Dremel PawControl 7760-PGK Operating/Safety Instructions Manual

IMPORTANT

Read Before Using

●

IMPORTANT

Lire avant usage

●

IMPORTANTE

Leer antes de usar

1-800-4-DREMEL (1-800-437-3635) www.dremel.com

Operating/Safety Instructions

Consignes d’utilisation/de sécurité

Instrucciones de funcionamiento y seguridad

For English Version

See page 2

●

Version française

Voir page 37

●

Versión en español

Ver la página 76

Call Toll Free for Consumer Information and Service Locations

Pour obtenir des informations et les adresses de nos centres de service après-vente, appelez ce numéro gratuit

Llame gratis para obtener información para el consumidor y ubicaciones de servicio

P.O. Box 081126 Racine, WI 53408-1126

Dremel PawControl 7760-PGK

1600A01P55.qxp_7760-PGK 4/15/19 9:55 AM Page 1

2

Safety Symbols

The definitions below describe the level of severity for each signal word. Please read the

manual and pay attention to these symbols.

!

This is the safety alert symbol. It is used to alert you to potential

personal injury hazards. Obey all safety messages that follow this

symbol to avoid possible injury or death.

DANGER indicates a hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING indicates a hazardous situation which, if not avoided,

could result in death or serious injury.

CAUTION indicates a hazardous situation which, if not avoided,

could result in minor or moderate injury.

INSTRUCTIONS PERTAINING TO A RISK OF FIRE,

ELECTRIC SHOCK, OR INJURY TO PERSONS

Safety Rules for Pet Grooming

When using electrical appliances, basic precautions should always be

followed, including the following:

SAVE THESE INSTRUCTIONS

a) Read all the instructions before using the

appliance

b) To reduce the risk of injury, close

supervision is necessary when appliance

is used near children

c) Do not contact moving parts

d) Only use attachments recommended or

sold by the manufacturer

e) Do not use outdoors

f) To reduce the risk of electrical shock, do

not put 7760-PGK in water or other liquid.

Do not place or store appliance where it

can fall or be pulled into a tub or sink.

g) Use only the power adapter

recommended by the manufacturer to

recharge.

Keep away from water. Use extra caution

when using rotary tool near a tub or pet

washing area. Water entering a power tool

will increase the risk of electric shock.

Use personal protective equipment.

Always wear eye protection.

This product is intended only for grooming

the toenails of a dog or cat. This product is

not intended for use as a dental drill, in

human or veterinary medical applications.

Serious injury may result.

Use only sanding disc accessory SD60-PGA

and EZ Lock™ mandrel EZ402 with

AT01-PGA attachment. Use of any other

accessory may result in serious injury.

Do not use AT01-PGA attachment without

all components installed according to

operating instructions. Any other use is a

misuse and could result in injury.

Recommended maximum operating speed

for most pet grooming applications is

10,000/min. Recommended speed setting

is "1". Nail thickness and other factors

may require use of higher speeds. Use

extreme caution when operating at higher

speeds and limit the amount of time that

Read all safety warnings and all instructions. Failure to follow the

warnings and instructions may result in fire and/or serious injury to a

person or animal.

1600A01P55.qxp_7760-PGK 4/15/19 9:55 AM Page 2

3

Safety Rules for Pet Grooming

the nail is exposed to the sanding surface.

Use of higher operating speeds may cause

heat buildup and injury to the pet. Always

monitor pet for signs of discomfort and stop

grooming if observed.

Keep pet hair away from spinning parts.

Hair can entangle in the tool, causing injury

to your pet. Refer to ‘Pet Safety Tips’

section for more information.

 Work area safety

Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust. Power

tools create sparks which may ignite the

dust or fumes.

Keep children and bystanders away while

operating a power tool. Distractions can

cause you to lose control.

 Electrical safety

Power tool plugs must match the outlet.

Never modify the plug in any way. Do not

use any adapter plugs with earthed

(grounded) power tools. Unmodified plugs

and matching outlets will reduce risk of

electric shock.

Avoid body contact with earthed or

grounded surfaces such as pipes,

radiators, ranges and refrigerators. There

is an increased risk of electric shock if your

body is earthed or grounded.

Do not expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock.

Do not abuse the cord. Never use the cord

for carrying, pulling or unplugging the

power tool. Keep cord away from heat, oil,

sharp edges or moving parts. Damaged or

entangled cords increase the risk of electric

shock.

When operating a power tool outdoors,

use an extension cord suitable for outdoor

use. Use of a cord suitable for outdoor use

reduces the risk of electric shock.

If operating a power tool in a damp

location is unavoidable, use a Ground Fault

Circuit Interrupter (GFCI) protected

supply. Use of an GFCI reduces the risk of

electric shock.

 Personal safety

Stay alert, watch what you are doing and

use common sense when operating a

power tool. Do not use a power tool while

you are tired or under the influence of

drugs, alcohol or medication. A moment of

inattention while operating power tools may

result in serious personal injury.

Use personal protective equipment.

Always wear eye protection. Protective

equipment such as dust mask, non-skid

safety shoes, hard hat, or hearing protection

used for appropriate conditions will reduce

personal injuries.

Prevent unintentional starting. Ensure the

switch is in the off-position before

connecting to power source and / or

battery pack, picking up or carrying the

tool. Carrying power tools with your finger

on the switch or energizing power tools that

have the switch on invites accidents.

Remove any adjusting key or wrench

before turning the power tool on. A wrench

or a key left attached to a rotating part of

the power tool may result in personal injury.

Do not overreach. Keep proper footing and

balance at all times. This enables better

control of the power tool in unexpected

situations.

Dress properly. Do not wear loose clothing

or jewelry. Keep your hair, clothing and

gloves away from moving parts. Loose

clothes, jewelry or long hair can be caught

in moving parts.

If devices are provided for the connection

of dust extraction and collection facilities,

Read all safety warnings and all instructions. Failure to follow the

warnings and instructions may result in electric shock, fire and/or serious

injury.

SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE

The term “power tool” in the warnings refers to your mains-operated (corded) power tool

or battery-operated (cordless) power tool.

General Power Tool Safety Warnings

1600A01P55.qxp_7760-PGK 4/15/19 9:55 AM Page 3

4

 Safety warnings common for

grinding, sanding, wire

brushing, polishing, carving

or abrasive cutting-off

operations:

This power tool is intended to function as

a grinder, sander, wire brush, polisher,

carving or cut-off tool. Read all safety

warnings, instructions, illustrations and

specifications provided with this power

tool. Failure to follow all instructions listed

below may result in electric shock, fire

and/or serious injury.

Do not use accessories which are not

specifically designed and recommended by

the tool manufacturer. Just because the

accessory can be attached to your power

tool, it does not assure safe operation.

The RATED SPEED of the accessories must

Safety Rules for Rotary Tools

ensure these are connected and properly

used. Use of dust collection can reduce

dust-related hazards.

 Power tool use and care

Do not force the power tool. Use the

correct power tool for your application.

The correct power tool will do the job

better and safer at the rate for which it was

designed.

Do not use the power tool if the switch

does not turn it on and off. Any power tool

that cannot be controlled with the switch is

dangerous and must be repaired.

Disconnect the plug from the power

source and/or the battery pack from the

power tool before making any

adjustments, changing accessories, or

storing power tools. Such preventive safety

measures reduce the risk of starting the

power tool accidentally.

Store idle power tools out of the reach of

children and do not allow persons

unfamiliar with the power tool or these

instructions to operate the power tool.

Power tools are dangerous in the hands of

untrained users.

Maintain power tools. Check for

misalignment or binding of moving parts,

breakage of parts and any other condition

that may affect the power tool’s operation.

If damaged, have the power tool repaired

before use. Many accidents are caused by

poorly maintained power tools.

Keep cutting tools sharp and clean.

Properly maintained cutting tools with

sharp cutting edges are less likely to bind

and are easier to control.

Use the power tool, accessories and tool

bits etc. in accordance with these

instructions, taking into account the

working conditions and the work to be

performed. Use of the power tool for

operations different from those intended

could result in a hazardous situation.

 Battery tool use and care

Recharge only with the charger specified

by the manufacturer. A charger that is

suitable for one type of battery pack may

create a risk of fire when used with another

battery pack.

Use power tools only with specifically

designated battery packs. Use of any other

battery packs may create a risk of injury and

fire.

When battery pack is not in use, keep it

away from other metal objects like paper

clips, coins, keys, nails, screws, or other

small metal objects that can make a

connection from one terminal to another.

Shorting the battery terminals together may

cause burns or a fire.

Under abusive conditions, liquid may be

ejected from the battery, avoid contact. If

contact accidentally occurs, flush with

water. If liquid contacts eyes, additionally

seek medical help. Liquid ejected from the

battery may cause irritation or burns.

 Service

Have your power tool serviced by a

qualified repair person using only identical

replacement parts. This will ensure that the

safety of the power tool is maintained.

Do not modify or attempt to repair the tool

or the battery pack except as indicated in

the instructions for use and care.

General Power Tool Safety Warnings

1600A01P55.qxp_7760-PGK 4/15/19 9:55 AM Page 4

5

Safety Rules for Rotary Tools

be at least equal to the operating speed

setting marked on the power tool.

Accessories running faster than their RATED

SPEED can break and fly apart.

The outside diameter and the thickness of

your accessory must be within the

capacity rating of your power tool.

Incorrectly sized accessories cannot be

adequately controlled.

The arbor size of wheels, sanding drums or

any other accessory must properly fit the

spindle or collet of the power tool.

Accessories that do not match the mounting

hardware of the power tool will run out of

balance, vibrate excessively and may cause

loss of control.

Mandrel mounted wheels, sanding drums,

cutters or other accessories must be fully

inserted into the collet or chuck. If the

mandrel is insufficiently held and/or the

overhang of the wheel is too long, the

mounted wheel may become loose and be

ejected at high velocity.

Do not use a damaged accessory. Before

each use inspect the accessory such as

abrasive wheels for chips and cracks,

sanding drum for cracks, tear or excess

wear, wire brush for loose or cracked

wires. If power tool or accessory is

dropped, inspect for damage or install an

undamaged accessory. After inspecting

and installing an accessory, position

yourself and bystanders away from the

plane of the rotating accessory and run the

power tool at maximum no-load speed for

one minute. Damaged accessories will

normally break apart during this test time.

Wear personal protective equipment.

Depending on application, use face shield,

safety goggles or safety glasses. As

appropriate, wear dust mask, hearing

protectors, gloves and workshop apron

capable of stopping small abrasive or

workpiece fragments. The eye protection

must be capable of stopping flying debris

generated by various operations. The dust

mask or respirator must be capable of

filtrating particles generated by your

operation. Prolonged exposure to high

intensity noise may cause hearing loss.

Keep bystanders a safe distance away

from work area. Anyone entering the work

area must wear personal protective

equipment. Fragments of workpiece or of a

broken accessory may fly away and cause

injury beyond immediate area of operation.

Hold power tool by insulated gripping

surfaces only, when performing an

operation where the cutting accessory may

contact hidden wiring. Cutting accessory

contacting a “live” wire may make exposed

metal parts of the power tool “live” and

could give the operator an electric shock.

Always hold the tool firmly in your hand(s)

during the start-up. The reaction torque of

the motor, as it accelerates to full speed,

can cause the tool to twist.

Use clamps to support workpiece

whenever practical. Never hold a small

workpiece in one hand and the tool in the

other hand while in use. Clamping a small

workpiece allows you to use your hand(s) to

control the tool. Round material such as

dowel rods, pipes or tubing have a tendency

to roll while being cut, and may cause the

bit to bind or jump toward you.

Position the cord clear of the spinning

accessory. If you lose control, the cord may

be cut or snagged and your hand or arm

may be pulled into the spinning accessory.

Never lay the power tool down until the

accessory has come to a complete stop. The

spinning accessory may grab the surface and

pull the power tool out of your control.

After changing the bits or making any

adjustments, make sure the collet nut,

chuck or any other adjustment devices are

securely tightened. Loose adjustment

devices can unexpectedly shift, causing loss

of control, loose rotating components will

be violently thrown.

Do not run the power tool while carrying it

at your side. Accidental contact with the

spinning accessory could snag your

clothing, pulling the accessory into your

body.

Regularly clean the power tool’s air vents.

The motor’s fan will draw the dust inside

the housing and excessive accumulation of

powdered metal may cause electrical

hazards.

Do not operate the power tool near

flammable materials. Sparks could ignite

these materials.

Do not use accessories that require liquid

coolants. Using water or other liquid

coolants may result in electrocution or

shock.

Use only in well-ventilated area. Working in

a safe environment reduces risk of injury.

Allow for sufficient space, at least 6”,

between your hand and the spinning bit.

Do not reach in the area of the spinning

bit. The proximity of the spinning bit to your

hand may not always be obvious.

1600A01P55.qxp_7760-PGK 4/15/19 9:55 AM Page 5

6

Do not touch the bit or collet after use.

After use the bit and collet are too hot to be

touched by bare hands.

Do not alter or misuse tool. Any alteration

or modification is a misuse and may result

in serious personal injury.

This product is not intended for use as a

dental drill, in human or veterinary medical

applications. Serious injury may result.

 Kickback and Related

Warnings

Kickback is a sudden reaction to a pinched

or snagged rotating wheel, backing pad,

brush or any other accessory. Pinching or

snagging causes rapid stalling of the

rotating accessory which in turn causes the

uncontrolled power tool to be forced in the

direction opposite of the accessory’s

rotation.

For example, if an abrasive wheel is

snagged or pinched by the workpiece, the

edge of the wheel that is entering into the

pinch point can dig into the surface of the

material causing the wheel to climb out or

kickout. The wheel may either jump toward

or away from the operator, depending on

direction of the wheel’s movement at the

point of pinching. Abrasive wheels may also

break under these conditions.

Kickback is the result of power tool misuse

and/or incorrect operating procedures or

conditions and can be avoided by taking

proper precautions as given below.

Maintain a firm grip on the power tool and

position your body and arm to allow you to

resist kickback forces. The operator can

control kickback forces, if proper

precautions are taken.

Use special care when working corners,

sharp edges etc. Avoid bouncing and

snagging the accessory. Corners, sharp

edges or bouncing have a tendency to snag

the rotating accessory and cause loss of

control or kickback.

Do not attach a toothed saw blade. Such

blades create frequent kickback and loss of

control.

Always feed the bit into the material in the

same direction as the cutting edge is

exiting from the material (which is the

same direction as the chips are thrown).

Feeding the tool in the wrong direction

causes the cutting edge of the bit to climb

out of the work and pull the tool in the

direction of this feed.

When using rotary files, cut-off wheels,

high-speed cutters or tungsten carbide

cutters, always have the work securely

clamped. These wheels will grab if they

become slightly canted in the groove, and

can kickback. When a cut-off wheel grabs,

the wheel itself usually breaks. When a

rotary file, high-speed cutter or tungsten

carbide cutter grabs, it may jump from the

groove and you could lose control of the

tool.

 Safety warnings specific for

grinding and abrasive cutting-

off operations:

Use only wheel types that are

recommended for your power tool and

only for recommended applications. For

example: do not grind with the side of a

cut-off wheel. Abrasive cut-off wheels are

intended for peripheral grinding, side forces

applied to these wheels may cause them to

shatter.

For threaded abrasive cones and plugs use

only undamaged wheel mandrels with an

unrelieved shoulder flange that are of

correct size and length. Proper mandrels

will reduce the possibility of breakage.

Do not jam a cut-off wheel or apply

excessive pressure. Do not attempt to

make an excessive depth of cut.

Overstressing the wheel increases the

loading and susceptibility to twisting or

snagging of the wheel in the cut and the

possibility of kickback or wheel breakage.

Do not position your hand in line with and

behind the rotating wheel. When the wheel,

at the point of operation, is moving away

from your hand, the possible kickback may

propel the spinning wheel and the power

tool directly at you.

When wheel is pinched, snagged or when

interrupting a cut for any reason, switch

off the power tool and hold the power tool

motionless until the wheel comes to a

complete stop. Never attempt to remove

the cut-off wheel from the cut while the

wheel is in motion otherwise kickback may

occur. Investigate and take corrective action

to eliminate the cause of wheel pinching or

snagging.

Do not restart the cutting operation in the

workpiece. Let the wheel reach full speed

and carefully re-enter the cut. The wheel

may bind, walk up or kickback if the power

tool is restarted in the workpiece.

Safety Rules for Rotary Tools

1600A01P55.qxp_7760-PGK 4/15/19 9:55 AM Page 6

7

Safety Rules for Rotary Tools

GFCI and personal protection devices like

electrician’s rubber gloves and footwear will

further enhance your personal safety.

Do not use AC only rated tools with a DC

power supply. While the tool may appear to

work, the electrical components of the AC

rated tool are likely to fail and create a

hazard to the operator.

Keep handles dry, clean and free from oil

and grease. Slippery hands cannot safely

control the power tool.

Develop a periodic maintenance schedule

for your tool. When cleaning a tool be

careful not to disassemble any portion of

the tool since internal wires may be

misplaced or pinched or safety guard

return springs may be improperly

mounted. Certain cleaning agents such as

gasoline, carbon tetrachloride, ammonia,

etc. may damage plastic parts.

Some dust created by

power sanding, sawing,

grinding, drilling, and other construction

activities contains chemicals known to

cause cancer, birth defects or other

reproductive harm. Some examples of

these chemicals are:

• Lead from lead-based paints,

• Crystalline silica from bricks and cement

and other masonry products, and

• Arsenic and chromium from chemically-

treated lumber.

Your risk from these exposures varies,

depending on how often you do this type of

work. To reduce your exposure to these

chemicals: work in a well ventilated area,

and work with approved safety equipment,

such as those dust masks that are specially

designed to filter out microscopic particles.

Additional Safety Warnings

Support panels or any oversized

workpiece to minimize the risk of wheel

pinching and kickback. Large workpieces

tend to sag under their own weight.

Supports must be placed under the

workpiece near the line of cut and near the

edge of the workpiece on both sides of the

wheel.

Use extra caution when making a pocket

cut into existing walls or other blind

areas. The protruding wheel may cut gas or

water pipes, electrical wiring or objects that

can cause kickback.

 Safety warnings specific for

wire brushing operations:

Be aware that wire bristles are thrown by

the brush even during ordinary operation.

Do not overstress the wires by applying

excessive load to the brush. The wire

bristles can easily penetrate light clothing

and/or skin.

Allow brushes to run at operating speed

for at least one minute before using them.

During this time no one is to stand in front

or in line with the brush. Loose bristles or

wires will be discharged during the run-in

time.

Direct the discharge of the spinning wire

brush away from you. Small particles and

tiny wire fragments may be discharged at

high velocity during the use of these

brushes and may become imbedded in your

skin.

1600A01P55.qxp_7760-PGK 4/15/19 9:55 AM Page 7

8

Safety Rules for Charging

This manual contains

instructions for power

adapter model 510. If power adapter is not

included, only charge tool using a listed Class

2 USB power adapter rated 5V/1A minimum.

Before using power adapter, read all

instructions and cautionary markings on

(1) power adapter, and (2) product using

battery.

Charge only Dremel PawControl 7760-PGK.

Other types of cordless tools may burst

causing personal injury and damage.

Charge tool in temperatures above +32

degrees F (0 degrees C) and below +113

degrees F (45 degrees C). Store tool in

locations where temperatures will not

exceed 122 degrees F (50 degrees C). This

is important to prevent serious damage to

the battery cells.

Do not recharge tool in damp or wet

environment. Do not expose power

adapter to rain or snow. Water entering

power adapter may result in electric shock

or fire.

Battery leakage may occur under extreme

usage or temperature conditions. Avoid

contact with skin and eyes. The battery

liquid is caustic and could cause chemical

burns to tissues. If liquid comes in contact

with skin, wash quickly with soap and

water. If the liquid contacts your eyes, flush

them with water for a minimum of 10

minutes and seek medical attention.

Place tool on flat nonflammable surfaces

and away from flammable materials when

recharging. Carpeting and other heat

insulating surfaces block proper air

circulation, which may cause overheating of

the power adapter and tool. If smoke or

melting of the power adapter or tool is

observed, unplug the charger immediately

and do not use the tool or charger. Contact

customer service immediately.

Make sure that USB cable is located so

that it will not be stepped on, tripped over,

or otherwise subjected to damage or

stress. Damaged plug and cable may result

in electric shock or fire.

Disconnect the tool from the power

adapter by pulling the plug rather than the

cable. Do not operate power adapter with

damaged USB cable or plug; have them

replaced immediately. Damaged plug or

cable may result in electric shock or fire.

Do not disassemble power adapter or

operate the power adapter if it has

received a sharp blow, been dropped or

otherwise damaged in anyway. Incorrect

reassembly or damage may result in electric

shock or fire.

Before each use, check the power supply,

USB cable and plug. If damage is detected,

do not use the power adapter. Never open

the power adapter yourself, take it to a

Dremel Factory Service Center, or

qualified serviceman only using original

spare parts. Incorrect reassembly may

result in electric shock or fire.

Do not use attachments not recommended

or sold by Dremel. Using attachments not

recommended may result in electric shock

or fire.

Unplug tool from power adapter when

battery in tool is fully charged. Tool left

plugged in the power adapter over a long

period of time could lead to tool damage

and fire.

Unplug power adapter from outlet before

storage, attempting any maintenance or

cleaning. Such preventive safety measures

reduce the risk of electric shock or fire.

Keep the power adapter clean by wiping it

with a damp cloth. Contamination may

result in electric shock or fire.

Replace battery pack if a substantial drop in

operating time per charge is observed.

Battery pack may be nearing the end of its life.

 Battery Care

When batteries are not

in tool, keep them away

from metal objects. For example, to protect

terminals from shorting DO NOT place

batteries in a tool box or pocket with nails,

screws, keys, etc. Fire or injury may result.

DO NOT PUT BATTERIES INTO FIRE OR

EXPOSE TO HIGH HEAT. Exposure to fire or

to temperatures above 265°F (130°C) may

cause explosion.

Battery leakage may occur under extreme

usage or temperature conditions. Avoid

contact with skin and eyes. The battery

liquid is caustic and could cause chemical

burn to tissues. If liquid comes in contact

with skin, wash quickly with soap and

water. If the liquid contacts your eyes, flush

them with water for a minimum of 10

minutes and seek medical attention.

Do not use a battery pack or tool that is

damaged or modiﬁed. Damaged or modiﬁed

batteries may exhibit unpredictable

behavior resulting in ﬁre, explosion or risk

of injury.

1600A01P55.qxp_7760-PGK 4/15/19 9:55 AM Page 8

9

 Battery Disposal

Do not attempt to

disassemble the tool or

remove any component projecting from

the tool. Fire or injury may result. Prior to

disposal, protect exposed terminals with

heavy insulating tape to prevent shorting.

 LITHIUM-ION BATTERIES

If equipped with a lithium-ion battery, the

battery must be collected, recycled or

disposed of in an environ mentally sound

manner.

“The EPA certified RBRC

Battery Recycling Seal on the

lithium-ion (Li-ion) battery

indicates Robert Bosch Tool

Corporation is voluntarily

participating in an industry

program to collect and recycle these

batteries at the end of their useful life,

when taken out of service in the United

States or Canada. The RBRC program

provides a convenient alterative to placing

used Li-ion batteries into the trash or the

munici pal waste stream, which may be

illegal in your area.

Please call 1-800-8-BATTERY for information

on Li-ion battery recycling and disposal

bans/restrictions in your area, or return

your batteries to a Bosch/Dremel Service

Center for recycling. Robert Bosch Tool

Corporation’s involvement in this program

is part of our commitment to preserving our

environment and conserving our natural

resources.”

Do not open the tool or

attempt to remove

battery from your tool. Dispose of tool

through your local waste removal authority

or a Bosch/Dremel Service Center.

Safety Rules for Charging

SAVE THESE INSTRUCTIONS

1600A01P55.qxp_7760-PGK 4/15/19 9:55 AM Page 9

10

Symbols

Important: Some of the following symbols may be used on your tool. Please study them

and learn their meaning. Proper interpretation of these symbols will allow you to operate

the tool better and safer.

Symbol Designation / Explanation

V Volts (voltage)

A Amperes (current)

Hz Hertz (frequency, cycles per second)

W Watt (power)

kg Kilograms (weight)

min Minutes (time)

s Seconds (time)

⌀ Diameter (size of drill bits, grinding wheels, etc.)

n

0

No load speed (rotational speed at no load)

n Rated speed (maximum attainable speed)

.../min

Revolutions or reciprocation per minute (revolutions, strokes, surface

speed, orbits etc. per minute)

0 Off position (zero speed, zero torque...)

1, 2, 3, ...

I, II, III,

Selector settings (speed, torque or position settings. Higher number

means greater speed)

0

Infinitely variable selector with off (speed is increasing from 0 setting)

Arrow (action in the direction of arrow)

Alternating current (type or a characteristic of current)

Direct current (type or a characteristic of current)

Alternating or direct current (type or a characteristic of current)

Class II construction (designates double insulated construction tools)

Earthing terminal (grounding terminal)

1600A01P55.qxp_7760-PGK 4/15/19 9:56 AM Page 10

11

Symbol Designation / Explanation

Alerts user to read manual

Alerts user to wear eye protection

This symbol designates that this tool is listed by Underwriters

Laboratories.

This symbol designates that this component is recognized by

Underwriters Laboratories.

This symbol designates that this tool is listed by Underwriters

Laboratories, to United States and Canadian Standards.

This symbol designates that this tool is listed by the Canadian

Standards Association.

This symbol designates that this tool is listed by the Canadian

Standards Association, to United States and Canadian Standards.

This symbol designates that this tool is listed by the Intertek Testing

Services, to United States and Canadian Standards.

This symbol designates that this tool complies to NOM Mexican

Standards.

This symbol designates that this product is verified by Underwriters

Laboratories to comply with Natural Resources Canada energy

efficiency standards.

Designates Li-ion battery recycling program

Symbols

Important: Some of the following symbols may be used on your tool. Please study them

and learn their meaning. Proper interpretation of these symbols will allow you to operate

the tool better and safer.

1600A01P55.qxp_7760-PGK 4/15/19 9:56 AM Page 11

12

1

13 14 15

2 3 4 5

7

12

8

10

9

11

6

Battery tools are always in an operative condition. Be aware of the

possible hazards.

SAVE THESE INSTRUCTIONS

Functional Description and Specifications

 Cordless Rotary Tool PawControl 7760-PGK

Model number . . . . . . . . . .7760-PGK

Voltage rating . . . . . . . . . . .3.6V / 4V Max

Rated Speed (n) . . . . . . . .8,000–25,000/min

Collet Capacities . . . . . . . .1/32", 1/16", 3/32", 1/8"

Allowed ambient temperature

– during charging . . . . . . . .32...113 °F (0...+45 °C)

– during operation/

storage . . . . . . . . . . . . . .–4...122 °F (–20...+50 °C)

Power Adapter

Model number . . . . . . . . . .510

Voltage rating . . . . . . . . . . .120V 60 Hz

Amperage rating . . . . . . . .1A

Battery

Chemistry . . . . . . . . . . . . .Li-ion

Capacity . . . . . . . . . . . . . . .2.0Ah

Charge time . . . . . . . . . . . .2 Hr 45 min.

1 Collet nut

2 Collet

3 EZ TWIST™ integrated wrench/

nose cap

4 Tool shaft

5 Insulated gripping surface

6 Ventilation Openings

7 Shaft Lock Button

8 On/Off switch and speed dial

9 Battery charge indicator

10 Micro USB port

11 Micro USB port cover

12 Threaded nose

13 USB cable

14 Power adapter*

15 Collet wrench

* Not included in all kits

1600A01P55.qxp_7760-PGK 4/15/19 9:56 AM Page 12

13

Functional Description and Specifications

 AT01-PGA Pet grooming attachment

 EZ402 EZ Lock™ Mandrel and SD60PGA Sanding disc

27

24

21

26

25

22

20

23

20 Attachment housing

21 Clear cap

22 Clasp

23 Hinge

24 Sanding disc opening

25 Tab (part of clear cap)

26 Depth guide

27 Ramp

28

29 30 31

32

33

28 EZ Lock™ mandrel EZ402

29 Blue spacer

30 Spring-loaded sleeve

31 Bow tie interface

32 Sanding disc SD60PGA

33 Bow tie interface

1600A01P55.qxp_7760-PGK 4/15/19 9:56 AM Page 13

14

Charging the Tool

Your Dremel PawControl 7760-PGK

does not come completely charged from

the factory. Be sure to charge tool prior

to initial use.

- Insert USB cable 13 into USB port of

power adapter 14 (Fig. 1). If power

adapter is not included, charge tool

using 5V/1A minimum USB power

adapter.

- Plug power adapter 14 into standard

power outlet.

- Open Micro USB port cover 11 and

plug micro USB plug into Micro USB

port 10.

The battery charge indicator 9 indicates

the charging progress. During the

charging process, the indicator will glow

green. The battery is fully charged when

the indicator light turns off. Charge time

is approximately 2 hours and 45

minutes.

It is normal for the handle of the tool to

get warm during charging.

Note: charging function stops while tool

is running and resumes again after tool

is turned off.

When the battery is fully charged,

disconnect the Micro USB end of the

cable 13 from the tool and close the

cover 11.

Unplug the power adapter from the

power outlet (unless you are charging

another tool).

 Battery Charge Indicator

This tool is equipped with a charge

indicator 9 that tells you how much

charge your battery has. When the light

is red, the battery is almost empty.

Note: Red light may also indicate that

the tool is stalling. Refer to “Electronic

Monitoring” on page 16.

When the battery is depleted, the tool

will turn off automatically. This will be a

sudden stop as opposed to a gradual

slow down of the tool. Simply recharge

the tool.

 Important Charging Notes

- Lithium-ion battery will hold its

charge while in storage for up to 2

years so it’s always ready when you

need it.

- The power adapter was designed to

fast charge the battery only when the

battery temperature is between 32˚F

(0˚C) and 113˚F (45˚C).

- A substantial drop in operating time

per charge may mean that the battery

pack is nearing the end of its life and

should be replaced. For service of

your tool, please contact Dremel at

1-800-437-3635.

- If battery does not charge properly:

a. Check for voltage at outlet by

plugging in some other electrical

device.

b. Check to see if outlet is connected

to a light switch which turns power

“off” when lights are turned off.

c. Check USB terminals for dirt.

Clean with cotton swab and alcohol if

necessary.

d. Check to see if USB cable is

properly connected to the tool and

the power adapter.

e. If you still do not get proper

charging, send tool and power

adapter to your Dremel Service

Center.

Note: Use of power adapters or battery

packs not sold by Dremel may void the

warranty.

1600A01P55.qxp_7760-PGK 4/15/19 9:56 AM Page 14

15

Assembly Instructions for pet nail grooming

 To load mandrel:

A. Unscrew and remove the nose cap 3

from the tool by twisting it counter-

clockwise until it comes off the tool

(Fig. 1).

B. To loosen the collet nut, first press

shaft lock button 7 and rotate the

collet nut 1 by hand until the lock

engages the shaft preventing further

rotation (Fig. 2).

Do not engage shaft

lock while the tool is

running.

C. With the shaft lock 7 engaged, loosen

the collet nut 1 (turn counter -

clockwise, L). Use the wrench 15 if

necessary. The collet nut must be

loosely threaded on when inserting

an accessory (Fig 2).

D. Insert EZ Lock™ mandrel 28 into

collet 2 (Fig. 2).

Make sure the blue

spacer 29 on the

mandrel bottoms out on the collet nut,

setting the mandrel to the correct

depth. Failure to set the mandrel to the

correct depth can result in damage to

the attachment.

E. With the shaft lock 7 engaged,

tighten the collet nut 1 securely (turn

clockwise, T) with wrench 15 (Fig. 2).

Note: If the EZ Lock™ mandrel does not

fit into the collet, it is possible that the

collet is stuck within the collet nut. If

this happens, remove the collet nut from

the tool by continuing to twist it

counterclockwise. If the collet does not

separate from the collet nut when

removed from the tool, push the shank

of the EZ Lock™ mandrel 28 into the

hole in the collet nut 1. This should

cause the collet 2 to pop out of the

collet nut 1. Re-assemble by placing the

collet 2 into the output shaft 4 and

twisting the collet nut 1 clockwise over

the collet to tighten it back onto the

output shaft 4 (Fig. 3).

 To load sanding disc:

A. Pull spring-loaded sleeve 30 DOWN

towards tool with one hand and hold.

You can brace the tool on the body or

workbench for extra leverage

(Fig. 4).

B. With the other hand, align bow tie

interface 31 on mandrel with metal

bow tie interface 33 on bottom of

sanding disc 32 (Fig. 4).

C. Place sanding disc on the mandrel to

a point just below the bow tie on the

mandrel 31 and twist 90 degrees

until the bow tie interface 33 on the

sanding disc 32 aligns with the sleeve

3

Fig. 1

L

T

28

15

29

2

1

7

30

31

33

32

90°

7

30

31

3332

Fig. 2

Fig. 4 Fig. 5

2

4

1

28

Fig. 3

Always be sure the tool is turned “OFF” before changing accessories,

changing collets or servicing your cordless rotary tool.

1600A01P55.qxp_7760-PGK 4/15/19 9:56 AM Page 15

16

Assembly Instructions for pet nail grooming

30. Release sleeve 30. Sanding disc

32 should lock in place (Fig. 5).

Incorrect seating of

sanding disc on

mandrel may lead to personal injury or

property damage. To check for proper

seating, hold shaft lock button 7 and

twist the sanding disc 32. The sanding

disc 32 will not be able to rotate on

mandrel.

 To unload sanding disc:

A. Pull spring-loaded sleeve 30 DOWN

toward tool with one hand (Fig. 5).

B. Hold sleeve 30 down while twisting

sanding disc 32 90 degrees (Fig. 5).

C. Remove sanding disc 32 (Fig. 5).

 To attach nail guard

attachment:

Note: Make sure that the mandrel and

the sanding disc are mounted properly

before mounting the attachment.

A. Detach the clear cap 21 from the

attachment by running the small

knobs 25 on the inside of the clear

cap up along the height adjustment

guide 26 until they reach the guided

opening (Fig. 6).

B. Unlock the clasp 22.

C. Open the attachment 20 (Fig. 6).

D. Position the attachment 20 around

the threaded nose of the tool 12 and

close the attachment together until

the clasp 22 is fully engaged (Fig. 7).

E. Turn the whole attachment 20

clockwise to screw it into place on

the threaded nose 12. Make sure that

it is securely tightened so that it will

not shift positions during use (Fig. 7).

F. Re-attach the clear cap 21 (simply

perform step A in reverse order).

G. Turn the clear cap so that the small

knobs are all the way to the end of

slot 26 (next to number “3”) on the

attachment. You will hear the cap

click into place when fully installed.

Do not force the clear cap out of the

guides (Fig. 6).

Note: Refer to the AT01-PGA manual on

the Dremel website for additional

information regarding attachment

compatibility.

B

C

A

21

26

25

20

22

Fig. 6

D

E

12

22

20

Fig. 7

1600A01P55.qxp_7760-PGK 4/15/19 9:56 AM Page 16

17

Nail Grooming Operating Instructions

Observe all warnings

and safety

instructions when using the rotary tool.

Failure to follow recommended

procedures could result in personal

injury or property damage.

 Why Use a Dremel Rotary

Tool to Groom Pet Nails?

Scissors and guillotine-type clippers

apply pressure and pinch the nail, which

can be uncomfortable for pet toes and

feet. Clipping toenails also increases

the likelihood of cutting the internal

blood supply to the nail, called the

quick; grinding is more gradual and

controlled. If the quick is nicked using a

rotary tool, the cut is usually smaller and

will heal quicker than a cut made with a

nail clipper.

 Before you start

Grooming a pet’s nails for the first time

can be a worrisome experience for both

the pet and pet owner. Rest assured

that nail grooming does not have to be a

stressful experience. By starting early

and considering grooming to be part of

your pet’s training, your pet will grow

used to the experience.

First, train your pet to feel comfortable

with their paws being touched and

handled before exposing them to the

rotary tool. One way to do this is to

massage their legs, paws, and individual

toes for a few minutes at least once a

day. Afterwards, create a positive

association with this experience by

rewarding your pet with its favorite

snack.

Next, help your pet grow gradually

accustomed to the rotary tool. Let your

pet sniff the tool while it is turned off.

Then, while keeping the tool in your

hand, let your pet listen to the sound

the tool makes when it is turned on.

Ideally, have your pet sit or lay on its

side while the tool is in your hand and

running. Gradually work up to having

your pet’s toenails touch the rotating

sanding disc for less than a second. Do

not grind the nails yet; simply let your

pet become familiar with the tool.

Throughout the acclimation process,

continue to praise your pet and reward

good behavior with a snack. This

process may take a couple of days or

weeks. Before long, both you and your

pet will be able to relax and even enjoy

the grooming time that you share

together.

 Nail Anatomy

The nails/claws containing quick vessels

described in this section are relevant to

several types of pets, including dogs

and cats.

Before trimming your pet’s nails, you

will need to identify the quick. The

diagram (Fig. 8) shows the basic

anatomy of a pet’s toenail. The outer

nail is hard and has no feeling because it

has no nerve endings. The core of the

nail is the quick. It is made up of tiny

blood vessels and nerve endings and is

very sensitive. The quick is a vein that

“feeds” the toenail. Should you cut the

quick while trimming a nail, the nail will

start to bleed.

Light colored nails are often transparent

enough to allow you to see the quick’s

pink core. Dark colored nails may not

allow you to see where the quick is

located. Pets may have both light and

dark colored nails that allow you to

estimate the length of the quick.

The diagram also shows an estimate of

the proper angle at which to trim a pet’s

nails. A rule of thumb for the proper

angle is 45 degrees upwards from the

bottom of the paw. The proper angle

may vary according to the pet owner’s

wishes or the pet’s unique anatomy.

Trim nails so that they almost touch the

ground when your pet is walking.

45°

35 3637 38 34

Fig. 8

34 Nail / Claw

35 Quick

36 Paw

37 Floor

38 Trim line

1600A01P55.qxp_7760-PGK 4/15/19 9:56 AM Page 17

18

 The Nail Grooming Process

Use only “golf grip”

or “hand grip”

method of holding the tool. Never hold

the tool by the attachment. Holding the

tool by the attachment could cause it to

unexpectedly shift, causing loss of

control (Fig.9).

Place the pet’s paw 36 on the ramp 27

so that the nail 34 is close to - but not

touching - the sanding disc 32 (Fig.10).

The tool is controlled by the blue

“On/Off” / Speed Switch 8 located on

the topside of the recessed part of the

housing (Fig. 11).

TO TURN THE TOOL “ON” gently slide

the switch 8 up with your thumb. The

tool will start working at a speed of

8,000 RPM (Position “1”).

R e c o m m e n d e d

maximum operating

speed for most pet grooming

applications is 10,000/min.

Recommended speed setting is "1".

Nail thickness and other factors may

require use of higher speeds. Use

extreme caution when operating at

higher speeds and limit the amount of

time that the nail is exposed to the

sanding surface. Use of higher

operating speeds may cause heat

buildup and injury to the pet. Always

monitor pet for signs of discomfort and

stop grooming if observed.

Support the toe and nail in one hand

while using the rotary tool in the other

hand. This is more comfortable for your

pet as it lessens vibration on the paw.

Pushing gently on the bottom of the

paw’s pad extends the nail slightly for

easier grooming.

It is important to let the speed of the

rotary tool do the work; never apply

pressure to the toenail with the spinning

sanding disc. Pressure may cause the

nail to grow too hot, resulting in

discomfort for your pet. The rotary

tool’s spinning sanding disc should not

be kept against the nail longer than

three seconds at a time. Instead of

focusing on completing one nail at a

time, it is recommended to briefly trim

each nail on one paw, and then the

other, in several passes. This allows

time for the nails to cool. You may

repeat this process as needed. Trim

nails so that they almost touch the

ground when your pet is walking.

Turn the tool off by sliding the tool

switch 8 to “0” position (Fig. 11).

 Pet Safety Tips

Some pets may become nervous in the

presence of the tool so it is best to

secure your pet. The operator will need

both hands to groom the nails so it may

be helpful to have another person assist

in restraining your pet.

If hair is accidentally caught in the

rotary tool, immediately turn off the tool

and untangle the hair from the tool. For

pets with particularly long hair, use an

old sock to cover the toe, foot, and leg

of the pet and isolate the nail. Push the

nail out through a small opening at the

tip of the sock to groom the nail. Keep

styptic powder on hand in case of

bleeding. Styptic powder is available at

7 8

Nail Grooming Operating Instructions

3432

3627

Fig. 9

Fig. 10

Fig. 11

1600A01P55.qxp_7760-PGK 4/15/19 9:56 AM Page 18

19

Nail Grooming Operating Instructions

most pet supply stores. Follow the

directions on the packaging for proper

use instructions.

 Cleaning the Pet Grooming

Attachment

Remove the pet grooming attachment

from the rotary tool as needed to clean

out any nail dust or debris. Wash only

the attachment with warm water and

dry thoroughly with a clean cloth before

reinstalling on rotary tool.

PawControl 7760-PGK can also be used

with a variety of Dremel accessories that

will turn this tool into a carver, a

grinder, polisher, sander, cutter, power

brush, drill and more.

First, reverse the assembly steps on

pages 15 and 16 to remove pet

grooming attachment, EZ Lock™

mandrel and reinstall the nose cap.

 Collets

Dremel accessories such as engraver

bits, grinding stones and mandrels are

mounted on the tool using collet and

collet nut system.

PawControl 7760-PGK comes with the

1/8” collet No 480. There are also three

other collets to accomodate smaller

diameter accessories. Identification (ID)

rings will help you choose the right

collet for your bits (Fig. 12).

Assembly Instructions for applications

other than pet nail grooming

Always be sure the tool is turned “OFF” before changing accessories,

changing collets or servicing your cordless rotary tool.

2a 2b 2c 2d 2e1

4

Fig. 12

1 Collet nut

2a 1/8” collet 480 - no ID rings

2b 3/32” Collet 481 - three ID rings

2c 1/16” Collet 482 - two ID rings

2d 1/32” Collet 483 - one ID ring

2e ID ring

1600A01P55.qxp_7760-PGK 4/15/19 9:56 AM Page 19

20

Assembly Instructions for applications

other than pet nail grooming

To loosen collet nut 1, first press shaft

lock button 7 and rotate the collet nut

counterclockwise (L) by hand until the

lock engages the shaft preventing

further rotation (Fig. 13).

Do not engage shaft

lock while the Rotary

Tool is running.

With the shaft lock 7 engaged, use the

EZ TWIST™ integrated wrench / nose cap

3 or collet wrench 15 to loosen (turn

counterclockwise, L) the collet nut 1

(Fig. 13). The collet nut must be loosely

threaded on when inserting an

accessory.

Change accessories by inserting the new

one into the collet as far as possible to

minimize runout and unbalance. With

the shaft lock 7 engaged, tighten the

collet nut 1 securely (turn clockwise, T)

with wrench 15 or EZ TWIST™ integrated

wrench/ nose cap 3 (Fig. 13). Avoid

excessive tightening of the collet nut

when there is no bit inserted.

Always use the collet

which matches the

shank size of the accessory you plan to

use. Never force a larger diameter shank

into a collet.

To install a different collet, completely

unscrew the collet nut 1 and remove the

old collet 2. Insert the unslotted end of

the collet in the hole in the end of the

tool shaft 4. Replace collet nut on the

shaft (Fig. 12).

Note: Most rotary tool kits do not

include all four collets sizes.

 FIXING STUCK COLLETS

It is possible for a collet to get stuck

within the collet nut especially if a collet

nut is tightened onto the tool without a

bit in place. If this happens, remove the

collet nut from the tool by continuing to

twist it counterclockwise. If the collet

does not separate from the collet nut

when removed from the tool, push the

shank of the EZ Lock™ mandrel 28 into

the hole in the collet nut 1. This should

cause the collet 2 to pop out of the

collet nut 1. Re-assemble by placing the

collet 2 into the output shaft 4 and

twisting the collet nut 1 clockwise over

the collet to tighten it back onto the

output shaft 4 (Fig. 3).

 Balancing Accessories

For precision work, it is important that

all accessories be in good balance

(much the same as the tires on your

automobile). To true up or balance an

accessory, slightly loosen collet nut and

give the accessory or collet a 1/4 turn.

Re tighten collet nut and run the Rotary

Tool. You should be able to tell by the

sound and feel if your accessory is

running in balance. Continue adjusting

in this fashion until best balance is

achieved. To maintain balance on

abrasive wheel points, before each use,

with the wheel point secured in the

collet, turn on the Rotary Tool and run

the 415 Dressing Stone lightly against

the revolving wheel point. This removes

high spots and trues up the wheel point

for good balance.

7

3

L

T

15

28

1

Fig. 13

1600A01P55.qxp_7760-PGK 4/15/19 9:56 AM Page 20

La page charge ...

Dremel PawControl 7760-PGK Operating/Safety Instructions Manual

Dremel PawControl 7760-PGK Operating/Safety Instructions Manual

dans d''autres langues

Documents connexes

Autres documents