ACE 21AK125G900 Le manuel du propriétaire

Marque: ACE

Modèle: 21AK125G900

Catégorie: Mini motoculteurs

Taper: Le manuel du propriétaire

Ce manuel convient également à

7306699

Operator

s Manual

2-Cycle Gas Cultivator

Y125

TABLE OF CONTENTS

Service information ..................................... 1

Rules for Safe Operation ................................. 2

Know Your Unit ........................................ 5

Specifications ......................................... 5

Assembly instructions ................................... 6

Oil and Fuel Information ................................. 7

Starting and Stopping instructions ......................... 8

Operating instructions ................................... 9

Maintenance and Repair ................................ 10

Cleaning and Storage .................................. 13

Troubleshooting Chart .................................. 14

Warranty information ................................... 16

SAVE THESE INSTRUCTIONS

DO NOT RETURN THIS UNIT TO THE RETAILER. PROOF OF

PURCHASE WILL BE REQUIRED FOR WARRANTY SERVICE.

For assistance regarding the assembly, controls, operation or

maintenance of the unit, please call the Customer Support Department

at 1-800-800-7310 in the United States or 1-800-668-1238 in Canada.

Additional information about the unit can be found on our website at

www.mtdproducts.com or www.mtdproducts.ca.

For service, please call the Customer Support Department to obtain

a list of authorized service dealers near you. Service on this unit,

both within and after the warranty period, should only be performed

by an authorized and approved service dealer. When servicing, use

only identical replacement parts.

All information, illustrations, and specifications in this manual are based

on the latest product information available at the time of printing. We

reserve the right to make changes at any time without notice.

769=06986 PO0 08/11

The purpose of safety symbols is to attract your attention to

possible dangers. The safety symbols, and their explanations,

deserve your careful attention and understanding. The safety

warnings do not by themselves eliminate any danger. The

instructions or warnings they give are not substitutes for proper

accident prevention measures.

i SYMBOL MEANING ]

_ ANGER: Signals an EXTREME hazard.

Failure to obey a safety DANGER signal WILL result in

serious injury or death to yourself or to others.

_ ARNING: Signals a SERIOUS hazard.

Failure to obey a safety WARNING signal CAN result in

serious injury to yourself or to others.

IA! s.0oa,sa oo haza d

Failure to obey a safety CAUTION signal MAY result in

property damage or injury to yourself or to others.

NOTE: Advises you of information or instructions vital to the operation

or maintenance of the equipment.

SPARK ARRESTOR NOTE

NOTE: For users on U.S. Forest Land and in the states of

California, Maine, Oregon and Washington. All U.S. Forest Land

and the state of California (Public Resources Codes 4442 and

4443), Oregon and Washington require, by law that certain internal

combustion engines operated on forest brush and/or grass-covered

areas be equipped with a spark arrestor, maintained in effective

working order, or the engine be constructed, equipped and

maintained for the prevention of fire. Check with your state or local

authorities for regulations pertaining to these requirements. Failure

to follow these requirements could subject you to liability or a fine.

This unit is factory equipped with a spark arrestor, if it requires

replacement, ask your LOCAL SERVICE DEALER to install the

Accessory Part #753=06792 Muffler Assembly.

CALiFORNiA PROPOSITION 65

WARNING: Engine exhaust, some of its constituents and

certain finished components contain or emit chemicals known

to the State of California to cause cancer and birth defects or

other reproductive harm. Wash hands after handling.

Read the Operator's Manual and follow all warnings and safety

instructions. Failure to do so can result in serious injury to the

operator and/or bystanders.

FOR QUESTIONS, CALL 1=800=800=7310 iN U.S.

OR 1=800=668=1238 iN CANADA.

* iMPORTANT SAFETY iNSTRUCTiONS *

READ ALL iNSTRUCTiONS BEFORE OPERATING

WARNIN6: When using the unit, you must follow the

safety rules. Please read these instructions before operating

the unit in order to ensure the safety of the operator and any

bystanders. Please keep these instructions for later use.

Read the instructions carefully. Be familiar with the controls and

proper use of the unit.

Do not operate this unit when tired, ill, or under the influence of

alcohol, drugs, or medication.

Children and teens under the age of 15 must not use the unit,

except for teens guided by an adult.

All guards and safety attachments must be installed properly

before operating the unit.

Inspect the unit before use. Replace damaged parts. Check for

fuel leaks. Make sure all fasteners are in place and secure.

Replace parts that are cracked, chipped, or damaged in any

way. Do not operate the unit with loose or damaged parts.

Carefully inspect the area before starting the unit. Remove all

debris and hard or sharp objects such as glass, wire, etc.

Be aware of the risk of injury to the head, hands and feet.

Clear the area of children, bystanders, and pets. At a minimum,

keep all children, bystanders, and pets outside a 50 feet (15 m)

radius; there still may be a risk to bystanders from thrown

objects. Bystanders should be encouraged to wear eye

protection. If you are approached, stop the unit immediately.

Squeeze the throttle control and check that it returns

automatically to the idle position. Make all adjustments or

repairs before using unit.

SAFETY WARNINGS FOR GAS UNITS

I _ I _IARNJNG: Gasoline is highly flammable, and its vapors J

can explode if ignited. Take the following precautions:

• Store fuel only in containers specifically designed and approved

for the storage of such materials.

Always stop the engine and allow it to cool before filling the fuel

tank. Never remove the fuel tank cap or add fuel when the

engine is hot. Always loosen the fuel tank cap slowly to relieve

any pressure in the tank before fueling. Do not smoke.

Always mix and add fuel in a clean, well-ventilated outdoor area

where there are no sparks or flames. Do not smoke.

Never operate the unit without the fuel cap securely in place.

Avoid creating a source of ignition for spilled fuel. Wipe up any

spilled fuel from the unit immediately before starting the unit.

Move the unit at least 30 feet (9.1 m) from the fueling source and

site before starting the engine. Do not smoke.

Never start or run the unit inside a closed room or building.

Breathing exhaust fumes can kill. Operate this unit only in a well-

ventilated outdoor area.

WHILE OPERATING

Wear safety glasses or goggles that are marked as meeting

ANSI Z87.1-1989 standards. Also wear ear/hearing protection

when operating this unit. Wear a face or dust mask if the

operation is dusty. Long sleeve shirts are recommended.

Wear heavy, long pants, boots and gloves. Do not wear loose

clothing, jewelry, short pants, sandals or go barefoot. Secure

hair above shoulder level.

This unit has a clutch. The tines remains stationary when the

engine is idling. If it does not, have the unit adjusted by an

authorized service technician.

Be sure the tines are not in contact with anything before starting

the unit.

Use the unit only in daylight or good artificial light.

Avoid accidental starting. The operator and unit must be in a stable

position while starting. See Starting and Stopping Instructions.

Use the right tool. Only use this tool for the purpose intended.

Use extreme caution when reversing or pulling the unit towards you.

Do not overreach. Always keep proper footing and balance. Take

extra care when working on steep slopes or inclines.

Always hold the unit with both hands when operating. Keep a

firm grip on the grips.

Keep hands, face, and feet at a distance from all moving parts.

Do not touch or try to stop the tines when they are rotating.

Do not touch the engine or muffler. These parts get extremely

hot from operation. They remain hot for a short time after you

turn off the unit.

Do not operate the engine faster than the speed needed to cultivate.

Do not run the engine at high speed when you are not cultivating.

Always stop the engine when cultivating is delayed or when

walking from one location to another.

If you strike or become entangled with a foreign object, stop the

engine immediately and check for damage. Do not operate

before repairing damage. Do not operate the unit with loose or

damaged parts.

Stop and switch the engine to off for maintenance, repair, or to

install or remove the tines.

Use only original equipment manufacturer replacement parts

and accessories for this unit. These are available from your

authorized service dealer. Use of any unauthorized parts or

accessories could lead to serious injury to the user, or damage

to the unit, and void your warranty.

Keep unit clean of vegetation and other materials. They may

become lodged between the tines.

To reduce fire hazard, replace faulty muffler and spark arrestor,

keep the engine and muffler free from grass, leaves, excessive

grease or carbon build up.

OTHER SAFETY WARNINGS

Never store the unit, with fuel in the tank, inside a building where

fumes may reach an open flame or spark.

Allow the engine to cool before storing or transporting. Be sure

to secure the unit while transporting.

Store the unit in a dry area, locked up or up high to prevent

unauthorized use or damage, out of the reach of children.

Never douse or squirt the unit with water or any other liquid.

Keep handles dry, clean and free from debris. Clean after each

use. See the Cleaning and Storage instructions.

Keep these instructions. Refer to them often and use them to

instruct other users. Ifyou loan someone this unit, also loan

them these instructions.

SAVE THESE iNSTRUCTiONS

,, SAFETY AND iNTERNATiONAL SYMBOLS ,,

This operator's manual describes safety and international symbols and pictographs that may appear on this product. Read the operator's

manual for complete safety, assembly, operating, maintenance, and repair information.

SYMBOL MEANING

L ,=SAFETY ALERT SYMBOL

_ Indicates danger, warning or caution. May be used in

_ib conjunction with other symbols or pictographs.

." WARNING- READ OPERATOR'S MANUAL

_]l I I_ Read the operator s manual(s) and follow all warnings

and safety instructions. Failure to do so can result in

serious injury to the operator and/or bystanders.

= " WEAR EYE AND HEARING PROTECTION

! WARNING: Thrown objects and loud noise can

_ |' cause severe eye injury and hearing loss. Wear eye

p protection meeting ANSI Z87.1-1989 standards and

ear protection when operating this unit. Use a full face

shield when needed.

_"_'_qJ'II'' _ o UNLEADED FUEL

!_q'_ _" Always use clean, fresh unleaded fuel

* OIL

Refer to operator s manual for the proper type of oil.

'%. * DO NOT USE E85 FUEL IN THIS UNIT

WARNING: It has been proven that fuel

containing

{ _._ J greater than 10% ethanol will likely damage this

_. engine and void the warranty.

m * ON/OFF STOP CONTROL

ON / START / RUN

• ON/OFF STOP CONTROL

U OFF or STOP

. PRIMER BULB

Push prmerbub fulyandslowy 10times.

121I'_1 I1'1" CHOKE CONTROL

1. • FULL choke position

I 2. * PARTIAL choke position

3. * RUN choke position

SYMBOL MEANING

.... ,KEEP BYSTANDERS AWAY

L-,,,_-r_,_WARNING: Keep all bystanders, especially childre n

_. and pets. at !east 50 feet (15m)fro m the operating areai '

mTHROWN OBJECTS AND ROTATING CUTTER CAN

_7_ CAUSE SEVERE INJURY

_>_! WARNING: Small object s can be prope!led at high

_/_t_'4 _. speed causing injury. Keep away from the rotating rotor.

HOT SURFACE WARNING

DOnottouchahotmu,ler0rcY"ndei:Youmayget

burned. These parts get extremely hot from operation,

When turned off they remain hot for a Short timel

, GARDEN CU LTIVATORS _ ROTATING TIN ES CAN

CAUSE SEVERE INJURY

WARNING:st0P the enginezmet0r and allow

tines to stop before installing or removing tines, or

before Cleaning Or performing any maintenancel KeeP

hands and feet away from rotating tines.

:, NO STEP

AlwaYS keep proper f0oting and balanCe: DO not

J overreach, take extra care when working on steep

slopes or inclines:

, PLACE RIGHT FOOT HER E

[ __.I _ Avoid accidental starting. Stand in the starting position

_ Whenever pulling the starter rope: The operato r and Unit

_'_" . must bein a stable position while starting.

APPLiCATiON

• Cultivatingsodandlight to medium soil

= Cultivating in garden areas, around trees, etc. Throttle Control

NO ASSEMBLY TOOLS REQUIRED

Air Filter Cover

Muffler

Spark Plug

Starter Rope

Grip

Choke Lever

Handlebar

Knobs

Upper Handle

On/Off Control

Fuel Cap

Primer Bulb Tine Guard Lower Handle

Gear Box Assembly

Tines

Engine Type ....................................................................................... Air-Cooled, 2-Cycle

Displacement ................................................................................................. 25 cc

Idle Speed RPM ...................................................................................... 2,600-3,600 rpm

Operating RPM ........................................................................................... 7,800+ rpm

Clutch Type .............................................................................................. Centrifugal

Spark Plug Gap .................................................................................. 0.025 inch (0.635 mm)

Lubrication ........................................................................................... Fuel/Oil Mixture

Fuel/Oil Ratio .................................................................................................. 40:1

Fuel Tank Capacity .................................................................................. 10 ounces (295 ml)

Cultivating Path Width (Maximum) ...................................................................... 9 inches (22.86 cm)

Cultivating Depth (Maximum) .......................................................................... 6 inches (15.24 cm)

Approximate Weight (no fuel) ..................................................................... 23 - 24 Ib (10.4 - 10.9 kg)

* All specifications are based on the latest product information available at the time of printing. We reserve the right to make changes at any

time without notice.

ASSEMBLINGTHE UNiT

Begin by carefully unpacking the contents and making sure that

nothing is damaged.

iNSTALLiNG AND ADJUSTING THE WHEEL ASSEMBLY

_ ARNING: To prevent serious personal injury, the wheel I

assembly must be installed when operating the unit.

_ WARN'N6: To avoid injury from the tines, wear heavy l

gloves and a long sleeve shirt when installing the wheel

assembly.

Installing the Wheel Assembly

1. Set the unit on its side (Fig. 1).

2. Insert the wheel assembly into the wheel bracket until the height

adjustment button locks into place (Fig. 1).

NOTE: it may be necessary to adjust the position of the wheel

assembly before using the unit.

Adjusting the Wheel Assembly

1. Set the unit on its side (Fig. 1).

2. Press the height adjustment button inward and move the wheel

assembly until the height adjustment button locks into the

desired hole (Fig. 1).

NOTE: Moving the wheel assembly down will raise the wheel height.

Moving the wheel assembly up will lower the wheel height.

Adjust%ent As_eebl,,

Button

Wheel

Lower _ Raise "_-____ Bracket

Fig. 1

Fig. 2

HandJebar

Knobs

Throttle Cable

and Switch Wires

HandJebar Knobs

POSITIONING THE HANDLEBARS

1. Loosen the two knobs on the inside of the handlebars (Fig. 3).

2. With the unit upright, swing the handlebars up into the operating

position (Fig. 2).

NOTE: Take care not to pinch the throttle cable or switch wires

when positioning the handlebar (Fig. 3).

3. Tighten the knobs to secure the handlebars in place (Fig. 3).

NOTE: Do not over tighten the knobs.

4. Readjust the throttle cable and switch wires so they are smooth

and tight against the handlebar assembly. This will help prevent

them from catching or snagging during normal operation.

Fig. 3

OiL AND FUEL MiXiNG iNSTRUCTiONS

Old and/or improperly mixed fuel are the main reasons for the unit

not running properly. Be sure to use fresh, clean unleaded fuel.

Follow the instructions carefully for the proper fuel/oil mixture.

Definition of Blended Fuels

Today's fuels are often a blend of gasoline and oxygenates such as

ethanol, methanol, or MTBE (ether). Alcohol-blended fuel absorbs

water. As little as 1% water in the fuel can make fuel and oil

separate, it forms acids when stored. When using alcohol-blended

fuel, use fresh fuel (less than 30 days old).

Using Blended Fuels

If you choose to use a blended fuel, or its use is unavoidable, follow

recommended precautions:

• Always use the fresh fuel mix explained in your operator's manual

Use the fuel additive STA-BIL® or an equivalent

Always agitate the fuel mix before fueling the unit

Drain the tank and run the engine dry before storing the unit

Using Fuel Additives

The bottle of 2-cycle oil that came with your unit contains a fuel

additive which will help inhibit corrosion and minimize the formation

of gum deposits, it is recommended that you use our 2-cycle oil

with this unit.

if unavailable, use a good 2-cycle oil designed for air-cooled

engines along with a fuel additive, such as STA-BIL Gas Stabilizer or

an equivalent. Add 0.8 oz. (23 ml) of fuel additive per gallon of fuel

according to the instructions on the container. NEVER add fuel

additives directly to the unit's fuel tank.

it has been proven that fuel containing greater than 10%

ethanol will likely damage this engine and void the warranty.

Mixing the Fuel

FUELING THE UNiT

WARNING: Gasoline is extremely flammable, ignited

vapors may explode. Always stop the engine and allow it

to cool before filling the fuel tank. Do not smoke while

filling the tank. Keep sparks and open flames at a distance

from the area.

_ ARNING: Remove fuel cap slowly to avoid injury from

fuel spray. Never operate the unit without the fuel cap

securely in place.

_ ARNING: Add fuel in a clean, well ventilated outdoor

area. Wipe up any spilled fuel immediately. Avoid creating

a source of ignition for spilt fuel. Do not start the engine

until fuel vapors dissipate.

1. Position the unit with the fuel cap facing up.

2. Remove the fuel cap.

3. Place the fuel container spout into the fill hole on the fuel tank

and fill the tank.

NOTE: Do not overfill the tank.

4. Wipe up any fuel that may have spilled.

5. Reinstall the fuel cap.

6. Move the unit at least 30 ft. (9.1 m) from the fuel container and

the fueling site before starting the engine.

CAUTION: For proper engine operation and maximum

reliability, pay strict attention to the oil and fuel mixing

instructions on the 2-cycle oil container. Using improperly

mixed fuel can severely damage the engine.

Thoroughly mix the proper ratio of 2-cycle engine oil with unleaded

gasoline in a separate fuel can. Use a 40:1 fuel/oil ratio. Do not mix

them directly in the engine fuel tank. See the table below for specific

gas and oil mixing ratios.

NOTE: One gallon (3.8 liters) of unleaded gasoline mixed with one

3.2 oz. (95 ml) bottle of 2-cycle oil makes a 40:1 fuel/oil ratio.

NOTE: Dispose of the old fuel/oil mix according to federal, state and

local regulations.

Unleaded gasoline* 2=cycle oil

1 gallon U.S. 3.2 ft. oz.

(3.8 liters} (95 ml}

1 liter 25 ml

MiXiNG RATIO - 40:1

WARNING: Avoid accidental starting. Make sure you are

in the starting position when pulling the starter rope (Fig. 6).

To avoid serious injury, the operator and unit must be

in a stable position while starting.

ThrotUe Control

Start/On (I) On/Off Control

STARTING iNSTRUCTiONS

1. Mix gasoline with oil. Refer to Oil and Fuel Mixing Instructions.

2. Fill the fuel tank. Refer to Fueling the Unit.

NOTE: There is no need to turn the unit on. The On/Off Control is in

the ON ( I ) position at all times (Fig. 4).

3. Fully press and release the primer bulb 10 times, slowly. Some

amount of fuel should be visible in the primer bulb (Fig. 5). If fuel

can not be seen in the bulb, press and release the bulb until fuel

is visible.

4. Move the choke lever to Position 1 (Fig. 5).

5. Stand in the starting position (Fig. 6). Hold the handlebar and

squeeze the throttle contol with one hand. Hold the starter rope

with the other hand. Use one foot to hold the wheels in place.

NOTE: Always tilt the unit back slightly to bring the tines off the

ground when starting the unit (Fig. 6).

6. SQUEEZE and HOLD the throttle control for ALL further steps.

Pull the starter rope 5 times.

7. Continue to squeeze the throttle control. Move the choke

lever to Position 2 (Fig. 5).

8. Continue to squeeze the throttle control. Pull the starter rope

3-5 times to start the engine.

9. Continue to squeeze the throttle control. Allow the engine to

warm up for 30-60 seconds.

10. Continue to squeeze the throttle control. Move the choke

lever to Position 3 (Fig. 5).

11. Continue to squeeze the throttle control. Run the unit for an

additional 60 seconds to complete the warm-up. The unit may

be used during this step.

NOTE: The unit is properly warmed up when the engine accelerates

without hesitation.

IF... The engine hesitates, return the choke lever to Position 2 and

continue the warm-up.

IF... The engine does not start, go back to step 3.

IF... The engine fails to start after 2 attempts, move the choke lever

to Position 3 and squeeze the throttle control. Pull the starter

rope 3=8 times in a controlled and steady motion. The engine

should start. If not, repeat.

IF WARM... If the engine is already warm, go back to step 7.

Position

Position 2

Position 3

Starting Position

Starter Rope

Stop/Off (O)

Fig. 4

Fig. 5

Bulb

Throttle

Control

Fig. 6

STOPPING iNSTRUCTiONS

1. Release the throttle control. Allow the engine to cool down by idling.

2. Press and hold the On/Off Control in the OFF (O) position until

the unit comes to a complete stop (Fig. 4).

WARNING: Dress properly to reduce the risk of injury

when operating this unit. Do not wear loose clothing or

jewelry. Wear eye and ear/hearing protection. Wear heavy

long pants, boots and gloves. Do not wear short pants,

sandals or operate barefoot.

OPERATING TiPS

Refer to Moving the Unit.

_h_ AUTION: To prevent serious personal injury, never

pick-up or carry the unit while the engine is running.

2. Start the unit as described in the Starting Instructions.

3. With the tines off the ground, squeeze the throttle control to

increase the engine speed.

4. Hold the handlebar firmly with both hands and slowly lower the

unit until the tines make contact with the ground (Fig. 7).

5. As cultivating action begins, pull back on the cultivator so that

the tines can penetrate the ground.

Move the cultivator to the work area prior to starting the engine.

]

_ ARNING: To prevent serious personal injury, use extreme _

caution when reversing or pulling the unit towards you.

6. Once the ground has been broken, continue at a moderate pace

until you are familiar with the controls and the handling of the

cultivator.

7. Pull the cultivator backwards to improve the depth of cultivation

and reduce your effort.

8. If the tines are digging too deep or not deep enough, adjust

them according to Adjusting Tine Depth.

Fig. 7

ADJUSTING THE TINE DEPTH

The tines should penetrate most garden soils approximately 4 to 6

inches. If necessary, adjust the tines as follows:

1. Stop the engine and allow it to cool. Grasp the spark plug wire

firmly and pull the cap from the spark plug.

2. Raise the wheel height for shallower tine penetration or lower

the wheel height for deeper tine penetration. Refer to Adjusting

the Wheel Assembly in the Assembly Instructions section.

3. Reconnect the spark plug wire and continue use.

MOVING THE UNiT

WARNING: To prevent serious personal injury, always

stop the engine when operation is delayed or when moving

the unit from one location to another.

1. Stop the engine.

2. Tilt the unit back until the tines clear the ground.

3. Push or pull the unit to the next location.

WARNING" To prevent serious injury, never perform

maintenance or repairs with unit running. Always service

and repair a cool unit. Disconnect the spark plug wire to

ensure that the unit cannot start.

MAINTENANCE SCHEDULE

Perform these required maintenance procedures at the frequency

stated in the table. These procedures should also be a part of any

seasonal tune-up.

NOTE: Some maintenance procedures may require special tools or

skills. If you are unsure about these procedures, take your unit

to any non-road engine repair establishment, individual or

authorized service dealer.

NOTE: Maintenance, replacement, or repair of the emission control

devices and system may be performed by any non-road engine

repair establishment, individual or authorized service dealer.

NOTE: Please read the California/EPA statement that came with the

unit for a complete listing of terms and coverage for the emissions

control devices, such as the spark arrestor, muffler, carburetor, etc.

FREQUENCY MAINTENANCE REQUIRED SEE

Every 10 hours Clean and re-oil the air filter p. 11

Every 25 hours Check the spark plug condition and gap p. 12

TINE REMOVAL AND REPLACEMENT

I _, ! WARNING: To prevent serious personal injury, alway s

wear heavy gloves when handling the tines.

NOTE: All installation instructions are explained from the operating

position.

All 4 tines should be replaced at the same time because they will

wear evenly through normal use. Work on one side at a time.

1. Stop the engine and allow it to cool. Grasp the spark plug wire

firmly and pull the cap from the spark plug.

2. Lay the cultivator back on a flat level surface with the handles

touching the ground so that the cultivator is in a horizontal position.

NOTE: It may be necessary to wash any dirt off the tines and shaft

for easier tine removal.

3. Remove the cotter pins from each end of the tine shaft (Fig. 9).

Slide the tines off of the shaft (Fig. 8).

4. Clean and oil the shaft.

5. Slide on the new tines with the hubs facing in towards each

other (Fig. 8). Making sure that the rotation arrows are facing the

gearbox when installing the tines on left tine shaft and away

from the gearbox for the right tine shaft. (Fig. 9)

6. Secure the new tines to the shaft with cotter pins (Fig. 9).

7. Reconnect the spark plug wire.

Tines

Right

Tine Shaft

Hubs

Rotation Arrow

_ Tines

Left

Tine Shaft

Gearbox Hubs

Fig. 8

Cotter Pin

Fig. 9

AiR FILTER MAINTENANCE

Cleaning the Air Filter

Failure to maintain your air filter properly can result in poor

performance or can cause permanent damage to your engine.

1. Open the air filter cover by unscrewing the cover screw (Fig. 10).

2. Remove the air filter and the screen that sits behind it (Fig. 10).

3. Wash the filter in detergent and water. Rinse the filter thoroughly

and allow it to dry.

4. Apply enough clean SAE 30 motor oil to lightly coat the filter.

5. Squeeze the filter to spread and remove excess oil.

6. Replace the air filter and the screen that sits behind it (Fig. 10).

NOTE: Operating the unit without the air filter will VOiD the warranty.

7. Reinstall the air filter cover, insert the hooks on the air filter

housing into the slots on the air filter cover (Fig. 11).

8. Swing the air filter cover to the right and align the cover screw

with the cover screw hole (Fig. 11). Tighten the cover screw to

secure the air filter cover.

NOTE: Do not over tighten as this may strip the screw.

Air Filter Cover

Cover Screw

Slots

Screen

Air Filter

Fig. 10

Air Filter

Housing

Cover

Hooks Screw Hole

iDLE SPEED ADJUSTMENT

IAIw o.,.O: heti es a tu n u in ' 'es ee I

adjustments. Wear protective clothing and observe all

safety instructions to prevent serious personal injury.

NOTE: Careless adjustments can seriously damage your unit. An

authorized service dealer should make carburetor adjustments.

If after checking the fuel mixture and cleaning the air filter the engine

still will not idle, adjust the idle speed screw as follows:

1. Start the engine and let it run for about 2-3 minutes at a high

speed (full throttle) to warm up. Refer to the Starting and

Stopping Instructions.

NOTE: Ensure the tines are not in contact with the ground when

adjusting the idle.

2. Release the throttle control and let the engine idle. If the engine

stops, use a small Phillips screwdriver to turn the idle speed

screw clockwise, 1/8 of a turn at a time (as needed) until the

engine idles smoothly (Fig. 12).

NOTE: The tines should not rotate during engine idle.

3. If the tines rotate when the engine idles, turn the idle speed

screw counterclockwise 1/8 of a turn at a time (as needed), to

reduce idle speed.

Checking the fuel mixture, cleaning the air filter, and adjusting the

idle speed screw should solve most engine problems. If not and all

the following are true:

• The engine will not idle

The engine hesitates or stalls on acceleration

There is a loss of engine power

Have the carburetor adjusted by an authorized service dealer.

Air Filter

Cover

Idle Speed Screw

Fig. 11

Fig. 12

Air Filter

Housing

REPLACING THE SPARK PLUG

1. Stop the engine and allow it to cool. Grasp the spark plug wire

firmly and pull the cap from the spark plug.

2. Clean dirt from around the spark plug. Remove the spark plug from

the cylinder head by turning a5/8 in.socket counterclockwise.

_ ARNING: Do not sand blast, scrape or clean

electrodes. Grit in the engine could damage the cylinder.

3. inspect the spark plug. if the spark plug is cracked, fouled or

dirty, replace it with a replacement part #753=06193,

Champion@ RDJ7J or equivalent spark plug.

4. Use a feeler gauge to set the air gap at 0.025 in. (0.635 ram}

(Fig. 22).

5. install the spark plug in the cylinder head. Tighten the spark plug

with a 5/8-inch socket, turning it clockwise until snug.

NOTE: if using a torque wrench, torque to:

110=120 in.olb. (12.3-13.5 Nora). Do not over tighten.

6. Reconnect the spark plug wire.

0.025 in.

(0.635 ram)

Fig. 13

WARNING: To avoid serious personal injury, always turn

your unit off and allow it to cool before you clean or service it.

CLEANING

Use a small brush to clean off the outside of the unit and to keep

the air vents free of obstructions.

Do not use strong detergents or petroleum based cleaners, like

kerosene. Some household cleaners contain aromatic oils such

as pine and lemon that can damage the plastic housings or

handles. Wipe off any moisture with a soft cloth.

STO RAG E

• Never store a fueled unit where fumes may reach an open flame

or spark.

Allow the engine to cool before storing.

Store the unit in a locked up area to prevent

unauthorized use or damage.

Store the unit in a dw, well-ventilated area.

Store the unit out of the reach of children.

Long=term Storage

1. Remove the fuel cap, tip the unit and drain the fuel into an

approved container.

NOTE: Do not use gasoline that has been stored for more than 30

days. Dispose of old gasoline in accordance with federal, state

and local regulations.

2. Start the engine and allow it to run until it stalls. This ensures

that all fuel has been drained from the carburetor.

3. Allow the engine to cool. Remove the spark plug and put 5

drops of any high quality motor oil or 2-cycle oil into the cylinder.

Pull the starter rope slowly to distribute the oil. Reinstall the

spark plug.

NOTE: Remove the spark plug and drain all of the oil from the

cylinder before attempting to start the unit after storage.

4. Thoroughly clean the unit and inspect for any loose or damaged

parts. Repair or replace damaged parts and tighten loose

screws, nuts or bolts. The unit is ready for storage.

CAUSE

Emptyfueltank

Engineisflooded

Fouledsparkplug

Thefuelisold(over30days)and/orimproperlymixed

ACTION

Fillfueltankwithproperlymixedfuel

Placechokeleverintoposition3,squeezethethrottletriggerand

pullthestarterrope

Replaceorcleanthesparkplug

Drainthefueltankandaddfresh,properlymixedfuel

i !_i@ !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!Li!!!_ _ _

Dirty air filter

Fouled spark plug

Clean or replace the air filter

Replace or clean the spark plug

if further assistance is required, contact your authorized service dealer.

MANUFACTURER'S LiMiTED WARRANTY FOR:

The limited warranty set forth below is given by MTD LLC (MTD) with respect to new merchandise purchased and used in the United States,

its possessions and territories.

MTD warrants this product against defects in material and workmanship for a period of two (2) years commencing on the date of original

purchase and will, at its option, repair or replace, free of charge, any part found to be defective in material or workmanship. This limited

warranty shall only apply if this product has been operated and maintained in accordance with the Operator's Manual furnished with the

product, and has not been subject to misuse, abuse, commercial use, neglect, accident, improper maintenance, alteration, vandalism, theft,

fire, water or damage because of other peril or natural disaster. Damage resulting from the installation or use of any accessory or attachment

not approved by MTD for use with the product(s) covered by this manual will void your warranty as to any resulting damage. This warranty is

limited to ninety (90) days from the date of original retail purchase for any MTD product that is used for rental or commercial purposes, or

any other income-producing purpose.

HOW TO OBTAIN SERVICE: Warranty service is available, WiTH PROOF OF PURCHASE THROUGH YOUR LOCAL AUTHORIZED SERVICE

DEALER. To locate the dealer in your area, visit our website at www.mtdproducts.com or www.mtdproducts.ca, check for a listing in the

Yellow Pages, call 1-800-800-7310 or 1-800-668-1238 in Canada, or write to RO. Box 361131, Cleveland, OH 44136-0019. No product returned

directly to the factory will be accepted unless prior written permission has been extended by the Customer Service Department of MTD.

This limited warranty does not provide coverage in the following cases:

A. Tune-ups - Spark Plugs, Carburetor Adjustments, Filters

B. Wear items - Bump Knobs, Outer Spools, Cutting Line, Inner Reels, Starter Pulley, Starter Ropes, Drive Belts, Saw Chains, Guide Bars,

Cultivator Tines.

C. MTD does not extend any warranty for products sold or exported outside of the United States of America, its possessions and territories,

except those sold through MTD's authorized channels of export distribution.

MTD reserves the right to change or improve the design of any MTD Product without assuming any obligation to modify any product

previously manufactured.

No implied warranty, including any implied warranty of merchantability or fitness for a particular purpose, applies after the

applicable period of express written warranty above as to the parts as identified. No other express warranty or guaranty, whether

written or oral, except as mentioned above, given by any person or entity, including a dealer or retailer, with respect to any product

shall bind MTD. During the period of the Warranty, the exclusive remedy is repair or replacement of the product as set forth above.

(Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.)

The provisions as set forth in this Warranty provide the sole and exclusive remedy arising from the sales. MTD shall not be liable for

incidental or consequential loss or damages including, without limitation, expenses incurred for substitute or replacement lawn

care services, for transportation or for related expenses, or for rental expenses to temporarily replace a warranted product. (Some

states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.)

In no event shall recovery of any kind be greater than the amount of the purchase price of the product sold. Alteration of the safety features

of the product shall void this Warranty. You assume the risk and liability for loss, damage, or injury to you and your property and/or to others

and their property arising out of the use or misuse or inability to use the product.

This limited warranty shall not extend to anyone other than the original purchaser, original lessee or the person for whom it was purchased

as a gift.

How State Law Relates to this Warranty: This warranty gives you specific legal rights, and you may also have other rights which vary from

state to state.

To locate your nearest service dealer, dial 1-800-800-7310 in the United States or 1-800-668-1238 in Canada.

MTD LLC

P.O. Box 361131

Cleveland, OH 44136-0019

Manuel de L'utilisateur

Cultivateur de Jardin & 2-temps

Y125

TABLE DES MATII_RES

Service technique ..................................... 17

Consignes de securit6 .................................. 18

Familiarisez-vous avec votre appareil ...................... 21

Caracteristiques ...................................... 21

instructions de montage ................................ 22

Informations sur I'huile et le carburant ..................... 23

instructions de demarrage et d'arr_t ....................... 24

Mode d'emploi ....................................... 25

Entretien et reparations ................................. 26

Nettoyage et entreposage ............................... 29

Tableau de depannage ................................. 30

Garantie ............................................. 32

CONSERVEZ CES INSTRUCTIONS

NE RAMENEZ PAS CET APPAREIL CHEZ LE DI_TAILLANT.

UNE PREUVE D'ACHAT SERA EXIGI_E POUR TOUTE

PRISE EN CHARGE DANS LE CADRE DE LA GARANTIE.

Si vous eprouvez des difficultes & assembler ce produit ou si vous

avez des questions sur les commandes, I'utilisation ou I'entretien de

cet appareil, veuillez contacter le service & la clientele en composant

le 1-800-800-7310 aux €:tats-Unis ou le 1-800-668-1238 au Canada.

Des informations supplementaires sont disponibles sur notre site

web : www.mtdproducts.com ou www.mtdproducts.ca.

Pour un entretien ou une reparation, veuillez appeler le service

clientele pour obtenir une liste complete des professionnels agre6s

pros de chez vous. L'entretien de cet appareil doit _tre confie

exclusivement & un professionnel agre6 pendant et apr_s la periode

de garantie. Utilisez uniquement des pieces de rechange identiques.

Toutes les informations, illustrations et specifications contenues dans

ce manuel tiennent compte des dernieres informations techniques

disponibles au moment de mettre sous presse. Nous nous reservons

le droit d'y apporter des modifications & tout moment, sans preavis.

769=06986 PO0 08/11

Les symboles de securit6 attirent votre attention sur des dangers

potentiels. Ces symboles et leurs details explicatifs meritent que

vous les lisiez et compreniez bien. Les avertissements de

securit6 ne peuvent eviter les dangers de par eux-m_mes. Les

consignes ou mises en garde qu'ils donnent ne remplacent pas

des mesures preventives appropriees contre les accidents.

j SYMBOLE SIGNIFICATION

_ ANGER : Signale un risque EXTREME.

Le non respect d'une consigne de securit6 relative & un

signal de DANGER entrainera des blessures graves ou

mortelles pour vous-m_me ou pour les autres.

_ VERTISSEMENT : Signale un risque GRAVE.

Le non respect d'un AVERTISSEMENT de securit6 PEUT

entrainer des blessures graves pour vous-m_me ou pour

les autres.

_ TTENTION • Signale un risque MOYEN.

Le non respect d'une consigne de signal d'ATTENTION

PEUT entrainer des deg&ts materiels ou des blessures

graves pour vous-m_me ou pour les autres.

REMARQUE • donne des informations ou des instructions vitales

pour le fonctionnement ou I'entretien de I'equipement.

PARE-ETINCELLES

REMARQUE :_ I'intention des utilisateurs operant darts les terres

foresti_res des Etats-Unis et darts les _tats de Californie, du

Maine, de I'Or_gon et de Washington. Toutes les terres forestieres

des I_tats-Unis et de I'etat de Californie (Codes sur les ressources

publiques 4442 et 4443), de I'Oregon et de Washington exigent de

par la Ioi que certains moteurs & combustion interne utilises darts des

zones couvertes de taillis ou d'herbe soient equip6s d'un pare-

etincelles en parfait etat de fonctionnement, ou qu'ils soient congus,

equip6s et entretenus pour la prevention des incendies. Renseignez-

vous aupr_s des autorites de votre province ou de votre municipalite

concernant la reglementation en vigueur. Vous pourriez _tre passible

d'une amende ou _tre tenu responsable si vous ne respectez pas

cette reglementation. Cet appareil est _quip_ d'un pare-_tincelles

en usine. Si I'_cran pare-_tincelles, r_f. 753-06792, doit _tre

remplace, communiquez avec le service technique.

PROPOSiTiON DE LOI 65 DE CAUFORNIE

AVERTISSEMENT : La fumee d'echappement du

moteur, certains constituants et composants finis

contiennent ou emettent des produits chimiques connus

de I'€:tat de Californie comme etant &I'origine de cancers,

de malformations congenitales ou autres anomalies de la

reproduction. Lavez-vous les mains apr_s manipulation.

Lisez le(s} manuel(s} de I'utilisateur et suivez tousles

avertissements et consignes de s_curit& Vous pourriez _ d6faut

entrafner des blessures graves pour vous ou d'autres personnes.

Sl VOUS AVEZ DES QUESTIONS, APPELEZ LE 1=800=800=

7310 AUX ETATS=UNIS, OU LE 1=800=668=1238 AU CANADA.

• IMPORTANTES CONSIGNES DE S¢:CURIT¢: •

LIRE TOUTES LES iNSTRUCTiONS AVANT UTILISATION

I'1

AVERTISSEMENT : Lors de I'utilisation de I'appareil,

vous devez suivre les consignes de s6curite. Veuillez life ces

consignes avant d'utiliser I'appareil afin de garantir votre

s6curite et celle des personnes &proximite. Conservez-les

pour vous y ref6rer ulterieurement.

Veuillez life les instructions avec soin. Familiarisez-vous avec les

commandes et I'utilisation correcte de cet appareil.

N'utilisez pas I'appareil si vous 6tes fatigue, malade ou sous

I'effet de I'alcool, de drogues ou de medicaments.

Les enfants et adolescents de moins de 15 arts ne doivent pas

utiliser I'appareil exceptes les adolescents assistes d'un adulte.

Inspectez I'appareil avant utilisation. Remplacez les pieces

endommagees. Regardez s'il y a des fuites de carburant. Assurez-

vous que les fixations sont solidement en place. Remplacez les

pieces qui sont fendillees, ebr6ch6es ou endommagees. N'utilisez

pas I'appareil avec des pieces desserrees ou endommagees.

Soyez conscient des risques de blessure &la t6te, aux mains et

aux pieds.

Appuyez sur la manette des gaz et assurez-vous qu'elle revient

automatiquement en position de ralenti. Procedez & tousles

reglages ou reparations avant d'utiliser I'appareil.

€:loignez enfants, spectateurs et animaux de la zone. Tenez-les

au moins 15 m (50 pi) de I&mais sachez que les spectateurs

risquent quand m6me d'6tre atteints par des objets projetes.

Conseillez-leur de porter des protecteurs oculaires. Arr6tez

immediatement I'appareil si quelqu'un s'approche de vous.

AVERTISSEMENTS DE S¢:CURIT¢: CONCERNANT

L'APPAREIL A GAZ

AVERTISSEMENT : L'essence est extr6mement J

inflammable et ses vapeurs peuvent exploser si on y met le

feu. Veuillez prendre les precautions suivantes "

• Stockez uniquement le carburant darts des conteneurs prevus

specifiquement & cet effet et approuves pour le stockage de

telles substances.

Coupez toujours le moteur et laissez-le refroidir avant de remplir

le reservoir d'essence. Ne retirez jamais le bouchon du reservoir

d'essence et ne remplissez jamais ce dernier Iorsque le moteur

est chaud. Devissez lentement le bouchon du reservoir d'essence

afin de reduire la pression avant de le remplir. Ne fumez pas.

Toujours melanger et ajoutez le carburant darts un endroit bien

a6re et propre, en plein air, & I'abri des sources d'etincelles ou

flammes vives. Ne fumez pas.

Ne demarrez jamais I'appareil sans avoir bien revisse le bouchon

du reservoir d'essence.

€:vitez tout ce qui pourrait enflammer le carburant renverse.

L'essence s'etant 6chappee de I'appareil doit 6tre essuyee

immediatement avant de demarrer I'appareil. l_loignez I'appareil

d'au moins 9,1 m (30 pieds) du site et de la source du carburant

avant de demarrer le moteur. Ne fumez pas.

L'appareil ne doit pas 6tre demarr6 ou utilise &I'interieur d'un

espace ou d'un b_timent clos. Inhaler les fumees du pot

d'echappement peut provoquer la mort. Cet appareil doit

fonctionner uniquement en exterieur, darts une zone bien a6ree.

PENDANT L'UTILISATION DE L'APPAREIL

Portez des lunettes de s6curite conformes aux normes ANSi

Z87.1-1989 ainsi que des prot_ge-oreilles durant I'utilisation de

I'appareil. Portez un masque facial ou antipoussieres si vous

travaillez darts un lieu poussiereux.

Portez des pantalons epais et longs, des bottes, des gants et

une chemise & manches Iongues. Ne marchez pas pieds nus et

evitez les pantalons courts et les sandales.

Pour reduire le risque de blessure dO & des objets happes par des

pieces rotatives, evitez de porter des v6tements I&ches, des bijoux

ou des foulards, etc. Relevez les cheveux au-dessus des epaules.

N'utilisez I'appareil qu'en plein jour ou avec un bon eclairage artificiel.

Toutes les surfaces exterieures doivent 6tre exemptes d'huile et

de carburant.

Cet appareil est muni d'un embrayage. Les dents restent

immobiles Iorsque le moteur est au ralenti. Si ce n'est pas le

cas, faites regler I'appareil par un technicien agr6e.

Avant de demarrer I'appareil, assurez-vous que les dents ne

touchent aucun objet.

€:vitez tout demarrage accidentel. Mettez-vous en position de

demarrage chaque fois que vous tirez sur la corde de

demarrage. L'operateur et I'appareil doivent tous deux 6tre en

position stable & ce moment-I&. Voir les Instructions de

demarrage et d'arr6t.

Ne vous etirez pas. Tenez-vous toujours bien sur vos pieds en

position d'equilibre.

Ne forcez pas I'appareil. II posera moins de risques de blessures

et fonctionnera mieux & la vitesse pour laquelle il a et6 congu.

Soyez tr_s prudent Iorsque vous faites marche arriere ou que

vous tirez I'appareil vers vous.

Ne vous etirez pas et faites tr_s attention sur des pentes

abruptes. Tenez-vous toujours en equilibre.

Tenez toujours I'appareil des deux mains Iorsqu'il est en marche.

Agrippez fermement les deux poignees du guidon.

Gardez les mains, le visage et les pieds eloign6s des pieces

mobiles. Ne touchez pas les dents et n'essayez pas de les

arr6ter Iorsqu'elles tournent. Ne faites pas fonctionner I'appareil

sans les protections.

Ne touchez pas le moteur, le silencieux ou la boite

d'engrenages. Ces pieces deviennent tr_s chaudes

I'utilisation. Elles restent chaudes brievement apr_s I'arr6t.

Ne faites pas tourner le moteur & un regime superieur & celui

necessaire pour la t&che. Ne faites pas tourner le moteur a haut

regime Iorsqu'il ne sert pas.

Arr6tez toujours le moteur Iorsque vous suspendez la coupe ou

Iorsque vous vous deplacez d'un lieu de travail vers un autre.

Arr6tez le moteur en cas d'entretien, de reparation, d'installation

ou de retrait des dents. L'appareil et les dents doivent 6tre

arr6t6s pour eviter toute blessure.

Les dents deviennent tr_s tranchantes & I'usage. Portez toujours

des gants Iorsque vous manipulez, retirez, installez ou nettoyez

les dents.

N'utilisez que des pieces de equipement original rechange et

accessoires d'origine pour cet appareil. Elles sont disponibles

aupr_s de votre concessionnaire agre6. L'utilisation de pieces ou

accessoires autres que ceux de eqiupement original peut causer

des blessures graves, endommager I'appareil et annuler sa garantie.

Gardez I'appareil exempt d'accumulation de veg6tation ou

autres matieres. Celles-ci peuvent rester Iogees entre les dents,

la boite d'engrenages ou le protecteur.

Afin de diminuer les risques d'incendie, remplacez tout

silencieux ou pare-etincelles defectueux et conservez le moteur

et le silencieux exempts d'herbe, de feuilles et d'accumulation

excessive de graisse ou de carbone.

AUTRES AVERTISSEMENTS DE SC:CURIT¢:

,i, N'entreposez jamais I'appareil rempli de carburant dans un

edifice ou les vapeurs peuvent atteindre une source de flammes

vives ou d'etincelles.

Laissez le moteur se refroidir avant de I'entreposer ou de le

transporter. Attachez bien I'appareil pendant le transport.

Rangez I'appareil dans un endroit verrouille et sec, ou elev6 et

sec, hers de portee des enfants, pour eviter une utilisation

indesirable ou un accident.

Ne trempez et n'arrosez jamais I'appareil avec de I'eau ou tout

autre liquide. Gardez les poignees s_ches, propres et exemptes

de debris. Nettoyez apr_s chaque usage. Voir les sections

Nettoyage et Entreposage.

Conservez ces instructions. Consultez-les souvent et

servez-vous en pour instruire d'autres usagers. Si vous pr6tez

I'appareil a quelqu'un, pr_tez-lui egalement ces instructions.

CONSERVER CES iNSTRUCTiONS

• SYMBOLES DE SC:CURIT¢: ET INTERNATIONAUX •

Ce manuel de I'utilisateur decrit les symboles et pictogrammes de securit6 et internationaux pouvant appara_tre sur ce produit. Consultez le

manuel de I'utilisateur pour les informations concernant la securit6, le montage, le fonctionnement, I'entretien et les reparations.

SYMBOLE SIGNIFICATION

_ _ . SYMBOLE ALERTE DE S¢:CUR,TI_

Indique un danger, un avertissement ou une mise en

garde. Ce symbole peut _tre combin6 & d'autres

symboles ou pictogrammes.

o LISEZ LE MANUEL DE L UTILISATEUR

AVERTISSEMENT : LJsezle manuel de I'utilisateur

et suivez tousles avertissements et consignes de

. s6curit6. Vous pourriez &d6faut entrainer des blessures

graves pour vous ou d autres personnes.

I o PORTEZ DES PROTECTIONS (YEUX ET OREILLES)

AVERTISSEMENT : les objets projet6s,et les

bruits forts peuvent endommager la vue et I oui'e.

Portez une visi_re de norme ANSI Z87.1-1989 et des

prot_ge-oreilles pendant I utilisation.

_'_L_ " CARBURANT SANS PLOMB

Utilisez toujours du carburant sans plomb frais et propre.

_ • NIVEAU D HUILE

Voir le manuel de I'utilisateur pour le type d'huile

appropri6.

o 'UTILISEZ PAS D'ESSENCE E85 DANS GET

APPAREIL

AVERTISSEMENT : II a 6t6 prouv_ que

'""_1utilisation de carburant contenant plus de 10%

d'6thanol endommagera tr_s certainement ce moteur

. et annulera la garantie.

o COMMANDE MARCHF/ARRf=T

I I ALLUMAGE/Dc:MARRAG E/MARCH E

• COMMANDE MARCHE/ARR_;T

U J ARRFTouSTOP

_ ,,POMPE D'AMORGAGE

!J_ I Appuyez 10 fois, lentement et 9.fond, sur la pompe

. d amorgage.

H I_1 I11 " ETRANGLEUR

1 • Position d 6tranglement MAXIMUM

• " " "

2 Position d etranglement PARTIEL

• 3 • Position de MARCHE

SYMBOLE SIGNIFICATION

A , _=LOIGNEZ LES SPECTATEURS

AVERTISSEMENT : 6ioignez tout SPectateUr, les

enfants et les animaux domestiques en paFticuiier,

dlau moins 15 m(50 pi)de !azone de Coupel

_Q,.= , LES OBJETS PROJETES ET LA T_=TE ROTATIVE

_2_d_ PEUVENT CAUSER DES BLESSURES GRAVES

_! AVERTISSEMENT: ne fa!tespas f0nctienner

_/_'4 _" sans protecteur de s6curit6 en plastique. Tenez.vous

_.I'_cart deFaccessoire de COupe i0tatif,

,SURFACE CHAUDE

_ AVERTISSEMENT: Ne t0Uchez Pas UnSiienCieUX

ou un cylindre chaud, Vous pourriez vous brQler: Ces

;i pi_ces deviennent tr_s chaudes 9.1utilisation, E!!es

testes chaudes bd_vement apr_s !'arr_t.

PEUVENT BLESSER GRI_=VEMEN T

W AV =FmSS =MENTArr6teziemoteUretaSSez

leS dents -'sarr_ter avant d-"eninsta!ler oU en retirer, oU

d'entreprendre un nettoyage ou entretien. Gardez les

. mains et !es pieds _loign_s des dents en rotation.

i i i

, NE PAS MARCHER

Tenez-V0us toujours en _quilib_el Ne voUs _tirez paS

et faites tr_s attention IorSque vouS travai!!ez sUrdes

pentes ou inclinaisons abruptes.

, PLACER LE PIED DROIT ICI

€:vitez tout d_mairage accidentel. Mettez_vous en

position de d_marrage chaque fois que v0us tirez sur

la C0rde de d_marrage: L apparel! et v0us devez _tre

en position stable:

La page est en cours de chargement...

ACE 21AK125G900 Le manuel du propriétaire

Marque: ACE

Modèle: 21AK125G900

Catégorie: Mini motoculteurs

Taper: Le manuel du propriétaire

Ce manuel convient également à

7306699

Télécharger le PDF

rapport

dans d''autres langues

English: ACE 21AK125G900 Owner's manual
español: ACE 21AK125G900 El manual del propietario

Documents connexes

ACE 7214950 Le manuel du propriétaire

ACE 21AK125G900 Le manuel du propriétaire

Ce manuel convient également à

ACE 21AK125G900 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents