NORCOLD, Inc.
P.O. Box 4248
Sidney, OH 45365-4248
Part No. 635494C (10/22/2014)
English
Owner’s Manual
for the 121X series of RV Refrigerators
The letter “X”, in the model numbers above, stands for a letter or numeral which means a
refrigerator option.
FIRE OR EXPLOSION HAZARD
If you smell gas:
1. Open Windows
2. Do not attempt to light appliance.
3. Do not touch electrical switches.
4. Extinguish any open ame
5. Shut off fuel supply.
6. Evacuate immediately and call emergency services.
Failure to follow these instructions could result in re or explosion, which could cause
property damage, personal injury, or death.
Improper installation, adjustment, alteration, service or maintenance
can cause injury or property damage. Refer to this manual. For
assistance or additional information, contact a qualied installer,
service agency, or the gas supplier.
FOR YOUR SAFETY
Do not store or use gasoline or other ammable vapors and liquid in the
vicinity of this or any other appliance.
WARNING
!
WARNING
!
Norcold Customer Support Dept.
Telephone: 800-543-1219
Fax: 734-769-2332
Web Site: www.norcold.com
Owner’s Manual 2
Table of Contents
For dened warranty terms, please see the one page warranty statement included in the product information packet.
Safety Awareness ........................................................................................................................................................................................ 3
Safety Instructions ....................................................................................................................................................................................... 3
About Your Refrigerator ............................................................................................................................................................................... 3
Storage volume .................................................................................................................................................................................... 3
Leveling ................................................................................................................................................................................................ 3
Operation during travel ......................................................................................................................................................................... 3
Food compartment ............................................................................................................................................................................... 3
Freezer compartments ......................................................................................................................................................................... 4
Door handles ........................................................................................................................................................................................ 4
Moveable door seal .............................................................................................................................................................................. 4
Crispers ................................................................................................................................................................................................ 4
Tall bottle and gallon storage drawer.................................................................................................................................................... 5
Door bins .............................................................................................................................................................................................. 5
Adjustable shelves ............................................................................................................................................................................... 5
Interior light........................................................................................................................................................................................... 5
Door alarm ........................................................................................................................................................................................... 6
Moisture reduction heater..................................................................................................................................................................... 6
Temperature control system ................................................................................................................................................................. 6
Backup operating system ..................................................................................................................................................................... 6
Temperature switch monitor ................................................................................................................................................................. 7
Operating the Refrigerator Controls ............................................................................................................................................................ 7
Control panel ............................................................................................................................................................................................... 7
Automatic mode operation ................................................................................................................................................................... 8
Removing air from the propane gas supply lines ................................................................................................................................. 8
Set the controls to automatic mode operation ...................................................................................................................................... 9
Set the controls to manual mode operation.......................................................................................................................................... 9
Effects of High Altitude on Propane Gas Operation .................................................................................................................................. 10
Effects of Freezing Temperatures on Refrigerator Operation .................................................................................................................... 12
Ice Maker (Optional) .................................................................................................................................................................................. 10
Ice maker operation............................................................................................................................................................................ 10
Refrigerator Care Checklist ........................................................................................................................................................................11
Defrosting ...................................................................................................................................................................................................11
Cleaning .................................................................................................................................................................................................... 12
Interior ................................................................................................................................................................................................ 12
Drip tray .............................................................................................................................................................................................. 12
Metal doors......................................................................................................................................................................................... 13
Door Sealing .............................................................................................................................................................................................. 13
Refrigerator Storage .................................................................................................................................................................................. 13
Refrigerator Maintenance Checklist ......................................................................................................................................................... 14
Ice Maker Storage (Optional) .................................................................................................................................................................... 14
Refrigerator Maintenance .......................................................................................................................................................................... 15
Gas ame appearance ....................................................................................................................................................................... 15
Remove and clean the burner orice ................................................................................................................................................. 16
Remove the Refrigerator ........................................................................................................................................................................... 16
Reinstall the Refrigerator ........................................................................................................................................................................... 17
Replacement Parts .................................................................................................................................................................................... 18
Fault Codes ............................................................................................................................................................................................... 18
Wiring Diagram and Pictorial ..................................................................................................................................................................... 19
Ice Maker Wiring Pictorial and Diagram (Optional) ................................................................................................................................... 20
Wiring Diagram and Pictorial - Low Ambient Heater (optional) ................................................................................................................. 21
Owner’s Manual 3
Safety Instructions
Safety Awareness
Read this manual carefully and understand the contents before you use the refrigerator.
Be aware of possible safety hazards when you see the safety alert symbol on the refrigerator and in this manual. A signal word follows
the safety alert symbol and identies the danger of the hazard. Carefully read the descriptions of these signal words to fully know their
meanings. They are for your safety.
This signal word means a hazard, which if ignored, can cause dangerous personal injury, death, or much
property damage.
This signal word means a hazard, which if ignored, can cause small personal injury or much property
damage.
- The storage of ammable materials behind or around the refrigerator creates a re hazard. Do not use the area
behind the refrigerator to store anything, especially ammable materials (gasoline, cleaning supplies, etc.)
- Do not remove the round ground prong from the AC power cord of the refrigerator or the ice maker (optional). Do not
use a two prong adapter or an extension cord with either AC power cord.
- A circuit overload can result in an electrical re if the wires and/or fuses are not the correct size. Use only the wire
and fuse sizes as writtten in the “Installation Manual”.
- Incorrect installation, adjustment, change to, or maintenance of this refrigerator can cause personal injury, property
damage, or both. Have service and maintenance work done by your dealer or by an Norcold authorized service
center.
- Disconnect both the AC and DC power sources before doing any maintenance work on the refrigerator. All service
work on this refrigerator must be done by a qualied service technician.
- Do not bypass or change the refrigerator’s electrical components or features.
- When you discard an appliance, remove all doors to prevent accidental entrapment and suffocation.
- Do not spray liquids near electrical outlets, connections, or the refrigerator components. Many liquids are electrically
conductive and can cause a shock hazard, electrical shorts, and in some cases re.
- The refrigerator cooling system is under pressure. Do not try to repair or to recharge a defective cooling system. The
cooling system contains sodium chromate. The breathing of certain chromium compounds can cause cancer. The
cooling system contents can cause severe skin and eye burns, and can ignite and burn with an intense ame. Do not
bend, drop, weld, move, drill, puncture, or hit the cooling system.
- At regular intervals, make sure that the refrigerator ue the burner, the vent areas, and the ventilation air pathway
between the vents are completely free from any ammable material or blockage. After a period of storage, it is
especially important to check these areas for any ammable material or blockage caused by animals.
- The rear of the refrigerator has sharp edges and corners. To prevent cuts or abrasions when working on the
refrigerator, be careful and wear cut resistant gloves.
WARNING
!
WARNING
!
CAUTION
!
CAUTION
!
Owner’s Manual 4
About Your Refrigerator
Storage Volume:
This refrigerator is made for storage of foods and frozen food and for making ice.
Total capacity 12.0 cubic feet
Freezer Compartments 3.6 cubic feet total
Fresh Food Compartment 8.4 cubic feet
Leveling:
The refrigerator is made to operate within 3° off level side-to-side and 6° off level front-to-back (as looking at
the front of the refrigerator). Operating it at more than these limits can cause damage to the cooling system
and create a risk of personal injury or property damage. Make sure the vehicle is level before you operate
the refrigerator.
Operation during travel:
While the refrigerator should be level when the vehicle is stopped, performance during travel is not usually effected.
Food compartment:
Start up the refrigerator (see “Operating the Refrigerator Controls”)and let it cool for eight hours before loading with food. If the
refrigerator does not start to cool down after about two hours, contact your dealer or a Norcold authorized service center.
For the best cooling performance:
- Let air move freely inside the entire food compartment.
- Do not cover the shelves with plastic, paper, etc.
To decrease the amount of ice that collects on the cooling ns:
- Cover all liquids and moist foods.
- Let all hot foods cool before putting them in the refrigerator.
- Do not open the door any longer than necessary.
Freezer compartments:
The freezer compartments are made to keep pre-frozen food frozen and not to quick freeze
food.
Do not put other items on the ice tray while the water is freezing. The water
freezes more rapidly if the thermostat is at the COLDEST position.
Door handles:
During travel, the door latch prevents the door from opening. When closing each door,
push the door toward the refrigerator until you hear a “click” sound.
To open each door, pull the handle away from the refrigerator (See Art00990).
During storage, the storage latch prevents the door from completely closing. Use it to
prevent odors when the refrigerator is stored for an extended period of time.
To operate the storage latch (see Art00991), open each door about 1/2 inch, hold the door
handle in the open position, and push the storage latch [55] into the cutout [56] of the strike
plate. Do not use the storage latch as a travel latch because the doors will not be fully
closed.
Art00990
Art00991
55
56
CAUTION
!
NOTICE
Owner’s Manual 5
Movable door seal:
The movable door seal [134] is located on the left door of the fresh food compartment (See Art01789). It
provides the correct seal when both doors of the fresh food compartment are closed. When the left door of
the fresh food compartment opens, the movable door seal moves so that it is at against the edge of the
door. To avoid possible damage to the movable door seal, make sure that it is at against the edge of the
door before you close the door
Crispers:
The crispers are located at the bottom left side of the fresh food compartment and supply a storage area
to preserve fruit and vegetable freshness. Make sure that you always push the crispers fully in. The glass
crisper covers are made so that you can remove them.
Do not wash the crispers in a dishwasher. The crispers are not dishwasher safe.
To remove the glass crisper covers [135] (See Art01790):
- Remove the crispers [136].
- Remove the screw from the top right side of the crisper support wall [137].
- Remove the screws [41] from the retainer [54] on the left side of the refrigerator
(See Art00992).
- Remove the retainer.
- Remove the glass crisper covers.
- Remove the crisper support wall.
Tall bottle and gallon storage drawer:
The tall bottle and gallon storage drawer [138] is located at the bottom right side of the
fresh food compartment and supplies a storage area for items such as 2-liter bottles
or gallon milk containers (See Art01790). This drawer has a divider which prevents
items from moving and/or overturning while the vehicle is in transit. Make sure that you
always push the drawer fully in.
The divider ts down into grooves on the inside of the drawer. The divider also ts at the rear of the
drawer so that you can use all of the capacity of the drawer.
Do not wash the drawer or divider in a dishwasher. The drawer and divider are not
dishwasher safe.
Door bins:
You may put the door bins [52] of the freezer and fresh food compartment in a location that best
meets your needs (See Art01798). To remove the bins, lift them over the locator and pull them
forward. To install the bins, push them onto the locator.
Do not wash the door bins in a dishwasher. The door bins are not dishwasher safe.
Art01789
134
Art01790
137136
135
138
52
Art01798
NOTICE
NOTICE
NOTICE
Owner’s Manual 6
Adjustable shelves:
The shelves in the freezer and the fresh food compartment are made so you can remove them or
move them.
To remove or move the shelf of the freezer:
- Pull the shelf forward out of the slot.
- Push it fully into the slot that you wish.
To remove or move the shelves of the fresh food compartment:
- Remove the screws [41] from each retainer [54] on the side of the refrigerator (See Art00992).
- Remove both retainers.
- Pull each shelf forward out of the slot.
- Push each fully into the slot that you wish.
- Install both retainers with the screws.
Interior light:
The interior light is at the top of the fresh food compartment. It comes on when the
refrigerator is ON and the door is open. To replace the bulb:
1. Remove the DC power supply wires from the power board at the rear of the refrigerator.
2. Remove the cover [57] by pulling it toward the front of the refrigerator (See Art00988).
3. Remove the light bulb [58] from the holder [59].
Use only a GE#214-2 bulb as the replacement bulb. This bulb is available
at most retail automotive parts centers.
4. Install the replacement bulb.
5. Install the cover.
6. Connect the DC power supply wires to the power board at the rear of the refrigerator.
Door alarm:
The refrigerator has an alarm to alert you if the fresh food compartment door is not closed. The refrigerator continues to operate, but if
the fresh food compartment door is open and the interior light remains on for two minutes:
- An audible alarm starts.
- “dr” appears in the center display.
- The interior light automatically turns off.
Close the door to silence the alarm.
Moisture reduction heaters:
The refrigerator has heaters that prevent moisture from forming on the center divider between the two doors of the freezer compartment
and on the movable door seal. The heaters operate only when the refrigerator is ON and the DC power is sufcient. The heater in the
movable door seal also only operates when the left door of the fresh food compartment is closed.
Art00988
57
58
59
Art00992
54
41
NOTICE
Owner’s Manual 7
Temperature control system:
Although the refrigerator is not frost -free, it is made to limit frost on the cooling ns. At regular intervals, the temperature control system
automatically melts most of the frost from the cooling ns. The water from the cooling ns drains into a collection cup that is attached
to the back of the refrigerator. The heat of the cooling system evaporates the water from the collection cup.
Backup operating system:
This refrigerator has a backup operating system. The backup operating system allows the refrigerator to continue to cool if the
temperature sensor of the refrigerator should fail.
If this failure occurs:
- The refrigerator automatically changes to the backup operating system.
- When you push the SET TEMP button, the temperature setting ashes in the center display for ten seconds.
- After the temperature setting ashes, the mode of operation appears in the center display.
- The backup operating system can overfreeze or thaw the contents of the freezer and the fresh food compartment.
- Make sure the temperatures of the freezer and the fresh food compartment are satisfactory.
If you open the door(s) too often, the temperatures inside the freezer and fresh food compartment do not become
stable. Allow the refrigerator to operate for about one hour after each adjustment change before you examine the
contents. The number “9” is the coldest temperature setting.
- If the temperature is too warm, push and hold the SET TEMP button to raise the temperature setting by one number.
- If the temperature is too cold, push and hold the SET TEMP button to lower
the temperature setting by one number.
- Have the refrigerator serviced by your dealer or a Norcold authorized Service Center
as soon as possible.
Temperature switch monitor:
The refrigerator is equipped with a temperature switch [142] for overheating protection
(See Art02243) . A Norcold authorized service technician can determine if this switch has
been triggered.
142
Art02243
Operating the Refrigerator Controls
AC Operation 120 volts AC (108 volts min.-132 volts max.)
Propane gas operation: Propane gas (11 inches water column pressure)
12 volts DC - control voltage (10.5 volts min. - 15.4 volts max.)
The refrigerator operates on these energy sources. Operation out of these limits can damage the refrigerator electrical components
and will void the warranty.
Control panel:
The refrigerator control panel (See Art01333) is between the freezer compartment and the fresh food compartment. To maintain the
operating control functions of the refrigerator, a 12 volt DC power supply is necessary. The refrigerator receives DC power from the 12
volt system of the vehicle; either an auxillary battery, a converter, or the vehicle engine battery.
NOTICE
Owner’s Manual 8
The ON / OFF button [30] starts and shuts down the
refrigerator:
- To turn on the refrigerator, push and release the
ON / OFF button.
- To turn off the refrigerator, push the ON / OFF
button for one second and then release.
The SET TEMP button [32] controls the
temperature adjustment of the freezer and the fresh
food compartment. The temperature adjustment
that you select does not change if the operation
mode of the refrigerator changes.
- Push the SET TEMP button and the temperature setting (the numbers “1-9”) show in the center display [33].
- The number “9” is the coldest temperature setting.
- Push and hold the SET TEMP button and the temperature setting changes.
- Release the SET TEMP button when the temperature setting that you wish appears.
- After ten seconds, the temperature setting will go out and only a green power ON light remains.
The MODE button [31] controls the operation mode of the refrigerator:
- Push and hold the MODE button and each of the operating modes of the refrigerator show one at a time in the center display.
- There is one automatic mode of operation and two manual modes of operation.
- When the mode of operation that you wish shows in the center display, release the MODE button.
If you should forget in what mode your refrigerator is operating, push and release the MODE button to show the
current mode of operation in the center display for 10 seconds.
Automatic mode operation:
When the refrigerator is in AUTO mode, it automatically uses the most efcient energy source that is available for operation. During
operation, if a more efcient energy source becomes available, the refrigerator controls change from the current energy source to the
more efcient energy source as follows:
- The rst choice is AC operation if 120 volts AC is available to the refrigerator.
- The second choice is propane gas operation if 120 volts AC is not available to the refrigerator.
Removing air from the propane gas supply lines:
For safety reasons, the burner is made to ignite on propane gas within a specied amount of time. When starting the refrigerator for
the rst time, after storage, or after replacing propane gas tank, the propane gas supply lines can have air in them. Due to the air in the
gas supply lines, the burner may not ignite on propane gas within the specied amount of time.
To remove the air from the propane gas supply lines:
- Make sure that valve of the propane gas tanks(s) is open.
- Push the ON / OFF button to turn the refrigerator on.
- Push and hold the MODE button until the letters “LP” show in the center display.
- This means that the refrigerator is operating on propane gas.
1 COLD-9 COLDEST SET TEMP MODE ON / OFF
on
30
32
33
Art01333
31
NOTICE
Owner’s Manual 9
- If the air in the propane gas supply lines prevents the burner from ignition on propane gas, the fault codes “no” and then “FL”
will appear in the center display and you will hear an alarm sound.
- Push and hold the ON / OFF button for one second and then release to silence the alarm.
- Push the ON / OFF button to turn the refrigerator on.
- The refrigerator will start a 30 second trial for ignition.
- During the 30 second trial for ignition, the refrigerator controls open the gas safety valve and the igniter makes sparks.
- When no fault code shows and only the power indicator remains, this means that the refrigerator is operating on propane gas in the
manual mode.
- At this time, all of the air is removed from the propane gas supply lines and you may select AUTO mode of operation if you
wish.
- Depending on how much air may be in the propane gas supply lines, you may need to repeat the 30 second trial for ignition two or
three times.
- If the burner does not ignite on propane gas after two or three attempts, stop and consult your local dealer or an authorized
Norcold Service Center.
Set the controls to automatic mode operation:
- Push the ON / OFF button to turn the refrigerator on.
- Push and hold the MODE button until the letters “AU” show in the center display and then release.
- If 120 volts AC is available to the refrigerator:
- The letters “AU” and then “AC” show in the center display.
- After ten seconds, the “AU” and then “AC” go off and only a green power ON light remains.
- This means that the refrigerator is operating on AC electric.
- If 120 volts AC is not available to the refrigerator:
- The letters “AU” and then “AC” show in the center display.
- After ve seconds, the “AU” and then “LP” show in the center display.
- After ten seconds, the “AU” and the “LP” go off and only a green power ON light remains.
- This means that the refrigerator is operating on propane gas.
- If neither 120 volts AC nor propane gas is available to the refrigerator:
- The fault codes “no” “AC” and then “no” “FL” show in the center display and an audible alarm sounds.
If an energy source is available to the refrigerator, but is not operating correctly:
- A fault code shows in the center display.
- The refrigerator controls try to change to a less efcient energy source.
- If a less efcient energy source is not available:
- An audible alarm starts.
Owner’s Manual 10
- A fault code shows in the center display.
- Refer to the “Fault Codes” section of this manual.
Set the controls to manual mode operation:
- Push the ON / OFF button to turn the refrigerator on.
- Push and hold the MODE button until the letters “ AC” show in the center display and then release.
- After ten seconds, the “AC” goes off and only a green power ON light remains.
- Push and hold the MODE button until the letters “LP” show in the center display and then release.
- After ten seconds, the “LP” goes off and only a green power ON light remains.
Ice Maker (Optional)
Effects of High Altitude on Propane Gas Operation
When you operate the refrigerator on propane gas at altitudes higher than 5500 feet above sea level:
- You may experience reduced cooling performance of the refrigerator.
- You may experience burner outages.
To avoid these possible problems, Norcold recommends that you operate the refrigerator on AC when at altitudes higher than 5500 feet
above sea level.
Effects of Freezing Temperatures on Refrigerator Operation
A gas absorption refrigerator is not designed to operate in freezing temperatures. If the refrigerator is not equipped for low temperature
operation, and if the cooling system of the refrigerator is exposed to temperatures of 32° F. or lower for an extended period of time,
the refrigerator operation may be disrupted. The refrigerator operation will resume when the cooling system of the refrigerator warms
sufciently.
If the refrigerator is equipped for low temperature operation, the refrigerator will operate in temperatures down to 0° F.
Disrupted operation of the refrigerator, due to extended exposure to temperatures of 32° F. or lower, and any costs incurred to warm the
cooling system of the refrigerator are not covered by the Norcold limited warranty. Please contact your local RV dealer for information
about how to resume refrigerator operation or about how to equip your refrigerator for operation in freezing temperatures.
Do not change the installation or the venting of your refrigerator. Refrigerator failures, which are the result of changes to either the
refrigerator installation or to the venting, are not covered by the Norcold limited warranty.
The ice maker is assembled to the refrigerators at the factory as optional equipment. If the refrigerator does not have a factory installed
ice maker, one cannot be added to the refrigerator at a later time.
The ice maker is fully automatic and will operate in ambient temperatures as low as 0° F. To allow operation at temperatures between
0° F and 32° F., the ice maker has a heater on the solenoid water valve and on the water line between the solenoid valve and the ice
maker. At temperatures below 0° F, store the ice maker as written in the “Ice Maker Storage” section of this manual.
The water line heater does not protect the water supply line from the vehicle shut off valve to the solenoid
valve on the back of the refrigerator.
CAUTION
!
Owner’s Manual 11
When the freezer temperature of the refrigerator is low enough, the ice maker opens the water solenoid valve and lls the mold. The
ice maker ejects the frozen ice into a storage bin. As the storage bin lls, the ice raises the shut-off arm until it turns off the ice maker.
As you use the ice and lower the ice level in the storage bin, the shut-off arm also lowers. This turns the ice maker ON and begins the
process of making ice.
The ice maker operates on:
- Cold potable water at a pressure of 15 psi - 125 psi.
- 120 Volts AC (108 VAC min. - 132 VAC max.).
Ice maker operation:
1. Make sure the ice maker AC power cord is plugged into a receptacle.
2. Open the water shut off valve of the vehicle.
Make sure that the ice maker arm can move freely and does not touch the frozen
foods in the freezer.
3. Push the ice maker arm down to the ON position [60] (See Art01015).
If you operate the refrigerator without connecting the water supply line and/or
opening the water shut off valve of the vehicle, make sure the ice maker arm
is up in the OFF position.
4. Allow the freezer to cool enough and ice production will begin to ll the storage bin [61].
New plumbing connections and/or impurities in the water supply line after winterizing
can cause the rst ice to be discolored or have an odd avor.
5. To stop the ice maker, push the ice maker arm up to the OFF position [62].
Art01015
60
62
61
Refrigerator Care Checklist
Your refrigerator will give you years of trouble free service if you do these simple checks every three to six months:
- Keep the food compartment and the freezer clean. See “Cleaning”.
- Defrost the refrigerator as necessary. See “Defrosting”.
- Make sure the door seals correctly. See “Door Sealing“.
- Be aware of any cooling changes that are not because of weather, loading, or gas control changes. If changes occur, contact your
dealer or service center.
- Make sure the gas supply is propane gas only and not butane or a butane mixture.
- When in propane gas operation, examine the appearance of the ame. See “Gas Flame Appearance”.
- Make sure the air ow in the lower intake vent, through the refrigerator coils and condenser, and out the upper exhaust vent is not
blocked or decreased.
- Make sure the area behind the refrigerator is clear. Do not use the area behind the refrigerator for storage of anything, especially
combustible materials, especially gasoline and other ammable vapors and liquids.
NOTICE
NOTICE
CAUTION
!
Owner’s Manual 12
Defrosting
The cooling ns of the refrigerator operate at below freezing temperature and will naturally form frost from humidity, which is always
present in the air. The humidity inside the refrigerator increases:
- with higher outside temperature and humidity.
- with the storage of non-sealed fresh foods or warm foods.
- with the amount of time that the door(s) are open.
- with any air leakage into the refrigerator.
Although the refrigerator is not frost -free, it is made to limit frost on the cooling ns. At regular intervals, the temperature control system
automatically melts most of the frost from the cooling ns. The water from the cooling ns drains into a collection cup that is attached to
the back of the refrigerator. The heat of the cooling system evaporates the water from the collection cup.
It is normal for frost to collect inside the freezer. Excess frost decreases the cooling performance of the refrigerator. Defrost the
refrigerator and freezer as necessary:
- Remove all food from the refrigerator.
- Turn the refrigerator OFF.
Defrosting the refrigerator makes excess water inside the refrigerator.
- Remove the drain hose from the drip cup at the rear of the refrigerator.
- Put the drain hose into a half-gallon or larger container to capture water.
- Put dry towels (etc.) inside the refrigerator and freezer to absorb melted frost.
High temperatures can cause the inside surfaces of the refrigerator to warp or melt. Do not use pans of
HOT water, a hair dryer, or any other high temperature devices to defrost the refrigerator. Do not use any
hard or sharp objects to remove frost. Damage to the interior of the refrigerator can occur.
- To increase the speed of defrosting, put pans of WARM water in the refrigerator and freezer.
- Remove the wet towels (etc.) and dry the interior.
- Remove the drain hose from the large container and put the drain hose back into the drip cup.
- Remove the large container from the enclosure.
- Start up the refrigerator.
- Allow the refrigerator to cool down.
- Return all food to the refrigerator.
NOTICE
CAUTION
!
Owner’s Manual 13
Interior:
A good time to clean the refrigerator is just after you defrost it. Clean the inside of the refrigerator as often as necessary to avoid food
odors:
- Remove all food from the refrigerator.
Do not use abrasive cleaners, chemicals, or scouring pads because they can damage the interior of the refrigerator.
- Wash the interior with a mild cleaner or a solution of liquid dish detergent and warm water.
- Rinse with a solution of baking soda and clean water.
- Dry with clean cloth.
- Put all food in the refrigerator.
Drip tray:
To remove and clean the drip tray:
- Remove the screws [41] from the retainers [54] on each side of the refrigerator (See Art00992).
- Remove the retainers.
- Pull the self that is in front of the drip tray forward to remove from the refrigerator
- Make sure that the drip tray is empty of water.
- Pull the drip tray out of the drain hose.
- Pull the drip tray forward to remove from the slots in the refrigerator cabinet.
- Clean the drip tray.
- Push the drip tray back into the slots in the refrigerator cabinet.
- Push the drip tray back into the drain hose.
- Put the wire shelf back in the original position.
- Install the retainers with the screws.
Metal doors:
To clean the metal doors:
- Wash the doors with a mild cleaner or a solution of liquid dish detergent and warm water.
- Rinse with clean water.
- Dry with clean cloth.
Do not use abrasive cleaners, chemicals, or scouring pads because they can damage the metal doors.
Cleaning
NOTICE
NOTICE
Owner’s Manual 14
Door Sealing
Check the seal of the doors (See Art00980).
If either door does not seal correctly, excess frost will collect inside the refrigerator. Make sure the doors seal correctly:
- Close each door on a piece of paper that is about the size and thickness of a dollar bill.
- Gently pull the paper.
- You should feel a slight drag between the gasket and the cabinet.
- Do this on all four sides of the door.
- If you do not feel a slight drag on the paper, the door does not seal correctly.
- Have your dealer or an authorized Norcold Service Center correct the seal of the door.
Refrigerator Storage
Before the refrigerator is stored for an extended (seasonal) period of time:
- Defrost and clean the interior of the refrigerator.
- Close the doors with the storage latch.
If the refrigerator is stored for an extended period of time, before start up:
- Make sure there are no obstructions in the vents, the ventilation air pathway, the burner, the orice, or the ue area.
Art00980
Refrigerator Maintenance Checklist
Read and understand the following maintenance sections of this manual.
Norcold is not responsible for installation, adjustment, alteration, service, or maintenance performed by anyone other
than a qualied RV dealer or a Norcold authorized service center.
Have a qualied RV dealer or a Norcold authorized service center do these annual safety and maintenance checks:
- Examine the gas supply lines for leaks.
- Replace or repair if needed.
- Make sure the propane gas pressure is 11 inches water column.
- Adjust if needed.
- Make sure the combustion seal is complete and intact.
- Replace or repair it if needed.
- Make sure the burner and the burner orice are clean.
- Clean if needed.
NOTICE
Owner’s Manual 15
Ice Maker Storage (Optional)
To prepare the ice maker for seasonal storage:
1. Close the vehicle water supply valve to the ice maker.
2. Push the ice maker arm up until it locks into the OFF position.
3. Remove the garden hose adapter from the water solenoid valve.
4. Remove the ice maker water line from the water solenoid valve
- Do not unwrap the water line heater wires from around the water solenoid valve.
5. Drain all of the water from both the water supply line and the ice maker water line.
6. Put the end of the water supply line, the end of the ice maker water line, and the water solenoid valve each into a clean plastic bag.
7. Use tape to close each plastic bag around the water lines and the water solenoid valve.
To use the ice maker after seasonal storage:
Do not operate the ice maker when the ambient air temperature is 0° F. or lower. Damage to the water
solenoid valve and the water supply line can occur.
1. Remove the tape and plastic bags from the end of the water supply line, the end of the ice maker water line, and the water solenoid
valve.
2. Connect the ice maker water line to the water solenoid valve.
3. Connect the garden hose adapter to the water solenoid valve.
4. Push the ice maker arm down into the ON position.
5. Open the vehicle water supply valve to the ice maker.
You should discard and not use the rst two batches of ice cubes. It will take about three cycles for the ice maker to
make fully formed and clean ice cubes.
- Make sure the electrode is clean and the spark gap is 1/8 - 3/16 inch.
- Adjust if needed.
- Make sure the AC voltage is 108 -132 volts and the DC voltage is 10.5 - 15.4 volts.
Refrigerator Maintenance
Gas ame appearance:
While in LP GAS operation, examine the appearance of the gas ame:
- Push the TEMP SET button until the number “9” appears in the center display.
- Open the lower intake vent.
The burner box cover can be hot. Wear gloves to avoid burns.
CAUTION
!
CAUTION
!
NOTICE
Owner’s Manual 16
- Look at the gas ame [75] (See Art02244).
- The ame should be:
- a darker blue color on the inside of the ame and a lighter blue color on the
outside of the ame.
- a constant shape without ickering.
- Contact your dealer or Norcold authorized service center if the ame is:
- yellow
- ickering or changing shape.
- Make sure the ame does not touch the inside of the ue tube [76].
- If the ame touches the inside of the ue tube, contact your dealer or Norcold authorized service center.
- Close the burner box door.
Remove and clean the burner orice:
Your dealer or Norcold authorized service center must do this procedure.
Remove and clean the burner orice (See Art00956):
- Close the valve at the propane gas tank(s).
- Push the ON / OFF button to shut down the refrigerator.
- Open the lower intake vent.
The burner box cover can be hot. Wear gloves to avoid burns.
- Remove the burner box cover by removing the screw(s).
To avoid possible propane gas leaks, always use two wrenches to loosen and tighten the gas supply line
connections.
- Remove the are nut from the orice assembly [77] (See Art00956).
- Remove the orice assembly from the burner [78].
Do not try to remove the orice [79] from the orice adapter [80] when cleaning. Removal will damage
the orice and seal of the orice and can cause a propane gas leak. Leaking propane gas can ignite or
explode which can result in dangerous personal injury or death. Do not clean the orice with a pin or
other objects.
- Clean the orice assembly with air pressure and alcohol only.
- Using a wrench, assemble the orice assembly to the burner.
- Assemble the are nut to the orice assembly.
- Examine all of the connections for gas leaks.
- Assemble the burner box cover.
76
75
Art02244
Art 00956
77
78
79
80
CAUTION
!
WARNING
!
WARNING
!
Owner’s Manual 17
Remove the Refrigerator
Your dealer or Norcold authorized service center must do this procedure.
The rear of the refrigerator has sharp edges and corners. To prevent cuts or abrasions when working on the
refrigerator, be careful and wear cut resistant gloves.
To avoid possible propane gas leaks, always use two wrenches to loosen and tighten the gas supply line
connections.
1. Close the valve at the propane gas tank(s).
2. Remove the black AC power cord and the white ice maker AC power cord (optional) from the receptacle.
3. Remove the DC wiring from the refrigerator:
- Put a mark on the DC wires so you can put them back in the correct location.
- Remove the DC fuse or remove the DC wiring from the battery or the converter.
- Remove the DC wires from the refrigerator.
4. Open the lower intake vent and remove the gas supply line from the bulkhead tting of the refrigerator.
5. Remove the plastic plugs from the mounting anges of the refrigerator.
6. Remove the screws from the upper and lower mounting anges on the front of the refrigerator.
7. Remove the screws from the mounting ange at the rear of the refrigerator.
8. Remove the refrigerator from the opening.
Reinstall the Refrigerator
Your dealer or Norcold authorized service center must do this procedure.
Make sure the combustion seal is not broken, is completely around the refrigerator mounting anges, and
is between the mounting anges and the wall of the enclosure. If the combustion seal is not complete,
exhaust fumes can be present in the living area of the vehicle. The breathing of exhaust fumes can cause
dizziness, nausea, and in extreme cases, death.
1. Push the refrigerator completely into the enclosure.
2. Install the screws in the mounting ange at the rear of the refrigerator.
3. Install the screws from the upper and then the lower mounting anges on the front of the refrigerator.
4. Put the plastic plugs into the mounting anges of the refrigerator.
To avoid possible propane gas leaks, always use two wrenches to loosen and tighten the LP gas supply
line connections.
5. Attach the gas supply line to the bulkhead tting of the refrigerator.
6. Open the valve at the propane gas tank(s).
Do not allow the leak checking solution to touch the electrical components. Many liquids are electrically
conductive and can cause electrical shorts and in some cases, re.
7. Using a leak detecting solution, examine the gas supply line for leaks.
CAUTION
!
WARNING
!
WARNING
!
WARNING
!
WARNING
!
Owner’s Manual 18
Replacement Parts
You may purchase replacement parts through your local RV dealer or authorized Norcold Service Center.
Fault Codes
Fault Codes
No display.
“dr”
Audible alarm also.
“no” “FL”
Audible alarm also.
“no” “AC”
Audible alarm also.
“dc” “LO”
“LI” “oP”
Temperature number
ashes when SET
TEMP button is
pushed.
“AC” “rE”
Audible alarm also.
“AC” “HE”
Audible alarm also.
“Sr”
Audible alarm also.
Fault Code Meaning
DC voltage is
unavailable to
the refrigerator
control panel or the
refrigerator is OFF.
The door was open for
more than 2 minutes.
The burner did not
ignite or re-ignite.
AC voltage is
unavailable to the
refrigerator.
DC voltage to the
refrigerator control
panel is too low.
The high temperature
limit switch is open.
The refrigerator is
operating on the ‘Back
Up Operating System”.
This is a fault within the
refrigertor controls.
This is a fault within the
refrigertor controls.
This is a fault within the
refrigertor controls.
Corrective Actions
Check:
- That the refrigerstor is ON.
- That the battery charging equipment of the vehicle is
operational.
- That the AC/DC converter is operational (if applicable).
- See your dealer or Norcold authorized service center.
Close the door.
Check:
- That the valve of the propane gas tank(s) is open.
- That the propane gas is at the correct pressure.
- That the manual shut off valve of the refrigerator is open.
- That there is no air in the propane gas supply ines. See
“Removing air from hte propane gas supply lines” section of
this manual.
- See your dealer or Norcold authorized service center.
Check:
- That the refrigerator is plugged into a serviceable outlet.
- That the fuse or circuit breaker is intact.
- That the vehicle generator is operational (if applicable).
- See your dealer or Norcold authorized service center.
Check:
- That the battery charging equipment of the vehicle is
operational.
- That the AC/DC converter is operational (if applicable).
- See your dealer or Norcold authorized service center.
This is not owner serviceable. See your dealer or authorized Norcold Service
Center.
This is not owner serviceable. See your dealer or authorized Norcold Service
Center.
“This is not owner serviceable. See your dealer or authorized Norcold
Service Center.
This is not owner serviceable. See your dealer or authorized Norcold Service
Center.
This is not owner serviceable. See your dealer or authorized Norcold Service
Center.
8. Connect the DC wiring to the refrigerator:
- Connect the DC wires to the refrigerator.
- Install the DC fuse or connect the DC wiring to the battery or the converter.
9. Connect the black AC power cord and the white ice maker AC power cord (optional) to the receptacle.
Owner’s Manual 19
Wiring Diagram and Pictorial
The parts of the wiring diagram are (See Art02240):
The parts of the wiring pictorial are (See Art02241):
Temperature switch ..................................................................................................................................................................................A
AC heaters............................................................................................................................................................................................... B
Thermister ............................................................................................................................................................................................... C
Interior light .............................................................................................................................................................................................. D
Divider heater .......................................................................................................................................................................................... E
Door contacts ...........................................................................................................................................................................................F
Door switches .......................................................................................................................................................................................... G
Gas valve (optional)................................................................................................................................................................................. H
Fans...........................................................................................................................................................................................................I
Ice maker water line heater (optional) ......................................................................................................................................................J
Water valve heater (optional) .................................................................................................................................................................. K
Dispenser water line heater (optional) ......................................................................................................................................................L
Dispenser water valve heater (optional) ..................................................................................................................................................M
Dispenser valve (optional) ....................................................................................................................................................................... N
Fan temperature switch ........................................................................................................................................................................... O
Temperature switch (optional) ..................................................................................................................................................................P
Dispenser switch (optional) .....................................................................................................................................................................Q
Dispenser light (optional) ......................................................................................................................................................................... R
Igniter (optional)....................................................................................................................................................................................... S
Chassis ground.........................................................................................................................................................................................T
Movable door seal heater ........................................................................................................................................................................ U
Movable door seal housing ground ......................................................................................................................................................... V
Thermocouple..........................................................................................................................................................................................W
Switched 12 VDC .....................................................................................................................................................................................1
Fused continuous 12 VDC........................................................................................................................................................................2
Communications ....................................................................................................................................................................................... 3
Display ground..........................................................................................................................................................................................4
Auxilliary ground .......................................................................................................................................................................................5
Auxilliary +12 VDC ..................................................................................................................................................................................6
Divider + 12 VDC ......................................................................................................................................................................................7
Gas valve + 12 VDC ................................................................................................................................................................................. 8
5 Amp DC fuse .......................................................................................................................................................................................F1
8 Amp AC fuse ........................................................................................................................................................................................F2
Art02240
GND
12VDC
AC_HT_HI
F2
P2
1
10
2
L1
L2
YL/JN
BK/NR
YL/JN
BK/NR
AC_HT_LO
120 VAC
120 VCA
}
3
TEMP
T1
- 12 VDC/VCD
P1
4
1
2
3
+ 12 VDC/VCD
WH/BC
WH/BC
WH/BC
WH/BC
OR/OR
POWER BOARD / PANNEAU D’ALIMENTATION
ON-OFF
OVERLAY/REVÊTRMENT
MODE
DISPLAY BOARD/CARTE D’AFFICHAGE
8 AMP
AC_HT_LO
AC_HT_HI
1
2
3
4
5
6
LIMIT_IN
LIMIT_OUT
RD-WH/RG-BC
4
5
6
7
8
9
YL-GN-/JN-VE
WH/BC
WH/BC
B
B
H
-
+
WH-BK/BC-NR
F1
5 AMP
S
BK-WH/NR-BC
4
1
2
3
BK/NR
C
D
U
F
BK/NR
RD/RG
BK/NR
E
WH/BC
GN/VE
WH-RD/BC-RG
BU/BL
WH-VT/BC-VT
1
2
3
4
5
6
7
WH/BC
YL/JN
VT/VT
G G
1
2
3
4
5
T
T
BK/NR
BK/NR
BK/NR
BK/NR
O
RD/RG
RD/RG
RD/RG
P
RD/RG
WH/BC
WH/BC
J
BK/NR
WH BC
BK NR
BK/NR
K
WH/BC
WH BC
BK NR
BK/NR
L
WH/BC
WH BC
BK NR
BK/NR
M
WH/BC
Q
N
WH/BC
WH/BC
BK/NR
WH/BC
BK/NR
R
RD/RG
1
2
3
4
RD/RG
BK/NRBK/NR
RD/RG
RD/RG
RD/RG
RD/RG
BK/NR
P2
P1
+
+
-
-
5
6
7
8
V
T
RD/RG
RD/RG
BR/BR
BR/BR
T
GND
+12V IN
+12V OUT
A
+ -
W
RD/RG
YL/JN
Owner’s Manual 20
The parts of the ice maker wiring pictorial and diagram are (See Art01500):
120V AC Hot / smooth .......................................................................................................................................................................... 109
120 VAC Neutral / ribbed ...................................................................................................................................................................... 110
Ground screw ....................................................................................................................................................................................... 111
Thermal fuse......................................................................................................................................................................................... 114
Solenoid water valve ..............................................................................................................................................................................44
Ice maker .............................................................................................................................................................................................. 115
Mold heater........................................................................................................................................................................................... 116
Thermostat .............................................................................................................................................................................................96
Shut off switch ......................................................................................................................................................................................117
Fill switch .............................................................................................................................................................................................. 118
Hold switch ........................................................................................................................................................................................... 119
Motor ....................................................................................................................................................................................................120
Ice Maker Wiring Pictorial and Diagram (Optional)
Art01500
109
110
111
114
115
N
G
L
44
GRN / VERT
BRN / BRUN
WHT / BLANC
BLK / NOIR
NEUTRAL (RIBBED) /
NEUTRE (À NERVURES)
WHT / BLANC
HOT(SMOOTH)/
CHAUD (PLAT)
GRN / VERT
109
114
116
120
119
96
118
44
117
110
111
Art02241
5
L1
L2
P1
1
7
5
OVERLAY/REVÊTRMENT
DISPLAY BOARD/
CARTE D’AFFICHAGE
POWER BOARD/ PANNEAU D’ALIMENTATION
+12VDC/VCD
G
G
4
P2
T1
S
5 AMP
8 AMP
AC_HT_HI
LIMIT_IN
LIMIT_OUT
AC_HT_LO
AC_HT_HI
AC_HT_LO
GND
12VDC
T
B
B
11
T
8
-12VDC/VCD
H
7
M
L
K
J
N
R
P
Q
O
1
6
2
D
C
3
2
4
1
1
E
U
F
F
61
10
1
F
V
T
F2
F1
T
GND
+12V IN
+12V OUT
A
+ -
W
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
Norcold 1200 series Le manuel du propriétaire
- Taper
- Le manuel du propriétaire
- Ce manuel convient également à
dans d''autres langues
- English: Norcold 1200 series Owner's manual
Documents connexes
-
Norcold N61/N81 Series Le manuel du propriétaire
-
-
-
-
Norcold N4104/ N4141/ N4150 Le manuel du propriétaire
-
Norcold N64/N84 Le manuel du propriétaire
-
-
-
-
