Sage SES875 the Barista Express Manuel utilisateur

Catégorie
Cafetières
Taper
Manuel utilisateur
the User Guide
B###### / S######
EN QUICK GUIDE
FR GUIDE RAPIDE
IT GUIDA RAPIDA
PT MANUAL RÁPIDO
DE KURZANLEITUNG
NL SNELSTARTGIDS
ES GUÍA RÁPIDA
PL SZYBKI PRZEWODNIK
the Barista Express
BES875 / SES875
2
2 Sage® Recommends Safety First
6 Components
8 Functions
15 Care & Cleaning
19 Troubleshooting
23 Guarantee
Contents
The installation of a residual
current safety switch is
recommended to provide
additional safety when using
all electrical appliances.
Safety switches with a rated
operating current not more
than 30mA are recommended.
Consult an electrician for
professional advice.
Remove and discard any
packaging materials safely,

To eliminate a choking hazard
for young children, discard the

power plug safely.
Ensure the product is properly

This appliance is for household
use only. Do not use the
appliance for anything other
than its intended purpose.
Do not use in moving vehicles
or boats. Do not use outdoors.
Misuse may cause injury.
Position the appliance on a
stable, heat resistant, level, dry
surface away from the counter
edge, and do not operate on
or near a heat source such as
a hot plate, oven or gas hob.
Fully unwind the power cord
before operating.
Do not let the power cord
hang over the edge of a
counter or table. Do not let the
power cord touch hot surfaces
or become knotted.
SAGE®
RECOMMENDS
SAFETY FIRST
At Sage® we are very safety
conscious. We design and
manufacture appliances
with your safety foremost in
mind. We also ask that you
exercise a degree of care
when using any electrical
appliance and adhere to
the following precautions.
READ ALL INSTRUCTIONS
BEFORE USE AND SAVE
FOR FUTURE REFERENCE
A downloadable version of this
document is also available at
sageappliances.com

time, please ensure that your
electricity supply is the same
as shown on the rating label
on the underside of the
appliance. If you have any
concerns please contact your
local electricity company.
3
EN
Do not leave the appliance
unattended when in use.
If the appliance is to be:
- left unattended
- cleaned
- moved
- assembled; or
- stored

machine by pressing the
POWER button to OFF.

the power outlet.
Regularly inspect the power
cord, plug and actual appliance
for any damage. If found to
be damaged in any way,
immediately cease use of
the appliance and return the
entire appliance to the nearest
authorised Sage Service
Centre for examination,
replacement or repair.
Keep the appliance and
accessories clean. Follow
the cleaning instructions
provided in this book. Any
procedure not listed in this
instruction booklet should be
performed at an authorised
Sage Service Centre.
The appliance can be used by
children aged 8 or older and
persons with reduced physical,
sensory or mental capabilities
or a lack of experience and
knowledge, only if they have
been given supervision or
instruction concerning use
of the appliance in a safe
way and understand the
hazards involved.
Children should not play with
the appliance.
Cleaning of the appliance should
not be carried out by children
unless they are 8 years or older
and under adult supervision.
The appliance and its cord should
be kept out of reach of children
aged 8 years and younger.
Do not use attachments
other than those provided
with the appliances.
Do not attempt to operate
the appliance by any method
other than those described
in this booklet.
Do not move the appliance
whilst in operation.
Do not use any other liquid
apart from cold mains/town
water. We do not recommend

de-mineralised or distilled water


machine is designed to function.
Never use the appliance without
water in the water tank.


into the brewing head before
using the machine.

during the brewing operation as
the machine is under pressure.
4
Do not place anything, other
than cups on top of the
appliance.
Use caution when operating
machine as metal surfaces are
liable to get hot during use.
Do not touch hot surfaces.
Allow the product to cool
down before moving or
cleaning any parts.
Heating element surface
is subject to residual heat
after use.
The appliance is not intended
to be operated by means of
an external timer or separate
remote-control system.
Always turn the appliance to

the power outlet and unplug
at the power outlet when the
appliance is not in use.
Any maintenance other
than cleaning should be
performed by an authorised
Sage® service centre.
Do not use the appliance on
a sink drain board, wooden or
porous surfaces.
Do not operate the appliance
if it is in an enclosed space,
or within a cupboard.
Use caution when descaling
as hot steam may be released.
Before descaling, ensure drip
tray is empty and inserted.
Refer to ‘Care & Cleaning’ for
further instructions.
Do not operate the grinder
without the hopper lid in

hands, hair, clothing and
utensils away from the
hopper during operation.
SPECIFIC INSTRUCTIONS
FOR WATER FILTER
Filter cartridge should be kept
out of reach of children.

place in the original packaging.
Protect cartridges from heat
and direct sunlight.
Do not use damaged


If you are absent for a prolonged
period of time, empty the water
tank and replace the cartridge.
FOR HOUSEHOLD USE ONLY
SAVE THESE INSTRUCTIONS
5
EN
The symbol shown
indicates that this appliance
should not be disposed of
in normal household waste.
It should be taken to a local
authority waste collection centre
designated for this purpose or
to a dealer providing this service.
For more information, please

To protect against electric
shock, do not immerse
the power cord, power plug
or appliance in water or any
other liquid.
6
Components
A
B
G
D
H
I
C
E
J
R
K
L
SV
U
T
N
Q
O
F
M
P
```
A. 250g bean hopper
B. Integrated conical burr grinder
C. Grind outlet
D. Grinding activation switch
E. Hands free grinding cradle
F. GRIND SIZE selector
G. GRIND AMOUNT dial
H. FILTER SIZE button
I. POWER button
J. Integrated removable 54mm tamper
K. Group head
 
M. Extra-tall cup clearance for tall mugs
N. 
drip tray
 
P. Dedicated hot water outlet
Q. Steam/Hot Water dial
R. Steam/Hot Water light
S 1 CUP and 2 CUP buttons
T. CLEAN ME light
U. Espresso pressure gauge
V. Programme button
Re-programs the preset 1 CUP
and 2 CUP shot volumes.
Rating Information
7
EN
ACCESSORIES
1. Temp Control Milk Jug
2. Cleaning disc
3. Cleaning tablets
 

 
(1 cup & 2 cup) Use when grinding

 
7. Cleaning brush
8. The Razor precision dose trimming tool
9. Cleaning tool
10. Allen key
11. Descaling powder
12. The Dosing Funnel 54
3
2
5
4
1
6
8
9
10
7
11 12
220–240V ~50Hz 15601850W
8
INSTALLING THE WATER FILTER

from the plastic bag.
 
 
Set the reminder for next month of replacement.

3 months.
 

 

with the adapter inside the water tank.
Push down to lock into place.
Fill the water tank with cold tap water before
sliding back into position at the back of the
machine and locking into place.
FIRST USE
 
the water tank.
Fill the water tank with cold water up to the
MAX mark.
Ensure the hopper is locked into position.
Plug the power cord into a 230V power outlet.
Press the POWER button to switch the machine

machine is heating.
Place a large heat proof bowl under the group
head.
NOTE
If the hopper is not correctly locked into position,

1. Press 2 CUP button to run hot water through
the group head.
2. Position the steam wand tip over the drip tray.
Rotate the STEAM / HOT WATER dial to the
STEAM position and run steam through the
steam wand for 10 seconds.
3. Rotate the STEAM/HOT WATER dial
to the HOT WATER position and run water
through the hot water outlet for 10 seconds.
4. Repeat steps 1-3 until the water tank is empty.
Functions
9
EN
GENERAL OPERATION
Setting the Grind Size



We recommend you start at setting 8 and adjust
as required.
Setting the Grind Amount
Set the GRIND AMOUNT dial to the 3 o’clock
position as a starting point. Adjust towards LESS
or MORE as required to adjust the dose amount.





Selecting the Filter Size




Attach and twist the dosing funnel onto

 
the grinding cradle.
Automatic Dosing
 
the grinding activation switch.
Grinding will automatically stop, however
if you wish to stop grinding before the cycle

Manual Dosing
 
grinding activation switch. Continue holding

has been dosed.
 

 
After tamping, remove the dosing funnel from the

NOTE
As a guide to dose, the top edge of the metal cap
on the tamper should be level with the top of the

10

Press the 1 CUP button once to extract
a single shot of espresso at the preset volume
(approx. 30ml).
NOTE
Pressing the 1 CUP or 2 CUP button during
a preset shot volume will immediately stop
the extraction.

Press the 2 CUP button once to extract
a double shot of espresso at the preset volume
(approx. 60ml).
Re-Programming
Shot Volume – 1 CUP or 2 Cup
1. To begin programming, press the Programme
button once.
2. Press 1 CUP or 2 CUP button to start espresso
extraction. Press 1 CUP or 2 CUP button
again once desired volume of espresso has
been extracted. The machine will beep twice
to indicate the new 1 CUP or 2 CUP volume
has been set.
Resetting Default Volumes
To reset the machine to the default 1 CUP
and 2 CUP shot volumes, press and hold the
PROGRAMME button until the machine beeps
three times. Release the PROGRAMME button.
NOTE
Default settings: 1 CUP shot volume is approx.
30ml. 2 CUP shot volume is approx. 60ml.
Trimming the Dose
The Razor precision dose trimming tool
allows you to trim the puck to the right level
for a consistent extraction.
Insert the Razor dose trimming tool into the

on the rim of the basket.
Rotate the Razor dose trimming tool back



Purging the Group Head


group head by pressing the 1 CUP button
approximately 5 seconds to get rid of the left
over grind and stabilize the temperature.

WARNING

funnel in the group-head.

rotate the handle towards the centre until
resistance is felt.
11
EN
EXTRACTION GUIDE
Manual Shot Volume
Press and hold the 1 CUP or 2 CUP button.
The extraction will enter low pressure pre-
infusion until the button is released. When the
1 CUP or 2 CUP button is released, extraction
will continue at full pressure. Press the 1 CUP
or 2 CUP button again once the desired volume
of espresso has been extracted.
Within
Espresso Range Under
Espresso Range
• Flow starts after 8–12 secs
• Flow slow like warm honey
• Crema is golden brown with a fine
mousse texture
• Espresso is dark brown
• Extraction takes 2530 secs
SOLUTIONS SOLUTIONS
Over
Espresso Range
• Flow starts after 1–7 secs
• Flow fast like water
• Crema is thin and pale
• Espresso is pale brown
• Tastes bitter/sharp, weak and watery
• Extraction takes up to 20 secs
• Flow starts after 12 secs
• Flow drips or not at all
• Crema is dark and spotty
• Espresso is very dark brown
• Tastes bitter and burnt
• Extraction takes more than 35 secs
REMOVE USED
GRINDS
Used grinds will form
a coffee ‘puck’. If the
puck is wet, refer to
the ‘Under Extraction’
section.
FILTERSIEB
SPÜLEN
RINSE FILTER
BASKET
Keep the filter basket
clean to prevent
blockages. Without
ground coffee in the
filter basket, lock the
portafilter into the
machine and run hot
water through.
AFTER EXTRACTION
CORRECT EXTRACTION UNDER EXTRACTION OVER EXTRACTION
TURN
Grind Finer
Tamp using 10-15kg
of pressure. The top
edge of metal cap on
the tamper should be
level with the top of the
filter basket AFTER
tamping. Remove the
dosing funnel from the
portafilter then trim the
puck to the right level
using the Razor
precision dose
trimming tool.
GRIND SIZE
FINER
Adjust & re-test
Grind Coarser
Tamp using 10-15kg
of pressure. The top
edge of metal cap on
the tamper should be
level with the top of the
filter basket AFTER
tamping. Remove the
dosing funnel from the
portafilter then trim the
puck to the right level
using the Razor
precision dose
trimming tool.
GRIND SIZE
COARSER
Adjust & re-test
TURN
12
Set the jug to one side. Immediately wipe the
steam wand with a damp cloth. Then, with
the steam wand tip directed over the drip tray,

milk from inside the steam wand.
Pour milk directly into the espresso.
NOTE
After 5 minutes of continuous steaming, the
machine will automatically disable the steam
function. The STEAM/HOT WATER light will

STANDBY position.
Hot Water
Turn the STEAM/HOT WATER dial to the
HOT WATER position.
To stop the hot water, return the dial to the
STANDBY position.
USING THE STEAM / HOT WATER DIAL
Steam
Position the steam wand tip over the drip tray.
Turn the STEAM / HOT WATER dial to the
STEAM position. The STEAM / HOT WATER

to create steam.
When the STEAM/HOT WATER light stops

position.
Then within 8 seconds, insert the steam wand
tip (1–2cm) below the surface of the milk, close
to the right hand side of the jug at the 3 o’clock
position and quickly turn the dial back to the
STEAM position. Pausing the steam avoids the
milk splashing out of the jug (this pause function
lasts for 8 seconds only).
The indicator strip on the milk jug will change
colour to highlight the exact milk temperature.
We recommend milk temperature to be between
60-65°C.
Once the milk is at the correct temperature
(60–65°C), return the dial to the STANDBY
position BEFORE removing the jug.
EXTRACTION GUIDE
TOO
COARSE
UNDER
20 SEC
10-15KG
TOO FINE OVER
35 SEC
TOO MUCH
USE RAZOR
TO TRIM 10-15KG
25-30 SECOPTIMUM 10-15KG
8-11g (1 CUP)
16-19g (2 CUP)
TOO LITTLE
INCREASE DOSE
& USE RAZOR
TO TRIM
OVER EXTRACTED
BITTER • ASTRINGENT
BALANCED
GRIND DOSE TAMP SHOT TIME
UNDER EXTRACTED
UNDERDEVELOPED • SOUR
13
EN
ADVANCED TEMPERATURE MODE
Adjusting Water Temperature
To enter Advanced Temperature Mode:
1. Press the POWER button to switch the

2. Press & hold the PROGRAMME button, then
press the POWER button. The machine will
beep once. The illuminated button will indicate
the current temperature selected. To adjust the
water temperature, press one of the following
buttons within 5 seconds of entering Advanced
Temperature Mode. The machine will beep

are pressed within 5 seconds after entering
Advanced Temperature Mode, no change will
be made & the machine will return to STANDBY
mode.
Default Temperature setting:
In Advanced Temperature Mode,
press the Programme button.

In Advanced Temperature Mode,
press the 1 CUP button.

In Advanced Temperature Mode,
press the 2 CUP button.

In Advanced Temperature Mode,
press the FILTER SIZE button.

In Advanced Temperature Mode,
press the POWER button.
AUTO OFF MODE
The machine automatically switches
to AUTO OFF mode after 30 minutes
as per compliance regulations.
14
ADJUSTING CONICAL BURRS

A feature of the Barista Express is the ability to extend this range with an adjustable upper burr.
We recommend making only one adjustment at a time.
Lock upper burr
Hold hopper over container & turn
dial to release beans into container Align hopper
into position Run grinder
until empty Remove hopperUnlock hopper
Move adjustable
top burr, 1 number,
coarser or finer
Remove wire
handle from both
sides of the burr
Align the number
with the handle
opening
Remove upper
burr
Insert wire
handle from both
sides of the burr
Push upper burr
firmly into
position
Align hopper
into position
Lock hopper Check your
extraction
15
EN
Care & Cleaning
Soak lter
for 5 min
Ensure parts are
connected
Install lter in tank Install water tankSet current month
1
Replace lter after
90 days or after 40L
!
22 3 54

of scale build-up in and on many of the inner
functioning components. Replacing the water

the need to descale the machine.
The limitation of 40L is based on water hardness
level 4. If you are in level 2 area, you can increase
this to 60L.
WARNING
After regular use, hard water can cause mineral
build up in and on many of the inner functioning

temperature, power of the machine, and taste
of the espresso.
CLEANING CYCLE
The CLEAN ME light will illuminate when a
cleaning cycle is required. This is separate from
descaling.
1. 

disc, followed by 1 cleaning tablet.
2. 
3. 
and the drip tray is empty.
4. Press the POWER button to switch the

5. Press the 1 CUP and 2 CUP buttons
simultaneously, then also press the POWER
button. Hold all 3 buttons together for
approximately 3 seconds.
6. The cleaning cycle will commence and last
for approximately 5 minutes. During this



cleaning disc is without a hole in the middle,
hardly any or no water should come through

7. 
has completely dissolved. If the tablet has
not dissolved; repeat from step 4 of the
cleaning cycle until the tablet is dissolved.
8. Once the tablet has completely dissolved,
remove the cleaning disc, reinsert the

rinse the brew head. We recommend to

to avoid water splashing onto the machine.

splashes with a soft dry cloth.
DESCALING
NOTE

water tank before adding the descaling powder
when descaling the machine.
NOTE
The machine will not automatically prompt
a reminder when it is time to run a descaling
cycle. While the cleaning cycle is important for

the descaling cycle is essential to ensure that
the machine is kept clean on the inside and
free from mineral build-up.It is recommended
REPLACING THE WATER FILTER
16
to descale your unit every 90 days when water
hardness is at level 4; and when water hardness
is at level 6, descale your unit every 60 days.
WARNING
Do not immerse power cord, power plug
or appliance in water or any other liquid.
The water tank should never be removed
or completely emptied during descaling.
NOTE
Do not use bottled water when descaling.
Most bottled water may contain dissolved solids
that can leave deposits inside the machine.
Priming machine for descaling function
1. Fully dissolve one sachet of Sage descaling

the water tank (start process after fully dissolving
the powder).
2. Press and hold the 2 CUP button and
then press and hold the POWER button
simultaneously to enter the Descale mode.
The unit will heat up as part of commencing
the descaling action, during the heating

continuously. The machine will indicate it is
ready for descaling when the POWER button,
1 CUP button, CLEAN ME indicator and HOT
WATER / STEAM indicator are all illuminated
(solid on).

3. Press the 1 CUP button to start the


takes approximately 25 seconds. The 1 CUP

constant once the descaling process has

25 seconds, press the 1 CUP button again.
Descale the steam and hot water
components
Descaling steam and hot water takes
approximately 13 seconds and 8 seconds
respectively. Descaling can be terminated
prematurely by turning the steam dial to STANDBY.
4. Descale Steam component by turning
the steam dial LEFT towards the STEAM icon.
5. Descale Hot water component by turning the
steam dial to the RIGHT towards the HOT
WATER icon.
Repeat processes to complete descaling
After the above processes about half
(0.5 litre) of the descale solution should
be left in the water tank.
6. Repeat steps 4-6 above to complete the
descaling process to empty the solution
in the tank.
Descaling Solution Rinse
7. After descaling, remove the water tank and

to the maximum capacity (2 litres) and repeat
steps 4-6 to further cleanse the machine of any
residue of the cleaning solution thoroughly.
8. Press ‘POWER’ to quit the descaling process.
This will be indicated by the LED lights

NOTE

is no action for 5 minutes in descaling mode.
To resume descaling, please start from step 3.
17
EN
ADVANCED CLEANING FOR THE CONICAL BURR GRINDER
Set ‘GRIND SIZEto ‘1’
(finest)
Use 10mm socket.
Rotate ‘Clockwise’ to loosen
the nut only
Set ‘GRIND SIZE’ to ‘16’
(coarsest)
Unlock & remove top burr Remove nut, spring & flat
washer. Carefully remove
lower burr
Remove hopper
1 2 3 4 6
Clean chute with brush Insert washers & grind fan
using long-nose pliers
Insert lower burr (drive pin
& cavity to align). Insert
flat washer & spring washer
Rotate ‘Counter-Clockwise’
to tighten nut
Unblock the grinds exit
chute using the brush
or a pipe cleaner
8 9 10 11 12
Insert & lock top burr
13
Set ‘GRIND SIZE’ to ‘5’.
Replace & lock hopper
14
SINGLE DOUBLE
PUSH TO GRIND
Remove grind fan & washers
using long-nose pliers
7
POWER FILTER SIZE
GRIND AMOUNT
GRIND SIZE
LOOSEN NUT
TIGHTEN NUT
GRIND SIZE SPRING
WASHER
FLAT
WASHER
GRIND SIZE
1. GRIND FAN
2. METAL WASHER
3. FELT WASHER
3
2
1
1.
FELT WASHER
2. METAL WASHER
3.
GRIND FAN
1
2
3
SPRING
WASHER
FLAT
WASHER
5
WARNING
Care should be taken as the grinder burrs
are extremely sharp.
This step is only required if there is a blockage between the grinding burrs and the grinder outlet.
CLEANING THE STEAM WAND
The steam wand should always be cleaned after
texturing milk. Wipe the steam wand with a damp
cloth. Then with the steam wand tip directed over

dial to the STEAM position. This will clear any
remaining milk from inside the steam wand.
If any of the holes in the tip of the steam wand
become blocked, ensure the STEAM / HOT
WATER dial is in the STANDBY position. Press

and allow to cool. Use the pin on the end of the
provided cleaning tool to unblock the hole(s).
If the steam wand remains blocked, remove the
tip using the integrated spanner in the cleaning
tool and soak in hot water. Use the pin on the end
of the provided cleaning tool to unblock the hole(s)
before re-attaching to the steam wand.
CLEANING THE FILTER BASKETS
AND PORTAFILTER

under hot water immediately after use to remove


blocked, use the pin on the end of the provided
cleaning tool to unblock the hole(s).
If the hole(s) remain blocked, dissolve a cleaning


Rinse thoroughly.
CLEANING THE SHOWER SCREEN
The group head interior and shower screen
should be wiped with a damp cloth to remove any

Periodically purge the machine. Place an empty

Press and hold the 1 CUP button and run a short

CLEANING THE DRIP &
STORAGE TRAY
The drip tray should be removed, emptied and
cleaned at regular intervals, particularly when the
drip tray full indicator is showing EMPTY ME!


grounds. The EMPTY ME! indicator can also be
removed from the drip tray by pulling upwards
to release the side latches. Wash all parts in
warm soapy water with a soft cloth. Rinse and
dry thoroughly.
18
The storage tray (located behind the drip tray)
can be removed and cleaned with a soft, damp
cloth. Do not use abrasive cleansers, pads
or cloths which can scratch the surface.
NOTE
All parts should be cleaned by hand using warm
water and a gentle dish washing liquid. Do not
use abrasive cleansers, pads or cloths which
can scratch the surface. Do not clean any of the
parts or accessories in the dishwasher.
CLEANING THE OUTER HOUSING
& CUP WARMING TRAY
The outer housing and cup warming tray can
be cleaned with a soft, damp cloth. Polish with
a soft, dry cloth. Do not use abrasive cleansers,
pads or cloths which can scratch the surface.
STORING YOUR MACHINE
Before storing, ensure the STEAM / HOT
WATER dial is in the STANDBY position,
press the POWER button to switch the machine

Remove unused beans from the hopper,
clean the grinder (see page 17), empty
the water tank and the drip tray.
USING THE ALLEN KEY
Over time, the silicone seal surrounding
the shower screen will need to be replaced
to ensure optimum brewing performance.
1. Press the POWER button to switch the

power outlet.
2. Carefully remove the water tank and drip tray,
taking particular care if they are full.
3. Using a skewer or similar, clean the centre

4. Insert the shorter end of the Allen Key into
the centre of the screw. Turn counter-clockwise
to loosen the screw.
WARNING
Do not immerse power cord, power plug
or appliance in water or any other liquid.
5. Once loosened, carefully remove and retain
the screw, stainless steel shower screen.
Make note of the side of the shower screen
and dispersion plate that are facing downwards.
This will make re-assembly easier. Wash the
shower screen in warm soapy water, then dry
thoroughly.
6. 
or a pair of long-nose pliers. Insert the new seal,

7. Re-insert the shower screen, then the screw.

for 2-3 revolutions then insert the Allen Key

shower screen.
8. Re-insert the drip tray and water tank.
Contact Sage Customer Service or visit
sageappliances.com for replacement
silicone seals or for advice.
Clean centre of screw

19
EN
PROBLEM POSSIBLE CAUSE WHAT TO DO
Machine does
not heat up.
STEAM/HOT
WATER light

the machine
is turned on.
STEAM / HOT WATER dial is not in
the STANDBY position. Turn the STEAM / HOT WATER dial to the STANDBY
position. Machine will commence heating.
Water does

from the
group head.
No hot water.
Machine has not reached operating
temperature. Allow time for the machine to reach operating

and all button lights on the control panel
will illuminate when ready.
Water tank is empty. Fill tank.
Water tank is not fully inserted
and locked into position. Push water tank down completely to lock into place.
Machine needs to be descaled. Refer to ‘Descaling’, page 15.



is blocked.

spouts or not at all’.
Espresso only
drips from

spouts or
not at all.
 Use slightly coarser grind. Refer to ‘Setting the
Grind Size’, page 9 and ‘Over Extraction’, page 11.
 
Amount’, page 9 and ‘Over Extraction’, page 11.
 Tamp between 1015kg of pressure.
Water tank is empty. Fill tank.
Water tank is not fully inserted and
locked into position. Push water tank down completely to lock into place.
 Use the pin on the end of the provided cleaning tool
to unblock the hole(s). If the hole(s) remain blocked,


20 minutes. Rinse thoroughly.
Machine needs to be descaled. Refer to ‘Descaling’, page 15.
Espresso
runs out too
quickly.
 
page 9 and ‘Under Extraction’, page 11.

basket. 
Amount’, page 9 and ‘Under Extraction’, page 11.
 Tamp between 10-15 kg of pressure.

the Dosing Funnel 54
EUK
20
PROBLEM POSSIBLE CAUSE WHAT TO DO
Espresso runs
out around the
edge of the


in the group head correctly. 
until resistance is felt.

grounds around the


to ensure a proper seal in group head.
 Tamp between 10-15kg of pressure.
 
Amount’, page 9.
The silicone seal surrounding the
shower screen needs to be replaced

secured into the group head.
Refer to ‘Using the Allen Key’, page 18.
No steam. Machine has not reached operating
temperature. Allow time for the machine to reach operating
temperature. The STEAM / HOT WATER light will

steam. During this time, condensed water may purge
from the steam wand. This is normal. When the

wand is ready for use.
Water tank is empty. Fill tank.
Water tank is not fully inserted
and locked into position. Push water tank down completely to lock into place.
Machine needs to be descaled. Refer to ‘Descaling’, page 15.
Steam wand is blocked. Refer to ‘Cleaning the Steam Wand’, page 17.
STEAM/HOT WATER dial is not
in the STEAM position. Ensure the STEAM / HOT WATER dial is completely
rotated to the STEAM position.

hot enough. Cups not pre-heated. Rinse cups under hot water outlet and place
on cup warming tray.
 
Dry thoroughly.
Milk not hot enough
(if making a cappuccino or latté etc). Heat milk until side of the jug becomes hot to touch.
Machine needs to be descaled. Refer to ‘Descaling’, page 15.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200

Sage SES875 the Barista Express Manuel utilisateur

Catégorie
Cafetières
Taper
Manuel utilisateur