Wacker Neuson HI900 G Manuel utilisateur

Operator’s Manual

IDF Heater

HI 900

Notice d’Emploi

Réchauffeurs d’air–Mise à feu indirecte

5200015145 03 0215

5200015145

EN / FR

Copyright

notice

All rights, including copying and distribution rights, are reserved.

This publication may be photocopied by the original purchaser of the machine. Any

other type of reproduction is prohibited without express written permission from

Wacker Neuson Production Americas LLC.

Any type of reproduction or distribution not authorized by Wacker Neuson Production

Americas LLC represents an infringement of valid copyrights. Violators will be

prosecuted.

Trademarks

All trademarks referenced in this manual are the property of their respective owners.

Manufacturer

Wacker Neuson Production Americas LLC

N92W15000 Anthony Avenue

Menomonee Falls, WI 53051 U.S.A.

Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957

www.wackerneuson.com

Original

instructions

This Operator’s Manual presents the original instructions. The original language of this

Operator’s Manual is American English.

5200015144 03 0215

HI 900 Foreword

wc_tx003508gb.fm

3

Foreword

Natural Gas and Diesel Heaters (without engine)

THESE HEATERS ARE SUITABLE FOR OUTDOOR OR INDOOR USE.

ADEQUATE VENTILATION MUST BE PROVIDED.

THIS HEATER IS INTENDED FOR USE PRIMARILY AS TEMPORARY HEATING

OF BUILDINGS UNDER CONSTRUCTION, ALTERATION, OR REPAIR.

WARNING

GENERAL HAZARD-FAILURE TO COMPLY WITH THE PRECAUTIONS AND

INSTRUCTIONS PROVIDED WITH THIS HEATER, CAN RESULT IN DEATH,

SERIOUS BODILY INJURY AND PROPERTY LOSS OR DAMAGE FROM HAZ-

ARDS OF FIRE, EXPLOSION, BURN, ASPHYXIATION, CARBON MONOXIDE

POISONING, AND / OR ELECTRICAL SHOCK.

f ONLY PERSONS WHO CAN UNDERSTAND AND FOLLOW THE INSTRUC-

TIONS SHOULD USE OR SERVICE THIS HEATER.

f IF YOU NEED ASSISTANCE OR HEATER INFORMATION SUCH AS AN

INSTRUCTION MANUAL, LABEL, ETC. CONTACT THE MANUFACTURER.

WARNING

WORK SITE FIRE, BURN, INHALATION, AND EXPLOSION HAZARDS.

f KEEP SOLID COMBUSTIBLES, SUCH AS BUILDING MATERIALS, PAPER,

OR CARDBOARD AT A SAFE DISTANCE AWAY FROM THE MACHINE AS

RECOMMENDED BY THE INSTRUCTIONS.

f NEVER USE THIS MACHINE IN SPACES WHICH DO OR MAY CONTAIN

VOLATILE OR AIRBORNE COMBUSTIBLES, OR PRODUCTS SUCH AS

GASOLINE, SOLVENTS, PAINT THINNER, DUST PARTICLES, OR

UNKNOWN CHEMICALS.

WARNING

NOT FOR HOME OR RECREATIONAL VEHICLE USE.

f OPERATE THE MACHINE ONLY FOR APPLICATIONS SPECIFIED IN

MACHINE DESCRIPTION AND INTENDED USE.

Foreword HI 900

wc_tx003508gb.fm

4

This heater is designed and approved for use as a construction heater in

accordance with Standard ANSI Z83.7–CSA 2.14. CHECK WITH YOUR LOCAL

FIRE SAFETY AUTHORITY IF YOU HAVE QUESTIONS ABOUT APPLICATIONS.

Other standards govern the use of fuel gases and heat producing products in

specific applications. Your local authority can advise you about these.

THE INSTALLATION OF THE UNIT SHALL BE IN ACCORDANCE WITH THE

REGULATIONS OF THE AUTHORITIES HAVING JURISDICTION.

In Canada, use the CSA B139 installation code for oil burning equipment.

HI 900 Foreword

wc_tx003508gb.fm

5

Diesel Heaters (with engine)

THESE HEATERS ARE SUITABLE FOR OUTDOOR USE ONLY.

THIS HEATER IS INTENDED FOR USE PRIMARILY AS TEMPORARY

HEATING OF BUILDINGS UNDER CONSTRUCTION, ALTERATION, OR

REPAIR.

WARNING

GENERAL HAZARD-FAILURE TO COMPLY WITH THE PRECAUTIONS

AND INSTRUCTIONS PROVIDED WITH THIS HEATER, CAN RESULT IN

DEATH, SERIOUS BODILY INJURY AND PROPERTY LOSS OR DAMAGE

FROM HAZARDS OF FIRE, EXPLOSION, BURN, ASPHYXIATION, CAR-

BON MONOXIDE POISONING, AND / OR ELECTRICAL SHOCK.

f ONLY PERSONS WHO CAN UNDERSTAND AND FOLLOW THE

INSTRUCTIONS SHOULD USE OR SERVICE THIS HEATER.

f IF YOU NEED ASSISTANCE OR HEATER INFORMATION SUCH AS

AN INSTRUCTION MANUAL, LABEL, ETC. CONTACT THE MANUFAC-

TURER.

WARNING

WORK SITE FIRE, BURN, INHALATION, AND EXPLOSION HAZARDS.

f KEEP SOLID COMBUSTIBLES, SUCH AS BUILDING MATERIALS,

PAPER, OR CARDBOARD AT A SAFE DISTANCE AWAY FROM THE

MACHINE AS RECOMMENDED BY THE INSTRUCTIONS.

f NEVER USE THIS MACHINE IN SPACES WHICH DO OR MAY CON-

TAIN VOLATILE OR AIRBORNE COMBUSTIBLES, OR PRODUCTS

SUCH AS GASOLINE, SOLVENTS, PAINT THINNER, DUST PARTI-

CLES, OR UNKNOWN CHEMICALS.

WARNING

NOT FOR HOME OR RECREATIONAL VEHICLE USE.

f OPERATE THE MACHINE ONLY FOR APPLICATIONS SPECIFIED IN

MACHINE DESCRIPTION AND INTENDED USE.

Foreword HI 900

wc_tx003508gb.fm

6

This heater is designed and approved for use as a construction heater in

accordance with Standard ANSI Z83.7–CSA 2.14. CHECK WITH YOUR LOCAL

FIRE SAFETY AUTHORITY IF YOU HAVE QUESTIONS ABOUT APPLICATIONS.

Other standards govern the use of fuel gases and heat producing products in

specific applications. Your local authority can advise you about these.

THE INSTALLATION OF THE UNIT SHALL BE IN ACCORDANCE WITH THE

REGULATIONS OF THE AUTHORITIES HAVING JURISDICTION.

In Canada, use the CSA B139 installation code for oil burning equipment.

SAVE THESE INSTRUCTIONS—This manual contains important instructions for

the machine models below. These instructions have been written expressly by

Wacker Neuson Production Americas LLC and must be followed during installation,

operation, and maintenance of the machines.

Machines

covered by

this manual

This manual covers machines with the following item numbers:

Machine Item Number

HI 900D, 2X20 5200014158

HI 900D, 3X16 5200014159

HI 900D, 4X12 5200014160

HI 900G, 2X20 5200014161

HI 900G, 3X16 5200014163

HI 900G, 4X12 5200014164

HI 900DGM, 2X20, EB 5200014165

HI 900DGM, 2X20, SB 5200014166

HI 900 Foreword

wc_tx003508gb.fm

7

Machine

identification

A nameplate listing the model number, item number, revision number, and serial

number is attached to this machine. The location of the nameplate is shown above.

Serial number

(S/N)

For future reference, record the serial number in the space provided below. You will

need the serial number when requesting parts or service for this machine.

Machine

documentation

 From this point forward in this documentation, Wacker Neuson Production

Americas LLC will be referred to as Wacker Neuson.

 Keep a copy of the Operator’s Manual with the machine at all times.

 Use the separate Parts Book supplied with the machine to order replacement

parts.

 If you are missing either of these documents, please contact Wacker Neuson to

order a replacement or visit www.wackerneuson.com.

 When ordering parts or requesting service information, be prepared to provide

the machine model number, item number, revision number, and serial number.

Expectations

for

information in

this manual

 This manual provides information and procedures to safely operate and

maintain the above Wacker Neuson model(s). For your own safety and to

reduce the risk of injury, carefully read, understand, and observe all instructions

described in this manual.

 Wacker Neuson expressly reserves the right to make technical modifications,

even without notice, which improve the performance or safety standards of its

machines.

 The information contained in this manual is based on machines manufactured

up until the time of publication. Wacker Neuson reserves the right to change

any portion of this information without notice.

 The illustrations, parts, and procedures in this manual refer to Wacker Neuson

factory-installed components. Your machine may vary depending on the

requirements of your specific region.

wc_gr011381

Serial Number:

Foreword HI 900

wc_tx003508gb.fm

8

CALIFORNIA

Proposition

65 Warning

Combustion exhaust, some of its constituents, and certain vehicle components

contain or emit chemicals known to the State of California to cause cancer and

birth defects or other reproductive harm.

Laws

pertaining to

spark

arresters

NOTICE: State Health Safety Codes and Public Resources Codes specify that in

certain locations spark arresters be used on internal combustion engines that use

hydrocarbon fuels. A spark arrester is a device designed to prevent accidental

discharge of sparks or flames from the engine exhaust. Spark arresters are

qualified and rated by the United States Forest Service for this purpose. In order to

comply with local laws regarding spark arresters, consult the engine distributor or

the local Health and Safety Administrator.

Manufacturer’s

approval

This manual contains references to approved parts, attachments, and

modifications. The following definitions apply:

 Approved parts or attachments are those either manufactured or provided by

Wacker Neuson.

 Approved modifications are those performed by an authorized Wacker

Neuson service center according to written instructions published by Wacker

Neuson.

 Unapproved parts, attachments, and modifications are those that do not

meet the approved criteria.

Unapproved parts, attachments, or modifications may have the following

consequences:

 Serious injury hazards to the operator and persons in the work area

 Permanent damage to the machine which will not be covered under warranty

Contact your Wacker Neuson dealer immediately if you have questions about

approved or unapproved parts, attachments, or modifications.

Table of Contents

HI 900

wc_bo5200015144_03TOC.fm

9

Foreword 3

1 Safety Information 13

1.1 Signal Words Used in this Manual ..................................................... 13

1.2 Machine Description and Intended Use ............................................. 14

1.3 Operating Safety ................................................................................ 15

1.4 Safety Guidelines for Operating Combustion Burners ....................... 17

1.5 Service Safety .................................................................................... 18

1.6 Safety Guidelines for Operating Gensets ........................................... 20

1.7 Safety Guidelines for Towing the Machine ......................................... 22

1.8 Safety Guidelines for Lifting and Transporting the Machine ............... 23

1.9 Reporting Safety Defects ................................................................... 23

2 Labels 24

2.1 Label Locations .................................................................................. 24

2.2 Label Meanings .................................................................................. 25

3 Lifting and Transporting 34

3.1 Lifting the Machine ............................................................................. 34

3.2 Preparing the Machine for Transport on a Truck or Trailer ................ 36

3.3 Before Towing Checklist ..................................................................... 37

3.4 Testing the Breakaway System (Electric Brakes) .............................. 38

3.5 Testing the Breakaway System (Hydraulic Surge Brakes) ................. 40

4 Operation 42

4.1 Preparing the Machine for First Use ................................................... 42

4.2 Recommended Fuel - DSL ................................................................. 42

4.3 Refueling the Machine ........................................................................ 43

4.4 Features and Controls ........................................................................ 44

4.5 Control Panel ...................................................................................... 45

4.6 General Sequence of Operation ......................................................... 46

4.7 Positioning the Machine for Indoor Use ............................................. 47

4.8 Positioning the Machine for Outdoor Use ........................................... 49

4.9 Suggested Venting ............................................................................. 51

4.10 Electrical and Grounding Requirements ............................................. 52

4.11 Power Requirements for Third-Party Generators ............................... 52

4.12 Connecting Power to the Machine ..................................................... 53

4.13 Connecting the Gas Line .................................................................... 54

Table of Contents

HI 900

wc_bo5200015144_03TOC.fm

10

4.14 Connecting to a Fuel Cylinder .............................................................55

4.15 Flex Ducting Options ...........................................................................56

4.16 Installing the Heater Duct ....................................................................57

4.17 Pre-Starting Checks ............................................................................58

4.18 Connecting and Using the Remote Thermostat ..................................59

4.19 Starting the Generator (if equipped) ....................................................60

4.20 Starting the Machine ...........................................................................61

4.21 Stopping ..............................................................................................63

4.22 Emergency Shutdown Procedure ........................................................64

4.23 Monitoring the Operating Parameters .................................................65

4.24 Operating at High Elevations ...............................................................66

4.25 Adjusting the Air Output Volume .........................................................67

4.26 Using the Recirculation Damper ..........................................................68

4.27 Operating States of the Beckett Burner Controller ..............................69

4.28 Operating States of the Riello Burner Controller .................................73

5 Factory-Installed Options 76

5.1 Variable Frequency Drive (VFD) .........................................................76

5.2 Trailer ..................................................................................................76

5.3 Generator ............................................................................................77

5.4 Diesel Burner .......................................................................................77

5.5 Natural Gas (NG)/Liquid Propane (LP) Burner ....................................77

6 Accessories 78

6.1 Available Accessories .........................................................................78

7 Burner Setup—Oil 79

7.1 Factory Settings ..................................................................................79

7.2 Setting up the Burner ..........................................................................79

7.3 Background .........................................................................................79

7.4 Setting/Checking the Electrodes .........................................................83

7.5 Replacing the Burner Nozzle ...............................................................85

7.6 Setting the “Z” Distance and Head Position ........................................87

7.7 Adjusting the Air Settings ....................................................................89

7.8 Adjusting the Fuel Pressure—Oil Burner ............................................90

8 Burner Setup—Gas 91

8.1 Factory Settings ..................................................................................91

Table of Contents

HI 900

wc_bo5200015144_03TOC.fm

11

8.2 Setting up the Burner ......................................................................... 92

8.3 Removing the Combustion Head ....................................................... 94

8.4 Adjusting the Ionization Probe and the Electrode .............................. 95

8.5 Changing the Burner Orifice ............................................................... 96

8.6 Checking the Burner Air Damper Setting ........................................... 97

8.7 Adjusting the Head Setting ................................................................. 98

8.8 Checking the Supply Gas Pressure ................................................... 99

8.9 Checking and Adjusting the Burner Gas Pressure ........................... 101

8.10 Changing the Burner Type (from Oil to NG or LP) ........................... 103

8.11 Changing the Burner from Natural Gas Burning to LP Burning ........ 104

8.12 Changing the Gas Burner Regulator Spring ..................................... 105

9 Maintenance 106

9.1 Periodic Maintenance Schedule—Oil Burners ................................. 106

9.2 Periodic Maintenance Schedule—Gas Burners ............................... 107

9.3 Cleaning the Machine ....................................................................... 108

9.4 Replacing the Blower Belt ................................................................ 109

9.5 Inspecting the Heat Exchanger ........................................................ 111

9.6 Replacing the Burner Nozzle ............................................................ 115

9.7 Replacing the Fuel Filter .................................................................. 117

9.8 Cleaning the CAD Cell ..................................................................... 118

9.9 Storing the Machine ......................................................................... 119

9.10 Preparing the Machine for Seasonal Operation ............................... 120

9.11 Connecting and Maintaining the Battery .......................................... 121

9.12 Storing the Genset ........................................................................... 122

9.13 Draining the Heat Exchanger and Resetting a Hard Lockout ........... 123

10 Genset Maintenance 124

10.1 Periodic Maintenance Schedule ....................................................... 124

10.2 Checking the Engine Oil ................................................................... 126

10.3 Servicing the Radiator ...................................................................... 127

10.4 Checking the Fuel Hoses ................................................................. 130

10.5 Changing the Engine Oil .................................................................. 131

10.6 Servicing the Air Cleaner .................................................................. 132

10.7 Checking Battery Electrolyte Level ................................................... 133

10.8 Adjusting the Fan Belt Tension ........................................................ 135

10.9 Cleaning the Fuel Filter and Filter Housing ...................................... 136

10.10 Replacing the Engine Oil Filter ......................................................... 137

10.11 Checking Air Inlet Hose .................................................................... 138

10.12 Bleeding Air from the Generator Fuel System .................................. 139

Table of Contents

HI 900

wc_bo5200015144_03TOC.fm

12

11 Basic Troubleshooting 140

11.1 Machines with Oil Burners .................................................................140

Tire Safety Information 141

Introduction to Tire Safety Information ..............................................141

12 Technical Data 154

12.1 Machine .............................................................................................154

12.2 Genset ...............................................................................................156

12.3 Trailer ................................................................................................157

13 Schematics 159

13.1 HI 900 with VFD—Electrical Schematic ............................................160

13.2 HI 900 with VFD—Electrical Schematic Components .......................161

13.3 HI 900, no VFD—Electrical Schematic ..............................................162

13.4 HI 900, no VFD—Electrical Schematic Components ........................163

13.5 Kubota Genset ..................................................................................164

13.6 Kubota Genset Schematic Components ...........................................165

HI 900 Safety Information

wc_si000827gb.fm 13

1 Safety Information

1.1 Signal Words Used in this Manual

This manual contains DANGER, WARNING, CAUTION, NOTICE, and NOTE

signal words which must be followed to reduce the possibility of personal injury,

damage to the equipment, or improper service.

NOTICE: Used without the safety alert symbol, NOTICE indicates a situation

which, if not avoided, could result in property damage.

Note: A Note contains additional information important to a procedure.

This is the safety alert symbol. It is used to alert you to potential personal hazards.

f Obey all safety messages that follow this symbol.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will result in death

or serious injury.

f To avoid death or serious injury from this type of hazard, obey all safety

messages that follow this signal word.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

f To avoid possible death or serious injury from this type of hazard, obey all safety

messages that follow this signal word.

CAUTION

CAUTION indicates a hazardous situation which, if not avoided, could result in

minor or moderate injury.

f To avoid possible minor or moderate injury from this type of hazard, obey all

safety messages that follow this signal word.

Safety Information HI 900

14 wc_si000827gb.fm

1.2 Machine Description and Intended Use

The HI900 Heaters are indirect-fired air heaters available in oil (diesel) burner and

natural gas or liquid propane (LP) burning models. The machine consists of the

following components:

 Combustion chamber and heat exchanger

 Centrifugal blower

 Single-stage burner

 High-temperature shut-down switch(es)

 Fuel tank on diesel burning models

 Trailer on mobile units

 Generator on mobile units

Fuel is consumed in a closed combustion chamber. Room air or outside air

(depending on the application) is pulled in by the centrifugal blower and blown over

the hot heat exchanger. This clean, dry, hot air is then blown into the space to be

heated by the centrifugal blower. Access to the blower assembly is protected by a

guard fitted on the air inlet.

The HI900 Heaters are intended to provide heat on outdoor sites (trailer and skid)

or indoor (skid only) sites and in other rugged applications.

This machine has been designed and built strictly for the intended use described

above. Using the machine for any other purpose could permanently damage the

machine or seriously injure the operator or other persons on the work site. Machine

damage caused by misuse is not covered under warranty.

 If your machine includes a generator, do not operate it indoors.

 If your machine does not include a generator, it may be operated indoors, but

only when it has

proper exhaust venting designed for indoor use, which meets all

applicable regulations.

This machine has been designed and built in accordance with the latest global

safety standards. It has been carefully engineered to eliminate hazards as far as

practicable, and to increase operator safety through protective guards and labeling.

However, some risks may remain even after protective measures have been taken.

They are called residual risks. On this machine, they may include exposure to:

 exhaust emissions

 hot surfaces such as exhaust vents

 fuel and fuel fumes when refueling

 high voltages and arc flash

To protect yourself and others, thoroughly read and understand the safety

information presented in this manual before operating the machine.

Wacker Neuson offers many optional accessories for the machine. These

accessories include the following:

 Remote thermostat

 Duct adapters (various sizes, available as kits, or individual ducts).

 Covers for inlet and outlets (need to be removed before operation)

 Exhaust vents and elbows

 Burner conversion kits

HI 900 Safety Information

wc_si000827gb.fm 15

1.3 Operating Safety

Operator

training

Before operating the machine:

 Read and understand the operating instructions contained in all manuals

delivered with the machine.

 Familiarize yourself with the location and proper use of all controls and safety

devices.

 Contact Wacker Neuson for additional training if necessary.

When operating this machine:

 Do not allow improperly trained people to operate the machine. People

operating the machine must be familiar with the potential risks and hazards

associated with it.

Machine

condition

Only operate the machine when:

 The heat exchanger is in proper working order.

 All safety devices and guards are in place and in working order.

 All controls operate correctly.

 The machine is set up correctly according to the instructions in the Operator’s

Manual.

 The machine is clean.

 The machine’s labels are legible.

When operating the machine:

 Do not modify or defeat the safety devices.

 Do not use worn electrical cords.

 Do not use faulty fuel supplies.

Heat

exchanger

inspection

The heat exchanger must be inspected twice a year to ensure it is in good working

order. Shorter inspection intervals are recommended for units operating under

extreme transportation or operating conditions.

Guidelines for

operator

When operating the machine:

 Remain aware of the machine’s moving parts. Keep hands, feet, and loose

clothing away from the machine’s moving parts.

 Wear protective clothing appropriate to the job site when operating the machine.

 Wear safety glasses.

When operating the machine:

 Do not operate a machine in need of repair.

 Do not smoke near the machine.

 Do not block the air inlet or outlet during machine operation.

Personal

Protective

Equipment

(PPE)

Wear the following Personal Protective Equipment (PPE) while operating this

machine:

 Close-fitting work clothes that do not hinder movement

Safety Information HI 900

16 wc_si000827gb.fm

 Safety glasses with side shields

 Hearing protection

 Safety-toed footwear

Work space

When operating the machine:

 Position the machine on a firm, noncombustible, level surface.

 Install the machine away from direct contact with rain, spraying and/or dripping

water.

 Keep the area immediately surrounding and underneath the machine clean,

neat, and free of debris and combustible materials.

 Keep the area above the machine clear of debris that could fall on the machine.

 Store the machine properly when it is not being used.

 Keep unauthorized personnel, children, and pets away from the machine.

When operating the machine:

 Do not connect ductwork between the exhaust outlet port and the supply air inlet

port.

 Never operate the machine in areas that contain flammable objects, fuels, or

products that produce flammable vapors.

 Do not position the electrical cords under the machine or over the top of the

machine.

DANGER

Exhaust gas from the burner contains carbon monoxide, a deadly poison. Exposure

to carbon monoxide can kill you in minutes.

f Never run the machine indoors or in an enclosed area unless the machine is

vented properly.

f If your machine has a trailer or generator, do not run the machine indoors.

HI 900 Safety Information

wc_si000827gb.fm 17

1.4 Safety Guidelines for Operating Combustion Burners

When using the machine:

 Make sure you have proper certification or licensing required by the locality,

state, or province in which the machine is being installed to connect natural gas

or LP.

 Clean up any spilled fuel immediately.

 Replace the fuel tank cap after refueling the machine.

 Refill the fuel tank in a well-ventilated area.

 Always keep the oil supply valve shut off if the burner is shut down for an

extended period of time.

When using the machine:

 Do not fill or drain the fuel tank near an open flame, while smoking, or while the

machine is running.

 Do not smoke when refueling the machine.

 Do not smoke when connecting natural gas or LP.

 Do not attempt to start the burner when excess oil has accumulated, when the

unit is full of vapors, or when the combustion chamber is very hot.

Note: Some machines may not be capable of supporting natural gas or LP. Please

see the burner manufacturer’s literature for more information.

DANGER

Carbon monoxide. Using this machine indoors CAN KILL YOU IN MINUTES.

Exhaust gas contains carbon monoxide (CO). This is a deadly poison you cannot

see or smell. If you can smell the exhaust, you are breathing CO. Even if you

cannot smell the exhaust, you could be breathing CO.

f NEVER operate the machine inside an enclosed area, such as a home, tunnel,

or garage unless it is vented properly.

f ONLY use the machine outside and far away from windows, doors, and vents.

These openings can pull in exhaust gas.

f ALWAYS use a battery-powered or battery-backup CO alarm in nearby struc-

tures. Even when you use the machine correctly, CO may leak into nearby

structures.

f If you start to feel sick, dizzy, or weak after the machine has been running, move

to fresh air IMMEDIATELY. See a doctor. You could have carbon monoxide

poisoning.

WARNING

Fire and explosion hazard. Cold fuel may gel, fail to ignite, and accumulate in the

heat exchanger. This accumulated fuel may explode during burner ignition.

f Always preheat the fuel before switching power to the burner.

Safety Information HI 900

18 wc_si000827gb.fm

1.5 Service Safety

Licensing/

training/

 Only qualified personnel who possess the proper certification or license

required by the locality, state, or province in which the machine is being installed

are allowed to make connections to natural gas or LP.

 Only trained personnel should troubleshoot or repair electrical problems

occurring with the machine.

Cleaning

When cleaning and servicing the machine:

 Keep the area around the burner free of debris such as leaves, paper, cartons,

etc.

 Keep the machine clean and labels legible.

When cleaning the machine:

 Do not clean the machine while it is running.

 Never use gasoline or other types of fuels or flammable solvents to clean parts.

Fumes from fuels and solvents can become explosive.

Maintenance

guidelines

When maintaining the machine:

 Keep the fuel lines in good condition and properly connected.

 Allow the burner to cool before maintaining the machine.

 Reinstall the safety devices and guards after repairs and maintenance.

 Keep all electrical cords away from heat, oil, vibrating surfaces, and sharp

edges.

 Inspect all electrical cords before each use and replace damaged cords.

Replacing

parts and

labels

When maintaining the machine:

 When replacement parts are required for this machine, use only Wacker

Neuson replacement parts or those parts equivalent to the original in all types of

specifications, such as physical dimensions, type, strength, and material.

 Replace all missing and hard-to-read labels.

 Replace or repair electrical components with components that are identical in

rating and performance as the original component.

Accessories,

safety devices,

and

modifications

When using the machine:

 Use only accessories/attachments that are approved by Wacker Neuson.

When using the machine:

 Never operate the machine if any safety devices or guards are missing or

inoperative.

 Do not defeat safety devices.

 Do not modify the machine without the express written approval of the

manufacturer.

Personal

Protective

Equipment

(PPE)

Wear the following Personal Protective Equipment (PPE) while servicing or

maintaining this machine:

 Close-fitting work clothes that do not hinder movement

HI 900 Safety Information

wc_si000827gb.fm 19

 Safety glasses with side shields

 Hearing protection

 Safety-toed footwear

In addition, before servicing or maintaining the machine:

 Tie back long hair.

 Remove all jewelry (including rings).

Safety Information HI 900

20 wc_si000827gb.fm

1.6 Safety Guidelines for Operating Gensets

This machine is built with user safety in mind; however, like any electrical device it

can present serious hazards if improperly operated and serviced. Follow

instructions carefully. Should questions arise during operation or service of this

equipment, contact your Wacker Neuson dealer.

General

precautions

 Keep a multi-class, type ABC or equivalent fire extinguisher at hand when using

the genset. Refer to NFPA No. 10 for further information regarding fire

extinguishers.

 Do not use evaporative starting fluids. They are highly explosive.

 Do not store items such as excess oil, oil rags, or tools within the genset

compartment. Items stored within the genset compartment are a fire hazard and

can restrict cooling air.

Before

operating the

genset

 Know how to start, operate, and stop the genset before starting it.

 Obtain the proper training for operating the genset. Do not allow untrained

personnel to operate or service the genset.

 Check the fuel lines and the fuel tank for leaks and cracks before starting the

engine.

 Clean the genset of any spilled fuel.

DANGER

Carbon monoxide. Using a generator indoors CAN KILL YOU IN MINUTES.

Generator exhaust contains carbon monoxide (CO). This is a poison you cannot

see or smell. If you can smell the generator exhaust, you are breathing CO. But

even if you cannot smell the exhaust, you could be breathing CO.

WARNING

Electrocution hazard. Generators present special hazards during operation and

servicing. These include the risk of electrocution or severe electrical shock. Failure

to follow the safety information below can result in severe injury or death.

f Read and follow the safety instructions in this Operator’s Manual.

f Contact the genset manufacturer for additional information regarding the

genset.

WARNING

Internal combustion engines present special hazards during operation and fueling.

Failure to follow the warnings and safety instructions could result in severe injury or

death.

f Read and follow the safety instructions in this Operator’s Manual.

f Contact the genset manufacturer for additional information regarding the

genset.

La page charge ...

Wacker Neuson HI900 G Manuel utilisateur

Ce manuel convient également à

Wacker Neuson HI900 G Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents