Venstar 1DX Manuel utilisateur

Marque: Venstar

Modèle: 1DX

Taper: Manuel utilisateur

Venstar – 1DX

1DX – Manual

FCC ID of this product is as follows.

FCC ID: MUH-DAlKlN1P2

IC ID: 12547A-DAIKIN1P2

For OEM integration only — device cannot be sold to general public. Therefore we

will ask OEM to include the following statements required by FCC on the product

and in the installation manual notice.

Contents

1. Voltage

2. Antenna

3. Notice

Venstar – 1DX

1. Supply Voltage

Min.

Typ.

Max.

Unit

Specification Temperature Range

-40

+25

+85

deg.C

Specification Voltage

VBAT

3.0

3.6

4.8

VDDIO

1.71

1.8or3.3

3.63

2. Antenna

Please perform the antenna design that followed the specifications of the

antenna.

The concrete contents of a check are the following three points.

1) It is the same type as the antenna type of antenna specifications.

Confirm the same size as the Gerber file.

2) An antenna gain is lower than a gain given in antenna specifications.

Measure the gain, and confirm the peak gain is less than the application value

(1.4dBi) 3) The emission level is not getting worse.

Measure the spurious, and confirm degradation of less than 3dB than spurious

value of worst of report used for the application. However it is spurious defined

below.

Please send those reports to Venstar

Venstar – 1DX

3. Notice

For OEM integration only — device cannot be sold to general public. Therefore we will ask OEM

to include the following statements required by FCC/IC on the product and in the Installation

manual Notice.

Please describe the following warning on the final product which contains this module.

Certification labelling guidance:

This device contains FCC ID: MUH-DAIKIN1P2

This device contains IC: 12547A-DAIKIN1P2

Contains FCC ID: MUH-DAIKIN1P2

Contains IC: 12547A-DAIKIN1P2

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) this device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired

operation.

Changes or modifications not expressly approved by Venstar could void the user's

authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help

Venstar – 1DX

This device contains licence-exempt transmitter(s)/receiver(s) that comply with

Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).

Operation is subject to the following two conditions:

1. This device may not cause interference.

2. This device must accept any interference, including interference that may cause

undesired operation of the device.

L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme

aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux

appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions

suivantes :

1. L’appareil ne doit pas produire de brouillage;

2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est

susceptible d’en compromettre le fonctionnement

This radio transmitter 12547A-DAIKIN1P2 has been approved by Innovation, Science and

Economic Development Canada to operate with the antenna types listed below, with the

maximum permissible gain indicated. Antenna types not included in this list that have a

gain greater than the maximum gain indicated for any type listed are strictly prohibited

for use with this device.

Le présent émetteur radio 12547A-DAIKIN1P2 a été approuvé par Innovation, Sciences et

Développement économique Canada pour fonctionner avec les types d'antenne

énumérés ci-dessous et ayant un gain admissible maximal. Les types d'antenne non

inclus dans cette liste, et dont le gain est supérieur au gain maximal indiqué pour tout

type figurant sur la liste, sont strictement interdits pour l'exploitation de l'émetteur.

Please perform the antenna design that followed the specifications of the antenna.

The concrete contents of a check are the following three points.

1) It is the same type as the antenna type of antenna specifications. Confirm the same size

as the Gerber file.

2) An antenna gain is lower than a gain given in antenna specifications. Measure the gain,

and confirm the peak gain is less than the application value (1.4dBi)

3) The emission level is not getting worse. Measure the spurious, and confirm degradation

of less than 3dB than spurious value of worst of report used for the application.

However, it is spurious defined below.

Please send those reports to Venstar

Venstar 1DX Manuel utilisateur

Marque: Venstar

Modèle: 1DX

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Venstar 1DX User manual

Documents connexes

Venstar ACC-VNTH1 Manuel utilisateur

Venstar 1DX Manuel utilisateur

Venstar 1DX Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents