Tripp Lite SmartOnline SUINT3000RTXL2U Le manuel du propriétaire

1

Owner’s Manual

SmartOnline

®

Rack/Tower On-Line UPS Systems

Not suitable for mobile applications.

1. Important Safety Instructions 2

2. Installation 3

2.1 Mounting (Rack) 3

2.2 Mounting (Tower) 4

2.3 Connection and Start-Up 4

2.4 Optional Connections 5

3. Operation 8

3.1 Front Panel Switches 8

3.2 Advanced Operational 8

Settings

3.3 Front Panel Indicator Lights 9

3.4 Rear Panel 11

3.5 Communications 12

4. Troubleshooting 13

5. Battery Replacement 14

6. Storage and Service 16

6.1 Storage 16

6.2 Service 16

7. Product Registration and 17

Regulatory Compliance

Español 18

Français 35

Русский

52

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

PROTECT YOUR INVESTMENT!

Register your product for quicker service

and ultimate peace of mind.

You could also win an

ISOBAR6ULTRA surge protector—

a $100 value!

www.tripplite.com/warranty

17-06-040-932882.indb 1 6/29/2017 10:33:09 AM

2

1. Important Safety Instructions

UPS Location Warnings

• Install the UPS system indoors, away from excess moisture or heat, conductive

contaminants, dust or direct sunlight.

• For best performance, keep the indoor temperature between 32º F and 104º F

(0º C and 40º C).

• Leave adequate space around all sides of the UPS system for proper ventilation.

• Do not mount the UPS system with its front or rear panel facing down (at any angle).

Mounting in this manner will seriously inhibit the UPS system’s internal cooling,

eventually causing product damage not covered under warranty.

UPS Connection Warnings

• Connect the UPS system directly to a properly grounded AC power outlet. The outlet

must be installed near the UPS system and must be easily accessible for disconnection.

• To reduce the risk of fire, connect only to a circuit provided with 20 amperes maximum

branch circuit overcurrent protection in accordance with your local and National

Electrical Code (NEC), ANSI/NFPA 70.

• Do not modify the UPS system’s plug, and do not use an adapter that would eliminate

the UPS system’s ground connection. Do not plug the UPS system into itself; this will

damage the UPS system.

• Do not use extension cords to connect the UPS system to an AC outlet.

• If the UPS system receives power from a motor-powered AC generator, the generator

must provide clean, filtered, computer-grade output.

Equipment Connection Warnings

• Use of this equipment in life support applications where failure of this equipment can

reasonably be expected to cause the failure of the life support equipment or to

significantly affect its safety or effectiveness is not recommended.

• Do not connect surge suppressors or extension cords to the output of the UPS system.

This might damage the UPS system and may affect the surge protector and UPS system

warranties. Connecting a Tripp Lite power distribution unit (PDU) to the output of the

UPS system is safe and will not void the warranty.

Battery Warnings

• Refer to Section 5: Battery Replacement for a complete list of battery warnings.

SAVE THESE INSTRUCTIONS

This manual contains instructions and warnings that should be followed during

the installation, operation and storage of this product. Failure to heed these

warnings may affect the warranty.

17-06-040-932882.indb 2 6/29/2017 10:33:15 AM

3

2. Installation

1

2

3

D

E

4

F

C

B

C

B

A

B

A

2.1 Mounting (Rack)

• Use the included rackmount shelves and mounting hardware to mount the UPS system

in a 4-post rack or rack enclosure. To mount the UPS system in a 2-post (telecom) rack,

order Tripp Lite’s 2-Post Rackmount Kit (model 2POSTRMKITWM, sold separately).

• The instructions in this manual are for common rack and rack enclosure types and may

not be appropriate for all mounting applications. The user must determine the fitness of

hardware and procedures before mounting. If hardware or procedures are not suitable

for the application, contact the manufacturer of the rack or rack enclosure for a

solution.

Warning: The UPS system is very heavy—be careful when moving or lifting it.

4-Post Mounting Procedure

1

The included plastic pegs

A

will support the

empty rackmount shelves

B

until the

permanent mounting hardware is installed.

Insert a peg near the center of the front and

rear bracket of each shelf as shown. (Each

front bracket has six holes and each rear

bracket has three holes.) The pegs will snap

into place.

After installing the pegs, expand each shelf to

match the depth of the vertical rack rails. The

pegs will fit through the square holes in the

rack rails to support the shelves. Confirm that

the shelves are level in all directions.

Note: The support ledge of each shelf must face

inward.

2

Secure the shelves

B

to the rack rails

permanently using the longer included screws

and washers

C

as shown. (Place four screws

at the front and four screws at the back.)

Tighten all screws before proceeding.

Warning: Do not attempt to install

the UPS system until the required

screws have been inserted and

tightened. The plastic pegs will not

support the weight of the UPS

system.

3

Attach the mounting brackets

D

to the

forward mounting holes of the UPS system

using the shorter included screws

E

. The

mounting bracket ears must face forward.

4

With the aid of an assistant, lift the UPS system and slide it onto the mounting

shelves. Insert four of the included screws

F

through the mounting bracket ears and

into the vertical rack rails. Tighten all screws securely.

17-06-040-932882.indb 3 6/29/2017 10:33:19 AM

4

1

2

Some models may differ.

1

Voltage Selection Mode

Please follow below procedure to select the

output voltage by front panel.

1. Press the ON/TEST and OFF buttons

simultaneously to enter “Voltage Selection”

mode. The three LEDs labeled VOLTAGE

SELECTION MODE will flash when you have

entered this mode.

2. Press the ON/TEST button to select the

output voltage from 200 to 240.

3. After selecting the desired output voltage,

press the ON/TEST and OFF buttons

simultaneously to save your selection and

exit “Voltage Selection” mode.

2. Installation

2.2 Mounting (Tower)

The UPS system can be mounted in an upright

tower position when used with Tripp Lite’s

optional base stand kit (model 2-9USTAND, sold

separately). When mounting the UPS system in a

tower position, make sure the control panel is

closer to the top of the cabinet than the bottom.

The control panel can be rotated to match the

orientation of the UPS system. Pull the panel

out, rotate it and push it back into place as

shown.

Warning: The UPS system is very

heavy—be careful when moving or

lifting it.

2.3 Connection and Start-Up

1

Plug the UPS system into an electrical

outlet.

Note: The UPS system does not include an input

power cord.

Connect a user-supplied power cord to the

IEC-320-C20 input receptacle. The power

cord should have an IEC-320-C19 connector

on one end and a plug appropriate for your

local site’s utility outlet on the other end.

The UPS system must be connected to a

dedicated circuit of sufficient amperage.

Refer to the UPS system nameplate for input

requirements.

After the UPS system is plugged in, the

following sequence of events will occur:

1. The fan will turn on and all LEDs will

illuminate momentarily.

2. The percent level LEDs (25%, 50%, 75%

and 100%) will illuminate one at a time.

3. The “LINE” and “LOAD” LEDs will

illuminate to indicate normal operation.

Note: Power will not be supplied to the outlets until

the UPS system is turned on.

17-06-040-932882.indb 4 6/29/2017 10:33:21 AM

5

Voltage Note: The UPS system supports a nominal AC voltage setting of 200V, 208V, 220V, 230V

or 240V. 230V is the factory default setting. The full output capacity of 2,500 watts is available

when the UPS system is set at 230V or 240V. When the UPS system is set at 200V, 208V or

220V, output capacity is reduced to 2,400 watts. The nominal voltage setting can be changed

using the control panel buttons, with PowerAlert

®

software or the optional WEBCARDLX internal

accessory card. See the PowerAlert software or WEBCARDLX documentation for more information

about changing the nominal voltage setting.

2

3

Some models may differ.

2. Installation

2

Plug equipment into the UPS system’s AC

outlets.

Note: Use the supplied C13 to C14 interconnection

cord.

The UPS system is designed to support

computer equipment only. The UPS system

will become overloaded if household

appliances or laser printers are connected to

its outlets.

Note: Additional interconnection cords (C13 to

C14) are available from Tripp Lite. Visit www.

tripplite.com. (Part # P004-006)

3

Turn the UPS system ON.

To turn on the UPS system, press the “ON/

TEST” button for approximately one second

until the UPS system beeps, then release the

button.

The UPS system will begin providing AC power

to its outlets. The “ON LINE” LED will

illuminate.

Note: UPS system will function properly upon initial

startup, however, maximum runtime for the unit’s

battery will only be accessible after it has been

charged for 24 hours.

17-06-040-932882.indb 5 6/29/2017 10:33:22 AM

6

4-5

2a

Some models may differ.

2b

1

USB and RS-232 Serial Communications

Use the included USB cable

1a

or RS-232

(DB9) serial cable

1b

to connect the UPS

system’s communication port to a

computer’s communication port. Install the

included PowerAlert software on the

computer. (See the PowerAlert software

documentation for system requirements and

installation instructions.)

2

EPO Port Connection

This optional feature is only for those

applications that require connection to a

facility’s Emergency Power Off (EPO) circuit.

When the UPS is connected to this circuit, it

enables emergency shutdown of the UPS’s

inverter and inhibits transfer to internal

bypass. Using the cable provided, connect

the EPO port of your UPS

2a

to a user-

supplied normally closed or normally open

switch according to the circuit diagram

2b

.

Notes:

1. If using a cable other than what is supplied, the

cable should not have a resistance of greater

than 5 ohms.

2. If a non-latching EPO switch is used, the EPO

must be held for a minimum of 1 second. This

does not apply to a latching EPO switch.

CAUTION: The EPO port is not a

phone line surge suppressor; do

not connect a phone line to this

port.

1b

Some models may differ.

1a

Some models may differ.

2. Installation

2.4 Optional Connections

The UPS system will function properly without these connections.*

* Note: PowerAlert software (included) or the optional WEBCARDLX internal accessory card is required

to control some of the advanced features of the UPS system, including economy mode and frequency

conversion settings. The factory defaults are suitable for most applications.

UPS Unit State when asserting EPO with AC line present:

LEDs Output Fans Serial SNMP USB

OFF OFF ON ON ON ON

To restart the UPS unit after asserting EPO with AC line present:

1. Verify that the EPO assertion has been removed or cleared.

2. Remove AC line power to the UPS unit.

3. Reapply AC line power. Now the UPS will start back up in Standby mode.

17-06-040-932882.indb 6 6/29/2017 10:33:24 AM

7

3

4

Some models may differ.

UPS Unit State when asserting EPO without AC line power:

LEDs Output Fans Serial SNMP USB

OFF OFF OFF OFF OFF OFF

To restart the UPS unit after asserting EPO without AC line power:

1. Verify that the EPO assertion has been removed or cleared.

2. Reapply AC line power to the UPS unit. Now the UPS will start back up in Standby mode.

3

External Battery Connection

4

Accessory Card Slot

The slot accommodates an optional internal

accessory card (model: WEBCARDLX, sold

separately). WEBCARDLX provides an

Ethernet network interface for remote

monitoring and control of the UPS system via

SNMP, Web or telnet. WEBCARDLX enables

remote reboots, shutdowns, load monitoring,

condition reporting and more. Use

WEBCARDLX with an optional environmental

sensor (model E2MT, E2MTDI, E2MTDO and

E2MTHDI, sold separately) to monitor

temperature and humidity or to control and

monitor alarms and security systems.

Remove the cover panel from the slot to

insert the accessory card. Refer to the

WEBCARDLX documentation for additional

installation instructions.

2. Installation

17-06-040-932882.indb 7 6/29/2017 10:33:26 AM

8

3. Operation

3.1 Front Panel Switches

“ON/TEST” Button: This button controls four separate functions:

UPS System Power ON

To turn on the UPS system, press the “ON/TEST” button for

approximately one second until the UPS system beeps, then release

the button. The “ON LINE” LED will illuminate.

UPS System Self-Test

To initiate a self-test of the battery during normal on-line operation,

press this button for approximately one second until the UPS system

beeps, then release it. The UPS system will shift to battery power for

10 seconds.

Note: All LEDs illuminate during a self-test.

Alarm Silence

To silence the UPS system’s on battery alarm, press this button and

hold it until the UPS system beeps, then release the button.

UPS System Cold Start

To use the UPS system as a stand-alone power source when AC

power is unavailable (i.e. during a blackout), press this button and

hold it until the UPS system beeps, then release the button. The

UPS system will then provide battery power to its outlets.*

* The “ON BATT” indicator light will be illuminated since the UPS system will

be operating from battery power.

“OFF” Button: This button turns off power to the UPS system’s

outlets. Press this button and hold it until the UPS system beeps,

then release it. The battery will continue to charge and the fan will

continue to operate even when the outlets are off. To turn the UPS

system off completely, including the battery charger, unplug the UPS

system’s power cord after pressing the “OFF” switch.

3.2 Advanced Operational Settings

Economy Mode

The UPS system supports economy mode operation to reduce energy consumption and

BTU emissions. In economy mode, the UPS system operates with increased efficiency

when the quality of utility power is satisfactory to pass through to connected equipment

without double conversion.

Economy mode saves energy by suspending double conversion when incoming voltage is

within -12%/+10% of the nominal voltage setting. If the nominal voltage setting is 230V,

the UPS system will remain in economy mode while utility line voltage is between

approximately 202V and 253V. If utility line voltage falls outside this range, the UPS

system will either switch back to standard on-line, double conversion mode or it will switch

to battery backup mode, depending on the severity of the voltage deviation.

Economy mode can be enabled (or disabled) through the included PowerAlert software or

the optional WEBCARDLX internal accessory card. The UPS system's yellow “BYPASS” LED

will illuminate continuously when economy mode is enabled. Refer to the PowerAlert or

WEBCARDLX documentation for more information.

17-06-040-932882.indb 8 6/29/2017 10:33:26 AM

9

On-line, double-conversion mode (default)

Typical line efficiency at full load: 89%

Output voltage range: ± 2% of nominal setting (200/208/220/230/240V)

Economy mode

Typical line efficiency at full load: 97%

Output voltage range: -12%/+10% of nominal setting (200/208/220/230/240V)

Frequency Conversion

The UPS system automatically selects 50 Hz or 60 Hz operation based on utility power

conditions at start-up and regulates output power within ± 0.05 Hz of the selected

frequency. The UPS system also has an advanced setting that allows continuous frequency

conversion from 50 Hz to 60 Hz or from 60 Hz to 50 Hz. The advanced frequency

conversion setting is accessible through the included PowerAlert software or the optional

WEBCARDLX internal accessory card. When continuous frequency conversion is enabled,

the maximum output capacity of the UPS system is derated by 25%.

3.3 Front Panel Indicator Lights

Note: All LEDs illuminate during a UPS system self-test.

3. Operation

“ON LINE” LED: This green LED will illuminate continuously to

indicate the UPS system is operating normally in on-line mode

(filtering and resynthesizing AC line input to provide pure sine wave

output). When this LED is illuminated, the load level of the UPS

system is displayed on the % level LEDs (25%, 50%, 75%, 100%).

“LINE” LED: This green LED will illuminate continuously to indicate

the utility-supplied AC line voltage at the wall outlet is nominal. It

will flash if the line voltage is outside the nominal range (either too

low or too high). User action is not required when the LED flashes;

the UPS system continuously and automatically filters AC line

power to provide equipment with pure sine wave AC power,

regardless of brownout or overvoltage conditions. If this LED is off,

then AC line voltage is not present (blackout) or is at an extremely

high voltage, and the UPS system will provide connected

equipment with power from its battery system.

“BYPASS” LED: This yellow LED will illuminate continuously when

the UPS system is in economy mode. The LED will flash when the

UPS system is bypass mode, indicating that the UPS system’s DC/

AC inverter is deactivated. The red “FAULT” LED will also illuminate

if the UPS system is in bypass mode. During normal operation the

bypass LED will illuminate briefly when the unit is plugged in. If an

internal fault or overload occurs, the LED will flash repeatedly to

show that connected equipment will receive filtered AC line power,

but will not receive battery power during a blackout. In this case,

contact Tripp Lite for service.

“FAULT” LED: This red LED will flash when the UPS system detects

an internal fault. If the condition persists after restarting the UPS

system, see Section 4: Troubleshooting.

17-06-040-932882.indb 9 6/29/2017 10:33:27 AM

10

3. Operation

“LOAD” LED: This green LED will illuminate when the UPS system

is receiving AC power. It also indicates that the % level LEDs (25%,

50%, 75%, 100%) are displaying the UPS load level.

“BATT” LED: This green LED will illuminate when the UPS system

is operating from battery power. It indicates that the % level LEDs

(25%, 50%, 75%, 100%) are displaying the battery charge level.

(The “ON BATT” LED will also be illuminated.)

% Level LEDs: These dual-function LEDs will indicate the % level

for either the load level (if the “LOAD” LED is lit) or the battery

charge level (if the “BATT” LED is lit).

“OVERLOAD” LED: This red LED will illuminate continuously to

indicate that the UPS system’s capacity has been exceeded. The

UPS alarm will beep continuously. Immediately unplug some

equipment until the LED and alarm go off. If the overload is not

corrected immediately, the UPS system will go from on-line to

bypass mode.

“BATT LOW” LED: This yellow LED will illuminate when the UPS

system’s battery charge level is low. The UPS alarm will beep until

the batteries are either depleted or adequately recharged.

“ON BATT” LED: This green LED will illuminate continuously to

indicate that AC line voltage is absent (or out of range) and the

UPS system is providing equipment with battery-derived AC power.

The UPS system will also beep every two seconds (unless silenced

by the “ON/TEST” button) and the % level LEDs (25%, 50%, 75%,

100%) will display the battery charge level.

“REPLACE BATT” LED: This red LED will illuminate continuously

and the UPS alarm will beep every two seconds if the UPS system

fails the automatic self-test. Allow the UPS system to charge for at

least 12 hours and perform a self-test as described in Section

3.1: Front Panel Switches. If the condition persists, contact

Tripp Lite.

17-06-040-932882.indb 10 6/29/2017 10:33:29 AM

11

IEC-320-C20

CONTROLLABLE LOAD 1

CONTROLLABLE LOAD 2 UNSWITCHED

IEC-320-C13

IEC-320-C19

3. Operation

3.4 Rear Panel

Accessory Card Slot: Remove the cover panel from this slot to

install an optional internal WEBCARDLX accessory, sold separately.

WEBCARDLX provides a network interface for monitoring and

control via SNMP, Web or telnet, enabling remote reboots,

shutdowns and more.

External Battery Pack Connector

(Configuration Varies By Model)

Fan: The fan cools the UPS system’s internal components. It is

always on when line power is present, even if power to the UPS

system’s outlets is turned off.

Input Power Cord: This UPS system requires a user-supplied

power cord. This power cord should have an IEC-320-C19

connector on one end and a plug appropriate for your local site's

utility outlet on the other end.

AC Outlets (Configuration Varies By Model): These outlets

provide connected equipment with pure sine wave AC output

derived from the AC line during normal operation and derived from

battery power during blackouts and severe brownouts or

overvoltages. Output power is filtered to protect connected

equipment against damaging surges and line noise.

The outlets are divided into numbered load banks, as labelled on

the unit. Using included PowerAlert software and cabling or an

optional WEBCARDLX, load banks may be individually turned off

and on from a remote location, allowing users to reset or reboot

connected equipment.

17-06-040-932882.indb 11 6/29/2017 10:33:32 AM

12

RS-232 (DB9)

3.5 Communications

Communication Ports (USB and/or RS-232): These ports connect

the UPS system to a computer. Use with Tripp Lite’s PowerAlert

software and included cabling to allow the computer to

automatically save open files and shut down during a blackout. Also

use PowerAlert software to control UPS system load banks and

monitor a wide variety of AC line power and UPS system operating

conditions. See Section 2.4: Optional Connections for cable

connection instructions. Refer to the PowerAlert documentation for

software installation instructions.

The RS-232 port can also be used as a contact closure port. The

port’s numbered pin assignments are shown in the RS-232 (DB9)

illustration at left. If the battery charge level is low, the UPS system

will bridge pins 1 and 5. If utility power fails, the UPS system will

bridge pins 8 and 5. To shut down the UPS system remotely, short

pin 3~pin 9 for at least 3.8 seconds.

EPO (Emergency Power Off) Port: The UPS system has an EPO

port that may be used to connect the UPS system to a contact

closure switch to enable emergency UPS system shutdown. See

Section 2.4: Optional Connections for more information. If the

unit has been shut down due to an EPO event, it will be necessary

to disconnect the unit from utility power to reset the unit. After

re-connecting to utility power, see Section 2.3 Installation for

start-up instructions.

USB

3. Operation

17-06-040-932882.indb 12 6/29/2017 10:33:33 AM

13

The UPS system control panel LEDs will illuminate in the sequences listed below to

indicate operational problems.

Note: If the “FAULT” LED illuminates, determine the specific fault condition by activating the error

code LEDs. To activate the error code LEDs, press the “ON/TEST” button until the UPS system beeps,

then release the button. The error code LEDs will illuminate for five seconds.

Illuminated LEDs Condition and Solution

On: REPLACE BATT

Error Code LEDs: Not Applicable

Replace Battery: Allow the UPS system to charge for

at least 12 hours and perform a UPS system self-test as

described in Section 3.1: Front Panel Switches. If the

LED remains on, contact Tripp Lite for service.

Flashing: LINE

Error Code LEDs: Not Applicable

Input Abnormal: Utility power voltage or frequency is too

high or too low for the UPS system to operate in BYPASS

mode. If an inverter failure occurs, the UPS system will

not pass through utility power to the outlets and any

connected equipment will turn off.

On: FAULT

Error Code LEDs: 50% 100%

Battery Weak: Allow the UPS system to charge for 12

hours. If the LED remains on, contact Tripp Lite for service.

On: FAULT

Error Code LEDs: 25% 75%

Inverter Over-Current: Reduce the load supported by the

UPS system by unplugging some equipment. Restart the

UPS system. If the problem persists, contact Tripp Lite for

service.

On: FAULT

Error Code LEDs: 25% 75% 100%

Internal Temperature Too High: Conﬁrm that adequate

space exists for air to circulate near the UPS system’s

vents. Conﬁrm that the UPS system’s fan is working

properly. Conﬁrm that the ambient temperature does not

exceed recommended levels. Restart the UPS system.

On: FAULT

Error Code LEDs: 25% 50%

Inverter Overload: Reduce the load supported by the

UPS system by unplugging some equipment.

On: FAULT

Error Code LEDs: 25% 50% 100%

Charger Out of Order: Restart the UPS system. If the

problem persists, contact Tripp Lite for service.

On: FAULT

Error Code LEDs: 25% 50% 75%

Fan Out of Order: Restart the UPS system. If the problem

persists, contact Tripp Lite for service.

On: FAULT

Error Code LEDs: 25% 50% 75% 100%

Bypass Phase Can’t Lock: Restart the UPS system. If

the problem persists, contact Tripp Lite for service.

On: FAULT

Error Code LEDs: BATT 25%

Utility Voltage Low and Battery Disconnected at

Initialization: Shut down the UPS system. Check the

internal battery connections. Correct the AC input voltage.

Restart the UPS system. If the problem persists, contact

Tripp Lite for service.

On: FAULT

Error Code LEDs: BATT 25% 100%

Battery Disconnected at Initialization and Utility

Voltage or Frequency Too High or Too Low in On-Line

Mode: Shut down the UPS system. Check the internal

battery connections. Correct the AC input voltage. Restart

the UPS system. If the problem persists, contact Tripp Lite

for service.

On: FAULT

Error Code LEDs: BATT 25% 75%

Input Over-Current: Reduce the load supported by the UPS

system by unplugging some equipment. Restart the UPS

system. If the problem persists, contact Tripp Lite for service.

On: FAULT

Error Code LEDs: BATT 25% 50%

Bypass Overload: Reduce the load supported by the UPS

system by unplugging some equipment. Either wait for the

UPS system to recognize the load reduction or restart the UPS

system. If the problem persists, contact Tripp Lite for service.

On: FAULT

Error Code LEDs: BATT 25% 50% 100%

Battery Voltage Too High: Restart the UPS system. If the

problem persists, contact Tripp Lite for service.

Note: All other error codes indicate internal fault conditions. Restart the UPS system. If the problem

persists, contact Tripp Lite for service.

4. Troubleshooting

17-06-040-932882.indb 13 6/29/2017 10:33:33 AM

14

Under normal conditions, the original batteries in the UPS system will last several years.

The batteries are designed for hot-swap replacement (i.e. replacement while the UPS

system is in ON mode), but some qualified service personnel may wish to put the UPS

system in OFF mode and disconnect equipment before proceeding.

Battery Warnings

Caution: There are no user-serviceable parts inside the UPS system. Battery service or

replacement must be performed or supervised by qualified service personnel familiar

with batteries and the required precautions.

Caution: When replacing batteries, replace only with the same type and number of

batteries.

• Batteries can present a risk of electrical shock and burn from high short-circuit current.

Observe proper precautions. Do not dispose of the batteries in a fire. Do not open the

UPS or batteries. Do not short or bridge the battery terminals with any object.

Unplug and turn off the UPS before performing battery replacement. Use tools with

insulated handles. There are no user-serviceable parts inside the UPS. Battery

replacement should be performed only by authorized service personnel using the same

number and type of batteries (Sealed Lead-Acid). The batteries are recyclable.

Refer to your local codes for disposal requirements or visit http://www.tripplite.com/

support/recycling-program for recycling information. Tripp Lite offers a complete line of

UPS System Replacement Battery Cartridges (R.B.C.).Visit Tripp Lite on the Web at

http://www.tripplite.com/products/battery-finder/ to locate the specific replacement

battery for your UPS.

5. Battery Replacement

17-06-040-932882.indb 14 6/29/2017 10:33:33 AM

15

1

2

3

6

5

4

Procedure

1

Remove Front Panel

2

Remove Battery Compartment Cover

3

Disconnect Old

Batteries and Remove Old Batteries

4

Insert New Batteries and Connect New Batteries

(Attach battery connectors black-to-black and red-to-red.)

5

Replace Battery

Compartment Cover

6

Replace Front Panel

7

Recycle Old Batteries

7

5. Battery Replacement

17-06-040-932882.indb 15 6/29/2017 10:33:40 AM

16

6. Storage and Service

6.1 Storage

First turn the UPS system OFF: press the “OFF” switch to turn power off at the UPS

system’s outlets, then disconnect the UPS system’s power cord from the wall outlet. Next,

disconnect all equipment to avoid battery drain. If the UPS system will be stored for an

extended period of time, recharge the UPS system’s batteries fully every three months by

plugging the UPS system into a live AC outlet and allowing the UPS system to charge for

4-6 hours. If the UPS system’s batteries are left discharged for an extended period of time,

they may suffer a permanent loss of capacity.

6.2 Service

A variety of Extended Warranty and On-Site Service Programs are also available from

Tripp Lite. For more information on service, visit www.tripplite.com/support. Before returning

your product for service, follow these steps:

1. Review the installation and operation procedures in this manual to insure that the

service problem does not originate from a misreading of the instructions.

2. If the problem continues, do not contact or return the product to the dealer. Instead,

visit www.tripplite.com/support.

3. If the problem requires service, visit www.tripplite.com/support and click the Product

Returns link. From here you can request a Returned Material Authorization (RMA)

number, which is required for service. This simple on-line form will ask for your unit’s

model and serial numbers, along with other general purchaser information. The RMA

number, along with shipping instructions will be emailed to you. Any damages (direct,

indirect, special or consequential) to the product incurred during shipment to Tripp Lite

or an authorized Tripp Lite service center is not covered under warranty. Products

shipped to Tripp Lite or an authorized Tripp Lite service center must have transportation

charges prepaid. Mark the RMA number on the outside of the package. If the product

is within its warranty period, enclose a copy of your sales receipt. Return the product

for service using an insured carrier to the address given to you when you request the

RMA.

17-06-040-932882.indb 16 6/29/2017 10:33:40 AM

17

PRODUCT REGISTRATION

Visit www.tripplite.com/warranty today to register your new Tripp Lite product. You’ll be automatically entered

into a drawing for a chance to win a FREE Tripp Lite product!*

* No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.

Regulatory Compliance Identification Numbers: For the purpose of regulatory compliance certifications

and identification, this Tripp Lite product has been assigned a unique series number. The series number can

be found on the product nameplate label, along with all required approval markings and information. When

requesting compliance information for this product, always refer to the series number. The series number

should not be confused with the marking name or model number of the product.

FCC Notice, Class A

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)

This device may not cause harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications. Operation of this equipment in

a residential area is likely to cause harmful interference in which case the user will be required to correct the

interference at his own expense. The user must use shielded cables and connectors with this equipment. Any

changes or modifications to this equipment not expressly approved by Tripp Lite could void the user’s authority

to operate this equipment.

WEEE Compliance Information for Tripp Lite Customers and Recyclers (European Union)

Under the Waste Electrical and Electronic Equipment (WEEE) Directive and implementing regulations,

when customers buy new electrical and electronic equipment from Tripp Lite they are entitled to:

• Send old equipment for recycling on a one-for-one, like-for-like basis

(this varies depending on the country)

• Send the new equipment back for recycling when this ultimately becomes waste

Tripp Lite has a policy of continuous improvement. Specifications are subject to change without notice.

7. Product Registration and Regulatory Compliance

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

17-06-040-932882.indb 17 6/29/2017 10:33:40 AM

18

Manual del Propietario

Sistemas UPS

SmartOnline

®

en Rack/Torre 100% en Línea

No conveniente para los usos móviles.

1. Instrucciones de 19

Seguridad Importantes

2. Instalación 20

2.1 Instalación (Rack) 20

2.2 Instalación (Torre) 21

2.3 Conexión y Arranque 21

2.4 Conexiones Opcionales 22

3. Operación 25

3.1 Interruptores del 25

Panel Frontal

3.2 Ajustes Operacionales 25

Avanzados

3.3 Luces Indicadoras del 26

Panel Frontal

3.4 Panel Posterior 28

3.5 Comunicaciones 29

4. Solución de Problemas 30

5. Reemplazo de Baterías 31

6. Almacenamiento y 33

Reparaciones

6.1 Almacenamiento 33

6.2 Reparaciones 33

7. Cumplimiento de las Normas 34

English 1

Français 35

Русский

52

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

17-06-040-932882.indb 18 6/29/2017 10:34:35 AM

19

1.

Instrucciones de Seguridad Importantes

Advertencias sobre la Ubicación del UPS

• Instale el sistema UPS en interior, alejado de humedad o calor excesivos, contaminantes

conductores, polvo o luz solar directa.

• Para lograr el mejor rendimiento, mantenga la temperatura interior entre 0º C y 40º C (32º F

y 104º F).

• Deje un espacio adecuado alrededor de todos los costados del sistema UPS para que haya

una ventilación adecuada.

• No monte esta unidad con el panel frontal o con el panel trasero hacia abajo (Bajo ningún

ángulo o inclinación). Si lo monta de esta manera, inhibirá seriamente el sistema de

enfriamiento interno de la unidad; lo que finalmente causará daños al producto que no están

cubiertos por la garantía.

Advertencias para la Conexión del UPS

• Conecte el sistema UPS directamente a un tomacorriente de CA conectado a tierra

adecuadamente. El tomacorriente debe instalarse cerca del sistema UPS y tiene que tener un

fácil acceso para poder desconectarlo.

• A fin de reducir el riesgo de incendio, conecte solo a un circuito proporcionado con una

protección contra sobrecorriente con circuito de bifurcación de un máximo de 20 amperes de

acuerdo con su local y NEC (Código Eléctrico Nacional), ANSI/NFPA 70.

• No modifique la clavija del sistema UPS y tampoco use un adaptador que elimine la conexión

a tierra de la unidad. No enchufe el UPS en sí mismo, ya que esto lo dañará.

• No use cables de extensión para enchufar el sistema UPS a una salida CA.

• Si el sistema UPS recibe energía de un generador de CA alimentado por motor, el generador

debe proporcionar una salida de grado de computadora limpia y filtrada.

Advertencias acerca de la Conexión del Equipo

• El uso de este equipo en aplicaciones de soporte de vida en donde la falla de este equipo

pueda razonablemente hacer suponer que causará fallas en el equipo de soporte de vida o

afecte significativamente su seguridad o efectividad, no está recomendado.

• No conecte los supresores de sobretensiones o cables de extensión a la salida del sistema

UPS. Esto puede dañar el UPS y afectar las garantías del supresor de sobretensiones y del

UPS. La conexión de una unidad de distribución de energía (PDU) Tripp Lite a la salida del

sistema UPS es segura y no anulará la garantía.

Advertencias sobre la Batería

• Consulte la Sección 5: Reemplazo de Baterías para obtener una lista completa de

advertencias sobre la batería.

GUARDE ESTAS INSTRUCCIONES

Este manual contiene instrucciones y advertencias que deben seguirse durante la

instalación, operación y almacenamiento de este producto. La falta de observar

estas advertencias podría afectar su garantía.

17-06-040-932882.indb 19 6/29/2017 10:34:35 AM

20

2. Instalación

1

2

3

D

E

4

F

C

B

C

B

A

B

A

2.1 Instalación (Rack)

• Use los estantes para rackmount y lo accesorios de instalación incluidos para instalar el

sistema UPS en un rack o estante de 4 postes. Para instalar el sistema UPS en un rack de 2

postes (telecomunicaciones), pida el juego para rackmount en 2 postes de

Tripp Lite (modelo 2POSTRMKITWM, se vende por separado).

• Las instrucciones de este manual son para tipos de racks y estantes comunes y puede que

no sean adecuadas para todas las aplicaciones de montaje. El usuario debe determinar la

idoneidad de los accesorios y los procedimientos antes de la instalación. Si los accesorios o

procedimientos no son apropiados para la aplicación, póngase en contacto con el fabricante

del rack o gabinete para obtener una solución.

Advertencia: El sistema UPS es muy pesado, así que tenga cuidado cuando lo

mueve o lo levanta.

Procedimiento de Instalación en 4 Postes

1

Los ganchos plásticos

A

incluidos soportarán los

estantes

B

para rackmount vacíos hasta que se

instalen los accesorios de instalación

permanentes. Inserte un gancho cerca del centro

del soporte frontal y posterior de cada estante

como se muestra. (Cada soporte frontal tiene

seis orificios y cada soporte posterior posee tres

orificios.) Los ganchos encajarán en su lugar.

Después de colocar los ganchos, expanda cada

estante para que se ajuste con la profundidad de

los rieles del rack vertical. Los ganchos encajarán

en los orificios cuadrados en los rieles del rack

para sostener los estantes. Confirme que los

estantes estén nivelados en todas las direcciones.

Nota: El reborde de soporte de cada estante debe

quedar mirando hacia adentro.

2

Asegure de manera permanente los estantes

B

a los rieles del rack usando los tornillos más

largos que vienen incluidos y las arandelas

C

como se muestra. (Coloque quatro tornillos en

la parte frontal y quatro tornillos en la parte

posterior.) Apriete todos los tornillos antes de

continuar.

Advertencia: No intente instalar el

sistema UPS hasta que se hayan

insertado y apretado los tornillos

necesarios. Los ganchos plásticos no

soportarán el peso del UPS.

3

Una los soportes de montaje

D

a los orificios

de montaje hacia delante del sistema UPS

usando los tornillos más cortos

E

que vienen

incluidos. Las orejas del soporte de montaje

deben mirar hacia adelante.

4

Con la ayuda de un asistente, levante el sistema UPS y deslícelo dentro de los estantes de

montaje. Inserte quatro de los tornillos

F

incluidos a través de las orejas del soporte de

montaje y en los rieles del rack vertical. Apriete todos los tornillos de manera segura.

17-06-040-932882.indb 20 6/29/2017 10:34:36 AM

La page charge ...

Tripp Lite SmartOnline SUINT3000RTXL2U Le manuel du propriétaire

Ce manuel convient également à

Tripp Lite SmartOnline SUINT3000RTXL2U Le manuel du propriétaire

dans d''autres langues

Documents connexes