DeWalt Emglo D55153 Manuel utilisateur

D55151, D55152, D55153, D55155

Contractor’s Electric 4 Gallon Hand Carry Air Compressor

Compresseurs d’air portatifs électriques de 4 gallons de classe entrepreneur

Compresor de aire portátil elèctrico de 4 galones para contratistas

INSTRUCTION MANUAL

GUIDE D'UTILISATION

MANUAL DE INSTRUCCIONES

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA

DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO

ANTES DE USAR EL PRODUCTO.

If you have questions or comments, contactus.

Pour toute question ou tout commentaire, nouscontacter.

Si tiene dudas o comentarios,contáctenos.

1-800-4-

DeWALT

• www.

DeWALT

.com

2

English

A. On/Off Switch

B. Air Tank Pressure Gauge

C. Regulated Pressure Gauge

D. Pressure Regulator

E. Quick Connects (if equipped)

F. Check Valve

G. Safety Valve

H. Air Tank Drain Valve

I. Power Cord Wrap

J. Pressure Switch

K. Pump Oil Dipstick

L. Pump Oil Drain Plug

M. Motor Reset

N. Air Intake Filter

Air Compressor

C

NOT A

STEP

D

B

E

K

L

J

D

E

L

M

I

F

B

C

A

G

A

H

K

F

M

N

J

G

FIG. 1

3

English

Speciﬁcations

MODEL

D55151 D55152 D55153 D55155

WEIGHT 56 lbs. (25.4 kg) 65 lbs. (29.5 kg) 58 lbs. (28.3 kg) 61 lbs. (27.7 kg)

HEIGHT 16.75" (425.5 mm) 16.0" (406.4 mm) 16.75" (501.7 mm) 12.5" (317.5 mm)

WIDTH 18.0" (457.2 mm) 18.0" (457.2 mm) 18.0" (457.2 mm) 21.75" (552.5 mm)

LENGTH 15.0 (381 mm) 18.0" (457.2 mm) 15.0 (381 mm) 21.75" (552.5 mm)

AIR TANK CAPACITY (GALLONS) 4.0 (15.1 liters) 4.0 (15.1 liters) 4.0 (15.1 liters) 4.0 (15.1 liters)

APPROX CUT-IN PRESSURE

95 PSI (655 kPa) 95 PSI (655 kPa) 95 PSI (655 kPa) 100 PSI (689.5 kPa)

APPROX. CUT-OUT PRESSURE

125 PSI (861.8 kPa) 125 PSI (861.8 kPa) 125 PSI (861.8 kPa) 125 PSI (861.8 kPa)

SCFM @ 100 PSI (689.5 kPa) 3.2 3.8 3.8 4.5

MOTOR 1.1 hp (continuous) 1.1 hp (continuous) 1.1 hp (continuous) 1.2 hp (continuous)

Volts/Amps/Hertz 120V/12.5 A/60 Hz. 120V/14 A/60 Hz. 120V/14 A/60Hz. 120V/15 A/60Hz.

RPM 3450 3450 3450 3450

Minumum Branch Circuit

Requirement

15 Amp 15 Amp 15 Amp 15 Amp

PUMP OIL CAPACITY 6 oz. (177.4 ml) 12 oz. (354.9 ml) 12 oz. (354.9 ml) 4 oz. (118.3 ml)

DUTY CYCLE 5 MINUTES ON / 5

MINUTES OFF

5 MINUTES ON / 5

MINUTES OFF

5 MINUTES ON / 5

MINUTES OFF

5 MINUTES ON / 5

MINUTES OFF

4

English

Deﬁnitions: Safety Guidelines

The definitions below describe the level of severity

for each signal word. Please read the manual and

pay attention to these symbols.

DANGER: Indicates an imminently hazardous

situation which, if not avoided, will result in death

or seriousinjury.

WARNING: Indicates a potentially hazardous

situation which, if not avoided, could result in death

or seriousinjury.

CAUTION: Indicates a potentially hazardous

situation which, if not avoided, may result in minor or

moderateinjury.

CAUTION: Used without the safety alert symbol

indicates a potentially hazardous situation which, if

not avoided, may result in propertydamage.

PUMP

CYLNDER

AND HEAD

Hot Surfaces

FIG. 2

OUTLET TUBE

CHECK

VALVE

CHECK

VALVE

OUTLET TUBE

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT

THIS OR ANY

DeWALT

TOOL, CALL US TOLL FREE AT:

1-800-4-D

e

WALT (1-800-433-9258)

Important Safety Instructions

WARNING: Do not operate this unit until you read and

understand this instruction manual for safety, operation and

maintenanceinstructions.

WARNING: Some dust created by power sanding, sawing,

grinding, drilling, and other construction activities contains chemicals

known to the State of California to cause cancer, birth defects or other

reproductive harm. Some example of these chemicals are:

• lead from lead-based paints

• crystalline silica from bricks and cement and other masonry

products

• arsenic and chromium from chemically-treated lumber

Your risk from these exposures varies, depending on how often

you do this type of work. To reduce your exposure to these

chemicals: work in a well ventilated area, and work with approved

safety equipment, al ways wear OSHA/MSHA/NIOSH approved,

properly t ting face mask or res pi ra tor when us ing suchtools.

When using air tools, basic safety precautions should always be

followed to reduce the risk of of personalinjury.

WARNING: This product contains chemicals, including lead,

known to the State of California to cause cancer, and birth

defects or other reproductive harm. Wash hands afterhandling.

SAVE THESE INSTRUCTION

5

English

DANGER: RISK OF EXPLOSION OR FIRE

WHAT CAN HAPPEN HOW TO PREVENT IT

• It is normal for electrical

contacts within the motor

and pressure switch

to spark.

• Always operate the

compressor in a well

ventilated area free of

combustible

materials, gasoline,

or solvent vapors.

• If electrical sparks from

compressor come into

contact with flammable

vapors, they may ignite,

causing fire or explosion.

• If spraying flammable

materials, locate compressor

at least 20 feet (6.1 m)

away from spray area. An

additional length of hose may

be required.

• Store flammable materials

in a secure location away

from compressor.

• Restricting any of the

compressor ventilation

openings will cause

serious overheating and

could cause fire.

• Never place objects against

or on top of compressor.

• Operate compressor in

an open area at least 12"

(30.5 cm) away from any

wall or obstruction that would

restrict the flow of fresh air to

the ventilation openings.

• Operate compressor in a

clean, dry well ventilated

area. Do not operate

unit indoors or in any

confined area.

• Unattended operation of

this product could result in

personal injury or property

damage. To reduce

the risk of fire, do not

allow the compressor to

operate unattended.

• Always remain in attendance

with the product when it

is operating.

• Always turn off and unplug

unit when not in use.

6

English

DANGER: RISK TO BREATHING (ASPHYXIATION)

WHAT CAN HAPPEN HOW TO PREVENT IT

• The compressed air

directly from your

compressor is not safe

for breathing. The air

stream may contain carbon

monoxide, toxic vapors,

or solid particles from the

air tank. Breathing these

contaminant's can cause

serious injury or death.

• Air obtained directly from the

compressor should never

be used to supply air for

human consumption. In order

to use air produced by this

compressor for breathing,

suitable filters and in-line

safety equipment must be

properly installed. In-line

filters and safety equipment

used in conjunction with the

compressor must be capable

of treating air to all applicable

local and federal codes prior

to human consumption.

• Sprayed materials such

as paint, paint solvents,

paint remover, insecticides,

weed killers, may

contain harmful vapors

and poisons.

• Work in an area with good

cross ventilation. Read and

follow the safety instructions

provided on the label or

safety data sheets for the

materials you are spraying.

Always use certified safety

equipment: OSHA/MSHA/

NIOSH respiratory protection

designed for use with your

specific application.

DANGER: RISK OF INJURY OR PROP ER TY DAMAGE WHEN

TRANSPORTING OR STORING

WHAT CAN HAPPEN HOW TO PREVENT IT

• Oil can leak or spill

and could result in fire

or breathing hazard;

serious injury or death

can result. Oil leaks will

damage carpet, paint or

other surfaces in vehicles

or trailers.

• Always place compressor

on a protective mat when

transporting to protect

against damage to vehicle

from leaks. Remove

compressor from vehicle

immediately upon arrival at

your destination. Always keep

compressor level and never

lie on its side.

WARNING: RISK OF BURSTING

Air Tank: The air tank on your Air Compressor is designed

and may be UM coded (for units with air tanks greater than 6

inch diameter) according to ASME Section VIII, Div. 1 rules. All

pressure vessels should be inspected once every two years. To

nd your state pressure vessels inspector, look under the Division

of Labor and Industries in the government section of a phone

book or call 1-800-4-

DeWALT

forassistance.

The following conditions could lead to a weakening of the air tank,

and result in a violent air tank explosion:

7

English

WHAT CAN HAPPEN HOW TO PREVENT IT

• Failure to properly drain

condensed water from

air tank, causing rust

and thinning of the steel

air tank.

• Drain air tank daily or after

each use. If air tank develops

a leak, replace it immediately

with a new air tank or replace

the entire compressor.

• Modifications or attempted

repairs to the air tank.

• Never drill into, weld, or make

any modifications to the

air tank or its attachments.

Never attempt to repair a

damaged or leaking air tank.

Replace with a new air tank.

• Unauthorized modifications

to the safety valve or any

other components which

control air tank pressure.

• The air tank is designed

to withstand specific

operating pressures.

Never make adjustments

or parts substitutions

to alter the factory set

operating pressures.

Attachments & accessories:

• Exceeding the pressure

rating of air tools, spray

guns, air operated

accessories, tires, and

other inflatables can cause

them to explode or fly

apart, and could result in

serious injury.

• Follow the equipment

manufacturers

recommendation and never

exceed the maximum

allowable pressure rating

of attachments. Never use

compressor to inflate small

low pressure objects such

as children’s toys, footballs,

basketballs, etc.

WARNING: RISK OF ELECTRICAL SHOCK

WHAT CAN HAPPEN HOW TO PREVENT IT

• Your air compressor is

powered by electricity.

Like any other electrically

powered device, If it is not

used properly it may cause

electricshock.

• Never operate the

compressor outdoors when it

is raining or in wetconditions.

• Never operate compressor

with protective covers

removed ordamaged.

• Repairs attempted by

unqualied personnel can

result in serious injury or

death byelectrocution.

• Any electrical wiring or

repairs required on this

product should be performed

by a

DeWALT

factory

service center or a

DeWALT

authorized service center in

accordance with national and

local electricalcodes.

• Electrical Grounding:

Failure to provide

adequate grounding to

this product could result

in serious injury or death

from electrocution. See

Grounding Instructions

underInstallation.

• Make certain that the

electrical circuit to which the

compressor is connected

provides proper electrical

grounding, correct voltage

and adequate fuseprotection.

8

English

WARNING: RISK FROM FLYING OBJECTS

WHAT CAN HAPPEN HOW TO PREVENT IT

• The compressed air

stream can cause soft

tissue damage to exposed

skin and can propel dirt,

chips, loose particles,

and small objects at high

speed, resulting in property

damage or personal injury.

• Always wear certified safety

equipment: ANSI Z87.1 eye

protection (CAN/CSA Z94.3)

with side shields when using

the compressor.

• Never point any nozzle or

sprayer toward any part of

the body or at other people

or animals.

• Always turn the compressor

off and bleed pressure

from the air hose and air

tank before attempting

maintenance, attaching tools

or accessories.

WARNING: RISK OF HOT SURFACES

WHAT CAN HAPPEN HOW TO PREVENT IT

• Touching exposed metal

such as the compressor

head, engine head, engine

exhaust or outlet tubes,

can result in serious burns.

• Never touch any exposed

metal parts on compressor

during or immediately after

operation. Compressor

will remain hot for several

minutes after operation.

• Do not reach around

protective shrouds or attempt

maintenance until unit has

been allowed to cool.

WARNING: RISK FROM MOVING PARTS

WHAT CAN HAPPEN HOW TO PREVENT IT

• Moving parts such as the

pulley, flywheel, and belt

can cause serious injury if

they come into contact with

you or your clothing.

• Never operate the compressor

with guards or covers which

are damaged or removed.

• Keep your hair, clothing, and

gloves away from moving

parts. Loose clothes, jewelry,

or long hair can be caught in

moving parts.

• Air vents may cover moving

parts and should be avoided

as well.

9

English

• Attempting to operate

compressor with damaged

or missing parts or

attempting to repair

compressor with protective

shrouds removed can

expose you to moving

parts and can result in

serious injury.

• Any repairs required on this

product should be performed

by a

DeWALT

factory

service center or a

DeWALT

authorized service center.

WARNING: RISK OF UNSAFE OPERATION

WHAT CAN HAPPEN HOW TO PREVENT IT

• Unsafe op er a tion of your

air compressor could lead

to se ri ous in ju ry or death to

you or others.

• Review and understand all

instructions and warnings in

this manual.

• Be come fa mil iar with the

op eration and con trols of the

air compressor.

• Keep operating area

clear of all persons, pets,

and obstacles.

• Keep chil dren away from the

air compressor at all times.

• Do not operate the product

when fatigued or under the

influence of alcohol or drugs.

Stay alert at all times.

• Never defeat the safety fea-

tures of this prod uct.

• Equip area of operation with

a fire extinguisher.

• Do not op er ate machine with

missing, broken, or un au tho-

rized parts.

WARNING: RISK OF FALLING

WHAT CAN HAPPEN HOW TO PREVENT IT

• A portable compressor

can fall from a table,

workbench, or roof causing

damage to the compressor

and could result in

serious injury or death to

the operator.

• Always operate compressor

in a stable secure position to

prevent accidental movement

of the unit. Never operate

compressor on a roof or

other elevated position. Use

additional air hose to reach

high locations.

CAUTION: RISK FROM NOISE

WHAT CAN HAPPEN HOW TO PREVENT IT

• Under some conditions and

duration of use, noise from

this product may contribute

to hearing loss.

• Always wear certied safety

equipment: ANSI S12.6

(S3.19) hearingprotection.

SAVE THESE INSTRUCTIONS

FOR FUTURE USE

10

English

FEATURES (Fig. 1)

ON/OFF SWITCH

Place this switch (A) in the ON position to

G

A

J

provide automatic power to the pressure

switch and OFF to remove power at the

end of each use.

PRESSURE SWITCH

The pressure switch (J) automatically

starts the motor when the air tank

pressure drops below the factory set cut-

in pressure. It stops the motor when the air tank pressure reaches

the factory set cut-out pressure.

PRESSURE RELEASE VALVE

The pressure release valve located on the side of the pressure

switch, is designed to automatically release compressed air from

the compressor head and the outlet tube when the air compressor

reaches cut-out pressure or is shut off. The pressure release valve

allows the motor to restart freely. When the motor stops running,

air will be heard escaping from this valve for a few seconds. No air

should be heard leaking when the motor is running or after the unit

reaches cut-out pressure.

SAFETY VALVE

If the pressure switch does not shut off the air compressor at its cut-

out pressure setting, the safety valve (G) will protect against high

pressure by popping out at its factory set pressure (slightly higher

than the pressure switch cut-out setting).

CHECK VALVE

When the air compressor is operating, the check

F

valve (F) is open, allowing compressed air to enter

the air tank. When the air compressor reaches cut-

out pressure, the check valve closes, allowing air

pressure to remain inside the air tank.

TANK PRESSURE GAUGE

The tank pressure gauge (B) indi-

D

C

E

B

cates the reserve air pressure in

the tank.

OUTLET PRESSURE GAUGE

The outlet pressure gauge (C)

indicates the air pressure available

at the outlet side of the regulator. This pressure is controlled by the

regulator and is always less than or equal to the tank pressure.

REGULATOR

The regulator (D) controls the air pressure shown on the outlet

pressure gauge. Turn regulator knob clockwise to increase pressure

and counterclockwise to decrease pressure.

UNIVERSAL QUICK CONNECT BODIES (IF EQUIPPED)

The universal quick connect body (E) accepts the three most

popular styles of quick connect plugs: Industrial, automotive, and

ARO. One hand push-to-connect operation makes connections

simple and easy. The two quick connect bodies allow the use of two

tools at the same time.

11

English

DRAIN VALVE

The drain valve (H) is located at the base

H

of the air tank and is used to drain

condensation at the end of each use. See

Draining Air Tank under Maintenance.

COOLING SYSTEM

This compressor contains an advanced design cooling system.

It is normal for this fan to blow air through the vent holes in large

amounts. The cooling system is working when air is expelled.

AIR COMPRESSOR PUMP

The pump compresses air into the air tank. Working air is not

available until the compressor has raised the air tank pressure

above that required at the air outlet.

MOTOR OVERLOAD PROTECTOR

This motor has a manual thermal overload

K

M

N

protector. If the motor overheats for any

reason, the overload protector will shut off

the motor. The motor must be allowed to

cool down before restarting. To restart:

1. Ensure the On/Off switch (A) is in the

OFFposition.

2. Allow the motor tocool.

3. Depress the reset button (M) on

themotor.

OIL DIPSTICK

The oil dipstick (K) indicates the amount of oil in the pump. Check

pump oil daily, see Compressor Pump Oil under Maintenance.

AIR INTAKE FILTER

The filter (N) is designed to clean air entering the pump. To ensure

the pump continually receives a clean, cool, and dry air supply

the filter must always be clean and the filter intake must be free

from obstructions.

INSTALLATION

Assembly

INSTALLING HOSES

WARNING: Risk of unsafe operation. Firmly grasp hose in hand

when installing or disconnecting to prevent hosewhip.

1. Ensure regulated pressure gauge reads 0 PSI (0 kPa).

2. Grasp the hose at the quick connect plug and push the plug

into the quick connect body (E). Coupler will snap intoplace.

3. Grasp the hose and pull to ensure coupler isseated.

DISCONNECTING HOSES

WARNING: Risk of unsafe operation. Firmly grasp hose in hand

when installing or disconnecting to prevent hosewhip.

1. Ensure regulated pressure gauge reads 0 PSI (0 kPa).

2. Pull coupler on quick connect body back to release quick

connect plug onhose.

Lubrication and Oil

CAUTION: The compressor was shipped with oil in the crankcase.

A shipping plug is used to prevent oil from leaking during

shipment. Do not attempt to operate this air compressor without

rst checking the oil level. Serious damage can result from even

limited operation unless lled with oil and broken in correctly.

Closely follow Initial Set-up underOperation.

12

English

CAUTION: Use

SAE 5W-40

full syntheticoil.

1. Place unit on a level surface.

K

2. Remove the shipping plug and install

thedipstick.

3. Remove the dipstick (K) and check the

oil level. Oil should not exceed top raised

line on dipstick. If oil is below lower mark

see Checking Oil under Compressor

Pump Oil under Maintenance. NOTE: See

Specifications for pump oilcapacity.

CAUTION: Risk of unsafe operation. Overlling with oil will cause

premature compressor failure. Do notoverll.

4. Replacedipstick.

Grounding Instructions

WARNING: Risk of electrical shock. In the event of a short circuit,

grounding reduces the risk of shock by providing an escape wire for

the electric current. This air compressor must be properlygrounded.

The portable air compressor is equipped with a cord having a

grounding wire with an appropriate grounding plug.

1. The cord set and plug (O) with this unit

P

O

Q

contains a grounding pin (P). This plug

MUST be used with a grounded

outlet(Q).

IMPORTANT: The outlet being used must

be installed and grounded in accordance

with all local codes and ordinances.

2. Ensure the outlet being used has the same conguration as the

grounded plug. DO NOT USE ANADAPTER.

3. Inspect the plug and cord before each use. Do not use if there

are signs ofdamage.

4. If these grounding instructions are not completely understood, or

if in doubt as to whether the compressor is properly grounded,

have the installation checked by a qualiedelectrician.

DANGER: Risk of electrical shock. IMPROPER GROUNDING

CAN RESULT IN ELECTRICALSHOCK.

• Do not modify the plug provided. If it does not fit the available

outlet, a correct outlet should be installed by a qualified electrician.

• Repairs to the cord set or plug MUST be made by a

qualified electrician.

Extension Cords

Using extension cords is not recommended. The use of extension

cords will cause voltage to drop resulting in power loss to the motor

and overheating.

Instead of using an extension cord, increase the working reach of

the air hose by attaching another length of hose to its end. Attach

additional lengths of hose as needed.

If an extension cord must be used, be sure it is:

• a 3-wire extension cord that has a 3-blade grounding plug, and a

3-slot receptacle that will accept the plug on the product

• in good condition

• no longer than 50 feet (15,2 m)

• 12 gauge (AWG) or larger. (Wire size increases as gauge

number decreases. 10 AWG and 8 AWG may also be used. DO

NOT USE 14 OR 16 AWG.)

Voltage and Circuit Protection

Refer to the Voltage and Minimum Branch Circuit Requirements

under Specifications.

13

English

CAUTION: Certain air compressors can be operated on a

15 amp circuit if the following conditions are met.

• Voltage supply to circuit must comply with the National

Electrical Code.

• Circuit is not used to supply any other electrical needs.

• Extension cords comply with specifications.

• Circuit is equipped with a 15 amp circuit breaker or 15 amp

time delay fuse. NOTE: If compressor is connected to a circuit

protected by fuses, use only time delay fuses. Time delay fuses

should be marked “D” in Canada and “T” in the US.

If any of the above conditions cannot be met, or if operation of the

compressor repeatedly causes interruption of the power, it may be

necessary to operate it from a 20 amp circuit. It is not necessary

to change the cordset.

Compatibility

Air tools and accessories that are run off the compressor must be

compatible with petroleum-based products. If you suspect that a

material is not compatible with petroleum products, an air line filter

for removal of moisture and oil vapor in compressed air is required.

NOTE: Always use an air line filter to remove moisture and oil vapor

when spraying paint.

Location

Place the air compressor in a clean, dry and well ventilated area

at least 12" (30.5 cm) away from the wall or other obstructions

that will interfere with the flow of air. Keep the compressor away

from areas that have dirt and/or volatile fumes in the atmosphere.

These impurities may clog the intake filter and valves, causing

inefficient operation.

The air compressor pump and shroud are designed to allow for

proper cooling. The ventilation openings on the compressor are

necessary to maintain proper operating temperature. Do not place

rags or other containers on or near these openings.

Place the air compressor on a flat surface resting on the rubber feet.

NOISE CONSIDERATIONS

Consult local officials for information regarding acceptable noise

levels in your area. To reduce excessive noise, use vibration mounts

or silencers, relocate the unit or construct total enclosures or baffle

walls. Contact a

DeWALT

service center or call 1-800-4-

DeWALT

for assistance.

ELECTRICAL

Refer to all safety instructions before using unit. Observe extension

cord safety instructions if necessary. Always move the On/Off

switch (A) to the OFF position before removing the plug from

the outlet.

TRANSPORTING

When transporting the compressor in a vehicle, trailer, etc., ensure

that the tank is drained and the unit is secured. Use care when

driving to avoid tipping the unit over in the vehicle. Damage can

occur to the compressor or surrounding items if the compressor

is tipped.

MOVING

When moving the compressor, grasp the handle and carry the

compressor as close to the body as possible.

WARNING: Risk of unsafe operation. Ensure proper footing and

use caution when carrying compressor to avoid a loss ofbalance.

14

English

PREPARATION FOR USE

Pre-Start Checklist (Fig. 1)

1. Ensure the On/Off switch (A) is in the OFFposition.

2. Plug the power cord into the correct branch circuit receptacle. See

Voltage and Circuit Protection underInstallation.

3. Ensure air tank is drained, see Draining Air Tank under

Maintenance.

4. Ensure the drain valve (H) is closed.

5. Ensure safety valve (G) is functioning properly, see Checking

Safety Valve under Maintenance.

6. Check pump oil level, see Compressor Pump Oil

under Maintenance.

CAUTION: Do not operate without oil or with inadequate oil.

DEWALT

is not responsible for compressor failure caused by inadequateoil.

7. Turn regulator knob (D) counterclockwise until fully closed. Ensure

regulated pressure gauge reads 0 PSI (0 kPa).

8. Attach hose andaccessories.

WARNING: Risk of unsafe operation. Firmly grasp hose in hand

when installing or disconnecting to prevent hosewhip.

9. Ensure all covers and labels are in place, legible (for labels) and

securely mounted. Do not use compressor until all items have

beenveried.

WARNING: Risk of bursting. Too much air pressure causes a

hazardous risk of bursting. Check the manufacturer’s maximum

pressure rating for air tools and accessories. The regulator outlet

pressure must never exceed the maximum pressurerating.

INITIAL SET-UP (FIG. 1)

WARNING: Do not operate this unit until you read and

understand this instruction manual for safety, operation and

maintenanceinstructions.

BREAK-IN PROCEDURE

WARNING:

Serious damage may result if the following break-in

instructions are not closelyfollowed.

This procedure is required before the air compressor is put into

service for the first time and when the check valve or a compressor

pump/motor has been replaced.

1. Ensure the On/Off switch (A) is in the OFFposition.

NOTE: If hose is not connected to Quick Connect body, pull

coupler back until it clicks to prevent air from escaping through the

quick connect.

2. Plug the power cord into the correct branch circuit receptacle.

See Voltage and Circuit Protection underInstallation.

3. Open the drain valve (counter-clockwise) fully to permit air to

escape and prevent air pressure build up in the air tank during

the break-inperiod.

4. Move the On/Off switch to the ON position. The compressor

willstart.

5. Run the compressor for 20minutes.

6. After 20 minutes, close the drain valve by turning clockwise. The

tank will ll to cut-out pressure and the motor will stop.

7. Compressed air will be available until it is used or bled off.

OPERATING PROCEDURES

Start-up (Fig. 1)

1. Follow Pre-Start Checklist under Preparation for Use.

2. Move the On/Off switch to the ON position and allow tank

pressure to build. Motor will stop when tank pressure reaches

cut-outpressure.

15

English

CAUTION: Risk of unsafe operation. Compressed air from the unit

may contain wa ter condensation and oil mist. Do not spray un l-

tered air at an item that could be damaged by moisture. Some air

op er ated tools or de vic es may require ltered air. Read the in struc-

tions for the air tool ordevice.

3. Adjust regulator (D) to desired setting. See Regulator

underFeatures.

Shut-down (Fig. 1)

1 Move On/Off switch (A) is in the OFF position. NOTE: If nished

using compressor, follow Steps 2 -6.

2. Turn regulator knob (D) counterclockwise until fully closed.

Ensure regulated pressure gauge reads 0 PSI (0 kPa).

3. Remove hose andaccessory.

4. Drain the air tank, see Draining Air Tank under Maintenance.

Ensure air tank pressure gauge reads 0 PSI (0 kPa).

WARNING: Risk of bursting. Drain air tank daily. Water will con-

dense in air tank. If not drained, water will corrode and weaken the

air tank causing a risk of air tankrupture.

5. Allow the compressor to cooldown.

6. Wipe air compressor clean and store in a safe, non-freezingarea.

MAINTENANCE

The following procedures must be followed when maintenance or

service is performed on the air compressor.

1. Ensure On/Off switch is in the OFFposition.

2. Remove air compressor plug fromoutlet.

3. Drain airtank.

4. Allow air compressor to cool down before startingservice.

NOTE: All compressed air systems contain maintenance parts

(e.g., oil, filters, separators) that are periodically replaced. These

used parts may contain substances that are regulated and must

be disposed of in accordance with local, state, and federal laws

and regulations.

NOTE: Take note of the positions and locations of parts during

disassembly to make reassembly easier.

NOTE: Any service operations not included in this section should

be performed by a

DeWALT

factory service center or a

DeWALT

authorized service center.

16

English

Maintenance Chart

Procedure

Daily Weekly Monthly 1 year or

200 Hours

Check safety valve

X

Inspect air filter +

X

Drain air tank

X

Check pump oil level

X

Change pump oil**+

X

Oil leak inspection

X

Check for unusual noise/

vibration

X

Check for air leaks*

X

Clean compressor

exterior

X

* To check for air leaks apply a solution of soapy water around

joints. While compressor is pumping to pressure and after pressure

cuts out, look for air bubbles to form.

** The pump oil must be changed after the first 20 hours of

operation. Thereafter, when using

SAe 5W-40 full synthetic

oil,

change oil every 200 hours of operation or once a year, whichever

comes first.

+ Perform more frequent in dusty or humid conditions

Checking Safety Valve (Fig. 1)

WARNING: Hot surfaces. Risk of burn. Aftercooler, pump head, and

surrounding parts are very hot, do not touch (see the Hot Surfaces

identied in Fig. 2). Allow compressor to cool prior to servicing.

WARNING: Risk of bursting. If the safety valve does not work

properly, over-pressurization may occur, causing air tank rupture or

anexplosion.

Before starting compressor, pull the ring on the safety valve to

make sure that the safety valve operates freely. If the valve is stuck

or does not operate smoothly, it must be replaced with the same

type of valve.

Checking Air Filter Element (Fig. 1)

WARNING: Hot surfaces. Risk of burn. Aftercooler, pump head, and

surrounding parts are very hot, do not touch (see the Hot Surfaces

identied in Fig. 2). Allow compressor to cool prior to servicing.

1. Ensure the On/Off switch (A) is in the OFFposition.

2. Allow unit tocool.

3. Remove air lter (N) fromunit.

4. Carefully pry lter top frombase.

5. Remove element from lterbase.

6. If element needs cleaning, blow out with air. Replace if needed.

Purchase replacement parts from your local dealer or authorized

service center. Always use identical replacementparts.

7. Place element back in lter base.

8. Snap lter top to lter base.

9. Reassemble air lter to unit. Ensure exhaust outlet pointsdown.

CAUTION: Risk of unsafe operation. Do not operate without air

inlet lter

17

English

Draining Air Tank (Fig. 1)

WARNING: Risk of unsafe operation. Risk from noise. Air

tanks contain high pressure air. Keep face and other body parts

away from outlet of drain. Use safety glasses [ANSI Z87.1 (CAN/

CSA Z94.3)] when draining as debris can be kicked up into face.

Use ear protection [ANSI S12.6 (S3.19)] as air ow noise is loud

whendraining.

NOTE: All compressed air systems generate condensate that

accumulates in any drain point (e.g. tanks, filter, aftercoolers,

dryers). This condensate contains lubricating oil and/or substances

which may be regulated and must be disposed of in accordance with

local, state, and federal laws and regulations.

1. Ensure On/Off switch is in the OFFposition.

2. Move compressor into an inclined position so drain valve (H) is

at the lowest point (this will assist in removing moisture, dirt, etc.

from air tanks)

3. Place a suitable container under the drain valve to catchdischarge.

4. Grasp knurled knob on drainvalve.

5. Slowly rotate knob to gradually bleed air from airtank.

WARNING: Risk of bursting. Drain air tank daily. Water will con-

dense in air tank. If not drained, water will corrode and weaken the

air tank causing a risk of air tankrupture.

CAUTION: Risk of property damage. Drain water from air tank may

contain oil and rust, which can cause stains.

6. When air tank pressure gauge reads 10 PSI (68,9 kPa), rotate

valve to the fully openposition.

7. Close drain valve whennished.

Compressor Pump Oil (Fig. 1)

CHECKING OIL

WARNING: Hot surfaces. Risk of burn. Aftercooler,

pump head, and surrounding parts are very hot,

do not touch (see the Hot Surfaces identied in

Fig. 2). Allow compressor to cool prior to servicing.

1. Ensure On/Off switch is in the OFFposition.

2. Place unit on a at levelsurface.

3. Remove dipstick (K) and wipeclean.

4. Reinsert dipstick fully into oil ll port for a few

seconds to allow oil to collect on thedipstick.

5. Remove oil dipstick to read oil level. Oil should not

exceed top raised line on dipstick. If oil is below

lower mark, add same type of oil in crankcase and

follow Steps 4 -6.

NOTE: When lling the crankcase, the oil ows

very slowly into the pump. If the oil is added too

quickly, it will overow and appear to befull.

CAUTION: Risk of unsafe operation. Overlling with

oil will cause premature compressor failure. Do notoverll.

6. Replacedipstick.

CHANGING OIL

NOTE: Pump oil contains substances that are regulated and must

be disposed of in accordance with local, state and federal laws

and regulations.

WARNING: Hot surfaces. Risk of burn. Aftercooler, pump head, and

surrounding parts are very hot, do not touch (see the Hot Surfaces

identied in Fig. 2). Allow compressor to cool prior to servicing.

MAX

MIN

L

K

18

English

1. Ensure On/Off switch is in the OFFposition.

2. Allow the unit tocool.

3. Remove air compressor plug fromoutlet.

4. Drain airtank.

5. Locate a suitable container under pump drain plug (L).

6. Remove the dipstick (K) fromcrank case.

7. Remove the oil drain plug (L).

8. Allow ample time for all oil to drain out. (Tilting the compressor

towards the drain plug will assist in draining.)

9. Install the oil drainplug.

10. Fill pump using SAE 5W-40 full syntheticoil.

11. Replacedipstick.

Accessories

Recommended accessories for use with your tool are available

for purchase from your local dealer or authorized service center. If

you need assistance in locating any accessory for your tool, please

contact

DeWALT

Industrial Tool Co., 701 East Joppa Road, Towson,

MD 21286, call 1-800-4-

DeWALT

(1-800-433-9258) or visit our

website www.

DeWALT

.com.

CAUTION: The use of any other accessory not recommended for

use with this tool could be hazardous. Use only accessories rated

equal to or higher than the rating of the aircompressor.

SERVICE INFORMATION

Please have the following information available for all service calls:

Model Number ____________ Serial Number _________________

Date and Place of Purchase ______________________________

Repairs

To assure product SAFETY and RELIABILITY, repairs, maintenance

and adjustment should be performed by a

DeWALT

factory service

center, a

DeWALT

authorized service center or other qualified

service personnel. Always use identical replacement parts.

Full One Year Warranty

DeWALT

heavy duty industrial tools are warranted for one year from

date of purchase. We will repair, without charge, any defects due

to faulty materials or workmanship. For warranty repair information,

call 1-800-4-

DeWALT

. This warranty does not apply to accessories

or damage caused where repairs have been made or attempted by

others. This warranty gives you specific legal rights and you may

have other rights which vary in certain states or provinces.

LATIN AMERICA: This warranty does not apply to products sold

in Latin America. For products sold in Latin America, see country

specific warranty information contained either in the packaging, call

the local company or see website for warranty information.

FREE WARNING LABEL REPLACEMENT: If your warning

labels become illegible or are missing, call 1-800-4-

DeWALT

for a

free replacement.

19

English

Glossary

CFM: Cubic feet perminute.

SCFM: Standard cubic feet per minute; a unit of measure of air delivery.

PSI: Pounds per square inch; a unit of measure ofpressure.

kPa (kilopascal): Metric pressure measurement. 1 kilopascal equal 1000 pascals.

Code Certification: Products that bear one or more of the following marks: UL, CUL, ETL, CETL, have been evaluated by OSHA certied

independent safety laboratories and meet the applicable Underwriters Laboratories Standards forSafety.

Cut-In Pressure: While the motor is off, air tank pressure drops when accessory is used. When the tank pressure drops to a certain low level

the motor will restart automatically. The low pressure at which the motor automatically restarts is called cut-in pressure.

Cut-Out Pressure: When an air compressor is turned on and begins to run, air pressure in the air tank begins to build. It builds to a certain

high pressure before the motor automatically shuts off, protecting your air tank from pressure higher than its capacity. The high pressure

at which the motor shuts off is called cut-out pressure.

Branch Circuit: The circuit carrying electricity from electrical panel tooutlet.

Duty Cycle: For proper operation of your air compressor, it is recommended that a 50% duty cycle be maintained; that is, the air compressor

should not run more than 5 minutes in any 10 minuteperiod.

20

English

Troubleshooting Guide

This section provides a list of the more frequently encountered malfunctions, their causes and corrective actions. The operator or

maintenance personnel can perform some corrective actions, and others may require the assistance of a qualified

DeWALT

technician or

your dealer.

Problem Code

Excessive air tank pressure-safety valve pops off .................................................................... 1,2

Air leaks ..................................................................................................................................... 3

Air leaks in air tank or at air tank welds ..................................................................................... 4

Air leaks between head and valve plate .................................................................................... 5

Air leaks from safety valve .......................................................................................................... 6

Knocking Noise ........................................................................................................................... 6,16,17

Pressure reading on the regulated pressure gauge drops when an accessory is used ........... 7

Compressor is not supplying enough air to operate accessories .............................................. 8,9,10,11,12,15

Regulator knob has continuous air leak ..................................................................................... 13

Regulator will not shut off air outlet ............................................................................................ 13

Moisture in pump crankcase ....................................................................................................... 14,18

Motor will not run ........................................................................................................................ 11,19,20,21,22,23,24,25,26

Troubleshooting Codes

CODE POSSIBLE CAUSE POSSIBLE SOLUTION

1 Pressure switch does not shut off motor when compressor

reaches cut-out pressure

Set the On/Off switch to OFF, if the unit does not shut off

contact a

DeWALT

factory service center or a

DeWALT

authorized servicecenter.

2 Pressure switch cut-out too high

Contact a

DeWALT

factory service center or a

DeWALT

authorized servicecenter.

3

Tube fittings are not tight enough

Tighten ttings where air can be heard escaping. Check

ttings with soapy water solution. Do NotOvertighten.

La page charge ...

DeWalt Emglo D55153 Manuel utilisateur

Ce manuel convient également à

DeWalt Emglo D55153 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents