Vulcan TR45 Le manuel du propriétaire

Marque: Vulcan

Modèle: TR45

Catégorie: Friteuses

Taper: Le manuel du propriétaire

Ce manuel convient également à

INSTALLATION & OPERATIONAL MANUAL

VK / TR / VFRY SERIES GAS FRYERS

With KleenScreen PLUS® Filtration Systems

MODELS:

1VK45 1TR45

1VK65 1TR65

1VK85 1TR85

2VK45 2TR45

2VK65 2TR65

2VK85 2TR85

3VK45 3TR45

3VK65 3TR65

3VK85 3TR85

4VK45 4TR45

4VK65 4TR65

4VK85 4TR85

5VK45 5TR45

5VK65 5TR65

5VK85 5TR85

6VK45 6TR45

6VK65 6TR65

6VK85 6TR85

2MB VFRY18

3MB

4MB

5MB

6MB

1VK45C Shown

For additional information on Vulcan or to locate an authorized parts and

service provider in your area, visit our website at www.vulcanequipment.com

©VULCAN 3600 NORTH POINT BLVD.

DIVISION OF ITW FOOD EQUIPMENT GROUP, LLC BALTIMORE, MD 21222

WWW.VULCANEQUIPMENT.COM F-32971 REV. S (01-17)

VK / TR / VFRY SERIES GAS FRYERS

VULCAN F-32971 Rev. S (01-17)

-2-

IMPORTANT FOR YOUR SAFETY

THIS MANUAL HAS BEEN PREPARED FOR PERSONNEL QUALIFIED TO INSTALL

GAS EQUIPMENT, WHO SHOULD PERFORM THE INITIAL FIELD START-UP AND

ADJUSTMENTS OF THE EQUIPMENT COVERED BY THIS MANUAL.

POST IN A PROMINENT LOCATION THE INSTRUCTIONS TO BE FOLLOWED IN THE

EVENT THE SMELL OF GAS IS DETECTED. THIS INFORMATION CAN BE

OBTAINED FROM THE LOCAL GAS SUPPLIER.

IMPORTANT

IN THE EVENT A GAS ODOR IS DETECTED, SHUT DOWN UNITS AT THE MAIN

SHUTOFF VALVE AND CONTACT THE LOCAL GAS COMPANY OR GAS SUPPLIER

FOR SERVICE.

FOR YOUR SAFETY

DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS OR LIQUIDS

IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE.

Improper installation, adjustment, alteration, service or

maintenance can cause property damage, injury or death.

Read the installation, operating and maintenance instructions

thoroughly before installing or servicing this equipment.

VK / TR / VFRY SERIES GAS FRYERS

VULCAN F-32971 Rev. S (01-17)

-3-

TABLE OF CONTENTS

IMPORTANT FOR YOUR SAFETY…………………………………………. 2

INTRODUCTION…………………………………………………………….… 4

GENERAL…………………………………………………………….. 4

ORDERING PARTS…………….…………………………………… 4

UNPACKING…………………….…………………………………… 4

INSTALLATION……………………………….………………………………. 5

Clearances…………………….………………………….... 5

Location ………………..……….……………………….…. 5

CODES AND STANDARDS…………….………………………….. 6

ASSEMBLY …………..……………………………………………… 6

FLUE CONNECTION……………………….…….…………………. 7

ELECTRICAL CONNECTION………………..….…………………. 7

GAS CONNECTION…………………………………………………. 8

Quick-Disconnect for Units on Casters…………………… 8

GAS PRESSURE......................................................................... 8

TEST GAS SUPPLY……………………………….………………… 8

FRYERS WITH CASTERS………………………………………….. 8

LEVELING THE FRYER…………………………………………….. 9

OPERATION…………………………………………………………………… 10

OVER-TEMPERATURE SHUTDOWN…………………………….. 10

BEFORE FIRST USE………………………………………………... 10

Cleaning……………………………………………………... 10

BASIC FRYING INSTRUCTIONS………………………………….. 11

Fry Basket Guidelines……………………………………… 11

Fry Basket Capacity………………………………………... 11

EXTENDED SHORTENING LIFE………………………………….. 11

TURNING ON THE FRYER ……………………………………….. 12

PROGRAMMING THE SOLID STATE KNOB (A) CONTROL………….… 13

PROGRAMMING THE SOLID STATE (D) CONTROL………………….… 14

PROGRAMMING THE COMPUTER (C) CONTROL……………………… 15

TURNING OFF THE FRYER ………………………………………. 15

DRAINING THE TANK – FREE STANDING FRYERS…………… 16

BOIL OUT PROCEDURE – FREE STANDING FRYERS ……………...... 16

CLEANING……………………………………………………………. 17

Daily………………………………………………………….. 17

EXTENDED SHUTDOWN……………………………………………………. 17

KLEENSCREEN PLUS® INSTALLATION & OPERATION MANUAL....... 18

GENERAL ……………………………………………………………. 18

ASSEMBLY…………………………………………………………… 18

REMOVE & REPLACE KLEENSCREEN PLUS® FILTER ENVELOPE… 20

OPERATION…………………………………………………………………… 21

FILTERING PROCEDURE…………………………….................. 21

FILTERING SOLID STATE KNOB (A) CONTROLS………………………. 23

FILTERING SOLID STATE (D) CONTROLS………………………………. 24

FILTERING COMPUTER (C) CONTROLS………………………………… 25

FILTERING TIP……………………………………………………… 26

REMOVING EXCESS DEBRIS FROM THE FILTER…………… 26

FLUSH AND DISCARD…………………………………………….. 26

BOIL OUT BYPASS™………………………………………………. 27

THERMAL OVERLOAD PROTECTION RESET BUTTON…….. 27

MAINTENANCE……………………………………………………………….. 28

FLUE VENT INSPECTION…………………………………………. 28

Service in the US and Canada…………………………………...... 28

Alarms and Error Messages………………………………………... 28

TROUBLESHOOTING………………………………………………………… 29

Troubleshooting Chart………………………………………………. 29

VK / TR / VFRY SERIES GAS FRYERS

VULCAN F-32971 Rev. S (01-17)

-4-

INTRODUCTION

GENERAL

Vulcan Fryers are produced with quality workmanship and material. Proper installation,

usage and maintenance will result in years of satisfactory performance.

Before installing the fryer, thoroughly read this manual and carefully follow all instruction.

This manual is applicable to models listed on the cover page. Procedures in this manual

will apply to all models unless specified. Pictures and illustrations can be of any model

unless the picture or illustration needs to be model specific.

ORDERING PARTS

Customers may order parts directly from their local authorized service center. If not

known, call Vulcan Customer Service at 800-814-2028.

To speed up your order, provide the model number, serial number, gas type, part needed,

item part number (if known) and quantity needed.

UNPACKING

This fryer was carefully inspected before leaving the factory. The carrier assumes full

responsibility for the safe delivery upon acceptance of the shipment. Check for possible

shipping damage immediately after receipt.

If the fryer is found to be damaged, complete the following steps:

1. Carrier must be notified within 5 business days of receipt.

2. Carrier’s local terminal must be notified immediately upon discovery (note time,

date, and who was spoken to), and follow up and confirm with written or electronic

communication.

3. All original packing materials must be kept for inspection purposes.

4. The fryer cannot have been moved, installed, or modified.

5. Notify Vulcan Customer Service immediately at 800-814-2028.

Check that the following have been included:

 Crumb Rack(s)

 Basket Hanger(s)

 Tank Brush for Boil Out Procedure Only

 Adjustable Casters (4) two locking, two non-locking for freestanding fryers. Fryer

Batteries with the KleenScreen PLUS® Filtration System have casters installed from

the factory.

 Drain Pipe Extension for freestanding fryers only.

 Twin Fry Baskets (2) per fry tank

 Cleanout Rod

 Fryer Batteries with the KleenScreen PLUS® Filtration System

• Filter Pan

VK / TR / VFRY SERIES GAS FRYERS

VULCAN F-32971 Rev. S (01-17)

-5-

• Suction Tube

• Screen Assembly

• High temperature discard hose

 Manual, Quick Start Guide(s), and Warranty – Keep in safe place for future

reference.

INSTALLATION

Do not use the door or its handle to lift the fryer.

Before installing the fryer, verify that the type of gas (natural or propane) agrees with the

specifications on the fryer data plate, which is located on the inside of the door panel.

Make sure the fryer is configured for the proper elevation.

Record your fryer model, device, and serial numbers for future reference in the space

provided below. This information can be found on the fryer data plate.

Fryer Model No: ___________________________

Device: ___________________________________

Serial No: ________________________________

Clearances

 Minimum clearance from combustible construction:

6” (15 cm) from the sides of the fryer

6” (15 cm) from the back of the fryer

The fryer may be installed on combustible floors

 Minimum clearance from noncombustible construction:

0” from the sides of the fryer

0” from the back of the fryer

 Between the fryer and any open-top flame units:

16” (41 cm)

 Allow space for servicing and operation.

Location

 Install fryer in an area with sufficient air supply for gas combustion.

 Do not obstruct the flow of combustion and ventilation air.

 Provide adequate clearance for air openings into the combustion chamber.

 Do not permit fans to blow directly onto fryer.

VK / TR / VFRY SERIES GAS FRYERS

VULCAN F-32971 Rev. S (01-17)

-6-

 Keep the fryer area free and clear from combustibles.

 Avoid wall-type fans, which create cross-currents within a room. Avoid

open windows next to sides or back.

CODES AND STANDARDS

The fryer must be installed in accordance with:

In the United States:

 State and local codes, or in the absence of local codes, with:

 National Fuel Gas Code, ANSI-Z223.1/NFPA #54 (latest edition). Copies may be

obtained from The American Gas Association Accredited Standards Committee

Z223, @ 400 N. Capital St. NW, Washington, DC 20001 or the Secretary Standards

Council, NFPA, 1 Batterymarch Park Quincy, MA 02169-7471.

 NFPA Standard #96 Vapor Removal from Cooking Equipment, latest edition,

available from the National Fire Protection Association, Batterymarch Park, Quincy,

MA. 02169-7471.

 National Electrical Code, ANSI/NFPA-70 (latest edition). Copies may be obtained

from The National Fire Protection Association, Batterymarch Park, Quincy, MA.

02169-7471.

 In the commonwealth of Massachusetts all gas appliances vented through a

ventilation hood or exhaust system with a damper or with a power means of

exhaust shall comply with 248 CMR.

In Canada:

 Local codes

 CAN/CSA-B149.1 Natural Gas and Propane Installation Code (latest

edition),available from the Canadian Standards Association, 155 Queen Street,

Suite 1300, Ottawa, Ontario Canada K1P 6L1.

 CSA C22.1 Canadian Electric Code (latest edition), available from the Canadian

Standards Association, 155 Queen Street, Suite 1300, Ottawa, Ontario Canada

K1P 6L1.

ASSEMBLY

The fryer must be restrained to prevent tipping and the splashing of hot liquid. The means

of restraint may be the manner of installation, such as connection to a battery of

appliances, installing the fryer in an alcove, or by separate means such as adequate ties.

VK / TR / VFRY SERIES GAS FRYERS

VULCAN F-32971 Rev. S (01-17)

-7-

FLUE CONNECTION

Make the flue connection as follows:

 Comply with Vapor Removal from Cooking Equipment, ANSI-NFPA

Standard #96 (latest edition), available from the National Fire Protection

Association, Batterymarch Park, Quincy, MA 02269.

 Locate the fryer under a hood with adequate connection to an exhaust

duct. The hood must extend 6” (15 cm) beyond fryer on both sides.

 Clearance above the fryer should be adequate for combustion byproducts

to be removed efficiently.

 An 18” (46 cm) minimum clearance should be maintained between the flue

vent and the filters of the hood venting system.

 Never make flue connections directly to the fryer.

 Do not obstruct the flow of the gases from the appliance. Proper air

balance should be maintained in the room.

 Ensure that your ventilation system does not cause a down draft at the fryer’s flue

opening. Down drafts will not allow the fryer to exhaust properly and will cause

overheating which may cause permanent damage. Damage caused by down drafts

will not be covered under equipment warranty. NEVER allow anything to obstruct

the flue of combustibles or ventilation exiting from the fryer flue. DO NOT put

anything on top of flue area.

ELECTRICAL CONNECTION

Electrical Grounding Instructions:

This appliance is equipped with a three prong (grounding) plug for your protection

against shock hazard and should be plugged directly into a properly grounded

three-prong receptacle. Do not cut or remove the grounding prong from this plug.

Fryer must be electrically grounded in accordance with local codes, or in the

absence of local codes, with the National Electrical Code, ANSI/NFPA 70, or the

Canadian Electrical Code, CSA C22.2, as applicable.

Electrical diagram located on inside of door.

VK / TR / VFRY SERIES GAS FRYERS

VULCAN F-32971 Rev. S (01-17)

-8-

GAS CONNECTION

All gas supply connections and any pipe joint compound must be

resistant to the action of propane gases.

The gas inlet is located on the lower rear of the fryer. Codes require that a gas shutoff

valve be installed in the gas line ahead of the fryer.

The gas supply line must be at least the equivalent of ½” (12.7 mm) iron pipe for single

units and 1-1/4” (31.75 mm) for batteries. If using the optional quick-disconnect flex hose,

¾” (19 mm) iron pipe for single units and 1-1/4” (31.75 cm) iron pipe for batteries.

Make sure the pipes are clean and free of obstructions, dirt, and piping compound. A

battery requires one or two connections of appropriate size for the gas requirement.

Prior to lighting, check all joints in the gas supply line for leaks.

Use soap and water solution. Do not use an open flame.

After piping has been checked for leaks, fully purge gas pipes to remove air.

GAS PRESSURES (ALL MODELS):

The gas measured exiting the gas valve should be set at .08” W.C. (Water Column) (0.02

kPa) for natural gas and .08” W.C. (0.02 kPa) for propane gas. This fryer has been gas

calibrated at the factory to achieve maximum performance. Do not make any adjustments

to the gas valve assembly. The supply pressure should be 7-9” W.C. for natural gas and

11-12” W.C. for propane gas. If incoming pressure exceeds 14” WC (½ psig -3.45 kPa), a

step-down pressure regulator must be installed.

TESTING THE GAS SUPPLY PIPING SYSTEM:

When test pressures exceed ½ psig (3.45 kPa), the fryer and its individual shutoff valve

must be disconnected from the gas supply piping system.

When test pressures are ½ psig (3.45 kPa) or less, the fryer must be isolated from the gas

supply piping system by closing its individual shutoff valve.

Fryers with Casters:

Separate instructions for installing casters are included with the casters:

 The installation shall be made with a connector that complies with the

Standard for Connectors for Movable Gas Appliances, ANSI Z21.69, CAN/CGA-

6.16, and a quick-disconnect device that complies with the Standard for Quick-

VK / TR / VFRY SERIES GAS FRYERS

VULCAN F-32971 Rev. S (01-17)

-9-

Disconnect Devices for Use with Gas Fuel, ANSI z21.41.CSA 6.9 or Quick-

Disconnect Devices for Use with Gas Fuel.

 When installing a quick disconnect you must also install a means for limiting the

movement of the fryer. This device will prevent the gas line or quick disconnect

from being strained. The restraining device should be attached to the cutout on the

back panel. See illustration for location.

 The fryer must be installed with a connector (not supplied by Vulcan) complying

with the above codes.

 The fryer must be installed with restraining means to guard against

transmission of strain to the connector. See illustration.

 The fryer must be installed with the casters provided.

 If the restraint is ever to be disconnected, first turn the gas supply off. If

disconnection of the restraint is necessary, reconnect this restraint after the fryer

has been returned to its originally installed position.

LEVELING THE FRYER

Check the level of the fryer by placing a level on top of the fryer after gas connections

have been made.

Ensure that the fryer is level front-to-back and side-to-side in the final installed position.

If using casters, lock the wheels after unit is level.

VK / TR / VFRY SERIES GAS FRYERS

VULCAN F-32971 Rev. S (01-17)

-10-

OPERATION

Hot oil and parts can cause burns. Use care when operating,

cleaning and servicing the fryer.

Spilling hot frying compound can cause severe burns. Do not move

fryer without draining all frying compound from the tank.

Fryer is not to be used during a power outage.

OVER-TEMPERATURE SHUTDOWN

If the shortening becomes overheated, a high-temperature shutoff device will turn the gas

valve off.

If the fryer shuts down due to overheating, DO NOT power up the fryer until the shortening

temperature is below 300°F (149°C).

If an overheating situation persists, contact your local Vulcan authorized service office.

BEFORE FIRST USE

Cleaning

New units are wiped down at the factory to remove any visible signs of dirt, oil, grease,

etc. remaining from the manufacturing process.

Before any food preparation, thoroughly wash the protective oil from all surface parts and

the tank interior with hot soapy water to remove any film residue and dust or debris.

Do not use chlorine or sulfate/sulfide cleaners.

 Wash any accessories shipped with unit.

• Rinse fryer and accessories thoroughly and drain the fryer.

 Wipe tank completely dry with a soft, clean cloth.

 Close the drain valve.

 Fill the fryer tank with liquid shortening.

 Shortening level should be between the min and max lines in the fryer tank.

 Shortening will expand when heated. Do not fill the fryer tank past the

MAX line.

 Add fresh shortening as needed to maintain oil level.

VK / TR / VFRY SERIES GAS FRYERS

VULCAN F-32971 Rev. S (01-17)

-11-

BASIC FRYING INSTRUCTION

 Set the desired temperature and allow shortening to heat up to that temperature.

 Fry items that are the same size to ensure equal doneness.

 Drain or wipe dry raw or wet foods to minimize splatter when lowering into hot

shortening.

 Add fresh shortening as needed.

Fry Basket Guidelines

 Do not overfill baskets. (See table for recommended basket capacities below)

Carefully lower basket into oil.

 When frying doughnuts and fritters, turn product only once during frying.

 When cooking French fries or onion rings, shake the basket several times.

 Batter covered foods should be dropped carefully, one by one, into shortening or

basket. If you use the basket, first dip the basket into the shortening to

reduce batter-build up on basket surfaces.

 When frying is completed, remove basket or product. Hang basket on rear

hanger.

Fry Basket Capacity:

1VK / TR45 & VFRY18: Recommended pounds per basket are 2.5 lbs. (1.1 kg).

1VK / TR65: Recommended pounds per basket are 3.0 lbs. (1.4 kg).

1VK / TR85: Recommended pounds per basket are 3.5 lbs. (1.6 kg).

EXTENDING SHORTENING LIFE

Shortening life can be extended by the following guidelines:

 Do not salt foods over the fryer.

 Use good-quality shortening.

 Filter shortening daily (at a minimum).

 Replace shortening if it becomes poorly flavored.

 Keep equipment and surrounding clean. Use tank covers when not in use.

(accessory).

 Set thermostat correctly.

 Remove excess moisture and particles from food products before placing on fryer.

VK / TR / VFRY SERIES GAS FRYERS

VULCAN F-32971 Rev. S (01-17)

-12-

TURNING ON THE FRYER

(VK / TR / VFRY)A solid state knob control:

Indicator Lights

(On/Start/Heating)

Temperature Knob Control Melt Switch

Power Switch Filter Switch

(For those models with KleenScreen

PLUS® Filter Systems)

Start Button

 Open the door to the fryer. Select Liquid or Solid Shortening by pressing the

switch to the desired selection.

 Set temperature by turning the knob to the desired temperature.

 Press the power switch to the ON position. The burners will not light until the

next step is completed.

 Press the START switch once for the burners to light. The START switch is a

momentary switch and will reset after being pressed. The indicator light will

change from Red to Green. Heating light will glow Yellow.

 The power burner will cycle on and off throughout the melt cycle. When the fry

tank oil reaches 135° F the burners will stop cycling and remain on until the set

temperature is reached. Once set temperature is reached the burners will cycle

on and off to maintaining the set temperature.

(VK / TR)D solid state digital and (VK / TR)C programmable controls:

For solid state digital and programmable computer controls the power burner will light

automatically. The power burner will cycle on and off throughout the melt cycle and continue

afterwards maintaining the set temperature.

VK / TR / VFRY SERIES GAS FRYERS

VULCAN F-32971 Rev. S (01-17)

-13-

VK / TR / VFRY SERIES GAS FRYERS

VULCAN F-32971 Rev. S (01-17)

-14-

VK / TR / VFRY SERIES GAS FRYERS

VULCAN F-32971 Rev. S (01-17)

-15-

TURNING OFF THE FRYER

1. Press the power switch to the off position.

VK / TR / VFRY SERIES GAS FRYERS

VULCAN F-32971 Rev. S (01-17)

-16-

DRAINING THE TANK

Freestanding Models ONLY:

1. Turn off fryer.

2. Insert the drain extension into the drain valve. Tighten only hand tight.

3. Direct the drain spout into the container that you want to drain the shortening into.

4. Open the drain valve. The oil will drain into the container. When the container is

full or the fryer tank is empty, close the drain valve. Repeat this step until the fryer

is empty. Remove the drain extension and place it back into the provided holder.

5. It is recommended to now boil out your fry tank. Follow the Boil Out procedure.

Then perform the weekly clean-out as described under CLEANING.

6. Once tank is completely empty, boiled out and cleaned, add new shortening. Turn

on the power switch to begin heating the oil to desired temperature.

BOIL OUT PROCEDURE

Weekly or when oil is replaced:

Freestanding Models ONLY:

1. Drain the tank as described under DRAINING THE OIL.

2. Close the drain valve and fill tank with water. Use a boil out solid degreaser which can

be ordered from your local dealer. Follow the instructions on the side of the package.

Do not use chlorine or sulfate/sulfide cleaners.

3. Solution level must be between the MIN and MAX levels on the fryer tank.

4. Turn the power switch to the on position. With solid state knob controls (A), set the

temperature knob to 200°F. Press the start button. Water boils at 212°F. For solid

state digital models (D) and computer models (C) models, the temperature will

automatically set for 195-200°F. Do not bring water temperature to an overly active

boil.

5. Use the tank brush; clean the sides, bottom and heat exchanger tubes.

6. Screw the drain extension in the drain valve and hand tighten only. Drain the cleaning

solution from the tank into a container.

7. Close the drain valve and refill the tank with water. Add 1 cup (1/4 L) of vinegar to

neutralize alkaline left by the cleaner. Solution level must be between the MIN and

MAX level on the fryer tank. Press the start button for (A) and Temp Button for (D)

and C) models, to allow the solution to heat up. Allow solution to stand for a few

minutes.

8. Drain the tank according to DRAINING THE TANK. Rinse thoroughly with clear, hot

water. All traces of cleaner must be removed. Dry the tank thoroughly.

VK / TR / VFRY SERIES GAS FRYERS

VULCAN F-32971 Rev. S (01-17)

-17-

9. Close the drain valve and add shortening. Follow the FILLING TANK WITH

SHORTENING procedure in this manual. The fryer is now ready for use. Press the

start button for (A) and Temp Button for (D) and C) models, to allow the solution to

heat up.

CLEANING

Hot oil and hot parts can cause burns. Use care when operating,

cleaning, and servicing the fryer.

Daily

Clean your fryer regularly with the tank brush along with a damp cloth, and polish with a

soft dry cloth. If regular cleaning is neglected, grease will be burned on and discolorations

may form.

Fingerprints are sometimes a problem on highly polished surfaces of stainless steel. They

can be minimized by applying a cleaner that will leave a thin oily or waxy film.

 Clean all exterior surfaces of your fryer at least once daily.

 Use a damp cloth with warm water and a mild soap or detergent.

Do not use chlorine or sulfate/sulfide cleaners.

 Rinse thoroughly, and then dry with a soft dry cloth.

 Keep the fryer exterior clean and free of accumulated grease to prevent

stubborn stains from forming. If regular cleaning is neglected, grease will be

burned on and discolorations may form.

 Remove discolorations by washing with any detergent or soap and water.

 Use a self-soaping, non-metallic scouring pad for particularly stubborn

discolorations.

 Always rub with the grain of the stainless steel.

 Do not use a metallic scoring pad or harsh cleaners.

Air Filter Cleaning (VK fryers only):

The air filter needs to be cleaned at least once every three months. Pull the air filter off

and clean in a dishwasher or by hand. Dry thoroughly before replacing it into position.

There is no need to tighten the band clamp with tools.

EXTENDED SHUTDOWN

1. Thoroughly drain the fryer. Refer to DRAINING THE FRYER.

2. Clean the fryer according to CLEANING.

3. Push Power switch to the off position

4. Turn off the main gas shutoff valve.

VK / TR / VFRY SERIES GAS FRYERS

VULCAN F-32971 Rev. S (01-17)

-18-

KleenScreen Plus® Filtration System

General

The KleenScreen PLUS® filtration system filters the oil as it is pumped back into its’ respective

tank(s). Only one tank can be drained and filtered at a time. Under no circumstances should both

tanks be drained at the same time.

Assembly

• After unpacking, wash the filter pan, crumb basket and filter screen assembly. Make sure

you remove the insert located inside the filter screen. Use dishwashing detergent and warm

water, (parts are dishwasher safe). Rinse the filter pan, crumb basket and filter screen

components completely and wipe all parts dry with a clean cloth.

• Pull out the filter drawer all the way leaving the filter pan opening exposed.

• Place the filter tank into the filter drawer making sure that the pins on the bottom of the filter

pan line up with the holes in the filter drawer. Position the filter screen assembly into the

suction tube clip in the filter pan positioning the filter screen assembly flat on the bottom of

the filter pan.

• Carefully line up the suction tube nozzle so that it mates with the oil receptacle block

mounted on the frame of the fryer battery. Close the drawer. See Figures 1, 2 3 and 4

Suction Tube

Filter Screen

Filter Insert

Knurled Bottom

Fitting

Fig. 1

VK / TR / VFRY SERIES GAS FRYERS

VULCAN F-32971 Rev. S (01-17)

-19-

Fully assembled filter screen assembly:

Fig. 2

Secure Tube with

Suction Tube Clip

Filter Screen Lays

Flat On Bottom of

Filter Pan

Fig. 3

Micro-Filtration Fabric Envelope Accessory Assembly:

Same Suction Tube

Fabric Envelope Insert

(Different from Screen Assembly)

Fabric Envelope

Closing Clip

Same Knurled Knob

Fig. 4

VK / TR / VFRY SERIES GAS FRYERS

VULCAN F-32971 Rev. S (01-17)

-20-

INSTRUCTIONS TO REMOVE & REPLACE KLEENSCREEN PLUS® FILTER ENVELOPE

FOR ABSOLUTE FILTRATION & MAXIMUM FLOW RATE WE RECOMMEND YOU CHANGE YOUR FILTER

ENVELOPES AT EVERY OIL CHANGE (10-14 DAYS DEPENDING ON OIL USAGE).

Step 1

Discard all oil from the filter vessel, (see pages 23 or 24). When the

filter pan is empty, use a spatula and scrape off all debris left on the

filter envelope and in the filter pan.

Step 2

Unscrew “S” Tube from filter by turning the Bottom Knurled fitting

counter- clockwise.

Step 3

Remove SST Closure Clip by lifting off one side.

Step 4

Remove SST Filter Screen Insert and wash insert with hot water and

dry thoroughly. The Filter Screen Insert is dishwasher safe. Place the

insert into a new KleenScreen PLUS® Filter envelope.

DO NOT WASH FABRIC ENVELOPE

Step 5

Place Filter Screen Insert into the fabric envelope making sure that the

holes line up. Fold over the other end of the envelope and place SST

Closure Clip on – hinge over and firmly press clip all the way down to

secure and seal filter assembly. Making sure that the folded end is face

down; screw “S” Tube Assembly onto the Filter Assembly. Tighten the

Bottom Knurled fitting. When tightened, the “S” Tube assembly should

be perpendicular to the long side of the filter assembly.

Step 6

Reposition the filter tube into the provided clip. Align filter tube so that

the end of the “S” Tube engages the Oil Receptacle fitting each time the

drawer is opened and closed.

La page charge ...

Vulcan TR45 Le manuel du propriétaire

Marque: Vulcan

Modèle: TR45

Catégorie: Friteuses

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Vulcan TR45 Owner's manual

Vulcan TR45 Le manuel du propriétaire

Ce manuel convient également à

Vulcan TR45 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents