GYS 3154020024182 Le manuel du propriétaire

DBT400 START & STOP

BATTERY & ELETRICAL SYSTEM ANALYSER

TEST PROCEDURES / OPERATING INSTRUCTIONS

IMPORTANT

：

1. For testing 6 / 12 volt batteries and 12 / 24 volt charging

systems. (ONLY 12 volt for START & STOP battery test)

2. Suggested operation range 32℉(0℃) to 122℉(50℃) in

ambient temperature.

1 : Display

2 : Previous/Next keys

3 :ENTER key

1

3

2

EN - 1

WARNING：

1. Working in the vicinity of a lead acid battery is dangerous.

Batteries generate explosive gases during normal battery

operation. For this reason, it is of utmost importance, if

you have any doubt, that each time before using your

tester, you read these instructions very carefully.

2. To reduce risk of battery explosion, follow these

instructions and those published by the battery

manufacturer and manufacturer of any equipment you

intend to use in the vicinity of the battery. Observe

cautionary markings on these items.

3. Do not expose the tester to rain or snow.

PERSONAL SAFETY PRECAUTIONS：

1. Someone should be within range of your voice or close

enough to come to your aid when you work near a lead

acid battery.

2. Have plenty of fresh water and soap nearby in case

battery acid contacts skin, clothing or eyes.

3. Wear safety glasses and protective clothing.

4. If battery acid contacts skin or clothing, wash

immediately with soap and water. If acid enters eye,

immediately flood eye with running cold water for at least

ten minutes and get medical attention immediately.

5. NEVER smoke or allow a spark or flame in vicinity of

battery or engine.

6. Be extra cautious to reduce risk of dropping a metal tool

onto the battery. It could spark or short-circuit the battery

or other electrical parts and could cause an explosion.

7. Remove personal metal items such as rings, bracelets,

necklaces and watches when working with a lead acid

EN - 2

battery. It can produce a short circuit current high enough

to weld a ring or the like to metal causing a severe burn.

INSERTION OR REPLACEMRNT OF LEAD WIRE：

1. Remove the cover in the backside bottom of the battery

tester.

2. Insert the connectors which contain black-yellow pair and

yellow-red pair in one end of the lead wire into the

sockets which can be found when you remove the cover

as above. Be sure to make colors matched between the

connectors and sockets as shown below.

Red (Connector) Yellow

Red Yellow (Socket)

White

Connect Black

Black white

(RT003 Backside)

PREPARING TO TEST：

1. Be sure area around battery is well ventilated while

battery is being tested.

2. Clean battery terminals. Be careful to keep corrosion

from coming in contact with eyes.

3. Inspect the battery for cracked or broken case or cover. If

battery is damaged, do not use tester.

4. If the battery is not sealed maintenance free, add distilled

water in each cell until battery acid reaches level

specified by the manufacturer. This helps purge

excessive gas from cells. Do not overfill.

EN - 3

5. If necessary to remove battery from vehicle to test,

always remove ground terminal from battery first. Make

sure all accessories in the vehicle are off to ensure you

do not cause any arcing.

OPERATION & USE ：

1. Before you test a battery in a vehicle, turn off the ignition,

all accessories and loads. Close all the vehicle doors

and the trunk lid.

2. Make sure you have put 6pcs

of 1.5V battery into the battery

chamber. If the internal battery

runs out of power, screen will show “POWER LOW”.

Replace the batteries before starting the test.

Note that nothing will be seen on the display until

the tester is connected to a vehicle battery.

3. Make sure the battery terminals are clean. Wire brush

them if necessary. Clamp the black load lead to the

vehicle negative battery terminal. Clamp the red load

lead to the vehicle positive battery terminal. Please

clamp on the lead part of the terminal only. Clamping on

the iron part of the terminal will lead to wrong test

results.

POWER LOW

EN - 4

4. You will view the following screens：

SYSTEM ANALYZER

BATTERY VOLT

××.×× V

PRESS ＜ENTER＞

* Press <Enter> to select

function.

1.

BATTERY TEST

2.

SYSTEM TEST

3.

LANGUAGE

* Press▲\▼ to item 3 to select

language.

* Press <Enter> to set the

selection.

LANGUAGE

ENGLISH

* Press  to select language

(English, Dutch, Japanese,

Portuguese, Italian, Spanish,

German, & French.)

* Press <Enter> to confirm

choice & go back to battery

test.

EN - 5

1. Press the ▲\▼ key to select START STOP.

START STOP

BATTERY TEST

SYSTEM TEST

1. START STOP

2. Pr

ess the  key to select battery type :

a. EFB (ENHANCED FLOODED)

b. AGM

Press «ENTER» to confirm choice

3. Press the  key to select battery

rating:

SAE, CA, EN, IEC or DIN.

Press «ENTER» to confirm choice.

4. Press the  key to input

the battery capacity:

SAE (CCA) : 40~2,000

EN : 40~2,100

DIN : 25~1,300

IEC : 30~1,500

CA(MCA) :50~2,500

Press «ENTER» to begin test.

5. Press the  key to confirm the position of the battery

if the charge is detected. Follow the tester’s steps to

remove the surface charge if it happens..

6. Testing battery.

START-STOP BATTERY TEST

BATTERY TYPE

EFB

SELECT RATING

SAE

SET CAPACITY

XXXX SAE

TESTING

EN - 6

7. When the test is completed, the display shows the

actual volts and the actual CCA or %.

One of six results will be displayed:

GOOD & PASS:

The battery is good & capable

of holding a charge.

Press the▲\▼ key to show:

SOH (STATE OF HEALTH) &

SOC (STATE OF CHARGE).

GOOD & RECHARGE:

The battery is good but needs

to be recharged.

Press the▲\▼ key to show:

SOH (STATE OF HEALTH) &

SOC (STATE OF CHARGE).

RECHARGE & RETEST:

Battery is discharged. The

battery condition cannot be

determined until it is fully

charged. Recharge & retest

the battery.

Press the▲\▼ key to show:

SOH (STATE OF HEALTH) &

SOC (STATE OF CHARGE).

GOOD & PASS

↵

××.××V ×××× SAE

SOH: ×××× SAE

 XX%

SOH: ×××× SAE

↵

 XX%

SOC: ××.×× V

 XX%

GOOD & RECHARGE

××.××V ×××× SAE

SOH: ×××× SAE

 XX%

SOH: ×××× SAE

↵

 XX%

SOC: ××.×× V

 XX%

RECHARGE & RETEST

××.××V ×××× SAE

SOH: ×××× SAE

 XX%

SOH: ×××× SAE

↵

 XX%

SOC: ××.×× V

 XX%

EN - 7

BAD & REPLACE:

The battery will not hold a

charge. It should be

replaced immediately.

Press the▲\▼ key to show:

SOH (STATE OF HEALTH)

& SOC (STATE OF

CHARGE).

BAD CELL & REPLACE:

The battery has at least

one cell short circuit. It

should be replaced

immediately.

Press the▲\▼ key to show:

SOH (STATE OF HEALTH)

& SOC (STATE OF

CHARGE).

LOAD ERROR:

The tested battery is bigger

than 2000CCA or 200AH.

Or the clamps are not

connected properly.

Please fully charge the battery and retest after

excluding both previous reasons. If reading is the

same, the battery should be replaced immediately.

8. Press <ENTER> return to the manual or remove the

test clamps from the battery posts after completion of

testing batteries to end test.

BAD & REPLACE

↵

××.××V ×××× SAE

SOH: ×××× SAE

 XX%

SOH: ×××× SAE

↵

 XX%

SOC: ××.×× V

 XX%

BAD CELL & REPLACE

××.××V ×××× SAE

SOH: ×××× SAE

 XX%

SOH: ×××× SAE

↵

 XX%

SOC: ××.×× V

 XX%

LOAD ERROR

EN - 8

SET CAPACITY

1. Press ▼/▲key to

select Item 1. BATTERY TEST

Press <ENTER> button.

2.

Example :

Press the / key to select

the BATTERY TYPE：

a. REGULAR LIQUID

b. AGM FLAT PLATE

c. AGM SPIRAL

d. VRLA/GEL

3. Press ▼/▲ key to

SELECT RATING

4. Press the

 key to

select the battery rating： SAE, EN, JIS, CA, DIN or

IEC.

5. Press ▼/▲ key to

6. Press the  key to input the

battery capacity of CCA：

• SAE：40~2000

• EN：40~2100

• JIS：By Battery Type Number

• CA：50~2500

• DIN：25~1300

• IEC：30~1500

Press <ENTER> to begin the test.

7. Test the battery for few seconds.

BATTERY TEST

BATTERY TYPE

AGM FLAT

PLATE SELECT

RATING

SET CAPACITY

×××× SAE

PRESS <ENTER>

TO TEST

TESTING

EN - 9

GOOD & PASS

↵

××.××V ×××× SAE

SOH: ×××× SAE

 XX%

8. Press the  key to select

battery fully charged or not if

tester asks. Press <ENTER>

to confirm choice.

9. When the test is completed, the display shows the

actual volts and the actual CCA or %.

One of six results will be displayed:

GOOD & PASS :

The battery is good & capable

of holding a charge.

Press the▲\▼ key to show:

SOH (STATE OF HEALTH) &

SOC (STATE OF CHARGE).

GOOD & RECHARGE :

The battery is good but needs

to be recharged.

Press the▲\▼ key to show:

SOH (STATE OF HEALTH) &

SOC (STATE OF CHARGE).

RECHARGE & RETEST :

Battery is discharged. The

battery condition cannot be

determined until it is fully

charged. Recharge & retest

the battery.

Press the▲\▼ key to show:

BATTERY FULLY

↵

CHARGED? YES

SOH: ×××× SAE

↵

 XX%

SOC: ××.×× V

 XX%

GOOD & RECHARGE

××.××V ×××× SAE

SOH: ×××× SAE

 XX%

SOH: ×××× SAE

↵

 XX%

SOC: ××.×× V

 XX%

RECHARGE & RETEST

××.××V ×××× SAE

SOH: ×××× SAE

 XX%

SOH: ×××× SAE

↵

 XX%

SOC: ××.×× V

 XX%

EN - 10

SOH (STATE OF HEALTH) & SOC (STATE OF

CHARGE).

BAD & REPLACE :

The battery will not hold a

charge. It should be

replaced immediately.

Press the▲\▼ key to show:

SOH (STATE OF HEALTH)

& SOC (STATE OF

CHARGE).

BAD CELL & REPLACE :

The battery has at least

one cell short circuit. It

should be replaced

immediately.

Press the▲\▼ key to show:

SOH (STATE OF HEALTH)

& SOC (STATE OF

CHARGE).

LOAD ERROR :

The tested battery is bigger

than 2000CCA or 200AH.

Or the clamps are not

connected properly.

Please fully charge the battery and retest after

excluding both previous reasons. If reading is the

same, the battery should be replaced

immediately.

BAD & REPLACE

↵

××.××V ×××× SAE

SOH: ×××× SAE

 XX%

SOH: ×××× SAE

↵

 XX%

SOC: ××.×× V

 XX%

BAD CELL & REPLACE

××.××V ×××× SAE

SOH: ×××× SAE

 XX%

SOH: ×××× SAE

↵

 XX%

SOC: ××.×× V

 XX%

LOAD ERROR

EN - 11

10. Press <ENTER> return to the manual or remove the

test clamps from the battery posts after completion of

testing batteries to end test.

Example :

1. Press ▼/▲key to select Item

2. SYSTEM TEST

Press <ENTER> button.

2. Turn off all vehicle accessory

loads such as light, air

conditioning, radio, etc. before

starting the engine.

3. When the engine is started, one of the three results will

be displayed along with the actual reading measured.

CRANKING VOLTS NORMAL

The system is showing normal

draw. Press <ENTER> to

perform the charging system

test.

CRANKING VOLTS LOW

The cranking voltage is

below normal limits,

troubleshoot the starter

with manufacturers

recommended procedure.

CRANKING VOLTS NO DETECTED

The cranking voltage is not

detected.

4. If the cranking voltage is

normal, press <ENTER> to

begin charging system test.

SYSTEM TEST

1. BATTERY TEST

↵

.

2. SYSTEM TEST

3. LANGUAGE

TURN OFF LOADS

START ENGINE

CRANKING VOLTS

↵

××.××V NORMAL

CRANKING VOLTS

××.××V LOW

CRANKING VOLTS

NO DETECTED

PRESS ENTER FOR

CHARGING TEST

MAKE SURE ALL

↵

LOADS ARE OFF

EN - 12

5. Press <ENTER> key, you will view the following screen.

6. Press <ENTER> key, one of the three results will be

displayed along with the actual reading measured.

LOW CHARGING VOLTS WHEN TEST AT IDLE

The alternator is not providing

sufficient current to the battery.

Check the belts to ensure the

alternator is rotating with

engine running. If the belts are slipping or broken,

replace the belts and retest. Check the connections

from the alternator to the battery. If the connection is

loose or heavily corroded, clean or replace the cable

and retest. If the belts and connections are in good

condition, replace the alternator.

CHARGING SYSTEM NORMAL WHEN TEST AT IDLE

The system is showing normal

output from the alternator. No

problem is detected.

HIGH CHARGING VOLTS WHEN TEST AT IDLE

The voltage output from the

alternator to the battery

exceeds the normal limits of a

functioning regulator. Check to

ensure there is no loose connection and the ground

connection is normal. If there is no connection issue,

replace the regulator. Since most alternators have the

regulator built-in, this will require you to replace the

alternator. The normal high limit of a typical automotive

regulator is 14.7 volts +/- 0.05. Check manufacturer

specifications for the correct limit, as it will vary by

vehicle type and manufacturer.

ALT. IDLE VOLTS

↵

××.××V LOW

ALT. IDLE VOLTS

↵

××.××V NORMAL

ALT. IDLE VOLTS

↵

××.××V HIGH

EN - 13

7. Following the charging system

at idle, press <ENTER> for the

charging system with

accessory loads. Turn on the

blower to high (heat), highbeam headlights, and rear

defogger. Do not use cyclical loads such as air

conditioning or windshield wipers.

8. When testing older model

diesel engines, the users need

to run up the engine to 2500

rpm for 15 seconds. You will

view the screen as follows:

9. Press <ENTER> to look for the amount of ripple from

the charging system to the battery. One of two testing

results will be displayed along with the actual testing

measured.

RIPPLE DETECTED NORMAL

Diodes function well in the alternator / stator.

Or

EXCESS RIPPLE DETECTED

One or more diodes in the

alternator are not functioning

or there is stator damage.

Check to ensure the alternator

mounting is sturdy and that the belts are in good shape

and functioning properly. If the mounting and belts are

good, replace the alternator.

10. Press <ENTER> key to continue the charging system

with accessory loads. One of the three results will be

displayed along with the actual testing measured.

TURN ON LOADS

AND PRESS ENTER

RUN ENGINE UP TO

2500 RPM 15 SEC.

RIPPLE DETECTED

××.××V NORMAL

NO RIPPLE DETECT

AND PRESS ENTER

RIPPLE DETECTED

××.××V HIGH

EN - 14

ALT. LOAD VOLTS

↵

××.××V NORMAL

CHARGING SYSTEM HIGH WHEN TEST WITH

ACCESSORY LOADS

The voltage output from the

alternator to the battery

exceeds the normal limits of a

functioning regulator. Check to

ensure there are no loose

connections and that the ground connection is normal.

If there are no connection issues, replace the regulator.

Since most alternators have the regulator built-in, this

will require you to replace the alternator.

CHARGING SYSTEM LOW WHEN TEST WITH

ACCESSORY LOADS

The alternator is not providing

sufficient current for the

system’s electrical loads and

the charging current for the battery. Check the belts to

ensure the alternator is rotating with the engine running.

If the belts are slipping or broken, replace the belts and

retest. Check the connections from the alternator to the

battery. If the connection is loose or heavily corroded,

clean or replace the cable and retest. If the belts and

connections are in good working condition, replace the

alternator.

CHARGING SYSTEM NORMAL WHEN TEST WITH

ACCESSORY LOADS

The system is showing normal

output from the alternator. No

problem detected.

11. Press <ENTER> key when

charging system test is

completed finish. Turn all

accessory loads and engine

ALT. LOAD VOLTS

↵

××.××V HIGH

ALT. LOAD VOLTS

↵

××.××V LOW

TEST OVER. TURN

OFF LOADS & ENGINE

EN - 15

off. Press <ENTER> key to return to the manual or

remove the test clamps from the battery posts after

completion of testing to end test.

GLOSSARY

What is GEL battery?

Gel battery is a lead-acid electric storage battery that:

 is sealed using special pressure valves and should never

be opened.

 is completely maintenance-free.*

 uses thixotropic gelled electrolyte.

 uses a recombination reaction to prevent the escape of

hydrogen and oxygen gases normally lost in a flooded

lead-acid battery (particularly in deep cycle applications).

 is non-spillable, and therefore can be operated in virtually

any position. However, upside-down installation is not

recommend-ed.

Connections must be retorqued and the batteries should

be cleaned periodically.

What is AGM battery?

AGM battery is a lead-acid electric storage battery that:

 is sealed using special pressure valves and should never

be opened.

 is completely maintenance-free.*

 has all of its electrolyte absorbed in separators consisting

of a sponge-like mass of matted glass fibers.

 uses a recombination reaction to prevent the escape of

hydrogen and oxygen gases normally lost in a flooded

lead-acid battery (particularly in deep cycle applications).

 is non-spillable, and therefore can be operated in virtually

any position. However, upside-down installation is not

recommended.

 Connections must be retorqued and the batteries should

be cleaned periodically.

EN - 16

What is REGULAR LIQUID battery?

These initials stand for Starting, Lighting and Ignition, which

are the three basic functions which a battery has to perform

on all normal vehicles. Batteries given this description will

have been specifically designed for service on cars and trucks

within a voltage controlled electrical system. Those

REGULAR LIQUID batteries which are intended for heavy

haulage vehicles fitted with large diesel motors may often be

called COMMERCIAL batteries. They have to be much more

powerful and more robust than batteries intended for cars.

What is STATE OF HEALTH?

It means how much battery capacity is left (%) comparing with

the marked original battery capacity.

What is STATE OF CHARGE?

It means how many percent of the battery is actually charged.

What is CCA (COLD CRANKING AMPS)?

The current in amperes which a new fully charged battery can

deliver for 30 seconds continuously without the terminal

voltage falling below 1.2volts per cell, after it has been cooled

to 0

O

F and held at that temperature. This rating reflects the

ability of the battery to deliver engine starting currents under

winter conditions.

What is AMPERE-HOUR?

The unit of measurement of electrical capacity. A current of

one ampere for one hour implies the delivery or receipt of one

ampere-hour of electricity. Current multiplied by time in hours

equals ampere-hours.

EN - 17

TERMS AND CONDITIONS OF WARRANTY

Any battery tester defective in material or workmanship will

be repaired or replaced according to published defective

return test repair procedures. The existence of a defect shall

be determined by the seller in accordance with published

procedures. The published test procedures are available

upon request.

This

warranty does not cover any unit that has been

damaged due to accident, abuse, alternation, use for a

purpose other than that for which it was intended, or failure to

follow operating instructions. This warranty is expressly

limited to original retail buyers. This warranty is not

assignable or transferable. Proof of purchase is required for

all alleged claims. Warranty cannot be authorized without

proof of purchase. Warranty claims must be sent pre-paid

with dated proof of purchase. Damage incurred during

shipment is the responsibility of the shipper (customer

returning unit) If the returned unit qualifies for warranty, the

shipper will only incur shipping cost. The seller reserves the

right to substitute or offer alternative warranty options at its

discretion.

The sole and exclusive remedy for any unit found to be

defective is repair or replacement, at the option of the seller.

In no event shall the seller be liable for any direct, indirect,

special, incidental, or consequential damages (including lost

profit) whether based on warranty, contract, tort, or any other

legal theory.

RETURN GOODS:

Pack with sufficient over-pack to prevent damage during

shipment. Damage incurred during return shipment is not

covered under this warranty. Repair costs for such

damages will be charged back to shipper.

REMARK:

WHEN RETURNING GOODS, PLEASE SHOW “RETURN

GOODS” ON ALL INVOICES & RELATED

SHIPPING DOCUMENTS TO PREVENT ANY EXTRA

CHARGE.”

EN - 18

DBT400 TESTEUR DE BATTERIE START & STOP

MESURES DE SÉCURITÉ

IMPORTANT

1. Test les batteries de 6 et 12 volts et test du système de

charge de 12 et 24 volt. (SEULEMENT 12 volt pour les

batteries de START

& STOP )

2. I

a

nt

m

e

bi

rv

a

nt

lle

e d

de

e 0

fon

℃

c

t

(

i

3

o

2

nn

℉

e

)

m

à

e

5

n

0

t c

℃

o

(

ns

12

ei

2

ll

℉

é :

).

t

empérature

1 : Ecran

2 : Bouton suivant/précédent

3 : Bouton ENTER

1

3

2

FR - 19

AVERTISSEMENT

1. Il est dangereux de travailler près d'une batterie au plomb-

acide. Lors du fonctionnement normal d'une batterie, des

gaz explosifs sont émis. Pour cette raison il est primordial

de lire et de suivre les instructions, chaque fois que vous

utilisez votre testeur.

2. Afin de réduire les risques d'explosion de la batterie, vous

devez suivre ces instructions ainsi que celles du fabricant

de la batterie ou du fabricant de tout équipement utilisé

près de la batterie. Lisez les avertissements apposés sur

ces produits.

3. Ne pas exposer le testeur à la pluie ou a la neige.

4. N'utilisez pas le testeur si les câbles sont endommagés,

remplacez-les immédiatement.

5. N'utilisez pas le testeur s'il est endommagé de quelque

façon que ce soit, faites-le réparer par un technicien

spécialisé.

PRÉCAUTIONS DE SÉCURITÉ

1. Assurez-vous qu'il y a quelqu'un à porter de vois ou

suffisamment près pour venir à votre aide lorsque vous

travaillez près d'une batterie au plomb-acide.

2. Assurez-vous d'avoir une bonne quantité d'eau fraîche et

du savon à proximité, au cas ou votre peau, vos yeux ou

vos vêtements entreraient en contact avec l'acide de la

batterie.

3. Portez des verres de sécurité et des vêtements appropriés.

Évitez de toucher à vos yeux lorsque vous travaillez près

d'une batterie.

4. Si l'acide de la batterie entre en contact avec votre peau ou

vos vêtements, lavez-les immédiatement avec de l'eau et

du savon. Si l'acide pénètre dans vos yeux, aspergez-les

FR - 20

La page charge ...

GYS 3154020024182 Le manuel du propriétaire

Ce manuel convient également à

GYS 3154020024182 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents