Blodgett XR8-G Manuel utilisateur

Marque: Blodgett

Modèle: XR8-G

Catégorie: Cuisinières

Taper: Manuel utilisateur

Ce manuel convient également à

Microwave Oven XR8-G

BLODGETT OVEN COMPANY

www.blodgett.com

44 Lakeside Avenue, Burlington, Vermont 05401 USA Telephone (800) 331-5842, (802) 860-3700 Fax: (802)864-0183

PN 38480 Rev A (8/05)

E 2005 --- G.S. Blodgett Corporation

XR8 -G

MINI RACK OVEN

INSTALLATION -- OPERATION -- MAINTENANCE

XR8 -G

MINI RACK OVEN

MANUEL D’INSTALLATION -- FONCTIONNEMENT -- ENTRETIEN

IMPORT

FORYOURSAFETY

Do not store or use g asoline or other flammable vapors or liquids in the vicinity

of this or any other appliance.

AVERTIS SEMENT

Ne pas entreposer ni utiliser de l’essence ni d’autres vapeurs ou liquides inflam-

mables dans le vois in a ge de cet appar iel, ni de tout autr e appar eil.

INSTRUCTIONS (PAGE 12) TO BE FOLLOWED IN THE EVENT THE USER

SMELLS GAS MUST BE POSTED IN A PROMINENT LOCATION. THIS INFORMA-

TION MAY BE OBTAINED BY CONTACTING YOUR LOCAL GAS SUPPLIER.

LESINSTRUCTIONS (PAGE 12) À RESPECTER AUCASOÙ L’UTILISATEUR PER-

ÇOIT UNE ODEUR DE GAZ DOIVENT ÊTRE AFFICHÉES DANS UN ENDROIT BIEN

VISIBLE. VOUS POUVEZ VOUS LES PROCURER AUPRÈS DE VOTRE FOURNIS-

SEUR DE GAZ LOCAL.

WARNING: IMPROPER INSTALLA TION, ADJUSTMENT, ALTERA TION, SERVICE OR

MAI NTEN A NC E CAN CA US E PROP ERTY DAMAG E, INJURY OR DEATH. READ THE

INST ALLA TION, OPERA TING AND MAINTENANCE INSTRUCTIONS THOROUGHLY

BEFORE INST ALLING OR SERVICING THIS EQUIPMENT

A V ERTI SSEMEN T: UNE INSTALLATION, UN AJUSTEMEN T, UNE ALTÉRATION , UN

SERV IC E OU UN ENTRETI EN NON CONFO RME A UX NORMES PEUT CA US ER DES

DO MMA GES À LA PROP RI ÉTE, DES BLESSURES OU LA MORT. LIS EZ ATTENTIV E-

MENT LES DIREC TI V ES D’ I NS TALL ATION, D’O P ÉRATION ET D’ ENTRETI EN AV A N T

DE FAIRE L’IN S TALLATION OU L’ENTRETIEN DE CET ÉQUI P EMEN T.

The information contained in thi s manual is important for the proper installation,

use, and maintenance of this oven. Adherence to these procedures and instruc-

tions will result in satisfactory baking results and long, trouble free service.

Please read this manual carefully and retain it for future reference.

Les info r m a t ions données da ns le présent manuel sont impor tantes pour installer,

utiliser et entr et enir co r r ect em ent ce fou r. Le r es pect de ces ins tructio n s et pro cé-

dures permettra d’obtenir de bons résultats de cuisson et une longue durée de ser-

vice sans problèmes. Veuillez lire le présent manuel et le conserver pour pouvoir

vou s y repor t er à l’avenir.

Errors: Descriptive, typographic or pictorial errors are subject to correction. Specifica-

tions are subject to change without notice.

Erreurs:Les erreurs de description, de typographie ou d’illustration font l’objet de

corrections. Les caractéristiques sont sujettes à modifications sans préavis.

THE REPUTATION YOU CAN COUNT ON

UNE RÉPUTATION SUR LAQUELLE VOUS POUVEZ COMPTER

For over a century and a half, The Blodgett Oven Company has been building

ovens and nothing but ovens. We’ve set the industry’s quality standard for all

kinds of ovens for every foodservice operation regardless of size, a pplication

or budget. In fact, no one offers more models, sizes, and oven applications

than Blodgett; gas and electric, full-size, half-size, countertop and deck, con-

vection, Cook’n Hold, Combi-Ovens and the industry’s highest quality Pizza

Oven line. For more information on the full line of Blodgett ovens contact your

Blodgett representative.

Cela fait maintenant dessus un siècle et demi que Blodgett se spécialise dans

la fabrication de fours. Nous avons établi les normes de qualité qui s’appli-

quent dans l’industrie à tous les types de fours utilisés dans les services ali-

mentaires, quel qu’en soit la taille, l’exploitation ou le budget. En fait, ni n’offre

plus de modèles, de tailles et d’applications de fours que Blodgett. À gaz et

électriques. De tailles différentes, sur plan de travail et superposables. Qu’il

s’agisse de fours à convection, des modèles Cook’n Hold et Combi-Oven, ou

de la gamme de fours à pizzas de la plus haute qualité offerte sur le marché.

Pour de plus amples informations sur la gamme complète de fours B lodgett,

veuillez contacter votre représentant B lodgett.

Your Service Agency’s Address:

Adressedevotreagencedeservice:

Model/Modèle:

Serial Number/Numéro de série:

Your oven was installed by/

Installateur de votre four:

Your oven’s installation was checked by/

Contrôleur de l’installation de votre four:

Table of Contents/Table des Matières

Introduction

Oven Description and Specifications 2....

Installation

Delivery and Location 3.................

Oven Assembly 4......................

Assembly to Stand 4..................

Assembly to Optional Proofer 4.........

V entilation 5...........................

Utility Connections ---

Standards and Codes 6.................

Gas Connection 7......................

Plumbing and Electrical Connections 10...

Initial Startup 11.........................

Operation

Safety Information 12....................

Standard Control 13.....................

General Guidelines for

Operating Personnel 15..................

Maintenance

Cleaning and Preventative Maintenance 16.

Troubleshooting Guide 17................

Introduction

Description et Spécifications du Four 18....

Installation

Livraison et Implantation 19...............

Montage du Four 20.....................

Assembly to stand 20..................

Assembly to optional proofer 20.........

V entilation 21...........................

Branchements de Service ---

Normes et Codes 22.....................

Branchement de Gaz 23.................

Raccordement Électrique et Plomberie 26..

Mise en Marche Initiale 27................

Utilisation

Informations de Sécurité 28...............

Standard Control 29.....................

Consignes Générales à l’Intention

des Utilasateurs 31......................

Entretien

Nettoyage et Entretien Préventif 32........

GuidedeDétectiondesPannes 33........

Introduction

Oven Description a nd Specifications

The Blodgett M ini -Rack oven features a continu-

ously rotating eight pan rack and unique airflow

system that moves large amounts of air at low ve -

locity to ensure a consistently even bake. The

Blodgett rack slide sytem allows the operator t o

quickly adjust slide spacing from 1 to 4 inches in

any configuration. In addition, the Mini-Rack oven

is capable of producing large volumes of steam for

bagels or similar products.

GAS SPECIFICATIONS -- XR8-G/AA

Natural Gas Propane Gas

US Units SI Units US Units SI Units

Heating V alue 1000 BTU/cu. ft. 37.3 MJ/m

2550 BTU/cu. ft. 95.0 MJ/m

Specific Gravity (air=1.0) 0.63 0.63 1.53 1.53

Gas Manifold Pressure 3.5” W.C. .87 kPa 10” W.C. 2.5 kPa

Oven Input 110,000 BTU/hr 32 kW

116 MJ/hr

110,000 BTU/hr 32 kW

116 MJ/hr

Main Burner Orifice Size:

Six burners are

Two burners are

.07” dia.

.061” dia.

1.7 mm

1.5 mm

.043” dia.

.038” dia.

1.0 mm

0.96 mm

PLUMBING SPECIFICATIONS -- XR8-G/AA

Water

Water Pressure 30 PSI (21 kPa) minimum

75 PSI (52 kPa) maximum

Water Connection 3/4” MGHT

Flow Rate 1.12 gallon/minute (4.24 litre/minute) minimum

Drainage

Drain Connection 3/4” rear drain to air gap drain

Installation

Delivery and Location

DELIVERY AND INSPECTION

All Blodgett ovens are shipped in containers to

prevent damage. Upon delivery of your new oven:

D Inspect the shipping container for external dam-

age. Any evidence of damage should be noted

on the delivery receipt which must be signed by

the driver.

D Uncrate the oven and check for internal dam-

age. Carriers will accept claims for concealed

damage if notified within fifteen days of delivery

and the shipping container is retained for in-

spection.

The Blodgett Oven Company cannot assume

responsibility for loss or damage suffered in

transit. The carrier assumed full responsibility

for delivery in good order when the shipment

was a ccepted. We are, however, prepa red to

assist you if filing a cla im is necessary.

OVEN LOCATION

The well planned and proper placement of your

oven will result in long term operator convenience

and satisfactory performance.

The following clearances must be maintained be-

tween the oven and any combustible or non-com-

bustible construction.

D Oven body right side --- 0” (0 cm)

D Oven body left side --- 0” (0 cm)

D Oven body back --- 0” (0 cm)

D Oven top --- 12” (30.5 cm)

The following clearances must be available for ser-

vicing.

D Oven body sides --- 12” (30 cm)

D Oven body back --- 12” (30 cm)

D Oven top --- 12” (30.5 cm)

NOTE: On gas models, routine servicing can usu-

ally be accomplished within the limited

movement provided by the gas hose re-

straint. If the oven needs to be moved fur-

ther from the wall, the gas must first be

turned off and disconnected from the oven

before removing the restraint. Reconnect

the restraint after the oven has been re-

turned to its normal position.

It is essential that a n adequate air supply to the

oven be maintained to provide a sufficient flow of

combustion and ventilation air.

D Place the oven in an area that is free of drafts.

D Keep the oven area free and clear of all combus-

tibles such as paper, cardboard, and flammable

liquids and solvents.

D Do not place the oven on a curb ba se or seal to

a wall. This will restrict the flow of air and prevent

proper ventilation. Tripping of the blower mo-

tor’s thermal overload device is caused by an

excessive ambient temperature on the right

side of the oven. This condition must be cor-

rected to prevent permanent damage to the

oven.

D The locatio n must provide adequate clearance for

the air opening into the burners.

Before making any utility connections to this oven,

check the rating plate to be sure the oven specifi-

cations are compatible with the gas and electrical

services supplied for the oven.

1. The rating plate is located behind the control

panel.

2. Remove the two screws on the right side of the

control panel.

3. Pull the control panel toward the right side of

the oven.

4. Pull the control panel away from the oven and

rotate out.

5. Reverse steps 2-4 t o close the control panel.

Installation

Oven Assembly

ASSEMBLY TO STAND

1. Center the oven frame on top of the stand so

that the oven overhangs at both the front and

back. See Figure 1.

2. Remove the three screws at the top of the left

and right side panels of the oven. Remove the

side panels.

3. Align the two bolt holes on each side of the

stand with the two threaded holes on each

sideoftheoven.SeeFigure1.

4. Insert a bolt from the bottom up through each

of the two holes and tighten securely.

5. Reinstall t he side panels.

ASSEMBLY TO OPTIONAL PROOFER

1. Center the oven frame on top of the proofer so

that the oven overhangs at both the front and

back. See Figure 1.

2. Remove the four screws on the back of the

proofer. Remove t he left and right side panels.

3. Align the two bolt holes on each side of the

proofer with the two threaded holes on each

sideoftheoven.SeeFigure1.

4. Insert a bolt from the bottom up through each

of the two holes and tighten securely.

5. Reinstall t he side panels.

SIDE VIEW WITH OPTIONAL PROOFERSIDE VIEW WITH STAND

Figure 1

Installation

Ventilation

On gas models the installation of a proper ventila-

tion system cannot be over emphasized. This sys-

tem removes unwanted vapors and products of

combustion from the operating area.

U.S. and Canadian installations

Refer to your local ventilation codes. In the ab-

sence of local codes, refer to the National ventila-

tion code titled, “Standard for the Installation of

Equipment for the Removal of Smoke and Grease

Laden Vapors from Commercial Cooking Equip-

ment”, NFPA-96-Latest Edition.

General export installations

Installation must conform with Local and National

installation standards. Local installation codes

and/or requirements may vary. If you have any

questions regarding the proper installation and/or

operation of your Blodgett oven, please contact

your local distributor. I f you do not have a local dis-

tributor, please call the Blodgett Oven Company at

0011-802-860-3700.

WARNING:

Failure to properly vent the oven can be

hazardous to the health of the operator

and may result in operational problems,

unsatisfactory baking and possible dam-

age to the equipment.

Damage sustained as a direct result of im-

proper ventilation will not be covered by

the manufacturer’s warranty.

CANOPY TYPE EXHAUST HOOD

A mechanically driven, canopy type exhaust hood

is the preferred method of ventilation. The exhaust

fan should have an interlock switch with the oven

to prevent the oven from operating when the ex-

haust fan is not running.

The hood should be sized to completely cover the

equipment plus an overhang of at least 6” (15 cm)

on all sides not adjacent t o a wall. The distance

from the floor to the lower edge of the hood should

not exceed 7’ (2.1m).

The total makeup and exhaust air requirements for

hood capacity should be approximately 35 CFM

(.99 m

/min).

Installation

Utility Connections --- Standards and Codes

THE INST ALLA TION INSTRUCTIONS CONT AINED

HEREIN ARE FOR THE USE OF QUALIFIED IN-

ST ALLA TION AND SERVICE PERSONNEL ONLY.

INSTALLATION OR SERVICE B Y OTHER THAN QU-

ALIF IED PERSO N N EL MA Y RESULT IN DAMAGE

TO THE OVEN AND/OR INJURY TO THE OPERA-

TOR.

Qualified installation personnel are individuals, a

firm, a corporation, or a company which either in

person or through a representative are engaged

in, and responsible for:

D the installation or replacement of gas piping

and the connection, installation, repair or serv-

icing of equipment.

D the installation of electrical wiring from the elec-

tric meter, main control box or service outlet to

the electric appliance.

Qualified installation personnel must be experi-

enced in such work, familiar with all precautions

required, and have complied w ith all requirements

of state or local authorities having jurisdiction.

U.S. and Canadian installations

Installation must conform with local codes, or in

the absence of local codes, with the ANSI Z83.11a-

CSA 1.8a-2004 Gas Food Service Equipment as

applicable.

Installation must conform with local codes, or in

the absence of local codes, with the National Elec-

trical Code, ANSI/NFPA 70 ---Latest Edition and/or

CSA 22.1 as applicable.

General export installations

Installation must conform with Local and National

installation standards. Local installation codes

and/or requirements may vary. If you have any

questions regarding the proper installation and/or

operation of your Blodgett oven, please contact

your local distributor. I f you do not have a local dis-

tributor, please call t he Blodgett Oven Company at

0011-802-860-3700.

Installation

Gas Connection

GAS PIPING

A properly sized gas supply system is essential for

maximum oven performance. Piping should be

sized to provide a supply of gas sufficient to meet

the maximum demand of all appliances on the line

without loss of pressure at the equipment.

Example:

NOTE: BTU values in the following example are

for natural gas.

YoupurchaseaXR8-Grackoventoaddtoyourex-

isting cook line.

1. Add the BTU rating of your current appliances.

Pitco Fryer 120,000 BTU

6 Burner Range 60,000 BTU

Deck Oven 50,000 BTU

Total 230,000 BTU

2. Add the BTU rating of t he new oven to the to-

tal.

Previous Total 230,000 BTU

XR8-G 110,000 BTU

New Total 340,000 BTU

3. Measure the distance from the gas meter to

the cook line. This is the pipe length. Let’s say

thepipelengthis30’(9.1m)andthepipesize

is 1” (2.54 cm).

4. Use the appropriate table to determine the to -

tal capacity of your current gas piping.

The total capacity for this example is 375,000

BTU. Since the total required gas pressure,

340,000 BTU is less than 375,000 BTU, the

current gas piping will not have to be in-

creased.

NOTE: The BTU capacities given in the tables are

for straight pipe lengths only. Any elbows

or other fittings will decrease pipe capaci-

ties. Contact your local gas supplier if you

have any questions.

Maximum Capacity of Iron Pipe in Cubic Feet

of Natural Gas Per Hour

(Pressure drop of 0.5 Inch W.C.)

Pipe

(

)

Nominal Size, Inches

Length (ft)

3/4” 1” 1-1/4” 1-1/4” 2”

10 360 680 1400 2100 3950

20 250 465 950 1460 2750

30 200 375 770 1180 2200

40 170 320 660 990 1900

50 151 285 580 900 1680

60 138 260 530 810 1520

70 125 240 490 750 1400

80 118 220 460 690 1300

90 110 205 430 650 1220

100 103 195 400 620 1150

From the National Fuel Gas Code Part 10 Table 10-2

Maximum Capacity of Pipe in Thousands of

BTU/hr of Undiluted L.P. Gas at 11” W.C.

(Pressure drop of 0.5 Inch W.C.)

Pipe Length

(

)

Outside Diameter, Inches

(ft)

3/4” 1” 1-1/2”

10 608 1146 3525

20 418 788 2423

30 336 632 1946

40 287 541 1665

50 255 480 1476

60 231 435 1337

70 215 404 1241

80 198 372 1144

90 187 351 1079

100 175 330 1014

From the National Fuel Gas Code Part 10 Table 10-15

Installation

Gas Connection

PRESSURE REGULATION AND TESTING

XR8-G ovens are rated at 110,000 BTU/Hr. (32 kW)

(116 MJ/hr). Each oven has been adj usted at the

factory to operate with the type of gas specified on

the rating plate.

Inlet Pressure

Natural Propane

Min Max Min Max

W.C. 6.0 14.0 11.0 14.0

kPa 1.2 3.5 2.7 3.5

Manifold Pressure

Natural Propane

W.C. 3.5 10.0

kPa .87 2.5

D Inlet Pressure --- the pressure of the gas before

it reaches the oven.

D Manifold Pressure --- the pressure of the gas

as it enters the main burner(s).

D Min --- the minimum pressure recommended to

operate the oven.

D Max --- the maximum pressure at which the

manufacturer warrants the oven’s operation.

Each oven is supplied with a regulator to maintain

the proper gas pressure. The regul ator is essen-

tial to the proper operation of the oven and

should not be removed. It is preset to provide the

oven with 3.5” W.C. (.87 kPa) for natural gas and

10.0” W. C. (2.5 kPa) for Propane at the manifold.

DO NOT INSTALL AN ADDITIONAL REGULATOR

WHERE THE OVEN CONNECTS TO THE GAS

SUPPLY UNLESS THE INLET PRESSURE IS

ABOVE MAXIMUM.

Prior to connecting the oven, gas lines should be

thoroughly purged of all metal filings, shavings,

pipe dope, and other debris. After connection, the

oven should be checked for correct gas pressure.

The oven and its individual s hutoff valve must be

disconnected from the gas supply piping system

during any pressure testing of that system at test

pressuresinexcessof1/2psig(3.45kPa).

The oven must be isolated from the gas supply

piping system by closing its individual manual

shutoff valve during any pressure testing of the

gas piping system at test pressures equal or less

than 1/2 psig (3.45kPa).

Gas Connection

2.78” (71 mm)

Gas Connection

37.83 (961mm)

SIDE VIEW WITH STAND

Gas Connection

53.62 (1362)

SIDE VIEW WITH OPTIONAL PROOFER

Figure 2

Installation

Gas Connection

GAS HOSE RESTRAINT

If the oven is mounted on casters, a commercial

flexible connector with a minimum of 3/4” (1.9 cm)

inside diameter must be used along with a quick

connect device.

The restraint, supplied with the oven, must be

used to limit t he movement of the unit so that no

strain is placed upon the flexible connector. With

the restraint fully stretched the connector should

be easy to install and quick connect.

The restraint (ie: heavy gauge cable) should be

1,000 lb. (453 kg) test load and should be attached

without damaging the building. D O NOT use the

gas piping or electrical conduit for the attachment

of the permanent end of the restraint! Use anchor

bolts in concrete or cement block. On wooden

walls, drive hi test wood lag screws into the studs

of the wall.

1. Mount the supplied bracket to the leg bolt be-

low the gas inlet. See Figure 3.

2. Attach the clip on restraining cable to the

mounting bracket.

Restraint Cable

Bracket

Back of Oven

Figure 3

WARNING!!

If the restraint is disconnected for any

reaso n it must be reconnected when the

oven is returned to its original position.

U.S. and Canadian installations

The connector must comply with the Standard for

Connectors for Movable Gas Appliances, ANSI

Z21.69

CSA 6.16 and a quick disconnect device

that complies with the Standard for Quick- Discon-

nect Devices for Use With Gas Fuel, ANSI Z21.41

CSA 6.9. Adequate means must be provided to

limit the movement of the appliance without de-

pending on the connection and the quick discon-

nect device or its associated piping.

General export installations

The restraint and quick connect must conform

with Local and National installation standards. Lo-

cal installation codes and/or requirements may

vary. If you have any questions regarding t he prop-

er installation and/or operation of your Blodgett

oven, please contact your local distributor. If you

do not have a local distributor, please call the

Blodgett Oven Company at 0011-802-860-3700.

Installation

Plumbing and Electrical Connections

PLUMBING CONNECTIONS

WARNING!!

Plumbing connections must comply with

applicable sanitary, safety and plumbing

codes.

Water Connections

Water supply should meet the following condi-

tions. Consult your local water company before

installing the oven.

D Hardness of 4- 6 grains per gallo n (100ppm max)

D PH of 6.5 to 8.0

D Chlorideslessthan30PPM

1. Connect the cold wat er supply to the 3/4”

MGHT connection on the back of the oven

with the water line provided. Supply pressure

should be 30 to 75 psi (207 to 517 kPa) when

the steam solenoid is open. The water regula-

tor on the oven itself must be set to 15 psi (103

kPa) when the steam solenoid is open.

Drain Connections

1. Connect drain line to the 3/4” NPT drain con-

nection on t he back of the oven.

2. Route the drain line to a floor drain. Allow a 1”

air gap between the drain line and the floor

drain.

NOTE: When the oven is stacked on a proofer a

separate drain line s hould be installed. If

a second drain line is not possible, pro-

vide a vent opening in the drain line above

the oven drain connection. Be sure to pro-

vide enough drop so the oven drain will not

flood the proofer cabinet.

ELECTRICAL CONNECTIONS

Wiring diagrams are located in the right bodyside.

This oven is supplied for connection to a 120 volt

grounded circuit. The electric motor, indicator

lights and related switches are connected through

the 6’ electric supply cord found at the rear of the

oven.

NOTE: When the oven is installed with a proofer a

separate 120 volt grounded circuit will be

required.

WARNING!!

This appliance is equipped with three

pronggroundingtypeplugforyour

protection against shock hazard and

should be plugged directly into a properly

grounded three prong receptacle. DO

NOT cut or remove the grounding prong

from this plug.

THE BLODGETT OVEN COMPANY CANNOT AS-

SUME RESPONSIBILITY FOR LOSS OR DAMAGE

SUFFERED AS A RESULT OF IMPROPER INSTAL-

LA TION.

ELECTRICAL SPECIFICATIONS

Model Hz Volts Phase Amps Electrical Connection

(minimum size)

XR8-G 60 120 1 5 Cord set provided

Installation

Initial Startup

The following is a check-list to be completed by

qualified personnel prior to turning on the

applianceforthefirsttime.

j Verify there a re no gas leaks, by checking all

gas connections with a soapy water solution.

Repair leaks if necessary.

j Verify there are no water leaks to the oven. Re-

pair leaks if necessary.

j Verify rack rotation as follows: Open oven

doors and turn the power switch to ON. Close

the doors a nd enter bake time of two minutes.

Press start. Verify the rack rotates smoothly.

Open the doors. Verify the rack stops square

to the door opening. If rack does not rotate

and fan does not circulate, door switch may

be out of adjustment.

With the main burner on, check the following:

j Set the oven temperature to 300_F. Ve r i f y t h a t

the oven comes up to set temperature.

j Set a steam time of 20 seconds. Verify that the

oven water pressure is 15 psi when the water

solenoid valve is open. The water pressure

gauge is located under the right side panel of

the oven. Panel must be removed.

j Verify that the gas inlet pressure is correct.

The inlet pressure can be checked at the pres-

sure tap located on the gas valve.

j Verify that the manifold pressure is correct.

The manifold pressure can be checked at the

outlet pressure tap located on the burner gas

manifold elbow located on top of the oven.

j If the above pressure readings are set to the

recommended pressure requirements, a llow

the oven to burn-off for two hours with oven

vent opened. If the pressure readings are not

set correctly, turn off the oven and readjust ac-

cordingly. Then recheck pressure readings.

WARNING

The break in procedure burns off excess

oils present in the metals during fabrica-

tion. Smoke may be produced. Proper

ventilation is required.

ADJUSTMENTS ASSOCIATED WITH INITIAL

INSTALLATION

Each oven, and its component parts, have been

thoroughly tested and inspected prior to ship-

ment. However, it is often necessary to further test

or adjust the oven as part of a normal and proper

installation. These adjustments are the responsi-

bility of the installer, or dealer. Since these adjust-

ments are not considered defects in material or

workmanship, they are not covered by the Original

Equipment Warranty. They include, but are not

limited to:

D calibration of the thermostat

D adjustment of the doors

D burner adjustments

D leveling

D testing of gas pressure

D tightening of fasteners

D rack rotation stop position

No installation should be considered complete

without proper inspection, and if necessary, ad-

justment by qualified installation or service per-

sonnel.

Operation

Safety Information

THE INFORMATION CONTAINED IN THIS SEC-

TION IS PROVIDED FOR THE USE OF QUALIFIED

OPERATING PERSONNEL. QUALIFIED OPERAT -

ING PERSONNEL ARE THOSE WHO HAVE

CAREFULLY READ THE INFORMATION CON-

TAINED IN THIS MANUAL, ARE FAMILIAR WITH

THE FUNCTIONS OF THE OVEN AND/OR HAVE

HAD PREVIOUS EXPERIENCE WITH THE OP-

ERATION OF THE EQUIPMENT DESCRIBED. AD-

HERENCE TO THE PROCEDURES RECOM-

MENDED HEREIN WILL AS SURE THE

ACHIEVEMENT OF OPTIMUM PERFORMANCE

AND LONG, TROUBLE-FREE SERVICE.

Please take the time to read the following safety

and operating instructions. They are the k ey to the

successful operation of your Blodgett mini rack

oven.

SAFETY TIPS

For your safety read bef ore operating

What to do if you smell gas:

D DO NOT try to light any appliance.

D D O NOT touch any electrical s witches.

D Use an exterior phone to call your gas supplier

immediately.

D If you cannot reach your gas supplier, call the

fire department.

What to do in the event of a power failure:

1. Turn all switches to off.

2. DO NOT attempt to operate the oven until the

power is restored.

NOTE: In the event of a shut-down of any kind, al-

low a five (5) minute shut off period before

attempting to restart the oven.

General safety tips:

D DO NOT use tools t o turn off the gas control. If

the gas cannot be turned off manually do not try

to repair it. Call a qualified service technician.

D If the oven needs to be moved for any reason

disconnect the water. The gas must be turned

off and disconnected from the unit before re-

moving the restraint cable. Reconnect the re-

straint after the oven has been returned to its

original location.

D DO NOT remove the control panel cover or right

body panel unless t he oven is unplugged.

D The rack will stop/finish rotating when the doors

are opened.

Operation

Solid State Digital Control

Figure 4

CONTROL DESCRIPTION

1. POWER SWITCH - controls power to the oven

2. D I SPLAY - displays time, temperature and

programming information

3. HEAT LED - lights when the burners are on

4. READY LED - lights when oven has reached

the preset t emperature

5. ACTUAL TEMP LED - lights when temp key is

pressed, actual temp is displayed

6. SELECTION D IAL - use to enter time, temper-

ature and programmable settings. Turn clock-

wise to increase or counter-clockwise to de-

crease values in display.

7. TEMP KEY - press to program the bake tem-

perature or display the actual oven tempera-

ture

8. TIME KEY - press t o program the bake time or

display the time during a bake cycle

9. STEAM KEY - press to program steam time to

inject a burst of steam

10. FAN DELAY KEY - press to program a time delay

for fan and heat during and after steaming

11. VENT KEY - press to manually open and close

the oven vent

12. START/STOP KEY - press to start, stop or

pause the bake

13. GAS SHUTOFF SWITCH - controls gas flow to

the oven

Operation

Standard Control

OPERATION

Oven Startup

1. Be sure the GAS SHUTOFF SWITCH (13) is in

the on position.

2. Tu rn the POWER SWITCH (1) to the on posi-

tion. The HEAT LED (3) lights and the oven

preheats to the last used set temperature.

Programming a Bake Cycle

1. Press the TEMP KEY (7). Turn the DIAL (6) to

the desired bake temperature.

2. Press the TIME KEY (8). Turn the DIAL (6) to

the desired bake time.

3. If steam is desired, press the STEAM KEY (9).

Turn the DIAL (6) to the desired steam time.

Steam may be programmed for the beginning

ofthebakecycleforuptotwominutes.

4. Ifyouwishtodelaytherotationoftheconvec-

tion fan at the beginning of the bake cycle,

press the FAN DELAY (10) key. Turn t h e DIA L

(6) to the desired fan delay time.

5. Press the START/STOP KEY (12) to begin the

bake cycle. The oven rack rotates.

DuringtheBakeCycle

1. To view the remaining bake time, press the

TIME KEY (8).

2. To view the actual oven temperature, press

the TEMP KEY (7).

3. To inject up to two minutes of steam during the

bake cycle, press the STEAM KEY (9).

4. To vent moisture from the oven cavity, press

the VENT KEY (11). This manually opens the

oven vent until the key is pressed again to

close it.

5. To pause a bake cycle at any point, press t he

START/STOP KEY (12). The cycle will pause

until the key is pressed again.

AttheEndoftheBakeCycle

1. Attheendofthebakecycle,analarmsounds,

the display reads DONE a nd the rack contin-

ues to rotate until the door is opened. Press

the START/STOP K EY (12) to silence the

alarm.

2. Open the door to remove the product.

Oven Shutdown

1. Turn the POWER SWITCH (1) to the off posi-

tion.

Operation

General Guidelines for Operating Personnel

BAKE TIMES AND TEMPERATURES

Preheating the oven

Always preheat the oven before baking or roast-

ing. We recommend preheating 50_F(10_C)

above the bake temperature to offset the drop in

temperature when the doors are opened and cold

product is loaded into the oven. Set the thermostat

to the bake temperature after the product is

loaded.

Bake Time

Check the product in about half the time recom-

mended for deck or range oven recipes. Record

times and temperatures which provide best re-

sults for future reference.

NOTE: Baketimewillvarywiththeamountof

product loaded, the type of pan and the

temperature.

OPERATING TIPS

Pans and Racks

Product or pan height determines how many

racks are used. The oven holds up to eight 18” x

24” (45.7 x 61 cm) bun pans with 4” rackspacing.

Load the oven from the bottom, centering t he pans

on the rack.

Roasting

To reduce shrinkage when roasting, place meat

directly on the racks. Place a sheet pan one-half

full of water in t he bottom rack position. The water

evaporates, increasing humidity in the oven

chamber. The pan catches grease from the meat,

making oven cleaning easier.

Fans

The fan must be operating for the oven to heat. To

avoid rippling of batter product use the following

procedure.

1. Preheat the oven 25_ F(15_C) above the bak-

ing temperature.

2. Loadtheovenwithproduct.Closethedoors.

3. Set the thermostat to the baking temperature.

4. Set the blower delay for two minutes.

Cool Down Mode

To facilitate cooling the oven to a lower tempera-

ture, press the TEMP KEY (7) and turn the DIAL (6)

to the left until the display reads COOL.

Maintenance

Cleaning and Preventative Maintenance

CLEANING THE OVEN

Stainless steel ovens may be kept clean and in

good condition with a light oil. Deposits of baked

on splatter, heat tint and heavy discoloration may

be removed with any non-toxic industrial stainless

steel cleaner.

1. Apply cleaners when the oven is cold. Always

rubwiththegrainofthemetal.

2. Dry the oven with a clean cloth.

Clean interior parts as follows:

1. Remove the rack from the oven.

2. Soak the parts in a s olution of ammonia and

water.

3. Reinstall after cleaning.

NOTE: If the oven is moved the restraint must be

reconnected after the unit is returned to it’s

regular position.

PREVENTATIVE MAINTENANCE

The best preventative maintenance measures are,

the proper installation of the equipment and a pro-

gram for routinely cleaning the ovens.

Annual Maintenance

This oven requires no lubrication. Maintenance

should be based on hours of usage. Refer to

OSHA specifications for maintenance intervals.

If maintenance or repairs are required, contact

your local Blodgett service company, a factory

representative or the Blodgett Oven company.

NOTE: All service functions can be reached from

the top of the oven or by removing the right

side body panel.

WARNING!!

Always disconnect the appliance from the

power supply before servicing or cleaning.

La page charge ...

Blodgett XR8-G Manuel utilisateur

Marque: Blodgett

Modèle: XR8-G

Catégorie: Cuisinières

Taper: Manuel utilisateur

Ce manuel convient également à

Microwave Oven XR8-G

Télécharger le PDF

rapport

dans d''autres langues

English: Blodgett XR8-G User manual

Blodgett XR8-G Manuel utilisateur

Ce manuel convient également à

Blodgett XR8-G Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents