WAGNER PROCOAT MAX Le manuel du propriétaire

Marque: WAGNER

Modèle: PROCOAT MAX

Catégorie: Systèmes de pulvérisation fine Power

Taper: Le manuel du propriétaire

Ce manuel convient également à

ProCoat Plus

Español Français English

Owner’s Manual

Read this manual for complete instructions

0312 • Form No. 0504986D

Contents

2 Important Safety Information

4 What’s in the Box?

5 Proper Use and Functions

6 Assembly

7 Pressure Relief Procedure

8 Load Material

9 Getting Material to Flow

10 Practice Spraying

12 Clear the Spray Tip

13 Clean the Spray Gun Filter

Français (page 25) / Español (página 49)

PROCOAT

PLUS

™

Questions?

Call Wagner Technical Service at:

1-800-328-8251

www.wagnerspraytech.com

Proper registration will serve as proof

of purchase in the event your original

receipt becomes misplaced or lost.

14 Clean the Inlet Filter

15 Short Term Storage

16 Cleanup - latex materials

18 Cleanup - oil-based materials

19 Cleaning the Spray Gun Components

20 Long-Term Storage

21 Replacing the Outlet/Inlet Valves

22 Troubleshooting

72 Parts List

76 Warranty

English

SafetySafety

Important Safety

Information

Read all safety information before operating

the equipment. Save these instructions

Indicates a hazardous situation which, if not

avoided, could result in death or serious injury.

 a) Toreducetherisksofreorexplosion,electrical

shock and the injury to persons, read and

understand all instructions included in this manual.

Be familiar with the controls and proper usage of

the equipment.

Grounding Instructions

This product must be grounded. In the event of an electrical

short circuit, grounding reduces the risk of electric shock

by providing an escape wire for the electric current. This

product is equipped with a cord having a grounding wire with

an appropriate grounding plug. The plug must be plugged

into an outlet that is properly installed and grounded in

accordance with all local codes and ordinances.

WARNING - Improper installation of the

grounding plug can result in a risk of electric

shock.

If repair or replacement of the cord or plug is necessary,

do not connect the green grounding wire to either at blade

terminal. The wire with insulation having a green outer

surface with or without yellow stripes is the grounding wire

and must be connected to the grounding pin.

Check with a qualied electrician or serviceman if the

grounding instructions are not completely understood, or

if you are in doubt as to whether the product is properly

grounded. Do not modify the plug provided. If the plug

will not t the outlet, have the proper outlet installed by a

qualied electrician.

This product is for use on a nominal 120 volt circuit and

has a grounding plug that looks like the plug illustrated

below. Make sure that the product is connected to an

outlet having the same conguration as the plug. No

adapter should be used with this product.

Grounded Outlet

Grounding Pin

Cover for grounded outlet box

b) WARNING - To reduce the risk of

reorexplosion:

1. Do not spray ammable or

combustible materials near an open ame, pilot

lights or sources of ignition such as hot objects,

cigarettes, motors, electrical equipment and

electrical appliances. Avoid creating sparks from

connecting and disconnecting power cords.

2. Do not spray or clean with liquids having a ash

point of less than 21ºC (69.8ºF). Flash point is the

temperature at which a uid can produce enough

vapor to ignite.

3. Paint or solvent owing through the equipment is

able to result in static electricity. Static electricity

creates a risk of re or explosion in the presence

of paint or solvent fumes. All parts of the spray

system, including the pump, hose assembly, spray

gun and objects in and around the spray area

shall be properly grounded to protect against static

discharge and sparks. Use only conductive or

grounded high-pressure airless paint sprayer hoses

specied by the manufacturer.

4. Verify that all containers and collection systems are

grounded to prevent static discharge.

5. Connect to a grounded outlet and use grounded

extension cords (electric models only). Do not use

a 3 to 2 adapter.

6. Do not use a paint or solvent containing

halogenated hydrocarbons. Such as chlorine,

bleach mildewcide, methylene chloride and

trichloroethane. They are not compatible with

aluminum. Contact the coating supplier about

compatibility of material with aluminum.

7. Keep spray area well ventilated. Keep a good

supply of fresh air moving through the area to keep

the air within the spray area free from accumulation

of ammable vapors. Keep pump assembly in well

ventilated area. Do not spray pump assembly.

8. Do not smoke in the spray area.

9. Do not operate light switches, engines, or similar

spark producing products in the spray area.

10. Keep area clean and free of paint or solvent

containers, rags, and other ammable materials.

11. Know the contents of the paint and solvents being

sprayed. Read all Material Safety Data Sheets

(MSDS) and container labels provided with the

paints and solvents. Follow the paint and solvent

manufacture’s safety instructions.

12. Place pump at least 25 feet (7.62 meters) from the

spray object in a well ventilated area (add more

hose if necessary). Flammable vapors are often

heavier than air. Floor area must be extremely well

ventilated. The pump contains arcing parts that

emit sparks and can ignite vapors.

13. Plastic can cause static sparks. Never hang plastic

to enclose spray area. Do not use plastic drop

cloths when spraying ammable material.

14. Fire extinguisher equipment shall be present and

working.

c) WARNING - To reduce the risk of skin

injection:

1. Do not aim the gun at, or spray any person

or animal.

2. Keep hands and other body parts away from the

discharge. For example, do not try to stop leaks

with any part of the body.

3. Always use the nozzle tip guard. Do not spray

without the nozzle tip guard in place.

4. Only use a nozzle tip specied by the

manufacturer.

5. Use caution when cleaning and changing nozzle

tips. In the case where the nozzle tip clogs while

spraying, ALWAYS lock gun trigger, shut pump

off, and release all pressure before servicing,

cleaning tip or guard, or changing tip. Pressure

will not be released by turning off the motor. The

PRIME/SPRAY valve or pressure bleed valve must

be turned to their appropriate positions to relieve

system pressure. Refer to PRESSURE RELIEF

PROCEDURE described in the pump manual.

6. Do not leave the unit energized or under pressure

while unattended. When the unit is not in use, turn

off the unit and relieve the pressure in accordance

with the manufacturer’s instructions.

7. High-pressure spray is able to inject toxins into

the body and cause serious bodily injury. In the

event that injection occurs, seek medical attention

immediately.

English

8. Check hoses and parts for signs of damage, a leak can

inject material into the skin. Inspect hose before each

use. Replace any damaged hoses or parts.

9. This system is capable of producing 2800 PSI / 193

Bar. Only use replacement parts or accessories that

are specied by the manufacturer and that are rated a

minimum of 2800 PSI. This includes spray tips, nozzle

guards, guns, extensions, ttings, and hose.

10. Always engage the trigger lock when not spraying.

Verify the trigger lock is functioning properly.

11. Verify that all connections are secure before operating

the unit.

12. Know how to stop the unit and bleed pressure quickly.

Be thoroughly familiar with the controls. Pressure will

not be released by turning off the motor. The PRIME/

SPRAY valve or pressure bleed valve must be turned to

their appropriate positions to relieve system pressure.

Refer to PRESSURE RELIEF PROCEDURE described

in the pump manual.

13. Always remove the spray tip before ushing or cleaning

the system.

NOTE TO PHYSICIAN:

Injection into the skin is a traumatic injury. It is

important to treat the injury as soon as possible.

DONOTdelaytreatmenttoresearchtoxicity.

Toxicityisaconcernwithsomecoatingsinjected

directly into the blood stream. Consultation with

a plastic surgeon or reconstructive hand surgeon

may be advisable.

d) WARNING - To reduce the risk of injury:

1. Always wear appropriate gloves, eye protection,

clothing and a respirator or mask when painting.

Hazardous vapors – Paints, solvents, insecticides, and

other materials can be harmful if inhaled or come in

contact with body. Vapors can cause severe nausea,

fainting or poisoning.

2. Do not operate or spray near children. Keep children

away from equipment at all times.

3. Do not overreach or stand on an unstable support.

Keep effective footing and balance at all times.

4. Stay alert and watch what you are doing.

5. Do not operate the unit when fatigued or under the

inuence of drugs or alcohol.

6. Do not kink or over-bend the hose. Airless hose can

develop leaks from wear, kinking and abuse. A leak

can inject material into the skin.

7. Do not expose the hose to temperatures or pressures in

excess of those specied by manufacturer.

8. Do not use the hose as a strength member to pull or lift

the equipment.

9. Use lowest possible pressure to ush equipment.

10. Follow all appropriate local, state and national

codes governing ventilation, re prevention and

operation.

11. The United States Government Safety Standards

have been adopted under the Occupational

Safety and Health Act (OSHA). These standards,

particularly part 1910 of the General Standards and

part 1926 of the Construction Standards should be

consulted.

12. Before each use, check all hoses for cuts, leaks,

abrasion or bulging of cover. Check for damage or

movement of couplings. Immediately replace hose

if any of those conditions exist. Never repair a paint

hose. Replace with a conductive high-pressure

hose.

13. Do not spray outdoors on windy days.

14. Always unplug cord from outlet before working on

equipment (electric models only).

Important Electrical Information

IMPORTANT: Useonlya3-wireextensioncordthat

has a 3-blade grounding plug and a 3-slot receptacle

that will accept the plug on the product. Make sure

yourextensioncordisingoodcondition.When

usinganextensioncord,besuretouseoneheavy

enough to carry the current your product will draw.

An undersized cord will cause a drop in line voltage

resulting in loss of power and overheating. A 14

or 12 gauge cord is recommended (see chart). If

anextensioncordistobeusedoutdoors,itmust

bemarkedwiththesuffixW-Aafterthecordtype

designation.Forexample,adesignationofSJTW-A

would indicate that the cord would be appropriate

for outdoor use.

Cord gauge Maximum cord length

12 150 feet

14 100 feet

Wagner Spray Tech accessory extension cords

recommended:

P/N 0090241 20 foot extension cord

P/N 0090242 35 foot extension cord

Do not use more than 50 feet of spray hose. If you

need to spray further than 50 feet away from your

powersource,usemoreextensioncord,notmore

spray hose.

Ifyouexperienceproblemswithyoursprayerat

any time during assembly, operation, or cleanup,

please refer to the Troubleshooting section of this

manual (page 22), or call customer service at:

1-800-328-8251

Spray

guard

Spray tip

Saddle

seat**

Washer**

Saddle seat and washer

come pre-assembled inside

spray guard

Stand

Button (2)

ON / OFF

switch

Gun hook

Suction extension

(for five-gallon

container setup)

Stand

Spray tip

storage area

Clip

Pump cleaning

adapter

Remove the plug from inside

the hose fitting. Discard.

Remove the cap on the

spray hose outlet. Discard.

(comes assembled

to the spray gun)

Spray gun

Spray tip

assembly

Spray Gun

Spray Tip Assembly

Sprayer Assembly

Spray Hose

Pail bracket

Suction tube

Material

return tube

Inlet filter

Spray hose

outlet

PRIME/SPRAY

knob

Spray hose

holder

English

What’s in

the box?

*Certain parts of the sprayer will not be

assembled out of the box. Be sure to read

Assembly instructions, page 6.

English

Proper

use and

functions

Start

Controls and Functions

ON/OFF switch:

The ON/OFF switch turns power

to sprayer on and off.

(O=OFF, |=ON)

PRIME/SPRAY knob:

The PRIME/SPRAY knob directs

material to the material return

tube when set to PRIME or to

spray hose when set to SPRAY.

Spray hose:

The spray hose connects the

spray gun to the pump.

Pressure control:

The pressure control function is

also controlled by the PRIME/

SPRAY knob. The pressure

control regulates the amount

of force the pump uses to push

the uid and can be adjusted for

desired spray pattern.

Spray gun:

The spray gun controls the

delivery of the material being

pumped.

Trigger lock:

Engage the trigger lock whenever

the gun is not in use.

The gun is locked when the

trigger lock is at a 90º angle

(perpendicular to the trigger in

either direction).

Material return tube (a):

Fluid is sent out through the

return tube and back into the

original container when the

PRIME/SPRAY knob is in the

PRIME position.

Suction tube (b):

The suction tube draws the uid

from the original container into

the pump.

Sprays a variety of paints (oil-based and

latex), primers, stains, preservatives and other

nonabrasive materials. Do not use materials

with ash points below 70° F (21° C)

Do not use!

This pump should not be used with textured

materials, block ller, lacquers, industrial

enamels, or asphalt sealer or materials

containing HHC. See coating supplier if ash

point is not listed on the container

Safety features:

Spray gun trigger lock and pressure diffuser;

built-in tip safety guard; PRIME/SPRAY knob

for safe pressure release. Conforms to ULSTD

1450. Certied to CAN/CSAC 22.2 NO 68-92

Speciﬁcations

Weight ................................20.5 lbs

Flow rate .............................0.24 gal/minute

Power source......................1/2 Hp universal

motor

Power requirement .............15 amp minimum

circuit on 120 VAC,

60 Hz current

Generator requirement .......5000 Watt

Max. spraying pressure ......2800 PSI

Capability:

(a)

(b)

CLEAN ROLLCLEAN ROLL

MAX

SPRAY - MINIMUM

PRESSURE

Ideal for thinner spray

materials.

Also to be used

during cleanup, when

unclogging the tip, or

when using the optional

roller attachment.

SPRAY - MAXIMUM

PRESSURE

Ideal when spraying

thicker materials.

To be used during

spraying.

English

1. Assembly

Start

1. Slowly guide the button housings

over the ends of the stand until

they snap into place.

2. Carefully lay the sprayer on its

back. Insert the suction tube (a)

into the sprayer as shown.

Be sure it is fully inserted.

3. Squeeze the ears of the clip

(b) and place it inside the inlet

tting to hold the suction tube in

place.

Place the sprayer upright again.

You will need:

• Adjustable wrench

IMPORTANT: Do not plug in the

power cord until assembly is

complete.

Note: It will be much easier to

attach the hose to the sprayer if

you uncoil it first.

4. Thread one end of the spray

hose to the outlet valve on the

sprayer.

Tighten the hose with an

adjustable wrench.

5. One gallon setup -

Press the stand buttons and

slide the sprayer down the

stand as far as it will go (it will

lock into place).

Hook the material container on

the pail bracket.

6a. Five-gallon setup -

Press the stand buttons and slide the

sprayer up until it clicks into place.

Unscrew the inlet lter (c) and remove.

Note: You may have to stand on the “feet”

of the stand in order to slide the sprayer up.

6b. Thread the inlet lter into the suction

extension (d).

Thread the suction extension into the

bottom of the suction tube (e).

IMPORTANT: DO NOT attach the bucket

handle to the pail bracket.

(a)

(b)

PRESS

(d)

(e)

PRESS

“FEET”

(c)

6b6a

English

Pressure Relief

Procedure*

*Perform when instructed

Start

Important Safety

Warning

Be sure to follow the Pressure Relief

Procedure when shutting the unit off

for any purpose. This procedure is

used to relieve pressure from the

spray hose. Failure to do so could

result in serious injury.

You will need:

• A waste bucket

Important Safety Warning

Be careful when handling the spray gun so you don’t

accidently spray yourself. The high pressure paint

stream could pierce your skin causing serious injury. If

an accident happens see detail procedures in the Safety

Information section on pages 2-3. See physician

immediately and bring this instruction manual.

1. Lock the spray gun trigger.

3. Turn the PRIME/SPRAY knob to PRIME.

2. Turn the power OFF.

4. Unlock the spray gun. Briey pull the

trigger to fully relieve pressure from the

system. Lock the spray gun.

PRIME

3 4

OFF

English

2. Load

Material

Start

1. Push the red inlet

release button to

ensure proper inlet

valve operation.

4. Hold return tube over

waste bucket until

material is owing

(approximately ve

seconds).

2. Unclip the suction hose and return

tube. Place suction hose into material

container (a). Place return tube into a

waste bucket (b).

5. Turn power OFF.

3. Plug in the sprayer. Turn the

PRIME/SPRAY knob to PRIME.

Turn the power ON.

6. Place return tube into material

container and clip tube and

suction hose together.

You will need:

• The material you plan to spray

• Extension cord

• Waste bucket

PRIME

OFF

(a)

(b)

English

3. Getting

Material to

Flow

Start

You will need:

• Scrap material / cardboard

• Drop cloths to protect oors and

furnishings from overspray

Note: Motor will cycle ON and OFF while

spraying to regulate pressure. This is normal.

1. Rotate spray tip forward to

SPRAY position (a).

Unlock the spray gun trigger.

4. Turn the PRIME/SPRAY

knob to SPRAY - MAXIMUM

PRESSURE.

2. Point the spray gun at a piece

of scrap material/cardboard.

Squeeze and hold trigger

for steps 3-5.

5. Continue to squeeze trigger

until the material is owing

freely through the spray gun.

Note: Motor will cycle ON and

OFF while spraying to regulate

pressure. This is normal.

3. Turn the power ON.

6. Release the trigger and lock

the spray gun.

(a)

MAX

SQUEEZE

SPRAY

English

4. Practice

Spraying

Start

You will need:

• Scrap material / cardboard

Notes:

If the spray pattern becomes distorted or

stops completely while the gun is triggered,

follow any or all the procedures listed on

pages 12-14.

If you plan to be away from your spray

project for more than one hour, follow the

Short Term Storage instructions on page 15.

Ifyouhavedifcultyachievingagoodspray

pattern,yourspraytipandgunltermay

not be ideal for the type of material you are

spraying. Refer to the chart below and on

page 75.

Spray

Tip

Size

Filter

Color

Spray

Material

Initial

Pressure

Setting

411

Red

Thin stains,

sealers

Minimum

511

413

Yellow

Thick latex

paints,

stains

Maximum

513

415

515

Hold the Spray Gun Level

Practice on a piece of scrap material/cardboard

Tip:

Trigger gun after starting the

stroke. Release the trigger

before ending the stroke. The

spray gun should be moving

when the trigger is pulled and

released. Overlap each stroke

by about 30%. This will ensure

an even coating.

10” - 12”

(25 - 30 cm)

10” - 12”

(25 - 30 cm)

CORRECT INCORRECT

English

Spray Pattern Overlap Your Strokes

Spray Technique

8” - 10”

(20 - 25 cm)

GOOD SPRAY PATTERN BAD SPRAY PATTERN: TAILING

CORRECT

See page 12-14

Start

stroke

End

stroke

Pull

trigger

Release

trigger

Move

steadily

CORRECT

INCORRECT

Tip:

Flex your wrist as

you move in order to

keep gun parallel to

the surface

English

Spraying

Troubleshooting -

Clear the

Spray Tip

Start

You will need:

• Scrap material / cardboard

Do not attempt to unclog or

clean the tip with your finger.

High pressure fluid can cause

injection injury.

1. Lock the spray gun. 2. Rotate reversible spray tip 180 degrees

to CLEAN position (arrow pointing

toward the rear of the spray gun).

Note: If spray tip is difcult

to rotate, relieve pressure

by 1) slowly turn PRIME/

SPRAY knob to PRIME, 2)

unlock the spray gun and

3) squeeze trigger while

pointing at scrap material/

cardboard. Release

trigger, lock the spray gun,

and try rotating spray tip

again.

3. Make sure the PRIME/SPRAY

knob is turned to SPRAY -

MINIMUM PRESSURE.

Unlock the spray gun.

4. Point at a piece of scrap material / card-

board and squeeze trigger until material

comes out in a high pressure stream.

Release the trigger and lock the spray

gun.

5. Reverse the spray tip so

the arrow points forward.

Unlock the spray gun and

resume spraying.

1 2

3 4 5

English

Spraying

Troubleshooting -

Clean the Spray

Gun Filter

Start

You will need:

• Wrench

• Warm, soapy water for latex material

• Mineral spirits for oil based materials

• Replacement spray gun lter (if necessary)

IMPORTANT: Never clean the filter by

poking it with a sharp object.

1. Peform the Pressure

Relief Procedure, page 7.

5. Inspect the lter for

damage. Replace if any

holes or tears are found.

4. Remove the lter from the

housing. Clean with appropriate

cleaning solution (warm, soapy

water for latex materials; mineral

spirits for oil-based materials).

2. Pull trigger guard

from lter housing.

6. Replace cleaned lter, tapered

end rst, into the gun housing.

Note: It is important to place tapered

end rst to ensure proper sprayer

operation.

3. Tighten the wrench over the

wrench ats (a). Unscrew the

lter housing using a wrench.

Note: You DO NOT need to

remove the spray hose from the gun

to clean the lter.

7. Reassemble the spray gun.

PRIME

(a)

English

Spraying

Troubleshooting -

Clean the

Inlet Filter

Start

You will need:

• Warm, soapy water for latex material

• Mineral spirits for oil based materials

IMPORTANT: Make sure your floors and

furnishings are covered with drop cloths

to prevent accidental drips.

1. Unscrew the inlet lter from the tting

on the end of the suction tube.

3. Replace the cleaned lter by

threading it back into the tting on the

end of the suction tube.

2. Clean the lter using the appropriate

cleaning solution (warm, soapy

water for latex materials, mineral

spirits for oil-based materials).

Note: If after completing all of the steps

in Spraying Troubleshooting you are still

experiencing problems spraying, refer to

the Troubleshooting section (page 22).

English

Short Term

Storage

Start

English

You will need:

• Water

• Plastic bag or bucket

• Rags

• Stir stick

This procedure should be used when taking

a short term break or when ending your

project for the day. If your break is longer

than 16 hours follow Cleanup instructions,

page 16.

Instructions are for latex

materials only

Note: If using oil based material follow

instructions for Cleanup on page 16.

Shutdown

Startup

1. Peform the Pressure Relief

Procedure, page 7.

1. Remove the spray gun from

the plastic bag or the water.

2. Place spray gun in plastic

bag or immerse into bucket of

water.

2. If water was added during

shut down, stir water into

material with the stir stick.

3. Pour 1/2 cup water slowly on

the top of the paint to prevent

the paint from drying. Place

the entire spraying system out

of the sun.

3. Follow Getting Material to

Flow instructions, page 9.

PRIME

Page 9

FollowthesestepsifyouusedlatexmaterialsAND if

you have a garden hose available.

If you do not have a garden hose available, follow the

Cleanup - Oil-Based Materials instructions on page 18.

English

Cleanup

Start

You will need:

• A water source that can be delivered

with a garden hose (latex materials only)

• Mineral spirits if using oil-based material

• Empty waste container

• A container with warm, soapy water

• When using latex material, clean sprayer and components with warm, soapy water. For oil based

material use mineral spirits. Never use mineral spirits with latex materials

• NEVER use gasoline to clean sprayer

• Dispose of used cleaning solution properly

• Thorough cleaning and lubrication of sprayer is important to ensure proper operation after storage

• If you ush your sprayer with mineral spirits, repeat Cleanup instructions using warm, soapy water.

Follow these steps whenever cleaning with mineral spirits:

• If spraying or cleaning with oil-based materials, the spray gun must be grounded while preparing

the spray hose or cleaning.

• Ground the gun by holding it against the edge of a metal container while purging. Failure to do so

may lead to a static electric discharge which may cause a re.

• Always ush spray gun at least one hose length from spray pump.

• If collecting ushed solvent in one gallon metal container, place it into an empty ve gallon

container, then ush.

• Area must be free from vapors.

• Follow all cleanup instructions.

Cleaning notes - read before cleaning

1. Perform Pressure Relief Procedure

(page 7).

2. Remove the spray tip and

place into container lled

with warm, soapy water.

3. Place the suction tube and return tube

into an empty waste container.

4. Using a garden hose, rinse off the

suction tube, return tube and inlet lter.

Empty the waste container of all uids.

PRIME

3 4

MINERAL

SPIRITS

STOP

English

5. Remove the inlet lter from

the suction tube and place

it into waste container.

6. Thread pump cleaning

adapter onto garden hose.

Thread suction tube tting

over the adapter.

7. Unclip the return tube from the suction tube

and place it into the waste container.

Turn the PRIME/SPRAY knob to PRIME.

8. Turn the water supply to the garden hose on.

Turn the pump ON.

Water will go into the suction tube and out

through the return tube. Let the pump run

for a few minutes, and leave pump running

for next steps.

9. Point the spray gun at the side of

a waste container.

10. While squeezing the trigger, turn the

PRIME/SPRAY knob to SPRAY -

MINIMUM PRESSURE.

11. Continue squeezing the trigger

until uid is coming out clear.

12. Perform Pressure Relief

Procedure, page 7.

Move on the Cleaning the Spray

Gun Components, page 19.

5 6 7 8

PRIME

10 11 12

PRIME

English

Cleanup -

Oil-Based

Materials

Start

You will need:

• Mineral spirits if using oil-based material

• Warm, soapy water if using latex material

• Waste container

Follow these steps if you sprayed oil-based

materials,orifyousprayedlatexmaterials

and do not have a garden hose available.

Be sure to use the appropriate cleaning

solution for the type of material sprayed.

1. Perform Pressure Relief

Procedure (page 7).

5. While squeezing the

trigger, turn the power

ON, and turn the PRIME/

SPRAY knob to SPRAY -

MINIMUM PRESSURE.

4. Point the spray gun at the side of

a waste container. Ground the

gun against the side of a metal

wastecontainerifushing

with mineral spirits.

2. Remove the spray tip

and place into an empty

waste container.

6. Continue squeezing the trigger

until uid is coming out clear.

You may need to get new

cleaning solution.

3. Submerge suction set into a

bucket with the appropriate

cleaning solution.

7. Perform Pressure Relief

Procedure, page 7.

Ifyouushedthesprayerwithmineral

spirits repeat the steps on this page

using warm, soapy water.

PRIME

English

Cleaning the

Spray Gun

Components

Start

You will need:

• Soft bristled brush

• Multi-Purpose Oil

• Warm, soapy water if using latex material

• Mineral spirits for oil based material

• Wrench

1. Peform the Pressure

Relief Procedure, page 7.

5. Install gun lter tapered-

end rst. Reassemble

spray gun.

4. Pour a few drops of Multi-

Purpose Oil inside gun housing.

2. Pull trigger guard to separate

from lter housing and unscrew

housing using a wrench.

Note: Tighten the wrench over the

wrench ats (a).

6. Install spray tip with arrow

pointing towards front of

spray guard tip.

3. Remove lter from spray gun.

Clean spray tip and lter with soft

bristled brush and appropriate

cleaning solution.

7. Install spray tip and guard

assembly.

Move on to Long Term

Storage, page 20.

PRIME

(a)

MULTI-PURPOSE

OIL

English

Long Term

Storage

Start

You will need:

• Multi-Purpose Oil

• Rags

IMPORTANT: Store the

unit indoors with the

power cord wrapped

around the cord holder.

1. Carefully tilt the sprayer on

its back.

Squeeze the ears (a) on

the suction tube clip and

slide out of the inlet tting.

5. Turn power OFF. 4. Cover the outlet valve with a rag.

Turn power ON and let the pump

run for ve seconds.

2. Remove the suction tube.

Using a wrench, remove

the spray hose.

6. Replace suction tube. Insert

suction tube into the inlet valve

housing and secure with the

suction tube clip (b).

3. Careully tilt the sprayer upside-down.

Squirt approximately 2 ounces of Multi-

Purpose Oil into the inlet tting.

7. Wipe entire unit, hose,

and spray gun to remove

accumulated spray material.

MULTI-PURPOSE

OIL

(a)

(b)

MULTI-PURPOSE

OIL

OFF

5 SECONDS

La page charge ...

WAGNER PROCOAT MAX Le manuel du propriétaire

Marque: WAGNER

Modèle: PROCOAT MAX

Catégorie: Systèmes de pulvérisation fine Power

Taper: Le manuel du propriétaire

Ce manuel convient également à

ProCoat Plus

Télécharger le PDF

rapport

dans d''autres langues

English: WAGNER PROCOAT MAX Owner's manual

WAGNER PROCOAT MAX Le manuel du propriétaire

Ce manuel convient également à

WAGNER PROCOAT MAX Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents