Skil TS6307-00 Le manuel du propriétaire

WARNING: To reduce the risk of injury, the user must read and understand the

Owner’s Manual before using this product. Save these instructions for future reference.

AVERTISSEMENT : Afin de réduire les risques de blessure, l’utilisateur doit lire et

comprendre le guide d’utilisation avant d’utiliser cet article. Conservez le présent guide

afin de pouvoir le consulter ultérieurement.

ADVERTENCIA : Para reducir el riesgo de lesiones, el usuario debe leer y comprender

el Manual del operador antes de utilizar este producto. Guarde estas instrucciones para

consultarlas en caso sea necesario.

Owner’s Manual

Guide d’utilisation

Manual del propietario

Table Saw

Scie à table

Sierra de mesa

For Customer Service

Pour le service à la clientèle

Servicio al cliente

1-877-SKIL-999

OR

www.skil.com

Model/ Modelo/ Modèle: TS6307-00

HEIGH T

+

2

0

15

30

45

22.5

BLADE ROTATION

2

TABLE OF CONTENTS

General Power Tool Safety Warnings .............................3-4

Table Saw Safety Warnings .....................................4-8

Additional Safety Rules ..........................................8

Symbols ....................................................9-12

Functional Descriptions and Specications ...................... 13-15

Assembly Instructions .......................................15-24

Adjustments ................................................ 25-31

Basic Table Saw Operation ....................................32-46

Storage and Transportation ...................................47-49

Maintenance ................................................ 50-52

Troubleshooting ............................................52-53

Limited Warranty of SKIL Consumer Bench Top Power Tools ..........54

WARNING

•

Some dust created by power sanding, sawing, grinding, drilling and other construction

activities contains chemicals known to the State of California to cause cancer, birth defects

or other reproductive harm. Some examples of these chemicals are:

–

Lead from lead-based paints.

–

Crystalline silica from bricks, cement, and other masonry products.

–

Arsenic and chromium from chemically-treated lumber.

•

Your risk from these exposures varies, depending upon how often you do this type of work.

To reduce your exposure to these chemicals:

–

Work in a well-ventilated area.

–

Work with approved safety equipment, such as dust masks that are specially designed to

lter out microscopic particles.

–

Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and

other construction activities. Wear protective clothing and wash exposed areas with soap

and water. Allowing dust to get into your mouth or eyes or to lie on the skin may promote

absorption of harmful chemicals.

3

GENERAL POWER TOOL SAFETY WARNINGS

WARNING

Read all safety warnings, instructions, illustrations and specications

provided with this power tool.

Failure to follow all instructions listed

below may result in electric shock, re and/or serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE

REFERENCE.

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or

battery-operated (cordless) power tool.

Work area safety

Keep work area clean and well lit

. Cluttered or dark areas invite accidents.

Do not operate power tools in explosive atmospheres, such as in the presence of

ammable liquids, gases or dust.

Power tools create sparks which may ignite the dust or

fumes.

Keep children and bystanders away while operating a power tool.

Distractions can cause

you to lose control.

Electrical safety

Power tool plugs must match the outlet. Never modify the plug in any way. Do not use

any adapter plugs with earthed (grounded) power tools.

Unmodied plugs and matching

outlets will reduce risk of electric shock.

Avoid body contact with earthed or grounded surfaces, such as pipes, radiators,

ranges and refrigerators.

There is an increased risk of electric shock if your body is earthed

or grounded.

Do not expose power tools to rain or wet conditions.

Water entering a power tool will

increase the risk of electric shock.

Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power

tool. Keep cord away from heat, oil, sharp edges or moving parts.

Damaged or entangled

cords increase the risk of electric shock.

When operating a power tool outdoors, use an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces the risk of electric shock.

If operating a power tool in a damp location is unavoidable, use a ground fault circuit

interrupter (GFCI) protected supply.

Use of a GFCI reduces the risk of electric shock.

Personal safety

Stay alert, watch what you are doing and use common sense when operating a power

tool. Do not use a power tool while you are tired or under the inuence of drugs,

alcohol or medication.

A moment of inattention while operating power tools may result in

serious personal injury.

Use personal protective equipment. Always wear eye protection.

Protective equipment

such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for

appropriate conditions will reduce personal injuries.

Prevent unintentional starting. Ensure the switch is in the off-position before

connecting to power source and/or battery pack, picking up or carrying the tool.

Carrying power tools with your nger on the switch or energising power tools that have the

switch on invites accidents.

Remove any adjusting key or wrench before turning the power tool on.

A wrench or a

key left attached to a rotating part of the power tool may result in personal injury.

Do not overreach. Keep proper footing and balance at all times.

This enables better

control of the power tool in unexpected situations.

4

Dress properly. Do not wear loose clothing or jewelry. Keep your hair and clothing

away from moving parts.

Loose clothes, jewelry or long hair can be caught in moving parts.

If devices are provided for the connection of dust extraction and collection facilities,

ensure these are connected and properly used.

Use of dust collection can reduce dust-

related hazards.

Do not let familiarity gained from frequent use of tools allow you to become complacent

and ignore tool safety principles.

A careless action can cause severe injury within a fraction

of a second.

Power tool use and care

Do not force the power tool. Use the correct power tool for your application.

The correct

power tool will do the job better and safer at the rate for which it was designed.

Do not use the power tool if the switch does not turn it on and off.

Any power tool that

cannot be controlled with the switch is dangerous and must be repaired.

Disconnect the plug from the power source and/or remove the battery pack, if

detachable, from the power tool before making any adjustments, changing accessories,

or storing power tools.

Such preventive safety measures reduce the risk of starting the

power tool accidentally.

Store idle power tools out of the reach of children and do not allow persons unfamiliar

with the power tool or these instructions to operate the power tool.

Power tools are

dangerous in the hands of untrained users.

Maintain power tools and accessories. Check for misalignment or binding of moving

parts, breakage of parts and any other condition that may affect the power tool’s

operation. If damaged, have the power tool repaired before use.

Many accidents are

caused by poorly maintained power tools.

Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to control.

Use the power tool, accessories and tool bits etc. in accordance with these instructions,

taking into account the working conditions and the work to be performed.

Use of the

power tool for operations different from those intended could result in a hazardous situation.

Keep handles and grasping surfaces dry, clean and free from oil and grease.

Slippery

handles and grasping surfaces do not allow for safe handling and control of the tool in

unexpected situations.

Service

Have your power tool serviced by a qualied repair person using only identical

replacement parts.

This will ensure that the safety of the power tool is maintained.

TABLE SAW SAFETY WARNINGS

Guarding related warnings

Keep guards in place. Guards must be in working order and be properly mounted.

A

guard that is loose, damaged, or is not functioning correctly must be repaired or replaced.

Always use saw blade guard, riving knife and anti-kickback device for every through-

cutting operation.

For through-cutting operations where the saw blade cuts completely

through the thickness of the workpiece, the guard and other safety devices help reduce the

risk of injury.

Immediately reattach the guarding system after completing an operation (such as

rabbeting, dadoing or resawing cuts) which requires removal of the guard, riving knife

and/or anti-kickback device.

The guard, riving knife, and anti-kickback device help to reduce

the risk of injury.

5

Make sure the saw blade is not contacting the guard, riving knife or the workpiece

before the switch is turned on.

Inadvertent contact of these items with the saw blade could

cause a hazardous condition.

Adjust the riving knife as described in this instruction manual.

Incorrect spacing,

positioning and alignment can make the riving knife ineffective in reducing the likelihood of

kickback.

For the riving knife and anti-kickback device to work, they must be engaged in the

workpiece.

The riving knife and anti-kickback device are ineffective when cutting workpieces

that are too short to be engaged with the riving knife and anti-kickback device. Under these

conditions a kickback cannot be prevented by the riving knife and antikickback device.

Use the appropriate saw blade for the riving knife.

For the riving knife to function properly,

the saw blade diameter must match the appropriate riving knife and the body of the saw blade

must be thinner than the thickness of the riving knife and the cutting width of the saw blade

must be wider than the thickness of the riving knife.

Cutting procedures warnings

DANGER

Never place your ngers or hands in the vicinity or in line with the saw

blade.

A moment of inattention or a slip could direct your hand towards the

saw blade and result in serious personal injury.

Feed the workpiece into the saw blade or cutter only against the direction of rotation.

Feeding the workpiece in the same direction that the saw blade is rotating above the table

may result in the workpiece, and your hand, being pulled into the saw blade.

Never use the miter gauge to feed the workpiece when ripping and do not use the rip

fence as a length stop when cross-cutting with the miter gauge.

Guiding the workpiece

with the rip fence and the miter gauge at the same time increases the likelihood of saw blade

binding and kickback.

When ripping, always apply the workpiece feeding force between the fence and the

saw blade. Use a push stick when the distance between the fence and the saw blade is

less than 150 mm, and use a push block when this distance is less than 50 mm.

“Work

helping” devices will keep your hand at a safe distance from the saw blade.

Use only the push stick provided by the manufacturer or constructed in accordance

with the instructions.

This push stick provides sufcient distance of the hand from the saw

blade.

Never use a damaged or cut push stick.

A damaged push stick may break causing your

hand to slip into the saw blade.

Do not perform any operation “freehand”. Always use either the rip fence or the miter

gauge to position and guide the workpiece.

”Freehand” means using your hands to

support or guide the workpiece, in lieu of a rip fence or miter gauge. Freehand sawing leads to

misalignment, binding and kickback.

Never reach around or over a rotating saw blade.

Reaching for a workpiece may lead to

accidental contact with the moving saw blade.

Provide auxiliary workpiece support to the rear and/or sides of the saw table for long

and/or wide workpieces to keep them level.

A long and/or wide workpiece has a tendency

to pivot on the table’s edge, causing loss of control, saw blade binding and kickback.

Feed workpiece at an even pace. Do not bend or twist the workpiece. If jamming occurs,

turn the tool off immediately, unplug the tool then clear the jam.

Jamming the saw blade

by the workpiece can cause kickback or stall the motor.

Do not remove pieces of cut-off material while the saw is running.

The material may

become trapped between the fence or inside the saw blade guard and the saw blade pulling

your ngers into the saw blade. Turn the saw off and wait until the saw blade stops before

removing material.

6

Use an auxiliary fence in contact with the tabletop when ripping workpieces less than

2 mm thick.

A thin workpiece may wedge under the rip fence and create a kickback.

Kickback causes and related warnings

Kickback is a sudden reaction of the workpiece due to a pinched, jammed saw blade or

misaligned line of cut in the workpiece with respect to the saw blade or when a part of the

workpiece binds between the saw blade and the rip fence or other xed object.

Most frequently during

kickback

, the workpiece is lifted from the table by the rear portion of

the saw blade and is propelled towards the operator.

Kickback is the result of saw misuse and/or incorrect operating procedures or conditions and

can be avoided by taking proper precautions as given below.

Never stand directly in line with the saw blade. Always position your body on the same

side of the saw blade as the fence.

Kickback may propel the workpiece at high velocity

towards anyone standing in front and in line with the saw blade.

Never reach over or in back of the saw blade to pull or to support the workpiece.

Accidental contact with the saw blade may occur or kickback may drag your ngers into the

saw blade.

Never hold and press the workpiece that is being cut off against the rotating saw blade.

Pressing the workpiece being cut off against the saw blade will create a binding condition and

kickback.

Align the fence to be parallel with the saw blade.

A misaligned fence will pinch the

workpiece against the saw blade and create kickback.

Use a featherboard to guide the workpiece against the table and fence when making

non-through cuts such as rabbeting, dadoing or resawing cuts.

A featherboard helps to

control the workpiece in the event of a kickback.

Use extra caution when making a cut into blind areas of assembled workpieces.

The

protruding saw blade may cut objects that can cause kickback.

Support large panels to minimise the risk of saw blade pinching and kickback.

Large

panels tend to sag under their own weight. Support(s) must be placed under all portions of the

panel overhanging the tabletop.

Use extra caution when cutting a workpiece that is twisted, knotted, warped or does not

have a straight edge to guide it with a miter gauge or along the fence.

A warped, knotted,

or twisted workpiece is unstable and causes misalignment of the kerf with the saw blade,

binding and kickback.

Never cut more than one workpiece, stacked vertically or horizontally.

The saw blade

could pick up one or more pieces and cause kickback.

When restarting the saw with the saw blade in the workpiece, centre the saw blade in

the kerf so that the saw teeth are not engaged in the material.

If the saw blade binds, it

may lift up the workpiece and cause kickback when the saw is restarted.

Keep saw blades clean, sharp, and with sufcient set. Never use warped saw blades

or saw blades with cracked or broken teeth.

Sharp and properly set saw blades minimise

binding, stalling and kickback.

Table saw operating procedure warnings

Turn off the table saw and disconnect the power cord when removing the table insert,

changing the saw blade or making adjustments to the riving knife, antikickback device

or saw blade guard, and when the machine is left unattended.

Precautionary measures

will avoid accidents.

Never leave the table saw running unattended. Turn it off and don’t leave the tool until it

comes to a complete stop.

An unattended running saw is an uncontrolled hazard.

7

Locate the table saw in a well-lit and level area where you can maintain good footing

and balance. It should be installed in an area that provides enough room to easily

handle the size of your workpiece.

Cramped, dark areas, and uneven slippery oors invite

accidents.

Frequently clean and remove sawdust from under the saw table and/or the dust

collection device.

Accumulated sawdust is combustible and may self-ignite.

The table saw must be secured.

A table saw that is not properly secured may move or tip

over.

Remove tools, wood scraps, etc. from the table before the table saw is turned on.

Distraction or a potential jam can be dangerous.

Always use saw blades with correct size and shape (diamond versus round) of arbour

holes.

Saw blades that do not match the mounting hardware of the saw will run off-centre,

causing loss of control.

Never use damaged or incorrect saw blade mounting means such as anges, saw blade

washers, bolts or nuts.

These mounting means were specially designed for your saw, for

safe operation and optimum performance.

Never stand on the table saw, do not use it as a stepping stool.

Serious injury could occur

if the tool is tipped or if the cutting tool is accidentally contacted.

Make sure that the saw blade is installed to rotate in the proper direction. Do not use

grinding wheels, wire brushes, or abrasive wheels on a table saw.

Improper saw blade

installation or use of accessories not recommended may cause serious injury.

Double Insulated Tools

Double insulation is a design concept used in electric power tools which eliminates the

need for the three wire grounded power cord and grounded power supply system. It is a

recognized and approved system by Underwriter’s Laboratories, CSA and Federal OSHA

authorities.

WARNING

Servicing of a tool with double insulation requires care and knowledge of

the system and should be performed only by a qualied service technician.

WARNING

WHEN SERVICING, USE ONLY IDENTICAL REPLACEMENT PARTS.

WARNING

POLARIZED PLUGS. To reduce the risk of electrical shock, your tool is

equipped with a polarized plug (one blade is wider than the other), this

plug will t in a polarized outlet only one way. If the plug does not t fully in the outlet, reverse

the plug. If it still does not t, contact a qualied electrician to install the proper outlet. To

reduce the risk of electrical shock, do not change the plug in any way.

Extension Cords

WARNING

Replace damaged cords immediately.

Use of damaged cords can shock,

burn or electrocute.

WARNING

If an extension cord is necessary, a cord with adequate size conductors

should be used to prevent excessive voltage drop, loss of power or

overheating. The table shows the correct size to use, depending on cord length and nameplate

amperage rating of the tool. If in doubt, use the next heavier gauge. Always use U.L. and CSA

listed extension cords.

8

RECOMMENDED SIZES OF EXTENSION CORDS 120 VOLT

ALTERNATING CURRENT TOOLS

Tool's Ampere

Rating

Cord Size in A.W.G. Wire Sizes in mm

2

Cord Length in Feet Cord Length in Meters

25 50 100 150 15 30 60 120

3-6 18 16 16 14 0.75 0.75 1.5 2.5

6-8 18 16 14 12 0.75 1.0 2.5 4.0

8-10 18 16 14 12 0.75 1.0 2.5 4.0

10-12 16 16 14 12 1.0 2.5 4.0 —

12-16 14 12 — — — — — —

NOTE:

The smaller the gauge number, the heavier the cord.

ADDITIONAL SAFETY RULES

MAKE WORKSHOP CHILD-PROOF

with padlocks, master switches.

Make sure the oor is clean and non-slippery or non-skid where the table saw is set up.

If you cannot control your motion, you cannot control the work.

Use only recommended accessories.

Use only accessories recommended by the

manufacturer of your model. Other accessories may be hazardous.

Do not use any blade or other cutting tool marked for an operating speed less than

4600 R.P.M.

Risk of serious injury.

Ensure that blade or other cutting tool, washers and arbor nut are installed properly.

Reference instructions for removal and installation of the blade.

Never operate the saw unless the proper insert is installed.

Make sure the table insert is ush

or slightly below the table surface at the front and ush to slightly above at the rear of insert.

Always inspect table saw prior to every use.

If any part of your saw is missing,

malfunctioning, or has been damaged or broken (such as the motor switch or other operating

control, a safety device, or the power cord), cease operating immediately until the particular

part is properly repaired or replaced.

Plastic and composition (like hardboard) materials may be cut on your saw. However,

since these are usually quite hard and slippery, the anti-kickback pawls may not stop a

kickback.

Therefore, be especially attentive to following proper set-up and cutting procedures

for ripping. Do not stand, or permit anyone else to stand, in line with a potential kickback.

Use extra caution when the guard assembly is removed for resawing, dadoing,

rabbeting or molding.

Replace the guard as soon as that operation is completed.

Use auxiliary facing on miter gauge to increase stability and control.

Crosscutting

operations are more conveniently worked and with greater safety if an auxiliary wood facing

board is attached to the miter gauge. See “Rip Fence Auxiliary Facing.”

Avoid awkward operations and hand positions.

Where a sudden slip could cause ngers

or hand to move into the sawblade or other cutting tool.

If you stall or jam the sawblade in the workpiece, turn saw “OFF” and unplug the tool,

remove the workpiece from the sawblade, and check to see if the sawblade is parallel to

the table slots or grooves and if the spreader is in proper alignment with the sawblade.

If ripping at the time, check to see if the rip fence is parallel with the sawblade. Readjust as

indicated.

Think Safety. Safety is a combination of operator common sense and alertness at all times

when the table saw is being used.

9

SYMBOLS

Safety Symbols

The purpose of safety symbols is to attract your attention to possible dangers. The safety

symbols and the explanations with them deserve your careful attention and understanding.

The symbol warnings do not, by themselves, eliminate any danger. The instructions and

warnings they give are no substitutes for proper accident prevention measures.

WARNING

Be sure to read and understand all safety instructions in this

Operator’s

Manual, including all safety alert symbols such as “

DANGER

,”

“

WARNING

,” and “

CAUTION

” before using this tool. Failure to following all instructions listed

below may result in electric shock, re, and/or serious personal injury.

The denitions below describe the level of severity for each signal word. Please read the manual

and pay attention to these symbols.

This is the safety alert symbol. It is used to alert you to potential

personal injury hazards. Obey all safety messages that follow this

symbol to avoid possible injury or death.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could

result in death or serious injury.

CAUTION

CAUTION, used with the safety alert symbol, indicates a hazardous

situation which, if not avoided, will result in minor or moderate injury.

Damage Prevention and Information Messages

These inform the user of important information and/or instructions that could lead to equipment

or other property damage if they are not followed. Each message is preceded by the word

“NOTICE”, as in the example below:

NOTICE:

Equipment and/or property damage may result if these instructions are not followed.

WARNING

The operation of any power tools can result in

foreign

objects being thrown into your eyes, which can result

in severe eye damage. Before beginning power tool operation, always

wear safety goggles or safety glasses with side shields and a full face

shield when needed. We recommend a Wide Vision Safety Mask for use

over eyeglasses or standard safety glasses with side shields. Always use

eye protection which is marked to comply with ANSI Z87.1.

10

SYMBOLS (CONTINUED)

IMPORTANT:

Some of the following symbols may be used on your tool. Please study them

and learn their meaning. Proper interpretation of these symbols will allow you to operate the

tool better and safer.

Symbol Name Designation/Explanation

V Volts Voltage (potential)

A Amperes Current

Hz Hertz Frequency (cycles per second)

W Watt Power

kg Kilograms Weight

min Minutes Time

s Seconds Time

Wh Watt-hours Battery capacity

Ah Ampere-Hours Battery capacity

Ø Diameter Size of drill bits, grinding wheels, etc.

n

0

No load speed Rotational speed, at no load

n Rated speed Maximum attainable speed

…/min

Revolutions or reciprocation

per minute

Revolutions, strokes, surface speed,

orbits, etc. per minute

0 Off position Zero speed, zero torque...

1,2,3,…

I,II,III,

Selector settings

Speed, torque or position settings. Higher

number means greater speed

Innitely variable selector

with off

Speed is increasing from 0 setting

Arrow Action in the direction of arrow

Alternating current Type or a characteristic of current

Direct current Type or a characteristic of current

Alternating or direct current Type or a characteristic of current

Class II tool

Designates Double Insulated Construction

tools.

Earthing terminal Grounding terminal

Li-ion RBRC seal

Designates Li-ion battery recycling

program

Ni-Cad RBRC seal

Designates Ni-Cad battery recycling

program

11

Symbol Name Designation/Explanation

Read manual symbol Alerts user to read manual

Wear eye protection symbol

Always wear safety goggles or safety

glasses with side shields and a full face

shield when operating this product.

Wear a mask

Recommendation for the operator to wear

dust mask .

Wear ear protection

Recommendation for the operator to wear

hearing protection .

12

SYMBOLS (CERTIFICATION INFORMATION)

IMPORTANT:

Some of the following symbols for certication information may be used on your

tool. Please study them and learn their meaning. Proper interpretation of these symbols will

allow you to operate the tool better and safer.

Symbol Designation/Explanation

This symbol designates that this tool is listed by Underwriters Laboratories.

This symbol designates that this tool is recognized by Underwriters

Laboratories.

This symbol designates that this tool is listed by Underwriters

Laboratories, to United States and Canadian Standards.

This symbol designates that this tool is listed by the Canadian

Standards Association.

This symbol designates that this tool is listed by the Canadian

Standards Association, to United States and Canadian Standards.

This symbol designates that this tool is listed by the Intertek Testing

Services, to United States and Canadian Standards.

This symbol designates that this tool complies to NOM Mexican

Standards.

13

FUNCTIONAL DESCRIPTIONS AND SPECIFICATIONS

Fig. 1

1

HEIG HT

+

2

0

15

30

45

22.5

BLADE ROTATION

2 4 5 6

7

9

10

1213

22 21

25 24 23

18

15

16

17

1114

8

3

20 19

14

1. Power Switch

Switch incorporates a hole for use with a

padlock to prevent accidental starting.

2. Elevation Wheel

Elevates or lowers the blade. Also used to

tilt the blade -2° to 47 °. The cutting capacity

at 0° is 3-1/2”. The cutting capacity at 45° is

2-1/2”.

3. Blade-bevel-lock Lever

Locks the blade to desired bevel angle.

4. Blade-bevel Scale

Shows the degree to which the blade is tilted.

Total range of the bevel is -2° to 47°.

5. Base

Supports the table saw. Includes integrated

carry handle.

6. Push Stick & Storage

Allows you to rip smaller pieces of stock with

a greater level of safety.

7. Rail-driving Wheel Knob

Drives the rail to move it from side to side.

8. Rail-lock Lever

Allows you to lock the fence at desired

distances.

9. Work Support/Auxiliary Fence

Provides support for wider workpieces when

extending the fence beyond the table and for

thinner workpiece with thickness not more

than 3/4” when not extending the fence.

10. Rip Fence

Provides an auxiliary support (in the lower

position) and over-the-table support (upper

position). Securely attaches to rails in 3

positions with lock latches on both ends.

11. Rip-fence Scale

Shows the distance from the blade to the rip

fence 14 inches to left, 25.5 inches to right.

12. Smart Guard System

Consists of three key elements: Riving

Knife (Spreader), Anti-Kickback Device, and

Main Barrier Guard. All of these are part

of a modular system that requires no tools

to assemble or disassemble. This Guard

System must always be in place and working

properly for all through sawing cuts.

13. Table Insert

Removable for removing or installing a blade

or other cutting tools.

14. Miter Gauge

Head can be locked in the desired position

for crosscutting or mitering by tightening the

lock knob. ALWAYS SECURELY LOCK THE

HEAD WHEN IN USE.

15. Table

Provides large working surface to support

the workpiece.

16. Cord Wrap&Storage

Allows you to easily secure the cord so it’s

out of the way when transporting or storing.

17. Miter Gauge Storage

Storage location for the miter gauge when

not in use, or when transporting or storing

the table saw.

18. Rip-fence Storage

Storage location for the rip fence when

transporting or storing the table saw.

19. Dust-Chute Elbow & Storage

Storage location for the dust-chute elbow

when not in use, or when transporting or

storing the table saw.

20. Anti-Kickback Device Storage

Storage location for the anti-kickback device

when not in use, or when transporting or

storing the table saw.

21. Dust Port/Vacuum Hook-Up

Removable to clear any large pieces of wood

trapped inside. Always check to ensure that

the dust port is securely fastened to the table

saw before use. Attach a 2-1/2” vacuum hose

into the dust port for convenient sawdust

removal.

22. Stand

Allows table saw to be raised during use.

23. Main-barrier-guard Storage

Storage location for the Main Barrier Guard

when not in use, or when transporting or

storing the table saw.

24. Wrench & Storage

Wrench for the removal and installation of

saw blades.

25. Carrying Handle

Allows you to carry the table saw with one

hand when it is not in use.

15

Specications

Rated Input

120 Vac, 60 Hz ,15A

No Load Speed (RPM)

4600/min

Blade Size

10’’(254mm)

Arbor

5/8"

Bevel angle range

-2° - 47°

Cutting Depth at 90°

3-1/2"

Cutting Depth at 45°

2-1/2"

Max. Dado Cutting Width

5/8"

Max. Rip Length To Right

Of Blade

25.5"

Max. Rip Length To Left Of

Blade

14’’

ASSEMBLY INSTRUCTIONS

WARNING

To avoid injury from unexpected starting or electrical shock during

unpacking and setting up, do not plug the power cord into a source

of power.

This cord must remain unplugged whenever you are assembling or making

adjustments to the table saw with stand.

Model TS6307-00 Table Saw and stand is shipped completely in one carton. To make the

assembly of the stand easier, place the table saw with the table surface towards the ground.

Separate all parts from the packing materials and check each one against the illustration and

the list of Loose Parts to make certain that all items are accounted for before discarding any

packing material (Fig. 2).

WARNING

If any parts are missing, do not attempt to assemble the table saw,

plug in the power cord or turn the switch on until the missing parts

are obtained and are installed correctly.

TABLE OF LOOSE PARTS

ITEM DESCRIPTION QTY.

1 Dust-Chute Elbow 1

2 Barrier-Guard Assembly 1

3 Anti-Kickback Device 1

4 Miter Gauge 1

5 Push Stick 1

6 Rip Fence 1

7

Drive Knob with Washer

and Hex Screw

1

Fig. 2

1

2

6

3

4 5 7

16

Remove Cable Tie and Foam

Block

(Used for shipping purpose only)

With the table surface on the ground, locate

the cable tie that anchors the motor/blade

assembly to the base. Using scissors or wire

cutters, cut and remove the cable tie. Release

the blade bevel lock lever, tilt the blade to 45

degrees, then remove the foam block located

between the motor housing and the table.

(Fig.3)

NOTE:

The foam block must be removed

before the blade is raised to avoid possible

damage to the blade.

Fig. 3

Remove Styrofoam

Block

17

Tools needed for assembly and adjustment

WARNING

Disconnect the plug from the power source before performing any

assembly, adjustment or repair to avoid possible injury.

Blade Wrenches (supplied)

Framing Square

(not supplied)

3/4” board with

straight top edge

Drawn line

No gap or

overlap

1.Position square

and draw a light line

2.Flip square (shown in

dotted position)

3.Check edge of ipped

square against the drawn

line. There should be no gap

or overlap at the bottom end.

10mm Wrench

(not supplied)

Double-Ended Allen

Wrench, 6mm Hex,

with PH2 Phillips end

(supplied)

COMBINATION SQUARE MUST BE TRUE

Combination Square

(not supplied)

2.5mm/5mm Hex

Wrench (not supplied)

Fig. 4

18

Unfolding The Stand Legs Before Assembly

WARNING

To reduce the risk of personal injury, do not operate table saw until

you have read and understand the followings:

•

The table saw is integrated with the stand when shipped. Check the stand to make

sure that it is still securely fastened to the table saw before any operation. A loose

stand is unstable and may shift in use and cause serious injury.

•

Do not stand on the table saw stand or use it as a ladder or scaffolding.

•

Do not use table saw if the stand tips, slides, or moves in any way.

•

Before operating the table saw, ensure that the entire table-saw/stand assembly is

secure and placed on solid, level surface.

•

Use only SKIL replacement parts for the stand. Any others may create a hazard.

1. Place the table saw on a clean level surface with the tabletop facing the ground (Fig.5a).

2. Press the red button of the stand while unfolding the stand leg. Do not release the red

button until the stand leg has been folded completely (Fig.5a).

3. Repeat the above operation to unfold the other three stand legs in turn.

4. Lift the carrying handle until the table saw is vertical (Fig.5b).

Fig. 5a

Fig. 5b

Installing The Drive Knob (Fig.6)

Attach the drive knob onto the mounting hole.

While holding the drive knob to prevent it from

moving, install the included hex screw and

washer into the drive knob and the mounting

hole , then use the Double-Ended Allen

Wrench (included) to secure the hex screw in

place.

Fig. 6

Mounting

Hole

Drive Knob

Washer

Hex Screw

19

Removing and Installing The

Table Insert (Fig.7)

To remove table insert, press the button with

your thumb and place your index nger into the

nger hole to lift and pull the table insert out

toward the front of the saw.

To install table insert, align and insert the two

tabs on table insert with the two pockets in the

tabletop and pivot the table insert downwards.

Verify that the table insert is seated.

NOTICE:

The table insert is adjustable and,

therefore, can change over time. Verify that the

table insert is set correctly before every use.

If adjustment is needed, follow the “Adjusting

The Table Insert” instructions.

Attaching the Smart Guard System

WARNING

To prevent personal

injury, always disconnect

the plug from the power source before

attaching or removing the Smart Guard

System.

Positioning the riving knife

1. Remove the table insert (see “Removing

and Installing The Table Insert ”).

2. Raise the blade as high as it will go by

turning the elevation wheel clockwise and

set it perpendicular to the table (0° on bevel

scale) (Fig. 8).

3. Rotate the release lever clockwise, so that

it points upward (Fig. 8).

4. Pull the riving knife toward the release

lever to disengage the upper hole of the

riving knife from the pin (Fig.9).

Fig. 7

1

2

Fig. 8

B

Release Lever

Fig. 9

Upper Hole of the Riving Knife

Button

Finger Hole

Table Insert

Riving Knife

20

5. Slide the riving knife up to its highest position so that it is directly over the center of the

blade (Fig. 10).

6. Align and engage the lowest hole in riving knife with the pin, then lock the release lever by

rotating it counterclockwise. Push/pull on the riving knife to verify that it is locked in place

(Fig. 10).

7. Replace the table insert (Fig.11), see “Removing and Installing The Table Insert ”).

1

2

Fig. 10

Fig. 11

Attaching the main barrier guard

WARNING

Before attaching the main

barrier guard, make sure to

slide the riving knife to its highest position.

Otherwise, the main barrier guard will not be

positioned rightly in place and could increase the

risk of serious personal injury.

1. With one hand, hold the front of the main

barrier guard by the mounting fork. With the

other hand, lift the guard-release lever up

(Fig. 12).

2. Lower the rear of the main barrier guard and

completely slide the cross bar into the middle

notch on top of the riving knife

(Fig. 12).

Fig. 12

Guard-Release Lever

Mounting Fork

Guard

Barriers

Cross Bar

Middle Notch

La page charge ...

Skil TS6307-00 Le manuel du propriétaire

Skil TS6307-00 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents