Greenlee CM-1360, CM-1560, CMH-1000 and CMI-1000 Clamp Meter Manual Manuel utilisateur

Read and understand all of the instructions and safety information in this manual

before operating or servicing this tool.

Lea y entienda todas las instrucciones y la información sobre seguridad que aparecen

en este manual, antes de manejar estas herramientas o darles mantenimiento.

Lire attentivement et bien comprendre toutes les instructions et les informations sur

la sécurité de ce manuel avant d’utiliser ou de procéder à l’entretien de cet outil.

Vor Bedienung oder Wartung dieses Messgerätes bitte alle Anweisungen und

Sicherheitsinformationen in diesem Handbuch genau durchlesen und beachten.

Clamp Meters

Medidores con pinza

Contrôleurs à pince

Zangenmessgeräte

INSTRUCTION MANUAL

MANUAL DE INSTRUCCIONES

MANUEL D’INSTRUCTIONS

BEDIENUNGSANLEITUNG

CM-1360 • CM-1560

CMH-1000 • CMI-1000

Español.............19

Français ...........35

Deutsch ............ 51

2

Description

The Greenlee CM-1360, CM-1560, CMH-1000, and CMI-1000 Clamp Meters are hand-held testing devices

with the following measurement capabilities: AC and DC voltage, AC current, AC current AmpTip™,

frequency, non-contact electric ﬁeld (EF) detection, resistance, and capacitance. They also check diodes

and verify continuity. These meters are designed to be placed on or removed from insulated or uninsulated

conductors.

Additional functionality speciﬁc to each model includes:

Function CMI-1000 CM-1560 CMH-1000

AC + DC Voltage • •

DC Current AmpTip™ • •

DC + AC Current AmpTip™ • •

DC Current • •

Flashlight • •

µDC Current • •

Temperature (K-style thermocouple) • •

Motor Rotation • •

Phase Rotation • •

Peak RMS Capture • • •

5 ms Crest • • •

Other capabilities include:

• Hold Mode to capture the present LCD value

• Record Minimum, Maximum, or Average Mode

• Zero Mode

• Intelligent Auto Power Off

• Automatic ranging

• Backlit LCD

Safety

Safety is essential in the use and maintenance of Greenlee tools and equipment. This instruction manual

and any markings on the tool provide information for avoiding hazards and unsafe practices related to the

use of this tool. Observe all of the safety information provided.

Purpose of This Manual

This instruction manual is intended to familiarize all personnel with the safe operation and maintenance

procedures for the Greenlee CM-1360, CM-1560, CMH-1000, and CMI-1000 Clamp Meters.

Keep this manual available to all personnel. Replacement manuals are available upon request at no charge

at www.greenlee.com.

Do not discard this product or throw away!

For recycling information, go to www.greenlee.com.

All speciﬁcations are nominal and may change as design improvements occur. Greenlee Tools, Inc. shall not be liable for

damages resulting from misapplication or misuse of its products.

® Registered: The color green for electrical test instruments is a registered trademark of Greenlee Tools, Inc.

AmpTip is a trademark of BTC.

KEEP THIS MANUAL

CM-1360 • CM-1560 • CMH-1000 • CMI-1000

3

SAFETY ALERT SYMBOL

This symbol is used to call your attention to hazards or unsafe practices which could result in an

injury or property damage. The signal word, deﬁned below, indicates the severity of the hazard. The

message after the signal word provides information for preventing or avoiding the hazard.

Immediate hazards which, if not avoided, WILL result in severe injury or death.

Hazards which, if not avoided, COULD result in severe injury or death.

Hazards or unsafe practices which, if not avoided, MAY result in injury or property damage.

Read and understand this material before operating or servicing this equipment.

Failure to understand how to safely operate this tool could result in an accident

causing serious injury or death.

Electric shock hazard:

Contact with live circuits could result in severe injury or death.

Electric shock and ﬁre hazard:

• Do not expose this unit to rain or moisture.

• Do not use the unit if it is wet or damaged.

• Clamp meter, test leads or any other clamp accessory, when used to make a measurement, create

a System. The System is rated for CAT III 1000 V or CAT IV 600V when using the test leads or

accessories provided with the meter. The System CAT and voltage rating is limited by the lowest rated

component in the System when using test leads or accessories not provided with the meter.

• Inspect the test leads or accessory before use. They must be clean and dry, and the insulation must be

in good condition. Do not use the test lead if the contrasting inner layer of insulation is visible.

• Use this unit for the manufacturer’s intended purpose only, as described in this manual. Anyotheruse

can impair the protection provided by the unit.

Failure to observe these warnings could result in severe injury or death.

Electric shock hazard:

• Do not apply more than the rated voltage between any two input terminals, or between any input

terminal and earth ground.

• Keep hands and ﬁngers below the barriers on the test leads and the clamp meter body.

Failure to observe these warnings could result in severe injury or death.

Important Safety Information

4

Important Safety Information

Electric shock hazard:

• Do not operate with the case open.

• Before opening the case, remove the test leads from the circuit and shut off the unit.

Failure to observe these warnings could result in severe injury or death.

Electric shock hazard:

• Unless measuring voltage, current, or frequency, shut off and lock out power. Make sure that all

capacitors are discharged. Voltage must not be present.

• Set the selector and connect the test leads so that they correspond to the intended measurement.

Incorrect settings or connections can result in incorrect measurements or damage to the unit.

• Using this unit near equipment that generates electromagnetic interference can result in unstable or

inaccurate readings.

Failure to observe these warnings could result in severe injury or death.

Electric shock hazard:

• Do not change the measurement function while the test leads are connected to a component or

circuit.

• Do not clamp the jaw around a conductor carrying a frequency greater than 400Hz. The magnetic

circuitry may reach a hazardous temperature if this frequency is exceeded.

Failure to observe these precautions may result in injury and can damage the unit.

Electric shock hazard:

• Do not attempt to repair this unit. It contains no user-serviceable parts.

• Do not expose the unit to extremes in temperature or high humidity. Refer to “Speciﬁcations.”

Failure to observe these precautions may result in injury and can damage the unit.

CM-1360 • CM-1560 • CMH-1000 • CMI-1000

5

Identiﬁcation

1. Antenna for non-contact EF detection

2. Jaw center indicator for best current accuracy; polarity indicator for DC amps

3. Selects a function or turns power off

4. LCD

5. Input jack for phase and motor rotation functions only

6. Positive input terminal; L2 input for motor and phase rotation

7. Negative, common, or ground input terminal; L1 input for motor and phase rotation

8. Refer to explanation under “Using the Features.”

9. Jaw lever

10. Keep hand or ﬁngers below the dashed line during operation.

11. Jaw

12. Center indicator for AmpTip™ function

Symbols on the Unit

Warning—Read the instruction manual

Warning—Risk of electric shock

Earth ground

Double insulation

AC (alternating current)

DC (direct current)

Application around or removal from hazardous live conductors is permitted.

12

11

1

2

3

4

6

5

9

10

8

7

6

Display Icons

1. Crest

2. Record function is enabled.

3. Diode

4. Continuity

5. PEAK-RMS mode is enabled.

6. Phase rotation main supply

7. Motor rotation

8. 8.8.8.8 Numeric display

9. µ Micro (10

-6

)

10. F Farad

11. A Ampere

12. V Volt

13. Hz Hertz (frequency in cycles per second)

14. Ω Ohm

15. k Kilo (10

3

)

16. AmpTip™ function is enabled.

17. ∆ Relative zero function is enabled.

18. – Polarity indicator

19. VFD AC measurement with ﬁlter for accuracy on variable frequency drives

20. AC measurement is selected.

21. + AC + DC measurement is selected.

22. DC measurement is selected.

23. Low battery

24. Hold function is selected.

25. MAX Maximum value being displayed

26. MIN Minimum value being displayed

27. AVG Average value being displayed

28. Automatic ranging is enabled.

6-7

23-27

18

17

22

28

20

19

21

8

9-12

1

16 15 14 13

2 3 4 5

CM-1360 • CM-1560 • CMH-1000 • CMI-1000

7

Using the Features

All Models

• Intelligent Auto Power Off (APO): The meter automatically turns off after approximately 32 minutes

of inactivity to extend battery life. Active meter function is speciﬁed as: selector switch is rotated or

pushbuttons are pressed; readings above 8.5% of the range; non-OL readings for resistance, continuity,

or diode function; non-zero readings for Hz function; phase rotation segment moving. To wake up the

meter from APO, press the SELECT button momentarily and release or turn the rotary switch OFF and

then back on. Always turn the rotary switch to the OFF position when the meter is not in use.

• : Press the

button momentarily to toggle the LCD backlight. The backlight automatically

turns off after 32 seconds to extend battery life.

• : Press the

button momentarily to toggle the ﬂashlight. The ﬂashlight automatically turns off

after 32 seconds to extend battery life.

• CREST: Press for 1 second to activate. LCD will indicate when mode is active. This mode will

capture current or voltage peaks in duration of as small as 5 ms. Press CREST to toggle between MIN

and MAX. Add 250 digits to accuracy for changes > 5 ms.

• HOLD: Press momentarily to hold the present value on the display. Press again to exit this mode.

• REC: Press momentarily to activate MAX/MIN/AVG recording mode. and “MAX MIN AVG” appear

on the display. The meter beeps when new maximum or minimum reading is updated. The average

reading is calculated over time. Press the button momentarily to read the MAX, MIN, and AVG readings

in sequence. Press the button for 1 second to exit MAX/MIN/AVG recording mode. APO is disabled

automatically in this mode.

• SELECT: Press momentarily to toggle between functions, measurement modes, or display modes. The

last used setting becomes the default when that function is selected again. To change the default, select

a new setting. The setting will be stored in nonvolatile memory.

• ∆: Press the ∆ button for 1 second to toggle between zero and normal mode. In zero mode the value

on the LCD when the button is pressed becomes the offset. As the input value changes, the offset is

subtracted from the actual value. This modiﬁed value is shown on the LCD.

Note: ∆ operation when DCA or DC + ACA functions are selected offsets any magnetic hysteresis in the

jaw. If DCA or DC + ACA reading before measuring is not zero, press the ∆ button for 1 second. The LCD

will display “dc_0”. When this clears, the meter is ready for operation. When measuring more than 5 A,

this mode is disabled. As an indication, the meter will beep three times.

CM-1560, CMH-1000, and CMI-1000 Only

• PEAK-RMS: Press the PEAK-RMS button for 1 second to activate PEAK-RMS mode to capture inrush

current or voltage in duration as short as 80 ms.

appears on the display. Press the button for

1second to exit PEAK-RMS mode. APO is disabled automatically in this mode.

CMH-1000 and CMI-1000 Only

• and : If desired, press and hold the REC button while turning the meter ON to enable the Beeper

feature. If the segments indicate a clockwise movement, the beeper sounds a single long beep per

segment cycle. If the segments indicate a counterclockwise movement, the beeper sounds three short

beeps per segment cycle.

• : Ensure the motor is electrically isolated from its power source. Press the SELECT button

momentarily to select Motor function. Connect the meter to the motor as described in the “Settings

Table” section of this manual. From the perspective of looking down the shaft of the motor, spin it

clockwise. If the meter indicates a clockwise movement, the motor leads connected to L1, L2, and

L3 of the meter are T1, T2, and T3, respectively. If the meter indicates a counterclockwise move-

ment, swap any two connects between the meter and motor. Then retest.

• : Press the SELECT button momentarily to select Phase function. Connect the meter to the

phases as described in the “Settings Table” section of this manual. If the meter indicates a

clockwise movement, the phases connected to L1, L2, and L3 of the meter are L1, L2, and L3,

respectively. If the meter indicates a counterclockwise movement, swap any two connects between

the meter and phases. Then retest.

8

Using the Test Leads

Electric shock hazard:

The test leads supplied with this product comply with safety standards that limit the exposed length of

the probe tip to 4 mm for measurement categories III and IV. These test leads include a cap that must be

in place when used in measurement category III or IV applications.

Failure to observe this warning could result in severe injury or death.

Cap must be in place for measurement category III or IV applications.

Cap can be removed for measurement category I or II applications.

CM-1360 • CM-1560 • CMH-1000 • CMI-1000

9

AC Measurement

AC measurements are usually displayed as RMS (root mean square) values. The RMS value is equal to the

value of a DC waveform, which would deliver the same power if it replaced the time-varying waveform.

Two AC measurement methods are average-responding RMS calibrated and true RMS-reading.

The average-responding RMS calibrated method takes the average value of the input signal after full wave

rectiﬁcation, multiplies it by 1.11, and displays the result. This method is accurate if the input signal is a

pure sine wave.

The true RMS-reading method uses internal circuitry to read the true RMS value. This method is accurate,

within the speciﬁed crest factor limitations, whether the input signal is a pure sine wave, square wave,

triangle wave, half wave, or signal with harmonics. The ability to read true RMS provides much more mea-

surement versatility. The Greenlee CM-1360, CM-1560, CMH-1000, and CMI-1000 are true RMS meters.

The Waveforms and Crest Factors table shows some typical AC signals and their RMS values.

Waveforms and Crest Factors

Waveform

RMS Value 100 100 100 100

Average Value 90 100 87 64

Crest Factor*

(x)

1.414 1 1.73 2

* The crest factor is the ratio of the peak value to the RMS value;

it is represented by the Greek letter x.

AC + DC True RMS

AC + DC true RMS calculates both of the AC and DC components given by the expression

when making measurements and responds accurately to the total effective RMS value regardless of the

waveform. Distorted waveforms with the presence of DC components and harmonics may cause:

• Transformers, generators, and motors to overheat

• Circuit breakers to trip prematurely

• Fuses to blow

• Neutrals to overheat due to the triplen harmonics present on the neutral

• Bus bars and electrical panels to vibrate

CM-1560 and CMI-1000 can be set to display AC true RMS or AC + DC true RMS.

AC Bandwidth

AC bandwidth is the range of frequencies over which AC measurements can be made within the speciﬁed

accuracy. It is the frequency response of the AC functions—not of the frequency measurement functions. A

meter cannot accurately measure the AC value with frequency spectrums outside its bandwidth. Complex

waveforms, noise, and distorted waveforms contain frequency components that are much higher than the

fundamental; for example, high frequency noise on a 50/60 Hz power line.

10

Operation

Electric shock hazard:

Contact with live circuits could result in severe injury or death.

Operating Procedure

1. Refer to the “Settings Table.” Set the selector to the proper setting, press SELECT (when instructed to

do so), and connect the test leads to the meter.

2. Refer to “Typical Measurements” for speciﬁc measurement instructions.

3. Test the unit on a known functioning circuit or component.

• If the unit does not function as expected on a known functioning circuit, replace the batteries.

• If the unit still does not function as expected, call Greenlee for technical assistance at

800-435-0786.

4. Take the reading from the circuit or component to be tested.

Settings Table

To measure

this value …

Set the

selector to this

symbol…

These icons

appear on the

display …

Connect

the red lead

to…

Connect the

black lead

to …

ALL MODELS

Voltage (AC)

V

+ COM

Voltage (DC)

V

+ COM

Current, AmpTip™ (AC)

A

N/A N/A

Current (AC)

A

N/A N/A

Continuity

Ω

+ COM

Resistance

Ω kΩ

+ COM

Diode

V

+ COM

Frequency

Hz Hz

+ COM

Electric Field (EF)*

EF EF

N/A COM

Capacitance**

µF

+ COM

CM-1560 and CMI-1000 Only

Voltage (AC + DC) + COM

Current, AmpTip™ (DC)

A

N/A N/A

Current, AmpTip™ (AC + DC)

A

N/A N/A

Current (DC)

A

N/A N/A

Current (AC + DC)

A

N/A N/A

CMH-1000 and CMI-1000 Only

Temperature

Temp C or F

***

Current (µDC)

µA

+ COM

Phase Rotation† + COM

Motor Rotation† + COM

* Use the top side of the stationary jaw, or for more precise measurements use a probe in the COM

terminal.

** Discharge capacitor before measurement. Refer to “Typical Measurements” regarding polarized

capacitors.

*** Thermocouple + connects to +, thermocouple – connects to COM.

† Yellow lead connects to L3.

CM-1360 • CM-1560 • CMH-1000 • CMI-1000

11

Typical Measurements and Accuracy

Refer to the “Speciﬁcations” section for operating conditions and temperature coefﬁcient.

Accuracy is speciﬁed as follows: ± (a percentage of the reading + a ﬁxed amount) at 23 °C ± 5 °C

(73.4°F ± 9 °F).

Frequency must be within the speciﬁed bandwidth for non-sinusoidal waveforms. Crestfactors, unless

otherwise speciﬁed, are as follows:

• Crest factor < 2.5:1 at full scale

• Crest factor < 5.0:1 at half scale

Frequency

Function Sensitivity (Sine RMS)* Range

600 V, 1000 V 50 V 5.00 Hz ~ 999.9 Hz

60.0 A AmpTip™ 40 A 40.00 Hz ~ 400.0 Hz

60.00 A, 600.0 A, 1000 A 40 A 40.00 Hz ~ 400.0 Hz

* DC bias must be less than 50% of the Sine RMS value.

Accuracy of Frequency Range

Display Range Accuracy

xx.xx ± (1.0% + 0.05 Hz)

xxx.x ± (1.0% + 0.5 Hz)

Voltage

Measurement

VHz

EF

VFD

SELECT SELECT

VFD

AC Voltage

Range

Accuracy at

20 Hz to 50 Hz

Accuracy at

50 Hz to 60 Hz

Accuracy at

60 Hz to 200 Hz

Accuracy at

200 Hz to 400 Hz

600.0 V ± (1.5% + 0.5 V) ± (0.8% + 0.5 V) ± (1.5% + 0.5 V) ± (10% + 0.5 V)

1000 V ± (1.5% + 5 V) ± (0.8% + 5 V) ± (1.5% + 5 V) ± (10% + 5 V)

DC Voltage

Range Accuracy Range Accuracy

600.0 V ± (0.8% + 0.5 V 1000 V ± (0.8% + 5 V)

AC + DC Voltage (CM-1560 and CMI-1000 only)

Range

Accuracy at

40 Hz to 50 Hz

Accuracy at DC,

50 Hz to 60 Hz

Accuracy at

60 Hz to 200 Hz

Accuracy at

200 Hz to 400 Hz

600.0 V ± (1.8% + 0.7 V) ± (1.0% + 0.7 V) ± (1.8% + 0.7 V) ± (12% + 0.7 V)

1000 V ± (1.8% + 7 V) ± (1.0% + 7 V) ± (1.8% + 7 V) ± (12% + 7 V)

Input Impedance: 10 MΩ, 100 pF nominal

12

Current Measurement

Typical Measurements and Accuracy (cont’d)

Flame Sensor

Control

Board

Pilot Flame

µA

AmpTip™ Function

µA DC Current

μDC Current

(CMH-1000 and CMI-1000 only)

Range Accuracy Burden Voltage

200.0 μA ± (1.0% + 0.5 μA)

3.5 mV/μA

2000 μA ± (1.0% + 5 μA)

A

Hz

AmpTip™ AC Current

Range Accuracy Range

Accuracy at

40 Hz to 100 Hz†

Accuracy at

100 Hz to 400 Hz†

60.00 A

0.00 A to 3.99 A ± (1.5% + 0.15 A) ± (2.0% + 0.15 A)

4.00 A to 60.00 A ± (1.5% + 0.05 A) ± (2.0% + 0.05 A)

† Induced error for adjacent current carrying conductors is < 0.02 A/A.

AmpTip™ DC Current (CM-1560 and CMI-1000 only)

Range Accuracy Range Accuracy†

60.00 A

0.00 A to 3.99 A ± (1.5% + 0.15 A)

4.00 A to 60.00 A ± (1.5% + 0.05 A)

† Induced error for adjacent current carrying conductors is < 0.02 A/A.

AmpTip™ DC + AC Current (CM-1560 and CMI-1000 only)

Range Accuracy Range

Accuracy at DC,

40 Hz to 100 Hz†

Accuracy at

100 Hz to 400 Hz†

60.00 A

0.00 A to 3.99 A ± (2.0% + 0.17 A) ± (2.2% + 0.17 A)

4.00 A to 60.00 A ± (2.0% + 0.07 A) ± (2.2% + 0.07 A)

† Induced error for adjacent current carrying conductors is < 0.08 A/A.

Note: Use Δ if there is an offset before the measurement is taken.

CM-1360 • CM-1560 • CMH-1000 • CMI-1000

13

Typical Measurements and Accuracy (cont’d)

Current Measurement (cont’d)

AC and DC Clamp

A

Hz

AC Current (CM-1560 and CMI-1000 only)

Range Accuracy Range

Accuracy at

40 Hz to 100 Hz*†

Accuracy at

100 Hz to 400 Hz*†

60.00 A

0.00 A to 8.99 A ± (1.8% + 0.15 A) ± (2.2% + 0.15 A)

9.00 A to 60.00 A ± (1.8% + 0.05 A) ± (2.2% + 0.05 A)

600.0 A 60.0 A to 600.0 A ± (1.8% + 0.5 A) ± (2.2% + 0.5 A)

1000 A 600 A to 1000 A ± (1.8% + 5 A) ± (2.2% + 5 A)

* Maximum crest factor < 1.4:1 at full scale and < 2.8:1 at half scale.

† Induced error for adjacent current carrying conductors is < 0.02 A/A.

AC Current (CM-1360 and CMI-1360 only)

Range Accuracy Range

Accuracy at

40 Hz to 100 Hz*†

Accuracy at

100 Hz to 400 Hz*†^

60.00 A

0.00 A to 5.99 A ± (1.8% + 0.15 A) ± (2.2% + 0.15 A)

6.00 A to 60.00 A ± (1.8% + 0.05 A) ± (2.2% + 0.05 A)

600.0 A 60.0 A to 600.0 A ± (1.8% + 0.5 A) ± (2.2% + 0.5 A)

1000 A 600 A to 1000 A ± (1.8% + 5 A) ± (2.2% + 5 A)

* Maximum crest factor < 1.4:1 at full scale and < 2.8:1 at half scale.

† Induced error for adjacent current carrying conductors is < 0.05 A/A.

^ For any measurement, when the conductor is not positioned on the center of the jaws, add 2.0% to the

accuracy for position error.

DC Current (CM-1560 and CMI-1000 only)

Range Accuracy Range Accuracy†

60.00 A

0.00 A to 8.99 A ± (1.8% + 0.15 A)

9.00 A to 60.00 A ± (1.8% + 0.05 A)

600.0 A 60.0 A to 600.0 A ± (1.8% + 0.5 A)

1000 A 600 A to 1000 A ± (1.8% + 5 A)

† Induced error for adjacent current carrying conductors is < 0.02 A/A.

AC + DC Current (CM-1560 and CMI-1000 only)

Range Accuracy Range

Accuracy at DC,

40 Hz to 100 Hz*†

Accuracy at

100 Hz to 400 Hz*†

60.00 A

0.00 A to 8.99 A ± (2.2% + 0.17 A) ± (2.5% + 0.17 A)

4.00 A to 60.00 A ± (2.2% + 0.07 A) ± (2.5% + 0.07 A)

600.0 A 60.0 A to 600.0 A ± (2.2% + 0.7 A) ± (2.5% + 0.7 A)

1000 A 600 A to 1000 A ± (2.2% + 7 A) ± (2.5% + 7 A)

* Maximum crest factor < 1.4:1 at full scale and < 2.8:1 at half scale.

† Induced error for adjacent current carrying conductors is < 0.08 A/A.

Note: Use Δ if there is an offset before the measurement is taken.

14

Typical Measurements and Accuracy (cont’d)

Ω

SELECT

Resistance

Measurement

SELECT

Continuity Check

Resistance

Range Accuracy

600.0 Ω ± (1.0% + 0.5 Ω)

6.000 kΩ ± (1.0% + 0.005 kΩ)

60.00 kΩ ± (1.0% + 0.05 kΩ)

Open Circuit Voltage (typical): 1.7 VDC

Continuity

Tone Threshold: Between 10 Ω and 250 Ω

Response Time: Approximately 32 ms

Capacitance

Measurement

Capacitance

Range Accuracy*

200.0 μF ± (2.0% + 0.4 μF)

2500 μF ± (2.0% + 4 μF)

* For ﬁlm capacitors (capacitors with

negligible dielectric absorption).

Reverse Bias

Forward Bias

SELECT

Diode

Measurement

Diode Test

Measuring Range: 2.000 V

Accuracy: ± (1.5% + 0.005 V)

Test Current (typical): 0.3 mA

Open Circuit Voltage (typical):

< 3.5 VDC

CM-1360 • CM-1560 • CMH-1000 • CMI-1000

15

Typical Measurements and Accuracy (cont’d)

Temperature

SELECT

Temperature (CMH-1000 and CMI-1000 only)

Range Accuracy*

-40.0 °C ~ 99.9 °C ± (1.0% + 0.8 °C)

100 °C ~ 400 °C ± (1.0% + 1 °C)

-40.0 °F ~ 211.8 °F ± (1.0% + 1.5 °F)

212 °F ~ 752 °F ± (1.0% + 2 °F)

* Thermocouples supplied with meter meet

standard JIS C 1602-1981.

Electric Field

A

10 mm

(0.4")

B

SELECT

A–Non-contact OR

B–Contact, precision measurement

Non-contact EF Detection

Typical

Voltage

Range at

50 Hz to 60 Hz

LCD

Indication

20 V 10 V ~ 36 V -

55 V 23 V ~ 83 V - -

110 V 59 V ~ 165 V - - -

220 V 124 V ~ 330 V - - - -

440 V 250 V ~ 1000 V - - - - -

Phase Rotation Motor Rotation

Clockwise Counterclockwise

SELECT

16

Speciﬁcations

Display: LCD, 3-5/6 digits 6000 counts

Polarity: Automatic

Update Rate: 5 per second nominal

Operating Conditions:

-10 °C to 10 °C (14 °F to 50 °F), relative humidity non-condensing

11 °C to 30 °C (51.8 °F to 86 °F), relative humidity ≤ 90%

30 °C to 40 °C (86 °F to 104 °F), relative humidity ≤ 75%

40 °C to 50 °C (104 °F to 122 °F), relative humidity ≤ 45%

Pollution degree: 2

Indoor use only

Altitude:

Operating: Below 2000 m (6500 ft)

Storage: 3000 m (9843 ft)

Storage Temperature: -20 °C to 60 °C, relative humidity < 80%, with batteries removed

Temperature Coefﬁcient: Nominal 0.10 x (Accuracy) per °C below 18 °C from -10 °C to 18 °C

(14 °F to 64.4 °F) and above 28 °C from 28 °C to 50 °C (82.4 °F to 122 °F) or otherwise speciﬁed

Sensing: True RMS

E.M.C.:

Meets EN61326-1:2006 (EN55022, EN61000-3-2, EN61000-3-3, EN61000-4-2, EN61000-4-3,

EN61000-4-4, EN61000-4-5, EN61000-4-6, EN61000-4-8, EN61000-4-11)

In an RF ﬁeld of 1 V/m, resistance modes all models and DC µA (CMH-1000 and CMI-1000):

Total Accuracy = Speciﬁed Accuracy + 80 digits

In an RF ﬁeld of 1 V/m at frequencies 200 MHz ~ 300 MHz, DCA, DC+AC A and ACA mode:

Total Accuracy = Speciﬁed Accuracy + 60 digits

In an RF ﬁeld of 3V/m, all other modes and models not speciﬁed above:

Total Accuracy = Speciﬁed Accuracy + 20 digits

Safety: Double insulation per UL/IEC/EN61010-1 Ed. 3, IEC/EN61010-2-033 Ed. 1, CAN/CSA C22.2 No.

61010-1 Ed. 3, IEC/EN61010-2-032 Ed. 2 & IEC/EN61010-031 Ed. 1.1 to CAT III 600V and CAT IV 300V

AC and DC

Overload Protections:

Jaws:

Current and Frequency Function: 1000 A DC/AC RMS at ≤ 400 Hz

Terminals:

Voltage and Phase Rotation Function: 1100 V DC/AC RMS

All Other Modes and Functions: 1000 V DC/AC RMS

Transient Protection: 8.0 kV (1.2/50 μs surge)

Power Supply: Two 1.5 V AA batteries (IEC LR06)

Low Battery:

Capacitance and Frequency Functions: Approximately 2.85 V

All other Functions: Approximately 2.5 V

Current Consumption:

CM-1560 and CMI-1000: Typically 13 mA

CM-1360 and CMH-1000: Typically 4.3 mA

APO Timing: Idle for 32 minutes

APO Consumption: 5 μA typical

Dimensions: 258 mm x 94 mm x 44 mm (10.1" x 3.7" x 1.7")

Jaw Opening and Conductor Diameter: 51 mm max (2.0")

Statement of Conformity

Greenlee Tools, Inc. is certiﬁed in accordance with ISO 9001 (2000) for our Quality Management Systems.

The instrument enclosed has been checked and/or calibrated using equipment that is traceable to the

National Institute for Standards and Technology (NIST).

CM-1360 • CM-1560 • CMH-1000 • CMI-1000

17

Measurement Categories

These deﬁnitions were derived from the international safety standard for insulation coordination as it

applies to measurement, control, and laboratory equipment. These measurement categories are explained

in more detail by the International Electrotechnical Commission; refer to either of their publications: IEC

61010-1 or IEC 60664.

Measurement Category II

Local level. Appliances, portable equipment, and the circuits they are plugged into. Some examples

include light ﬁxtures, televisions, and long branch circuits.

Measurement Category III

Distribution level. Permanently installed machines and the circuits they are hard-wired to. Some examples

include conveyor systems and the main circuit breaker panels of a building’s electrical system.

Measurement Category IV

Primary supply level. Overhead lines and other cable systems. Some examples include cables, meters,

transformers, and other exterior equipment owned by the power utility.

Maintenance

Electric shock hazard:

Before opening the case, remove the test leads from the circuit and shut off the unit.

Failure to observe this warning could result in severe injury or death.

Replacing the Batteries

1. Disconnect the unit from the circuit.

Turn the unit OFF.

2. Remove the two screws from the

battery access door and remove it.

3. Replace the batteries, making sure to

observe the polarity.

Cleaning and Storage

Periodically wipe the case with a damp

cloth and mild detergent; do not use

abrasives or solvents.

If the meter will not be used for periods

longer than 60 days, remove the batteries

and store them separately.

18

CM-1360 • CM-1560 • CMH-1000 • CMI-1000

19

Descripción

Los medidores con pinza CM-1360, CM-1560, CMH-1000, y CMI-1000 de Greenlee son unidades de

prueba que caben perfectamente en la palma de la mano, capaces de efectuar los siguientes tipos de

mediciones: Voltaje de CA y CC, corriente de CA, AmpTip™ para corriente de CA, frecuencia, detección

de campos eléctricos (EF) sin contacto, resistencia y capacitancia. También sirven para veriﬁcar diodos

y continuidad. Estos medidores están diseñados para ser colocados en o retirados de conductores con

aislamiento o sin aislamiento.

Entre las funciones adicionales especíﬁcas para cada modelo se incluyen:

Función CMI-1000 CM-1560 CMH-1000

Voltaje de CA + CC • •

AmpTip™ para corriente de CC • •

AmpTip™ para corriente de CC + CA • •

Corriente de CC • •

Linterna • •

Corriente de µCC • •

Temperatura (termopar estilo K) • •

Rotación del motor • •

Rotación de fase • •

Captura de RMS máximo • • •

Cresta de 5 ms • • •

Entre otras funciones se incluyen:

• Modo de Retención para capturar el valor de LCD presente

• Modo de Registro mínimo, máximo o promedio

• Modo Cero

• Apagado automático inteligente

• Escala automática

• Pantalla LCD con iluminación de fondo

Acerca de la seguridad

Es fundamental observar métodos seguros al utilizar y dar mantenimiento a las herramientas y equipo

Greenlee. Este manual de instrucciones y todas las marcas que ostenta la herramienta le ofrecen la

información necesaria para evitar riesgos y hábitos poco seguros relacionados con su uso. Siga toda la

información sobre seguridad que se proporciona.

Propósito de este manual

Este manual de instrucciones tiene como propósito familiarizar a todo el personal con los procedimientos

de operación y mantenimiento seguros para los medidores con pinzas CM-1360, CM-1560, CMH-1000, y

CMI-1000 de Greenlee.

Manténgalo siempre al alcance de todo el personal. Puede obtener copias adicionales de manera gratuita,

previa solicitud en www.greenlee.com.

¡No deseche ni descarte este producto!

Para información sobre reciclaje, visite www.greenlee.com.

Todas las especiﬁcaciones son nominales y pueden cambiar conforme tengan lugar mejoras de diseño. Greenlee Tools,

Inc. no se hace responsable de los daños que puedan surgir de la mala aplicación o mal uso de sus productos.

® Registrado: El color verde para instrumentos de veriﬁcación eléctricos es una marca registrada

de Greenlee Tools, Inc.

Amp-Tip es una marca comercial de BTC.

CONSERVE ESTE MANUAL

20

SÍMBOLO DE ALERTA

SOBRE SEGURIDAD

Este símbolo se utiliza para indicar un riesgo o práctica poco segura que podría ocasionar lesiones

o daños materiales. Cada uno de los siguientes términos denota la gravedad del riesgo. El mensaje

que sigue a dichos términos le indica cómo puede evitar o prevenir ese riesgo.

Peligros inmediatos que, de no evitarse, OCASIONARÁN graves lesiones o incluso la muerte.

Peligros que, de no evitarse, PODRÍAN OCASIONAR graves lesiones o incluso la muerte.

Peligro o prácticas peligrosas que, de no evitarse, PUEDEN OCASIONAR lesiones o daños materiales.

Lea y entienda este documento antes de manejar esta herramienta o darle

mantenimiento. Utilizarla sin comprender cómo manejarla de manera segura podría

ocasionar un accidente, y como resultado de éste, graves lesiones o incluso la

muerte.

Peligro de electrocución:

El contacto con circuitos activados podría ocasionar graves lesiones o incluso la

muerte.

Peligro de electrocución e incendio:

• No exponga esta unidad ni a la lluvia ni a la humedad.

• No utilice esta unidad si se encuentra mojada o dañada.

• Los medidores con pinza, las puntas de prueba o cualquier otro accesorio de cierre, cuando se utilizan

para tomar una medición, crean un sistema. El sistema tiene capacidad nominal CAT III 1000 V o

CAT IV 600 V cuando se utilizan los cables de prueba o los accesorios suministrados con el medidor.

El sistema CAT y la capacidad nominal de voltaje están limitados por el componente con capacidad

mínima en el sistema cuando se utilizan cables de prueba o accesorios no suministrados con el

medidor.

• Revise minuciosamente los cables de prueba o el accesorio, antes de utilizarlos. Deberán estar limpios

y secos, y su forro aislante deberá estar en buenas condiciones. No use el cable de prueba si está

visible la capa de aislamiento interior de contraste.

• Utilícela únicamente para el propósito para el que ha sido diseñada por el fabricante,

tal como se describe en este manual. Cualquier otro uso puede menoscabar la protección

proporcionada por la unidad.

De no observarse estas advertencias podrían sufrirse graves lesiones o incluso la muerte.

Importante Información sobre Seguridad

La page charge ...

Greenlee CM-1360, CM-1560, CMH-1000 and CMI-1000 Clamp Meter Manual Manuel utilisateur

Ce manuel convient également à

Greenlee CM-1360, CM-1560, CMH-1000 and CMI-1000 Clamp Meter Manual Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents