Kodak C 750 Manuel utilisateur

Catégorie
Caméras de cinéma
Taper
Manuel utilisateur
Consumer Imaging
EASTMAN KODAK COMPANY
Rochester, NY 14650
© Eastman Kodak Company, 2000
Pt. No. 919 5504
Printed in U.S.A.
Kodak
C750 Zoom
Camera
Unfold the front and back flaps of this manual to view the camera’s parts.
Unfold the front and back flaps of this manual to view the camera’s parts.
ENGLISH/ESPAÑOL/FRANÇAIS
1 Shutter button
2 Zoom dial
3 Format-selector switch
4 Lens cover/flash
5 Light sensor
6 Viewfinder
7 Auto-focus sensors
8 Lens
9 Red-eye-reduction/
self-timer lamp
10 Film-door lever
CAMERA IDENTIFICATION
1
2
3
4
5
6
7
8
9
10
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE: Your model camera has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
provide reasonable protection against interference in residential use. The camera
generates, uses and can radiate radio frequency energy and, if not used in
accordance with the instructions, may cause interference to radio
communications. There is no guarantee that interference will not occur. If this
camera does cause interference to radio or television reception, which can be
determined by turning the camera off and on, you may reduce the interference by
the following:
— Reorient or relocate the receiving antenna.
— Increase the separation between the camera and the receiver.
— Consult the dealer or an experienced radio/television technician for help.
Changes or modifications not approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Camera Identification LCD Panel
11 Battery door
12 Viewfinder eyepiece
13 Flash/camera-
ready lamp
14 LCD panel
15 Flash-mode button
16 Mode button
17 Strap post
18 Film door
19 Tripod socket
20 Mid-roll-change
(MRC) button
21 Enter/self-timer
button
22 Select button
23 Menu button
24 Auto-flash indicator
25 Red-eye-reduction
indicator
26 Fill-flash indicator
27 Flash-off indicator
28 Mode-selector arrow
29 PM indicator
30 ISO film-
speed display
31 Title/print-quantity
display
32 Self-timer indicator
33 Spot-focus icon
34 Nightview icon
35 Portrait icon
36 Infinity-focus icon
37 Frame counter
38 Film-presence
indicator
39 Date/time display
40 Battery symbol
12
13
14
15
16
17
18
19
11
20
21
22
23
PRINT
PM
ISO
QTY
TITLEROLL
AUTO FILL
26 27
28
30
31
32
29
333435
36
37
38
39
40
24
25
This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations
1
KODAK ADVANTIX
C750 Zoom Camera
Welcome to the world of the Advanced Photo System!
And thank you for buying this KODAK ADVANTIX Camera.
NEED HELP WITH YOUR CAMERA?
Go to our Web site at http://www.kodak.com (for US) or
http://www.kodak.ca (for Canada) or call:
Kodak (USA only) from 9:00 a.m. to 7:00 p.m. (Eastern time) Monday through
Friday at 1 (800) 242-2424.
Kodak (Canada only) from 8:00 a.m. to 5:00 p.m. (Eastern time) Monday
through Friday at 1 (800) 465-6325, ext. 36100; for the Toronto area,
call (416) 766-8233, ext. 36100.
When you call, please have your camera available.
For warranty purposes, please keep your sales receipt as proof
of the date of purchase.
© Eastman Kodak Company, 2000
ENGLISH
2
CONTENTS
ADVANCED PHOTO SYSTEM
FEATURES AVAILABLE WITH
THIS CAMERA ......................................3
GETTING STARTED .................................5
Loading the battery ..............................5
Setting the language............................6
List of languages ..................................7
Date and time imprinting.......................8
Setting the date and time.....................8
ATTACHING THE STRAP .........................9
CONTROL-BUTTON ACTUATOR .......... 10
LOW-BATTERY INDICATOR .................. 10
BATTERY TIPS ...................................... 10
POWER SHUT-OFF ................................ 11
LOADING THE FILM .............................. 11
TAKING PICTURES ............................... 13
Typical print sizes (formats) ................ 14
Using the focus lock........................... 15
Tips for better pictures ....................... 15
USING THE ZOOM LENS ...................... 16
TAKING FLASH PICTURES .................. 17
Flash-to-subject distance................... 18
Flash/warning-lamp signals ............... 18
FLASH MODES ..................................... 19
Auto flash with
red-eye reduction........................... 19
Fill flash............................................... 19
Flash off ............................................. 19
Auto flash without
red-eye reduction........................... 20
Selecting the flash modes ................. 20
SPECIAL-OPTION MODES ................... 20
Infinity-focus mode............................. 21
Portrait mode...................................... 21
Nightview mode.................................. 21
Center-spot focus mode .................... 21
Selecting the special-option modes .. 21
USING THE SELF-TIMER ...................... 23
TITLE IMPRINTING ................................ 24
TITLE-SELECT LIST.............................. 24
PRINT-QUANTITY SELECTION (PQS).. 26
ISO FILM-SPEED DISPLAY .................. 26
UNLOADING THE FILM ......................... 27
Automatic rewind................................ 27
Mid-roll change (MRC)........................ 27
CARING FOR YOUR CAMERA .............. 28
TROUBLESHOOTING............................ 29
SPECIFICATIONS .................................. 31
3
Triple format selection
You can take three different size
pictures: Classic (C), Group/HDTV (H),
and Panoramic (P) pictures from the
same film cassette.
The masking inside
the viewfinder changes to match each
format selection.
Date and time/title imprinting
The date, time, and cassette ID
number are printed on the back of your
prints, which makes it easy to organize
pictures and order reprints. You can
choose from one of 41 pre-
programmed titles (12 languages
available) to print on the back of the
prints.
See your photofinisher for a full
description of available services.
Double exposure protection (DEP)
Don’t worry about accidentally re-
exposing your film. Your camera reads
the Film Status Indicator (FSI) on the
film cassette to prevent double
exposures.
Flip flash plus
This system automatically adjusts
to provide just the right light in
any situation. The flash system:
provides extra
red-eye reduction
with the extension of the flip flash and
the red-eye-reduction mode,
automatically turns on for
dimly
lit scenes
,
delivers brighter light for clearer,
more colorful pictures for
distance shots
,
provides softer light for more natural
images for
close-ups
,
automatically
provides fill-in light for
more sparkle and clarity in harshly
lit
portraits
, and
recharges quickly so it is
ready to capture those
spontaneous
peak moments
.
ADVANCED PHOTO SYSTEM FEATURES
AVAILABLE WITH THIS CAMERA
4
Easy, drop-in loading
Easy, drop-in loading is fast and
virtually error-free, eliminating blank
rolls and double exposures. The
camera uses KODAK ADVANTIX Film.
The film cassette, unlike the traditional
35 mm cartridge, communicates the
status of film and becomes the carrier
and storage container for the
processed film.
Picture quality information
exchange (PQix)
This camera records vital scene data
on the film’s magnetic information
strip and communicates that
information to the photo lab to
optimize lighting and color for better-
looking prints.
Mid-roll change (MRC)
You can remove your film in mid-roll
and later reload it and continue taking
pictures. MRC lets you:
switch film speeds in mid-roll to
match scene requirements,
organize by dedicating individual
film rolls to specific subjects, and
share a family camera in which the
members use their own roll of film.
4
3
2
1
Processed Negatives
Fully
Exposed
Partially
Exposed
Unexposed
Film status indicator (FSI)
A highlighted indicator advances from
one symbol to another to identify the
status of the film inside the cassette.
5
GETTING STARTED
Before you take pictures, you need to
load the battery, set the language, and
set the date and time.
Loading the battery
This camera uses one 3-volt lithium
KODAK KCR2 (or equivalent) Battery
that supplies power for all camera
operations.
1. Slide the battery-door latch and lift to
open the battery door (11).
2. Insert the battery into the
battery chamber.
3. Snap the battery door closed.
After you load a new battery into the
camera, reset the date and time.
6
2. Press and hold the menu button (23)
for approximately 4 seconds until
US appears on the LCD panel (14).
When you release the button, the
language code “blinks.”
3. Press the right or left side of the zoom
dial (2) or the select button (22)
to cycle to your selection.
Setting the language
US English is initially set into the memory
of this camera, but you can select
another language (12 options available).
See the table on page 7 for the List of
languages
and the LCD (Liquid Crystal
Display) abbreviated codes.
1. Completely lift up the lens cover/
flash (4) to uncover the lens (8) and to
turn on the camera.
SELECT
MENU
ENTER
P
C
H
7
List of languages
Languages LCD display
American English US
UK English En
German dEU
French FrA
Spanish ESP
Japanese JP
Danish dEn
Finnish FI
Italian I
Norwegian nor
Portuguese P
Swedish S
4. Press the enter/self-timer button (21)
to complete your selection.
g
SELECT
MENU
ENTER
8
Date and time imprinting
Traditional cameras print date and/or
time information directly onto the film.
Your camera uses the film’s magnetic
data-recording capability to record date
and time information, which your
photofinisher can imprint only on the
back of your photographs. This camera
has a quartz clock and automatic
calendar through the year 2099.
Setting the date and time
Choose from three formats:
(month/day/year, day/month/year, or
year/month/day) and time format
(hour/minute) with PM display.
1. Repeatedly press the menu
button (23) to scroll and select the
desired function.
2. Press the select button (22).
The first number(s) in the date- or
time-option mode will “blink.”
3. Press the zoom dial (2) or select
button (22) to change the number(s).
Press the right side of the zoom dial
to increase the number and the left
side to decrease the number.
SELECT
MENU
ENTER
SELECT
MENU
ENTER
9
ATTACHING THE STRAP
1. Insert the shorter looped end of the
strap behind the strap post (17).
2. Thread the longer end of the strap
through the shorter loop.
3. Pull the strap tight.
4. Press the enter/self-timer button (21)
to store the selected number(s) and to
activate the next “blinking” number(s).
5. Follow steps 3 and 4 to continue your
selection or press the enter/self-timer
button again to stop the number(s)
from blinking and to end your
selection.
SELECT
MENU
ENTER
10
CONTROL-BUTTON ACTUATOR
You can use the knob on the clasp of the
camera strap to actuate the small control
buttons on the camera.
LOW-BATTERY INDICATOR
It’s time to replace the battery when—
the battery symbol (40) “blinks”
on the
LCD panel (14),
none of the indicators, except for a
steady battery symbol, appear on the
LCD panel and the shutter button (1)
cannot be operated,
or
the LCD panel is blank when the lens
cover/flash (4) is up.
BATTERY TIPS
Dispose of batteries according to
local and national regulations.
Keep a spare battery with you at
all times.
Read and follow all warnings and
instructions supplied by the battery
manufacturer.
Keep batteries away from children.
Do not try to take apart, recharge or
short circuit the battery, or subject it to
high temperature or fire.
Store batteries in their original
packaging prior to use.
Do not use rechargable batteries.
Remove the battery from the camera
when the camera is not going to be
used for an extended length of time.
In the unlikely event that battery fluid
leaks onto your skin, contact Kodak
Health, Safety and Environment
Information at 1-716-722-5151 in
the U.S.
11
In the unlikely event that battery fluid
leaks inside the camera, U.S.
customers can contact the Kodak
Information Center (KIC) at 1-800-242-
2424. Customers outside the U.S. can
contact their local Kodak Customer
Service representative.
POWER SHUT-OFF
To save battery power, the camera auto-
matically goes into a sleep mode if it is
not operated for more than 2 1/2 minutes.
You can press almost any of the control
buttons, except for the format-selector
switch (3), to awaken the camera. When
the camera is not used for an extended
time, close the lens cover/flash to
completely turn off the camera.
LOADING THE FILM
You can load film into the camera with the
lens cover/flash opened or closed.
1. Rotate the film-door lever (10) to open
the film door (18).
The film door opens only when the
film chamber is empty or the film in
the camera is completely rewound
into the film cassette and the motor
stops running.
N
P
O
E
12
Look for this logo to be certain that the film you buy is
made for this camera.
2. Insert the film cassette completely
into the film chamber. Make sure the
Film Status Indicator (FSI) on the film
cassette is at (#1 position) for a
new cassette or at (#2 position) for
a partially exposed cassette.
Do not force the film cassette
into the film chamber.
3. Close the film door to start the auto-
film advance. The frame counter (37)
on the LCD panel (14) shows the
number of pictures remaining on the
film cassette.
1
2
3
4
Look for this logo to select a certified photofinisher for
developing your film and to assure that you get all the
features of the Advanced Photo System.
13
TAKING PICTURES
You can take Classic (C),
Group/HDTV (H)*
,
and Panoramic (P) pictures on the same
film cassette. See the table on page 14
for Typical print sizes (formats). Your
photo-processing cost may be based on
the format size(s) that you use to
expose the film.
1. Completely lift up the lens cover/
flash (4) to uncover the lens (8)
and to turn on the camera.
* High Definition Television (HDTV) prints are the
same aspect ratio as the TV for CD interface
capabilities.
CH
P
2. Slide the format-selector switch (3) to
select C, H, or P format. The
viewfinder changes to show the
selected field of view.
C
H
P
C
H
P
3. Look through the viewfinder
eyepiece (12) placing the Auto Focus
(AF) brackets on the subject. For a
sharp picture, stand at least 2 ft
(0.6 m) from your subject.
14
Typical print sizes (formats)
CHP
Classic Group (HDTV) Panoramic
3.5 x 5 in. or 4 x 6 in. 3.5 x 6 or 4 x 7 in. 3.5 x 8.5 in. to 4 x 11.5 in.
(88.9 x 127 mm or (88.9 x 152 mm or (88.9 x 216 mm to
102 x 152 mm) 102 x 178 mm) 102 x 292.7 mm)
NOTE: Your photofinisher generally provides 4 x 6, 4 x 7, and 4 x 11.5 in. (102 x 152, 102 x 178, and
102 x 292.7 mm) sizes. Some local printers may offer 3.5 x 5, 3.5 x 6, and 3.5 x 8.5 in.
(88.9 x 127, 88.9 x 152, and 88.9 x 216 mm) sizes.
4. Partially press down the shutter
button (1) until the flash/camera-ready
lamp (13) turns green. Fully press
down the shutter button to take
the picture.
C
H
P
15
AF Circle
Using the focus lock
This camera automatically focuses on
whatever is within the Auto Focus (AF)
brackets of the viewfinder eyepiece. To
get a sharp picture, make sure the AF
brackets are on your main subject. If you
want to take a picture with the subject
positioned outside the AF brackets, use
the focus lock as follows:
1. Place the AF circle on the subject that
you want focused in the picture.
Viewfinder
Viewfinder
Tips for better pictures
Move close enough to your subject so
it fills the viewfinder but not closer
than 2 ft (0.6 m).
Take pictures at the subject’s level.
Kneel down to take pictures of
children and pets.
Hold your camera vertically to capture
tall, narrow subjects, such as
a waterfall, skyscraper, or a single
person.
2. Partially depress and hold the shutter
button (1) to lock the focus position
and wait for the flash/camera-ready
lamp (13) to turn green.
3. While still partially depressing the
shutter button, move the camera until
your subject is where you want
it within the viewfinder eyepiece (12).
4. Fully press down the shutter button to
take the picture.
16
Add interest to your picture by framing
it with a tree branch, a window, or
even the rails of a fence.
Keep the sun behind you. This provides
the best subject illumination.
• Stand at an angle to shiny surfaces
like windows or mirrors to avoid flash
reflection and bright spots in your
pictures.
Turn on all room lights and have your
subject look at the red-eye-reduction
lamp to reduce red eyes in flash
pictures.
USING THE ZOOM LENS
This camera has a motorized-zoom lens
that lets you select the ideal lens-focal
length for taking pictures. When you turn
on the camera, it is initially set to the
wide-angle position.
1. Completely lift up the lens cover/
flash (4) to uncover the lens (8)
and to turn on the camera.
2. Look through the viewfinder
eyepiece (12).
3. Press the right side of the zoom
dial (2) to zoom
closer
to the subject
in the telephoto mode or the left side
to zoom
away
from the subject in the
wide-angle mode.
4. Press the shutter button (1) to take
the picture.
The lens barrel automatically
returns to the wide-angle position
after 2 1/2 minutes.
P
C
H
17
TAKING FLASH PICTURES
In dim light, such as indoors or outdoors
in heavy shade, or on dark overcast
days, you need flash. Your camera
features an automatic flash that fires
when you need it. The special flip-flash
plus system of this camera shortens the
flash duration in close-up pictures. This
enhances your flash pictures and helps
to conserve the battery life.
1. Completely lift up the lens cover/
flash (4) to uncover the lens (8)
and to turn on the camera.
2. Keep the subject within the
recommended distance range for the
speed of film in your camera.
Do not take pictures beyond the
maximum distance or your pictures
will be dark.
3. Partially press down the shutter
button (1).
4. When the flash/camera-ready
lamp (13) glows green, fully press
down the shutter button to take the
picture (see Flash/warning-
lamp signals on page 18).
18
Flash-to-subject distance
ISO Film Wide Tele
Speed (24 mm) (60 mm)
50 2 to 10 ft 2 to 7 ft
(0.6 to 3.0 m) (0.6 to 2.1 m)
100 2 to 14 ft 2 to 10 ft
(0.6 to 4.3 m) (0.6 to 3.0 m)
200 2 to 20 ft 2 to 14 ft
(0.6 to 6.1 m) (0.6 to 4.3 m)
400 2 to 29 ft 2 to 20 ft
(0.6 to 8.8 m) (0.6 to 6.1 m)
800 2 to 41 ft 2 to 28 ft
(0.6 to 12.5 m) (0.6 to 8.5 m)
1600 2 to 57 ft 2 to 39 ft
(0.6 to 17.4 m) (0.6 to 11.9 m)
Flash/warning-lamp signals
Lamp Indicator Situation
Glows green Camera ready for
picture-taking
Glows red Subject between
8 in. (20 cm) and
2 ft (0.6 m) from
camera. Shutter
button locks.
“Blinks” red Flash not
fully charged
Camera movement
Beyond the
flash range
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110

Kodak C 750 Manuel utilisateur

Catégorie
Caméras de cinéma
Taper
Manuel utilisateur

dans d''autres langues