Matrox Millennium P750 Manuel utilisateur

1

User Guide

10818-301-0200

2003.04.30

Matrox Parhelia

Matrox Millennium P750

Matrox Millennium P650

ENGLISH

2 Matrox graphics card – User Guide

Hardware installation

This section describes how to install your Matrox card. If your Matrox graphics card is already

installed in your computer, skip to “Connection setup”, page 4. For information specific to your

computer, like how to remove its cover, see your system manual.

1 Open your computer and

remove your existing graphics

card

*

Turn off your computer and all peripherals

such as your monitor or printer. Open the

computer and remove your existing

graphics card (if any). (If graphics hardware

is built into the motherboard of your

computer, this graphics hardware should

automatically disable itself after your

Matrox card is installed.)

2 Locate the AGP slot in your

computer

Most computers have different types of

expansion slots. Your Matrox graphics card

is an AGP card. Locate the AGP slot in your

computer. Your system manual should

identify the location of each type of

expansion slot in your computer.

WA RNIN G :

To avoid personal injury, turn off your computer, unplug it, and then wait for

it to cool before you touch any of its internal parts. Also, static electricity can severely

damage electronic parts. Before touching any electronic parts, drain static electricity from

your body (for example, by touching the metal frame of your computer). When handling

a card, carefully hold it by its edges and avoid touching its circuitry.

* With multi-display mode, you may be able to use your existing graphics card. For more information, see Windows online help

under “Multiple Display Support”.

AGP slot

PCI slot (64-bit)

ISA slot

(Back of computer)

PCI slot (32-bit)

Matrox graphics card – User Guide 3

3 Insert your Matrox card

a

Remove the cover for the slot you intend

to use.

b

Save the screw for the mounting

bracket. Position your Matrox card over

the expansion slot you’ve chosen.

c

Push the card in firmly and evenly until

it’s fully seated in the slot.

d

Replace the screw to secure the bracket

of your Matrox card to the computer

frame.

Your Matrox card is now installed.

Before restarting your computer,

connect your monitor or

monitors (see “Connection setup”, page 4).

After connecting,

restart your computer and install your

Matrox software (see “Software setup”, page 7).

WA R N I N G :

Inserting your Matrox card

into the wrong type of slot could damage

your card, your computer, or both.

PCI card

32-bit

64-bit

AGP card

WA R N I N G :

If your computer doesn’t restart after your graphics card is installed, turn off

your computer to avoid damaging electronic parts. For troubleshooting information, see

page 9.

4 Matrox graphics card – User Guide

Connection setup

This section describes how to connect your monitors to your Matrox graphics card.

Connector overview

*

* Matrox Millennium P650 products include 2 DVI-to-HD15 adapters, but no dual-monitor cable or TV output adapter.

Note:

To c o n n e c t a

digital

monitor (a

monitor that uses digital input, usually a

flat panel monitor) to your Matrox

product, your monitor must have a DVI

connector.

If you have an

analog

monitor (a monitor

that uses analog input) with a DVI

connector and you want to connect it to

an HD-15 connector, you’ll need a separate adapter. If this adapter isn’t included with your

monitor, contact your monitor vendor.

Some monitors with DVI connectors support both digital and analog input. If you’re using

one of these monitors with your Matrox product, make sure it’s configured to use the

correct type of input. For more information, see your monitor documentation.

TV output adapter

*

Dual-monitor cable

*

Secondary (

B

) connector (DVI)

Main (

A

)

connector

(DVI)

DVI-to-HD15

adapter

*

HD-15 connector

(

1

)

HD-15 connector

(

2

)

Composite video

connector

S-video connector

DVI connector

(digital)

HD-15 connector (analog)

DVI connector

(analog/digital)

Matrox graphics card – User Guide 5

Step-by-step connection setup

1 Connect the first monitor

Connect your preferred monitor to the main

connector (

A

) on your Matrox graphics

card.

If your monitor has a DVI connector,

connect it directly to the main connector of

your graphics card.

If your monitor has an HD-15 connector,

use the DVI-to-HD15 adapter included with

your Matrox product to connect your

monitor to the main connector.

2 Connect the second monitor

If your second monitor uses a DVI

connector, connect it directly to the

secondary connector (

B

) of your graphics

card.

If your second monitor uses an HD-15

connector, you can use a dual-monitor cable

(included with certain Matrox products) or

a DVI-to-HD15 adapter. To use 3 monitors

at a time, a dual-monitor cable is required.

WA R N I N G :

Don’t change monitor connections while your computer is turned on. While

your computer is turned on, it may be using monitor settings that are specific to the current

monitor connections.

Some

devices may be permanently damaged if incorrect settings are

used.

Note:

If you want to use 3 monitors at a

time and one of these needs to use a DVI

connector, that monitor must be

connected to the main connector.

DVI connector

HD-15 connector

DVI connector

6 Matrox graphics card – User Guide

If you use a dual-monitor cable, connect it

to the secondary connector on your graphics

card, then connect your monitor to

connector

1

on the dual-monitor cable. If

you’re going to connect the TV output

adapter, connect your computer monitor to

connector

2

instead.

3 Connect the third monitor

If you want to use 3 computer monitors at a

time and your Matrox product supports it,

your second and third monitors must use

HD-15 connectors. Connect your third

monitor to connector

2

on the dual-monitor

cable.

HD-15

connector

Note:

The left-to-right order of your displays isn’t dependent on your connection setup

and, through Matrox PowerDesk software, you can re-order your displays to match your

Windows desktop. For more information, see Matrox PowerDesk help.

Note:

Whenever you change your connection setup, make sure you’re using the correct

connectors and that all connectors are properly fastened.

Whenever you restart your computer, make sure your monitors are already turned on.

Otherwise, the software may not be able to properly detect your monitors.

Note:

To connect a TV or video recorder to your

graphics card, you need a TV output adapter

(included with certain Matrox products). The TV

output adapter connects to connector

1

on your

dual-monitor cable or to a DVI-to-HD15 adapter.

For more information, see “TV output” in the

online version of this guide.

HD-15

connector

VIDEO OUT

S-VIDEO OUT

TV output adapter

Matrox graphics card – User Guide 7

Software setup

This section describes how to install Matrox software for

Windows

2000/XP

. (For other operating systems, see the

Readme

file in the root

folder of the Matrox installation CD-ROM.)

You may need administrator rights to install certain software. For

more information, see Windows documentation.

1 Install display driver

Windows detects new hardware when you restart. If Matrox display drivers haven’t been

previously installed, Windows prompts you to install a display driver. Follow the on-screen

instructions. (The Matrox Windows 2000/XP display driver is in the

Win2kXP

folder of your

Matrox installation CD-ROM.)

2 Install optional software

After your computer restarts, the setup program shows you a list of additional items you can

install. Follow the on-screen instructions.

3 Configure your monitor settings

To take full advantage of your graphics card, make sure you have the correct monitor settings

selected in Windows for

each

of your monitors:

a

Right-click your Windows desktop background, then click

Properties

!

Settings

!

Advanced

!

Monitor

. If you’re using a multi-display desktop, select a display before

clicking

Advanced

.

b

If “

Hide modes that this monitor cannot display

” is available, make sure it’s enabled.

Under

Screen refresh rate

, select the highest refresh rate listed.

c

Click

OK

!

OK.

For more information on Windows monitor settings, see Windows documentation.

WA R N I N G :

If incorrect software monitor settings are applied,

some

monitors can be

permanently damaged. For more information, see your monitor manual.

8 Matrox graphics card – User Guide

4 Set up your display software

Use Matrox PowerDesk software to change certain display settings or access Matrox features.

To access PowerDesk, double-click its icon ( ) on your Windows taskbar. To see the

PowerDesk icon in Windows XP, you may need to click the

Show hidden icons

button ( )

on your Windows taskbar. For more information on how to use Matrox PowerDesk, see the

online help.

Matrox graphics card – User Guide 9

Troubleshooting

Basic procedures

This section explains basic procedures that are referred to by some troubleshooting items in this

guide.

Restarting in VGA mode

Windows 2000/XP –

What follows is information on how to restart your computer in

VGA mode

.

If your primary display is

usable

:

1

Restart your computer, click

Start

!

Shut Down

!

Restart

!

OK

.

2

Before

Windows starts, press [F8] for the Windows startup menu to appear. (If [F8]

doesn’t work, instead try pressing and holding [Ctrl] before Windows starts.)

3

Select “VGA mode”, then press [Enter].

If your primary display is

unusable

:

1

Restart your computer. For more information, see your system manual.

2

Before

Windows starts, press [F8] for the Windows startup menu to appear.

3

Select “VGA mode”, then press [Enter].

Main troubleshooting

This section addresses possible problems that could prevent you from using your computer.

Problem Computer doesn’t display information or boot after Matrox card is

installed

1

Cause

Your Matrox card may not be properly installed.

1

Solution

Make sure your Matrox card is properly installed. Specifically, make sure the card is firmly

inserted in its expansion slot and that all connections to it are firmly in place. For more

information, see “Hardware installation”, page 2.

2

Cause

There may be unsupported graphics hardware in your computer.

1

Solution

If an unsupported graphics card is plugged into an expansion slot, remove it.

10 Matrox graphics card – User Guide

2

Solution

If a graphics adapter is built into your computer motherboard, your system may not have

automatically disabled it when you inserted your Matrox card. Check your system manual for

instructions on how to disable your computer’s built-in graphics adapter.

3

Cause

Your computer BIOS (Basic Input/Output System) settings may be incorrect.

1

Solution

Change your BIOS settings, specifically the

AGP aperture size

. For more information on your

computer BIOS, see your system manual.

4

Cause

Your computer BIOS may not be up to date. For more information on your computer BIOS,

see your system manual.

1

Solution

Reinstall your previous graphics card and, if possible, update your computer BIOS. This can

usually be done with software from the manufacturer of your computer. Contact your system

vendor or manufacturer to get a BIOS update for your computer.

To get the correct BIOS update, you may need to know the serial number your computer

displays when it restarts. (This number is usually in the lower-left corner of the display.)

5

Cause

The BIOS of your Matrox graphics card may need to be updated or restored.

1

Solution

For advanced users –

If you have another VGA-compatible graphics card (ISA or PCI), you

can try resetting the BIOS of your Matrox graphics card.

1

Turn off your computer and insert the other graphics card into an expansion slot. For

more information on expansion slots, see “Locate the AGP slot in your computer”, page

2.

2

Plug your monitor into the other graphics card and restart your computer.

3

Insert your Matrox installation CD-ROM.

4

Click

Start

!

Run

, type

d:\SysUtils

. You will need to use the

PBIOSWin

program to

update the BIOS of your Matrox graphics card. For more information on how to use this

program, see the

Readme

file in the

Sysutils

folder.

Note:

Make sure your computer uses the other graphics card to control your primary

display. The graphics card that controls your primary display is the one that first

displays information when you restart your computer.

Your computer BIOS (Basic Input/Output System) and the slot type (ISA, PCI, or AGP

– see “Locate the AGP slot in your computer”, page 2) of each graphics card help

determine which graphics card controls your primary display.

To control which graphics card is used for your primary display, you may be able to

change the configuration of your computer BIOS. For information on how to change

your computer BIOS settings, see your system manual.

Matrox graphics card – User Guide 11

5

Turn off your computer, remove the other graphics card, then plug your monitor into

your Matrox graphics card.

6

Restart your computer.

6

Cause

The power supply of your computer may not be powerful enough for all the devices on your

computer.

1

Solution

For advanced users –

Remove unnecessary devices from your computer (for example, an

unused network card or an extra CD-ROM drive). For more information, see your system

manual or the documentation for each device.

2

Solution

You may be able to upgrade the power supply of your computer. We recommend a power

supply of 300 Watts or more. For more information, contact your computer vendor.

Problem Wrong color balance, screen image off-center, or no picture at all

1

Cause

Your monitor video controls may be improperly set.

1

Solution

Adjust your monitor controls (brightness, contrast, and so on). For more information, see

your monitor manual.

2

Cause

Your monitor may not be properly connected.

1

Solution

Make sure you’re using the correct connectors (see “Connection setup”, page 4) and that all

connectors are properly fastened.

2

Solution

Make sure the monitor power cable is firmly in place.

3

Solution

Make sure the connection to the back of the monitor is firmly in place.

If your monitor uses BNC input, make

sure the Red (

R

), Green (

G

), Blue (

B

),

Horizontal Sync (

HSYNC

– white or gray

wire), and Vertical Sync (

VSYNC

– black

wire) connections are firmly in place and

plugged into the correct input.

3

Cause

If your monitor uses BNC input, one or more connection settings may be incorrect.

1

Solution

Set each of your monitor RGB input and sync switches (if available) to 75 ohms, with the

sync set to “external”. These controls are usually switches on the back of your monitor.

4

Cause

If display problems occur after the startup screen of your operating system, your software

monitor settings may be incorrect.

Bayonet Nut Connect (BNC)

12 Matrox graphics card – User Guide

1

Solution

Make sure correct software monitor settings are selected.

If your primary display is still usable, see “Configure your monitor settings”, page 7.

Otherwise, see the next troubleshooting item.

2

Solution

Windows 2000/XP –

Make sure you’re not using inappropriate monitor settings

customizations:

1

Double-click the PowerDesk icon ( ) on your Windows taskbar to access the

PowerDesk main interface. To see the PowerDesk icon in Windows XP, you may need to

click the

Show hidden icons

button ( ) on your Windows taskbar.

2

Click

Monitor and TV Adjustments

.

3

Select the appropriate device.

4

Click

Adjust visible area and refresh rate

!

Reset

.

Problem After the startup screen, or after display settings are changed,

the screen image is garbled or unusable

(blank screen, rolling or overlapping screen images)

1

Cause

The Matrox display driver may be trying to use settings your monitor doesn’t support. This

can happen if a monitor was never selected in the software and the display resolution was

changed to one your monitor doesn’t support, or if the monitor connected to your computer

was changed without changing it in the software.

1

Solution

Windows 2000/XP –

1

If your primary display is unusable, restart your computer in VGA mode (see “Restarting

in VGA mode”, page 9).

2

Right-click the Windows desktop background, then click

Properties

!

Settings

.

3

Move the

Screen area

(Windows 2000) or

Screen Resolution

(Windows XP) slider

down to its lowest setting, then click

OK

.

4

Restart your computer normally.

5

Make sure the correct monitor is selected in Windows (see “Configure your monitor

settings”, page 7).

6

Restore your original display settings (see steps 2 and 3).

WA R N I N G :

If incorrect software monitor settings are applied,

some

monitors can be

permanently damaged. For more information, see your monitor manual.

Matrox graphics card – User Guide 13

2

Cause

Files on your system may have been deleted or corrupted.

1

Solution

Remove, then restore Matrox software:

Windows 2000/XP –

1

If your primary display is unusable, restart your computer in VGA mode (see “Restarting

in VGA mode”, page 9).

2

To remove Matrox software, click

Start

!

Settings

*

!

Control Panel

!

Add/Remove

Programs

(double-click*)

!

Matrox PowerDesk-HF and Driver

!

Change/Remove

!

Yes

. (* Depending on your version and configuration of Windows, this part of the step

may not be necessary.)

3

After removing Matrox software, install the latest display driver for your Matrox graphics

card. You may also need to reinstall other Matrox software.

More Information

We provide additional information in help files and in the online version of this guide. This guide is

available on your installation CD-ROM as an Adobe Acrobat file (

Guide\Guide.pdf)

. To view or print

PDF files, use the

Acrobat Reader

program, which you can install from the Matrox installation

CD-ROM.

Note:

Before removing software, make sure you have all the necessary files to reinstall

software that may still be needed.

Note:

Windows 2000/XP –

You may need administrator rights to remove certain software.

For more information, see Windows documentation.

Note:

Be sure to check for any last-minute release notes at the end of this manual and in

the Matrox CD-ROM

Readme

file. Also, check the Matrox Web site

(www.matrox.com/mga

) for the latest Matrox software, technical support, and product

information.

14 Matrox graphics card – User Guide

TV output

You can use the TV output adapter to connect a

video recorder or a TV to your Matrox graphics

card. This adapter is only included with certain

Matrox products. This section describes how to use

the

TV output

feature.

Connection setup

1 Turn off computer

Windows 2000/XP –

To shut down your computer, click

Start

!

Shut Down

!

Shut down

!

OK

, then turn off your computer.

2 Attach TV adapter

Connect the TV output adapter to

connector

1

on your dual-monitor cable.

If you’re only using one computer

monitor and a TV, you can use a DVI-to-

HD15 adapter to connect the TV output

adapter to the secondary (

B

) connector

on your Matrox card.

Note:

TV output isn’t supported with full-screen DOS display modes (for example, the

information you see before Windows starts) or with standard VGA mode (for example,

when you restart Windows in “safe mode”). Older programs may use these display modes.

While one of these display modes is in use, your TV displays nothing (black).

VIDEO OUT

S-VIDEO OUT

TV output adapter

WA R N I N G :

Don’t change monitor connections while your computer is turned on. While

your computer is turned on, it may be using monitor settings that are specific to the current

monitor connections.

If a display device (monitor, TV, or video recorder) is connected while your computer is

using settings intended for another display device, the display of the new device may be

garbled or unusable.

Some

devices may be permanently damaged if incorrect settings are

used.

TV output

adapter

Matrox graphics card – User Guide 15

3 Connect video output

To connect to a TV or a video recorder,

you’ll need a composite video (RCA) or

S-video cable.

If your video device (a TV or a video

recorder) didn’t come with one of these

cables, these types of cable are available at

most electronics stores. The type of cable

you use depends on what your video device

supports. Many video devices support

composite video connections, and some

higher-quality video devices support

S-video connections.

a

Attach one end of your composite

video or S-video cable to the

appropriate connector on your TV

adapter.

b

Attach the other end to the

VIDEO IN

*

connector on your TV

†

or video

recorder.

c

Before viewing or recording video

output directly from your computer,

make sure your TV or video recorder is

set up to use

line

input. For example, if

your TV has a

TV/VIDEO

switch, set it

to

VIDEO

; or if your video recorder has

a

TUNER/LINE

switch, set it to

LINE

.

Optionally, if you use the composite video

and

S-video connectors on your Matrox TV

adapter, you can directly connect two different video devices at the same time.

To v i e w

and

record output from the same Matrox video connector, you can connect it to a

video recorder and connect the video recorder to a TV. For more information, see your video

recorder and TV manuals.

* The labels on your devices may not be consistent with what’s in this guide. Different manufacturers sometimes use different labels

for the same type of controls and connectors. For example, the

VIDEO IN

connector on your TV may be labeled

VIDEO 1

(or

VIDEO

2

). To match labels, see the documentation for your video devices.

† If your TV only has an antenna or cable TV connector, you can use an

RF modulator

to connect it to your Matrox card. RF

modulators are available at most electronics stores.

TV or video recorder

using S-video

Composite

video (RCA)

cable

S-video cable

TV or video recorder

using composite video

TV adapter

(Note: Using the Matrox composite

video and S-video connectors at the

same time is optional.)

16 Matrox graphics card – User Guide

4 Connect audio output

Typically, the sound output from a

computer comes from speakers connected to

your sound card. If you prefer, you can hear

or record the sound output from your

computer using the same TV or video

recorder you connect to your graphics card.

To do this, you need an audio cable with a

stereo jack on one end and two RCA

connectors on the other end. If you don’t

have this type of cable, you can buy one at

most consumer electronics stores.

a

Plug the stereo-jack end of the audio

cable into the

LINE OUT

*

()

connector on your sound card.

b

Plug the other end of the cable into the

left (

L

) and right (

R

)

AUDIO IN

connectors of your video device. For

more information, see your sound card

manual.

Software setup

If a TV or video recorder is connected to your Matrox product, you can use TV output mode to view

or record your display on your TV or video recorder. (To connect video devices to your computer, see

page 14.)

TV settings have lower resolutions and refresh rates than typical computer monitor settings. Lower

refresh rates may result in more noticeable flicker.

* If your computer has no audio

LINE OUT

connector, you can use its

SPKR

(speaker) connector instead. In this case, all your

computer sound output goes to the video device you connected to.

TV or video

recorder

Sound

card

Note:

Two TV standards are supported for TV output. The NTSC standard is used in North

America and Japan, among other places. The PAL standard is used in most of Western

Europe and in China, among other places.

If an incorrect TV standard is selected in Matrox software, the output from your computer

may not appear or record properly on your TV or your video recorder. To find out what

standard your TV or video recorder supports, see its documentation.

Matrox graphics card – User Guide 17

Windows 2000/XP –

"

To add a TV to your Windows desktop or as a feature display, access

Multi-Display Setup

in your Matrox PowerDesk software.

"

You can also use a TV (or video recorder) as your secondary display:

#

With

Matrox Clone

– Access

Multi-Display Setup

in your Matrox PowerDesk

software and select

2 displays, Clone mode

.

#

With

Multi-display Zoom

– Access

Matrox Zoom

in your Matrox PowerDesk

software and select

Multi-Display Zoom

.

#

With

PureVideo/DVDMax

– Access

Video Playback Settings

in your Matrox

PowerDesk software and enable

Use PureVideo/DVDMax

.

"

To select the TV standard (NTSC or PAL) used for TV output:

1

Access

Monitor and TV Adjustments

in your Matrox PowerDesk software.

2

Click the TV in the left part of the page, then click

Select a TV output standard

.

3

Select

NTSC

or

PAL

according to the standard used by your TV or video recorder.

4

Click

OK

.

"

To adjust TV settings, access

Monitor and TV Adjustments

and

Video Playback Settings

in your Matrox PowerDesk software.

To access PowerDesk, double-click its icon ( ) on your Windows taskbar. To see the

PowerDesk icon in Windows XP, you may need to click the

Show hidden icons

button ( )

on your Windows taskbar. For more information on how to use Matrox PowerDesk, see the

online help.

18 Matrox graphics card – User Guide

Extra troubleshooting

Graphics

The following troubleshooting items address problems related to graphics cards.

Problem Can’t use Windows, Windows reports a configuration error, and/or

can’t install or uninstall Matrox display driver

1

Cause

The problem may be specific to the motherboard in your computer.

1

Solution

There may be a software update available for your motherboard. To find out what

motherboard model your computer is using, see your system manual. For more information,

contact the maker of your motherboard or computer. Many motherboard or computer

manufacturers have software updates available on their Web site.

2

Cause

Files on your system may have been deleted or corrupted.

1

Solution

Remove, then restore Matrox software. For more information, see page 13.

Problem Monitor settings aren’t automatically detected

Note:

Windows 2000/XP –

You may need administrator rights to install certain software.

For more information, see Windows documentation.

WA R N I N G :

If incorrect software monitor settings are used, your display may become

unusable and

some

monitors can be permanently damaged. For more information, see

your monitor manual.

Note:

Windows 2000/XP –

To check if your monitor settings are properly selected:

1

Right-click your Windows desktop background, then click

Properties

!

Settings

!

Advanced

!

Monitor

. If you’re using multiple displays in

independent

mode, select a

display before clicking

Advanced

.

2

If you see the name of your monitor or “Plug-and-Play”, your monitor settings are

properly selected.

If you see the wrong monitor name or

Default monitor

, your monitor settings aren’t

properly selected.

Matrox graphics card – User Guide 19

1

Cause

Your monitor may not be Plug-and-Play. Most new monitors are Plug-and-Play but many

older ones aren’t. Software can’t automatically detect settings for monitors that aren’t Plug-

and-Play.

1

Solution

Manually select your monitor settings in the software. For more information, see “Configure

your monitor settings”, page 7.

2

Cause

If a monitor was changed or added while Windows was running, the new monitor may not

be detected by the software.

1

Solution

Restart your computer. If your monitor is a Plug-and-Play (DDC) monitor, it should be

automatically detected by the software.

3

Cause

You may be using BNC connectors with a Plug-and-Play monitor. The Plug-and-Play feature

of a monitor can’t be used with BNC connectors.

1

Solution

If there’s an HD-15 connector at the back of your monitor, use this connector instead of the

BNC connectors.

Problem After game for Windows 2000/XP starts,

monitor doesn’t display properly

(blank screen, rolling or overlapping screen images)

1

Cause

If your game uses a low-resolution (640 × 480 and below), full-screen display mode, your

monitor may not support the refresh rate the Matrox driver is using.

1

Solution

1

If the game is still running in full-screen mode and your monitor is unusable, exit the

game. To do this, press [Alt]+[Tab]

once

, right-click the name of the game on the

Windows taskbar, then click

Close

.

2

Make sure the correct monitor is selected in Windows.

HD-15 connectorBNC (Bayonet Nut Connect)

connectors

20 Matrox graphics card – User Guide

Problem 3D and video programs don’t work

1

Cause

Your computer or program may not work well with bus mastering.

1

Solution

Disable bus mastering:

(If you want to continue using bus mastering, see the other solutions.)

Windows 2000/XP –

1

Double-click the PowerDesk icon ( ) on your Windows taskbar to access the

PowerDesk main interface. To see the PowerDesk icon in Windows XP, you may need to

click the

Show hidden icons

button ( ) on your Windows taskbar.

2

Click

Help

!

Troubleshooting settings

.

3

Make sure

Use bus mastering

is disabled.

4

Click

OK

or

Apply

. You can now close the PowerDesk main interface.

2

Cause

Your computer may not have given an interrupt request (IRQ) to your Matrox graphics card

or may have given one used by another device in your computer. This may be because your

computer’s “Plug-and-Play” feature is turned off.

Windows 2000/XP –

To check the display adapter’s IRQ:

1

Click

Start

!

Settings

*

!

Control Panel

!

Performance and Maintenance

*

!

System

(double-click*)

!

Hardware

!

Device Manager

. (* Depending on your version and

configuration of Windows, this part of the step may not be necessary.)

2

Click the plus sign to the left of the

Display adapters

. An “

X

” through an icon means the

hardware has been disabled. A circled exclamation point through the icon means the

hardware has a problem.

3

Double-click the name of your Matrox display

adapter to open a properties dialog box. The

type of problem is displayed in the

General

tab

!

Device status

area. Check also the

Resources

tab

!

Resource type

list for an

Interrupt Request

.

1

Solution

Change settings in your computer BIOS setup utility.

If your computer has the options of enabling Plug-and-Play detection, or assigning an IRQ

to a VGA adapter, make sure they’re enabled. If your computer doesn’t have these options,

you may be able to manually assign an IRQ to your graphics card using the BIOS setup utility.

For more information on the BIOS setup utility of your computer, see your system manual

or contact your system manufacturer.

La page est en cours de chargement...

Matrox Millennium P750 Manuel utilisateur

Ce manuel convient également à

Matrox Millennium P750 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents