Develco Products H6500113 Guide d'installation

H6500113
Marque
Develco Products
Modèle
H6500113
Taper
Guide d'installation
eng
Getting started
1. Open the casing of the device by removing
the screw at the bottom of the device.
2. Use the included screws to mount the back
plate of the device on the wall
4. Insert batteries into the device respecting
the polarities.
5. When the batteries are inserted, the Keypad
will start searching (up to 15 minutes) for a
Zigbee network to join. While the Keypad is
searching for a Zigbee network to join, the
yellow LED ashes.
6. If the scanning has timed out, a short press
on the menu button inside the device will
restart it.
7. After connecting the device to a network,
attach the device to the back plate by
hooking the device to the top of the back
plate and pushing the device against the
back plate.
Battery replacement
CAUTION:
• Do not attempt to recharge or open the
batteries.
• Risk of explosion if batteries are replaced by
an incorrect type.
• Dispose of a battery into re or a hot oven, or
mechanically crushing or cutting of a battery
can result in an explosion
• Leaving a battery in an extremely high
temperature surrounding environment can
result in an explosion or the leakage of
ammable liquid or gas.
• A battery subjected to extremely low air
pressure may result in an explosion or the
leakage of ammable liquid or gas
• Maximum operation temperature is 50°C /
122°F
• If you experience leakage from the batteries,
immediately wash your hands and/or any
aected area of your body thoroughly!
CAUTION: When removing cover for battery
change - Electrostatic Discharge (ESD) can
harm electronic components inside.
1. To replace the batteries, remove the screw
at the bottom of the device and open the
casing.
2. Replace all four batteries inside the device,
respecting the polarities.
3. Reattach the device to the backplate and
reinsert the screw at the bottom of the
device
a.
b.
d.
e.
f.
g
c.
8. Finally, reinsert the screw at the bottom of
the device
Resetting
Resetting is needed if you want to connect
your Keypad to another gateway or if you need
to perform a factory reset to avoid abnormal
behavior.
STEPS FOR RESETTING
1. Open the casing of the device by removing
the screw at the bottom of the device.
2. Press and hold the menu button inside the
device with a thin pin – e.g. a paper clip.
Placement
• You can place the Keypad both indoors and
outdoors in 0-50 degrees °C.
• Place the device, so it is easily accessible to
users.
• Avoid placing the device in direct sunlight.
• Avoid placing the device in places exposed
to direct rain.
• Avoid placing moving items 40 cm or less
from the Keypad, as they will activate the
presence sensor.
• When mounting the device outdoors, use
screws rather than tape.
Precautions
• Do not remove the product label as it
contains important information.
• Be aware that electronics are sensitive
to static electricity, so aim to discharge
before touching, and avoid touching any
components inside the device.
• Do not paint the device.
• Do not use tape for mounting the device
outdoors.
• Do not use tape for mounting if you will use
the device for security purposes, as the
tamper switch will not function.
• When mounting with tape, make sure the
surfaces are clean and dry.
• When mounting with tape, the room
temperature should ideally be between 21°
C and 38° C and minimum 16° C.
• Avoid mounting with tape on rough, porous
or bered materials such as wood or
cement, as they reduce the tape bond.
Product description
The Keypad includes a tag reader and allows
you to enable and disable an alarm system.
The Keypad detects when a person is within
operating distance, which will make it light up in
the dark. The Keypad includes a tamper switch,
making it ideal for security purposes.
Version 2.4
INSTALLATION MANUAL
Keypad
3. While you are holding the button down, the
LED rst ashes once, then two times in a
row, and nally numerous times in a row.
4. Release the button while the LED is ashing
numerous times in a row.
5. After you release the button, the LED shows
one long ash, and the reset is completed.
3. Alternatively, you can use the double
adhesive tape to mount the backplate. Make
sure to press rmly on the backplate with
the tape to make it stick.
Disclaimers
CAUTION:
• Choking hazard! Keep away from children.
Contains small parts.
• Please follow the guidelines thoroughly. The
Keypad is a preventive, informing device,
not a guarantee or insurance that sucient
warning or protection will be provided, or
that no property damage, theft, injury, or
any similar situation will take place. Develco
Products cannot be held responsible in
case any of the above-mentioned situations
occur.
H6500113 Keypad installation manual, v2.4.indd 1H6500113 Keypad installation manual, v2.4.indd 1 10/7/2021 11:56:15 AM10/7/2021 11:56:15 AM
Other certications
Zigbee 3.0 certied
Disposal
Dispose the product and batteries properly at
the end of their lives. This is electronic waste
which should be recycled.
Develco Products assumes no responsibility for
any errors, which may appear in this manual.
Furthermore, Develco Products reserves the
right to alter the hardware, software, and/
or specications detailed herein at any time
without notice, and Develco Products does
not make any commitment to update the
information contained herein. All the trademarks
listed herein are owned by their respective
owners.
Distributed by Develco Products A/S
Tangen 6
8200 Aarhus
Denmark
Copyright © Develco Products A/S
All rights reserved.
IN ACCORDANCE WITH THE DIRECTIVES
• Radio Equipment Directive (RED) 2014/53/
EU
• RoHS Directive 2015/863/EU amending
2011/65/EU
• REACH 1907/2006/EU + 2016/1688
CE certication
The CE mark axed to this product conrms
its compliance with the European Directives
which apply to the product and, in particular, its
compliance with the harmonized standards and
specications.
FCC statement
Changes or modications to the equipment not
expressly approved by the party responsible for
compliance could void the user’s authority to
operate the equipment.
NOTE: This equipment has been tested and
found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference
to radio communications. However, there is no
guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful
interference to radio or television reception,
which can be determined by turning the
equipment o and on, the user is encouraged
to try to correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an outlet on
a circuit dierent from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/
TV technician for help.
This device complies with FCC RF radiation
exposure limits set forth for an uncontrolled
environment. The antenna used for this
FCC statement
English
This device contains licence-exempt
transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic
Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two
conditions:
1. This device may not cause interference.
2. This device must accept any interference,
including interference that may cause
undesired operation of the device.
This equipment complies with IC RSS-102
radiation exposure limits set forth for an
uncontrolled environment. This equipment
should be installed and operated with minimum
distance 20 cm between the radiator and your
body.
Français
L’émetteur/récepteur exempt de licence
contenu dans le présent appareil est
conforme aux CNR d’Innovation, Sciences
et Développement économique Canada
applicables aux appareils radio exempts de
licence. L’exploitation est autorisée aux deux
conditions suivantes :
1. L’appareil ne doit pas produire de brouillage;
2. L’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage
est susceptible d’en compromettre le
fonctionnement.
Cet équipement est conforme aux limites
IC statement
ISED statement
Innovation, Science and Economic
Development Canada ICES-003 Compliance
Label: CAN ICES-3 (B)/NMB-3(B).
ISED statement
Fault nding and cleaning
• In case of a bad or wireless weak signal,
change the location of the device. Otherwise
you can relocate your gateway or strengthen
the signal with a smart plug.
• If the search for a gateway has timed out, a
short press on the button will restart it.
transmitter must be installed to provide a
separation distance of at least 20 cm from
all persons and must not be co-located or
operating in conjunction with any other antenna
or transmitter.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interfer-
ence, and
2. this device must accept any interference
received, including interference that may
cause undesired operation.
d’exposition aux radiations IC CNR-102 établies
pour un environnement non contrôlé. Cet
équipement doit être installé et utilisé avec une
distance minimale de 20 cm entre le radiateur
et votre corps.
H6500113 Keypad installation manual, v2.4.indd 2H6500113 Keypad installation manual, v2.4.indd 2 10/7/2021 11:56:15 AM10/7/2021 11:56:15 AM
  • Page 1 1
  • Page 2 2

Develco Products H6500113 Guide d'installation

H6500113
Marque
Develco Products
Modèle
H6500113
Taper
Guide d'installation
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents