OmniFilter OM36KCS Installation Instructions Manual

Marque: OmniFilter

Modèle: OM36KCS

Taper: Installation Instructions Manual

Ce manuel convient également à

OM26KCS, OM32KCS, OM36KCS

Water Softening System

INSTALLATION INSTRUCTIONS

English . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pages 2-22

Repair Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 13

OM26KCS, OM32KCS, OM36KCS

Sistema de ablandamiento de agua

INSTRUCCIONES DE INSTALACIÓN

Español . . . . . . . . . . . . . . . . . . . . . . . . . . Páginas 23-43

Piezas de repuesto . . . . . . . . . . . . . . . . . . . . . Página 32

OM26KCS, OM32KCS, OM36KCS

Système d'adoucissement d'eau

DIRECTIVES D'INSTALLATION

Français . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pages 44-64

Piéces de Rechange . . . . . . . . . . . . . . . . . . . . . Page 50

293 Wright Street • Delavan, WI 53115

Phone: 800.937.6664

www.omnilter.com

Tools and Fittings Required

• Pipe Cutter

• Tubing Cutter

• File

• Pliers

• Tape Measure

• Soldering Tools

• Lead Free Solder

• Bucket

• Towel

• Teon Pipe Tape

• Adjustable Wrench

• Tube 100% Silicone Grease

For further operating, installation, maintenance,

parts or assistance:

Call OMNIFILTER Customer Service at:

800.937.6664

Para obtener más información sobre el

funcionamiento, la instalación, el mantenimiento,

las piezas o para obtener asistencia:

Comuníquese con el Servicio de atención

al cliente de OMNIFILTER al: 800.937.6664

Pour de plus amples renseignements sur le

fonctionnement, l'installation, l'entretien, les

pièces, ou pour avoir de l'aide,

appelez le service clientèle OMNIFILTER à :

800.937.6664

Tested and Certied by WQA to

NSF/ANSI Standard 44 for softener

performance & 372 for "lead free"

compliance.

Herramientas y coples requeridos

• Cortadora de tubería

• Cortadora de tubos

• Lima

• Pinzas

• Cinta métrica

• Herramientas para soldar

• Soldadura sin plomo

• Cubeta

• Toalla

• Cinta de Teon (teón)

para tuberías

• Llave inglesa con pasador

ajustable

• Grasa 100 % siliconada

para tubos

Outils et accessoires requis

• Coupe-tuyau

• Coupe-tube

• Lime

• Pinces

• Mètre ruban

• Outils à souder

• Soudure sans plomb

• Seau

• Serviette

• Bande adhésive pour tuyau

en Teon

• Clé ajustable

• Graisse de silicone à 100 %

en tube

Testé et certié par WQA conforme à

la norme 44 pour la performance de

l'adoucisseur et à la norme 372 pour

conformité d'exemption de plomb de

NDF/ANSI.

Probado y certicado por WQA de

acuerdo con la Norma 44 de NSF/

ANSI con respecto al rendimiento

del ablandador y 372, en cuanto

al cumplimiento “sin plomo”.

TABLE OF CONTENTS

MANUAL OVERVIEW ............................................................2

INSPECTION ..........................................................................2

PARTS INCLUDED ................................................................2

EQUIPMENT INSTALLATION ................................................3

SYSTEM DISINFECTION ......................................................9

GENERAL 706 SERIES INSTRUCTIONS .............................10

DISPLAY ICONS 706 CONTROLLER ....................................10

KEYPAD - BUTTONS .............................................................11

RECHARGE ...........................................................................11

706 SERIES INITIAL POWER-UP..........................................13

INITIAL START-UP INSTRUCTIONS .....................................13

INSTALLATION CHECKLIST .................................................14

CARE AND USE OF YOUR BRINE TANK .............................14

PLACING SOFTENER INTO OPERATION ............................14

PLACING SOFTENER INTO OPERATION (TURNING ON

THE WATER) ..........................................................................15

TANK ASSEMBLY ..................................................................16

VALVE ASSEMBLY .................................................................17

BRINE WELL ASSEMBLY CH20795 ......................................18

TROUBLESHOOTING ...........................................................19

PENTAIR RESIDENTIAL FILTRATION, LLC LIMITED

WARRANTY ..........................................................................21

PERFORMANCE DATA SHEET .............................................22

MANUAL OVERVIEW

How To Use This Manual

This installation manual is designed to guide the installer

through the process of installing and starting softeners

featuring the 706 series controller.

This manual is a reference and will not include every system

installation situation. The person installing this equipment

should have:

• Knowledge in the 706 series controller and water softener

installation

• Knowledge of water conditioning and how to determine

proper control settings

• Basic plumbing skills

Icons That Appear In This Manual

WARNING:

Failure to follow this instruction can result in

personal injury or damage to the equipment.

NOTE: This will make the process easier if followed.

INSPECTION

Inspect the unit for damage or missing parts. Contact your

supplier if any discrepancies exist.

PARTS INCLUDED

The Water Softening System should have the following parts:

1. Softener Tank with Valve and Bypass

2. Connector Kit

3. Drain Line Flow Control and Drain Fitting

4. Drain Line Tubing (shipped inside the salt tank)

5. Tubing Clamp

6. Wall Transformer

7. Instruction Manual

NOTE: Do not return the

system to the store.

Before starting to assemble the system, check

that all the parts are present and not damaged.

The plumbing pieces needed to connect the

water system and softener salt are not included.

If any parts are missing or damaged, contact

OMNIFILTER Customer Service at: 800.937.6664.

Manual

2 • DE11 OM26KCS, OM32KCS, OM36KCS

EQUIPMENT INSTALLATION

General Warnings And Safety Information

Electrical

There are no user-serviceable parts in the AC adapter, motor,

or controller. In the event of a failure, these should be replaced.

• All electrical connections must be completed according to

local and national codes.

• Use only the power AC adapter that is supplied.

• The power outlet must be grounded.

• To disconnect power, unplug the AC adapter from its

power source.

Mechanical

• Do not use petroleum based lubricants such as vaseline,

oils, or hydrocarbon based lubricants. Use only 100%

silicone lubricants.

• All plastic connections should be hand tightened. Teon*

tape may be used on connections that do not use an

O-ring seal. Do not use pliers or pipe wrenches.

• All plumbing must be completed according to local, state

and international codes.

• Soldering near any plastic ttings should be done before

connecting ttings to the valve. Excessive heat will cause

interior damage to the valve.

• Observe drain line requirements.

• Do not use lead-based solder for sweat solder

connections.

• The drain line must be a minimum of 1/2-inch diameter.

Use 3/4-inch pipe if the backwash ow rate is greater than

7 gpm (26.5 Lpm) or the pipe length is greater than

20 feet (6 m).

• Do not support the weight of the system on the control

valve ttings, plumbing, or the bypass.

• It is not recommended to use sealants on the threads.

Use plumber tape on all threaded connections.

General

• Observe all warnings that appear in this manual.

• Keep the unit in the upright position. Do not turn on side,

upside down, or drop. Turning the tank upside down will

cause media to enter the valve.

• Operating ambient temperature is between 34°F (1°C)

and 120°F (49°C).

• Operating water temperature is between 35°F (1°F) and

100°F (38°C).

• Working water pressure range is 20 to 125 psi

(1.38 to 8.6 bar). In Canada the acceptable working water

pressure range is 20 to 100 psi (1.38 to 6.89 bar).

• Use only salt salts designed for water softening. Do not

use ice melting, block, or rock salts.

• Follow state and local codes for water testing. Do not

use water that is micro biologically unsafe or of unknown

quality.

• When lling media tank, do not open water valve

completely. Fill tank slowly to prevent media from exiting

the tank.

• When installing the bypass water connection, connect

to the plumbing system rst. Allow heated parts to cool

and cemented parts to set before installing any plastic

parts. Do not get primer or solvent on O-rings, nuts, or the

valve.

System Recharge Cycles (9-Cycle Operation)

Service (Downow):

Untreated water is directed down through the resin bed and up

through the riser tube. The hardness ions attach themselves

to the resin and are removed from the water. The water is

conditioned as it passes through the resin bed.

1. Brine Rell:

Water is directed to the salt tank at a controlled rate, to

create brine for the next recharge.

2. Brine Prep (Dissolve Salt)

After the rell cycle lls the salt tank with water, this cycle

allows time for the salt to dissolve into the water.

3. Backwash 1 (Upow):

The ow of water is reversed by the control valve and

directed down the riser tube and up through the resin bed.

During the backwash cycle, the bed is expanded and debris

is ushed to the drain.

4. Brine Draw (Downow):

The brine draw cycle takes place during the slow rinse

cycle. The control directs water through the brine injector

and brine is drawn from the salt tank. Brine draw is

completed when the air check in the salt tank closes.

5. Slow Rinse (Downow):

The brine is directed down through the resin bed and up

through the riser tube to the drain. The hardness ions are

displaced by sodium ions and are sent to the drain. The

resin is recharged during the brine cycle.

6. Repressurize Cycle (Hard Water Bypass Flapper Open):

This cycle closes the appers for a short time to allow the

air and water to hydraulically balance in the valve before

continuing the recharge.

7. Fast Rinse 1 (Downow):

The control directs water down through the resin bed and

up through the riser tube to the drain. Any remaining brine

residual is rinsed from the resin bed.

8. Backwash 2 (Upow):

The ow of water is reversed by the control valve and

directed down the riser tube and up through the resin bed.

During the backwash cycle, the bed is expanded and debris

is ushed to the drain.

9. Fast Rinse 2 (Downow):

The control directs water down through the resin bed and

up through the riser tube to the drain. Any remaining brine

residual is rinsed from the resin bed.

OM26KCS, OM32KCS, OM36KCS DE11 • 3

SERVICE

Cycle 2

BRINE PREP

To Regenerant

Tank

BRINE REFILL

Cycle 1

BACKWASH

Cycle 3

From Regenerant

Tank

BRINE/SLOW RINSE

Cycle 4 & 5

REPRESSURIZE

Cycle 6

FAST RINSE

Cycle 7

BACKWASH

Cycle 8

FAST RINSE

Cycle 9

Figure 1 Flow Patterns

System Features

Control

Inlet

Outlet

Drain Line

Salt

Compartment

Overow Line

Figure 2 Top of Unit

LCD

Display

Recharge

Button

Water Hardness

Button

Salt Amount

Button

Time of Day

Button

Figure 3 Control Front

Voltage

Adapter

Input

Main Motor and

Optical Sensor

Connection

Signal Input

Figure 4 Control Back

12.5

(318.5)

21.8

(554.2)

44.4

(1127.5)

37.9

(963.3)

3.0

(76.1)

Figure 5 Dimensions

EQUIPMENT INSTALLATION continued

4 • DE11 OM26KCS, OM32KCS, OM36KCS

System Specications

Item Number 4001557 4001558 4001559

Part Number OMNI OM26KCS OMNI OM32KCS OMNI OM36KCS

Recharge Style Meter - Demand Meter - Demand Meter - Demand

Media Tank Size 9" x 35" 10" x 35" 10" x 35"

Resin Volume 0.82 Cu Ft 1.00 Cu Ft 1.09 Cu Ft

Salt Storage 220 lbs 220 lbs 220 lbs

Drain Water Rate 2.7 GPM 3.9 GPM 3.9 GPM

Service Connection Size 1" NPT 1" NPT 1" NPT

Drain Connection Size 1/2" NPT 1/2" NPT 1/2" NPT

Recharge (brine) Connection Size 3/8" NPT 3/8" NPT 3/8" NPT

Installation Space Requirements 23" D x 13" W x 45" H 23" D x 13" W x 45" H 23" D x 13" W x 45" H

Shipping Weight 82 Lbs 93 Lbs 100 Lbs

EQUIPMENT INSTALLATION continued

• Temperature — Extreme hot or cold temperatures may

cause damage to the valve or controller.

Freezing temperatures will freeze the water in the valve.

This will cause physical damage to the internal parts as

well as the plumbing.

High temperatures will affect the controller. The display

may become unreadable but the controller should

continue to function. When the temperature drops down

into normal operating limits the display will return to

normal.

• Insects — The controller and valve have been designed

to keep all but the smallest insects out of the critical

areas. The top cover should be installed securely in

place.

Things You Need to Know

• When the controller is rst plugged in, it may display

an Err 3, this means that the controller is rotating the

camshaft to the home position.

• The preset default time of recharge is 2:00 AM.

• The controller is programmed to recharge if a recharge

has not taken place in the last 15 days. This setting

cannot be changed.

• Make sure control power source is plugged in. The

transformer should be connected to a non-switched

power source.

• Unless changed, the settings for a newly installed system

are:

Hardness - 25 grains per gallon

Salt Setting - HE (High Efciency)

Internal System clock starts at 0 hours (midnight)

The rst recharge will occur when the system clock

reaches 2:00 AM

• Test your water. Take a 4-5 oz sample of your water to

someone who can test for hardness. This information will

be used to setup the control.

Location Selection

Location of a water treatment system is important. The

following conditions are required:

• Level platform or oor.

• Room to access equipment for maintenance and adding

salt to tank.

• Ambient temperatures over 34°F (1°C) and below 120°F

(49°C).

• Water pressure below 125 psi (8.6 bar) and above

20 psi (1.4 bar).

• In Canada the water pressure must be below 100 psi

(6.89 bar).

• Constant electrical supply to operate the controller.

• Total minimum pipe run to water heater of ten feet (three

meters) to prevent backup of hot water into system.

• Local drain for discharge as close as possible.

• Water line connections with shutoff or bypass valves.

• Must meet any local, state and international codes for the

installation site.

• Valve is designed for minor plumbing misalignments. Do

not support weight of system on the plumbing.

• Be sure all soldered pipes are fully cooled before

attaching plastic valve to the plumbing.

Outdoor Locations

It is recommended that the OMNI system be installed indoors.

When the water conditioning system must be installed

outdoors, several items must be considered.

• Moisture — The valve and 706 controller are rated

for NEMA 3 locations. Falling water should not affect

performance.

The system is not designed to withstand extreme humidity

or water spray from below. Examples are: constant heavy

mist, near corrosive environment, upwards spray from

sprinkler.

• Direct Sunlight — The materials used will fade or discolor

over time in direct sunlight. The integrity of the materials

will not degrade to cause system failures.

OM26KCS, OM32KCS, OM36KCS DE11 • 5

EQUIPMENT INSTALLATION continued

Laundry Tubs

Pump

Meter

Hot Water

Outlet

Outside

Faucet

Outside

Faucet

Water

Heater

Bath Tub Lavatory Toilet Kitchen

Floor Drain

Figure 6 Standard Basement Before Installation. Cold Water Lines Shown

Soft Water

Hard Water

Outside

Faucet

Outside

Faucet

Bath Tub Lavatory Toilet Kitchen

Laundry Tubs

Pump

Meter

Hot Water

Outlet

Water

Heater

Brine Tank Overow Drain

Floor Drain

Drain Line

Bypass

Softener

Grounding

Strap

Figure 7 Softened Water Flow Diagram

6 • DE11 OM26KCS, OM32KCS, OM36KCS

EQUIPMENT INSTALLATION continued

Valve Layout

Outlet 1" NPT Inlet 1" NPT

Meter

Cable

Drain 1/2" NPT

To Brine Tank

3/8" NPT

Figure 8

Water Line Connection

A bypass valve system is included and will be installed on all

water conditioning systems. Bypass valves isolate the softener

from the water system and allow unconditioned water to be

used. Service or routine maintenance procedures may also

require that the system is bypassed.

IMPORTANT: The bypass valve is shipped to you in the

bypass position (Figure 9 Series 360 Bypass Operation).

When the valve is in bypass water will not enter the

softening tank. The water in the building will not be

treated. Figure 9 Series 360 Bypass Operation, shows the

handles in the service position.

Once you have selected your location check the direction of

the waterow in the main pipe. Figure 9 Series 360 Bypass

Operation can be used to plan the new plumbing assembly.

Inspect the main water pipe. Write down the type of pipe

(copper, plastic, galvanized etc.). Record the size of the pipe.

Plastic style pipes usually have the size printed on the outside.

Other pipes can be measured for the outside diameter and

converted into the pipe size at the store. Do not use pipe that is

smaller than the main water pipe.

The bypass requires two connector ttings that connect to the

plumbing. Size will be determined by the specic installation

requirements.

If the main plumbing is galvanized pipe and you are installing

copper pipe, then you must use dielectric insulating connectors

between the two styles of pipe.

Place the tank in position. The design of the tank does not

allow for bad alignment of the connections. You may ask your

supply store about exable connections.

Take measurements and create a drawing of your installation.

Include pipe lengths and elbows that are needed. If the water

ow is from right to left you will need to cross the plumbing to

the softener. Take the drawing to your plumbing supply store.

Consult with their expert for installation ideas and suggestions.

Assemble the plumbing.

WARNING:

If pipes will be sweat soldered, do not

connect adapters to the bypass until the

pipes have cooled.

IN OUT

Connector

Assembly

“H” Clip

Drain

Line

Handles in Service Handles in Bypass

Figure 9 Series 360 Bypass Operation

WARNING:

The inlet water must be connected to the

inlet port of the valve. When replacing

an exsisting system, it is possible that

the inlet and outlet plumbing is installed

in a reverse position. Be certain the inlet

connection on the valve is connected to the

incoming water tting from the water supply.

WARNING:

Do not use petroleum grease on gaskets

when connecting bypass plumbing. Use

only 100% silicone grease products when

installing any plastic valve. Non-silicone

grease may cause plastic components to fail

over time.

The bypass assembly connects to the water system by means

of a connector assembly. The connector is secured to the

plumbing and then inserted into the bypass. A clip is used to

hold it in place.

Figure 10 Connector Assembly

Before inserting the connector:

• Check that all O-rings are in place and not damaged.

• Lubricate O-rings and sliding surfaces with 100% silicone.

Firmly insert connector into bypass. Press locking clip into

position. Make certain the clip is fully engaged.

OM26KCS, OM32KCS, OM36KCS DE11 • 7

To remove a clip:

1. Turn off water and release water pressure at the valve.

2. Push the water line connectors into the bypass and valve.

This will help release O-rings that may have seated in

place.

3. Remove the clip by inserting a at blade under the top

center of the clip and lifting (prying up).

CAUTION

Do not use pliers to remove a clip. It is likely the

clip will break.

NOTE: Before turning on the water to the valve, rotate the

two handles on the bypass valve 2-3 times. This

will help seat O-rings and prevent leaking.

Drain Line Flow Control

The drain line ow control (DLFC) 1/2" NPT requires assembly

(Figure 11).

1. Locate parts and a roll of Teon tape (not included).

2. Wrap the tape over threads of the ow control.

3. Screw the ow control and a proper size drain tting

together. Hand tighten.

4. Place the ball into the ow control and insert the assembly

into the drain line opening.

5. Push the assembly in and secure with the drain line clip.

Drain Line

Fitting

Flow Control

Control Ball

Drain Line Clip

Figure 11

Drain Line Connection

NOTE: Standard commercial practices are expressed here.

Local codes may require changes to the following

suggestions. Check with local authorities before

installing a system.

1. The unit should be above and not more than 20 feet

(6.1 m) from the drain. Use an appropriate adapter tting

with a hose clamp to connect 1/2-inch (1.3 cm) plastic

tubing to the drain line connection of the control valve.

2. If the backwash ow rate exceeds 5 gpm (22.7 Lpm) or if

the unit is located 20-40 feet (6.1-12.2 m) from drain, use

3/4-inch (1.9 cm) tubing. Use appropriate ttings to connect

the 3/4-inch tubing to the 3/4-inch NPT drain connection on

the valve.

3. The drain line may be elevated up to 6 feet (1.8 m)

providing the run does not exceed 15 feet (4.6 m) and

water pressure at the softener is not less than 40 psi

(2.76 bar). Elevation can increase by 2 feet (61 cm) for

each additional 10 psi (.69 bar) of water pressure at the

drain connector.

4. Where the drain line is elevated but empties into a drain

below the level of the control valve, form a 7-inch (18-cm)

loop at the far end of the line so that the bottom of the loop

is level with the drain line connection. This will provide an

adequate siphon trap.

Where the drain empties into an overhead sewer line, a sink-

type trap must be used.

Secure the end of the drain line to prevent it from moving.

Right Way

Figure 12 Drain Line Connection

NOTE:

Waste connections or drain outlet shall be

designed and constructed to provide for

connection to the sanitary waste system through

an air-gap of 2 pipe diameters or

1 inch (22 mm) whichever is larger.

WARNING:

Never insert drain line directly into a

drain, sewer line, or trap (Figure 12 Drain

Line Connection). Always allow an air gap

between the drain line and the wastewater

to prevent the possibility of sewage being

back-siphoned into the softener.

Overow Line Connection

In the event of a malfunction, the salt TANK OVERFLOW will

direct “overow” to the drain instead of spilling on the oor. This

tting should be on the side of the cabinet.

Attach length of 1/2-inch (1.3-cm) I.D. tubing (not supplied) to

tting and run to drain. Do not elevate overow line higher than

overow tting (Figure 13 Overow Line Connection).

Do not tie into drain line of control unit. Overow line must be a

direct, separate line from overow tting to drain, sewer or tub.

Allow an air gap as per drain line instructions.

Figure 13 Overow Line Connection

EQUIPMENT INSTALLATION continued

8 • DE11 OM26KCS, OM32KCS, OM36KCS

EQUIPMENT INSTALLATION continued

Salt Line Connection

The salt line from the brine tube connects to the valve. Make

certain the connections are hand tightened. Be sure that the

salt line is secure and free from air leaks. Even a small leak

may cause the salt line to drain out, and the softener will not

draw salt from the tank. This may also introduce air into the

valve causing problems with valve operation.

Brine Tube

Salt Line Connection

Figure 14 Salt Tank Check Valve and Brine Well Assembly

Electrical Connection

CAUTION

This valve and control are for dry location use

only unless used with a Listed Class 2 power

supply suitable for outdoor use.

All 706 Series controllers operate on 12-volt alternating current

power supply. This requires use of the proper supplied AC

adapter included with your system.

AC Adapters:

Make sure power source matches the rating printed on the AC

adapter.

NOTE: The power source should be constant. Be certain

the AC adapter is not on a switched outlet. Power

interruptions longer than 8 hours may cause the

controller to lose the time setting. When power is

restored, the time setting must then be re-entered.

SYSTEM DISINFECTION

Disinfection Of Water Softeners

The materials of construction of the modern water softener

will not support bacterial growth, nor will these materials

contaminate a water supply. During normal use, a softener

may become fouled with organic matter, or in some cases with

bacteria from the water supply. This may result in an off-taste

or odor in the water.

Some softeners may need to be disinfected after installation

and some softeners will require periodic disinfection during

their normal life.

Depending upon the conditions of use, the style of softener, the

type of ion exchanger, and the disinfectant available, a choice

can be made among the following methods.

Sodium or Calcium Hypochlorite

Application

These materials are satisfactory for use with polystyrene

resins, synthetic gel zeolite, greensand and bentonites.

5.25% Sodium Hypochlorite

These solutions are available under trade names such as

Clorox*. If stronger solutions are used, such as those sold for

commercial laundries, adjust the dosage accordingly.

1. Dosage

A. Polystyrene resin; 1.2 uid ounce per cubic foot (35.5 ml

per 0.03 cubic meter).

B. Non-resinous exchangers; 0.8 uid ounce per cubic foot

(23.7 ml per 0.03 cubic meter).

2. Salt tank softeners

A. Backwash the softener and add the required amount of

hypochlorite solution to the well of the salt tank. The salt

tank should have water in it to permit the solution to be

carried into the softener.

B. Proceed with the normal recharge.

*Clorox is a trademark of the Clorox Company.

Calcium Hypochlorite

Calcium hypochlorite, 70% available chlorine, is available

in several forms including tablets and granules. These solid

materials may be used directly without dissolving before use.

1. Dosage

A. Two grains, approximately 0.1 ounce per cubic foot

(3 ml per 0.03 cubic meter).

2. Salt tank softeners

A. Backwash the softener and add the required amount

of hypochlorite to the well of the salt tank. The salt tank

should have water in it to permit the chlorine solution to

be carried into the softener.

B. Proceed with the normal recharge.

OM26KCS, OM32KCS, OM36KCS DE11 • 9

GENERAL 706 SERIES INSTRUCTIONS

706 Series Controller

Power Loss Memory Retention

The 706 Series controllers feature battery-free time and

date retention during the loss of power. This is designed to

last a minimum of 8 hours depending on the installation.

The controller will continue to keep time and day in dynamic

memory while there is no AC power.

The controller will not track water usage in the event of a

power failure.

All programmed parameters are stored in the 706 Series static

memory and will not be lost in the event of a power failure.

These settings are maintained separately from the time and

day settings.

Motor

The 706 series controller uses a standard 12-volt AC

50/60 Hz motor.

Power

706 Series controller is available in a 50/60 Hz power

conguration.

Information entered or calculated by the controller is stored in

two different ways.

1. A static memory will store:

User programmed values

Salt setting (salt setting)

Hardness setting

Daily averages (history values)

2. A dynamic memory with 8 hour retention will store:

Time of day

Todays water used

Variable Reserve Function

The 706 Series metered-demand volumetric controller is

designed to have a variable reserve feature. This feature

automatically adjusts the reserve to the end-user’s water

usage schedule.

A variable reserve saves salt and water by only regenerating

when absolutely necessary, and ensures enough soft water for

typical high-water usage days.

Each day the controller reviews the last four weeks of water

usage for the same day of the week to determine if the

remaining capacity is adequate for the next day of the week.

If the remaining capacity is not adequate, it will initiate an

automatic recharge.

NOTE: Water ow to the valve can be turned on or

bypassed when the controller is powered up for the

rst time.

DISPLAY ICONS 706 CONTROLLER

MIN

X100

6 7

Figure 15 Display Icons

NOTE: In normal operation and during programming, only

a few of the icons will actually be displayed.

1. Indicate water ow when displayed. Arrows alternate faster

as ow increases.

2. X100 multiplier for large values.

3. When “MIN” is displayed, the value is in minute increments.

“MIN” is displayed during recharge, the value displayed is

the minutes of recharge remaining.

4. Colon ashes as part of the time display. Indicates normal

operation.

5. Four digits used to display the time or program value. Also

used for error codes.

6. The recycle sign is displayed (ashing) when a recharge

at the next time of recharge has been called for. Also

displayed (continuous) when in recharge.

7. When “x2” is displayed, a second recharge has been called

for.

8. The hourglass is displayed when the motor is running.

NOTE: During normal operation (Service mode) the display

will show the current time of day with the colon

blinking. This will alternate with a display of the

gallons remaining to be treated before recharge.

10 • DE11 OM26KCS, OM32KCS, OM36KCS

KEYPAD - BUTTONS

Figure 16 Keypad Buttons

1. Time of Day - Press and release to display the time of day

for ve seconds. Press button again while current time is

displayed to increment the time 1 minute. Press and hold

for two seconds to rapidly increment the time.

2. Salt Amount - Press and release to display the current

salt setting for ve seconds. There are three salt settings;

HC (High Capacity), Sd (standard capacity) and HE (High

Efciency). Press the button again while the salt setting is

displayed to change the setting.

HC: This setting maximizes the system capacity between

recharges and will also use the most salt. This setting can

be used if you have high water hardness or high water

usage.

Sd: This setting uses moderate amount of salt and provides

a medium amount of water between recharges. This setting

can be used for moderate water hardness or water usage.

HE: This setting minimizes salt usage for a recharge (uses

the least amount of salt) and provides the least amount of

water between recharges. This setting can be used if you

have low water hardness or low water usage.

3. Water Hardness - Press and release to display the current

hardness setting for ve seconds. Press button again while

current setting is displayed to increment the hardness by

one. Press and hold for two seconds to rapidly increment

the hardness setting.

A hardness setting too high will cause the system to

recharge more often and use more salt and water than

what is needed to condition your water.

A hardness setting too low will cause the system to

recharge less often. The system may pass hard water

shortly before it recharges.

4. Recharge - Press and release to initiate a recharge. A

recharge will start at the next scheduled time of recharge. A

ashing regen symbol will be displayed. To stop a manual

recharge press and release the recharge button a second

time. To start an immediate recharge, press and hold the

recharge button for three seconds. A solid regen symbol will

be displayed. The time display will show the amount of time

left in the recharge cycle.

During a recharge cycle (the recharge icon is on steady), a

second manual (delayed) recharge may be called for. Press

the recharge button and release. To stop a second manual

recharge press and release the recharge button a second

time.

During a recharge cycle (the regen icon on steady), a

second manual (immediate) recharge may be called for.

Press the recharge button a second time for three seconds.

A second immediate recharge can not be stopped.

NOTE: If a button is not pushed for ve seconds, the

controller returns to normal operation mode.

Pushing the recharge button immediately returns

the controller to normal operation.

RECHARGE

During a Recharge:

• Total regen time remaining is displayed on screen.

• The recharge icon is on steady.

MIN

Recharge Total recharge time remaining

Flashes when motor is running

Figure 17 Display during recharge.

To Advance Recharge Cycles:

• Simultaneously press Time of Day and Recharge to

advance to the next cycle. An hourglass will display while

cam is advancing.

When cam reaches the next cycle, Time Remaining will

be displayed.

• Repeat pressing Time of Day and Recharge to advance

through each cycle.

• To determine which cycle the controller is in during a

recharge, use Table 2. The time remaining is displayed

on the controller. Find the time remaining below your salt

setting. The cycle column will have the cycle number.

• Press and hold Time of Day and Recharge for 3 seconds

to advance through all remaining recharge cycles.

Hourglass will ash.

Camshaft will advance to service - may take 1 to

2 minutes.

OM26KCS Recharge Cycles:

Table 1 Length of Cycle

Cycle Cycle Description HE Setting Sd Setting HC Setting

1 Rell 3 min 8.5 min 13 min

2 Brine Prep 120 min 120 min 120 min

3 Backwash 1 8 min 8 min 8 min

4* Brine Draw 6 min 18 min 28 min

5* Slow Rinse 37 min 37 min 37 min

6 Re-Pressurize 3 min 3 min 3 min

7 Fast Rinse 1 3 min 3 min 3 min

8 Backwash 2 1 min 1 min 1 min

9 Fast Rinse 2 1 min 1 min 1 min

Table 2 Time remaining to end of cycle

Cycle Cycle Description HE Setting Sd Setting HC Setting

1 Rell 184 min 201 min 216 min

2 Brine Prep 181 min 193 min 203 min

3 Backwash 1 61 min 73 min 83 min

4* Brine Draw 53 min 65 min 75 min

5* Slow Rinse 47 min 47 min 47 min

6 Re-Pressurize 10 min 10 min 10 min

7 Fast Rinse 1 7 min 7 min 7 min

8 Backwash 2 4 min 4 min 4 min

9 Fast Rinse 2 3 min 3 min 3 min

*The camshaft does not move between cycles 4 and 5. Cycle 5 begins

when the brine in the salt tank runs out and the check valve closes.

OM26KCS, OM32KCS, OM36KCS DE11 • 11

OM32KCS Recharge Cycles:

Table 1 Length of Cycle

Cycle Cycle Description HE Setting Sd Setting HC Setting

1 Rell 3.5 min 10.5 min 16 min

2 Brine Prep 120 min 120 min 120 min

3 Backwash 1 8 min 8 min 8 min

4* Brine Draw 6 min 19 min 30 min

5* Slow Rinse 35 min 35 min 35 min

6 Re-Pressurize 3 min 3 min 3 min

7 Fast Rinse 1 3 min 3 min 3 min

8 Backwash 2 1 min 1 min 1 min

9 Fast Rinse 2 1 min 1 min 1 min

Table 2 Time remaining to end of cycle

Cycle Cycle Description HE Setting Sd Setting HC Setting

1 Rell 182 min 202 min 219 min

2 Brine Prep 179 min 192 min 203 min

3 Backwash 1 59 min 72 min 83 min

4* Brine Draw 51 min 64 min 75 min

5* Slow Rinse 45 min 45 min 45 min

6 Re-Pressurize 10 min 10 min 10 min

7 Fast Rinse 1 7 min 7 min 7 min

8 Backwash 2 4 min 4 min 4 min

9 Fast Rinse 2 3 min 3 min 3 min

*The camshaft does not move between cycles 4 and 5. Cycle 5 begins

when the brine in the salt tank runs out and the check valve closes.

OM36KCS Recharge Cycles:

Table 1 Length of Cycle

Cycle Cycle Description HE Setting Sd Setting HC Setting

1 Rell 3.6 min 11 min 17.48 min

2 Brine Prep 120 min 120 min 120 min

3 Backwash 1 8 min 8 min 8 min

4* Brine Draw 7 min 18 min 23 min

5* Slow Rinse 36 min 36 min 36 min

6 Re-Pressurize 3 min 3 min 3 min

7 Fast Rinse 1 3 min 3 min 3 min

8 Backwash 2 1 min 1 min 1 min

9 Fast Rinse 2 1 min 1 min 1 min

Table 2 Time remaining to end of cycle

Cycle Cycle Description HE Setting Sd Setting HC Setting

1 Rell 183 min 203 min 214 min

2 Brine Prep 181 min 192 min 197 min

3 Backwash 1 61 min 72 min 77 min

4* Brine Draw 53 min 64 min 69 min

5* Slow Rinse 46 min 46 min 46 min

6 Re-Pressurize 10 min 10 min 10 min

7 Fast Rinse 1 7 min 7 min 7 min

8 Backwash 2 4 min 4 min 4 min

9 Fast Rinse 2 3 min 3 min 3 min

*The camshaft does not move between cycles 4 and 5. Cycle 5 begins

when the brine in the salt tank runs out and the check valve closes.

Recharge Cycle Requirements:

OM26KCS

HE Sd HC

Salt/Recharge

(lbs)

2.7 8.5 13.2

Regeneration

Time (Min)

62 82.5 96

Water to Drain

(gal)

37.5 43.2 46.6

Max. Flow to

Drain (gpm)

2.1 2.1 2.1

OM32KCS

HE Sd HC

Salt/Recharge

(lbs)

3.3 10.4 16

Regeneration

Time (Min)

60.5 80.5 97

Water to Drain

(gal)

47.4 51.8 57.1

Max. Flow to

Drain (gpm)

2.7 2.7 2.7

OM36KCS

HE Sd HC

Salt/Recharge

(lbs)

3.6 11.3 17.5

Regeneration

Time (Min)

63 85.5 100.5

Water to Drain

(gal)

48.2 55.4 59.7

Max. Flow to

Drain (gpm)

2.7 2.7 2.7

RECHARGE con tinued

12 • DE11 OM26KCS, OM32KCS, OM36KCS

706 SERIES INITIAL POWER-UP

The water supply valve should be off or the valve is in by-pass

Initial Power-Up - (Camshaft proceeds to in-service

position)

• At initial power-up, the camshaft may need to rotate to the

in-service position.

• Camshaft may take 1 to 2 minutes to return to in-service

position.

• Err 3 will be displayed until the camshaft returns to

in-service position (Figure 18 Initial Power-Up Display).

• If more than 2 minutes elapses, verify that the motor

is turning the camshaft. If it is not turning, check the

“Troubleshooting” section.

Figure 18 Initial Power-Up Display

When the camshaft has reached the in-service position the

display will show “- -:- -”.

If the time of day alternating with capacity remaining is

displayed then the controller has used short term memory

to load settings. Short term memory will hold settings for

approximately eight hours. Settings include:

• Water used today

• Water used since last recharge

• Current time of day

• Recharge state

Un-programmed controls will have the following settings.

Default settings:

• Hardness - 25 grains per gallon

• Salt setting - HE, High efciency

• System will recharge every 15 days (calendar override)

even if no water is used. Unplug system for long

periods of no water usage. Calendar override is not

programmable.

In addition:

• Water used is set to 0

• The internal system clock is set to 8:00 AM. The display

continues to show “- -:- -” until the time is manually set

which updates the internal clock.

• Day of the week is Sunday.

• A recharge will initiate when the internal system clock

reaches 12:00 am. The regen icon will ash.

INITIAL START-UP INSTRUCTIONS

1. Set time of day - Press the Time of Day button. Press it

again within 5 seconds and the time will increment. Press

and hold for 2 seconds to rapidly increment the setting.

Release the button and the time will be saved after

5 seconds.

Figure 19 Step 1

2. Pick the salt setting - The controller starts (defaults) with the

HE (high efciency) setting. If you want to check or change

the setting, press the Salt Amount button to display the

current setting. To change it, press the Salt Amount button

again within 5 seconds. The new setting will be saved after

5 seconds.

HC: This setting maximizes the system capacity between

recharges and will also use the most salt. This setting can be

used if you have high water hardness or high water usage.

Example: 3 or more people and/or hardness above 25 gpg.

Sd: This setting will provide a mid-range capacity. Less

salt is used than the HC (High Capacity), setting. More

water between recharges is provided than when the HE

(High Efciency) setting is used. Use this setting if the

conditioner is running out of capacity when set to HE. This

setting is also used if the HC setting is providing too much

capacity. Use this setting if your usage or water hardness

fall between the HC and HE examples.

HE: This setting minimizes salt used for a recharge (uses

the least amount of salt) and provides the least amount of

water between recharges. This setting can be used if you

have low water hardness or low water usage. Example: 2 or

less people and/or hardness below 20 grains per gallon.

Figure 20 Step 2

3. Enter the hardness of the water - The controller starts

(defaults) at a hardness of 25 gpg. Check your water for

the actual hardness. Press the Water Hardness button to

display the current settings. To change the setting press

the button again within 5 seconds. To rapidly increase the

setting push and hold the Water Hardness button. Release

the button and the setting will be saved after 5 seconds. A

hardness setting too high will cause the system to recharge

more often and use more salt and water than what is

needed to soften your water. A hardness setting too low will

cause the system to recharge less often. The system may

pass hard water shortly before it recharges.

Figure 21 Step 3

Programming is complete. The controller will begin normal

operation if no button is pushed for 5 seconds.

During normal operation (Service mode) the display will

show the current time of day with the colon blinking. This will

alternate with a display of the gallons remaining to be treated

before recharge.

OM26KCS, OM32KCS, OM36KCS DE11 • 13

INSTALLATION CHECKLIST

___ Read the owner's/installation manual?

___ Follow all safety guidelines in the manual?

___ If metal pipe was used, did you restore the electrical ground?

___ Securely install both drain hoses to an approved drain?

___ Perform a leak test?

___ Move the bypass valve to service?

___ Sanitize the softener?

___ Add salt pellets to the salt storage tank?

___ Program the control correctly to meet your needs?

___ Start a recharge?

CARE AND USE OF YOUR BRINE TANK

Each time the softener recharges, salty water (brine) is needed

to recondition the media in the water tank. The brine is pulled

from the salt tank at a controlled amount. If the salt tank does

not contain enough salt, the brine is weak, the media will not

fully recondition and untreated water will pass through.

You must keep salt in the tank.

The salt tank operates best when the salt level is below

half-full. If the tank is lled more than that the salt pellets may

"bridge". The salt pellets wedge against each other and do

not fall into the water at the bottom. Bridging will eventually

provide no salt to make brine. The softener will recharge but

not recondition the media. A salt bridge can be broken up using

a broom handle or similar rod. Carefully pound it into the salt

and the pellets will collapse. After loosening the salt pellets wait

2 hours and start a regeneration. A second recharge may be

needed to fully recondition the media.

You should only use sodium chloride pellet salt for water

softeners. Other types of salt (rock or snow melting) will

contain dirt and chemicals that will affect your water softener.

Keep the brine tank covered.

Empty and clean the tank every 3 years.

PLACING SOFTENER INTO OPERATION

After you have performed the previous initial power-up steps,

you will need to place the softener into operation. Follow these

steps carefully.

WARNING:

If the inlet water valve is opened too rapidly

or too far, media may be lost out of the tank

into the valve or the plumbing. In the 1/4

open position, you should hear air slowly

escaping from the valve drain line.

NOTE: We recommend that you do not put salt into the

tank until after the control valve has been put into

operation. With no salt in the tank, it is much easier

to view water ow and motion in the tank.

NOTE: As you advance through each cycle there will

be a slight delay before you can advance to the

next cycle. The hourglass icon will light while the

camshaft is indexing.

Press and hold the Recharge key to start a recharge.

To Advance Recharge Cycles:

• Simultaneously press Time of Day and Recharge to

advance to the next cycle. An hourglass will display while

cam is advancing.

When Cam reaches the next cycle, Time Remaining will

be displayed.

• Repeat pressing Time of Day and Recharge to advance

through each cycle.

• To determine which cycle the controller is in during a

recharge, use Table 1. The time remaining is displayed

on the controller. Find the time remaining below your salt

setting. The cycle column will have the cycle number.

• Press and hold Time of Day and Recharge for 3 seconds

to advance through all remaining recharge cycles.

Hourglass will ash.

Camshaft will advance to service - may take 1 to

2 minutes.

• For cycle times see Table 1.

Before turning on the water supply check the following:

• All plumbing is installed and secured.

• The valve drain line is in place and the end is held

securely at the drain.

• There is no salt in the tank.

• The controller is on and has been programmed following

the three steps. The display should be showing the time

of day with the colon ashing.

• The inlet water is off and the bypass is not in bypass

Both valve

handles pointing

in direction of

water flow

If any of the above are not true please correct the item before

proceeding further.

14 • DE11 OM26KCS, OM32KCS, OM36KCS

The following steps will describe how to perform a quick

recharge to verify the system is working correctly.

1. Turn the incoming water on at a low ow position. Listen

to the water ow. Water is entering the media tank. Do not

open the valve completely because media may enter the

valve.

2. Start a recharge.

3. Open a service faucet. The salt tank will begin to ll with

water. Air will come out of the faucet. After all of the air has

left the media tank the water will run without air spurts.

When the salt tank has 3 to 4 inches (7.6 or 10.1 cm) of

water, turn off the faucet and advance to the next cycle.

4. Turn inlet water on full.

5. The brine prep cycle allows the water in the salt tank to

dissolve the salt. During this cycle inspect for leaks. If

any leaks are present they should be repaired before

proceeding. If there are no leaks, advance to the next cycle.

6. Backwash forces water through the media to the drain.

Inspect the water for air bubbles and small particles. When

the water is running clear, advance to the next cycle.

7. Brine draw and slow rinse run at the same time. The

discharge to drain will slow down. The water in the salt tank

will lower. If water is leaving the salt tank, advance to the

next cycle.

8. The repressurize cycle is short and allows internal system

pressures to stabilize. After 1-2 minutes advance to the

next cycle.

9. Fast rinse is a full pressure rinse of the media in the tank.

The discharge to drain should be high. Advance to the next

cycle.

10. Backwash 2 is a second backwashing of the media tank.

Discharge to drain will be slow. Advance to the next cycle.

11. Fast rinse 2 is the last cycle in the recharge process. Flow

to drain will be high. This cycle is 1 min long. Allow this

cycle to complete and advance to Service.

The controller will start the rst time with a recharge scheduled

to start at the normal time of recharge. The media in the tank

will function properly until that rst recharge.

Fill the salt tank with softener salt. The display should be

showing the current time of day and the colon will be ashing.

Automatic Recharge

The control uses an internal water meter that counts the

gallons used. When the recharge setpoint (gallons of water

treated) is reached, the unit will recharge. The setpoint

depends on the capacity setting used (HE, Sd or HE) and

the hardness of the water. See Performance Data for rated

capacities and system performance.

The system is fully operational.

During normal operation (Service mode) the display will

show the current time of day with the colon blinking. This will

alternate with a display of the capacity remaining.

PLACING SOFTENER INTO OPERATION

(TURNING ON THE WATER)

Things You Might Need to Know

• When the controller is rst plugged in, it may display a

ashing hourglass and the message Err 3, this means

that the controller is rotating the camshaft to the home

position.

• The preset default time of recharge is 12:00 am.

• The 706 Series controller is programmed to recharge if

a recharge has not taken place in the last 15 days. This

setting cannot be changed.

• Make sure control power source is plugged in. The

transformer should be connected to a non-switched

power source.

• Unless changed, the settings for a newly installed system

are:

Hardness - 25 grains per gallon

Salt Setting - HE (High Efciency)

Water Used Settings - 0 gallons

Internal System clock starts at 8:00 AM

Day of the week is sunday

The rst recharge will occur when the system clock

reaches 12:00 am

Accessing History Values

The 706 control features a review level that displays the

operation history of the system. This is a great troubleshooting

tool for the control valve.

To access history values, press Recharge followed by the Salt

Amount button and hold for 3 seconds to view the Diagnostic

Codes.

NOTE: If a button is not pushed for 30 seconds the

controller will exit the history table.

Press the Time of Day button to increment through the table.

When the desired code is reached, Press the Salt Amount

button to display the value.

When the Salt Amount button is pressed to view H2 the current

ow rate will be displayed but not updated. Continue to press

and release the Salt Amount button every 5 seconds to update

the display. The ow icons on the display will ash when there

is ow through the softener.

Code Description Notes

H1 Days since last recharge Days since last recharge

H2 Current ow rate Gallons per minute

H3 Current day of week Current day of week

H4 Water used today since 0200

In gallons,

max value displayed 9,999

max value stored 65,535

H5 Water used since last recharge

A0 Average water usage for day 0

A1 Average water usage for day 1

A2 Average water usage for day 2

A3 Average water usage for day 3

A4 Average water usage for day 4

A5 Average water usage for day 5

A6 Average water usage for day 6

PLACING SOFTENER INTO OPERATION

cont inued

OM26KCS, OM32KCS, OM36KCS DE11 • 15

Item No. QTY Part No. Description

1 ........... 1 .......4001579......... Softener Cabinet

2 ........... 1 .......4001585......... Softener Cabinet Cover

3 ........... 1 .......4001569......... Salt Lid

4 ........... 1 .......15022............. Softener Cabinet Cover Seal

5 ........... 2 .......15071............. Softener Cabinet Cover

Screw

6 ........... 1 .......4001590......... Controller OM26KCS

........4001591......... Controller OM32KCS

........4001592......... Controller OM36KCS

7 ........... 1 .......20089-6 ......... Resin Tank OM26KCS

........20093-7 ......... Resin Tank OM32KCS and

OM36KCS

8 ........... 1 .......15056-2 ......... Brine Well Tube

9 ........... 1 .......15024............. Brine Well Cap

10 ........... 1 .......15061-4 ......... Brine Valve Assembly

11 ........... 1 .......4001588......... Acorn Nut

TANK ASSEMBLY

12 ........... 1 .......4001564......... Valve Assembly with Bypass

OM26KCS

........4001565......... Valve Assembly with Bypass

OM32KCS and OM36KCS

13 ........... 1 .......400985........... Distributor Assembly

14 ........... 1 .......400562........... Distributor Upper Basket

Not Shown

1 .......20668............. Conditioning Resin

OM26KCS 0.82 ft

OM32KCS 1.00 ft

OM36KCS 1.09 ft

Item No. QTY Part No. Description

16 • DE11 OM26KCS, OM32KCS, OM36KCS

Item No. QTY Part No. Description

1 ........... 1 .......4000864......... Assembly, 706 Controller

Cover

2 ........... 1 .......4001576......... Valve Body Assy, Volumetric

Includes Item #18 OM26KCS

........4000889......... Valve Body Assy, Volumetric

Includes Item #18 OM32KCS

and OM36KCS

3 ........... 1 .......3007947......... Valve Disc Kit

4 ........... 1 .......3022012......... Top Plate

5 ........... 1 .......4000871......... Female Elbow, 3/8 NPT to

3/8 Tubing

6 .......... 12 ......1234170......... Screw, Top Plate

7 ........... 1 .......3022017......... Spring, Top Plate

8 ........... 1 .......3022013......... Camshaft, Rell First

9 ........... 1 .......1000589......... Yoke, Camshaft

10 ........... 2 .......1234170......... Screw, Yoke

11 ........... 1 .......4001291......... 368 Valve Motor/Optical

Sensor Assy

12 ........... 1 .......1000269......... Injector Cap Assembly

13 ........... 1 .......3025329......... “H” Assy Injector w/O-rings

and Screen, Lt Purple, 9 Inch

Tank OM26KCS

........4000880......... “J” Assy Injector w/O-rings

and Screen,, Lt Blue, 10

Inch Tank OM32KCS and

OM36KCS

14 ........... 1 .......1243510......... Assembly, Rell Cont, .33

gpm

15 ........... 2 .......1030502......... Ball, Backwash, Brine Rell

Controller

16 ........... 1 .......1010154......... O-ring, Tank

17 ........... 1 .......1232370......... O-ring, Riser

18 ........... 1 .......3027839......... Meter Assembly

19 ........... 1 .......1235446......... Assembly, Sensor Cable

20 ........... 1 .......3031825......... Kit, O-ring, Manifold

21 ........... 1 .......4000886......... Bypass

1 .......4000392......... Main Assembly

2 .......3027832......... Retainer, Manifold, SS

2 .......40576............. Clips Retainer, Plastic

1 .......3031825......... Kit, O-ring Manifold

22 ........... 1 .......4001286......... Kit, Drain Line Flow Control

OM26KCS

........4000887......... Kit, Drain Line Flow Control

OM32KCS and OM36KCS

1 .......4000390......... Drain Line Clip

1 .......1030502......... Backwash Ball

1 .......4000535......... Flow Control with O-ring

OM26KCS

........4000536......... Flow Control with O-ring

OM32KCS and OM36KCS

23 ........... 1 .......1000811 ......... 120 VAC, 60 Hz, N. America

Plug

24 ........... 2 .......4000888......... Connector Assembly, 1" NPT,

Plastic, w/O-ring and Clip

Retainer

25 ........... 1 .......4000996......... Fitting, Drain Line, 90°, 1/2

NPT, 1/2 Tube

Item No. QTY Part No. Description

VALVE ASSEMBLY

OM26KCS, OM32KCS, OM36KCS DE11 • 17

BRINE WELL ASSEMBLY CH20795

Item No. QTY Part No. Description

1 1 .CH15013-1 ...................... Brine Well w/Slots

2 1 ...CH15062 Safety Brine Valve

3 2 ...CH15070 Grommet

4 1 CH16371-16 ..................... Tubing, 3/8" x 16" Long

5 1 ...CH15024 Cap, Brine Well 4" Dia. (Caplug STP-4)

6 1 .CH15064-1 ...................... Brine Float w/One Grommet

(As purchased)

7 1 .CH15063-1 ...................... Air Check Assembly

8 2 ...BR10332 Tubing Insert, Brass

Not Shown

1 .......CH20774 ....... Overow Fitting Assembly

1 .......*CH15031-1 ... Overow Elbow

1 .......*CH15031-2 ... Overow Nut

1 .......*CH16331 ...... Gasket

*Parts included with CH20774 Overow Fitting Assembly

18 • DE11 OM26KCS, OM32KCS, OM36KCS

TROUBLESHOOTING

706W Control - Error Codes

Problem Possible Cause Solution

Err 1 is displayed. Program settings have been corrupted. Press any key. If Err 1 does not clear, replace control.

Err 3 is displayed. Control does not detect the camshaft position and is

returning to the service position.

Wait until the control returns to the service position. Flashing

hourglass in the display indicates that the motor is running

Camshaft is not turning during Err 3 display. Check that motor is connected. Verify that the motor wire

harness is connected to motor and controller module. Verify

that optical sensor is connected and in place. Verify that

motor gear has engaged the camshaft.

If everything is connected, replace components in this order:

1. Motor Assembly, Optical Sensor

2. Control

Camshaft is turning more than ve minutes to nd the

service position:

Verify that optical sensor is in place and connected to wire.

Inspect for debris in the camshaft slots.

If motor continues to rotate indenitely, replace the following

components in this order:

1. Optical Sensor

2. Control

System

Problem Possible Cause Solution

Salt tank overow. Loose salt line connection. Ensure all salt line connections are tight.

Drain line restricted with debris. Clean drain control.

Flowing or dripping water at drain or salt line

after recharge.

Debris is preventing #4 valve disc from

closing.

Remove debris.

Worn #4 valve disc. Replace valve discs.

Hard water leakage after recharge. Improper recharge. Repeat recharge after making certain correct

salt dosage was set.

Leaking of external bypass valve. Replace bypass valve.

O-Ring around riser pipe damaged. Replace O-ring.

Valve will not draw brine. Restricted drain line. Remove restriction.

Injector plugged. Clean injector and screen.

Debris is preventing valve discs from closing. Remove foreign matter from valve discs.

Control will not recharge automatically. AC adapter or motor not connected. Connect power.

Defective motor. Replace motor.

Meter clogged with debris. Unit will recharge

every 7 days anyway.

Remove and clean meter.

Control recharges at wrong time of day. Time of Day set incorrectly. Set the correct Time of Day.

Intermittent salt draw. Low water pressure. Maintain a minimum of 20 psi

(1.3 bar) feed.

No conditioned water after recharge. No salt in salt tank. Add salt to salt tank.

Injector plugged. Clean injector and screen.

Backwashes or rinses at excessively low or

high rate.

No drain line ow control. Install drain line ow control.

Restricted drain line. Remove restriction.

Runs out of conditioned water between

recharges.

Control improperly programmed. Verify salt dosage.

Flow indicator on control does not display

service ow.

Bypass valve in bypass position. Remove bypass valve from bypass.

Meter cable dislodged from valve. Fully insert meter cable into valve.

Meter clogged with debris. Remove and clean meter.

OM26KCS, OM32KCS, OM36KCS DE11 • 19

Valve Disc Operation

When the 706W control is lifted up (Figure 22 Control

Removed) and the cover is removed, the appers and

camshaft are visible (Figure 23 Valve Layout).

Figure 22 Control Removed

Injector Cap

Rell

Control Cap

Figure 23 Valve Layout

TROUBLESHOOTING continued

20 • DE11 OM26KCS, OM32KCS, OM36KCS

La page charge ...

OmniFilter OM36KCS Installation Instructions Manual

Marque: OmniFilter

Modèle: OM36KCS

Taper: Installation Instructions Manual

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: OmniFilter OM36KCS
español: OmniFilter OM36KCS

OmniFilter OM36KCS Installation Instructions Manual

Ce manuel convient également à

OmniFilter OM36KCS Installation Instructions Manual

dans d''autres langues

Documents connexes

Autres documents