ProCom Heating PPK80T Manuel utilisateur

IMPORTANT: Read and understand this manual before

assembling, starting or servicing heater. Improper use

of heater can cause serious injury. Keep this manual for

future reference.

Never use heater in living or sleeping areas.

Heater is suitable for outdoor use and for use on com-

bustible oors.

PORTABLE FORCED AIR HEATER

KEROSENE/DIESEL HEATER WITH BUILT-IN THERMOSTAT

OWNER’S MANUAL

PPK145T - 145,000 BTU/HR

PPK200T - 200,000 BTU/HR

PPK80T

80,000 BTU/HR

Questions, problems, missing parts? Before returning to your retailer, call

our customer service department at 1-866-573-0674, 7:30 am - 4:15 pm CST,

Monday through Friday or email customerservice@usaprocom.com

www.usaprocom.com

160930-01A2

2. Fueling

a) Personnel involved with fueling shall be

qualied and thoroughly familiar with

the manufacturer's instructions and

applicable regulations regarding the

safe fueling of heating units.

b) Only the type of fuel specied on the

heater's data plate shall be used.

c) All ame shall be extinguished and the

heater allowed to cool, prior to fueling.

d) During fueling, all fuel lines and fuel-

line connections shall be inspected for

leaks. Any leaks shall be repaired prior

to returning the heater to service.

e) At no time shall more than one day's

supply of heater fuel be stored inside

a building in the vicinity of the heater.

Bulk fuel storage shall be outside the

structure.

f) All fuel storage shall be located a mini-

mum of 25 feet (762 cm) from heaters,

torches, welding equipment and similar

sources of ignition (exception: fuel res-

ervoir integral with heater unit or any

authorized auxiliary tank connected to

heater unit).

g) Whenever possible, fuel storage shall

be conned to areas where oor pen-

etrations do not permit fuel to drip onto

or be ignited by a re at lower elevation.

h) Fuel storage shall be in accordance

with the authority having jurisdiction.

3. Use only the electrical voltage and fre-

quency specied on model plate.

4. Heater is suitable for outdoor use.

5. Heater must be grounded. Use only a

properly grounded three-wire extension

cord. Plug into grounded outlet only.

6. Use only in areas free of ammable va-

pors or high dust content.

WARNING: This product

contains and/or generates

chemicals known to the State

of California to cause cancer or

birth defects or other reproduc-

tive harm.

IMPORTANT: Read this owner’s

manual carefully and completely

before trying to assemble,

operate or service this heater.

Improper use of this heater can

cause serious injury or death

from burns, fire, explosion,

electrical shock and carbon

monoxide poisoning.

DANGER: Carbon monoxide

poisoning may lead to death!

Carbon Monoxide Poisoning: Early signs of

carbon monoxide poisoning resemble the u,

with headaches, dizziness and/or nausea. If

you have these signs, the heater may not be

working properly. Get fresh air at once! Have

heater serviced. Some people are more af-

fected by carbon monoxide than others. These

include pregnant women, persons with heart

or lung disease or anemia, those under the

inuence of alcohol and those at high altitudes.

Make certain you read and understand all

warnings. Keep this manual for reference. It

is your guide to safe and proper operation of

this heater.

1. Use only kerosene, #1/#2 diesel/fuel oil,

JET A or JP-8 fuels to avoid risk of re or

explosion. Never use gasoline, oil from

crank cases, naphtha, paint thinners,

alcohol or other highly ammable fuels.

SAFETY

TABLE OF CONTENTS

Safety ........................................................ 2

Unpacking.................................................. 3

Assembly ................................................... 3

Product Identication and Label Locations ... 4

Specications ............................................ 5

Fuels .......................................................... 5

Ventilation .................................................. 5

Operation ................................................... 6

Operation with Portable Generator ............ 7

Storing, Transporting or Shipping .............. 7

Preventative Maintenance Schedule ......... 7

Troubleshooting ......................................... 8

Service Procedures ................................... 9

Wiring Diagram ........................................ 15

Technical Service..................................... 15

Accessories ............................................. 15

Parts ........................................................ 16

Replacement Parts .................................. 21

Warranty .................................................. 22

www.usaprocom.com

3160930-01A

SAFETY

UNPACKING

7. Minimum clearance from any combustible

materials: 8 feet (244 cm) from hot air

outlet, 6 feet (183 cm) from top, and 4

feet (120 cm) from sides and inlet.

8. Locate heater on a stable and level sur-

face while hot or operating or a re may

occur.

9. Heater is acceptable for use on ooring

such as wood (a combustible material).

10. Use only in well vented areas. Before

using heater, provide at least a 3 ft

2

(2800 cm

2

) opening of fresh, outside air

for each 100,000 Btu/Hr (30 kw) of rating.

11. Keep children and animals away from

heater at all times.

12. Never start heater when combustion

chamber is hot or if fuel has accumulated

in combustion chamber.

13. This heater is equipped with a thermostat.

Heater may start at anytime.

14. Never leave a heater plugged in without

adult supervision if children or animals are

likely to be present.

15. Use caution when moving or storing

heater when fuel tank contains fuel. Fuel

spillage can occur.

16. Use heater only in accordance with lo-

cal ordinances and codes. Canadian

residents should refer to CSA standard

B139, Installation Code for Oil Burning

Equipment for recommended installation

practice.

17. Never use gasoline, crankcase drainings,

naphtha, paint thinners, alcohol or other

highly ammable fuels.

18. Never use heater where gasoline, paint

thinner or other highly ammable vapors

are present.

19. Never use heater in living or sleeping

areas.

20. Never move, handle, refuel or service a

hot, operating or plugged-in heater.

21. Never attach duct work to front or rear of

heater.

22. Heaters used in the vicinity of tarpaulins,

canvas or similar enclosure materials shall

be located a safe distance from such ma-

terials. The recommended minimum safe

distance is 10 feet (304.8 cm). It is further

recommended that these enclosure ma-

terials be of a re retardant nature. These

enclosure materials shall be securely fas-

tened to prevent them from igniting or from

upsetting the heater due to wind action.

23. Unplug heater when not in use.

24. Never block air inlet (rear) or air outlet

(front) of heater.

25. Warning to New York City Residents

For Use Only At Construction Sites in

accordance with applicable NYC codes.

26. Never use external fuel sources or tanks

that are not specically designed for use

with this heater.

Figure 1 - Wire Guard Moved to Locked

Position

1. Remove all packing items applied to

heater for shipment.

2. Remove all items from carton.

3. Check items for any shipping damage. If

heater is damaged call ProCom Heating,

Inc. at 1-866-573-0674 for replacement

parts before returning to dealer.

ASSEMBLY

WIRE GUARD

All Models

Grasp wire guard from top of shell and pull

towards front of heater until it locks into place

in slots on both sides of upper shell.

www.usaprocom.com

160930-01A4

PRODUCT IDENTIFICATION AND LABEL LOCATIONS

Fueling Label

160168-01

Warning Label

160110-03 Spn

Warning Label

160195-01 Eng/Frn

Maintenance Label

160175-01

Caution Label

160172-01

Figure 2 - Product Identication & Label Locations

(PPK200T Shown)

CSA/Control Label

PPK80T 200167-01

PPK145T 200167-02

PPK200T 200167-03

NY, MA and CA

Information Label

160169-01

Right Side

Left Side

Hot Air

Outlet

Thermostat

Knob

Wire

Guard

Fuel Tank

Cold Air

Inlet

Power

Cord

Fuel Cap

Fuel

Gauge

Serial

Number

Label

www.usaprocom.com

5160930-01A

SPECIFICATIONS

VENTILATION

Example: A 80,000 Btu/Hr (23.4 kw) heater

requires one of the following:

• a two-car garage door [16 feet (4.88 meter)

opening] raised 2.2" (5.6 cm)

• a single-car garage door [9 feet (2.74 me-

ter) opening] raised 3.3" (7.4 cm)

• two, 30" (76.2 cm) windows raised 6.2"

(13.9 cm)

FUELS

• noticeable odor

• additional fuel lter maintenance

* Use of #2 diesel/fuel oil in extreme cold

temperatures may require nontoxic anti-icer

additives.

Do not use fuels heavier than No. 2 grade

or heavy oils such as oil drained from crank-

cases. These heavy oils will not ignite properly

and will contaminate the heater.

IMPORTANT: Use a KEROSENE ONLY (blue)

or DIESEL ONLY (yellow) storage container.

Be sure storage container is clean. Foreign

matter such as rust, dirt or water will cause the

ignition control assembly to shut down heater.

Foreign matter may also require heater's fuel

system to be frequently cleaned.

PPK80T PPK145T PPK220T

Output Rating 80,000 Btu/Hr 145,000 Btu/Hr 200,000 Btu/Hr

Fuel Use only kerosene, #1/#2 diesel*/fuel oil, JET A or

JP-8 fuels

Fuel Tank Capacity 5.5 gal/20.8 L 10 gal/37.9 L 14 gal/53 L

Fuel Consumption (per hr) 0.60 gal/2.3 L 1.08 gal/4.1 L 1.64 gal/6.2 L

Pump Pressure 3.8 PSI (hot) 6.8 PSI (hot) 8.4 PSI (hot)

Electric Requirements 120 V/60 HZ 120 V/60 HZ 120 V/60 HZ

Amperage (Normal Run) 3.0 3.5 4.0

Typical Motor Speed 3400 RPM 3400 RPM 3400 RPM

Motor 1/4 hp 1/4 hp 1/4 hp

Shipping Weight 37 lbs/16.8 kg 72 lbs/32.6 kg 78 lbs/35.4 kg

Heater Weight without Fuel (approx) 32 lbs/14.5 kg 64 lbs/29 kg 68 lbs/30.8 kg

WARNING: Use only kero-

sene, #1/#2 diesel/fuel oil, JET

A or JP-8 fuels to avoid risk

of re or explosion. Never use

gasoline, oil drained from crank-

cases, naphtha, paint thinners,

alcohol or other highly am-

mable fuels.

Use only kerosene, #1/#2 diesel*/fuel oil,

JET A, JP-8 fuels. Heavier fuels such as No.

2 fuel oil, No. 2 diesel fuel may also be used

but will result in:

WARNING: Provide a fresh air

opening of at least three square

feet (2,800 square cm) for each

100,000 BTU/HR rating. Provide

extra fresh air if more heaters

are being used. The minimum

ventilation requirements must

be followed to avoid risks as-

sociated with carbon monoxide

poisoning. Make certain these

requirements are met prior to

operating heater.

www.usaprocom.com

160930-01A6

C

160111-02

5,567,144 D663,812

D663,813

D663,815

Standards/normes/Normas:

UL 733 - Fourth Edition

CSA-B140.0-03

CSA B140.8-1967

CSA C22.2 No.3-M1988

ASSEMBLED IN THE USA BY:

ASSEMBLE AUX ETATS-UNIS PAR:

ENSAMBLADA EN LOS EE.UU.POR:

PROCOM HEATING, INC.

2800 GRIFFIN DRIVE

BOWLING GREEN, KY 42101

40

50

60

70

80

90

THERMOSTAT F

THERMOSTATO F

O

START/RUN

ENCIENDA/OPERACION

DEMARRE/MARCHE

`

STANDBY

IMPORTANT: Review and un-

derstand the warnings in the

Safety section, pages 2 and 3.

They are needed to safely oper-

ate this heater. Follow all local

ordinances and codes when

using this heater.

TO START HEATER

1. Follow all ventilation and safety information.

2. Locate heater to provide maximum circu-

lation of the heated air. Follow all location

requirements noted in Safety, pages

2 and 3.

3. Fill fuel tank with fuel and attach fuel cap.

Use only kerosene, #1/#2 diesel/fuel oil,

JET A or JP-8 fuels to avoid risk of re or

explosion. Never use gasoline, oil drained

from crank cases, naphtha, paint thinners,

alcohol or other ammable fuels.

4. Plug heater’s power cord into approved,

grounded, three-wire extension cord.

Extension cord must be at least 6 feet

(1.8 m) long.

Extension Cord Size Requirement

• 6 to 10 feet (1.8 to 3 m) long, use 18

AWG (0.75 mm

2

) rated cord

• 11 to 100 feet (3.3 to 30.5 m) long, use

16 AWG (1.0 mm

2

) rated cord

• 101 to 200 feet (30.8 to 61 m) long, use

14 AWG (1.5 mm

2

) rated cord

5. Plug extension cord into standard 120

volt/60 hertz, 3-prong grounded outlet.

6. Turn thermostat knob to the desired tem-

perature setting.

If thermostat set temperature is higher

than the surrounding air temperature,

heater should ignite immediately. If heater

thermostat set temperature is lower than

surrounding air temperature, heater will

not ignite. Exposure to direct sunlight

or extreme cold may affect temperature

reading and/or thermostat operation.

The LED will ash for 8 seconds before

ignition. The LED will remain on during

heater operation, even if the heater is

cycled off by the thermostat. The LED will

ash rapidly if the heater shuts down for

any reason (Example: If out of fuel).

WARNING: This heater is

equipped with a thermostat.

Heater may start at any time.

TO STOP HEATER

1. Turn thermostat knob counterclockwise

to STANDBY.

2. Unplug heater when not in use.

TO RESET HEATER

1. Wait two minutes before restarting.

2. Turn thermostat knob to STANDBY for 10

seconds, then restart heater.

OPERATION

Figure 3 - Controls Display

Thermostat Knob

LED Light

www.usaprocom.com

7160930-01A

Ground Wire (#10 AWG -

Stranded-Copper)

Copper

or Brass

Grounding

Point

Figure 4 - Typical Generator Grounding

Method (Generator construction may

vary from that shown)

PREVENTATIVE MAINTENANCE SCHEDULE

WARNING: Never service heater while it is plugged in, operating

or hot. Severe burns and electrical shock can occur.

OPERATION WITH PORTABLE GENERATOR

Alternator

Ground Lug

WARNING: Before operating

heater or any appliance from a

portable generator, verify that

generator has been properly con-

nected to earth ground. Improper

grounding or failure to ground

generator can result in electro-

cution if a ground fault occurs.

Refer to owner’s manual supplied

by generator manufacturer for

proper grounding procedures.

Operating voltage range of heater is 95 to 135

Volts. Prior to plugging heater into generator

output voltage should be veried (if generator

is equipped with automatic idle feature, output

voltage should be measured with generator

running at full speed). If voltage does not

STORING, TRANSPORTING OR SHIPPING

3. Properly dispose of old and dirty fuel.

Check with local automotive service sta-

tions that recycle oil.

4. If storing, store heater in dry place. Make

sure storage place is free of dust and

corrosive fumes.

IMPORTANT: Do not store kerosene over

summer months for use during next heating

season. Using old fuel could damage heater.

measure in this range heater should not be

plugged into generator.

Refer to Operation, page 6, for starting, stop-

ping and resetting heater procedures.

Note: If shipping, transport companies require

fuel tanks to be empty.

1. Remove excess fuel from tank using a si-

phon pump. Drain remaining fuel through

ller neck by tipping heater to the rear.

2. If any debris is noted in old fuel, add 1 or 2

quarts of clean kerosene to tank, stir and

drain again. This will prevent excess debris

from clogging lters during future use.

Item How Often How To

Fuel tank Clean every season or as needed. See Storing, Transporting, or

Shipping, above.

Air output and

lint lters

Replace every 500 hours of operation or

once a year.

See Air Output, Air Intake and

Lint Filters, page 10.

Air intake lter Wash and dry with soap and water every 500

hours of operation or as needed.

See Air Output, Air Intake and

Lint Filters, page 10.

Fuel lter Clean twice a heating season or as needed. See Fuel Filter, page 11.

Fan blades Clean every season or as needed. See Fan, page 10.

Motor Not required/permanently lubricated.

www.usaprocom.com

160930-01A8

TROUBLESHOOTING

WARNING: Never service heater while it is plugged in, operating

or hot. Severe burns and electrical shock can occur.

WARNING: High voltage! Unplug heater before servicing.

FAULT CONDITION POSSIBLE CAUSE REMEDY

Motor does not start eight sec-

onds after heater is plugged in.

1. No power to heater.

2. Thermostat setting is too

low.

3. Bad electrical connection

between motor and ignition

control assembly or igni-

tion control assembly and

power cord.

4. Binding pump rotor.

5. Defective ignition control

assembly.

6. Defective motor.

1. Check circuit breaker in

electrical panel.

2. Turn thermostat knob to a

higher setting.

3. Check all electrical connec-

tions. See Wiring Diagram,

page 15.

4. If fan does not turn freely,

see Pump Rotor, page 14.

5. Replace ignition control as-

sembly. See Ignition Control

Assembly, page 13.

6. Replace motor.

Motor starts and runs but

heater does not ignite.

1. No fuel in tank.

2. Pump pressure incorrect.

3. Dirty fuel lter.

4. Obstruction in nozzle.

5. Water in fuel tank.

6. Bad electrical connection

between ignitor and ignition

control assembly.

7. Defective ignitor.

8. Defective ignition control

assembly.

1. Fill tank with kerosene.

2. See Pump Pressure Ad-

justment, page 11.

3. See Fuel Filter, page 11.

4. See Nozzle Assembly,

page 13.

5. Drain and ush fuel tank

with clean kerosene. See

Storing, Transporting, or

Shipping, page 7.

6. Check electrical connec-

tions. See Wiring Diagram,

page 15.

7.

Replace ignitor, see page 12.

8. Replace ignition control as-

sembly. See Ignition Control

Assembly, page 13.

www.usaprocom.com

9160930-01A

TROUBLESHOOTING

WARNING: High voltage! Unplug heater before servicing.

FAULT CONDITION POSSIBLE CAUSE REMEDY

Heater ignites but ignition

control assembly shuts heater

off after a short period of time.

1. Pump pressure incorrect.

2. Dirty air intake, air output,

and/or lint lter.

3. Dirty fuel lter.

4. Obstruction in nozzle.

5. Photocell assembly not

properly installed (not see-

ing the ame).

6. Dirty photocell lens.

7. Bad electrical connection

between photocell and

ignition control assembly.

8. Defective photocell.

9. Defective ignition control

assembly.

1. See Pump Pressure Ad-

justment, page 11.

2. See Air Output, Air Intake,

and Lint Filters, page 10.

3. See Fuel Filter, page 11.

4. See Nozzle Assembly,

page 13.

5. Make sure photocell boot is

properly seated in bracket.

6. Clean photocell lens.

7. Check electrical connec-

tions. See Wiring Diagram,

page 15.

8. Replace photocell.

9. Replace ignition control as-

sembly. See Ignition Control

Assembly, page 13.

SERVICE PROCEDURES

Figure 5 - Upper Shell Removal

WARNING: To avoid risk of

burn and electrical shock, never

attempt to service heater while it

is plugged in, operating, or hot.

UPPER SHELL REMOVAL

1. Remove screws along each side of heater

using 5/16" nut-driver. These screws at-

tach upper and lower shells together. See

Figure 5.

2. Lift upper shell off.

3. Remove fan guard.

www.usaprocom.com

160930-01A10

Motor

Shaft

Setscrew

Figure 6 - Fan, Motor Shaft, and

Setscrew Location

Motor

Shaft

Back of Flat on

Motor Shaft

1.82"

Motor

Shaft

Length

Fan

Setscrew

Touching

Back of Flat

on Motor

Shaft

Figure 7 - Fan Cross Section

Fan

Motor

AIR OUTPUT, AIR INTAKE AND

LINT FILTERS

1. Remove upper shell (see Figure 5, page 9).

2. Remove lter end cover screws using

5/16" nut-driver (see Figure 8).

3. Remove lter end cover.

4. Replace air output and lint lters.

5. Wash or replace air intake lter.

6. Replace lter end cover.

7. Replace fan guard and upper shell.

IMPORTANT: Do not oil lters.

Air Intake

Filter

Lint Filter

Filter

End

Cover

Air Output

Filter

Figure 8 - Air Output, Air Intake, and Lint

Filters

SERVICE PROCEDURES

FAN

IMPORTANT: Remove fan from motor shaft

before removing motor from heater. The

weight of the motor resting on the fan could

damage the fan pitch (see Figure 6).

1. Remove upper shell (see Figure 5, page 9).

2. The fan is located with the set screw in

contact with the back of at on motor as

shown in Figure 7.

3. Use 1/8" Allen wrench to loosen setscrew

which holds fan to motor shaft (see Fig-

ure 6).

4. Slip fan off motor shaft.

5. Clean fan using a soft cloth moistened

with kerosene or solvent.

6. Dry fan thoroughly.

7. Place setscrew on flat of shaft.

Tighten setscrew firmly (40-50 inch-

pounds/4.5-5.6 n-m).

8. Replace fan guard and upper shell.

www.usaprocom.com

11160930-01A

SERVICE PROCEDURES

PUMP PRESSURE

ADJUSTMENT

1. Remove pressure gauge plug from lter

end cover (see Figure 9).

2. Install 0-15 PSI pressure gauge.

3. Start heater (see Operation, page 6). Al-

low heater to reach operating temperature

(approx. 10 minutes).

4. Adjust pressure. Turn relief valve to right

to increase pressure. Turn relief valve to

left to decrease pressure. See specica-

tions in Figure 10 for correct pressure.

5. Remove pressure gauge. Replace pres-

sure gauge plug in lter end cover.

Figure 9 - Pressure Gauge Plug Removal

Pressure

Gauge

Plug

Pressure

Gauge

Figure 10 - Adjusting Pump Pressure

Relief

Valve

Fuel Filter,

Bushing, and

Lower Fuel Line

Upper Fuel Line

Side Cover

Figure 11 - Fuel Filter Removal

FUEL FILTER

1. Remove side cover screws using 5/16"

nut-driver.

2. Remove side cover.

3. Pull upper fuel line off fuel lter neck (see

Figure 11).

4. Carefully pry bushing, fuel lter, and lower

fuel line out of fuel tank (see Figure 11).

5. Wash fuel lter with clean fuel and replace

in tank.

6. Attach upper fuel line to fuel lter neck.

7. Replace side cover.

Pump

Model Pressure

80 3.8 PSI

145 6.8 PSI

220 8.4 PSI

www.usaprocom.com

160930-01A12

IGNITOR

1. Remove upper shell and fan guard (See

Upper Shell Removal, page 9.

2. Remove fan (see page 10).

3. Remove the control side cover with a

5/16" nut driver. Remove side cover (see

Figure 12).

4. Disconnect ignitor wires from ignition

control assembly (see Figure 12). Pull

the ignitor wires up through the hole in

the lower shell.

5. Disconnect fuel line hose and air line

hose. Remove photocell from photocell

bracket (see Figure 12).

6. Remove combustion chamber. Stand

combustion chamber on end with nozzle

adapter bracket on top (see Figure 13).

7. Remove ignitor screw with a 1/4" nut

driver. Carefully remove ignitor from

nozzle adapter bracket.

CAUTION: Do not bend or

strike ignitor element. Handle

with care.

8. Carefully remove replacement ignitor from

packing.

9. Carefully guide ignitor into opening in

nozzle adapter bracket. Do not strike

ignitor element. Attach ignitor to nozzle

adapter bracket with screw using a 1/4"

nut driver. Torque 0.90 to 1.69 N-m (8 to

15 in-lbs) Do not over torque.

10. Replace combustion chamber.

11. Route the ignitor wires back down through

the hole in the lower shell. Connect wires

to the ignition control assembly (see Fig-

ure 12).

12. Replace control side cover.

13. Connect and route fuel line hose and air

line hose to nozzle adapter assembly.

14. Replace photocell in photocell bracket.

15. Replace fan (see page 10).

16. Replace fan guard and upper shell (see

pages 9 and 10).

SERVICE PROCEDURES

Photocell

Bracket

Ignitor

Ignitor Screw/

Washer Assembly

Nozzle

Adapter

Bracket

Ignitor

Element

Combustion

Chamber

Nozzle Adapter

Bracket Opening

Figure 13 - Ignitor SP002-01

Replacement

Figure 12 - Disconnecting Ignitor Wires

from Ignition Control Assembly

Photocell

Bracket

Air Line

Hose

Fuel

Line

Hose

Combustion

Chamber

Photocell

Assembly

Ignitor

Nozzle Adapter

Bracket

Ignition

Control

Assembly

Side Cover

Ignitor

Wire

www.usaprocom.com

13160930-01A

Figure 14 - Removing Air and Fuel Line

Hoses

Fuel Line

Hose

Air Line

Hose

Nozzle/

Adapter

Assembly

Combustion

Chamber

Photocell

Bracket

Nozzle

Adapter

Bracket

NOZZLE ASSEMBLY

1. Remove upper shell (see Upper Shell

Removal, page 9).

2. Remove fan (see Fan, page 10).

3. Remove fuel and air line hoses from

nozzle assembly (see Figure 14).

4. Turn nozzle assembly 1/4 turn to left and

pull toward motor to remove (see Figure

15).

5. Place plastic hex-body into vise and

lightly tighten.

6. Carefully remove nozzle from the nozzle

adapter using 5/8" socket wrench (see

Figure 16).

7. Blow compressed air through face of

nozzle. This will free any dirt in nozzle

area.

8. Inspect nozzle sleeve for damage.

9. Replace nozzle into nozzle adapter until

nozzle seats. Tighten 1/3 turn more using

5/8" socket wrench 4.5 to 5.1 N-m (40 to

45 in-lbs). See Figure 16.

10. Attach nozzle assembly to burner strap

(see Figure 15).

11. Attach fuel and airline hoses to nozzle

assembly.

12. Replace fan (see Fan, page 10).

13. Replace fan guard and upper shell (see

Upper Shell Removal, page 9).

Figure 15 - Removing Nozzle/Adapter

Assembly

Nozzle/

Adapter

Assembly

Combustion

Chamber

Figure 16 - Nozzle and Nozzle Adapter

Nozzle Face

Nozzle

Nozzle Sleeve

Nozzle

Adapter

Air Line

Fitting

Fuel Line

Fitting

SERVICE PROCEDURES

IGNITION CONTROL ASSEMBLY

WARNING: High voltage!

1. Unplug heater.

2. To expose the ignition control assembly,

remove the control panel side cover

screws using 5/16" nut-driver.

3. Remove old ignition control assembly.

Install new ignition control assembly (see

Figure 12, page 12).

4. Replace control panel side cover.

www.usaprocom.com

160930-01A14

PUMP ROTOR

(Procedure if Rotor is Binding)

1. Remove upper shell (see Upper Shell

Removal, page 9).

2. Remove filter end cover screws using

5/16" nut driver (see Figure 17).

3. Remove filter end cover and air filters.

4. Remove pump plate screws using 5/16"

nut-driver.

5. Remove pump plate.

6. Remove rotor, insert, and blades (see

Figure 18).

7. Check for debris in pump. If debris is

found, blow out with compressed air.

8. Install insert and rotor.

9. Check gap on rotor. Adjust to

0.076/0.101 mm (0.003"/0.004") if needed

(see Figure 18).

Note: Rotate rotor one full turn to ensure

the gap is 0.076/0.101 mm (0.003"/0.004")

at tightest position. Adjust if needed.

10. Install blades, pump plate, air filters, and

filter end cover.

11. Replace fan guard and upper shell (see

Upper Shell Removal, page 9).

12. Adjust pump pressure (see Pump Pres-

sure Adjustment, page 11).

Note: If rotor is still binding, proceed as

follows.

13. Perform steps 1 through 6.

14. Place fine grade sandpaper (600 grit) on

flat surface. Sand rotor lightly in “figure 8”

motion four times (see Figure 19).

15. Reinstall insert and rotor.

16. Perform steps 10 through 12.

Figure 17 - Rotor Location

Pump

Cover

Insert

Rotor

Blade

Filter

End

Cover

Air

Intake

Filter

Air Output Filter

Gap Adjusting Screw

Rotor

Blade

0.003"/0.004"

(0.076-0.101 mm)

Gap Measured

With Feeler

Gauge

Gap Adjusting Screw

Figure 18 - Gap Adjusting Screw

Locations

Sandpaper

Figure 19 - Sanding Rotor

SERVICE PROCEDURES

Pump

Plate

www.usaprocom.com

15160930-01A

WIRING DIAGRAM

ST002-01

AIR GAUGE KIT

Special tool to check pump pressure.

0-15 PSI gauge. 3/8" NPT pipe thread.

ST001-01

IGNITION CONTROL ASSEMBLY/

PHOTOCELL TESTER

Special tool used to test the ignition control

assembly and photocell.

ACCESSORIES

Purchase these accessories from your local dealer. If they can not supply these accessories,

contact ProCom Heating, Inc. at 1-866-573-0674 for information. You can also write to the

address listed on the back page of this manual.

TECHNICAL SERVICE

You may have further questions about installation, operation, or troubleshooting. If so, contact

ProCom Heating, Inc. at 1-866-573-0674. When calling, please have your model and serial

numbers of your heater ready.

You can also visit ProCom Heating, Inc.’s web site at www.usaprocom.com.

Photocell

Thermostat Control

Photocell

Temp

Heater Control Assembly

Ignitor RET

Motor

White

Green

to Shell

Ignitor

Black

Power Plug

120V/60Hz

Red

Neutral (N)

120V (L1)

Motor Red

Ignitor

www.usaprocom.com

160930-01A16

PARTS

MODELS PPK80T, PPK145T & PPK220T

28

29

12

13

14

24

23

22

25

26

27

1

3

18

33

19

30

31

17

16

15

17

21

20

7

8

10

6

9

11

2

4

5

34

32

www.usaprocom.com

17160930-01A

PARTS

MODELS PPK80T, PPK145T & PPK220T

This list contains replaceable parts used in your heater. When ordering parts, be sure to pro-

vide correct model and serial numbers (from model plate), and part number and description

of desired part.

Key PPK80T PPK145T PPK220T Description QTY

1 160075-01 160075-02 160075-03 Wire Guard 1

2 ** ** ** Shell Screw 8 or 10

3 ** ** ** Upper Shell 1

4 ** ** ** Combustion Chamber Assy 1

5 ** ** ** Lower Shell 1

6 see detail, page 19 Nozzle Bracket Assembly

7 160011-01 160058-01 160058-01 Fan 1

8 see detail, page 18 Motor/Pump Assembly

9 see detail, page 19 Photocell/Bracket Assembly

10 160043-01 160043-02 160043-02 Motor Mounting Bracket 1

11 160066-01 160066-02 160066-02 Fan Guard 1

12 160012-02 160012-01 160012-01 Fuel Filter 1

13 ** ** ** Fuel Tube Bushing 1

14 160038-01 160038-02 160038-02 Lower Fuel Line 1

15 160037-02 160037-02 160037-02 Airline Tubing 1

16 160039-01 160039-01 160039-01 Upper Fuel Line 1

17 ** ** ** Shell Bracket 2

18 160184-01 160184-02 160184-02 Right Side Cover 1

19 160183-01 160183-02 160183-02 Left Side Cover 1

20 113471-02 113471-02 113471-02 LED Thermostat Control 1

21 160190-01 160190-01 160190-01 Thermostat Control Bracket 1

22 160013-01 160013-01 160013-01 Strain Relief Bushing 1

23 160021-01 160021-01 160021-01 Power Supply Cord 1

24 160030-01 160030-01 160030-01 Vented Fuel Cap Assy. 1

25 160030-03 160030-03 160030-03 Vented Fuel Cap Gasket 1

26 160031-01 160031-01 160031-01 Plastic Filler Neck 1

27 160036-01 160036-01 160036-01 Filler Neck Gasket 1

28 160005-01 160005-02 160005-02 Fuel Gauge 1

29 160139-01BK 160140-01BK 160141-01BK Fuel Tank Assembly 1

30 ** ** ** Shorty Bushing .512 1

31 ** ** ** Shorty Bushing .866 1

32 160185-01 ---- ---- Plastic Handle 1

160186-01 ---- ---- Handle Bracket 1

33 160027-01 160027-01 160027-01 Control Knob 1

34 ** ** ** Clip, Nut, #10, .030 Wall 8 or 10

** Not a eld replaceable part.

www.usaprocom.com

160930-01A18

13

12

17

11

10

9

8

7

6

5

4

3

2

18

1

16

19

15

14

ITEM PART # DESCRIPTION QTY

1 160001-01 Motor 1

2 160023-01 Rotor Insert 1

3 160003-02 Pump Rotor 1

4 160006-01 Pump Body 1

5 160088-01 Screw, 10-32 x .62 2

6 160007-01 Pump Cover 1

7 160009-01 Lint Filter 1

8 160008-01 Output Filter Assembly 1

9 160010-01 Intake Filter 1

10 160057-01 Filter End Cover 1

11 160025-01 Adjusting Screw 1

12 160024-01 Pipe Plug 1

13 160090-01 Screw, 10-32 x 1.0 3

14 160089-01 Screw, 10-32 x 1.12 6

15 160029-01 90° Nylon Elbow 1

16 160004-01 Pump Blade 4

17 160052-01 Pressure Relief Spring 1-2

18 160053-01 Steel Ball 1

19 160189-01 Pump Plate 1

PARTS

MOTOR AND PUMP ASSEMBLY

MODELS PPK80T, PPK145T & PPK220T

www.usaprocom.com

19160930-01A

PHOTOCELL ASSEMBLY

MODELS PPK80T, PPK145T & PPK220T

1

2

3

ITEM PART # DESCRIPTION QTY

1 160041-03 Photocell Bracket 1

2 160092-02 Screw, 6-32 x .38 2

3 160016-01 Photocell Assembly 1

NOZZLE ASSEMBLY

PARTS

MODELS PPK80T & PPK145T MODEL PPK220T

2

4

5

6

9

7

11

3

2

4

5

6

10

9

8

7

3

1

Item PPK80T PPK145T PPK220T Description Qty

1 ---- ---- 160086-01 Stainless Steel Retaining Ring 1

2 160042-01 160042-01 160042-02 Nozzle Adapter Bracket 1

3 160102-01 160102-01 160102-01 Screw, 10-16 x .38 1

4 160002-01 160002-01 160002-01 Ignitor 1

5 160093-01 160093-01 160093-01 Belleville Washer 1

6 160092-01 160092-01 160092-01 Screw, 6-32 X .88 1

7 160040-32 160040-24 160040-41 Nozzle Assembly 1

8 ---- ---- 160077-01 Barb Fitting 1

9 160028-01 160028-01 160028-02 Nozzle Adapter 1

10 ---- ---- 160077-02 Barb Fitting, 90° 1

11 160040-E 160040-E 160040-E O-Ring 1

www.usaprocom.com

160930-01A20

PARTS

WHEEL AND HANDLES

MODELS PPK145T & PPK220T

1

3

5

4

6

7

8

9

2

ITEM PART # DESCRIPTION QTY

1 160074-01 Rear Handle 1

2 160079-01 Axle 1

3 160072-01 Wheel Support Frame 2

4 160158-01 Support Bushing 2

5 160072-12 Fuel Tank Support Assembly 1

6 160072-13 Screw, M10-1.5 x 60 2

7 160129-01 Acorn Nut 2

8 160080-01 Wheel 2

9 160130-01 Wheel Spacer 2

La page charge ...

ProCom Heating PPK80T Manuel utilisateur

Ce manuel convient également à

ProCom Heating PPK80T Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents