Vulcan-Hart SG4D ML-114875 Manuel utilisateur

Marque: Vulcan-Hart

Modèle: SG4D ML-114875

Catégorie: Micro-ondes

Taper: Manuel utilisateur

Ce manuel convient également à

SG SERIES GAS SNORKEL™

CONVECTION OVENS

MODELS

SG4D ML-114875

SG4C ML-114876

SG6D ML-114877

SG6C ML-114878

INSTALLATION &

OPERATION MANUAL

P.O. BOX 696, LOUISVILLE, KY 40201-0696

TEL. (502) 778-2791

FORM 35624 REV. A (08-04)

(Formerly F-31024 & F-33220)

VULCAN-HART

DIVISION OF ITW FOOD EQUIPMENT GROUP, LLC

WWW.VULCANHART.COM

For additional information on Vulcan-Hart or to locate an authorized parts

and service provider in your area, visit our website at www.vulcanhart.com

— 2 —

IMPORTANT FOR YOUR SAFETY

THIS MANUAL HAS BEEN PREPARED FOR PERSONNEL QUALIFIED TO INSTALL GAS

EQUIPMENT, WHO SHOULD PERFORM THE INITIAL FIELD START-UP AND

ADJUSTMENTS OF THE EQUIPMENT COVERED BY THIS MANUAL.

POST IN A PROMINENT LOCATION THE INSTRUCTIONS TO BE FOLLOWED IN THE

EVENT THE SMELL OF GAS IS DETECTED. THIS INFORMATION CAN BE OBTAINED

FROM THE LOCAL GAS SUPPLIER.

IMPORTANT

IN THE EVENT A GAS ODOR IS DETECTED, SHUT

DOWN UNITS AT MAIN SHUTOFF VALVE AND

CONTACT THE LOCAL GAS COMPANY OR GAS

SUPPLIER FOR SERVICE.

FOR YOUR SAFETY

DO NOT STORE OR USE GASOLINE OR OTHER

FLAMMABLE VAPORS OR LIQUIDS IN THE

VICINITY OF THIS OR ANY OTHER APPLIANCE.

WARNING

IMPROPER INSTALLATION, ADJUSTMENT,

ALTERATION, SERVICE OR MAINTENANCE CAN

CAUSE PROPERTY DAMAGE, INJURY OR DEATH.

READ THE INSTALLATION, OPERATING AND

MAINTENANCE INSTRUCTIONS THOROUGHLY

BEFORE INSTALLING OR SERVICING THIS

EQUIPMENT.

IN THE EVENT OF A POWER FAILURE, DO NOT

ATTEMPT TO OPERATE THIS DEVICE.

— 3 —

TABLE OF CONTENTS

GENERAL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Installation Codes and Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Installing Basic Oven . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Assembling Stacked Ovens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Leveling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Electrical Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Gas Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Testing the Gas Supply System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Vent System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Controls — Models SG4D and SG6D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Before First Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Lighting the SG4D and SG6D Ovens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Using the SG4D and SG6D Ovens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Controls — Models SG4C and SG6C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Before First Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Lighting the SG4C and SG6C Ovens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Using the SG4C and SG6C Ovens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Error Messages — SG4C and SG6C Ovens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Roast and Hold Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Rack Arrangements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Conserving Energy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Cooking Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

High Limit Switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Vent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Replacing Lamps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Service and Parts Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

TROUBLESHOOTING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

— 4 —

Installation, Operation and Care of

MODEL SG4D, SG4C, SG6D & SG6C

GAS SNORKEL™ CONVECTION OVENS

PLEASE KEEP THIS MANUAL FOR FUTURE USE

GENERAL

Vulcan Gas Snorkel™ Convection Ovens are produced with quality workmanship and material. Proper

installation, usage and maintenance of your oven will result in many years of satisfactory performance.

It is suggested that you thoroughly read this entire manual and carefully follow all of the instructions

provided.

Models SG4D and SG6D feature a solid state temperature control, 1-hour dial timer with buzzer, two-

speed 1/3 HP (0,25 kw) blower motor and porcelain interior as standard equipment. Each SG4D and

SG4C oven is equipped with a 60,000 BTU/hr. burner.

Models SG4C and SG6C are equipped with electronic time and temperature controls, two-speed 1/3 HP

(0,25 kw) blower motor, a roast-and-hold feature, and porcelain interior as standard equipment. Each

SG6D and SG6C oven is equipped with a 60,000 BTU/hr. burner.

Models SG6D and SG6C have a deeper oven cavity.

Models SG44D, SG44C, SG66D, and SG66C consist of two single ovens and are supplied with a

stacking kit for mounting one oven on top of the other.

All ovens are equipped with a power level control which permits variation of the heat input between 22%

and 100% of full input.

All standard 120 volt ovens require single phase electrical service and are equipped with a 3 prong

grounding plug.

Oven doors open independently and all ovens are furnished with 5 racks.

Available options are simultaneous oven door opening, a 5-hour timer, 208/240 volt electrical service

with hard wire connection direct to the terminal block supplied with the oven, additional oven racks, and

an open stand with lower storage rack.

FEATURES

Thermostat Timer Stack Roast &

Model (Each Oven) (Each Oven) Kit Hold Legs

SG4D/SG6D Solid State 1-Hour Dial 253/4" (654 mm)

SG44D/SG66D Solid State 1-Hour Dial X 8" (203 mm)

SG4C/SG6C Electronic Electronic X 253/4" (654 mm)

SG44C/SG66C Electronic Electronic X X 8" (203 mm)

— 5 —

INSTALLATION

Before installing, verify that the electrical service and type of gas supply (natural or propane) agree with

the specifications on the rating plate located behind the top trim panel on the front of the oven. If the

supply and equipment requirements do not agree, do not proceed with the installation. Contact your

dealer or Vulcan-Hart immediately.

UNPACKING

This oven was inspected before leaving the factory. The transportation company assumes full

responsibility for safe delivery upon acceptance of the shipment. Immediately after unpacking, check

for possible shipping damage. If the oven is found to be damaged, save the packaging material and

contact the carrier within 15 days of delivery.

Carefully unpack oven and place in a work-accessible area as near to its final installed position as

possible.

Do not use the doors or their handles to lift the oven.

LOCATION

The equipment area must be kept free and clear of combustible substances.

When installed, minimum clearance from combustible construction must be 1" (25 mm) at the left side

4" (102 mm) at the right side, and 6" (152 mm) at the rear. Minimum clearance from noncombustible

construction must be 0" at the left side, 4" at the right side and 6" (152 mm) at the rear. The oven may

be installed on combustible floors.

The installation location must allow adequate clearances for servicing and proper operation.

The oven must be installed so that the flow of combustion and ventilation air will not be obstructed.

Adequate clearance for air openings into the combustion chamber must be provided. Make sure there

is an adequate supply of air in the room to allow for that required for combustion of gas at the oven

burners.

Do not permit fans to blow directly at the oven. Wherever possible, avoid open windows next to the

oven. Avoid wall-type fans which create air cross currents within the room.

— 6 —

INSTALLATION CODES AND STANDARDS

Vulcan ovens must be installed in accordance with:

In the United States of America:

1. State and local codes.

2. National Fuel Gas Code, ANSI-Z223.1 (latest edition). Copies may be obtained from The American

Gas Association, Inc., 1515 Wilson Blvd., Arlington, VA 22209.

3. National Electrical Code, ANSI/NFPA-70 (latest edition). Copies may be obtained from The

National Fire Protection Association, Batterymarch Park, Quincy, MA 02269.

In Canada:

1. Local codes.

2. CSA B149.1 Natural Gas and Propane Installation Code.

3. CSA C22.1 Canadian Electrical Code.

The above are available from the Canadian Standard Association, 5060 Spectrum Way, Suite 100,

Mississauga, Ontario, Canada L4W 5N6.

INSTALLING BASIC OVEN

The basic oven must be installed on legs, casters or mounted on a modular stand. Installations on

concrete bases or other supports restricting air circulation underneath the oven is not advisable and

may void the warranty.

Ovens Mounted on Casters

Ovens mounted on casters must use a flexible connector

(not supplied by Vulcan) that complies with the Standard for

Connectors for Movable Gas Appliances, ANSI Z21.69 •

CSA 6.16 and a quick-disconnect device that complies with

the Standard for Quick-Disconnect Devices for Use With

Gas Fuel, ANSI-Z21.41 • CSA 6.9. In addition, adequate

means must be provided to limit movement of the appliance

without depending on the connector and the quick-disconnect

device or its associated piping to limit appliance movement.

Attach the restraining device at the rear of the oven as

shown in Fig. 1.

If disconnection of the restraint is necessary, turn off the gas

supply before disconnection. Reconnect this restraint prior

to turning the gas supply on and returning the oven to its

installation position.

Separate instructions for installing casters to the oven are

included with the casters.

Note: If the oven is installed on casters and is moved for any reason, it is recommended that the oven

be releveled front to back and side to side for even baking.

Fig. 1

CONNECT GAS

LINE STRAIN

RELIEF HERE

PL-52805

— 7 —

Assembling the Legs to the Oven

The legs must be installed on the bottom of the oven. Position oven on its back, taking care not to

scratch or damage it. The gas pipe connection protrudes beyond the back; provide for this when the

oven is tipped back by resting it on suitable spacers (2 x 4's [51 x 102 mm], etc.).

Attach each of the four leg assemblies to the bottom of the oven with the 24 bolts and lockwashers

(6 per leg). Carefully raise the oven to its normal position.

Assembling the Stand to the Oven

Attach each of the four leg assemblies to the bottom of the oven with the 24 bolts and lockwashers

(6 per leg). Carefully raise the oven to its normal position.

Attach the undershelf to the legs with 8 bolts and lockwashers (2 per leg).

Install the rack guides into the shelf at desired locations (for pan or flat rack), then attach the rack

supports to the top end of the rack guides. Attach rack supports to the leg assembly by removing one

middle bolt and reattaching back through the end holes in the rack support. (Fig. 2)

Fig. 2

BACK

FRONT

PL-52821

— 8 —

ASSEMBLING STACKED OVENS

Unpack the ovens and stack kit. Position the oven to be used as the bottom oven on its back for access

to the oven bottom, taking care not to scratch or damage it. The gas pipe protrudes beyond the back;

provide for this when the oven is tipped back by resting it on suitable spacers (2 x 4's [51 x 102 mm],

etc.). Attach the four leg assemblies with the 24 bolts and lockwashers (6 per leg).

Place the lower oven (with legs/casters) on the floor and remove two 7/16" (11 mm) diameter knockouts

on each side of the top cover. Remove vent guard and discard it.

Move the oven (with legs/casters) to the installed position and place upper oven on top of lower oven

using the locating studs.

Remove the rear panel from the TOP oven. Install the two-piece stacking common flue (Fig. 3) with

the four screws provided. Replace the top oven rear panel.

Connect the piping between the top oven and bottom oven. Pipe compound must be suitable for the

type of gas being used (natural or propane).

Fig. 3

VENT GUARD

TWO PIECE

STACKING

COMMON FLUE

PL-52884

— 9 —

LEDOM

ATADSAG LACIRTCELE

ATAD

RH/TUBTUPNIERUSSERPDLOFINAMENILPMA

larutaNenaporPlarutaNenaporPstloV021

C/D4GS

C/D6GS 000,06000,06"5.3"01spmA9

C/D44GS

C/D66GS 000,021000,021"5.3"01spmA81

The manual gas valve, located behind the small door in the lower front panel, should remain off until

all electrical and gas connections are made and the ovens are ready to be used.

LEVELING

Ensure that the oven racks are level in the final installed position. If the oven is installed on legs, turn

the adjustable feet in or out to level the oven front-to-back and side-to-side.

ELECTRICAL CONNECTIONS

WARNING: ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE

APPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCAL

ELECTRICAL CODES.

WARNING: APPLIANCES EQUIPPED WITH FLEXIBLE ELECTRICAL POWER SUPPLY CORD

ARE PROVIDED WITH A THREE-PRONG GROUNDING PLUG. IT IS IMPERATIVE THAT THIS

PLUG BE CONNECTED INTO A PROPERLY GROUNDED THREE-PRONG RECEPTACLE. IF THE

RECEPTACLE IS NOT THE PROPER GROUNDING TYPE, CONTACT AN ELECTRICIAN. DO NOT

REMOVE THE GROUNDING PRONG FROM THIS PLUG.

The SG series ovens are equipped with a 120 volt / 60 Hz. / 1 phase cord and plug.

Refer to the Installation Codes and Standards section of this manual.

A schematic decal is located on the inside of the right side panel.

GAS AND ELECTRICAL DATA

3.5" (0.87 kPa) 10" (2.49 kPa)

— 10 —

GAS CONNECTIONS

Gas supply connections and any pipe joint compound must be resistant to the action of propane gases.

Location of the gas inlet is at the rear of the oven. Codes require that a gas shutoff valve must be

installed in the gas line ahead of the oven.

Connect gas supply after leveling the oven. The gas supply line must be at least the equivalent of

(19mm) iron pipe. Make sure the pipes are clean and free of obstructions, dirt, or pipe joint

compound.

The ovens are equipped with fixed burner orifices which match with installation elevation.

The oven is provided with a regulator integral to the gas solenoid valve and requires no external

regulator.

Natural gas pressure regulators are preset for 3.5" W.C. (Water Column) (0.87 kPa); propane gas

pressure regulators are preset for 10" W.C. (2.49 kPa).

WARNING: PRIOR TO LIGHTING, CHECK ALL JOINTS IN THE GAS SUPPLY LINE FOR LEAKS.

USE SOAP AND WATER SOLUTION. DO NOT USE AN OPEN FLAME.

After piping has been checked for leaks, all piping receiving gas should be fully purged to remove air.

TESTING THE GAS SUPPLY SYSTEM

When gas supply pressure exceeds 1/2 psig (3.45 kPa), the oven and its individual shutoff valve must

be disconnected from the gas supply piping system.

When gas supply pressure is 1/2 psig (3.45 kPa) or less, the oven should be isolated from the gas supply

system by closing its individual manual shutoff valve.

ADJUSTMENTS

Air Adjustment

Although main burner air is adjusted before shipment, it should be checked at the time of installation.

Excessive air will cause flames to lift off a burner when cold or may cause flash-back during normal

cycling of oven, particularly when propane gas is used.

Insufficient air will cause flames to burn with a yellow tip and result in carbon accumulation in the flame

chamber and heat exchanger tubes.

Contact your local Vulcan-Hart servicer if required.

— 11 —

VENT SYSTEM

DO NOT obstruct the flow of flue gases from the flue located on the rear of the oven. It is recommended

that the flue gases be ventilated to the outside of the building through a ventilation system installed by

qualified personnel.

Ovens may use an optional down draft diverter flue method. This optional down draft diverter must be

purchased from the oven manufacturer and vented to the outside; otherwise, the installation of any

such devise will void all oven certifications and warranties. When the diverter is supplied, it may be

connected to a Type “B” vent.

From the termination of the flue to the filters of the hood venting system, a minimum clearance of

18" (457mm) must be maintained.

Information on the construction and installation of ventilating hoods may be obtained from the standard

for "Vapor Removal from Cooking Equipment," NFPA No. 96 (latest edition), available from the

National Fire Protection Association, Batterymarch Park, Quincy, MA 02269.

— 12 —

OPERATION

WARNING: THE OVEN AND ITS PARTS ARE HOT. BE VERY CAREFUL WHEN OPERATING OR

CLEANING THE OVEN.

CONTROLS — MODELS SG4D AND SG6D (Fig. 4)

Fig. 4

— 13 —

Master Switch — ON — turns oven control circuits on.

OFF — turns oven control circuits off.

OVEN COOL — allows the fan motor to run with the doors ajar to

speed oven cooling.

On Light (Amber) — Lit when Master Switch is positioned at ON.

Heat Light (White) — Comes on and goes off when the burner cycles on and off.

No Ignition Light (Red) — Comes on if burner fails to ignite. When lighting the oven, the No

Ignition Light flashes.

Thermostat — Controls oven temperature during cooking operation.

Power Level Control — A potentiometer which permits variation of the heat input between

22% and 100% of full input.

Dial Setting Percent of Full Input

10 100%

9 77%

8 73%

7 68%

6 60%

5 53%

4 45%

3 37%

2 28%

1 22%

One-Hour Timer — Use to set cooking cycle time. Alarm sounds continuously when

elapsed time counts down to 0; oven does not turn off. Turn timer

to OFF position to stop alarm. When oven is not in use, keep timer

at OFF position.

Two-Speed Fan Switch — Adjusts air velocity in the oven.

Light Switch — Turns lights in the oven on or off.

BEFORE FIRST USE

Before using the oven for the first time, it must be "burned in" to release any odors that might result from

heating the new surfaces in the chamber.

1. Using a clean damp cloth, wipe the inside of the oven, including the racks.

2. Close the oven doors, push the Master Switch to ON, turn the Thermostat to 300°F (149°C), and

allow the oven to cycle for 6 to 8 hours before pushing the Master Switch OFF.

— 14 —

LIGHTING THE SG4D AND SG6D OVENS

1. Turn the main gas supply ON.

2. Turn the gas control valve (located behind the small door on the lower front panel) ON.

3. Push the Master Switch to ON and turn Thermostat to its maximum setting. Both the ON and HEAT

lights should come on. If HEAT light is not on, make sure the oven door(s) are closed.

4. If the oven fails to light, the red No Ignition light will be lit and remain on. Push Master Switch to OFF.

Turn gas off.

5. Wait 5 minutes before repeating Steps 1 through 4.

If the oven does not light after three trials, turn off the main gas valve and call a qualified servicer.

USING THE SG4D AND SG6D OVENS

Preheating

1. Select the proper rack arrangement for the product to be cooked. (See RACK ARRANGEMENTS

in this manual.)

2. Make sure the doors are closed.

3. Push Master Switch to ON. The amber ON light will come on, indicating that power to the oven is

on.

4. Set the Power Level Control to 10.

5. Set the two-speed Fan Switch to the desired setting.

6. Set Thermostat as desired. The Heat light will come on and remain on until the oven reaches set

temperature (approximately 10 to 15 minutes for settings from 300°F (149°C) to 400°F (204°C).

Refer to COOKING GUIDELINES in this manual for suggested temperatures and times for various

products.

7. Prepare product and place in suitable pans. When the white Heat light goes off, the oven has

reached the desired preheat temperature.

Cooking

1. Open doors and load the product into the oven. Place pans in the center of the racks. Close doors.

2. Set power level to desired baking setting.

3. Set the Timer. After the preset time lapses, turn timer to OFF position to stop alarm.

4. When product is done, open doors and carefully remove cooked product from the oven. Wipe up

any spills.

— 15 —

End of Day

1. Push Master Switch to OVEN COOL. Leave door ajar while the fan is on to cool the oven.

2. When oven has cooled sufficiently, push Master Switch to OFF.

3. Turn gas valve (located behind panel) OFF and clean oven.

4. Leave door open overnight or when oven is not in use for an extended period of time.

Extended Shutdown

Repeat Steps 1 through 3 above. Unplug oven and shut off manual gas valve.

Fig. 5

— 16 —

CONTROLS — Models SG4C and SG6C Built after October 1999

Always displays [HR:Min] when setting the Time.

Displays [HR:Min] if the countdown time is more than 1 Hour.

Displays [Min:Sec] if the countdown time is less than 1 Hour.

Displays Temperature in °F.

R & H

MODE

Indicates the oven is in the Roast and Hold Mode.

OVEN

READ

Indicates the oven is preheated and ready for cooking.

OVEN

HEATING

Indicates the oven is preheating.

PRIMARY

Primary indicates Menu Items 1, 3, or 5.

SECONDAR

Secondary indicates Menu Items 2, 4, or 6.

Up arrow increases; Down arrow decreases — a displayed Time or

Temperature value if arrow keys are lit.

Adjusts the oven heating rate or Power Level from 20 to 100 %.

TEMPERATURE: Use with SET to set the oven Temperature.

SET

SET: Use with Time or Temperature.

TIME: Use with SET to manually set the cooking Time.

ROAST

HOLD

Selects Roast and Hold mode; also selects Low Fan Speed.

START

STOP

Press once to start; press a second time to stop.

1/2

3/4

5/6

Select Menu Cook Times. Press once for Primary (1, 3, or 5).

Press a second time for Secondary (2, 4, or 6). See next page.

Rack Buttons select individual Menu / Rack # Cook Times — once

programmed.

SET

PRIMARY

SECONDARY

MENU SELECT

1/2

3/4

5/6

POWER LIGHTS

START

ROAST

HOLD

STOP

OFF

COOL

OVEN

OFF

MENU RACK

PL-53504

MODE

R & H

READY

OVEN

HEATING

OVEN

— 17 —

MANUALLY SETTING THE COOK TIME, TEMPERATURE, AND POWER LEVEL

To Set the Cook Time

• Press the SET button. Press the TIME button.

Tine

displays to indicate TIME.

• Use the Up and Down Arrow keys to increase or decrease the displayed Cook Time (HR:min).

• Press the SET button again to save the Time setting in the computer.

To Set the Temperature

• Press the SET button. Press the TEMPERATURE button;

StPt

displays to indicate Setpoint.

• Use the Up and Down Arrow keys to increase or decrease the displayed Temperature value.

• Press the SET button again to save the Temperature setpoint in the computer.

To Set the Power Level

• Press the SET button. Press the % button.

• Use the Up and Down Arrow keys to increase or decrease the displayed Power Level value.

• Press the SET button again to save the desired Power Level value in the computer.

To Start Cooking

• Press the START / STOP button.

• The manual Cook Time counts down to 00:00. Displays [HR:Min] above 1 hour; [min: sec] below.

• The buzzer will sound. To silence the buzzer, press the START / STOP button again.

* The control retains the manual settings for Cook Time, Temperature, and Power Level.

TO PROGRAM MENU ITEM and RACK # Cook Times

Factory Preset and Programmable Cook Times are shown in the table, below:

NOITCELESUNEM UNEM

METIMETI METI METIMETI

TESERPYROTCAF

METIUNEMMETIUNEM METIUNEM METIUNEMMETIUNEM