DeWalt D55154 Manuel utilisateur

Marque: DeWalt

Modèle: D55154

Catégorie: Compresseurs d'air

Taper: Manuel utilisateur

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-DeWALT

Instruction Manual

Guide D’utilisation

Manual de instrucciones

D55154

Heavy-Duty Electric Wheeled Dolly-Style Air Compressor

Compresseur d’air électrique, industriel sur chariot

Compresor de aire eléctrico con ruedas para trabajo pesado

final page size: 8.5 x 5.5 in

ENGLISH

English (original instructions) 1

Français (traduction de la notice d’instructions originale) 14

Español (traducido de las instrucciones originales) 29

ENGLISH

English (original instructions)

Definitions: Safety Alert Symbols and Words

This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risk

of personal injury or property damage.



DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or seriousinjury.



WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or seriousinjury.



CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderateinjury.



(Used without word) Indicates a safety related message.

NOTICE: Indicates a practice not related to personal injury which, if not avoided, may result in propertydamage.



WARNING! Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

seriousinjury.

WARNING: To reduce the risk of injury, read the

instructionmanual.



WARNING: This product contains chemicals known

to the State of California to cause cancer, and birth

defects or other reproductive harm. Wash hands

afterhandling.



WARNING: Some dust contains chemicals known to

the State of California to cause cancer, birth defects or

other reproductive harm such as asbestos and lead in

lead based paint.

On/off switch

Air tank pressure gauge

Regulated pressure

gauge

Pressure regulator

Quick connects

Check valve

Safety valve

Air tank drain valve

Power cord wrap

Pressure switch

Pump oil dipstick

Pump oil drain plug

Air intake filter (not

shown)

Handle

Handle locking knobs

Top panel for cargo

Fig. A

342

NOT A

STEP

1614

ENGLISH

SAVE ALL WARNINGS AND

INSTRUCTIONS FOR FUTURE

REFERENCE



DANGER: RISK OF EXPLOSION OR FIRE

What can happen How to prevent it

It is normal for electrical contacts

within the motor and pressure

switch to spark.

Always operate the compressor

in a well ventilated area free of

combustible materials, gasoline, or

solvent vapors.

If electrical sparks from compressor

come into contact with flammable

vapors, they may ignite, causing

fire or explosion.

If spraying flammable materials,

locate compressor at least 20 feet

(6.1 m) away from spray area.

An additional length of hose may

be required.

Store flammable materials

in a secure location away

from compressor.

Restricting any of the compressor

ventilation openings will cause

serious overheating and could

cause fire.

Never place objects against or on

top of compressor pump.

Operate compressor in an open

area at least 12" (30.5 cm) away

from any wall or obstruction that

would restrict the flow of fresh air

to the ventilation openings.

Operate compressor in a clean,

dry well ventilated area. Do not

operate unit indoors or in any

confined area.

Unattended operation of this

product could result in personal

injury or property damage.

To reduce the risk of fire, do

not allow the compressor to

operate unattended.

Always remain in attendance with

the product when it is operating.

Always turn off and unplug unit

when not in use.



CAUTION: RISK FROM NOISE

What can happen How to prevent it

Under some conditions and

duration of use, noise from

this product may contribute to

hearing loss.

Always wear certified safety

equipment: ANSI S12.6 (S3.19)

hearing protection.



DANGER: RISK TO BREATHING

(Asphyxiation)

What can happen How to prevent it

The compressed air directly from

your compressor is not safe for

breathing. The air stream may

contain carbon monoxide, toxic

vapors, or solid particles from

the air tank. Breathing these

contaminant's can cause serious

injury or death.

Air obtained directly from the

compressor should never be

used to supply air for human

consumption. In order to use air

produced by this compressor for

breathing, suitable filters and

in-line safety equipment must be

properly installed. In-line filters

and safety equipment used in

conjunction with the compressor

must be capable of treating air

to all applicable local and federal

codes prior to human consumption.

Sprayed materials such as paint,

paint solvents, paint remover,

insecticides, weed killers,

may contain harmful vapors

and poisons.

Work in an area with good cross

ventilation. Read and follow the

safety instructions provided on the

label or safety data sheets for the

materials you are spraying. Always

use certified safety equipment:

OSHA/MSHA/NIOSH respiratory

protection designed for use with

your specific application.



DANGER: RISK OF INJURY OR PROPERTY

DAMAGE WHEN TRANSPORTING

OR STORING

What can happen How to prevent it

Oil can leak or spill and could result

in fire or breathing hazard; serious

injury or death can result. Oil leaks

will damage carpet, paint or other

surfaces in vehicles or trailers.

Always place compressor

on a protective mat when

transporting to protect against

damage to vehicle from leaks.

Remove compressor from vehicle

immediately upon arrival at

your destination. Always keep

compressor level and never lie

on its side.



WARNING: RISK OF BURSTING

Air Tank: The air tank on your Air Compressor is designed

and may be UM coded (for units with air tanks greater

than 6 inch / 152 mm diameter) according to ASME

Section VIII, Div. 1 rules. All pressure vessels should

be inspected once every two years. To find your state

pressure vessels inspector, look under the Division of

Labor and Industries in the government section of a

phone book or call 1–800–4-

DeWALT forassistance.

The following conditions could lead to a weakening of the

air tank, and result in a violent air tank explosion:

What can happen How to prevent it

Failure to properly drain condensed

water from air tank, causing rust

and thinning of the steel air tank.

Drain air tank daily or after each

use. If air tank develops a leak,

replace it immediately with

a new air tank or replace the

entire compressor.

ENGLISH

Modifications or attempted repairs

to the air tank.

Never drill into, weld, or make

any modifications to the air tank

or its attachments. Never attempt

to repair a damaged or leaking air

tank. Replace with a new air tank.

Unauthorized modifications to

the safety valve or any other

components which control air

tank pressure.

The air tank is designed to

withstand specific operating

pressures. Never make adjustments

or parts substitutions to alter the

factory set operating pressures.

Attachments & accessories:

Exceeding the pressure rating of

air tools, spray guns, air operated

accessories, tires, and other

inflatables can cause them to

explode or fly apart, and could

result in serious injury.

Follow the equipment

manufacturers recommendation

and never exceed the maximum

allowable pressure rating of

attachments. Never use compressor

to inflate small low pressure

objects such as children’s toys,

footballs, basketballs, etc.

Tires:

Over inflation of tires could

result in serious injury and

property damage.

Use a tire pressure gauge to check

the tires pressure before each

use and while inflating tires; see

the tire sidewall for the correct

tire pressure.

NOTE: Air tanks, compressors

and similar equipment used to

inflate tires can fill small tires

similar to these very rapidly. Adjust

pressure regulator on air supply

to no more than the rating of the

tire pressure. Add air in small

increments and frequently use the

tire gauge to prevent over inflation.



WARNING: RISK OF ELECTRICAL SHOCK

What can happen How to prevent it

Your air compressor is powered

by electricity. Like any other

electrically powered device, If it

is not used properly it may cause

electric shock.

Never operate the compressor

outdoors when it is raining or in

wet conditions.

Never operate compressor with

protective covers removed

or damaged.

Repairs attempted by unqualified

personnel can result in serious

injury or death by electrocution.

Any electrical wiring or repairs

required on this product should

be performed by a D

eWALT

factory service center or a DeWALT

authorized service center in

accordance with national and local

electrical codes.

Electrical Grounding:

Failure to provide adequate

grounding to this product

could result in serious injury or

death from electrocution. See

Grounding Instructions

under Installation.

Make certain that the electrical

circuit to which the compressor

is connected provides proper

electrical grounding, correct

voltage and adequate

fuse protection.



WARNING: RISK FROM FLYING OBJECTS

What can happen How to prevent it

The compressed air stream can

cause soft tissue damage to

exposed skin and can propel

dirt, chips, loose particles, and

small objects at high speed,

resulting in property damage or

personal injury.

Always wear certified safety

equipment: ANSI Z87.1 eye

protection (CAN/CSA Z94.3)

with side shields when using

the compressor.

Never point any nozzle or sprayer

toward any part of the body or at

other people or animals.

Always turn the compressor off and

bleed pressure from the air hose

and air tank before attempting

maintenance, attaching tools

or accessories.



WARNING: RISK OF HOT SURFACES

What can happen How to prevent it

Touching exposed metal such as

the compressor head, engine head,

engine exhaust or outlet tubes, can

result in serious burns.

Never touch any exposed metal

parts on compressor during or

immediately after operation.

Compressor will remain hot for

several minutes after operation.

Do not reach around protective

shrouds or attempt maintenance

until unit has been allowed to cool.



WARNING: RISK OF INJURY FROM LIFTING

What can happen How to prevent it

Serious injury can result from

attempting to lift too heavy

an object.

The compressor is too heavy

to be lifted by one person.

Obtain assistance from others

before lifting.



WARNING: RISK FROM MOVING PARTS

What can happen How to prevent it

Moving parts such as the pulley,

flywheel, and belt can cause

serious injury if they come into

contact with you or your clothing.

Never operate the compressor

with guards or covers which are

damaged or removed

Keep your hair, clothing, and

gloves away from moving parts.

Loose clothes, jewelry, or long hair

can be caught in moving parts.

Air vents may cover moving parts

and should be avoided as well.

ENGLISH

Attempting to operate compressor

with damaged or missing parts or

attempting to repair compressor

with protective shrouds removed

can expose you to moving parts

and can result in serious injury.

Any repairs required on this

product should be performed by a

DeWALT factory service center or a

eWALT authorized service center.



WARNING: RISK OF UNSAFE OPERATION

What can happen How to prevent it

Unsafe op er a tion of your air

compressor could lead to se ri ous

in ju ry or death to you or others.

Review and understand all

instructions and warnings in

this manual.

Be come fa mil iar with the op eration

and con trols of the air compressor.

Keep operating area clear of all

persons, pets, and obstacles.

Keep chil dren away from the air

compressor at all times.

Do not operate the product when

fatigued or under the influence

of alcohol or drugs. Stay alert at

all times.

Never defeat the safety fea tures of

this prod uct.

Equip area of operation with a

fire extinguisher.

Do not op er ate machine

with missing, broken, or

un authorized parts.

Never stand on the compressor.



WARNING: RISK OF FALLING

What can happen How to prevent it

A portable compressor can fall

from a table, workbench, or roof

causing damage to the compressor

and could result in serious injury or

death to the operator.

Always operate compressor in a

stable secure position to prevent

accidental movement of the unit.

Never operate compressor on a

roof or other elevated position.

Use additional air hose to reach

high locations.

SAVE THESE INSTRUCTIONS FOR

FUTURE USE



WARNING: Some dust created by power sanding,

sawing, grinding, drilling, and other construction

activities contains chemicals known to the State

of California to cause cancer, birth defects or

other reproductive harm. Some examples of these

chemicalsare:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other

masonry products, and

• arsenic and chromium from chemically-

treatedlumber.

Your risk from these exposures varies, depending on how

often you do this type of work. To reduce your exposure to

these chemicals: work in a well ventilated area, and work with

approved safety equipment, such as those dust masks that are

specially designed to filter out microscopicparticles.

• Avoid prolonged contact with dust from power

sanding, sawing, grinding, drilling, and other

construction activities. Wear protective clothing and

wash exposed areas with soap and water. Allowing

dust to get into your mouth, eyes, or lay on the skin may

promote absorption of harmfulchemicals.



WARNING: Use of this tool can generate and/

or disperse dust, which may cause serious and

permanent respiratory or other injury. Always use

NIOSH/OSHA approved respiratory protection

appropriate for the dust exposure. Direct particles

away from face andbody.

COMPONENTS (FIG. A–G)



WARNING: Never modify the power tool or any part

of it. Damage or personal injury couldresult.

Refer to Figure A at the beginning of this manual for a

complete list ofcomponents.

Specifications

Model D55154

Weight 82 lbs (37.3kg)

Height 20.0" (508.0 mm)

Width 18.5" (469.9 mm)

Length 23.0" (584.2 mm)

Air Tank Capacity (Gallons) 4.0 (15.1 liters)

Approx Cut-In Pressure 95 PSI (655 kPa)

Approx. Cut-Out Pressure 125 PSI (861.8 kPa)

SCFM @ 100 PSI (689.5 Kpa) 3.8

Motor 1.1 HP (continuous)

Volts/Amps/Hertz 120V/14 A/60 Hz.

RPM 3450

Minumum Branch Circuit Requirement 15 Amp

Pump Oil Capacity 12 oz. (354.9 ml)

Duty Cycle 5 Minutes On /

5 Minutes Off

ENGLISH

OUTLET TUBE

CHECK VALVE

PUMP CYLNDER

AND HEAD

Fig. B

On/Off Switch

Place this switch

1

in the ON position to provide automatic

power to the pressure switch and OFF to remove power at

the end of eachuse.

Pressure Switch

The pressure switch

10

automatically starts the motor

when the air tank pressure drops below the factory set cut-

in pressure. It stops the motor when the air tank pressure

reaches the factory set cut-outpressure.

Fig. C

Safety Valve

If the pressure switch does not shut off the air compressor

at its cut-out pressure setting, the safety valve

7

will

protect against high pressure by popping out at its factory

set pressure (slightly higher than the pressure switch cut-

outsetting).

Fig. D

Check Valve

When the air compressor is operating, the check valve

6

open, allowing compressed air to enter the air tank. When

the air compressor reaches cut-out pressure, the check valve

closes, allowing air pressure to remain inside the airtank.

Fig. E

Tank Pressure Gauge

The tank pressure gauge

2

indicates the reserve air

pressure in thetank.

Regulated Pressure Gauge

The regulated pressure gauge

3

indicates the air pressure

available at the outlet side of the regulator. This pressure is

controlled by the regulator and is always less than or equal

to the tankpressure.

Regulator

The regulator

4

controls the air pressure shown on

the regulated pressure gauge. Turn regulator knob

clockwise to increase pressure and counterclockwise to

decreasepressure.

Universal Quick Connect Bodies

The universal quick connect body

5

accepts the three

most popular styles of quick connect plugs: Industrial,

automotive, and ARO. One hand push-to-connect operation

makes connections simple and easy. The two quick connect

bodies allow the use of two tools at the sametime.

Drain Valve

The drain valve

8

is located at the base of the air tank and

is used to drain condensation at the end of each use. See

Draining Air Tank underMaintenance.

Fig. F

Cooling System

This compressor contains an advanced design cooling

system. It is normal for this fan to blow air through the vent

holes in large amounts. The cooling system is working when

air isexpelled.

Air Compressor Pump

The pump compresses air into the air tank. Working air is

not available until the compressor has raised the air tank

pressure above that required at the airoutlet.

Motor Overload Protector (not shown)

The motor has a thermal overload protector. If the motor overheats

for any reason, the overload protector will shut off the motor. The

motor must be allowed to cool down before restarting.

To restart:

1. Ensure the On/Off switch

1

is in the OFFposition and

unplug unit.

2. Allow the motor to cool.

3. Plug the power cord into an appropriate electrical outlet

4. Set the Auto/Off switch to the “ON” position.

ENGLISH

Oil Dipstick

The oil dipstick

11

indicates the amount of oil in the

pump. Check pump oil daily, see Compressor Pump Oil

underMaintenance.

Fig. G

Air Intake Filter

The filter

14

is designed to clean air entering the pump.

To ensure the pump continually receives a clean, cool, and

dry air supply the filter must always be clean and the filter

intake must be free fromobstructions.

ASSEMBLY AND ADJUSTMENTS



WARNING: To reduce the risk of serious personal

injury, turn unit off and disconnect it from

power source before making any adjustments or

removing/installing attachments or accessories.

An accidental start-up can causeinjury.

Assembly (Fig. A, H–M)

Installing Handle



CAUTION: Risk of personal injury. Avoid placing

hands between handle and top panel when

assembling to preventpinching.

1. Place handle

14

into bushings on top panel

17

2. Depress snap buttons and slide handle through first

bushings until it stops at secondbushings.

3. Reach under top panel and depress snap buttons again

and slide through secondbushings.

4. Pull handle all the way up until it stops. Turn knobs

15

to lock handle in place. IMPORTANT: Always pull

handle up and lock in place before using as adolly.

5. If not using the dolly feature, loosen knobs and push

handle down until itstops.

Installing Hoses



WARNING: Risk of unsafe operation. Firmly grasp

hose in hand when installing or disconnecting to

prevent hosewhip.

1. Ensure regulated pressure gauge reads 0 PSI (0kPa).

2. Grasp the hose at the quick connect plug and push the

plug into the quick connect body

5

. Coupler will snap

intoplace.

3. Grasp the hose and pull to ensure coupler isseated.

Fig. H

Disconnecting Hoses



WARNING: Risk of unsafe operation. Firmly grasp

hose in hand when installing or disconnecting to

prevent hosewhip.

1. Ensure regulated pressure gauge reads 0 PSI (0kPa).

2. Pull coupler on quick connect body back to release

quick connect plug onhose.

Lubrication and Oil



CAUTION: The compressor was shipped with oil in

the crankcase. A shipping plug is used to prevent oil

from leaking during shipment. Do not attempt to

operate this air compressor without first checking the

oil level. Serious damage can result from even limited

operation unless filled with oil and broken in correctly.

Closely follow Initial Set-up underOperation.



CAUTION: Use SAE 5W-40 full synthetic oil.

1. Place unit on a levelsurface.

2. Remove the shipping plug and install the dipstick

11

3. Remove the dipstick and check the oil level. Oil should

not exceed top raised line on dipstick. If oil is below

lower mark see Checking Oil under Compressor

Pump Oil underMaintenance.

NOTE: See Specifications for pump oilcapacity.



CAUTION: Risk of unsafe operation. Overfilling with

oil will cause premature compressor failure. Do

notoverfill.

Fig. I

Grounding Instructions



WARNING: Risk of electrical shock. In the event

of a short circuit, grounding reduces the risk

of shock by providing an escape wire for the

electric current. This air compressor must be

properlygrounded.

The portable air compressor is equipped with a cord having

a grounding wire with an appropriate groundingplug.

1. The cord set and plug

17

with this unit contains a

grounding pin

18

. This plug MUST be used with a

grounded outlet

19

ENGLISH

Fig. J

IMPORTANT: The outlet being used must be installed and

grounded in accordance with all local codes andordinances.

2. Ensure the outlet being used has the same

configuration as the grounded plug. DO NOT USE

ANADAPTER.

3. Inspect the plug and cord before each use. Do not use if

there are signs ofdamage.

4. If these grounding instructions are not completely

understood, or if in doubt as to whether the compressor

is properly grounded, have the installation checked by a

qualifiedelectrician.



DANGER: Risk of electrical shock. IMPROPER

GROUNDING CAN RESULT IN ELECTRICALSHOCK.

• Do not modify the plug provided. If it does not

fit the available outlet, a correct outlet should be

installed by a qualifiedelectrician.

• Repairs to the cord set or plug MUST be made by a

qualifiedelectrician.

Extension Cords

Using extension cords is not recommended. The use of

extension cords will cause voltage to drop resulting in

power loss to the motor andoverheating.

Instead of using an extension cord, increase the working

reach of the air hose by attaching another length of hose to

its end. Attach additional lengths of hose asneeded.

If an extension cord must be used, be sure it is:

• a 3-wire extension cord that has a 3-blade grounding

plug, and a 3-slot receptacle that will accept the plug

on the product

• in good condition

• plug is not worn

• no longer than 50 feet (15,2 m)

• 12 gauge (AWG) or larger. (Wire size increases as gauge

number decreases. 10 AWG may also be used. DO NOT

USE 14, 16 OR 18 AWG.)

Voltage and Circuit Protection

Refer to the Voltage and Minimum Branch Circuit

Requirements underSpecifications.



CAUTION: Certain air compressors can be operated

on a 15 amp circuit if the following conditions

aremet.

• Voltage supply to circuit must comply with the

National ElectricalCode.

• Circuit is not used to supply any other

electricalneeds.

• Extension cords comply withspecifications.

• Circuit is equipped with a 15 amp circuit breaker

or 15 amp time delay fuse. NOTE: If compressor

is connected to a circuit protected by fuses, use

only time delay fuses. Time delay fuses should be

marked “D” in Canada and “T” in theUS.

If any of the above conditions cannot be met, or

if operation of the compressor repeatedly causes

interruption of the power, it may be necessary to

operate it from a 20 amp circuit. It is not necessary to

change the cordset.

Compatibility

Air tools and accessories that are run off the compressor

must be compatible with petroleum-based products. If you

suspect that a material is not compatible with petroleum

products, an air line filter for removal of moisture and oil

vapor in compressed air isrequired.

NOTE: Always use an air line filter to remove moisture and

oil vapor when sprayingpaint.

Location

Place the air compressor in a clean, dry and well ventilated

area at least 12" (30.5 cm) away from the wall or other

obstructions that will interfere with the flow of air. Keep the

compressor away from areas that have dirt and/or volatile

fumes in the atmosphere. These impurities may clog the

intake filter and valves, causing inefficientoperation.

The air compressor pump and shroud are designed to

allow for proper cooling. The ventilation openings on the

compressor are necessary to maintain proper operating

temperature. Do not place rags or other containers on or

near theseopenings.

Place the air compressor on a flat surface resting on the

rubberfeet.

Noise Considerations

Consult local officials for information regarding acceptable

noise levels in your area. To reduce excessive noise, use

vibration mounts or silencers, relocate the unit or construct

total enclosures or baffle walls. Contact a DeWALT service

center or call 1–800–4-

DeWALT forassistance.

Electrical

Refer to all safety instructions before using unit. Observe

extension cord safety instructions if necessary. Always move

the On/Off switch

1

to the OFF position before removing

the plug from theoutlet.

Transporting

When transporting the compressor in a vehicle, trailer, etc.

ensure that the air tank is drained and the unit is secured

and placed on a flat horizontalsurface.

NOTE: Use recommended tie down points

20

when

transporting. Use care when driving so to avoid tipping the

unit over in the vehicle. Damage can occur to the unit or

surrounding items if unit istipped.

Lifting

Always use two people when lifting and lift from the

recommended lift points

21

ENGLISH

Fig. K

Moving

1. Grasp handle

14

of compressor and pull up until it

stops. Turn knobs to lock handle inplace.

2. Grasp handle and tilt compressor so unit can be rolled

on thetires.



WARNING: Risk of unsafe operation. Ensure proper

footing and use caution when rolling compressor so

that unit does not tip or cause loss ofbalance.

3. When location is reached slowly lower compressor

to ground. Always store compressor in a

horizontalposition.

NOTE: Should the unit tip over, hard starting and smoking

will occur due to oilspillage.

Dolly Feature

1. Grasp handle

14

of compressor and pull up

until it stops. Turn knobs to lock handle in place.

IMPORTANT:Always pull handle up and lock in place

before using as adolly.

Fig. L

2. Place cargo onto top panel ofcompressor.

3. Secure cargo to top panel with retention straps. Hook

cargo retention straps into positioning holes in top

panel. NOTE: Retention straps to secure cargo may be

purchase from a local hardware store or home center in

a variety ofsizes.

Fig. M



CAUTION: Risk of unsafe operation. Do not transport

unsecuredcargo.



CAUTION: Risk of unsafe operation. Load limit is

100lbs. (45.4kg) do notexceed.

4. With cargo secured, grasp handle and tilt compressor so

unit can be rolled on thetires.



WARNING: Risk of unsafe operation. Ensure proper

footing and use caution when rolling compressor so

that unit does not tip or cause loss ofbalance.

5. When location is reached slowly lower compressor

to ground. Always store compressor in a

horizontalposition.

OPERATION



WARNING: To reduce the risk of serious personal

injury, turn unit off and disconnect it from

power source before making any adjustments or

removing/installing attachments or accessories.

An accidental start-up can causeinjury.

Preparation For Use

Pre-Start Checklist (Fig. A)

1. Ensure the On/Off switch

1

is in the OFFposition.

2. Plug the power cord into the correct branch circuit

receptacle. See Voltage and Circuit Protection

underAssembly and Adjustments.

3. Ensure air tank is drained, see Draining Air Tank

underMaintenance.

4. Ensure the drain valve

8

isclosed.

5. Ensure safety valve

7

is functioning properly, see

Checking Safety Valve underMaintenance.

6. Check pump oil level, see Compressor Pump Oil

underMaintenance.



CAUTION: Do not operate without oil or with

inadequate oil. DeWALT is not responsible for

compressor failure caused by inadequateoil.

7. Turn regulator knob

4

counterclockwise until fully

closed. Ensure regulated pressure gauge reads 0 PSI

(0kPa).

8. Attach hose andaccessories.



WARNING: Risk of unsafe operation. Firmly grasp

hose in hand when installing or disconnecting to

prevent hosewhip.

9. Ensure all covers and labels are in place, legible (for

labels) and securely mounted. Do not use compressor

until all items have beenverified.



WARNING: Risk of bursting. Too much air pressure

causes a hazardous risk of bursting. Check the

manufacturer’s maximum pressure rating for air tools

and accessories. The regulator outlet pressure must

never exceed the maximum pressurerating.

Initial Set-up

(Fig. A)



WARNING: Do not operate this unit until you read

and understand this instruction manual for safety,

operation and maintenanceinstructions.

ENGLISH

Break-in Procedure



CAUTION: RISK OF PROPERTY DAMAGE. Serious

damage may result if the following break-in

instructions are not closelyfollowed.

This procedure is required before the air compressor is put

into service for the first time and when the check valve or a

compressor pump/motor has beenreplaced.

1. Ensure the On/Off switch

1

is in the OFFposition.

NOTE: If hose is not connected to Quick Connect body,

pull coupler back until it clicks to prevent air from escaping

through the quickconnect.

2. Plug the power cord into the correct branch circuit

receptacle. See Voltage and Circuit Protection under

Assembly and Adjustments.

3. Open the drain valve (counter-clockwise) fully to permit

air to escape and prevent air pressure build up in the air

tank during the break-inperiod.

4. Move the On/Off switch to the ON position. The

compressor willstart.

5. Run the compressor for 120minutes.

6. After 120 minutes, close the drain valve by turning

clockwise. The tank will fill to cut-out pressure and the

motor willstop.

7. Compressed air will be available until it is used or

bledoff.

Operating Procedures

Start-up (Fig. A)

1. Follow Pre-Start Checklist under Preparation forUse.

2. Move the On/Off switch

to the ON position and

allow tank pressure to build. Motor will stop when tank

pressure reaches cut-outpressure.



CAUTION: Risk of unsafe operation. Compressed air

from the unit may contain wa ter condensation and oil

mist. Do not spray un fil tered air at an item that could

be damaged by moisture. Some air op er ated tools or

de vic es may require filtered air. Read the in struc tions

for the air tool ordevice.

3. Adjust regulator

4

to desired setting. See Regulator

underComponents.

Shut-down (Fig. A)

1. Move On/Off switch

1

is in the OFF position. NOTE: If

finished using compressor, follow Steps 2 -6.

2. Turn regulator knob

4

counterclockwise until fully

closed. Ensure regulated pressure gauge reads 0 PSI

(0kPa).

3. Remove hose andaccessory.

4. Drain the air tank, see Draining Air Tank under

Maintenance. Ensure air tank pressure gauge reads

0PSI (0kPa).



WARNING: Risk of bursting. Drain air tank daily.

Water will condense in air tank. If not drained, water

will corrode and weaken the air tank causing a risk of

air tankrupture.

5. Allow the compressor to cooldown.

6. Wipe air compressor clean and store in a safe, non-

freezingarea.

MAINTENANCE



WARNING: To reduce the risk of serious personal

injury, turn unit off and disconnect it from

power source before making any adjustments or

removing/installing attachments or accessories.

An accidental start-up can causeinjury.

The following procedures must be followed when

maintenance or service is performed on the aircompressor.

1. Ensure On/Off switch is in the OFFposition.

2. Remove air compressor plug fromoutlet.

3. Drain airtank.

4. Allow air compressor to cool down before

startingservice.

NOTE: All compressed air systems contain maintenance

parts (e.g., oil, filters, separators) that are periodically

replaced. These used parts may contain substances that are

regulated and must be disposed of in accordance with local,

state, and federal laws andregulations.

NOTE: Take note of the positions and locations of parts

during disassembly to make reassemblyeasier.

NOTE: Any service operations not included in this section

should be performed by a

DeWALT factory service center or

DeWALT authorized servicecenter.

MAINTENANCE CHART

Procedure Daily Weekly Monthly 1 year or 200

Hours

Check safety valve

Inspect air filter +

Drain air tank

Check pump oil level

Change pump oil**+ X

Oil leak inspection

Check for unusual noise/

vibration

Check for air leaks*

Clean compressor exterior

* To check for air leaks apply a solution of soapy water around joints.

While compressor is pumping to pressure and after pressure cuts out,

look for air bubbles to form.

** The pump oil must be changed after the first 20 hours of operation.

Thereafter, when using SAE 5W-40 full synthetic oil, change oil every

200 hours of operation or once a year, whichever comes first.

+ Perform more frequent in dusty or humid conditions

Checking Safety Valve (Fig. B)



WARNING: Hot surfaces. Risk of burn. Aftercooler,

pump head, and surrounding parts are very hot, do

not touch (see the Hot Surfaces identified in Fig.B).

Allow compressor to cool prior toservicing.

ENGLISH



WARNING: Risk of bursting. If the safety valve does

not work properly, over-pressurization may occur,

causing air tank rupture or anexplosion.

Before starting compressor, pull the ring on the safety

valve to make sure that the safety valve operates freely. If

the valve is stuck or does not operate smoothly, it must be

replaced with the same type ofvalve.

Checking Air Filter Element (Fig. A, B)



WARNING: Hot surfaces. Risk of burn. Aftercooler,

pump head, and surrounding parts are very hot, do

not touch (see the Hot Surfaces identified in Fig.B).

Allow compressor to cool prior toservicing.

1. Ensure the On/Off switch

1

is in the OFFposition.

2. Allow unit tocool.

3. Remove air filter

14

fromunit.

4. Carefully pry filter top frombase.

5. Remove element from filterbase.

6. If element needs cleaning, blow out with air. Replace

if needed. Purchase replacement parts from your local

dealer or authorized service center. Always use identical

replacementparts.

7. Place element back in filterbase.

8. Snap filter top to filterbase.

9. Reassemble air filter to unit. Ensure exhaust outlet

pointsdown.



CAUTION: Risk of unsafe operation. Do not operate

without air inletfilter.

Draining Air Tank (Fig. A)



WARNING: Risk of unsafe operation. Risk from

noise. Air tanks contain high pressure air. Keep face

and other body parts away from outlet of drain. Use

safety glasses [ANSI Z87.1 (CAN/CSA Z94.3)] when

draining as debris can be kicked up into face. Use ear

protection [ANSI S12.6 (S3.19)] as air flow noise is loud

whendraining.

NOTE: All compressed air systems generate condensate

that accumulates in any drain point (e.g. tanks, filter,

aftercoolers, dryers). This condensate contains lubricating

oil and/or substances which may be regulated and must be

disposed of in accordance with local, state, and federal laws

andregulations.

1. Ensure On/Off switch is in the OFFposition.

2. Move compressor into an inclined position so drain

valve

8

is at the lowest point (this will assist in

removing moisture, dirt, etc. from air tanks)

3. Place a suitable container under the drain valve to

catchdischarge.

4. Grasp knurled knob on drainvalve.

5. Slowly rotate knob to gradually bleed air from airtank.



WARNING: Risk of bursting. Drain air tank daily.

Water will condense in air tank. If not drained, water

will corrode and weaken the air tank causing a risk of

air tankrupture.



CAUTION: Risk of property damage. Drain water

from air tank may contain oil and rust, which can

causestains.

6. When air tank pressure gauge reads 10 PSI (68,9 kPa),

rotate valve to the fully openposition.

7. Close drain valve whenfinished.

Compressor Pump Oil (Fig. B, N)

Checking Oil



WARNING: Hot surfaces. Risk of burn. Aftercooler,

pump head, and surrounding parts are very hot, do

not touch (see the Hot Surfaces identified in Fig.B).

Allow compressor to cool prior toservicing.

1. Ensure On/Off switch is in the OFFposition.

2. Place unit on a flat levelsurface.

3. Remove dipstick

11

and wipeclean.

4. Reinsert dipstick fully into oil fill port for a few seconds

to allow oil to collect on thedipstick.

5. Remove oil dipstick to read oil level. Oil should not

exceed top raised line on dipstick. If oil is below lower

mark, add same type of oil in crankcase and follow Steps

4 - 6. NOTE: When filling the crankcase, the oil flows

very slowly into the pump. If the oil is added too quickly,

it will overflow and appear to befull.



CAUTION: Risk of unsafe operation. Overfilling with

oil will cause premature compressor failure. Do

notoverfill.

6. Replacedipstick.

MAX

MIN

Fig. N

Changing Oil

NOTE: Pump oil contains substances that are regulated

and must be disposed of in accordance with local, state and

federal laws andregulations.



WARNING: Hot surfaces. Risk of burn. Aftercooler,

pump head, and surrounding parts are very hot, do

not touch (see the Hot Surfaces identified in Fig.B).

Allow compressor to cool prior toservicing.

1. Ensure On/Off switch is in the OFFposition.

2. Allow the unit tocool.

3. Remove air compressor plug fromoutlet.

4. Drain airtank.

5. Locate a suitable container under pump drain plug

12

6. Remove the dipstick

11

fromcrank case.

7. Remove the oil drain plug

12

ENGLISH

8. Allow ample time for all oil to drain out. (Tilting

the compressor towards the drain plug will assist

indraining.)

9. Install the oil drainplug.

10. Fill pump using SAE 5W-40 full synthetic oil.

11. Replacedipstick.

Cleaning



WARNING: Blow dirt and dust out of all air vents with

clean, dry air at least once a week. To minimize the risk

of eye injury, always wear ANSI Z87.1 approved eye

protection when performingthis.



WARNING: Never use solvents or other harsh

chemicals for cleaning the non-metallic parts of

the tool. These chemicals may weaken the plastic

materials used in these parts. Use a cloth dampened

only with water and mild soap. Never let any liquid

get inside the tool; never immerse any part of the tool

into aliquid.

Accessories



WARNING: Since accessories, other than those

offered by DeWALT, have not been tested with this

product, use of such accessories with this tool could be

hazardous. To reduce the risk of injury, only

DeWALT

recommended accessories should be used with

thisproduct.

Recommended accessories for use with your tool

are available at extra cost from your local dealer or

authorized service center. If you need assistance in

locating any accessory, please contact

DeWALT Industrial

Tool Co., 701East Joppa Road, Towson, MD 21286, call

1-800-4-DeWALT (1-800-433-9258) or visit our website:

www.dewalt.com.

Repairs

The charger and battery pack are notserviceable.



WARNING: To assure product SAFETY and

RELIABILITY, repairs, maintenance and adjustment

(including brush inspection and replacement, when

applicable) should be performed by a

DeWALT factory

service center or a DeWALT authorized service center.

Always use identical replacementparts.

Thank you for your purchase. Register your product nowfor:

• WARRANTY SERVICE: Registering your product will

help you obtain more efficient warranty service in case

there is a problem with yourproduct.

• CONFIRMATION OF OWNERSHIP: In case of

an insurance loss, such as fire, flood or theft, your

registration of ownership will serve as your proof

ofpurchase.

• FOR YOUR SAFETY: Registering your product will

allow us to contact you in the unlikely event a safety

notification is required under the Federal Consumer

SafetyAct.

Three Year Limited Warranty

DeWALT will repair, without charge, any defects due to

faulty materials or workmanship for three years from the

date of purchase. This warranty does not cover part failure

due to normal wear or tool abuse. For further detail of

warranty coverage and warranty repair information, visit

www.dewalt.com or call 1-800-4-

DeWALT (1-800-433-9258).

This warranty does not apply to accessories or damage

caused where repairs have been made or attempted by

others. This warranty gives you specific legal rights and

you may have other rights which vary in certain states

orprovinces.

In addition to the warranty,

DeWALT tools are covered

byour:

1 YEAR FREE SERVICE

DeWALT will maintain the tool and replace worn parts

caused by normal use, for free, any time during the first year

afterpurchase.

90 DAY MONEY BACK GUARANTEE

If you are not completely satisfied with the performance of

your

DeWALT Power Tool, Laser, or Nailer for any reason, you

can return it within 90 days from the date of purchase with

a receipt for a full refund – no questionsasked.

LATIN AMERICA: This warranty does not apply to products

sold in Latin America. For products sold in Latin America,

see country specific warranty information contained in

the packaging, call the local company or see website for

warrantyinformation.

FREE WARNING LABEL REPLACEMENT: If your warning

labels become illegible or are missing, call 1-800-4-

DeWALT

(1-800-433-9258) for a freereplacement.

Glossary

CFM: Cubic feet perminute.

SCFM: Standard cubic feet per minute; a unit of measure of

airdelivery.

PSI: Pounds per square inch; a unit of measure ofpressure.

kPa (kilopascal): Metric pressure measurement.

1kilopascal equal 1000pascals.

Code Certification: Products that bear one or more of the

following marks: UL, CUL, ETL, CETL, have been evaluated

by OSHA certified independent safety laboratories and

meet the applicable Underwriters Laboratories Standards

forSafety.

Cut-In Pressure: While the motor is off, air tank pressure

drops when accessory is used. When the tank pressure

drops to a certain low level the motor will restart

automatically. The low pressure at which the motor

automatically restarts is called cut-inpressure.

Cut-Out Pressure: When an air compressor is turned on

and begins to run, air pressure in the air tank begins to

build. It builds to a certain high pressure before the motor

automatically shuts off, protecting your air tank from

pressure higher than its capacity. The high pressure at which

the motor shuts off is called cut-outpressure.

Branch Circuit: The circuit carrying electricity from

electrical panel tooutlet.

ENGLISH

Duty Cycle: For proper operation of your air compressor, it

is recommended that a 50% duty cycle be maintained; that

is, the air compressor should not run more than 5 minutes

in any 10 minuteperiod.

Troubleshooting Guide

This section provides a list of the more frequently encountered malfunctions, their causes and corrective actions. The

operator or maintenance personnel can perform some corrective actions, and others may require the assistance of a

qualified DeWALT technician or yourdealer.

Problem Code

Excessive air tank pressure-safety valve pops off 1, 2

Air leaks 3

Air leaks in air tank or at air tank welds 4

Air leaks between head and valve plate 5

Air leaks from safety valve 6

Knocking noise 6,16,17

Pressure reading on the regulated pressure gauge drops when an accessory is used 7

Compressor is not supplying enough air to operate accessories 8, 9, 10, 11, 12, 15

Regulator knob has continuous air leak 13

Regulator will not shut off air outlet 13

Moisture in pump crankcase 14,18

Motor will not run 11, 19, 20, 21, 22, 23, 24, 25, 26

Troubleshooting Codes

CODE POSSIBLE CAUSE POSSIBLE SOLUTION

1 Pressure switch does not shut off motor when compressor

reaches cut-out pressure

Set the On/Off switch to OFF, if the unit does not shut off contact a D

eWALT factory

service center or a DeWALT authorized service center.

2 Pressure switch cut-out too high Contact a D

eWALT factory service center or a DeWALT authorized service center.

3 Tube fittings are not tight enough Tighten fittings where air can be heard escaping. Check fittings with soapy water

solution. Do Not Overtighten.

4 Defective air tank Air tank must be replaced. Do not repair the leak.



WARNING: Risk of bursting. Do not drill into, weld or otherwise modify

air tank or it will weaken. The air tank can rupture or explode.

5 Leaking seals Contact a D

WALT factory service center or a D

WALT authorized service center.

6 Defective safety valve Operate safety valve manually by pulling on ring. If valve still leaks, it must

be replaced.

7 Regulator is not adjusted correctly for accessory being used It is normal for some pressure drop to occur when an accessory is used, adjust the

regulator as instructed in Regulator under Features if pressure drop is excessive.

NOTE: Adjust the regulated pressure under flow conditions while accessory is

being used.

8 Prolonged excessive use of air Decrease amount of air usage.

9 Compressor is not large enough for accessory Check the accessory air requirement. If it is higher than the CFM or

pressure supplied by your air compressor, a larger compressor is needed to

operate accessory.

10 Hole in air hose Replace air hose.

11 Check valve restricted Remove, clean or replace.

12 Air leaks Tighten fittings.

13 Regulator is damaged Replace.

14 Unit operating in damp or humid conditions Move unit to a dry well ventilated area.

15 Restricted air intake filter Clean or replace air intake filter.

ENGLISH

CODE POSSIBLE CAUSE POSSIBLE SOLUTION

16 Engine or pump oil is low Add same type of oil in crankcase to pump. See Compressor Pump Oil

under Maintenance.

17 Carbon build-up in pump. Contact a D

eWALT factory service center or a DeWALT authorized service center.

18 Detergent type oil being used in pump Drain oil and refill pump using SAE 5W-40 full synthetic oil.

19 Motor overload protection switch has tripped See Motor Overload under Components.

20 Extension cord is wrong length or gauge Check for proper gauge wire and cord length. See Extension Cords

under Assembly and Adjustments.

21 Loose electrical connections Contact a D

eWALT factory service center or a DeWALT authorized service center.

22 Possible defective motor or starting capacitor Contact a D

eWALT factory service center or a DeWALT authorized service center.

23 Paint spray on internal motor parts Contact a D

eWALT factory service center or a DeWALT authorized service center. Do

not operate the compressor in the paint spray area. See flammable vapor warning.

24 Fuse blown, circuit breaker tripped Check fuse box for blown fuse and replace as necessary. Reset circuit breaker. Do

not use a fuse or circuit breaker with higher rating than that specified for your

particular branch circuit.

Check for proper fuse. Use only a time delay fuse.

Check for low voltage conditions and/or proper extension cord.

Disconnect the other electrical appliances from circuit or operate the compressor on

its own branch circuit.

25 Tank pressure exceeds pressure switch cut-in pressure Motor will start automatically when tank pressure drops below cut-in pressure of

pressure switch.

26 Pressure release valve on pressure switch has not unloaded

head pressure

Set the On/Off switch to OFF. If the valve does not open, replace switch. Contact a

eWALT factory service center or a DeWALT authorized service center.

FRANÇAIS

Définitions : symboles et termes d'alarmes sécurité

Ces guides d'utilisation utilisent les symboles et termes d'alarmes sécurité suivants pour vous prévenir de situations

dangereuses et de risques de dommages corporels ou matériels.



DANGER: indique une situation dangereuse imminente qui, si elle n’est pas évitée, entraînera la mort ou des

blessuresgraves.



AVERTISSEMENT: indique une situation potentiellement dangereuse qui, si elle n’est pas évitée, pourrait entraîner la

mort ou des blessuresgraves.



ATTENTION: indique une situation potentiellement dangereuse qui, si elle n’est pas évitée, pourrait entraîner des

blessures légères oumodérées.



(Si utilisé sans aucun terme) Indique un message propre à la sécurité.

AVIS : indique une pratique ne posant aucun risque de dommages corporels mais qui par contre, si rien n’est fait

pour l’éviter, pourrait poser des risques de dommages matériels.



AVERTISSEMENT! lire tous les avertissements de

sécurité et toutes les directives. Le non-respect des

avertissements et des directives pourrait se solder par un

choc électrique, un incendie et/ou une blessuregrave.

AVERTISSEMENT : afin de réduire le risque de blessures, lire

le mode d’emploi del’outil.



AVERTISSEMENT : Ce produit contient des produits

chimiques reconnus dans l’État de la Californie pour

causer le cancer et des anomalies congénitales ou autres

effets nuisibles sur la reproduction. Lavez-vous les mains

aprèsmanutention.



AVERTISSEMENT : Certaines poussières comme l’amiante

ou le plomb dans la peinture à base de plomb contiennent

des produits chimiques reconnus dans l’État de la Californie

pour causer le cancer et des anomalies congénitales ou

autres effets nuisibles sur la reproduction.

Interrupteur Marche/Arrêt

Manomètre du réservoir

d’air

Manomètre régulé

Régulateur de pression

Branchements rapides

Clapet

Soupape de sûreté

Soupape de purge du

réservoir d’air

Rembobineur de cordon

d’alimentation

Manocontacteur

Jauge graduée de l’huile

de la pompe

Bouchon de vidange

d’huile de la pompe

Filtre d’aspiration de l’air

(non illustré)

Poignée

Boutons de verrouillage

de la poignée

Panneau supérieur pour le

transport

Français (traduction de la notice d’instructions originale)

Fig. A

342

PAS UNE

ÉTAPE

1614

12 6

13 7

FRANÇAIS

CONSERVER TOUS LES

AVERTISSEMENTS ET TOUTES

LES DIRECTIVES POUR UN USAGE

ULTÉRIEUR



DANGER : RISQUE D’EXPLOSION

OU D’INCENDIE

Ce qui peut se produire Comment l’Éviter

Il est normal que des contacts

électriques dans le moteur

et le manocontacteur fassent

une étincelle.

Faites toujours fonctionner le

compresseur dans une zone bien

aérée sans matière combustible,

essence ou vapeur de solvant.

Si une étincelle électrique

provenant du compresseur

entre en contact avec des

vapeurs inflammables, elle peut

s’enflammer et causer un incendie

ou une explosion.

Si vous aspergez des matériaux

inflammables, placez le

compresseur à au moins 6,1 m

(20 pieds) de la zone pulvérisée.

Il est possible que vous ayez

besoin d’une longueur de

tuyau additionnelle.

Entreposez les matières

inflammables dans un

endroit sécuritaire, éloigné

du compresseur.

Le fait de limiter les ouvertures

d’aération de compresseur causera

une importante surchauffe et

pourrait causer un incendie.

Ne jamais placer d'objets contre

la pompe du compresseur ou sur

celle-ci.

Faites fonctionner le compresseur

dans un endroit aéré à au moins

30,5 cm (12 po) du mur ou de

l’obstruction qui pourrait limiter le

débit d’air frais dans les ouvertures

d’aération.

Faites fonctionner le compresseur

dans un endroit propre, sec et bien

aéré. Ne pas utiliser l’appareil à

l’intérieur ou dans un endroit exigu.

Le fonctionnement de ce produit

sans surveillance pourrait se solder

par des blessures personnelles ou

des dommages à la propriété. Afin

de réduire le risque d’incendie,

ne pas laisser le compresseur

fonctionner sans surveillance.

Être toujours présent lorsque le

produit est en marche.

Toujours éteindre et débrancher

l'appareil si non utilisé.



ATTENTION : RISQUE ASSOCIÉ

AU BRUIT

Ce qui peut se produire Comment l’Éviter

Dans certaines conditions et selon

la durée d’utilisation, le bruit

provoqué par ce produit peut

contribuer à une perte auditive.

Toujours utiliser un équipement de

sécurité homologué : protection

auditive conforme à la norme ANSI

S12.6 (S3.19).



DANGER: RISK TO BREATHING

(Asphyxiation)

Ce qui peut se produire Comment l’Éviter

Il est dangereux de respirer l’air

comprimé sortant du compresseur.

Le flux d’air peut contenir du

monoxyde de carbone, des vapeurs

toxiques ou des particules solides

provenant du réservoir d’air.

L’inhalation de ces contaminants

peut provoquer de sérieuses

blessures, voire un décès.

L’air qui s’obtient directement du

compresseur ne devrait jamais être

utilisé pour alimenter l’air destiné

à la consommation humaine.

Pour utiliser l’air produit par le

compresseur pour la respiration,

installer correctement des filtres

convenables et un équipement

de sécurité en ligne. Les filtres en

ligne et l’équipement de sécurité

utilisés avec le compresseur

doivent être capables de traiter l’air

conformément à tous les codes

locaux et fédéraux en vigueur avant

toute consommation humaine.

Les matériaux vaporisés comme la

peinture, les solvants de peinture,

les décapants, les insecticides, les

herbicides, pourraient contenir des

vapeurs nocives et du poison.

Travailler dans un endroit

ayant une bonne ventilation

transversale. Lire et respecter

les directives en matière de

sécurité imprimées sur l’étiquette

ou les fiches signalétiques des

matériaux qui sont pulvérisés.

Toujours utiliser un équipement

de sécurité homologué : une

protection respiratoire conforme

aux normes OSHA/MSHA/NIOSH,

conçue spécifiquement pour une

utilisation particulière.



DANGER : RISQUE DE BLESSURES OU DE

DOMMAGES À LA PROPRIÉTÉ LORS DU

TRANSPORT OU DU RANGEMENT

Ce qui peut se produire Comment l’Éviter

L’huile peut fuire ou se déverser.

Cela pourrait se solder par un

incendie ou un danger d’inhalation;

des blessures graves ou un décès.

Les fuites d’huile endommageront

le tapis, la peinture ou toutes

autres surfaces de véhicules ou

de remorques.

Toujours installer le compresseur

sur un revêtement protecteur

lors du transport pour protéger

le véhicule de tous dommages

associés aux fuites. Retirer

immédiatement le compresseur du

véhicule dès l’arrivée à destination.

Toujours tenir le compresseur à

niveau et ne jamais le déposer sur

son côté.

FRANÇAIS



AVERTISSEMENT : RISQUE D’ÉCLATEMENT

Réservoir d’air : Le réservoir dont est doté le

compresseur d’air porte le code « UM » (dans le cas

d’appareils munis de réservoirs supérieurs à 152 mm

(6 po) de diamètre) et il est conçu conformément à la

section VII Div. 1 de l’ASME. Tous les récipients sous

pression devraient être inspectés une fois tous les

deux ans. Pour localiser l’inspecteur des récipients sous

pression de votre région, consulter la section appropriée

des organismes gouvernementaux de l’annuaire

téléphonique ou composer le 1–800–4-

DeWALT pour

obtenir de l’aide.

Les conditions indiquées ci-après pourraient affaiblir le

réservoir d’air et se solder par une violente explosion de

celui-ci :

Ce qui peut se produire Comment l’Éviter

L’eau condensée n’est pas

correctement vidangée du réservoir

d’air provoquant ainsi la formation

de rouille et un amincissement du

réservoir d’air en acier.

Vidanger le réservoir d’air

quotidiennement ou après

chaque utilisation. Si le réservoir

présente une fuite, le remplacer

immédiatement par un nouveau

réservoir d’air ou par un

nouveau compresseur.

Modifications apportées au

réservoir d’air ou tentatives

de réparation.

Ne jamais percer un trou dans le

réservoir d’air ou ses accessoires, y

faire de la soudure ou y apporter

quelque modification que ce soit.

Ne jamais essayer de réparer un

réservoir d’air endommagé ou avec

des fuites. Le remplacer par un

nouveau réservoir d’air.

Des modifications non autorisées

de la soupape de sûreté ou de tous

autres composants qui régissent la

pression du réservoir d’air.

Le réservoir d’air a été conçu pour

supporter des pressions spécifiques

de fonctionnement. Ne faites

jamais effectuer de réglages ou

de substitutions de pièces en

vue de modifier les pressions de

fonctionnement réglées en usine.

Accessoires :

Lorsqu’on excède la pression

nominale des outils pneumatiques,

des pistolets pulvérisateurs,

des accessoires à commande

pneumatique, des pneus et

d’autres dispositifs pneumatiques,

on risque de les faire exploser ou

de les projeter et ainsi entraîner des

blessures graves.

Respecter les recommandations

du fabricant de l’équipement et

ne jamais dépasser la pression

nominale maximale permise des

accessoires. Ne jamais utiliser le

compresseur pour gonfler de petits

objets à basse pression comme

des jouets d’enfant, des ballons de

football et de basket-ball, etc.

Pneus :

Des pneus surgonflés pourraient

provoquer des blessures graves et

des dommages à la propriété.

Utiliser un manomètre pour vérifier

la pression des pneus avant chaque

utilisation et lors du gonflage;

consulter le flanc de pneu pour

obtenir la pression correcte.

REMARQUE : Des réservoirs

d’air, des compresseurs et d’autres

appareils similaires

utilisés pour gonfler les pneus

peuvent remplir de petits pneus

à ces pressions très rapidement.

Régler le régulateur de pression

d’air à une pression moindre que

celle indiquée sur le pneu. Ajouter

de l’air par petite quantité et

utiliser fréquemment le manomètre

pour empêcher un surgonflage.



AVERTISSEMENT : RISQUE DE CHOC

ÉLECTRIQUE

Ce qui peut se produire Comment l’Éviter

Votre compresseur d’air est

alimenté à l’électricité. Tout

comme n’importe quel autre

dispositif alimenté de façon

électrique, s’il n’est pas utilisé

correctement, il peut causer un

choc électrique.

Ne faites jamais fonctionner

le compresseur à l’extérieur

lorsqu’il pleut ou dans des

conditions humides.

Ne faites jamais fonctionner

le compresseur avec les

couvercles de protection enlevés

ou endommagés.

Les tentatives de réparation par

un personnel non qualifié peuvent

résulter en de graves blessures,

voire la mort par électrocution.

Tout câblage électrique ou toute

réparation nécessaire pour ce

produit doit être pris en charge par

un centre de réparation en usine

autorisé

DeWALT ou un centre de

réparation

DeWALT conformément

aux codes électriques nationaux

et locaux.

Mise à la terre

électrique : le fait de ne pas

faire une mise à la terre adéquate

de ce produit pourrait résulter

en des blessures graves voire la

mort par électrocution. Consulter

les Directives relatives

à la mise à la terre

sous Installation.

Assurez-vous que le circuit

électrique auquel le compresseur

est branché fournit une mise à

la terre électrique adéquate, une

tension appropriée et une bonne

protection des fusibles.

FRANÇAIS



AVERTISSEMENT : RISQUE PROVENANT DES

OBJETS PROJETÉS EN L’AIR

Ce qui peut se produire Comment l’Éviter

Le flux d’air comprimé peut

endommager les tissus mous de

la peau exposée et peut projeter

la poussière, des fragments, des

particules détachées et des petits

objets à haute vitesse, ce qui

entraînerait des dommages et des

blessures personnelles.

Toujours utiliser de l’équipement

de sécurité homologué : protection

oculaire conforme à la norme ANSI

Z87.1 (CAN/CSA Z94.3) munie

d’écrans latéraux lors de l’utilisation

du compresseur.

Ne jamais pointer une buse ou un

pulvérisateur vers une partie du

corps ou vers d’autres personnes ou

des animaux.

Toujours mettre le compresseur

hors tension et purger la pression

du tuyau à air et du réservoir d’air

avant d’effectuer l’entretien, de

fixer des outils ou des accessoires.



AVERTISSEMENT : ATTENTION SURFACES

CHAUDES

Ce qui peut se produire Comment l’Éviter

Toucher à du métal exposé

comme la tête du compresseur

ou du moteur, la tubulure des gaz

d’échappement ou de sortie, peut

se solder en de sérieuses brûlures.

Ne jamais toucher à des

pièces métalliques exposées

sur le compresseur pendant

ou immédiatement après son

utilisation. Le compresseur reste

chaud pendant plusieurs minutes

après son utilisation.

Ne pas toucher ni effectuer

des réparations aux coiffes de

protection avant que l’appareil

n’ait refroidi



AVERTISSEMENT : RISQUE DE BLESSURE

EN SOULEVANT LE PRODUI

Ce qui peut se produire Comment l’Éviter

Soulever un objet trop lourd peut

se solder par de graves blessures.

Le compresseur est trop lourd

pour être soulevé par une seule

personne. Demander de l’aide

avant de le soulever.



AVERTISSEMENT : RISQUE ASSOCIÉ

AUX PIÈCES MOBILES

Ce qui peut se produire Comment l’Éviter

Les pièces mobiles comme une

poulie, un volant ou une courroie

peuvent provoquer de graves

blessures si elles entrent en contact

avec vous ou vos vêtements.

Ne jamais utiliser le compresseur

si les protecteurs ou les couvercles

sont endommagés ou retirés.

Tenir les cheveux, les vêtements et

les gants hors de portée des pièces

en mouvement. Les vêtements

amples, bijoux ou cheveux longs

peuvent s’enchevêtrer dans les

pièces mobiles.

S’éloigner des évents car ces

derniers pourraient camoufler des

pièces mobiles.

Utiliser le compresseur avec

des pièces endommagées ou

manquantes ou le réparer sans

coiffes de protection risque

de vous exposer à des pièces

mobiles et peut se solder par de

graves blessures.

Toutes les réparations requises pour

ce produit devraient être effectuées

par un centre de réparation de

l’usine D

eWALT ou un centre de

réparation autorisé DeWALT.



AVERTISSEMENT : RISQUE ASSOCIÉ À

UTILISATION DANGEREUSE

Ce qui peut se produire Comment l’Éviter

Une utilisation dangereuse de

votre compresseur d’air pourrait

provoquer de graves blessures,

voire votre décès ou celle

d’autres personnes.

Revoir et comprendre toutes les

directives et les avertissements

contenus dans le présent mode

d’emploi.

Se familiariser avec le

fonctionnement et les commandes

du compresseur d’air.

Dégager la zone de travail de toutes

personnes, animaux et obstacles.

Tenir les enfants hors de portée du

compresseur d’air en tout temps.

Ne pas utiliser le produit en cas de

fatigue ou sous l’emprise d’alcool

ou de drogues. Rester vigilant en

tout temps.

Ne jamais rendre inopérant

les fonctionnalités de sécurité

du produit.

Installer un extincteur dans la zone

de travail.

Ne pas utiliser l’appareil lorsqu’il

manque des pièces ou que

des pièces sont brisées ou

non autorisées.

Ne jamais se tenir debout sur

le compresseur.



AVERTISSEMENT : RISQUE DE CHUTE

Ce qui peut se produire Comment l’Éviter

Un compresseur portatif peut tomber

d’une table, d’un établi ou d’un toit et

causer des dommages au compresseur,

ce qui pourrait résulter en de graves

blessures, voire la mort de l’opérateur.

Toujours faire fonctionner le

compresseur alors qu’il est dans

uns position sécuritaire et stable

afin d’empêcher un mouvement

accidentel de l’appareil. Ne jamais

faire fonctionner le compresseur

sur un toit ou sur toute autre

position élevée. Utiliser un tuyau

d’air supplémentaire pour atteindre

les emplacements en hauteur.

CONSERVER CES CONSIGNES POUR

UTILISATION ULTÉRIEURE

FRANÇAIS

Consigne de sécurité supplémentaire



AVERTISSEMENT: les scies, meules, ponceuses,

perceuses ou autres outils de construction peuvent

produire des poussières contenant des produits

chimiques reconnus par l’État californien pour causer

cancers, malformations congénitales ou être nocifs au

système reproducteur. Parmi ces produits chimiques,

on retrouve:

• Le plomb dans les peintures à base de plomb;

• La silice cristallisée dans les briques et le ciment,

ou autres produits de maçonnerie; et

• L’arsenic et le chrome dans le bois ayant subi un

traitementchimique.

Le risque associé à de telles expositions varie selon la

fréquence à laquelle on effectue ces travaux. Pour réduire

toute exposition à ces produits: travailler dans un endroit

bien aéré, en utilisant du matériel de sécurité homologué, tel

un masque antipoussières spécialement conçu pour filtrer les

particulesmicroscopiques.

• Limiter toute exposition prolongée avec les

poussières provenant du ponçage, sciage, meulage,

perçage ou toute autre activité de construction.

Porter des vêtements de protection et nettoyer à

l’eau savonneuse les parties du corps exposées. Le

fait de laisser la poussière pénétrer dans la bouche, les

yeux ou la peau peut favoriser l’absorption de produits

chimiquesdangereux.



AVERTISSEMENT: cet outil peut produire et/

ou répandre de la poussière susceptible de causer

des dommages sérieux et permanents au système

respiratoire. Utiliser systématiquement un appareil

de protection des voies respiratoires homologué par

le NIOSH ou l’OSHA. Diriger les particules dans le sens

opposé au visage et aucorps.

DESCRIPTION (FIG. A–G)



AVERTISSEMENT: ne jamais modifier l’outil

électrique ni aucun de ses composants, car il y a

risques de dommages corporels oumatériels.

Reportez-vous en FigureA au début de ce manuel pour

obtenir la liste complète descomposants.

Fiche technique

Modèle

D55154

Poids

37,3 kg (82 livres)

Hauteur

508 mm (20 po)

Largeur

469,9 mm (18,5 po)

Longueur

584,2 mm (23,0 po)

Capacité du réservoir d’air (litres)

15,1 (4,0 gallon)

Pression D’enclenchement Approx.

655 kPa (95 PSI)

Env. Pression de déclenchement

861,8 kPa (125 PSI)

PCMS (SCFM) @ 100 PSI (620,5 kPa)

3,8

Moteur

1,1 CV (continu)

Volts/Amps/Hertz 120V/14 A/60 Hz.

Régime 3450 tr/mn

Exigence minimale du circuit de

dérivation

15 A

Capacité d'huile de la pompe 354,9 ml (12 onces)

Cycle De Service

5 Minutes En Marche,

5 Minutes Arrêté

TUBE DE

SORTIE

CLAPET

TÊTE DE POMPE

ET CYLINDR

Fig. B

Interrupteur Marche/Arrêt

Mettre cet interrupteur

1

sur la position MARCHE pour

avoir une alimentation automatique au manocontacteur et

sur la position ARRÊT pour la mise hors tension à la fin de

chaqueutilisation.

Manocontacteur

Le manocontacteur

10

démarre automatiquement le

moteur lorsque la pression du réservoir d’air chute sous

la pression d’enclenchement réglée en usine. Il arrête

le moteur lorsque la pression du réservoir d’air atteint la

pression de déclenchement réglée enusine.

Fig. C

La page charge ...

DeWalt D55154 Manuel utilisateur

Marque: DeWalt

Modèle: D55154

Catégorie: Compresseurs d'air

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: DeWalt D55154 User manual
español: DeWalt D55154 Manual de usuario

DeWalt D55154 Manuel utilisateur

DeWalt D55154 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents