COOSPO HW9 Manuel utilisateur

HW9
Marque
COOSPO
Modèle
HW9
Catégorie
Moniteurs de fréquence cardiaque
Taper
Manuel utilisateur
HW9-RTN-I1-2317
ALL ABOUT PASSION
SCAN for more
詳しくはこちら
Cerca altro
Nach mehr SUCHEN
SCANNEZ pour plus
ESCANEAR para más
USER MANUAL
Armband Heart Rate Monitor
- 2 -
34
5
Optical Sensor
Charging Terminals
1
2
LED
Power on/off button
Wearing
- 3 -
Wear the armband on the upper forearm or on the inner or outer side of
the upper arm ③.
2.
Remove the transparent cover ⑤ from the back of HW9.
1.
Adjust the armband to a comfortable length so it stays close to the skin.
This will prevent it from sliding or coming loose during intense exercise
and ensure accurate heart rate monitoring.
Note: Please do not wear it on your wrist ④.
3.
Function and Operation
Heart Rate Zone* Breathing Light ColorIntensity
Zone 1(<60% MHR) Very Light
Zone 2(60%-70% MHR) Light
Zone 3(70%-80% MHR) Moderate
Zone 4(80%-90% MHR) Hard
Zone 5(90%-100% MHR) Maximum
Power on: Short press button ② Light blue LED fast blink and vibrate.
Power off: Long press the button for 2 seconds. LED light will flash red and
vibrate.
After powering on, Light blue LED ① fast blink, indicating that the device
has not detected the heart rate.
After the heart rate is detected, LED light ① can display the heart rate
zone.
Note: The heart rate zone is calculated based on the maximum heart
rate(MHR).
Recommended MHR Calculation: 220 minus your age.
The default MHR value is 200 bpm and can be set in the
CoospoRide/Heartool app.
Low Battery Alert & Charging
Power<10%, Red LED slow blink for 10 seconds and remind the user
every 5 minutes;
Power<1%, Red LED flash, device vibrate and turn off automatically.
Green LED flashes: Charging
Green LED is always on: Charging completed
Charging time is about 1.5 hours.
Note: To extend battery life, please use a DC 5V power adapter or a
computer USB port for charging.
Connect to Device
- 4 -
Connect to Sports and Fitness app (Bluetooth)
Turn on the Bluetooth on your phone.
Find the Sensor Settings Menu in the Sports & Fitness app. Take
CoospoRide and Heartool app as example.
Go to CoospoRide app > More > Sensors > Heart Rate
Or go to Heartool app > Settings > Device > Add Device
Find the HW9 Bluetooth ID and select it in the app to connect.
Note: Do not pair the sensor in the Bluetooth settings of your phone.
Connect to smart devices, including fitness equipment and sports watches
(Bluetooth and ANT+)
1. Select "Add HR sensor" from the smart device settings menu.
Connecting the USB magnetic power cable to the device and the power
source;
2. Find the Bluetooth or ANT+ ID for HW9 and select it to connect.
While the device is working, short press the button to check its Bluetooth
connection status:
Note: The information about sensor compatibility and connection
instructions, please refer to: www.coospo.com/faq/hw9.
Bluetooth is not connected: LED light flashes green.
Bluetooth is connected: LED light flashes blue.
1.
2.
3.
2.
1.
Specifications
Size
Battery Life 35 Hours
Working Temperature Range 0℃~60℃(-4°~140℉)
Charging Temperature Range 10℃~45℃(32°~113℉)
10.6 g（sensor only）
Weight
Bluetooth 5.0 & ANT+
Wireless Transmission
Rechargeable Lithium Battery
Battery Type
41.3 x 33.8 x 11 mm
IP67Waterproof
- 5 -
Connecting the USB magnetic power cable to the device and the power
source;
Website: www.coospo.com E-mail: [email protected]
Standard Accessories
User Manual x1
Heart Rate Monitor with Armband x1
Charging Cable x1
Disclaimer
Contact us
The information contained in this manual just for reference. The
product described above may be subject to alteration owing to the
manufacturer's continuing research and development plans, without
making an announcement in advance.
We shall not bare any legal responsibility for any direct or indirect,
accidental or special damages, losses and expenses arising from or in
connection with this manual or the contained product.
This product is for sports purposes only and it's not meant
to replace any medical device.
- 6 -
FCC statement
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of
the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
(1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- 7 -
Waste electrical products should not be disposed of with household
waste. Please recycle where facilities exist. Contact your local
government or a retailer for additional information.
Do not open or modify the product.
Do not disassemble or attempt to service this product.
This product is safe under normal and reasonably foreseeable
operating conditions.
If product is operating improperly, call COOSPO support.
IC WARNING
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada' s
licence-exempt RSS(s). Operation is subject to the following two conditions:
L' émetteur/récepteur exempt de licence contenu dans le présent appareil
est conforme aux CNR d' Innovation, Sciences et Développement
économique Canada applicables aux appareils radio exempts de licence.
L' exploitation est autorisée aux deux conditions suivantes :
This device may not cause interference.
This device must accept any interference, including interference that
may cause undesired operation of the device.
L' appareil ne doit pas produire de brouillage;
L' appareil doit accepter tout brouillage radioélectrique subi, même si
le brouillage est susceptible d' en compromettre le fonctionnement.
(1)
(2)
(1)
(2)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

COOSPO HW9 Manuel utilisateur

HW9
Marque
COOSPO
Modèle
HW9
Catégorie
Moniteurs de fréquence cardiaque
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Autres documents