Intermec MobileLAN access WA22 Guide de démarrage rapide
- Taper
- Guide de démarrage rapide
MyriadPro
Intermec’s MobileLAN™access family of access points delivers reliable and seamless wireless
performance in almost any operational environment. The MobileLAN access WA22 is
powered by power over Ethernet to make installation easier. It is designed for standards-
based connectivity and it may have up to two of the following radios installed:
• IEEE 802.11a
• IEEE 802.11g
The WA22 with an IEEE 802.11a radio installed is Wi-Fi® certified
for interoperability with other 802.11a wireless LAN devices.
The WA22 with an IEEE 802.11g radio installed is Wi-Fi® certified
for interoperability with other 802.11g and 802.11b wireless
LAN devices.
This quick start guide supports the WA22B and helps you to understand its ports and LEDs.
You can also use this quick start guide to get an overview of how to install the WA22, how to
connect the WA22 to power and to your network, and how to use the MobileLAN access
Utility to configure its IP address. Once you assign the WA22 an IP address, you can continue
configuring it using a web browser interface or a telnet session.
For complete instructions on how to install, operate, configure, maintain, and troubleshoot
your WA22, see the MobileLAN access WA2X System Manual (P/N 073915). Please visit the
Intermec web site at www.intermec.com to download this manual and other current
manuals in PDF. Or, you can order printed documentation from your local Intermec
representative.
Out of the Box
MobileLAN
™
access WA22
Heading 1
About the WA22
Safety First
Quick Start Guide
Specifications
Software Updates
MobileLAN access WA22 Quick Start Guide
*074745-002*
P/N 074745-002
Physical dimensions 4.6 cm x 16.0 cm x 25.0 cm
(1.81 in x 6.27 in x 9.84 in)
Power over Ethernet
electrical rating x 48V, 315 mA
Operating temperature -20°C to 55°C (-4°F to 131°F)
Storage temperature -40°C to 70°C (-40°F to 158°F)
Humidity 10 to 90%, non-condensing
Government regulatory agencies require that this access point only use
approved antennas. Therefore, this access point uses a custom antenna
connector. Do not use antennas that are not approved for use with this
access point.
Attention: Les organismes de réglementation gouvernementaux exigent
que ce point d’accès. Par conséquent, le point d’accès est doté d’un
connecteur d’antenne personnalisé. N’utilisez pas des antennes qui ne sont
pas approuvées.
The WA22 is intended to be powered only from an Ethernet host that
complies with the IEEE 802.3af specification for power over Ethernet (POE).
Attention: Le WA22 est conçu pour être alimenté à partir d’un hôte Ethernet
qui est conforme à la spécification IEEE 802.3af pour l’alimentation par
Ethernet (POE, de l’anglais Power Over Ethernet).
This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit (http://www.openssl.org).
This product includes cryptographic software written by Eric Young ([email protected]).
Note: The WA22 does not ship with an antenna (except one 802.11a radio
configuration that ships with non-removable antennas). For a list of antennas and
antenna accessories, see the MobileLAN access WA2X System Manual or contact your
local Intermec representative.
You should check the Intermec web site for the most up-to-date software downloads and
documentation.
At www.intermec.com, click Service & Support. The Intermec Global Sales & Service
window appears.
From the Task Menu, click Downloads.
From the Select A Product field, choose Network: MobileLAN™access WA22. A screen
appears with a table of available software for the WA22.
Click the software you want to download. Follow the prompts to download the files to
your PC. For help upgrading your access point software, follow the instructions in the
MobileLAN access WA2X System Manual.
To check for the latest documentation, from the Task Menu, click Manuals.
From the Select A Product field, choose Network: MobileLAN™access WA22. A screen
appears with a list of available manuals for the WA22.
Click the manual you would like to view (in PDF). Or, to order printed versions of
Intermec manuals, contact your local Intermec representative.
1
2
3
4
7
5
6
6001 36th Avenue West
Everett, Washington 98203
U.S.A.
tel 425.348.2600
fax 425.355.9551
www.intermec.com
©
2005 Intermec Technologies
Corporation. All rights reserved.
MobileLAN access WA22
Document
package
MobileLAN access
Tools CD
Mounting
bracket and
shoulder
screws (4)
MyriadPro
Defining the LEDs and Ports
MobileLAN
™
access WA22 Quick Start Guide
1
Mounting the WA22
Attach antennas to the WA22. Intermec offers a variety of antennas and antenna
accessories. For a complete list, see the MobileLAN access WA2X System Manual.
Connect the WA22 to your network. You can either use an Ethernet cable to
connect the Ethernet port to an Ethernet drop, or you can use the fiber optic port
option. For help connecting the WA22 to a fiber optic network, see “Connecting to
Your Fiber Optic Network” in the MobileLAN access WA2X System Manual.
To power the WA22, use an Ethernet cable to connect the Ethernet port to a
MobileLAN power bridge, a Cisco power bridge, or another 802.3af-compliant
power bridge. For help, see the documentation that shipped with your power
bridge.
3
4
Setting an Initial IP Address
1
2
Install the MobileLAN access Utility by inserting the enclosed CD, clicking Install
Software, and following the instructions that appear on your screen. You can also
download the software from the Intermec web site.
Note: Your PC must be on the same Ethernet segment as the access point.
Or, if your PC is communicating wirelessly with the access point, you must
have an active radio connection.
Start the utility.
Configure parameters A through C. See the screen to the right.
Reboot the access point by disconnecting it from and reconnecting it to a power
source.
Immediately, click Set. The Status box lets you know when the new IP address is
successfully set.
1
5
4
3
2
Congratulations!
Your wireless end devices can now begin transmitting data packets through the WA22 to
your wired network. To continue configuring the access point, from the Actions menu
choose Configure Access Point. Your web browser application (for example, Internet
Explorer) starts and the Access Point Login screen appears.
Connecting the WA22
You can place the WA22 on a stable surface or you can mount it to a wall or beam using the
wall bracket.
To use the mounting bracket
Insert one shoulder screw into each of the brass
inserts and tighten securely.
Using the mounting bracket as a template, mark
the location of the mounting holes on the
mounting surface.
Drill the holes.
Position the bracket on the wall with the arrow
pointing up and use mounting screws that you
provide to secure the bracket to the wall.
Note: Intermec offers a variety of mounting bracket kits. For a complete list, see the
MobileLAN access WA2X System Manual.
1
2
3
4
5
6
Route the Ethernet cable
through the cable
routing channels.
Mount the WA22 in the
bracket by inserting the
shoulder screws into the
keyhole slots in the
bracket. Slide the WA22
down until it is firmly
seated in the bracket.
3
3
Mounting the WA22 (continued)
2
To MobileLAN
power bridge
Mounting
screws
(2-6 places)
Cable routing
channels
Mounting
bracket
Shoulder
screws
(4 places)
Brass
inserts
A
Click the down arrow and
choose Set IP Address.
B
Enter the Ethernet MAC
address of the access point
(printed on the label on the
access point).
C
Enter the new IP address of
the access point.
Ready-to-Work™ Indicator
Blue LED flashes if the WA22 is
searching for the root access
point in the network. Remains
on when the access point is
ready for use, indicating that it
either found a root or became
the root.
Serial port
10BaseT/100BaseTX
Ethernet port
Fiber optic
port
(optional)
Power
Remains on after
the WA22 boots.
Wireless #1
Flashes when a frame is
transmitted or received on
the radio port for the radio
installed in radio slot 1.
Wireless #2
Flashes when a frame is
transmitted or received on
the radio port for the radio
installed in radio slot 2 (if a
second radio is installed).
Wired LAN
Flashes when a
frame is transmitted
or received on the
Ethernet port.
-
1
-
2
Intermec MobileLAN access WA22 Guide de démarrage rapide
- Taper
- Guide de démarrage rapide
dans d''autres langues
Documents connexes
-
Intermec MobileLAN access WA22 Guide de démarrage rapide
-
-
Intermec MaxiScan 2100 Guide de démarrage rapide
-
Intermec MobileLAN access Manuel utilisateur
-
-
-
-
-
-
Intermec MobileLAN access 2102 Guide de démarrage rapide