get caught on

lumber, tools or other obstructions while you are

working with a power tool. Failure to do so can

result in serious personal injury.

WARNING:

Check extension cords before each use. If

damaged replace immediately. Never use tool with

a damaged cord since touching the damaged area

could cause electrical shock resulting in serious

injury.

7 — English

ELECTRICAL

Fig. 1

GROUNDING

GROUND FAULT

OUTLET

POWER

CORD

DRIP

LOOP

Fig. 2

EXTENSION

CORD

If the saw is used with an extension cord, ensure the

connection of the tool’s power cord and the extension cord

are not on the ground.

If a protected outlet is not available, do not use the saw

until an outlet can be changed or auxiliary protection can

be obtained. These auxiliary protection devices are available

at your local retailer.

POSITION OF THE TILE SAW

See Figure 2.

To avoid the possibility of the tool plug or outlet getting

wet, position tile saw to one side of a wall-mounted outlet

to prevent water from dripping onto the outlet or plug. The

operator should arrange a “drip loop” in the cord connecting

the saw to the outlet. The “drip loop” is that part of the cord

below the level of the outlet, or the connector if an extension

cord is used, to prevent water traveling along the cord and

coming in contact with the outlet.

If the plug or outlet does get wet, DO NOT unplug the cord.

Disconnect the fuse or circuit breaker that supplies power

to the tool then unplug and examine for the presence of

water in the outlet.

WARNING:

To reduce the risk of electrocution, keep all

connections dry and off the ground. Do not touch

the plug with wet hands.

8 — English

FEATURES

RUBBER

BOOT

WATER TRAY

EXTENSION

BEVEL LOCK

KNOB

ON/OFF

SWITCH

DEPTH STOP

LOCK KNOB

CUTTING WHEEL

GUARD

SLIDING TABLE

LOCK LEVER

DRAINAGE

DRAIN

CAP

SLIDING TABLE

FENCE

Fig. 3

PRODUCT SPECIFICATIONS

Wheel Diameter ............................................................8 in.

Wheel Arbor .............................................................. 5/8 in.

Rip Capacity (Tile size) ...............................................24 in.

Diagonal Capacity (Tile size) ......................................18 in.

Maximum Depth of Cut .........................................2-3/4 in.

Rating ...........................................120 V~, 12 Amps, 60 Hz

No Load Speed .....................................5,000 r/min. (RPM)

CUTTING

WHEEL

MITER

GUIDE

MAX WATER

FILL LINE

WATER

TRAY

SLIDING

TABLE

FRAME

PULL

HANDLE

WHEELS

MIN WATER

FILL LINE

LASER

SWITCH

WHEEL

HOOD

WATER

FILTER

GREASE

PENCIL

STORAGE

MOTOR HEAD

LOCK KNOB

WRENCH

STORAGE

9 — English

FEATURES

KNOW YOUR TILE SAW

See Figure 3.

The safe use of this product requires an understanding of

the information on the tool and in this operator’s manual as

well as a knowledge of the project you are attempting. Before

use of this product, familiarize yourself with all operating

features and safety rules.

8 in. TILE CUTTING WHEEL - An 8 in. tile cutting wheel is

included with your saw.

WARNING:

Do not use wheels rated less than the speed of

this tool. Failure to heed this warning could result

in personal injury.

BEVEL LOCK KNOB - The bevel lock knob securely locks

the saw head at any bevel angle between 0º and 45º. It is

recommended that you only make bevel cuts at 0˚, 22.5˚,

and 45˚ angles.

WARNING:

Making bevel cuts at angles other than 0˚, 22.5˚,

and 45˚ angles could cause the cutting wheel to

come in contact with the sliding table resulting in

damage to the unit and/or possible serious injury.

ADJUSTABLE LASER ALIGNMENT SYSTEM - For more

accurate cuts, a laser guide is included with the tile saw.

When used properly, the laser guide makes accurate,

precision cutting simple and easy. Simply push the button

to turn the laser on or off.

MITER GUIDE - The easy-to-read indicator on the miter

guide shows the exact angle for a miter cut with detents at

0°, 22.5°, and 45°.

ON/OFF SWITCH - This saw has an easy access power

switch located on the saw arm. To lock the switch, install

a padlock (not included) through the hole in the switch

trigger. When the lock is installed and locked, the switch is

inoperable. Store the padlock key in another location.

SLIDING TABLE - The sliding table allows the user to slide

the workpiece into the cutting wheel for accurate cuts.

SPLASH GUARD ASSEMBLY WITH TOOLESS

REMOVABLE SIDE GUARD - The splash guard helps

contain spray and mist.

SUBMERSIBLE PUMP - The submersible pump (not shown)

provides water to the cutting wheel.

WATER TRAY EXTENSION - When cutting larger tile, the

extension keeps work area cleaner and drier.

WRENCH STORAGE - The tile saw has a convenient storage

area specifically designed for wrenches.

TOOLS NEEDED

The following tools (not included or drawn to scale) are needed for assembly and alignment:

Fig. 4

10 mm WRENCH

FRAMING SQUARE

COMBINATION SQUARE

10 — English

The following items are included with your tile saw:

MAX

MIN

LOOSE PARTS

A

R

B

T

D

M

H

G

L

I

P

K

J

Fig. 5

A - Motor head assembly ...............................................1

B - Hex key (6 mm) ......................................................... 1

C - Wheel wrench ...........................................................1

D - Arbor nut ...................................................................1

E - Cutting wheel ...........................................................1

F - Inner washer .............................................................1

G - Outer washer ............................................................1

H- Miter guide ...............................................................1

I - Sliding table .............................................................. 1

J - Frame .......................................................................1

K - Water tray .................................................................1

L - Water filter ................................................................1

M - Cap screw ................................................................4

N - Water pump ..............................................................1

O - Screw ........................................................................1

P - Washer ......................................................................1

Q - Rear splash guard ....................................................1

R - Side splash guard ..................................................... 1

S - Water tray extension ................................................. 1

T - Hex key (2.5 mm) ...................................................... 1

O

E

C

N

F

Q

S

11 — English

ASSEMBLY

Fig. 6

MOTOR HEAD

ASSEMBLY

WRENCH

STORAGE

HOLES

FRAME

SOCKET HEAD

SCREWS

POSTS

UNPACKING

See Figure 5.

This product requires assembly.

 Carefully lift the parts from the carton and place on a level

work surface.

NOTE: Many of the Loose Parts are stored in the water

reservoir.

WARNING:

Do not use this product if any parts on the Loose

Parts list are already assembled to your product

when you unpack it. Parts on this list are not

assembled to the product by the manufacturer and

require customer installation. Use of a product that

may have been improperly assembled could result

in serious personal injury.

 Inspect the tool carefully to make sure no breakage or

damage occurred during shipping.

 Do not discard the packing material until you have carefully

inspected and satisfactorily operated the tool.

 The saw is factory set for accurate cutting. After assembling

it, check for accuracy. If shipping has influenced the

settings, refer to specific procedures explained in this

manual.

 If any parts are damaged or missing, please call

1-866-539-1710 for assistance.

WARNING:

If any parts are damaged or missing do not operate

this tool until the parts are replaced. Use of this

product with damaged or missing parts could

result in serious personal injury.

WARNING:

Do not attempt to modify this tool or create

accessories not recommended for use with this

tool. Any such alteration or modification is misuse

and could result in a hazardous condition leading

to possible serious personal injury.

WARNING:

Do not connect to power supply until assembly

is complete. Failure to comply could result in

accidental starting and possible serious personal

injury.

INSTALLING MOTOR HEAD ASSEMBLY TO

FRAME

See Figure 6.

Align the holes in the motor head assembly with the holes

on the frame.

Lower the motor head assembly onto the posts.

Thread socket head screws through motor head assembly

and into holes on frame.

Tighten screws using the 6 mm hex key (provided).

 NOTE: Wrench storage is located in the back of the motor

head assembly.

Set motor head and frame assembly aside.

12 — English

MAX

MIN

ASSEMBLY

Fig. 7

WATER

FILTER

WATER TRAY

FILTER SLOTS

INSTALLING WATER FILTER AND WATER

PUMP

See Figures 7 - 9.

The water pump recirculates water from the tray to the

cutting wheel.

Locate filter slots and pump well in water tray. Pump well

is marked, “pump well.”

Slide filter into filter slots, as shown.

Locate the “Max/Min” water flow selector on the pump.

For best performance, start with the flow to “Max” to

control the flow of water over the wheel.

NOTE: Water flow can be adjusted during use by

removing the filter, reaching into water well and turning

flow selector on pump. Reinsert filter.

Place water pump into pump well.

WHEEL

PUMP WELL

POWER

CORD

NOTCH

Fig. 8

WATER

FLOW

SELECTOR

MAXIMUM

FLOW

WATER PUMP

POWER CORD

WATER

HOSE

NOTCH

PUMP

WELL

13 — English

WATER

TRAY

MOTOR HEAD

AND FRAME

ASSEMBLY

Fig. 9

INSTALLING WATER TRAY

See Figure 8 - 9.

 Place the water tray, with the pump and filter in place,

on a sturdy flat surface or on level ground.

Attach the water hose to the pump elbow.

Carefully lift the motor head and water tray frame

assembly over the water tray, as shown.

 Tilt the water tray frame and insert heavy duty tab into

the bar slot on water tray.

Secure the water tray frame in place with latches on front

of the water tray.

LATCHES

HEAVY DUTY

TAB

BAR SLOT

RUBBER

BOOT

PUMP

POWER

CORD

Connect the pump power cord to the motor head power

cord. Check that the rubber boot is pulled over cord

connection to help keep water off the plug.

NOTE: The pump turns on when the motor is turned on.

Let the cutting wheel build up to full speed and wait for

the wheel to get wet before moving the material into the

wheel.

Rest power cord and water hose in the notches provided

on the water tray.

PUMP ELBOW

WATER HOSE

ASSEMBLY

14 — English

INSTALLING THE SLIDING TABLE

See Figure 10.

To install the sliding table:

Grasp the table firmly and set the rollers on the front of

rails.

Holding the table parallel with the frame, push the table

toward the back of the saw.

When the table lock lever reaches the stop on the front

rail on the right hand side of the frame, pull the lever out

and hold it out until the lock has passed the stop. Release

the lever.

Slide the table along the rails until the final rollers engage

the rails.

To lock sliding table:

Pull the table lock lever out and turn 90˚ counterclockwise.

Release the lever.

NOTE: When the sliding table is installed, and you push

the table, it will “click” into place. This is the table lock

lever snapping into a hole in the frame locking the table

in place.

To unlock the sliding table:

Pull the table lock lever out and turn 90˚ clockwise.

TILE CUTTING WHEEL

For maximum performance and safety, it is recommended

that you use the 8 in. cutting wheel provided with your

saw. Additional cutting wheels of the same high quality are

available at your local dealer.

WARNING:

Do not use cutting wheels rated less than the no

load speed of this tool. Failure to heed this warning

could result in personal injury. Do not use wheel

with cracks, gaps, or teeth.

INSTALLING THE CUTTING WHEEL

See Figure 11.

WARNING:

A 8 in. tile cutting wheel is the maximum wheel

capacity of the saw. Never use a wheel that is

too thick to allow wheel washer to engage with

the flats on the arbor. Larger wheels will come

in contact with the splash hood, while thicker

wheels will prevent the wheel bolt from securing

the wheel on the arbor. Either of these situations

could result in a serious accident and can cause

serious personal injury.

 Unplug the saw.

 Lock table in front position.

 Loosen wheel guard knob by turning counterclockwise

and open the cutting wheel guard.

ASSEMBLY

ARBOR

NUT

OUTER

WASHER

CUTTING

WHEEL

6 mm HEX

WRENCH

Fig. 11

WATER

NOZZLES

Fig. 10

SAW

FRONT

ROLLERS

SLIDING

TABLE

TABLE LOCK

LEVER

WHEEL

WRENCH

WHEEL GUARD

KNOB

INNER

WASHER

OUTER

WATER

NOZZLE

LOCK

UNLOCK

BYPASS

CUTTING WHEEL

GUARD

15 — English

Fig. 12

 Place the wheel wrench on the arbor nut then slide the

6 mm hex wrench into the arbor.

 Holding the hex wrench firmly to prevent movement, turn

the wheel wrench counterclockwise to loosen.

 Remove the arbor nut and outer washer, leaving the inner

washer on the arbor.

WARNING:

If inner washer has been removed, replace it before

placing wheel on arbor. Failure to do so could

cause an accident since the wheel will not tighten

properly. Never use wheels that have openings,

grooves, or teeth on this tool.

 Place the cutting wheel onto arbor with the arrows on

wheel going in the counterclockwise direction.

NOTE: Two water nozzles come installed on this product. Be

sure to install cutting wheel so that there is a water nozzle on

each side of cutting wheel with water ports facing the cutting

wheel. The outer water nozzle can be easily removed for

installation of cutting wheel. Check that outer nozzle outlet

hole has been reattached with water port facing toward the

cutting wheel.

 Replace the outer washer. The double “D” flats on the

washers align with the flats on the arbor.

 Replace the arbor nut on the arbor. Using wheel wrench

and arbor wrench, tighten arbor nut securely.

INSTALLING SPLASH GUARD ASSEMBLY

See Figures 12 - 14.

The splash guard on this saw is a two-part assembly.

Attaching rear splash guard:

Line up rear splash guard holes with screw hole and post

on back of cutting wheel guard, as shown.

ASSEMBLY

HOLE

SIDE SPLASH

GUARD

SCREW HOLE

POST

REAR SPLASH

GUARD

WASHER

POST

SIDE SPLASH

GUARD

Fig. 14

REAR SPLASH

GUARD

Fig. 13

RIDGE

GROOVE

REAR

SPLASH

GUARD

Insert screw through washer and splash guard then thread

into screw hole.

Tighten securely. Be careful not to overtighten.

Attaching side splash guard:

Install side splash guard over the rear splash guard.

Insert post, located on side of cutting wheel guard,

through hole in side flap of guard.

Settle splash guard grooves over ridges in cutting wheel

guard.

Repeat with other side.

After assembly is complete, pull rear splash guard

outward so flaps rest over side splash guard.

SCREW

16 — English

ASSEMBLY

INSTALLING WATER TRAY EXTENSI

ON

See Figure 15.

 Standing at the back of the saw, hold the water tray

extension with the tray tabs toward the slots.

 Tilt the tray and slip the tray tabs between the frame top

and frame bottom. Tray should be over pump power

cord and water hose.

Once the extension slides into place, lower until the tray

tabs fit into the holes under frame.

INSTALLING THE MITER GUIDE

See Figure 16.

The miter guide can be used from both the left and right side

of the cutting wheel.

Place the slot on the underside of the miter guide on the

sliding table fence.

Lock the miter guide securely to the table by turning the

miter guide knob clockwise.

To adjust angles:

Loosen the miter guide knob.

Set to the desired angle by moving the guide left or right.

Tighten the knob securely.

FILLING/CHANGING THE WATER RESERVOIR

See Figure 17.

Install drain cap.

Fill the water reservoir with clean tap water to the fill line.

Do not fill past the “maximum” line on the tray.

To change reservoir water:

Unplug the saw.

Remove the drain cap and empty waste water into a

bucket. Do not allow the water to splash onto the ground

or around the machine.

Rinse the water reservoir thoroughly.

Discard the waste water in accordance with local

regulations.

Replace the drain cap and refill tray with clean water.

NOTE: Drain fits standard size garden hose.

Fig. 15

Fig. 16

WATER

TRAY

WATER TRAY

EXTENSION

TO TIGHTEN

MITER GUIDE

KNOB

MITER

GUIDE

TRAY TAB

TO LOOSEN

FRAME

DRAIN CAP

Fig. 17

MAXIMUM

FILL LINE

MINIMUM

FILL LINE

WATER

RESERVOIR

SLIDING

TABLE

FENCE

17 — English

ASSEMBLY

Fig. 18

TRANSPORTING THE TILE SAW

See Figure 18.

Lock the sliding table.

Remove the water tray extension.

Be sure the hoses and cords do not drag on the ground.

Saw is easily moved, using pull handle and wheels.

OPERATION

WARNING:

Do not allow familiarity with tools to make you

careless. Remember that a careless fraction of a

second is sufficient to inflict serious injury.

WARNING:

Always wear eye protection with side shields

marked to comply with ANSI Z87.1 along with

hearing and breathing protection. Failure to do so

could result in objects being thrown into your eyes,

resulting in possible serious injury.

WARNING:

Do not use any attachments or accessories

not recommended by the manufacturer of this

tool. The use of attachments or accessories not

recommended can result in serious personal injury.

APPLICATIONS

This saw is designed to cut man-made tile, pavers, stone

tile, and pavers up to 4 in maximum.

You may use this tool for the purposes listed below:

Straight line cutting operations such as cross cutting,

mitering, ripping, plunging, and beveling

Cutting garden stone

18 — English

OPERATION

Fig. 19

SWITCH

ON

SWITCH

OFF

PADLOCK

ON/ OFF

SWITCH

Fig. 20

D-HANDLE

MOTOR HEAD

LOCK KNOB

MOTOR HEAD

ON/OFF SWITCH

See Figure 19.

To turn your saw on:

 Lift the switch to turn on.

To turn your saw off:

 Press the switch down to turn off.

To lock your saw:

 With the saw turned off, install a padlock (not included)

through the hole in the switch.

WARNING:

In the event of a power failure or when the tool is

not in use, turn the on/off switch off. This action

will prevent the tool from accidentally starting when

power returns.

WARNING:

ALWAYS make sure your workpiece is not in

contact with the cutting wheel before operating the

switch to start the tool. Failure to heed this warning

can cause the workpiece to be kicked back toward

the operator and result in serious personal injury.

WARNING:

To reduce the risk of accidental starting, ALWAYS

make sure the on/off switch is in the off position

before plugging tool into the power source.

LOCKING/UNLOCKING THE MOTOR HEAD

FOR PLUNGE CUTS

See Figure 20.

To unlock and raise the motor head:

 Firmly grasp the “D” handle and apply downward pressure

while at the same time turning the motor head lock knob

counterclockwise.

 Slowly raise the motor head.

To lock the motor head:

 Firmly grasp the “D” handle and apply downward pressure

while at the same time turning the motor head lock knob

clockwise to lock.

NOTE: For all through cuts, place the saw in the locked

position.

19 — English

OPERATION

MAKING CUTS

Always draw the line to be cut on the tile using a marker or

grease pencil. If the tile is shiny and hard-to-mark, place

masking tape on the tile and mark the tape.

A common problem when cutting tile is straying from the

marked line. Once you’ve strayed from the mark, you can not

force the wheel back to the line by twisting the tile. Instead,

back up and recut the tile slicing off a small amount of tile

until the wheel is back on track.

To avoid this problem, use the miter guide whenever

possible.

Another problem is cutting difficult material. To prevent

chipping of the material at the end of the cut, use a plunge

cut.

NOTE: A more shallow blade adjustment may help minimize

chipping, see the Depth stop adjustments section.

Clean the saw table and miter guide frequently during use.

Debris from the cut material can interfere with tool function.

DANGER:

Laser radiation. Avoid direct eye contact with light

source.

WARNING:

Use of controls or adjustments or performance of

procedures other than those specified herein may

result in hazardous radiation exposure.

USING THE LASER GUIDE

See Figure 21.

Using a straight edge or square, draw a mark on the tile

with a marker or grease pencil. Turn the laser on and off by

pressing the laser guide switch located on the side of the

“D” handle. When the laser is turned on it will generate a red

line on the work surface. This line will let you see your mark

and the laser guide line at the same time, and will assist you

in lining up the mark for more accurate cutting of the tile.

NOTE: Laser may be difficult to see in bright sunlight.

With the wheel in the cutting position, move the tile until the

mark and the laser line are aligned.

Make several practice cuts on different styles and thickness

of material. Repeat the steps as necessary.

Removing Your Mark:

Position the tile so that the laser line is near the left edge of

your mark in order to remove the mark.

To Cut Your Mark:

Position the tile so that the laser line is near or over your

mark in order to cut the mark.

To Leave Your Mark:

Position the tile so that the laser line is near the right edge

of your mark in order to leave the mark.

After you have become familiar with using the laser guide,

you will be able to remove, cut, or leave your mark on the

work surface. Practice will teach you the correct position for

aligning your mark with the laser line.

To adjust the position of the laser guide line, refer to the

Adjustments section later in this manual.

Fig. 21

MARK

LASER SWITCH

20 — English

OPERATION

TO MAKE A CROSS CUT / RIP CUT

See Figure 22.

Cross/rip cuts are straight 90° cuts. The material is fed into

the cut at a 90° angle to the wheel, and the wheel is vertical.

Using a straight edge or square, draw a line on the tile

with a marker or grease pencil.

 Set the miter guide to 0° for right side or 90° for left side

use. Tighten the lock knob, and lock in place.

Make sure miter guide is not in the cut path.

 Place the material on the table and firmly against the miter

guide and fence.

 Make sure the material is clear of the cutting wheel before

turning on the saw.

 Flip the on/off switch to the on position.

 Let the cutting wheel build up to full speed and wait for

the wheel to get wet before moving the material into the

wheel.

 Hold the material firmly against the miter guide and fence

and slowly feed the material into the cutting wheel.

 When the cut is made, turn the saw off. Wait for the cutting

wheel to come to a complete stop before removing any

part of the material.

TO MAKE A DIAGONAL CUT

See Figure 23.

Diagonal cuts are also referred to as “long point-to-long

point cuts”.

Using a straight edge or square, draw a line on the tile

with a marker or grease pencil.

 Set the miter guide to 0° for right side or 90° for left side

use. Tighten the lock knob, and lock in place.

Make sure miter guide is not in the cut path.

 Place the material on the table and firmly against the miter

guide and fence.

 Make sure the material is clear of the cutting wheel before

turning on the saw.

 Flip the on/off switch to the on position.

 Let the cutting wheel build up to full speed and wait for

the wheel to get wet before moving the material into the

wheel.

DIAGONAL CUT

Fig. 23

SLIDING

TABLE

FENCE

CROSS CUT / RIP CUT

MARK

MITER

GUIDE

Fig. 22

LOCK

KNOB

 Hold the material firmly against the miter guide and fence

and slowly feed the material into the cutting wheel.

 When the cut is made, turn the saw off. Wait for the cutting

wheel to come to a complete stop before removing any

part of the material.

La page charge ...

RIDGID R4040S-FT3500-FT3508-FT7007-FT7001 Manuel utilisateur

Ce manuel convient également à

RIDGID R4040S-FT3500-FT3508-FT7007-FT7001 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents