Chamberlain RJO70 Manuel utilisateur

• Please read this manual and the enclosed safety materials carefully!

• Fasten the manual near the garage door after installation.

• The door WILL NOT CLOSE unless the Protector System

®

and cable tension

monitor are connected and properly aligned.

• Periodic checks of the garage door opener are required to ensure safe operation.

• This garage door opener is ONLY compatible with myQ

®

accessories.

• The model number label is located behind the hinged door of your opener.

This product is not intended for use on low headroom tracks with outside pickup

drum or garage doors utilizing extension springs. For advanced or customized

adjustments, door springs, and/ or track conﬁgurations, contact a trained door

systems technician.

For Residential Use

Install On Sectional Doors With Torsion Assemblies Only

Wall Mount Garage Door Opener

Model RJO70

The Chamberlain Group, Inc.

300 Windsor Drive

Oak Brook, IL 60523

2

Preparation

When you see these Safety Symbols and Signal Words on the following pages,

they will alert you to the possibility of serious injury or death if you do not

comply with the warnings that accompany them. The hazard may come from

something mechanical or from electric shock. Read the warnings carefully.

When you see this Signal Word on the following pages, it will alert you to the

possibility of damage to your garage door and/or the garage door opener if

you do not comply with the cautionary statements that accompany it. Read

them carefully.

Mechanical

Electrical

Safety Symbol and Signal Word Review

This garage door opener has been designed and tested to offer safe service provided it is installed, operated,

maintained, and tested in strict accordance with the instructions and warnings contained in this manual.

Table of Contents

PREPARATION 2

Safety Symbol and Signal

Word Review

........................................2

Unattended Operation

.......................... 2

Glossary

...............................................3

Is Your Garage Ready?

........................4

Before You Connect with Your

Smartphone

.........................................5

Preparing Your Garage Door

............... 6

Carton Inventory

..................................7

Overview of Installation

........................8

Tools Needed

.......................................9

Attach the Collar to the

Garage Door Opener

..........................10

INSTALLATION 11

Position and Mount the

Garage Door Opener

..........................11

Attach the Emergency Release

Rope and Handle

................................13

Install Power Door Lock

....................14

Position the Cable Tension Monitor

..14

Attach the Cable Tension

Monitor (Required)

............................15

Install the Door Control

(Motion Detecting Control Panel)

...... 16

Install the Smart LED Light

................17

Install the Protector System

®

...........18

Connect Power

...................................21

Align the Safety Reversing Sensors

..22

Install the Battery Backup

..................23

ADJUSTMENT 24

Program the Travel ............................24

Test the Safety Reversal System

.......25

Test the Protector System

................25

Test Power Door Lock

.......................26

Test the Emergency Release

..............26

Test the Cable Tension Monitor

.........26

OPERATION 27

Using Your Garage Door Opener .......28

Using the Door Control

...................... 29

Using the Remote Control

.................30

Connect with Your Smartphone

........31

PROGRAMMING 31

950ESTD Remote Control..................31

Reprogramming the Smart

LED Light............................................33

To Erase the Memory

.........................33

HomeLink

®

......................................... 34

MAINTENANCE 35

Care of Your Garage Door Opener .....35

TROUBLESHOOTING 36

Diagnostic Chart .................................36

Additional Troubleshooting

................37

Automatic Garage Door Opener

Safety & Maintenance Guide 39

ACCESSORIES 41

WARRANTY 42

REPAIR PARTS 43

Installation Parts ................................43

Garage Door Opener

Assembly Parts

.................................. 43

CONTACT INFORMATION 44

UNATTENDED OPERATION

The Timer-to-Close (TTC) feature, the myQ

®

App, and myQ

®

Garage Door are examples of unattended close and are to

be used ONLY with sectional doors. Any device or feature that allows the door to close without being in the line of sight

of the door is considered unattended close.

The Smart LED light must be installed to enable use of Timer-To-Close or myQ

®

App control of the door.

WARNING: This product can expose you to chemicals including lead, which are known to the State

of California to cause cancer or birth defects or other reproductive harm. For more information go to

www.P65Warnings.ca.gov.

3

Glossary

Here are some basic terms you may encounter as you prepare and install your garage door opener.

Preparation (continued)

Track

Roller

Drum

Hinge

Torsion

springs

Torsion bar

Bearing

plate

Center bearing

plate

Electrical

outlet

Sectional door

Floor

Door seal

Term Deﬁnition

Bearing Plate Acts as a support for the torsion bar. The bearing and mounting plate are typically located

above the garage door.

Cable Tension

Monitor

The cable tension monitor detects any slack in the garage door cables. Failure to properly

install the cable tension monitor may cause the cables to be thrown and may result in a

hazardous situation. (Not shown below)

Door Seal The door seal is located at the bottom of the door and helps to keep outdoor elements from

entering the garage.

Drum Drums are round, grooved spools on the torsion bar that keep door cables orderly.

Extension Springs Extension springs are NOT compatible with this opener. Extension springs are typically

mounted along the horizontal section of the track and extend from the front of the door

opening to the back hang. The springs are intended to make a door lighter so you can easily

open and close the door by hand.

High Lift

Sectional Door

A type of garage door constructed with multiple panels that slide along a track inside the

garage. The track runs vertically up the wall beyond the top of the door opening several

inches before encountering the curve in the track. The extended distance above the top of the

garage door determines the amount of a high lift.

Roller Small wheels which allow the door to move up and down the track.

Safety Reversing

Sensor

The safety reversing sensors are a set of sensor eyes that detect obstructions in the path of

the garage door. If an obstruction is found, the sensors tell the door to reverse direction.

(Not shown below)

Torsion Springs A torsion spring is a type of spring that counter balances the garage door. The torsion spring is

located above the door on the torsion bar. The springs are intended to make a door lighter so

you can easily open and close the door by hand. Consult a trained door systems technician if

you need the springs adjusted or replaced.

Torsion Bar A torsion bar is a horizontal metal bar mounted above the garage door. The torsion springs

are located on the torsion bar. Most torsion bars are hollow, while some are solid. Some

solid torsion bars may have a groove called a keyway that runs the length of the bar.

4

Is Your Garage Ready?

Use this check list to see if your garage is compatible with the garage door opener requirements. Note that you can

install the garage door opener on either the left or the right side of the garage door.

IMPORTANT: Your garage MUST meet the following requirements to install this opener to ensure safe and proper

operation. If your door does not meet these criteria, you must choose a different model of operator. If your torsion

bar, power source and/or drums do not meet the requirements, contact a trained door systems technician.

REQUIREMENTS CHECK LIST

Sectional garage door:

• Standard sectional door up to 14 feet (4.3 m) high, but only up to 180 sq. ft. (16.7 sq. m).

• Standard sectional doors up to 18 feet (5.5 m) wide, but only up to 180 sq. ft. (16.7 sq. m)

• Standard sectional high lift door (up to 54 inches (137.2 cm) of high lift)

• Any gap between the ﬂoor and the bottom of the door must not exceed 1/4 inch (6 mm). Otherwise, the safety

reversal system may not work properly. .

Torsion bar and torsion springs:

• Torsion bar is 1 inch (2.5 cm) diameter.

• Torsion bar must extend at least 1-1/2 inches (3.81 cm) past the bearing plate and be free of damage.

• Distance between ceiling and center of torsion bar is 3 inches (7.6 cm) or more.

• Distance between garage wall the torsion bar is mounted on and center of torsion bar is 2-1/2 inches (6.4 cm)

or more.

• A minimum of 8.5 inches (21.6 cm) between the side garage wall (or obstruction) and the end of the torsion

bar.

D rums:

• NOT compatible with reverse wound drums.

• Must be 4-6 inches (10-15 cm) diameter.

• 3-3.9 inch (7.6-9.9 cm) diameter drums may be used on doors up to 430 lbs (194kgs).

Power:

• An electric outlet must be accessible within a 6 foot (1.83 m) diameter of the installation area for the opener.

The outlet must be 120 VAC - 60 Hz ONLY. Contact a qualiﬁed electrician if you need an outlet installed.

Previously installed garage door opener has been removed completely.

Preparation (continued)

Wall

Side view of torsion bar

Torsion bar must extend

at least 1-1/2 inches (3.81

cm) past the bearing plate

Electric outlet

within 6 ft

(1.83 cm) of

opener

2-1/2"

(6.4 cm)

3"

(7.6 cm)

Ceiling

Distance between ceiling

and torsion bar is 3"

(7.6 cm) or more

Ceiling

Torsion bar

Drum

Wall

with

door

Gap between floor and

bottom of door must

not exceed 1/4" (6 mm)

Wall or

obstruction

Torsion bar

8.5 inches

(21.6 cm)

5

Before You Connect with Your Smartphone

Preparation

Monitor and control your garage door from anywhere using the myQ

®

App.

BEFORE YOU BEGIN:

You will need:

• Wi-Fi

®

enabled smartphone, tablet or laptop

• Broadband Internet Connection

• Wi-Fi

®

signal in the garage (2.4 Ghz, 802.11b/g/n required)

• Password for your home network (router's main account, not guest

network)

TEST THE WI-FI

®

SIGNAL STRENGTH

Make sure your mobile device is connected to your Wi-Fi

®

network. Hold your

mobile device in the place where your garage door opener will be installed and

check the Wi-Fi

®

signal strength.

For compatible router speciﬁcations and help, visit www.chamberlain.com/Customer-Support

See page 31 to connect the garage door opener to a mobile device.

Check Signal Strength. If you see:

Wi-Fi

®

signal is strong.

The garage door opener

will connect to your

Wi-Fi

®

network.

Wi-Fi

®

signal is weak.

The garage door opener may connect

to your Wi-Fi

®

network. If not, try one

of the options below to improve the

Wi-Fi

®

signal:

No Wi-Fi

®

signal.

The garage door opener will not be

able to connect to your Wi-Fi

®

network. Try one of the options below

to improve the Wi-Fi

®

signal:

• Move your router closer to the garage door opener to

minimize interference from walls and other objects

• Buy a Wi-Fi

®

range extender

6

Prepare your Garage Door

To prevent damage to garage door and opener:

• ALWAYS disable locks BEFORE installing and operating the opener.

• ONLY operate garage door opener at 120 V, 60Hz to avoid malfunction and damage.

To prevent possible SERIOUS INJURY or DEATH:

• ALWAYS call a trained door systems technician if garage door binds, sticks, or is out of balance. An unbalanced

garage door may NOT reverse when required.

• NEVER try to loosen, move or adjust garage door, door springs, cables, pulleys, brackets or their hardware, ALL

of which are under EXTREME tension.

• Disable ALL locks and remove ALL ropes connected to garage door BEFORE installing and operating garage door

opener to avoid entanglement.

Preparation (continued)

____ 1. Uninstall previous garage door opener.

____ 2. Disable locks.

____ 3. Remove any ropes connected to the garage door.

____ 4. Check the seal on the bottom of the door. Any gap between the ﬂoor and the bottom of the door must not

exceed 1/4 inch (6 mm). Otherwise, the safety reversal system may not work properly.

Complete the test below to make sure the garage door is balanced and is not

sticking or binding.

____

1. Lift the door 3-4 feet off the ground. Release the door. If balanced, it should stay in

place, supported entirely by its springs.

____ 2. Raise and lower the door to check for binding or sticking.

If your door binds, sticks, or is out of balance, contact a trained door systems technician

BEFORE you install this opener.

SPECIFICATIONS

Volts

................................... 120 Vac - 60 Hz, ONLY

Current

.............................................1.5 AMP

LED Light Current (independently powered)

................0.2 AMPS

7

Carton Inventory

Save the carton and packing material until the installation and adjustment is complete. The images throughout this manual

are for reference only and your product may look different.

Preparation (continued)

Remote Control

Visor Clip

1-Button Premium

Remote Control

Model 950ESTD (1)

Smart LED Light myQLED1

(Garage Door Opener Light)

with Hardware Bag

Automatic Garage Door Lock

with Wire and Connector

NOTE: Older model 24V door locks

are incompatible

2 Conductor Wire

White and White/Red

Garage Door Opener

Cable Tension Monitor with

2-Conductor Green/White Wires Mounting Bracket

Collar with

Set Screws

Safety Reversing Sensor Bracket (2)

The Protector System

®

(2) Safety Reversing Sensors

(1 Sending Sensor and

1 Receiving Sensor) with

2-Conductor White and

White/Black Wire attached

Safety Labels

and Literature

Motion-Detecting

Control Panel

Battery

Screw #10-32 (2)

Screw 14-10x2" (4)

Handle

Rope

Screw 1/4"-20x1/2" (2)

Drywall Anchor (Screw-In) (2)

Screw 8-32x1" (2)

Screw 6ABx1-1/4" (2)

Drywall Anchor (2)

Screw 6-32x1" (2)

Carriage Bolt 1/4"-20x1/2" (2)

Wing Nut 1/4"-20 (2)

REMOTE LIGHT HARDWARE:

myQ Remote LED Light Model myQLED1

Drywall Anchor (Screw-In) (2)

Screw #6x1" (2)

ACCESSORIES

Screw

#10-32 (2)

REMOTE LIGHT HARDWARE

INCLUDED HARDWARE

Screw

14-10x2" (4)

Screw

1/4"-20x1/2" (2)

Lag Screw

5/16"-9x2"

Screw 1/4-20 (2) Wall Anchor (2)

Staples

#8 Hex Head Screw (2)

Screw #6 (2) Wall Anchor (2)

Staples

Screw

#8-32x1" (2)

Drywall Anchor (screw-in) (2)

Lag Screw

5/16"-9x2"

Screw 1/4-20 (2) Wall Anchor (2)

Staples

#8 Hex Head Screw (2)

Screw #6 (2) Wall Anchor (2)

Staples

Screw 6ABx1-1/4"

(Standard installation) (2)

Screw 6-32x1"

(pre-wired) (2)

Drywall

Anchors (2)

Rope

Handle

Wing Nut

1/4"-20 (2)

Carriage Bolt

1/4"-20x1/2" (2)

Drywall Anchor (screw-in) (2)

Screw #6x1" (2)

8

Safety reversing

sensor and bracket

Safety reversing

sensor and bracket

Door control wire

Door control

LED remote light

Safety reversing

sensor wire

Safety reversing

sensor wire

Door lock wire

Cable tension

monitor and wire

Overview of Installation

Preparation (continued)

ADDITIONAL ITEMS YOU MAY NEED FOR THE INSTALLATION:

Survey your garage area to see if you will need any of the following items:

• Wood blocks and/or shimming material.

- Used to mount the cable tension monitor.

• Fastening hardware.

- Alternate ﬂoor mounting of the safety reversing sensor will require hardware not provided.

• Extension brackets (Model 041A5281-1) or wood blocks and shimming material.

- Used to position the garage door opener during installation and for testing the safety reversing sensors if installed on

the wall or ﬂoor.

9

Installation

Tools You Will Need

During assembly, installation and adjustment of the garage door opener, you will need these tools.

Pliers

Wire Cutters

Wire Strippers

Claw Hammer

Screwdriver

Level

3/8" Open End Wrench

1/4", 5/16" and 3/8" Sockets

and Wrench with 6" Extension

Drill

Tape Measure

Stepladder

Pencil

Needle Nose Pliers

5/32", 3/16", 5/16"

and 3/4" Drill Bits

IMPORTANT INSTALLATION INSTRUCTIONS

To reduce the risk of SEVERE INJURY

or DEATH:

1. Read and follow all warnings and instructions.

2. Install garage door opener ONLY on properly

balanced and lubricated garage door. An

improperly balanced door may NOT reverse when

required and could result in SEVERE INJURY or

DEATH.

3. ALL repairs to cables, spring assemblies and

other hardware MUST be made by a trained door

systems technician BEFORE installing opener.

4. Disable ALL locks and remove ALL ropes

connected to garage door BEFORE installing

opener to avoid entanglement.

5. Where possible, install the door opener 7 feet

(2.13 m) or more above the ﬂoor.

6. Mount the emergency release within reach, but at

least 6 feet (1.83 m) above the ﬂoor and avoiding

contact with vehicles to avoid accidental release.

7. NEVER connect garage door opener to power

source until instructed to do so.

8. NEVER wear watches, rings or loose clothing

while installing or servicing opener. They could

be caught in garage door or opener mechanisms.

9. Install wall-mounted garage door control:

• within sight of the garage door.

• out of reach of small children at a minimum

height of 5feet (1.53m) above ﬂoors, landings,

steps or any other adjacent walking surface.

• away from ALL moving parts of the door.

10. Install the emergency release marking. Attach

the marking on or next to the emergency release.

Install the entrapment warning placard next to the

door control in a prominent location.

11. Place emergency release/safety reverse test label

in plain view on inside of garage door.

12. Upon completion of installation, test safety

reversal system. Door MUST reverse on contact

with a 1-1/2" (3.8 cm) high object (or a 2x4 laid

ﬂat) on the ﬂoor.

13. To avoid SERIOUS PERSONAL INJURY or DEATH

from electrocution, disconnect ALL electric and

battery power BEFORE performing ANY service or

maintenance.

14. SAVE THESE

INSTRUCTIONS.

10

The garage door opener can be installed on either side of the door; see "Is Your

Garage Ready?" on page 4. The illustrations shown are for installation on

the left side.

1. Loosen the preset collar screws with the 3/8" open end wrench.

2. Slide the collar onto the garage door opener shaft until it stops.

3. Position the collar so the screws are facing out and accessible when

attached to the torsion bar.

4. Tighten the 2 square head set screws by hand until they contact the torsion

bar. Then, use a socket wrench to ﬁnish tightening the set screws by

turning them 1/4 - 1/2 turn.

5. Loosely attach slotted side of mounting bracket to the same side of the

garage door opener as the collar, using screws provided. NOTE: Do not

tighten mounting bracket screws until instructed.

Attach the Collar to the Garage Door Opener

1

To prevent possible SERIOUS

INJURY or DEATH, the collar

MUST be properly tightened. The

door may not reverse correctly or

limits may be lost due to collar

slip.

Collar

Motor Shaft

Set Screws

Socket

Wrench

Bracket

YOU WILL NEED

Screw

#10-32 (2)

Collar

Mounting

bracket

Installation (continued)

11

Bearing

Plate

Collar

Torsion Bar

.25" min. space

between

bearing and

collar

Opener MUST be

parallel to door

Mounting Bracket

YOU WILL NEED

Position and Mount the Garage Door Opener

2

1. Close the garage door completely.

2. Slide the garage door opener onto the end of the torsion bar. Ensure the

collar does NOT touch the bearing plate.

3. Use a level to align the garage door opener parallel to the door. Verify the

mounting bracket installation wall is a solid surface, such as wood, concrete

or a door/ﬂag bracket.

IMPORTANT: If installing on drywall, the mounting bracket MUST be

attached to a stud.

4. When the garage door opener is properly aligned, mark the mounting

bracket holes. If necessary, tighten collar screws on the torsion bar to hold

garage door opener in place while marking holes.

NOTE: The garage door opener does not have to be ﬂush to the wall.

To prevent possible SERIOUS

INJURY or DEATH:

• Concrete anchors MUST be

used if mounting bracket into

masonry.

• NEVER try to loosen, move or

adjust garage door, springs,

cables, pulleys, brackets or

their hardware, ALL of which

are under EXTREME tension.

• ALWAYS call a trained door

systems technician if garage

door binds, sticks or is out of

balance. An unbalanced garage

door might NOT reverse when

required.

• Garage door opener MUST be

mounted at a right angle to the

torsion bar to avoid premature

wear on the collar.

Screw

14-10x2" (2)

Installation (continued)

12

5. Remove the garage door opener from torsion bar.

6. Drill 3/16 inch pilot holes at the marked locations. Drill through metal door rail plates if necessary.

7. Slide the garage door opener back onto the torsion bar until pilot holes align with bracket.

8. Tighten the 2 square head set screws on the torsion bar. For a hollow torsion bar, tighten screws 3/4 - 1 full turn

after making contact with the bar. For a solid shaft torsion bar, tighten screws 1/4 - no more than 1/2 turn after

making contact with the shaft. If installing on a keyed torsion bar, DO NOT tighten the screws into the keyway.

9. Secure the mounting bracket to the wall and to the garage door opener. Use the 14-10x2" screws to secure the

mounting bracket to the wall.

Installation (continued)

Screws 14-10x2"

Set screws

(Torsion bar)

Mounting Bracket

NOTE: Due to torsion bars being out-of-round, the operator may wobble during operation. This is normal.

13

Attach the Emergency Release Rope and Handle

Power Door Lock Location

3

4

1. Thread one end of the rope through the hole in the top of the red handle so

“NOTICE” reads right side up. Secure with an overhand knot at least 1 inch

(2.5 cm) from the end of the rope to prevent slipping.

2. Thread the other end of the rope through the loop in the emergency release

cable. Adjust rope length so the handle is within reach but is no lower than

6 feet (1.83 m) above the ﬂoor, and avoid contact with vehicles to avoid

accidental release. Secure with an overhand knot.

NOTE: If it is necessary to cut the rope, heat seal cut rope end with a match or

lighter to prevent unraveling.

1. Determine where to install the power

door lock.

• Mount the door lock on the same side

as the opener. The third roller from

the ﬂoor is ideal for most installations.

• The power door lock MUST be

mounted within 10 feet (3.05m)

of garage door opener with

approximately a 3 inch (7.6 cm)

distance between the center of a door

roller and the hole for the power door

lock bolt.

Garage Door

Opener

Emergency

Release Cable

Overhand

Knot

Overhand

Knot

Emergency

Release Handle

To prevent possible SERIOUS

INJURY or DEATH from a falling

garage door:

• If possible, use emergency

release handle to disengage

door ONLY when garage

door is CLOSED. Weak or

broken springs or unbalanced

door could result in an open

door falling rapidly and/or

unexpectedly.

• NEVER use emergency release

handle unless garage doorway is

clear of persons and obstructions.

10 feet (3.05 m) max.

3"(7.6 cm)

Garage Door

Track

Rope

Handle

YOU WILL NEED

Installation (continued)

14

Approx. 3"

(7.6 cm)

2

3 4

5

6

Installation (continued)

Install Power Door Lock

5

1. Pull down on the manual release to

disengage the door and open the door

manually.

2. Clean track surface, and attach lock

template to the track.

3. Drill holes as marked on the template.

You may ﬁnd it useful to pre-drill

the holes with a smaller bit before

proceeding to larger sizes.

4. Fasten power door lock to the outside

of the garage door track with

1/4"-20x1/2" screws provided.

5. Run wire up wall to garage door

opener. Use insulated staples to secure

wire in several places.

6. Insert wire through the bottom of

the garage door opener and plug the

connector into the garage door opener.

A secondary door lock can be installed on

the opposite side of the door by following

the instructions above.

Position the Cable Tension Monitor (Required)

6

The cable tension monitor detects any slack in the garage

door cables. When slack is detected, the garage door

opener stops the door from closing, and reverses the

door to stay open. The cable tension monitor MUST be

connected and properly installed BEFORE the garage door

opener will move in the down direction.

The cable tension monitor must be installed on the

same side as the garage door opener. Factory default is

conﬁgured for left-side installation.

1. Determine if the cable tension monitor will be installed

on the left or right side of the door.

2. For left-side installation, skip to Step 3. For right-side

installation ONLY, remove the c-clip from the roller shaft,

move the roller to the other side, and reinstall the c-clip.

3. Make sure the door cable is approximately 3/4" (19 mm)

from the mounting surface.

4. Position the cable tension monitor 2" to 6" (5-15 cm)

from the drum, and over a wood support surface.

- Shim or add wood block if needed. The cable tension

monitor MUST be ﬂush with the mounting surface.

- Cable tension monitor roller must be free from

obstructions.

NOTE: No obstructions should exist that prevent the cable

tension monitor from closing completely when slack is

detected.

YOU WILL NEED

Screw

1/4"-20x1/2" (2)

2" to 6"

(5-15 cm)

Approx. 3/4"

(19 mm)

shim if

needed

Cable tension

monitor

Drum

1

Approx. 3"

(7.6 cm)

15

Attach the Cable Tension Monitor

7

Drum

Header

Cable

Wall

Cable Tension

Monitor

Cable Tension

Monitor Roller

To insert or

release wire,

push in tab with

screwdriver tip

WHT/

GRN

YOU WILL NEED

Lag Screw

5/16"-9x2"

Screw 1/4-20 (2) Wall Anchor (2)

Staples

#8 Hex Head Screw (2)

Screw #6 (2) Wall Anchor (2)

Staples

Lag Screw

5/16"-9x2"

Screw 1/4-20 (2) Wall Anchor (2)

Staples

#8 Hex Head Screw (2)

Screw #6 (2) Wall Anchor (2)

Staples

Screws

#8-32x1" (2)

Drywall Anchor

(screw-in) (2)

Screw

14-10x2" (2)

Installation (continued)

1. Mark and drill 3/16 inch pilot holes for screws. If the cable tension monitor

cannot be mounted into wood, it can be mounted into 1/2 inch (1 cm)

or greater drywall using the drywall anchors (2) and the #8 screws (2)

provided in the hardware bag.

2. Attach the cable tension monitor to the wall using the hardware provided.

Check that the roller is on top of the cable.

3. Run wire to garage door opener. Securely afﬁx wire to wall and ceiling.

Secure any additional wire away from the moving parts of the door.

4. Connect wire to the green quick-connect terminals on the garage door

opener.

NOTE: Cable must have tension through entire door travel. Check there is no

slack in cable on opposite side of garage door during normal operation. If

slack occurs during door travel, contact a trained door systems technician .

A second cable tension monitor may be installed for additional security. When

two cable tension monitors are installed, the door will not close or will reverse

if either one of the monitors detects slack or is disconnected.

Shim or add wood

block if needed.

The cable tension

monitor MUST

be ﬂush with the

mounting surface.

The cable tension

monitor roller

must be free from

obstructions.

Garage door opener

16

Installation (continued)

Install door control within sight of garage door, out of reach of small

children at a minimum height of 5 feet (1.5 m) above ﬂoors, landings,

steps or any other adjacent walking surface, and away from ALL moving

parts of door.

For gang box installations it is not necessary to drill holes or install the

drywall anchors. Use the existing holes in the gang box.

1. Strip 7/16" (11 mm) of insulation from one end of the wire and separate

the wires.

2. Connect wires to the door control. Make sure the polarity is correct.

• Connect the red wire to the RED terminal.

• Connect the white wire to the WHT terminal.

3. Mark the location of the bottom mounting hole and drill a 5/32" (4 mm)

hole.

4. Install the bottom screw, allowing 1/8" (3 mm) to protrude from the wall.

5. Position the bottom hole of the door control over the screw and slide

down into place.

6. Lift the push bar up and mark the top hole.

7. Remove the door control from the wall and drill a 5/32" (4 mm) hole for

the top screw.

8. Position the bottom hole of the door control over the screw and slide

down into place. Attach the top screw.

9. Run the white and red/white wire from the door control to the garage

door opener. Attach the wire to the wall and ceiling with the staples (not

applicable for gang box or pre-wired installations).

10. Strip 7/16" (11 mm) of insulation from the end of the wire near the

garage door opener. Connect wire to the quick-connect terminals on the

garage door opener: white to white and white/red to red.

11. Fasten the warning placard to the wall next to the door control.

NOTE: DO NOT connect the power and operate the garage door opener at

this time. The door will travel to the full open position but will not return

to the close position until the safety reversing sensors are connected and

properly aligned. See page 18.

Install the Door Control

8

To prevent possible SERIOUS

INJURY or DEATH from electrocution:

• Be sure power is NOT connected

BEFORE installing door control.

• Connect ONLY to 7-28 VOLT low

voltage wires.

To prevent possible SERIOUS

INJURY or DEATH from a closing

garage door:

• Install door control within sight of

garage door, out of reach of small

children at a minimum height of 5

feet (1.5 m) above ﬂoors, landings,

steps or any other adjacent walking

surface, and away from ALL

moving parts of door.

• NEVER permit children to

operate or play with door control

push buttons or remote control

transmitters.

• Activate door ONLY when it can be

seen clearly, is properly adjusted,

and there are no obstructions to

door travel.

• ALWAYS keep garage door in sight

until completely closed. NEVER

permit anyone to cross path of

closing garage door.

YOU WILL NEED

Red

Tabs

White

WHT/RED

WHT

To insert or

release

wire, push

in tab with

screwdriver

tip

7/16" (11 mm)

Push bar

Screw 6ABx1-1/4" (Standard installation) (2)

Screw 6-32x1"

(pre-wired) (2)

Drywall

Anchors (2)

(to garage

door opener)

(to door control)

1

2

9

10

3

4 5

67

8

17

Installation (continued)

Screws

Light Lens

Drywall

Anchors

6-1/8" (15.6 cm)

Cord Retainer

Channel

The Smart LED Light is designed to plug

directly into a standard 120V outlet.

Select an appropriate location on the

ceiling or wall to mount the light within

6 feet (1.83 m) of an electrical outlet so

that the cord and light are away from

moving parts.

NOTE: If installing light on drywall and

a ceiling joist cannot be located, use

drywall anchors provided. No pilot hole

is required for drywall anchors.

1. Drill pilot holes 6-1/8" (15.6 cm)

apart if mounting to joist.

OR

Screw in drywall anchors 6-1/8"

(15.6cm) apart if mounting to

drywall.

2. Determine the length of power cord

needed to reach the nearest outlet.

Wind any excess cord around cord

retainer on the top side of the light

base. Route the cord through the

channel so the light mounts ﬂush.

3. Open the light lens.

4. Mount the light with the screws

provided.

5. Close the light lens.

6. Plug in the light to the outlet.

NOTE: The LED light is very bright. DO

NOT stare at the light while on a ladder.

Your remote light has already been

programmed at the factory to operate

with your garage door opener. Any

additional or replacement remote lights

will need to be programmed.

Install the Smart LED

Light

9

IMPORTANT INSTALLATION INSTRUCTIONS

To reduce the risk of SEVERE INJURY or DEATH:

• This portable luminaire has a polarized plug (one

blade is wider than the other) as a feature to reduce

the risk of electric shock.

• This plug will ﬁt in a polarized outlet ONLY one way.

If the plug does not ﬁt fully in the outlet, reverse

the plug. If it still does not ﬁt, contact a qualiﬁed

electrician.

•. DO NOT alter the plug.

•. Light is intended for ceiling or wall mount and

indoor applications ONLY.

Drywall Anchor (screw-in) (2)

HARDWARE

Screw #6x1" (2)

18

Install the Protector System

®

10

Installation (continued)

The safety reversing sensor must be connected and aligned correctly

before the garage door will move in the down direction. This is a required

safety device and cannot be disabled.

IMPORTANT INFORMATION ABOUT THE SAFETY REVERSING SENSOR

When properly connected and aligned, the safety reversing sensor will detect

an obstacle in the path of its electronic beam. The sending sensor (with an

amber indicator light) transmits an invisible light beam to the receiving sensor

(with a green indicator light). If an obstruction breaks the light beam while the

door is closing, the door will stop and reverse to full open position, and the

opener lights will ﬂash 10 times.

The sensors must be installed inside the garage so that the sending and

receiving sensors face each other across the door, no more than 6 inches

(15 cm) above the ﬂoor. Either sensor can be installed on the left or right of

the door as long as the sun never shines directly into the receiving sensor lens.

The mounting brackets are designed to clip onto the track of sectional garage

doors without additional hardware.

If it is necessary to mount the sensors on the wall, the brackets must be

securely fastened to a solid surface such as the wall framing. Extension

brackets (see accessories) are available if needed. If installing in masonry

construction, add a piece of wood at each location to avoid drilling extra holes

in masonry if repositioning is necessary.

The invisible light beam path must be unobstructed. No part of the garage

door (door tracks, springs, hinges, rollers or other hardware) may interrupt the

beam while the door is closing.

Invisible Light Beam

Protection Area

Safety Reversing Sensor

6" (15 cm) max. above ﬂoor

Safety Reversing Sensor

6" (15 cm) max. above ﬂoor

Be sure power is NOT connected

to the garage door opener

BEFORE installing the safety

reversing sensor.

To prevent SERIOUS INJURY or

DEATH from a closing garage

door:

• Correctly connect and align the

safety reversing sensor. This

required safety device MUST

NOT be disabled.

• Install the safety reversing

sensor so beam is NO HIGHER

than 6" (15 cm) above garage

ﬂoor.

Safety Reversing

Sensor

6" (15 cm) max.

above floor

Safety Reversing

Sensor

6" (15 cm) max.

above floor

Invisible Light

Beam Protection

Area

Facing the door from inside the garage.

19

OPTION C: Floor Installation

1. Use wood blocks or extension brackets (see

Accessories) to elevate sensor brackets so the

lenses will be no higher than 6" (15 cm) above

the ﬂoor.

2. Carefully measure and place right and left

assemblies at the same distance out from the

wall. Be sure all door hardware obstructions

are cleared.

3. Fasten to the ﬂoor with concrete anchors as

shown.

Inside

Garage

Wall

Inside

Garage

Wall

Inside

Garage

Wall

Inside

Garage

Wall

Fasten Wood Block to Wall with

Lag Screws (not provided)

Attach with Concrete Anchors

(not provided)

OPTION A: Track Installation (Recommended)

1. Slip the curved arms over the rounded edge of

each door track, with the curved arms facing

the door, and make sure brackets measure no

higher than 6" (15 cm) above the ﬂoor.

2. Snap bracket into place against the side of the

track. It should lie ﬂush, with the lip hugging

the back edge of the track, as shown.

If your door track will not support the bracket

securely, see Option B: Wall Installation.

OPTION B: Wall Installation

1. Place the bracket against the wall with

curved arms facing the door. Be sure there is

enough clearance for the sensor beam to be

unobstructed.

2. If additional depth is needed, an extension

bracket (Model 041A5281-1) or wood blocks

can be used. See Accessories section.

3. Use bracket mounting holes as a template to

locate and drill (2) 3/16" diameter pilot holes on

the wall at each side of the door, no higher than

6" (15 cm) above the ﬂoor.

4. Attach brackets to wall with lagscrews

(notprovided).

If using extension brackets or wood blocks, adjust

right and left assemblies to the same distance out

from the mounting surface. Make sure all door

hardware obstructions are cleared.

If Option B will not work, see Option C: Floor

Installation.

Inside

Garage

Wall

Inside

Garage

Wall

INSTALLING THE BRACKETS

The brackets house the safety reversing sensors in a ﬁxed, secure position so the safety reversing sensors will face

each other across the garage door, with the beam no higher than 6" (15 cm) above the ﬂoor. Be sure power to the

opener is disconnected.

Choose one of the following installations.

Door Track

Safety Reversing Sensor

Bracket

Safety Reversing Sensor Bracket

Lag Screws (not provided)

Safety Reversing Sensor Bracket

Inside

Garage

Wall

Inside

Garage

Wall

(Provided with Extension Bracket)

Extension Bracket (See Accessories)

Safety Reversing Sensor

Bracket

(Provided with

Extension Bracket)

Installation (continued)

Door

20

WIRE THE SAFETY REVERSING SENSORS

1. Run the wire from both sensors to the garage door opener. Securely afﬁx

the wire to the wall and ceiling with staples (not provided).

2. Strip 7/16 inch (11 mm) of insulation from each set of wires. Separate white

from the black the wires. Twist the white wires together. Twist the white/

black wires together.

3. On the garage door opener, push the tab with a screwdriver tip to insert the

white wires into the white terminal and the white/black wires into the grey

terminal.

WHT/

BLK

Tab

Wire

WHT

MOUNTING THE SAFETY REVERSING SENSORS

1. Slide a 1/4"-20x1/2" carriage bolt head into the slot on each sensor.

2. Use wing nuts to fasten safety reversing sensors to brackets, with lenses

pointing toward each other across the door. Be sure the lens is not

obstructed by a bracket extension.

3. Finger tighten the wing nuts.

HARDWARE

Carriage Bolt

Wing Nut

Door

Wing Nut

1/4"-20 (2)

Carriage Bolt

1/4"-20x1/2" (2)

7/16

(11 mm)

Installation (continued)

To insert or

release wire,

push in tab with

screwdriver tip

La page charge ...

Chamberlain RJO70 Manuel utilisateur

Chamberlain RJO70 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents