Baby Lock Jazz II Mode d'emploi

Never operate this sewing machine if it has a damaged cord or plug, if it is not working properly,

if it has been dropped or damaged, dropped into water. Return this sewing machine to the nearest

authorized Baby Lock retailer for examination, repair, electrical or mechanical adjustment.

This product is intended for household use.

-1-

The sewing machine's rating is 100V-120Vac

20.If one of the LED lamp

s is damaged or broken, it must be replaced by the manufacture or its

service agent, in order to avoid a hazard.

21.Never place anything on the foot controller.

22.Use only the foot controller type YC-485EC manufactured by Yamamoto Electric Co., Ltd.

23.The supply cord connected with the foot controller cannot be replaced. If the cord is damaged

the foot controller should be scrapped.

-2-

Keep the carton and packing materials. You may have to take or send the machine to be

repaired. If you do not pack it properly, or do not use the right packing material, the machine

could be damaged.

IMPORTANT

PLEASE READ THESE INSTRUCTIONS BEFORE YOU USE THE MACHINE.

This packing material is designed to prevent damage. Save this packing material if you

need to take or send this machine to be repaire

d.

To use the machine safely

1. Make sure you watch the needle carefully while you are sewing. Do not touch the

handwheel, thread take-up lever, needle, or other moving parts.

2. Turn off the main power and unplug the cord in the following circumstances :

When you have stopped using the machine

When you are replacing or removing the needle or any other part

If there is a power failure w

hile you are using the machine

If you are checking or cleaning the machine

Leaving the machine unattended

3.Do not store anything on the foot controller.

4.Plug the machine directly into the wall. Do not use extension cords.

To give your machine a longer life

1. Do not store this machine in direct sunlight or in high humidity conditions. Do not use or

store the machine near a heater, iron,

halogen lamp or other hot objects.

2. Use only mild soaps or detergents to clean the case. Benzene, thinner, and scouring

powders can damage the case and machine, and should never be used.

3. Do not drop or hit the machine.

4. Always consult this manual before you replace or attach presser feet, the needle, or any

other parts to make sure you attach them correctly.

To repair or adjust the machine

If the machine breaks down or needs adjustment, first follow the troubleshooting table to

inspect and adjust the machine yourself. If the problem is still there, consult your local

authorized Baby Lock retailer.

-3-

INTRODUCTION

Thank you for purchasing this machine.

Before using this machine, carefully read the "IMPORTANT SAFETY INSTRUCTIONS",

and then study this manual for the correct operation

of the various functions.

In addition, after you have finished reading this manual, store it where it can quickly be

accessed for future reference.

TABLE OF CONTENTS

-4-

FLAT BED ATTACHMENT

MAIN PARTS

ACCESSORIES

REMOVING THE FLAT BED ATTACHMENT

OPENING THE ACCESSORY COMPARTMENTS

FREE ARM STYLE

CONNECTING THE MACHINE

8

POWER CONNECTION 8

FOOT CONTROLLER

8

CHANGING THE PRESSER FOOT

CHANGING THE NEEDLE

THREADING THE MACHINE 10

BOBBIN WINDING

LOWER THREADING

11

UPPER THREADING 12

USING NEEDLE THREADER

DRAWING UP THE LOWER THREAD

CONTROLS

PATTERN SELECTION DIAL AND INDICATOR

STITCH LENGTH DIAL

STITCH WIDTH DIAL

REVERSE SEWING LEVER

DROP FEED DOG LEVER

KNEE LIFTER

SETTING THE THREAD TENSION

FABRIC, THREAD AND NEEDLE COMBINATIONS

STRAIGHT STITCH SEWING

ZIGZAG STITCH SEWING

BLIND HEM STITCH SEWING

OVERCASTING-OVERLOCKING

MULTI-STITCH ZIGZAG

STRETCH STITCH SEWING

SEWING BUTTONHOLES

INSERT ZIPPERS AND PIPING

STRAIGHT STITCH SEAMING AND QUILTING

DARNING/FREE MOTION QUILTING

PATCH WORK

APPLIQUE

SCALLOP STITCH

CARING FOR YOUR MACHINE

TROUBLESHOOTING

INSTRUCTIONS BEFORE YOU USE THE MACHINE

INTRODUCTION

UNPACKING/REPACKING INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

RECYCLING (EU ONLY)

1

2

3

PRESSER FOOT PRESSURE ADJUSTMENT DIAL

5

7

9

10

13

14

15

16

17

18

19

21

22

24

25

26

27

28

29

31-32

TWIN NEEDLE SEWING

30

33

STITCH REFERENCE CHART

34

BUTTONHOLES FINE TUNING

35-38

-5-

MAIN PARTS

1

Face Cover

2

Reverse Lever

3

Thread Cutter

4

Thread Take-Up Lever (inside)

5

Thread Tension Regulator

6

Thread Guide Plate

7

Spool Pin

8

Spool Cap

9

Bobbin Winder Pretension Disc

10

Bobbin Winder Shaft

22

Thumb Screw Holes

12

Knee Lifter Mounting Slot

13

Flat Bed Attachment With Accessory

Compartments

14

Pattern Indicator

15

Stitch Length Dial

16

Stitch Width Dial

17 Presser Foot Pressure Adjustment Dial

18

Bobbin Winder Stop

19

Handwheel

20

Pattern Selection Dial

11

17

1

3

13

12

2

14

15

10

16

9

7

5

6

4

8

18

19

20

21

Buttonhole Fine Tuning

22

11

Top Cover

23

24

Needle Stop Position Button

23

Needle Up/Down Button

MAIN PARTS

-6-

22

Carrying Handle

23

Drop Feed Dog Lever

24

Main Power Switch

25

Power Cord Receptacle

26

Power Cord

27

Lower Thread Guide

28

Needle Threader

29

Buttonhole Lever

30

Presser Foot Holder Screw

31

Needle Plate

27

32

Bobbin Cover

33

Presser Foot Lever

34

Presser Foot Holder

35

Needle Clamp Screw

36

Needle Bar Thread Guide

37

Presser Foot

Needle Threader Lever

29

31

32

33

34

40

35

39

36

37

38

30

38

24

25

22

23

26

28

Foot Control Jack

Foot Controller

39

40

FLAT BED ATTACHMENT

Removing The Flat Bed Attachment

2

Free-Arm Style

The accessories are stored in the compartments inside

the flat bed attachment.

Pull the top of the flat bed attachment to open the

accessory compartments.

Free-arm sewing is convenient for sewing tubular and

hard to reach areas. To change your machine to the free

arm style, remove the flat bed attachment.

1

Slide the flat bed attachment to the left to release it.

-7-

17

17.

Knee Lifter

Screwdrivers

18.

Quilting Guide

18

19

20

19.

Vertical Spool Pin

20.

Spool Pin Felt (2)

Darning/Free Motion Quilting Foot

1/4 Inch Quilting Foot

21.

Dust Cover

21

90/14 3 needles

(One on machine)

Flat bed attachment11

Accessory Compartments

12

US ONLY

Power Connection

2

3

Connect the power supply cord to the machine.

Connect the power supply plug to a wall outlet.

Use regular household electricity for power source. Using

other power sources may result in fire, electric shock, or

damage to the machine.

Turn off the main power and remove the plug in the following

circumstance:

When you are away from the machine

After using the machine

When the power fails during use

When the machine does not operate correctly due to a bad

connection or a disconnection

During electr

ical storms

W ARNING

This appliance has a polarized plug (one bla de wider tha n

the other). To re duce the risk of electrical shock, this plug

is intended to fit in a polarized outlet only one way. If the plug

does not fit fully into the outlet please reverse the plug. If it

still does not fit, contact a qualified electrician to install the

proper outlet. Do not modify the plug in any way.

Do not use extension cords or multi-plug adapters with

many other appliances plugged in to them. Fire or electric

shock may result.

CAUTION

Do not touch the plug with wet hands. Electric shock may

result.

When unplugging the machine, always turn off the

main power first. Always grasp the plug to remove it from

the outlet. Pulling on the cord may damage the cord, or lead

to fire or electric shock.

Do not allow the power cord to be cut , damaged, modified,

forcefully bent, pulled, twisted, or bundled. Do not place

heavy object on the co

rd. Do not subject the cord to heat.

These behaviors may damage the cord and cause fire or

electric shock. If the cord or plug is damaged, take the

machine to your authorized Baby Lock retailer for repairs

before continuing use.

Unplug the power cord if the machine is not to be used for a

long period of time, otherwise a fire may result.

Connect the foot control to the machine by inserting the foot control

pin into the foot control receptacle located on the right side of sewing

machine.

When you press the foot controller lightly, the machine will run at

a low speed.

When you press harder, the speed of machine will increase.

When you take your foot off the foot controller, the machine will stop.

You sho

uld make sure that no items are placed on the foot controller

when the machine is not in use.

CAUTION

Foot Controller

Do not allow pieces of cloth and dust to build up on the foot controller.

Doing so could cause a fire or an electric shock.

1

2

Use only foot controller provided with this

machine.Foot Controller: Model YC-485EC

-8-

1

Place machine on a sturdy table and make sure

the main power switch is in the OFF position.

:ON

:OFF

Main Power Switch

Always turn off the power before you change the presser foot.

If you leave the power on and step on the controller, the machine

will start and you may be injured.

Always use the correct presser foot for the stitch pattern you have

chosen. If you use the wrong presser foot, the needle may strike the

presser foot and bend or break, and may cause injury.

Only use presser feet that have been designed to b

e used with this

machine.

Using any other presser foot may damage machine or cause

personal injury.

CAUTION

-9-

Knee Lifter (see page 16)

OR

18

the notch in presser foot holder.

Presser foot holder notch

To re-attach, tighten the screw after aligning the presser foot

holder with lower left side of presser bar.

,

and push it up as

THREADING THE MACHINE

Bobbin Winding

1.Place a spool of thread onto the spool pin with

thread winding off counterclockwise and slide

the appropriate spool cap on spool pin until it’s

against the spool of thread.

2.Pass thread through the thread guide as shown.

3.Pass thread through the bobbin winder thread

guide.

4.Guide thread from bobbin winder thread guide

through pretension disc as shown.

5.Insert thread through ho

le in bobbin from inside-out.

6.Place the bobbin on bobbin winder shaft and push

to the right to engage bobbin winder.

7.Hold the end of thread and start the machine.

WINDING THE BOBBIN

If the spool of thread is not correctly placed, the thread may

tangle on the spool.

Make sure you fo llow the instructions carefully. If you do not cut

the exce ss thread completely before winding the bobbin, when

the

bobbin thread runs low it may tangle around the bobbin and

cause the needle to break.

CAUTION

-10-

8.After the bobbin winds a few turns, stop the

machine and cut the thread as close to the hole as

possible.

9.Start the machine again by pressing foot control

and wind bobbin at medium speed.

10.The bobbin winding will stop when bobbin is full.

11.Push the bobbin and shaft to the left.

Remove the bobbin from the shaft and cut the

thread.

10 11

5

6

7

Pretension disc

8

9

Thread gui d e

Lower Threading

-11-

1

4.While lightly holding down bobbin with your right

hand, guide the thread through the slot, pull the

thread toward you to cut it with cutter as shown,

and then replace the bobbin cover and close.

cut

Slot

This machine uses Class 15 bobbins. To purchase

additional bobbins, please see your Baby Lock retailer.

Upper Threading

-12-

1

Raise presser foot lever.

2

Rotate the handwheel toward you to raise the take-up lever into the highest position.

3

Place a spool of thread onto the spool pin and secure with proper size spool

cap.

4

Pass the thread under thread guide and around pretension disc for upper threading.

5

Bring thread forward and down the right channel, then to the left and up the left

channel.

6

Pull the thread through and into the take-up lever from right to left.

7

Pass the thread down the left channel and into the lower thread guide. Slide

the thread from right to left into the thread guide on the needle clamp.

8

Thread the needle from front to back or follow directions for using the needle

threader.(Please refer to page 13)

2 3

1

If necessary, horizontal spool pin may be raised

so it can be used in a vertical position.

4

6

5

7

4

Using Needle Threader

Drawing Up the Lower Thread

-13-

1 Raise the presser foot lever.

2 Hold the needle thread loosely with your

left hand and press the Needle Up/Down

button so that the needle goes down into

the needle plate and back up into the

highest position.

3

Lightly pull the top thread upward until a

loop of bobbin thread comes up.

4

Grasp the bobbin thread and pull both top

and bobbin threads under the presser

foot and to the back leaving about 5

inches of thread.

1

2

1

2

3

4

5

6

7

4

3

5

6

7

Set needle in highest position by

needle sizes 11,12,14 and 16.

1

2

3

4

pressing the needle Up/Down button.

CONTROLS

Pattern Selection Dial and Indicator

Pattern Indicator 1

Pattern Selection dial

2

The stitch patterns are printed on the inside of the machine's top cover.

To choose a stitch, simply turn the pattern selection dial in either

direction until the desired stitch is shown within the Pattern Indicator

window.

When you use the pattern selection dial to choose a pattern,

turn the handwheel toward you (counterclockwise) to set the

needle in the highest position. If the needle is in down p

osition

when you turn the pattern selection dial, the needle, presser

foot or fabric may be damaged.

CAUTION

28 stitches

SS

Stitch Length Dial

Depending on the selected stitch, you may need to

adjust the stitch length for best results.

The numbers marked on the stitch length dial represent

the stitch length in millimeters (mm) (1/25 inch).

THE HIGHER THE NUMBER, THE LONGER THE STITCH.

With the “0"setting, material will not feed. This is used

when sewing a button.

The range is for making a satin stitch, which is used for

making b

uttonholes and few decorative stitches. The position

needed for making the satin stitch varies according to the material

and thread being used. To determine the exact dial position, first

test the stitch and length settings on a scrap piece of fabric to observe

the feeding of the material.

When you desire to sew stretch stitches ( ) turn stitch length to gold

4 for perfect setting.

4

3

2

1

0

1

2

3

Stitch length dial

1

Shorter

2

Longer

3

If the stitches are bunched together, lengthen the stitch length

and continue sewing. Do not continue sewing without

lengthening the stitch length, otherwise the needle may break

and damage machine or cause personal injury.

CAUTION

-14-

Gold

SS

Memo : Perfect setting of Stretch Stitch

Stitch Length Dial:

Stitch Width Dial:

Gold 4

Gold 7

1-Step

BH

1

Stitch Width Dial

Reverse Sewing Lever

The numbers marked on the dial represent the stitch

width. THE HIGHER THE NUMBER, THE WIDER THE STITCH.

When the Straight or Triple Stretch Stitch is selected,

the needle position can be changed from right to left

by adjusting the stitch width dial.

You can use reverse sewing for back tacking and

reinforcing seams.

To sew in reverse, push the reverse sewing lever

down as far as possible and hold it in that position

while you lightly push the foot controller. To sew

forward, release the reverse sewing l

ever. The

machine will then sew forward.

Reverse Sewing Lever

1

Drop Feed Dog Lever

The feed dog should be up for all general sewing.

Lower the feed dog for free motion darning,

embroidery, monogramming and stipple quilting.

When the feed dog is lowered, you must move the

fabric as you sew.

To lower the feed dog, slide flat bed attachment toward left

and then slide the lever to the left.

To raise the feed dog, slide the lever to the right.

-15-

Presser Foot Pressure

Adjustment Dial

You can adjust the presser foot pressure (the

amount of pressure applied to the fabric with the

presser foot)by adjusting the Presser Foot Pressure

Adjustment Dial. The higher the number, the greater

the pressure will be. Set the pressure at "2" for

normal sewing.

1

2

Stitch Width Dial

1

1 2

7

Note: Feed dog will raise once a stitch is

completed or by turning handwheel

toward you.

1

-16-

Knee Lifter

Using the knee lifter, you can raise and lower the presser

foot with your knee, leaving both hands free to handle the

fabric.

1

Align the tabs on the knee lifter with the notches in the knee

lifter mounting slot on the front of the machine. Insert the knee

lifter bar as far as possible.

If the knee lifter bar is not pushed into the mounting slot as far

as possible , it may come out during use.

3

Use your knee to move the knee lifter to the right in order

to raise the presser foot. Release the knee lifter to lower the

presser foot.

Be sure to keep your knee away from the knee lifter during

sewing. If the knee lifter is pushed during machine operation,

the needle may break or thread tension may loosen.

CAUTION

-16-

2

Lower presser foot lever.

Needle Position Control Button

2

When you press Needle position button once, the

needle is in upper position. Press it again, needle

is in lower position.

2

When you press needle stop position button, the

LED light indicates the needle position is stopped

at lower position automatically when you stop sewing.

LED

When you press needle stop position button, and

the LED light is off, it indicates the needle position

is stopped at upper position automatically when

you stop sewing.

SETTING THE THREAD TENSION

-17-

To sew zigzag stitches, the upper thread tension should be

set to a slightly weaker tension than when sewing straight

stitches.

Turn the tension dial to a lower number to

decrease the upper thread tension.

Turn the tension dial to a higher number to

increase the upper thread tension.

The thread tension must be properly balanced.

If adjustment is required, this should be made by

changing the upper thread tension.

-18-

FABRIC, THREAD AND NEEDLE COMBINATIONS

Like shown in drawing, stitches on top side of

fabric are good but bottom side tends to have a

bunch of thread, it usually means that the upper

thread is not threaded correctly or thread tension

regulator may not be set correctly. Refer to page 12

for correct upper threading.

Lightweight Fabric -thin georgette,

organdy,viole, taffeta, silk, etc.

Medium Weight Fa

bric-gingham, pique,

linen, cotton, satin, thin corduroy, velvet.

Heavyweight Fabric-gabardine, tweed,

denim,corduroy

Stretch Fabric-double knit,tricot,

spandex,jersey

70/10

9

La page charge ...

Baby Lock Jazz II Mode d'emploi

Baby Lock Jazz II Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents