Jenn-Air 42 inch Manuel utilisateur

Marque: Jenn-Air

Modèle: 42 inch

Catégorie: Hottes

Taper: Manuel utilisateur

Ce manuel convient également à

JENN-AIR

36" AND 42" (91.4 CM AND 106.7 CM) ISLAND

CANOPY RANGE HOOD

HOTTE DE CUISINIÈRE JENN-AIR

POUR ÎLOT DE

36" ET 42" (91,4 CM ET 106,7 CM)

Installation Instructions and Use & Care Guide

For questions about features, operation/performance, parts, accessories, or service in the U.S.A., call:

1-800-JENNAIR (1-800-536-6247) or visit our website at www.jennair.com.

In Canada, call: 1-800-JENNAIR (1-800-536-6247), or visit our website at www.jennair.ca.

Instructions d’installation et Guide d’utilisation et d’entretien

Au Canada, pour assistance, installation ou service, composez le 1-800-JENNAIR (1-800-536-6247) ou visitez notre site web à

www.jennair.ca.

Table of Contents/Table des matières.............2

IMPORTANT: READ AND SAVE THESE INSTRUCTIONS.

FOR RESIDENTIAL USE ONLY.

IMPORTANT : LIRE ET CONSERVER CES INSTRUCTIONS.

POUR UTILISATION RÉSIDENTIELLE UNIQUEMENT.

LI3W7D/W10274319H

TABLE OF CONTENTS

RANGE HOOD SAFETY .................................................................2

INSTALLATION REQUIREMENTS ................................................4

Tools and Parts ............................................................................4

Location Requirements................................................................4

Venting Requirements..................................................................5

Electrical Requirements ...............................................................6

INSTALLATION INSTRUCTIONS ..................................................7

Prepare Location..........................................................................7

Assemble and Install Range Hood ..............................................7

Make Electrical Connection .........................................................9

Install Duct Covers.....................................................................10

Complete Installation .................................................................11

RANGE HOOD USE......................................................................12

Display........................................................................................12

Light............................................................................................12

Timer...........................................................................................12

Fan Speed Buttons ....................................................................13

RANGE HOOD CARE ...................................................................13

Cleaning......................................................................................13

WIRING DIAGRAM ......................................................................14

ASSISTANCE OR SERVICE.........................................................15

In the U.S.A. ...............................................................................15

Accessories................................................................................15

In Canada ...................................................................................15

WARRANTY .................................................................................16

TABLE DES MATIÈRES

SÉCURITÉ DE LA HOTTE DE CUISINIÈRE................................17

EXIGENCES D'INSTALLATION...................................................19

Outils et pièces...........................................................................19

Exigences d'emplacement.........................................................19

Exigences concernant l'évacuation ...........................................20

Spécifications électriques ..........................................................21

INSTRUCTIONS D’INSTALLATION.............................................22

Préparation de l’emplacement...................................................22

Assemblage et installation de la hotte .......................................22

Raccordement électrique...........................................................24

Installation des cache-conduits .................................................25

Achever l'installation ..................................................................26

UTILISATION DE LA HOTTE .......................................................27

Affichage.....................................................................................27

Éclairage.....................................................................................27

Minuterie.....................................................................................28

Boutons de vitesse du ventilateur..............................................28

ENTRETIEN DE LA HOTTE..........................................................29

Nettoyage ...................................................................................29

SCHÉMA DE CÂBLAGE ..............................................................30

ASSISTANCE OU SERVICE.........................................................31

Au Canada..................................................................................31

Accessoires ................................................................................31

GARANTIE ....................................................................................32

RANGE HOOD SAFETY

You can be killed or seriously injured if you don't immediately

You

can be killed or seriously injured if you don't

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

State of California Proposition 65 Warnings:

WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other

reproductive harm.

IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK, OR INJURY TO PERSONS, OBSERVE THE

FOLLOWING:

■ Use this unit only in the manner intended by the

manufacturer. If you have questions, contact the

manufacturer.

■ Before servicing or cleaning the unit, switch power off at

service panel and lock the service disconnecting means to

prevent power from being switched on accidentally. When

the service disconnecting means cannot be locked,

securely fasten a prominent warning device, such as a tag,

to the service panel.

■ Installation work and electrical wiring must be done by

qualified person(s) in accordance with all applicable codes

and standards, including fire-rated construction.

■ Do not operate any fan with a damaged cord or plug.

Discard fan or return to an authorized service facility for

examination and/or repair.

■ Sufficient air is needed for proper combustion and

exhausting of gases through the flue (chimney) of fuel

burning equipment to prevent backdrafting. Follow the

heating equipment manufacturer's guideline and safety

standards such as those published by the National Fire

Protection Association (NFPA), the American Society for

Heating, Refrigeration and Air Conditioning Engineers

(ASHRAE), and the local code authorities.

■ When cutting or drilling into wall or ceiling; do not damage

electrical wiring and other utilities.

■ Ducted fans must always be vented outdoors.

CAUTION: For general ventilating use only. Do not use

to exhaust hazardous or explosive materials and vapors.

CAUTION: To reduce risk of fire and to properly exhaust

air, be sure to duct air outside - do not vent exhaust air into

spaces within walls or ceilings, attics or into crawl spaces,

or garages.

WARNING: TO REDUCE THE RISK OF FIRE, USE ONLY

METAL DUCTWORK.

WARNING: TO REDUCE THE RISK OF A RANGE TOP

GREASE FIRE:

■ Never leave surface units unattended at high settings.

Boilovers cause smoking and greasy spillovers that may

ignite. Heat oils slowly on low or medium settings.

■ Always turn hood ON when cooking at high heat or when

flambeing food (i.e. Crepes Suzette, Cherries Jubilee,

Peppercorn Beef Flambé).

■ Clean ventilating fans frequently. Grease should not be

allowed to accumulate on fan or filter.

■ Use proper pan size. Always use cookware appropriate for

the size of the surface element.

WARNING: TO REDUCE THE RISK OF INJURY TO

PERSONS IN THE EVENT OF A RANGE TOP GREASE

FIRE, OBSERVE THE FOLLOWING:

■ SMOTHER FLAMES with a close fitting lid, cookie sheet, or

metal tray, then turn off the burner. BE CAREFUL TO

PREVENT BURNS. If the flames do not go out

immediately, EVACUATE AND CALL THE FIRE

DEPARTMENT.

■ NEVER PICK UP A FLAMING PAN - you may be burned.

■ DO NOT USE WATER, including wet dishcloths or towels -

a violent steam explosion will result.

■ Use an extinguisher ONLY if:

– You know you have a class ABC extinguisher, and you

already know how to operate it.

– The fire is small and contained in the area where it

started.

– The fire department is being called.

– You can fight the fire with your back to an exit.

Based on "Kitchen Fire Safety Tips" published by NFPA.

■ WARNING: To reduce the risk of fire or electrical shock,

do not use this fan with any solid-state speed control

device.

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed here.

Tools needed

■ Level

■ Drill with 1¼" (3.0 cm), ³⁄₈" (9.5 mm), ⁷⁄₆₄" (2.75 mm) and ¹⁄₈"

(3.0 mm) drill bits

■ Pilot hole drill bits (determined by chimney support

attachment method)

■ Pencil

■ Wire stripper or utility knife

■ Tape measure or ruler

■ Pliers

■ Caulking gun and weatherproof caulking compound

■ Vent clamps

■ Jigsaw or keyhole saw

■ Flat-blade screwdriver

■ Metal snips

■ Phillips screwdriver

Parts needed

■ Home power supply cable

■ 2 - ½" (12.7 mm) UL listed or CSA approved strain reliefs

■ 3 UL listed wire connectors

For vented installations, you will also need:

■ 1 wall or roof cap

■ Metal vent system

For non-vented (recirculating) installations, you will also need:

■ Charcoal Filter Kit Part Number W10272068 for non-vented

(recirculating) installations only. See “Assistance or Service”

section to order.

■ Recirculating Kit Part Number W10272061 for non-vented

(recirculating) installations only. See “Assistance or Service”

section to order.

■ 8" (20.3 cm) round metal vent duct. Length required is

determined by ceiling height.

Parts Supplied

Remove parts from packages. Check that all parts are included.

■

Hood canopy assembly with ventilator and light bulbs installed

■ Filter—installed in hood canopy

■ 64 - 4.2 x 8 mm screws

■ 4 - 5 x 45 mm screws

■ Mounting template

■ 2 - Upper vent covers

■ 2 - Lower vent covers

■ Vent transition with backdraft damper installed

■ 4 - Plastic vent clips

■ Upper horizontal support bracket

■ Horizontal support

■ 8 - Vertical supports

■ 4 - 3.5 x 6.5 mm screws

■ 2 - 2.9 x 3 mm screws

■ T10 Torx

®†

adapter

■ T20

Torx

adapter

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.

Have a qualified technician install the range hood. It is the

installer's responsibility to comply with installation clearances

specified on the model/serial rating plate. The model/serial rating

plate is located behind the left filter on the rear wall of the vent

hood.

Canopy hood location should be away from strong draft areas,

such as windows, doors and strong heating vents.

Cabinet opening dimensions that are shown must be used. Given

dimensions provide minimum clearance.

Grounded electrical outlet is required. See “Electrical

Requirements” section.

Because of the size and weight of this island hood, the chimney

support must be securely attached to the ceiling.

■ For plaster or drywall ceilings, the chimney support must be

attached to joists. If this is not possible, you must build a

support structure behind the plaster or drywall. The support

structure must be able to support 80 lbs (36.6 kg).

This range hood is recommended for use with cooktops with a

maximum total rating of 60,000 Btus or less.

The range hood is factory set for venting through the roof.

For non-vented (recirculating) Installation see “Non-vented

(recirculating) Installations” in “Install Range Hood” section.

Recirculation Kit Part Number W10272061 is available from your

dealer or an authorized parts distributor.

All openings in ceiling and wall where range hood will be installed

must be sealed.

For Mobile Home Installations

The installation of this range hood must conform to the

Manufactured Home Construction Safety Standards, Title 24

CFR, Part 328 (formerly the Federal Standard for Mobile Home

Construction and Safety, Title 24, HUD, Part 280) or when such

standard is not applicable, the standard for Manufactured Home

Installation 1982 (Manufactured Home Sites, Communities and

Setups) ANSI A225.1/NFPA 501A, or latest edition, or with local

codes.

Product Dimensions

*Vented installations only

**Non-vented (recirculating) installations only

†®TORX and T20 are registered trademarks of Acument Intellectual Properties, LLC.

12¹⁄₄"

(31.0 cm)

13³⁄₁₆"

(33.5 cm)

36" (91.2 cm)

42" (106.4 cm)

*32¹⁄₂"

(82.6 cm)

min.

*46¹⁄₂"

(118.0 cm)

max.

**32¹⁄₂"

(82.6 cm)

min.

**52⁹⁄₁₆"

(133.5 cm)

max.

27" (68.6 cm)

Installation Dimensions

IMPORTANT:

Minimum distance “C”: 24" (61.0 cm) from electric cooking

surface.

Minimum distance “C”: 27" (68.6 cm) from gas cooking

surface.

Suggested maximum distance “C”: 36" (91.4 cm)

The chimneys can be adjusted for different ceiling heights. See

the following chart.

*NOTE: The range hood chimneys are adjustable and designed

to meet varying ceiling or soffit heights depending on the

distance “C” between the bottom of the range hood and the

cooking surface. For higher ceilings, a Stainless Steel Chimney

Extension Kit Part Number W10688278 is available from your

dealer or an authorized parts distributor. The chimney extension

replaces the upper chimney shipped with the range hood.

Venting Requirements

■ Vent system must terminate to the outside, except for non-

vented (recirculating) installations.

■ Do not terminate the vent system in an attic or other enclosed

area.

■ Do not use 4" (10.2 cm) laundry-type wall caps.

■ Use metal vent only. Rigid metal vent is recommended. Do

not use plastic or metal foil vent.

■ The vent system must have a damper. If the roof or wall cap

has a damper, do not use the damper supplied with the range

hood.

For the most efficient and quiet operation:

■ Use a straight run or as few elbows as possible.

■ Use no more than three 90° elbows.

■ Make sure there is a minimum of 24" (61.0 cm) of straight

vent between the elbows if more than 1 elbow is used.

■ Do not install 2 elbows together.

■ Use vent clamps to seal all joints in the vent system.

■ Use caulking to seal exterior wall or roof opening around the

cap.

■ The size of the vent should be uniform.

Cold Weather Installations

An additional back draft damper should be installed to minimize

backward cold air flow and a thermal break should be installed to

minimize conduction of outside temperatures as part of the vent

system. The damper should be on the cold air side of the thermal

break.

The break should be as close as possible to where the vent

system enters the heated portion of the house.

Makeup Air

Local building codes may require the use of makeup air systems

when using ventilation systems greater than specified CFM of air

movement. The specified CFM varies from locale to locale.

Consult your HVAC professional for specific requirements in your

area.

Venting Methods

This island hood is factory set for venting through the roof.

An 8" (20.3 cm) round vent system is needed for installation (not

included). The hood exhaust opening is 8" (20.3 cm) round.

NOTE: Flexible vent is not recommended. Flexible vent creates

back pressure and air turbulence that greatly reduce

performance.

Vent system can terminate either through the roof or wall. To vent

through a wall, a 90° elbow is needed.

For Non-Vented (recirculating) Installations

If it is not possible to vent cooking fumes and vapors to the

outside, the hood can be used in the non-vented (recirculating)

version, fitting a charcoal filter and the deflector. Fumes and

vapors are recycled through the top grille.

A. Ceiling height

B. Hood height from ceiling to bottom of the

range hood: A-C-D=B

C. 24" (61.0 cm) minimum to 36" (91.4 cm)

maximum suggested hood height.

D. Countertop height

Vented Installations

Min. ceiling height Max. ceiling height

Electric cooking

surface

7' 9" (2.36 m) 9' 10" (3.0 m)

Gas cooking

surface

8' (2.44 m) 9' 10" (3.0 m)

Non-Vented (Recirculating) Installations

Min. ceiling height Max. ceiling height

Electric cooking

surface

7' 9" (2.36 m) 10' 4" (3.15 m)

Gas cooking

surface

8' (2.44 m) 10' 4" (3.15 m)

C A

NOTE: Wall venting can be an option for 2-story homes.

Calculating Vent System Length

To calculate the length of the system you need, add the

equivalent feet (meters) for each vent piece used in the system.

Maximum equivalent vent length is 35 ft (10.7 m).

Example Vent System

The following example falls within the maximum vent length of

35 ft (10.7 m).

Electrical Requirements

Observe all governing codes and ordinances.

Ensure that the electrical installation is adequate and in

conformance with National Electrical Code, ANSI/NFPA 70 (latest

edition), or CSA Standards C22.1-94, Canadian Electrical Code,

Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes

and ordinances.

If codes permit and a separate ground wire is used, it is

recommended that a qualified electrician determine that the

ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

1 Batterymarch Park

Quincy, MA 02169-7471

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

■ A 120 volt, 60 Hz., AC only, 15-amp, fused electrical circuit is

required.

■ If the house has aluminum wiring, follow the procedure

below:

1. Connect a section of solid copper wire to the pigtail

leads.

2. Connect the aluminum wiring to the added section of

copper wire using special connectors and/or tools

designed and UL listed for joining copper to aluminum.

Follow the electrical connector manufacturer's recommended

procedure. Aluminum/copper connection must conform with

local codes and industry accepted wiring practices.

■ Wire sizes and connections must conform with the rating of

the appliance as specified on the model/serial rating plate.

The model/serial plate is located behind the filter on the rear

wall of the range hood.

■ Wire sizes must conform to the requirements of the National

Electrical Code, ANSI/NFPA 70 (latest edition), or CSA

Standards C22. 1-94, Canadian Electrical Code, Part 1 and

C22.2 No. 0-M91 (latest edition) and all local codes and

ordinances.

Roof venting Non-vented (recirculating)

A. Roof cap

B. 8" (20.3 cm) round vent

A. Deflector

B. 8" (20.3 cm) round vent

Vent piece 8" (20.3 cm) round

45° elbow

2.5 ft

(0.8 m)

90° elbow

5.0 ft

(1.5 m)

1 - 90° elbow = 5.0 ft (1.5 m)

1 - wall cap = 0.0 ft (0.0 m)

8 ft (2.4 m) straight = 8.0 ft (2.4 m)

System length = 13 ft (3.9 m)

90 elbow

6 ft (1.8 m)

2 ft

(0.6 m)

Wall cap

INSTALLATION INSTRUCTIONS

Prepare Location

■ It is recommended that the vent system be installed before

the range hood is installed.

■ Before making cutouts, make sure there is proper clearance

within the ceiling for exhaust vent.

■ Range hood is to be installed 24" (61.0 cm) min. for electric

cooking surfaces or 27" (68.6 cm) min. for gas cooking

surfaces to suggested maximum of 36" (91.2 cm) above the

cooking surface.

■ Check your ceiling height and the range hood height

maximum before you select your hood.

1. Disconnect power.

2. Determine which venting method to use: roof, or non-vented.

3. Select a flat surface for assembling the range hood. Place

covering over that surface.

4. Using 2 or more people, lift range hood onto covered surface.

Range Hood Mounting Screws Installation

1. Determine and mark the centerline on the ceiling where the

range hood will be installed, considering the requirements for

ceiling support structures. See the “Location Requirements”

section. Make sure the range hood is centered over the

cooking surface.

2. Tape template in place on the ceiling at the marked

centerline. The line for the front of the range hood should be

parallel to the front of the cooktop.

3. Use a pencil to mark the mounting screws, wire access and

duct hole locations on the ceiling.

NOTE: Mounting hole locations should be into a ceiling

support structure capable of holding 80 lbs (36.6 kg).

Remove the template.

4. Drill 4 - ³⁄₁₆" (4.8 mm) pilot holes for mounting the upper

horizontal support.

Complete Preparation

1. Determine the required location for the home power supply

cable and drill a ½" (1.3 cm) diameter hole for wire access.

2. Run wire through the home power supply cable according to

the National Electrical Code or CSA Standards and local

codes and ordinances. There must be enough ½" conduit

and wires from the fused disconnect (or circuit breaker) box

to make the connection in the hood’s electrical terminal box.

NOTE: Do not reconnect power until installation is complete.

3. For vented installations only: Using a jigsaw or keyhole

saw, cut a 8½" (21.6 cm) diameter hole for the vent duct.

Attach the upper horizontal support bracket with 4 - 5 x 45 mm

wood screws.

IMPORTANT: All screws must be installed into wood. If there

is no wood to screw into, additional wall framing supports

may be required.The ceiling support structure must be

capable of holding 80 lbs (36.6 kg).

Assemble and Install Range Hood

1. Install the vent transition on top of the hood (if removed for

shipping) with 4 - 4.2 x 8 mm sheet metal screws.

2. Position the 4 vertical supports (A) with notches at the bottom

and attach to the range hood using 16 - 4.2 x 8 mm screws.

WARNING

Excessive Weight Hazard

Use two or more people to move and install

range hood.

Failure to do so can result in back or other injury.

A. Upper horizontal support

A. Vent transition

B. 4.2 x 8 mm screws (4)

3. Attach the horizontal support (B) using 8 - 4.2 x 8 mm screws.

4. Attach a second set of vertical supports (A) and set the

vertical height (B). See “Installation Dimensions” in the

“Location Requirements” section to help determine the

desired dimension for the vertical height “B.”

Secure with 16 - 4.2 x 8 mm T20

screws.

5. Using 2 or more people, lift the range hood assembly and

attach it by snapping the vertical supports to the spring clips

in the upper horizontal support bracket that is mounted to the

ceiling.

NOTE: The range hood assembly must be held in place while

install the screws in the next step.

6. Install 16 - 4.2 x 8 mm screws and tighten to secure.

Connect Vent System

1. Install vent system.

2. Push duct over the exhaust outlet. Seal all connections with

vent clamps.

3. Use caulk to seal all openings.

Non-Vented (Recirculating) Installation

1. Attach the air deflector to the upper horizontal support using

mounting screws.

2. Measure the length of 8" (20.3 cm) duct needed to connect

the transition to the deflector.

NOTE: Vent should fit up inside the deflector 1" (2.5 cm)

minimum.

3. Install vent between the transition and the deflector.

NOTE: To make vent installation easier, temporarily remove

the deflector from the chimney support bracket and replace

after vent section is in place.

4. Seal all connections with vent clamps.

A. Vertical supports

B. Horizontal support

A. Vertical supports

B. Vertical height

A. Mounting screws

A. Deflector

B. Mounting screws

Make Electrical Connection

1. Disconnect power.

2. Remove terminal box cover.

3. Remove the knockout in the terminal box and install a UL

listed or CSA approved ¹⁄₂"

strain relief.

4. Run home power supply cable through strain relief, into

terminal box.

5. Use UL listed wire connectors and connect black wires (C)

together.

6. Use UL listed wire connectors and connect white wires (E)

together.

7. Connect green (or bare) ground wire from home power supply

to yellow-green ground wire (F) in terminal box using UL listed

wire connectors.

8. Tighten strain relief screw.

9. Install terminal box cover.

10. Check that all light bulbs are secure in their sockets.

11. Reconnect power.

A. Knockout

B. Terminal box

C. Terminal box cover

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

A. Home power supply cable

B. UL listed or CSA approved

strain relief

C. Black wires

D. UL listed wire connectors

E. White wires

F. Green (or bare) and yellow-

green ground wires

WARNING

Electrical Shock Hazard

Electrically ground blower.

Connect ground wire to green and yellow ground wire

in terminal box.

Failure to do so can result in death or electrical shock.

Install Duct Covers

NOTE: Remove the film from the duct covers.

1. Assemble the upper duct covers together and install the duct

covers around the support frame. The larger hole in the

flanges of the upper duct cover must be outside the smaller

hole in the mating flange of the other upper duct cover.

2. Secure the upper duct covers together with two 3.5 x 6.5 mm

screws at the top and two 2.9 x 3 mm screws at the bottom.

Install 1 screw on each side at the top and bottom of the

assembled duct covers.

NOTE: For non-vented (recirculating) installation, the slotted

holes in the upper duct covers will be visible when assembled.

For vented installations, the slotted holes will be hidden down

inside the lower duct covers.

3. Slide the upper duct covers up the frame to the ceiling and

secure to the upper horizontal support with 2 - 3.5 x 6.5 mm

screws.

4. Place the long end of the plastic clips (2) into the bottom of

the front lower duct cover.

5. Install the lower duct cover (front) to the range hood canopy.

Spread the lower duct cover opening slightly and position it

over the upper duct cover. Set the lower duct cover in place.

Position so the flanges of the lower duct cover set into the

flanges of the upper duct covers.

A. 3.5 x 6.5 mm screws (2)

B. Assembly holes (larger hole outside of

smaller hole on both sides)

C. 2.9 x 3 mm screws (2)

A. Top toward ceiling

B. Slots installed up for non-vented installations

C. Slots installed down for vented installations

A. 3.5 x 6.5 mm screw

B. Slotted holes (2)

C. Upper duct covers

D. Ceiling

A. Lower duct cover - (front)

B. Plastic clips (2) (long end for front placement)

A. Range hood canopy

B. Plastic clips

C. Lower duct covers

D. Upper duct covers

6. Install the lower duct cover (rear) to the range hood canopy.

Spread the lower duct cover opening slightly and position it

over the upper duct cover. Set the lower duct cover in place.

Position so the flanges of the lower duct cover set into the

flanges of the upper duct cover. Make sure the front and rear

lower duct covers mate properly.

NOTE:

When assembling the rear lower duct cover to the front

lower duct cover, the flange (both sides) must be placed over the

plastic clip to secure the lower duct covers together at the bottom.

7. Secure the lower duct covers together at the top using 2

plastic clips. Use one plastic clip on each side.

8. Secure the lower duct cover to the range hood canopy using

4 - 4.2 x 8 mm screws.

Complete Installation

1. For non-vented (recirculating) installations only, install

charcoal filters onto the metal filters. See the “Range Hood

Care” section.

2. Install metal filters. See the “Range Hood Care” section.

3. Check the operation of the range hood blower and light. See

the “Range Hood Use” section.

If range hood does not operate, check to see whether a

circuit breaker has tripped or a household fuse has blown.

NOTE: To get the most efficient use from your new range hood,

read the “Range Hood Use” section.

A. Lower duct cover (rear)

B. Plastic clips

C. Lower duct covers

D. Upper duct covers

A. Plastic clips (2)

B. Lower duct covers top clip area

RANGE HOOD USE

The range hood is designed to remove smoke, cooking vapors and

odors from the cooktop area. For best results, start the hood

before cooking and allow it to operate several minutes after the

cooking is complete to clear all smoke and odors from the kitchen.

The range hood controls are located on the front side of the canopy.

Control Panel

The range hood controls are located on the front side of the canopy.

Display

Grease Filter Saturation Alarm

After 30 hours of fan function, the display will show “Clean

Grease Filter” when the fan is active. When this icon shows in the

display, the installed grease filters should be washed. See

“Range Hood Care” section.

■ To reset the grease filter saturation alarm, press and hold the

POWER INCREASE button for 5 seconds. The “Clean Grease

Filter” icon will no longer be displayed.

Charcoal Filter Saturation Alarm

After 120 hours of fan function, the display will show “Replace

Charcoal Filter” when the fan is active. When this icon shows in

the display, the charcoal filters should be replaced. See “Range

Hood Care” section.

■ To reset the charcoal filter saturation alarm, press and hold

the POWER DECREASE button for 5 seconds. The “Replace

Charcoal Filter” icon will no longer be displayed.

Audible Signal Activation and Deactivation

The audible signals can be activated or deactivated by pressing

the “LIGHT” button for 5 seconds.

■ If the audible signal is activated, a tone will sound, and “Snd”

symbol will appear in the display for 3 seconds.

■ If the audible signal is deactivated, the “Snd” symbol will

appear on the display for 3 seconds.

Charcoal Filter (Recirculation Accessory) Inclusion

and Exclusion

When the charcoal filter is in use (recirculating mode), press and

hold the POWER DECREASE and POWER INCREASE buttons at

the same time for 5 seconds. “Able” will appear in the display for

3 seconds.

If the charcoal filter is not used (vented mode), press and hold the

POWER DECREASE and POWER INCREASE buttons at the

same time for 5 seconds. “None” will appear in the display for

3 seconds.

■ When the charcoal filter has been excluded, the charcoal filter

alarm is disabled.

■ The inclusion or exclusion of the charcoal filter must be

selected while the lights and the fan motor are Off.

Heat Sensor

The control is equipped with a heat sensor that will turn on the

blower to the highest speed if excessive heat occurs around the

control area.

■ If the blower is On or Off, the blower will automatically set to

the highest speed. “Auto” will appear in the display to

indicate that the heat sensor has detected excessive heat.

■ When the blower is operating due to excessive heat detected

by the heat sensor, the blower speed cannot be decreased.

■ When the temperature level on the hood drops to normal, the

blower will return to its setting before the excessive heat was

sensed.

Light

To operate the light:

1. Press the Light button to turn the light on to high.

2. Press the Light button again to turn the light to low.

3. Press the Light button a third time to turn the light off.

Timer

The timer can be set from 1 to 60 minutes. The default timer

setting is 10 minutes.

To use the timer:

1. Press the Timer button to enter the timer mode. After

5 seconds the default time will be automatically selected.

2. Press the POWER DECREASE and POWER INCREASE

buttons while the display is flashing (5 seconds) to adjust to

the desired time. Pressing the timer button again or waiting

5 seconds after selecting the desired time will start the timer

countdown.

3. The timer can be canceled at any time by pressing the Timer

button again.

NOTE: During the timer setup, the Power Decrease and Power

Increase buttons are dedicated to the timer. After the timer starts,

the Power Decrease and Power Increase buttons can be used for

other functions.

A. Louver holes (non-vented

[recirculating] installations only)

B. Duct covers

C. Lamp housings

D. Canopy

E. Grease filters

F. Grease filter handles

G. Control panel

A. Power decrease

B. Power increase

C. Display

D. Light

E. Timer

Fan Speed Buttons

Power Increase/On

This button is used to turn the fan On or increase the fan speed.

■ The fan will turn On if the Power Increase button is pressed

and the hood was Off.

■ An audible tone will sound when the fan reaches its highest

speed.

Power Decrease/Off

■ This button is used to turn the fan Off or to decrease the fan

speed.

RANGE HOOD CARE

Cleaning

IMPORTANT: Clean the hood and grease filters frequently

according to the following instructions. Replace grease filters

before operating hood.

Exterior Surfaces:

To avoid damage to the exterior surface, do not use steel wool or

soap-filled scouring pads.

Always wipe dry to avoid water marks.

Cleaning Method:

■ Liquid detergent soap and water, or all-purpose cleanser

■ Wipe with damp soft cloth or nonabrasive sponge, then rinse

with clean water and wipe dry.

Metal Grease Filter

The filters should be washed frequently. Place metal filters in

dishwasher or hot detergent solution to clean.

Let filter dry thoroughly before replacing it.

Turn off fan and lights. Allow halogen lamp to cool.

1. Remove each filter by pulling the spring release handle and

then pulling down the filter.

2. Wash metal filters as needed in dishwasher or hot detergent

solution.

Reinstall the filter by making sure the spring release handles

are toward the front. Insert metal grease filter into upper track.

4. Pull the spring release handle down.

5. Push up on metal filter and release handle to latch into place.

6. Repeat steps 1-5 for the other filter.

Non-Vented (recirculating) Installation Filters

The charcoal filter is not washable. It should last up to 6 months with

normal use. Replace with Charcoal Filter Kit Number W10272068.

To replace charcoal filter:

1. Cover the grille that covers the blower motor with the

charcoal filter so that the slots on the filter correspond to the

pins on the sides of the motor grille.

2. Turn the charcoal filter clockwise to lock it.

3. Repeat steps 1-2 on the other filter.

Replacing a Halogen Lamp

Turn off the range hood and allow the halogen lamp to cool. To

avoid damage or decreasing the life of the new lamp, do not

touch lamp with bare fingers. Replace lamp, using tissue or

wearing cotton gloves to handle lamp.

If new lights do not operate, make sure the lamps are inserted

correctly before calling service.

1. Disconnect power.

Use a flat-blade screwdriver and gently pry the light cover loose.

3. Remove the lamp and replace with a 120-volt, 40-watt

maximum, halogen lamp made for a G-9 base.

4. Replace the light cover.

5. Reconnect power.

A. Spring release handle

A. Charcoal filter

B. Pins

C. Blower motor

WIRING DIAGRAM

YL/GN

GND

YL/GN

P4A

Electronic Power Board

Electronic User Interface

Motor Resistance (Ohms)

Blue - Red

Blue - Gray

Blue - Black

Blue - White

Room Temp.

14.3

9.8

21.6

Motor Specifications

Power Supply

Frequency

Power Absorption

Current

120 VAC

60 HZ

450 W

3.7A

73.4°F (23°C)

4 Lamps only on

Island Versions

YL/GN

SE124A

ASSISTANCE OR SERVICE

If you need service

Please refer to the warranty page in this manual.

If you need replacement parts

If you need to order replacement parts, we recommend that you

use only factory specified parts. Factory specified parts will fit

right and work right because they are made with the same

precision used to build every new appliance.

To locate factory specified replacement parts in your area, call

the following customer assistance telephone number or your

nearest designated service center.

In the U.S.A.

Call Jenn-Air Customer eXperience Center toll free:

1-800-JENNAIR (1-800-536-6247) or visit our website at

www.jennair.com

Our consultants provide assistance with:

■ Scheduling of service. Jenn-Air

appliances designated

service technicians are trained to fulfill the product warranty

and provide after-warranty service, anywhere in the United

States.

■ Features and specifications on our full line of appliances.

■ Referrals to local Jenn-Air

appliance dealers.

■ Installation information.

■ Use and maintenance procedures.

■ Accessory and repair parts sales.

■ Specialized customer assistance (Spanish speaking, hearing

impaired, limited vision, etc.).

For further assistance

If you need further assistance, you can write to Jenn-Air

Appliances with any questions or concerns at:

Jenn-Air Brand Home Appliances

Customer eXperience Center

553 Benson Road

Benton Harbor, MI 49022-2692

Please include a daytime phone number in your correspondence.

Accessories

Charcoal Filter Kit

(for non-vented installations only)

Order Part Number W10272068

Recirculation Kit

(for non-vented installations only)

Order Part Number W10272061

Chimney Extension Kit

Order Part Number W10688278

6" (15.2 cm) Makeup Air Kit

(consult local building codes)

Order Part Number W10446915

In Canada

Call the Jenn-Air Canada LP Customer eXperience Centre toll

free at 1-800-JENNAIR (1-800-536-6247) or visit our website at

www.jennair.ca

Our consultants provide assistance with:

■ Scheduling of service. Jenn-Air

appliances designated

service technicians are trained to fulfill the product warranty

and provide after-warranty service, anywhere in the Canada.

■ Features and specifications on our full line of appliances.

■ Referrals to local Jenn-Air

appliance dealers.

■ Installation information.

■ Use and maintenance procedures.

■ Accessory and repair parts sales.

For further assistance

If you need further assistance, you can write to Jenn-Air

Appliances with any questions or concerns at:

Jenn-Air Brand Home Appliances

Customer eXperience Centre

200 - 6750 Century Ave

Mississauga, Ontario L5N 0B7

Please include a daytime phone number in your correspondence.

2/14

JENN-AIR

MAJOR

APPLIANCE

LIMITED WARRANTY

ATTACH YOUR RECEIPT HERE. PROOF OF PURCHASE IS REQUIRED

TO OBTAIN WARRANTY SERVICE.

Please have the following information available when you call the

Customer eXperience Center:

■ Name, address and telephone number

■ Model number and serial number

■ A clear, detailed description of the problem

■ Proof of purchase including dealer or retailer name and address

IF YOU NEED SERVICE:

1. Before contacting us to arrange service, please determine whether your product requires repair. Some

questions can be addressed without service. Please take a few minutes to review the Troubleshooting or

Problem Solver section of the Use and Care Guide, scan the QR code on the right to access additional

resources, or visit https://jennair.custhelp.com.

2. All warranty service is provided exclusively by our authorized Jenn-Air Service Providers. In the U.S. and

Canada, direct all requests for warranty service to:

Jenn-Air Customer eXperience Center

1-800-JENNAIR (1-800-536-6247)

If outside the 50 United States or Canada, contact your authorized Jenn-Air dealer to determine whether another warranty applies.

https://jennair.custhelp.com

ONE YEAR LIMITED WARRANTY

WHAT IS COVERED WHAT IS NOT COVERED

For one year from the date of purchase, when this major

appliance is installed, operated and maintained according to

instructions attached to or furnished with the product,

Jenn-Air brand of Whirlpool Corporation or Whirlpool

Canada LP (hereafter “Jenn-Air”) will pay for Factory

Specified Replacement Parts and repair labor to correct

defects in materials or workmanship that existed when this

major appliance was purchased, or at its sole discretion

replace the product. In the event of product replacement,

your appliance will be warranted for the remaining term of

the original unit's warranty period.

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS

LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS

PROVIDED HEREIN. Service must be provided by a

Jenn-Air designated service company. This limited warranty

is valid only in the United States or Canada and applies only

when the major appliance is used in the country in which it

was purchased. This limited warranty is effective from the

date of original consumer purchase. Proof of original

purchase date is required to obtain service under this limited

warranty.

1. Commercial, non-residential, multiple-family use, or use inconsistent with

published user, operator or installation instructions.

2. In-home instruction on how to use your product.

3. Service to correct improper product maintenance or installation, installation not

in accordance with electrical or plumbing codes or correction of household

electrical or plumbing (i.e. house wiring, fuses or water inlet hoses).

4. Consumable parts (i.e. light bulbs, batteries, air or water filters, preservation

solutions, etc.).

5. Conversion of products from natural gas or L.P. gas.

6. Damage from accident, misuse, abuse, fire, floods, acts of God or use with

products not approved by Jenn-Air.

7. Repairs to parts or systems to correct product damage or defects caused by

unauthorized service, alteration or modification of the appliance.

8. Cosmetic damage including scratches, dents, chips, and other damage to the

appliance finishes unless such damage results from defects in materials and

workmanship and is reported to Jenn-Air within 30 days.

9. Discoloration, rust or oxidation of surfaces resulting from caustic or corrosive

environments including but not limited to high salt concentrations, high moisture

or humidity or exposure to chemicals.

10. Food or medicine loss due to product failure.

11. Pick-up or delivery. This product is intended for in-home repair.

12. Travel or transportation expenses for service in remote locations where an

authorized Jenn-Air servicer is not available.

13. Removal or reinstallation of inaccessible appliances or built-in fixtures (i.e. trim,

decorative panels, flooring, cabinetry, islands, countertops, drywall, etc.) that

interfere with servicing, removal or replacement of the product.

14. Service or parts for appliances with original model/serial numbers removed,

altered or not easily determined.

The cost of repair or replacement under these excluded circumstances shall

be borne by the customer.

DISCLAIMER OF IMPLIED WARRANTIES

IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR A

PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces do not allow

limitations on the duration of implied warranties of merchantability or fitness, so this limitation may not apply to you. This warranty gives you

specific legal rights, and you also may have other rights that vary from state to state or province to province.

DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY

Jenn-Air makes no representations about the quality, durability, or need for service or repair of this major appliance other than the representations

contained in this warranty. If you want a longer or more comprehensive warranty than the limited warranty that comes with this major appliance,

you should ask Jenn-Air or your retailer about buying an extended warranty.

LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. JENN-AIR

SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow the exclusion or limitation

of incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty gives you specific legal rights, and

you also may have other rights that vary from state to state or province to province.

SÉCURITÉ DE LA HOTTE DE CUISINIÈRE

Risque possible de décès ou de blessure grave si vous ne

suivez pas immédiatement les instructions.

Risque possible de décès ou de blessure grave si vous

ne suivez pas les instructions.

Tous les messages de sécurité vous diront quel est le danger potentiel et vous disent comment réduire le risque de blessure et

ce qui peut se produire en cas de non-respect des instructions.

Votre sécurité et celle des autres est très importante.

Nous donnons de nombreux messages de sécurité importants dans ce manuel et sur votre appareil ménager. Assurez-vous de

toujours lire tous les messages de sécurité et de vous y conformer.

AVERTISSEMENT

DANGER

Voici le symbole d’alerte de sécurité.

Ce symbole d’alerte de sécurité vous signale les dangers potentiels de décès et de blessures graves à vous

et à d’autres.

Tous les messages de sécurité suivront le symbole d’alerte de sécurité et le mot “DANGER” ou

“AVERTISSEMENT”. Ces mots signifient :

Avertissements de la proposition 65 de l'État de Californie :

AVERTISSEMENT : Ce produit contient au moins un produit chimique connu par l’État de Californie pour être à l’origine de

cancers.

AVERTISSEMENT : Ce produit contient au moins un produit chimique connu par l’État de Californie pour être à l’origine de

malformations et autres déficiences de naissance.

IMPORTANTES INSTRUCTIONS DE SÉCURITÉ

LIRE ET CONSERVER CES INSTRUCTIONS

AVERTISSEMENT : POUR RÉDUIRE LE RISQUE

D'INCENDIE, CHOC ÉLECTRIQUE OU DOMMAGES

CORPORELS, RESPECTER LES INSTRUCTIONS

SUIVANTES :

■ Utiliser cet appareil uniquement dans les applications

envisagées par le fabricant. Pour toute question, contacter

le fabricant.

■ Avant d'entreprendre un travail d'entretien ou de nettoyage,

interrompre l'alimentation de la hotte au niveau du tableau

de disjoncteurs, et verrouiller le tableau de disjoncteurs

pour empêcher tout rétablissement accidentel de

l'alimentation du circuit. Lorsqu'il n'est pas possible de

verrouiller le tableau de disjoncteurs, placer sur le tableau

de disjoncteurs une étiquette d'avertissement proéminente

interdisant le rétablissement de l'alimentation.

■ Tout travail d'installation ou câblage électrique doit être

réalisé par une personne qualifiée, dans le respect des

prescriptions de tous les codes et normes applicables, y

compris les codes du bâtiment et de protection contre les

incendies.

■ Ne pas faire fonctionner un ventilateur dont le cordon ou la

fiche est endommagé(e). Jeter le ventilateur ou le retourner

à un centre de service agréé pour examen et/ou réparation.

■ Une source d'air de débit suffisant est nécessaire pour le

fonctionnement correct de tout appareil à gaz (combustion

et évacuation des gaz à combustion par la cheminée), pour

qu'il n'y ait pas de reflux des gaz de combustion. Respecter

les directives du fabricant de l'équipement de chauffage et

les prescriptions des normes de sécurité - comme celles

publiées par la National Fire Protection Association (NFPA)

et l'American Society for Heating, Refrigeration and Air

Conditioning Engineers (ASHRAE), et les prescriptions des

autorités réglementaires locales.

■ Lors d'opérations de découpage et de perçage dans un mur

ou un plafond, veiller à ne pas endommager les câblages

électriques ou canalisations qui peuvent s'y trouver.

■ Les ventilateurs d'évacuation doivent toujours décharger

l'air à l'extérieur.

MISE EN GARDE : Cet appareil est conçu uniquement

pour la ventilation générale. Ne pas l'utiliser pour l'extraction

de matières ou vapeurs dangereuses ou explosives.

MISE EN GARDE : Pour minimiser le risque d'incendie

et évacuer adéquatement les gaz, veiller à acheminer l'air

aspiré par un conduit jusqu'à l'extérieur - ne pas décharger

l'air aspiré dans un espace vide du bâtiment comme une

cavité murale, un plafond, un grenier, un vide sanitaire ou

un garage.

AVERTISSEMENT : POUR RÉDUIRE LE RISQUE

D'INCENDIE, UTILISER UNIQUEMENT DES CONDUITS

MÉTALLIQUES.

AVERTISSEMENT : POUR MINIMISER LE RISQUE

D'UN FEU DE GRAISSE SUR LA CUISINIÈRE :

■ Ne jamais laisser un élément de surface fonctionner à

puissance de chauffage maximale sans surveillance. Un

renversement/débordement de matière graisseuse pourrait

provoquer une inflammation et la génération de fumée.

Utiliser une puissance de chauffage moyenne ou basse

pour le chauffage d'huile.

■ Veiller à toujours faire fonctionner le ventilateur de la hotte

lors de la cuisson avec une puissance de chauffage élevée

ou lors de la cuisson d'un mets à flamber (à savoir crêpes

Suzette, cerise jubilée, steak au poivre flambé).

■ Nettoyer fréquemment les ventilateurs d'extraction. Veiller à

ne pas laisser la graisse s'accumuler sur les surfaces du

ventilateur ou des filtres.

■ Utiliser toujours un ustensile de taille appropriée. Utiliser

toujours un ustensile adapté à la taille de l'élément

chauffant.

AVERTISSEMENT : POUR RÉDUIRE LE RISQUE DE

DOMMAGES CORPORELS APRÈS LE DÉCLENCHEMENT

D'UN FEU DE GRAISSE SUR LA CUISINIÈRE, APPLIQUER

LES RECOMMANDATIONS SUIVANTES :

■ Placer sur le récipient un couvercle bien ajusté, une tôle à

biscuits ou un plateau métallique POUR ÉTOUFFER LES

FLAMMES, puis éteindre le brûleur. VEILLER À ÉVITER

LES BRÛLURES. Si les flammes ne s'éteignent pas

immédiatement, ÉVACUER LA PIÈCE ET APPELER LES

POMPIERS.

■ NE JAMAIS PRENDRE EN MAIN UN RÉCIPIENT

ENFLAMMÉ - vous risquez de vous brûler.

■ NE PAS UTILISER D'EAU, ni un torchon humide - ceci

pourrait provoquer une explosion de vapeur brûlante.

■ Utiliser un extincteur SEULEMENT si :

– Il s'agit d'un extincteur de classe ABC, dont on connaît le

fonctionnement.

– Il s'agit d'un petit feu encore limité à l'endroit où il s'est

déclaré.

– Les pompiers ont été contactés.

– Il est possible de garder le dos orienté vers une sortie

pendant l'opération de lutte contre le feu.

Recommandations tirées des conseils de sécurité en cas

d'incendie de cuisine publiés par la NFPA.

■ AVERTISSEMENT : Pour réduire le risque d'incendie

ou de choc électrique, ne pas utiliser ce ventilateur avec un

quelconque dispositif de réglage de la vitesse à semi-

conducteurs.

EXIGENCES D'INSTALLATION

Outils et pièces

Rassembler les outils et pièces nécessaires avant d’entreprendre

l’installation. Lire et observer les instructions fournies avec

chacun des outils de la liste ci-dessous.

Outils nécessaires

■ Niveau

■ Perceuse avec forets de 1¼" (3 cm), ³⁄₈" (9,5 mm), ⁷⁄₆₄"

(2,75 mm) et forets de ¹⁄₈" (3 mm)

■ Forets à avant-trou (selon la méthode de fixation du support

de cheminée)

■ Crayon

■ Pince à dénuder ou couteau utilitaire

■ Mètre-ruban ou règle

■ Pince

■ Pistolet à calfeutrage et composé de calfeutrage résistant

aux intempéries

■ Brides de conduit

■ Scie sauteuse ou scie à guichet

■ Tournevis à lame plate

■ Cisaille de ferblantier

■ Tournevis Phillips

Pièces nécessaires

■ Câble d'alimentation électrique du domicile

■ 2 serre-câbles de ½" (12,7 mm) (homologation UL ou CSA)

■ 3 connecteurs de fils homologués UL

Pour les installations avec décharge à l’extérieur, il vous

faudra aussi :

■ 1 bouche de décharge (décharge à travers le mur ou à travers

le toit)

■ Circuit d’évacuation métallique

Pour les installations sans décharge à l’extérieur (recyclage),

il faudra aussi :

■

Ensemble de filtre à charbon, pièce numéro W10272068 pour les

installations sans décharge à l'extérieur (recyclage) uniquement.

Voir la section “Assistance ou service” pour commander.

■

Ensemble de recyclage, pièce numéro W10272061 pour les

installations sans décharge à l'extérieur (recyclage) uniquement.

Voir la section “Assistance ou service” pour commander.

■ Conduit métallique dia. 8" (20,3 cm). La longueur nécessaire

est fonction de la hauteur sous plafond.

Pièces fournies

Retirer les pièces de leur emballage. Vérifier que toutes les

pièces sont présentes.

■ Auvent de hotte avec ventilateur et lampes installés

■ Filtre—installé sur la hotte

■ Vis de 4,2 x 8 mm (64)

■ Vis de 5 x 45 mm (4)

■ Gabarit de montage

■ 2 - cache-conduits – section supérieure

■ 2 - cache-conduits – section inférieure

■ Raccord de transition avec clapet anti-reflux installé

■ 4 attaches de conduit en plastique

■ Bride de support horizontal supérieur

■ Support horizontal

■ 8 supports verticaux

■ Vis de 3,5 x 6,5 mm (4)

■ Vis de 2,9 x 3 mm (2)

■ Adaptateur Torx

®†

T10

■ Adaptateur Torx

T20

Exigences d'emplacement

IMPORTANT : Observer les dispositions de tous les codes et

règlements en vigueur.

Confier l'installation de la hotte à un technicien qualifié. C'est à

l'installateur qu'incombe la responsabilité de respecter les

distances de séparation exigées, spécifiées sur la plaque

signalétique de l'appareil. La plaque signalétique de l'appareil est

située derrière le filtre de gauche, sur la paroi arrière de la hotte.

On doit toujours installer la hotte à distance des sources de

courant d'air (fenêtres, portes et bouches de chauffage).

Respecter les dimensions indiquées pour les ouvertures à

découper dans les placards; ces dimensions tiennent compte

des valeurs minimales des dégagements de séparation.

On doit disposer d'une prise de courant électrique reliée à la

terre. Voir la section “Spécifications électriques”.

Du fait du poids et de la taille de cette hotte d’extraction en îlot, il

faut que le support de cheminée soit solidement fixé au plafond.

■ Pour un plafond en plâtre ou en panneaux de gypse, le

support de cheminée doit être fixé aux solives. Si ceci n’est

pas possible, on doit construire une structure de support

appropriée derrière le plafond en plâtre ou panneaux de

gypse. La structure de support doit être capable de soutenir

une charge de 80 lb. (36,6 kg).

Il est recommandé d'utiliser cette hotte avec une table de

cuisson dont la puissance totale ne dépasse pas 60 000 BTU.

Cette hotte a été configurée à l’usine pour une décharge à travers

le toit.

Pour une installation sans décharge à l'extérieur (recyclage), voir

“Installations sans décharge à l’extérieur (recyclage)” à la section

“Installation de la hotte”. L’ensemble de recyclage (pièce numéro

W10272061) est disponible chez votre marchand ou chez un

distributeur de pièces autorisé.

Assurer l'étanchéité au niveau de chaque ouverture découpée dans

le plafond ou le mur pour l'installation de la hotte de cuisinière.

Installation dans une résidence mobile

L'installation de cette hotte doit satisfaire aux exigences de la

norme Manufactured Home Construction Safety Standards, Titre

24 CFR, partie 328 (anciennement Federal Standard for Mobile

Home Construction and Safety, titre 24, HUD, partie 280); lorsque

cette norme n'est pas applicable, l'installation doit satisfaire aux

critères de la plus récente édition de la norme Manufactured

Home Installation 1982 (Manufactured Home Sites, Communities

and Setups) ANSI A225.1/NFPA 501A, ou des codes et

règlements locaux applicables.

Dimensions du produit

*Installations avec décharge à l’extérieur uniquement

**Installation sans décharge à l’extérieur (recyclage) uniquement

†®TORX et T20 sont des marques déposées de Acument Intellectual Properties, LLC.

12¹⁄₄"

(31,0 cm)

13³⁄₁₆"

(33,5 cm)

36" (91,2 cm)

42" (106,4 cm)

*32¹⁄₂"

(82,6 cm)

min.

*46¹⁄₂"

(118,0 cm)

max.

**32¹⁄₂"

(82,6 cm)

min.

**52⁹⁄₁₆"

(133,5 cm)

max.

27" (68,6 cm)

Dimensions d’installation

IIMPORTANT :

Valeur minimale de la distance “C” : 24" (61 cm) à partir de la

surface de cuisson électrique.

Valeur minimale de la distance “C” : 27" (68,6 cm) à partir de la

surface de cuisson au gaz.

Valeur maximale suggérée pour la distance “C” : 36" (91,4 cm)

Les cache-conduits peuvent être adaptés à différentes hauteurs

de plafond. Voir le tableau suivant.

*REMARQUE : Les cache-conduits de la hotte sont réglables; on

peut les ajuster en fonction de la hauteur disponible sous

plafond ou soffite, et selon la distance “C” entre le bas de la

hotte et la surface de cuisson. Pour des hauteurs sous plafond

plus élevées, un ensemble d’extension de cache-conduit en

acier inoxydable (pièce n° W10688278) est disponible chez votre

marchand ou chez un distributeur de pièces autorisé.

L’extension de cache-conduit remplace la section supérieure de

cache-conduit fournie avec la hotte.

Exigences concernant

l'évacuation

■ Le système d'évacuation doit décharger l'air à l'extérieur,

excepté pour les installations sans décharge à l'extérieur

(recyclage).

■ Ne pas terminer le conduit d'évacuation dans un grenier

dans un autre espace fermé.

■ Ne pas utiliser une bouche de décharge murale de 4"

(10,2

cm) normalement utilisée pour un équipement

buanderie.

■ Utiliser un conduit métallique uniquement. Un conduit en

métal rigide est recommandé. Ne pas utiliser de conduit de

plastique ou d'aluminium.

■ Le système d'évacuation doit comporter un clapet. Si la

bouche de décharge murale ou par le toit comporte un

clapet, ne pas utiliser le clapet fourni avec la hotte de

cuisinière.

Pour un fonctionnement efficace et silencieux :

■ Utiliser autant que possible des sections droites et minimiser

le nombre de coudes.

■ Ne pas utiliser plus de trois coudes à 90°.

■ Veiller à ce qu'il y ait une section droite de conduit de 24"

(61

cm) ou plus entre deux coudes, si on doit utiliser plus

d’un raccord coudé.

■ Ne pas installer 2 coudes ensemble.

■ Au niveau de chaque jointure du conduit de décharge,

assurer l'étanchéité avec les brides de serrage pour conduit.

■ Autour de la bouche de décharge à l'extérieur par le toit ou

par un mur, assurer l'étanchéité avec un produit de

calfeutrage.

■ La taille du conduit doit être uniforme.

Installations dans une région à climat froid

Dans le circuit d'évacuation, on devrait installer un clapet anti-

reflux additionnel pour minimiser le reflux d'air froid, ainsi qu'un

élément d'isolation thermique pour minimiser le transfert de

chaleur par conduction vers l'extérieur. Le clapet anti-reflux doit

être placé du côté air froid par rapport à l'élément d'isolation

thermique.

L'élément d'isolation thermique doit être aussi proche que

possible de l'endroit où le système d'évacuation s'introduit dans

la partie chauffée de la maison.

Air d'appoint

Le code du bâtiment local peut exiger l'emploi d'un système de

renouvellement de l'air/introduction d'air d'appoint, lors de

l'utilisation d'un système d'aspiration de débit supérieur à une

valeur (pieds cubes par minute) spécifiée. Le débit spécifié, en

pieds cubes par minute, est variable d'une juridiction à une autre.

Consulter un professionnel des installations de chauffage

ventilation/climatisation au sujet des exigences spécifiques

applicables dans la juridiction locale.

Méthodes d'évacuation

Cette hotte a été configurée à l’usine pour la décharge à travers

le toit.

Un circuit d'évacuation en conduit rond de 8" (20,3 cm) est

nécessaire pour l'installation (non fourni). La hotte comporte une

ouverture de sortie de diamètre 8" (20,3 cm).

REMARQUE : On déconseille l'emploi d'un conduit flexible. Un

conduit flexible peut causer une rétropression et des turbulences

de l'air, ce qui réduit considérablement la performance.

La sortie à l'extérieur du circuit d'évacuation peut se faire à

travers le toit ou à travers un mur. Pour la sortie à travers un mur,

on doit employer un raccord coudé de 90°.

A. Hauteur sous plafond

B. Hauteur sous hotte entre le plafond et le bas

de la hotte : A-C-D = B

C. Hauteur sous hotte suggérée de 24" (61 cm)

minimum à 36" (91,4 cm) maximum

D. Hauteur du plan de travail

Installations avec décharge à l’extérieur

Hauteur min. sous

plafond

Hauteur max.

sous plafond

Surface de

cuisson électrique

7' 9" (2,36 m) 9' 10" (3,0 m)

Surface de

cuisson au gaz

8' (2,44 m) 9' 10" (3,0 m)

Installations sans décharge à l’extérieur (recyclage)

Hauteur min. sous

plafond

Hauteur max.

sous plafond

Surface de

cuisson électrique

7' 9" (2,36 m) 10' 4" (3,15 m)

Surface de

cuisson au gaz

8' (2,44 m) 10' 4" (3,15 m)

C A

La page charge ...

Jenn-Air 42 inch Manuel utilisateur

Marque: Jenn-Air

Modèle: 42 inch

Catégorie: Hottes

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Jenn-Air 42 inch User manual

Jenn-Air 42 inch Manuel utilisateur

Ce manuel convient également à

Jenn-Air 42 inch Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents