Pioneer LX508D Le manuel du propriétaire

Operating Instructions | Mode d’emploi | Bedienungsanleitung

PLASMA TELEVISION

TÉLÉVISEUR PLASMA

PLASMA-FERNSEHER

6080

PDP-LX

D

5080

PDP-LX

D

508

PDP-LX

D

608

PDP-LX

D

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

The lightning flash with arrowhead symbol,

within an equilateral triangle, is intended to

alert the user to the presence of uninsulated

“dangerous voltage” within the product’s

enclosure that may be of sufficient

magnitude to constitute a risk of electric

shock to persons.

CAUTION:

TO PREVENT THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR

BACK). NO USER-SERVICEABLE PARTS

INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

IMPORTANT

D3-4-2-1-1_En-A

Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified

service personnel.

IMPORTANT: THE MOULDED PLUG

This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 13 amp fuse is fitted in this plug. Should the

fuse need to be replaced, please ensure that the replacement fuse has a rating of 13 amps and that it is approved by ASTA or BSI to BS1362.

Check for the ASTA mark or the BSI mark on the body of the fuse.

If the plug contains a removable fuse cover, you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover the plug

must not be used until a replacement cover is obtained. A replacement fuse cover can be obtained from your local dealer.

If the fitted moulded plug is unsuitable for your socket outlet, then the fuse shall be removed and the plug cut off and disposed of

safely. There is a danger of severe electrical shock if the cut off plug is inserted into any 13 amp socket.

If a new plug is to be fitted, please observe the wiring code as shown below. If in any doubt, please consult a qualified electrician.

WARNING : THIS APPARATUS MUST BE EARTHED.

IMPORTANT: The wires in this mains lead are coloured in accordance with the following code:

Green & Yellow : Earth Blue : Neutral Brown : Live

As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in

your plug, proceed as follows ;

The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked with the letter E or

by the earth symbol or coloured GREEN or GREEN-AND-YELLOW.

The wire which is coloured BLUE must be connected to the terminal which is marked with the

letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the terminal which is marked with the

letter L or coloured RED.

How to replace the fuse: Open the fuse compartment with a screwdriver and replace the fuse.

D3-4-2-1-2-1_B_En

If you want to dispose this product, do not mix it with general household waste. There is a separate collection system for used

electronic products in accordance with legislation that requires proper treatment, recovery and recycling.

Private households in the member states of the EU, in Switzerland and Norway may return their used electronic products free of charge to

designated collection facilities or to a retailer (if you purchase a similar new one).

For countries not mentioned above, please contact your local authorities for the correct method of disposal.

By doing so you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential

negative effects on the environment and human health.

K058_A_En

English

WARNING

This equipment is not waterproof. To prevent a fire

or shock hazard, do not place any container filed

with liquid near this equipment (such as a vase or

flower pot) or expose it to dripping, splashing, rain

or moisture.

D3-4-2-1-3_A_En

The following symbols are found on labels attached

to the product. They alert the operators and service

personnel of this equipment to any potentially

dangerous conditions.

This product complies with the Low Voltage Directive

2006/95/EC and EMC Directive 2004/108/EC.

WARNING

This product equipped with a three-wire grounding

(earthed) plug - a plug that has a third (grounding)

pin. This plug only fits a grounding-type power

outlet. If you are unable to insert the plug into an

outlet, contact a licensed electrician to replace the

outlet with a properly grounded one. Do not

defeat the safety purpose of the grounding plug.

D3-4-2-1-6_A_En

WARNING

The voltage of the available power supply differs

according to country or region. Be sure that the

power supply voltage of the area where this unit

will be used meets the required voltage (e.g., 230 V

or 120 V) written on the rear panel.

D3-4-2-1-4_A_En

Before plugging in for the first time, read the following

section carefully.

CAUTION

The  switch on this unit will not completely shut off

all power from the AC outlet. Since the power cord

serves as the main disconnect device for the unit,

you will need to unplug it from the AC outlet to shut

down all power. Therefore, make sure the unit has

been installed so that the power cord can be easily

unplugged from the AC outlet in case of an

accident. To avoid fire hazard, the power cord should

also be unplugged from the AC outlet when left

unused for a long period of time (for example, when

on vacation).

D3-4-2-2-2a_A_En

WARNING

CAUTION

This symbol refers to a hazard or unsafe practice

which can result in personal injury or property

damage.

This symbol refers to a hazard or unsafe practice

which can result in severe personal injury or death.

VENTILATION CAUTION

When installing this unit, make sure to leave space

around the unit for ventilation to improve heat

radiation. For the minimum space required, see

page 15.

WARNING

Slots and openings in the cabinet are provided for

ventilation to ensure reliable operation of the

product, and to protect it from overheating. To

prevent fire hazard, the openings should never be

blocked or covered with items (such as

newspapers, table-cloths, curtains) or by operating

the equipment on thick carpet or a bed.

STANDBY/ON Button

STANDBY:

When placed into the standby mode,

the main power flow is cut and the unit is no

longer fully operational.

STANDBY/ON Indicator: The indicator is lit red

when the unit is in the standby mode and is lit blue

when it is in the power-on mode.

Operating Environment

Operating environment temperature and humidity:

+0 ˚C to +40 ˚C (+32 ˚F to +104 ˚F); less than 85 %RH

(cooling vents not blocked)

Do not install this unit in a poorly ventilated area, or in

locations exposed to high humidity or direct sunlight (or

strong artificial light)

D3-4-2-1-7c_A_En

WARNING

To prevent a fire hazard, do not place any naked

flame sources (such as a lighted candle) on the

equipment.

D3-4-2-1-7a_A_En

page 15

Contents

4

En

Thank you for buying this Pioneer product.

Please read through these operating instructions so you will know how to operate your model properly. After you

have finished reading the instructions, put them away in a safe place for future reference.

In some countries or regions, the shape of the power plug and power outlet may sometimes differ from that shown

in the explanatory drawings. However the method of connecting and operating the unit are the same.

Contents

01 Important user information . . . . . . . . . 6

02 Safety precautions . . . . . . . . . . . . . . . . . 9

Installation precautions. . . . . . . . . . . . . . . . . . . . . . . . .10

03 Supplied accessories . . . . . . . . . . . . . . 11

04 Part names . . . . . . . . . . . . . . . . . . . . . . 12

Plasma television. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Remote control unit. . . . . . . . . . . . . . . . . . . . . . . . . . . .14

05 Preparation . . . . . . . . . . . . . . . . . . . . . . 15

Installing the plasma television . . . . . . . . . . . . . . . . . .15

Moving the plasma television . . . . . . . . . . . . . . . . . . . .15

Preventing the plasma television from falling over. . .16

Basic connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Preparing the remote control unit . . . . . . . . . . . . . . . .19

Operating range of the remote control unit . . . . . . . .19

06 Watching TV . . . . . . . . . . . . . . . . . . . . . 20

Turning the power on . . . . . . . . . . . . . . . . . . . . . . . . . .20

Placing the system into standby . . . . . . . . . . . . . . . . .20

Changing channels . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Tuning to your favourite (analogue) channels. . . . . . .21

Changing the volume and sound . . . . . . . . . . . . . . . . .22

Switching the broadcast audio channel . . . . . . . . . . .22

Use the multiscreen functions . . . . . . . . . . . . . . . . . . .23

Freezing images. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

07 The HOME MENU . . . . . . . . . . . . . . . . . 25

HOME MENU overview . . . . . . . . . . . . . . . . . . . . . . . . .25

Using the HOME MENU . . . . . . . . . . . . . . . . . . . . . . . .26

08 Setting up. . . . . . . . . . . . . . . . . . . . . . . 27

Setting up TV channels . . . . . . . . . . . . . . . . . . . . . . . . .27

Setting up analogue TV channels manually . . . . . . . .27

Reducing video noise . . . . . . . . . . . . . . . . . . . . . . . . . .28

Setting Child Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Selecting a decoder input terminal . . . . . . . . . . . . . . .28

Labeling TV channels . . . . . . . . . . . . . . . . . . . . . . . . . .29

Sorting preset TV channels. . . . . . . . . . . . . . . . . . . . . .29

Language setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

AV Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

Basic picture adjustments . . . . . . . . . . . . . . . . . . . . . .31

Advanced picture adjustments . . . . . . . . . . . . . . . . . .32

Comparing picture adjustments on the screen . . . . .35

Sound adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Listening to audio from the sub screen using

headphones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

Power Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

09 Enjoying DTV broadcasts . . . . . . . . . . 39

Watching DTV programmes . . . . . . . . . . . . . . . . . . . . .39

Reconfiguring the DTV channel settings. . . . . . . . . . .40

Customizing channel related settings . . . . . . . . . . . . .41

Selecting a digital audio format . . . . . . . . . . . . . . . . . .43

Selecting languages for audio, subtitles,

and teletext. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

Using Software Update . . . . . . . . . . . . . . . . . . . . . . . . .43

Screen Saver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

Common Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

Illustrations shown in this manual are for the PDP-LX508D/PDP-LX5080D unless otherwise specified.

Contents

5

En

English

10 Using the Electronic Programme Guide

(EPG)(for DTV only). . . . . . . . . . . . . . . . 46

EPG display format. . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Using the EPG. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Presetting TV programmes using the EPG . . . . . . . . 47

Using other useful EPG functions . . . . . . . . . . . . . . . 50

11 Useful adjustment settings . . . . . . . . . 51

Switching the vertical drive mode

(AV source only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Adjusting image positions (AV source only) . . . . . . . 51

Adjusting image positions and clock automatically

(PC source only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Adjusting image positions and clock manually

(PC source only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Selecting an input signal type. . . . . . . . . . . . . . . . . . . 52

Colour system setting . . . . . . . . . . . . . . . . . . . . . . . . . 53

Selecting a game mode. . . . . . . . . . . . . . . . . . . . . . . . 53

Selecting a screen size manually . . . . . . . . . . . . . . . . 53

Selecting a screen size automatically . . . . . . . . . . . . 54

Detecting side masks. . . . . . . . . . . . . . . . . . . . . . . . . . 54

Changing the brightness at both sides of the screen

(Side Mask) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Room Light Sensor. . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Blue LED Dimmer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Orbiter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Video Pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Using a password. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

12 Using with other equipment . . . . . . . 58

Connecting a DVD player . . . . . . . . . . . . . . . . . . . . . . 58

Connecting a decoder . . . . . . . . . . . . . . . . . . . . . . . . . 58

Connecting a VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Using the SCART output function . . . . . . . . . . . . . . . 59

Switching the SCART output. . . . . . . . . . . . . . . . . . . . 60

Connecting a game console or camcorder . . . . . . . . 60

Connecting a personal computer . . . . . . . . . . . . . . . . 61

Connecting an amplifier/AV receiver . . . . . . . . . . . . . 61

Using the HDMI Input . . . . . . . . . . . . . . . . . . . . . . . . . 62

Connecting control cords . . . . . . . . . . . . . . . . . . . . . . 64

Using i/o link.A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Enjoying through USB interface (Home Gallery

function) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Controlling other equipment using the supplied

remote control unit. . . . . . . . . . . . . . . . . . . . . . . . . . 69

13 Using the HDMI Control . . . . . . . . . . . 74

Using the HDMI Control functions. . . . . . . . . . . . . . . 74

Making the HDMI Control connections . . . . . . . . . . . 75

Setting the HDMI Control . . . . . . . . . . . . . . . . . . . . . . 77

Using the HDMI Control menus . . . . . . . . . . . . . . . . . 79

14 Using Teletext . . . . . . . . . . . . . . . . . . . 80

Using the Teletext Functions. . . . . . . . . . . . . . . . . . . . 80

Operating the Teletext basics . . . . . . . . . . . . . . . . . . . 80

15 Additional information. . . . . . . . . . . . 82

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

Signal names for 15-pin mini D-sub connecter. . . . . 84

SCART pin assignments . . . . . . . . . . . . . . . . . . . . . . . 85

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

Important user information01

6

En

Chapter 1

Important user information

In order to obtain maximum enjoyment from this Pioneer

PDP-LX608D/PDP-LX6080D/PDP-LX508D/PDP-LX5080D plasma

television, please first read this information carefully.

With the Pioneer PDP-LX608D/PDP-LX6080D/PDP-LX508D/PDP-

LX5080D, you can be assured of a high quality plasma television

with long-life and high reliability. To achieve images of exceptional

quality, this Pioneer plasma television incorporates state-of-the-art

design and construction, as well as very precise and highly

advanced technology.

The Pioneer PDP-LX608D/PDP-LX6080D/PDP-LX508D/PDP-

LX5080D plasma television incorporates the latest in colour filter

technology: Direct Colour Filter. This improves the colour /picture

reproduction of these models as compared to previous models. It

also eliminates the need for a physical glass panel to be placed in

front of the plasma display, which furthers Pioneer’s continued goal

of reducing environmental waste in consumer electronics, now

during the manufacturing process and in the future during the

recycling process.

Over the course of its lifetime, the luminosity of the Pioneer

PDP-LX608D/PDP-LX6080D/PDP-LX508D/PDP-LX5080D plasma

television will diminish very slowly, such as with all phosphor-based

screens (for example, a traditional tube-type television). To enjoy

beautiful and bright images on your Pioneer plasma television for a

long time, please carefully read and follow the usage guidelines

below:

Usage guidelines

All phosphor-based screens (including conventional tube-type

televisions) can be affected by displaying static images for a

prolonged period. Plasma televisions are no exception to this rule.

After-image and permanent effects on the screen can be avoided by

taking some basic precautions. By following the recommendations

listed below, you can ensure longer and satisfactory results from

your plasma television:

• Whenever possible, avoid frequently displaying the same image

or virtually still moving pictures (e.g. closed-captioned images

or video game images which have static portions).

• Do not display Teletext for a prolonged period of time.

• Avoid viewing the on-screen display for extended periods, from

a decoder, DVD player, VCR and all other components.

• Do not leave the same picture freeze-framed or paused

continuously over a long period of time, when using the still

picture mode from a TV, VCR, DVD player or any other

component.

• Images which have both very bright areas and very dark areas

side by side should not be displayed for a prolonged period of

time.

• When playing a video game, the “GAME” mode setting within

“AV Selection” is strongly recommended. However, please do

not use this mode for long periods of time.

• After playing a game or displaying any still image, it is best to

view a normal moving picture in the “WIDE” or “FULL” screen

setting for more than three times the length of the previous still/

moving image.

• After using the plasma television, always switch the display to

“STANDBY” mode.

Installation guidelines

The Pioneer PDP-LX608D/PDP-LX6080D/PDP-LX508D/PDP-

LX5080D plasma television incorporates a very thin design. To

ensure safety, please take the proper measures to mount or install

the plasma television, in order to prevent the unit from tipping over

in the event of vibration or accidental movement.

This product should be installed by using only parts and

accessories designed by Pioneer. Use of accessories other than the

Pioneer stand or installation bracket may result in instability, and

could cause injury. For custom installation, please consult the

dealer where the unit was purchased. To ensure correct installation,

experienced and qualified experts must install the unit.

Pioneer will not be responsible for accident or damage caused by

the use of parts and accessories manufactured by other

companies, inadequate installation or stabilization, erroneous

operation, remodeling or natural disasters.

To avoid malfunction and overheating, make sure that the vents on

the main unit are not blocked when installing to ensure proper heat

emission:

• Distance the unit slightly from other equipment, walls, etc. For

the minimum space required around the unit, see page 15.

• Do not fit the unit inside narrow spaces where ventilation is

poor.

• Do not cover with a cloth, etc.

• Clean the vents on the sides and rear of the unit to remove dust

build-up, by using a vacuum cleaner set to its lowest suction

setting.

• Do not place the product on a carpet or blanket.

• Do not leave the product tilted over.

• Do not turn the product upside down.

Using the unit without proper ventilation may cause the internal

temperature to rise, and could result in possible malfunction. When

the surrounding or internal temperature exceeds a certain degree,

the display will automatically power off in order to cool the internal

electronics and prevent hazardous occurrences.

Any malfunction may occur due to: an inappropriate installation

site, improper assembly, installation, mounting, or operation of this

product, modifications made to the product. However, Pioneer

cannot be held responsible for such accidents or malfunction.

Note

The following are typical effects and characteristics of a

phosphor-based matrix display and as such, are not covered by

the manufacturer’s limited warranties:

• Permanent residual images upon the phosphors of the panel.

• The existence of a minute number of inactive light cells.

• Panel generated sounds, examples: Fan motor noise, and

electrical circuit humming/glass panel buzzing

Important user information 01

7

En

English

Caution

• Pioneer bears no responsibility for any damage arising from

incorrect use of the product by you or other people,

malfunctions when in use, other product related problems, and

use of the product except in cases where the company must be

liable.

Plasma television protection function

When still images (such as photos and computer images) stay on

the screen for an extended period of time, the screen will be slightly

dimmed. This is because the protection function of the plasma

television automatically adjusts the brightness to protect the screen

when detecting still images; so this does not designate

malfunction. The screen is dimmed when a still image is detected

for about three minutes.

Information of pixel defect

Plasma television displays information using pixels. Pioneer

plasma television panels contain a very large number of pixels.

(Depending on the panel size; over 3.1 million pixels for a 50 inch/60

inch display). All Pioneer display panels are manufactured using a

very high level of ultra-precision technology and undergo individual

quality control.

In rare cases, some pixels can be permanently switched off, or on,

resulting in either a black or coloured pixel permanently fixed on the

screen.

This effect is common to all plasma televisions because it is a

consequence of the technology.

If the defective pixels are visible at a normal viewing distance of

between 2.5 meters and 3.5 meters whilst viewing a normal

broadcast (i.e. not a test card, still image or single colour display)

please contact the supplying dealer.

If, however, they can only be seen close up or during single colour

displays then this is considered normal for this technology.

Infrared rays

The plasma television releases infrared rays because of its

characteristics. Depending on how the plasma television is used,

the remote controls of nearby equipment may be adversely affected

or wireless headphones using infrared rays are interfered by noise.

If this is the case, place that equipment at a location where its

remote control sensor is not affected.

Radio interference

While this product meets the required specifications, it emits a

small amount of noise. If you place such equipment as an AM radio,

personal computer, and VCR close to this product, that equipment

may be interfered. If this happens, place that equipment far enough

from this product.

Plasma television driving sound

The screen of the plasma television is composed of extremely fine

pixels and these pixels emit light according to received video

signals. This principle may make you hear buzz sound or electrical

circuit humming from the plasma television.

Do not attach such items as labels and tape to the

product

This may result in the discolouration or scratch of the cabinet.

When not using the product for a long period of time

If you do not use the product for a long period of time, the functions

of the product may be adversely affected. Switch on and run the

product occasionally.

Condensation

Condensation may take place on the surface or inside of the

product when the product is rapidly moved from a cold place to a

warm place or just after a heater is switched on in winter morning,

for example. When condensation takes place, do not switch on the

product and wait until condensation disappears. Using the product

with condensation may result in malfunction.

Cleaning the surface of the screen and the glossy

surface of the front cabinet

When cleaning the surface of the screen or the glossy surface of the

front cabinet, gently wipe it with a dry soft cloth; the supplied

cleaning cloth or other similar cloths (e.g., cotton and flannel). If

you use a dusty or hard cloth or if you rub the screen hard, the

surface of the product will be scratched.

If you clean the surface of the screen with a wet cloth, water

droplets on the surface may enter into the product, resulting in

malfunction.

Cleaning the cabinet

When cleaning the cabinet of this product, gently wipe it with a

clean soft cloth (e.g., cotton and flannel). If you use a dusty or hard

cloth or if you rub the cabinet hard, the surface of the cabinet will

be scratched.

The cabinet of this product is mostly composed of plastic. Do not

use chemicals such as benzene or thinner to clean the cabinet.

Using these chemicals may result in quality deterioration or coating

removal.

Do not expose the product to volatile gas or fluid such as pesticide.

Do not make the product contact with rubber or vinyl products for a

long period of time. The effect of plasticizer in the plastic may result

in quality deterioration or coating removal.

If you clean the surface of the cabinet with a wet cloth, water

droplets on the surface may enter into the product, resulting in

malfunction.

Handles at the rear of the plasma television

Do not remove the handles from the rear of the plasma television.

When moving the plasma television, ask another person for help

and use the handles attached to the rear of the plasma television.

Do not move the plasma television by holding only a single handle.

Do not use the handles to hang the product when installing or

carrying the product, for example. Do not use the handles for the

purpose of preventing the product from tilting over.

Fan motor noise

The rotation speed of the cooling fan motor increases when the

ambient temperature of the plasma television becomes high. You

may hear the sound of the fan motor at that time.

To use this product for a long period of time

The Energy Save function can maintain efficiency of the screen for

a long period of time. Setting the Energy Save function to “Mode 1”

is recommended in order to maintain the efficiency of the screen for

a long period of time.

Important user information01

8

En

Caution

Panel sticking and after-image lag

Displaying the same images such as still images for a long time

may cause after-image lagging. This may occur in the following two

cases.

After-image lagging due to remaining electrical load

When image patterns with very high peak luminance are displayed

for more than one minute, after-image lagging may occur due to the

remaining electric load. The after-images remaining on the screen

will disappear when moving images are displayed. The time for the

after-images to disappear depends on the luminance of the still

images and the time they had been displayed.

After-image (lag image) due to burning

Avoid displaying the same image on the plasma television

continuously over a long period of time.

If the same image is displayed continuously for a long period, or for

shorter periods of time over several days, a permanent after-image

may remain on the screen due to burning of the fluorescent

materials. Such images may become less noticeable if moving

images are later displayed, but they will not disappear completely.

Note

• When a still image, such as a programme menu, is displayed for

5 minutes to 10 minutes, the system automatically turns the

image off to prevent damage from screen burning.

• To prevent screen burning, the display position is automatically

changed imperceptibly when watching plasma television (see

Orbiter on page 55).

Preventing damage from screen burning

• We recommend that you enjoy watching images displayed in

full screen, except when doing so may result in copyright

infringement (see page 53).

• Set the Side Mask detection function to “On”, the High

Definition 16:9 aspect ratio images containing side masks will

be detected and the side masks will be added automatically or

the image displayed in full screen, leading to more effective

countermeasures taken for the screen burning (see Detecting

side masks on page 54).

Safety precautions 02

9

En

English

Chapter 2

Safety precautions

Electricity is used to perform many useful functions, but it can also

cause personal injuries and property damage if improperly handled.

This product has been engineered and manufactured with the

highest priority on safety. However, improper use can result in

electric shock and/or fire. In order to prevent potential danger,

please observe the following instructions when installing, operating

and cleaning the product. To ensure your safety and prolong the

service life of your product, please read the following precautions

carefully before using the product.

1. Read instructions - All operating instructions must be read and

understood before the product is operated.

2. Keep this manual in a safe place - These safety and operating

instructions must be kept in a safe place for future reference.

3. Observe warnings - All warnings on the product and in the

instructions must be observed closely.

4. Follow instructions - All operating instructions must be

followed.

5. Cleaning - Unplug the power cord from the AC outlet before

cleaning the product. To clean the product, use the supplied

cleaning cloth or other soft clothes (e.g., cotton, flannel). Do

not use liquid cleaners or aerosol cleaners.

6. Attachments - Do not use attachments not recommended by

the manufacturer. Use of inadequate attachments can result

in accidents.

7. Water and moisture - Do not use the product near water, such

as bathtub, washbasin, kitchen sink and laundry tub,

swimming pool and in a wet basement.

8. Stand - Do not place the product on an unstable cart, stand,

tripod or table. Placing the product on an unstable base can

cause the product to fall, resulting in serious personal injuries

as well as damage to the product. Use only a cart, stand, tripod,

bracket or table recommended by the manufacturer or sold

with the product. When mounting the product on a wall, be

sure to follow the manufacturer's instructions. Use only the

mounting hardware recommended by the manufacturer.

9. When relocating the product placed on a cart, it must be

moved with utmost care. Sudden stops, excessive force and

uneven floor surface can cause the product to fall from the

cart.

10. Ventilation - The vents and other openings in the cabinet are

designed for ventilation. Do not cover or block these vents and

openings since insufficient ventilation can cause overheating

and/or shorten the life of the product. Do not place the product

on a bed, sofa, rug or other similar surface, since they can

block ventilation openings. This product is not designed for

built-in installation; do not place the product in an enclosed

place such as a bookcase or rack, unless proper ventilation is

provided or the manufacturer's instructions are followed.

11. Power source - This product must operate on a power source

specified on the specification label. If you are not sure of the

type of power supply used in your home, consult your dealer or

local power company.

12. Power cord protection - The power cords must be routed

properly to prevent people from stepping on them or objects

from resting on them. Check the cords at the plugs and product.

13. The plasma television used in this product is made of glass.

Therefore, it can break when the product is dropped or applied

with impact. Be careful not to be injured by broken glass pieces

in case the plasma television breaks.

14. Overloading - Do not overload AC outlets or extension cords.

Overloading can cause fire or electric shock.

15. Entering of objects and liquids - Never insert an object into the

product through vents or openings. High voltage flows in the

product, and inserting an object can cause electric shock and/

or short internal parts. For the same reason, do not spill water

or liquid on the product.

16. Servicing - Do not attempt to service the product yourself.

Removing covers can expose you to high voltage and other

dangerous conditions. Request a qualified service person to

perform servicing.

17. Repair - If any of the following conditions occurs, unplug the

power cord from the AC outlet, and request a qualified service

person to perform repairs.

a. When the power cord or plug is damaged.

b. When a liquid was spilled on the product or when objects

have fallen into the product.

c. When the product has been exposed to rain or water.

d. When the product does not operate properly as described

in the operating instructions.

Do not touch the controls other than those described in the

operating instructions. Improper adjustment of controls not

described in the instructions can cause damage, which often

requires extensive adjustment work by a qualified technician.

e. When the product has been dropped or damaged.

f. When the product displays an abnormal condition. Any

noticeable abnormality in the product indicates that the

product needs servicing.

18. Replacement parts - In case the product needs replacement

parts, make sure that the service person uses replacement

parts specified by the manufacturer, or those with the same

characteristics and performance as the original parts. Use of

unauthorized parts can result in fire, electric shock and/or

other danger.

19. Safety checks - Upon completion of service or repair work,

request the service technician to perform safety checks to

ensure that the product is in proper operating condition.

20. Wall or ceiling mounting - When mounting the product on a

wall or ceiling, be sure to install the product according to the

method recommended by the manufacturer.

21. Heat sources - Keep the product away from heat sources such

as radiators, heaters, stoves and other heat-generating

products (including amplifiers).

22. Unplug the power cord from the AC outlet before installing the

speakers.

23. Never expose the screen of the plasma television to a strong

impact, for example, by hitting it. The screen may be broken,

resulting in fire or personal injury.

24. Do not expose the plasma television to direct sunlight for a

long period of time. The optical characteristics of the front

protection panel changes, resulting in discoloration or warp.

25. The plasma television weighs about 55.5 kg (122.4 lbs.) for the

PDP-LX608D/PDP-LX6080D and about 38.3 kg (84.4 lbs.) for the

PDP-LX508D/PDP-LX5080D. Because it has small depth and is

unstable, unpack, carry, and install the product with one more

person at least and use the handles.

Safety precautions02

10

En

Installation precautions

Observe the following precautions when installing with any items

such as the optional stand.

When using the optional stand, brackets, or equivalent

items

• Ask your dealer to perform the installation.

• Be sure to use the supplied bolts.

• For details, see the instruction manual that comes with the

optional stand (or equivalent items).

When using other items

• Consult your dealer.

• The following mounting holes can be used for the installation:

Rear view

(PDP-LX608D/PDP-LX6080D)

(PDP-LX508D/PDP-LX5080D)

Caution

• Be sure to use four or more mounting holes symmetrical to the

vertical and horizontal median lines.

• Use M8 screws, which go 12 mm to 18 mm in depth from the

mounting surface of the plasma television. See the side view

shown below.

• Be careful not to block the ventilation opening at the rear of the

plasma television.

• Be sure to install the plasma television on a flat surface

because it contains glass.

• The screw holes other than the illustrations on the left are to be

used only for the specified products. Never use them for

mounting non-specified products.

• Do not mount or remove the plasma television to or from the

stand, with speakers attached.

Note

• It is strongly recommended to use the optional Pioneer

mounting products.

• Pioneer shall not be liable for any personal injury or product

damage that results from the use of mounting items other than

the optional Pioneer products.

Side view

Median line

Mounting

holes

Median

line

Mounting

holes

Median

line

Median line

Mounting holes

Mounting surface

Plasma television

M8 screw

12 mm to 18 mm

Mounting bracket

(or equivalent)

Supplied accessories 03

11

En

English

Chapter 3

Supplied accessories

Check that all of the following accessories are supplied in the box.

Power cable

Only the power cable appropriate for your country or region is

supplied:

Remote control unit

AA size battery x 2

(for remote control unit)

Ferrite core

Cable tie (for ferrite core)

Speed clamp x 3

Bead band x 3

Cleaning cloth

Warranty card

Terminal position sheet

(for use when mounting the plasma television on the wall)

(PDP-LX608D/PDP-LX6080D only)

Operating instructions x 2

For Europe, except UK and Republic of Ireland

For UK and Republic of Ireland

Part names04

12

En

Chapter 4

Part names

Plasma television

(Front)

1  button (This button is located on the bottom of the side

panel of the plasma television for the PDP-LX608D/PDP-

LX6080D and at the bottom on the rear panel for the PDP-

LX508D/PDP-LX5080D. (See on page 13.) If the button is

off, the power will not turn on even when

, 0 to 9 on the

remote control unit or STANDBY/ON on the plasma television

is pressed. To turn on the power, press

. (You can aslo slide

 up for PDP-LX608D/PDP-LX6080D)).

2 POWER ON indicator

3 STANDBY indicator

4 TIMER indicator

• The TIMER indicator lights up when one or more DTV

programmes are preset for watching or recording (see pages

47 to 49).

5 Room Light Sensor

6 Remote control sensor

7 STANDBY/ON button

8INPUT button

9 VOLUME +/– buttons

10 CHANNEL +/– buttons

11 USB port

12 PHONES output terminal

13 INPUT 5 terminal (S-VIDEO)

14 INPUT 5 terminal (VIDEO)

15 INPUT 5 terminals (AUDIO)

Viewed from the underside of the display

Viewed from the front of the display

Side PDP-LX608D/PDP-LX6080D PDP-LX508D/PDP-LX5080D Side

7

9

10

8

12

11

14

13

15

ON STANDBY TIMERON STANDBY TIMER

5 6

4

3

2

11

5 6

4

3

2

1

The terminals on side panels are common to the PDP-LX608D/PDP-

LX6080D and PDP-LX508D/PDP-LX5080D.

1

Part names 04

13

En

English

Plasma television

(Rear)

1  button

2 AC IN terminal

3 RS-232C terminal (used for factory setup)

4 CONTROL OUT terminal (supports SR+)

5 INPUT 1 terminal (HDMI)

6 INPUT 3 terminal (HDMI)

7 INPUT 4 terminal (HDMI)

8 PC INPUT terminal (Analogue RGB)

9 COMMON INTERFACE slot

• For a CA Module with a smart card

10 ANT (Antenna) input terminal

• Power can be supplied through this terminal

11 INPUT 1 terminal (SCART)

12 INPUT 2 terminal (SCART)

13 INPUT 3 terminal (SCART)

14 INPUT 2 terminals (Audio)

15 INPUT 2 terminals (COMPONENT VIDEO: Y, P

B

, P

R

)

16 AUDIO OUT terminals

17 SUBWOOFER output terminal

18 PC INPUT terminal (Audio)

19 DIGITAL OUT terminal (OPTICAL)

20 SPEAKERS terminals (right/left)

17

PDP-LX608D/PDP-LX6080D PDP-LX508D/PDP-LX5080D

11

12

13 14 15 16

18

20

19

4 3 2

7 8

109

65

1

The terminals on the rear panel are common to the PDP-LX608D/PDP-LX6080D and

PDP-LX508D/PDP-LX5080D.

*For exact terminal positions, refer to the

terminal position sheet located near the

terminal compartment.

Part names04

14

En

Remote control unit

This section describes the functions of the buttons available when

the TV mode has been selected by using the SELECT button. For the

buttons controlling other equipment, see Controlling other

equipment using the supplied remote control unit starting from

page 69.

1 : Turns on the power to the plasma television or places it

into the standby mode.

2 INPUT: Selects an input source of the plasma television.

(“INPUT 1”, “INPUT 2”, “INPUT 3”, “INPUT 4”)

30 to 9: TV/External input mode: Selects a channel.

Teletext mode: Selects a page.

Turns the power on when the STANDBY indicator lights red.

4PC: Selects the PC terminal as an input source.

5 INPUT 5: Selects INPUT 5 as the input source of the plasma

television.

6 c: Switches the screen mode among 2-screen, picture-in-

picture, and single-screen.

7P+/P–: TV/External input mode: Selects a channel.

w/x: Teletext mode: Selects a page.

8 TV/DTV: Switches between the TV and DTV input modes.

9 SELECT: Switches the selection among TV, STB, DVD/DVR,

and VCR, so that you can control other connected equipment,

using the supplied remote control unit.

10 TV, STB, DVD/DVR, VCR: These indicators show the

current selection and status when you control other connected

equipment, using the supplied remote control unit.

11 RETURN: Restores the previous menu screen.

12 ///: Selects a desired item on the setting screen.

ENTER: Executes a command.

13 EXIT: Returns to the normal screen in one step.

14 Colour (RED/GREEN/YELLOW/BLUE):

Teletext mode: Selects a page.

15 [: Jumps to Teletext subtitle page.

Turns subtitle on and off in DTV input mode depending on the

broadcast.

16 k: Displays hidden characters.

17 HDMI CONTROL: Displays the HDMI Control menu.

18 g: Sets the sound multiplex mode.

19 p y INFO: Displays the channel information.

Displays the banner information in DTV input mode.

20 : Moves the location of the small screen when in the

picture-in-picture mode.

21 : Switches between the two screens when in the 2-screen

or picture-in-picture mode.

22 i +/i –: Sets the volume.

23 e: Mutes the sound.

24 HOME MENU: Displays the HOME MENU screen.

25 EPG: Displays the Electronic Programme Guide in DTV input

mode.

26 m: Selects the Teletext mode (all TV image, all TEXT image,

TV/TEXT image).

27 l: Displays an Index page for the CEEFAX/FLOF format.

Displays a TOP Over View page for the TOP format.

28 f: Selects the screen size.

29 d: TV/External input mode: Freezes a frame from a moving

image. Press again to cancel the function.

: Teletext mode: Stops updating Teletext pages. Press

again to release the hold mode.

Note

• When using the remote control unit, point it at the plasma

television.

1

1 2 3

4 5 6

7 8 9

PC

0

2 3 4

INPUT

INFO

INPUT 5

TV/DTV

SELECT

RETURN

MENU

EXIT EPG

HOME MENU

TV

DVD TOP MENU / GUIDE

DVD HDD

DISC

NAVI

HDMI

CONTROL

STB

DVD/

DVR

VCR

SOURCE

P

ENTER

1

2

3

4 19

22

20

25

26

21

24

27

28

29

23

5

7

9

13

15

18

14

12

11

16

17

10

8

6

Preparation 05

15

En

English

Chapter 5

Preparation

Installing the plasma television

Location

• Avoid direct sunlight. Maintain adequate ventilation.

Caution

• If you do not leave sufficient space above the plasma television,

it will not receive enough ventilation and will not operate

properly.

• Pioneer will not be responsible for accident or damage caused

by inadequate installation or stabilization, erroneous operation,

remodeling or natural disasters.

Note

• Allow enough space around the upper and back parts when

installing to ensure adequate ventilation of the rear of the unit.

• Be sure to install the plasma television in a flat, stable location.

Using the optional Pioneer stand

For details on installation, refer to the instruction manual supplied

with the stand.

Using the optional Pioneer speakers

For details on installation, refer to the instruction manual supplied

with the speakers.

Moving the plasma television

When installing on a rack, etc., hold the plasma television as shown

below. Because the plasma television is heavy, be sure to have

someone help you when moving it.

(for PDP-LX608D/PDP-LX6080D)

(for PDP-LX508D/PDP-LX5080D)

Note

• Do not use the speaker to support the weight of the plasma

television.

• Do not hold the plasma television by the speaker mounting

fittings.

Over 50 cm

Over

10 cm

Preparation05

16

En

Preventing the plasma television from

falling over

After installing the stand, be sure to take special care to ensure that

the plasma television will not fall over and is stabilized to both the

wall and rack.

Stabilizing on a table or rack

Stabilize the plasma television as shown in the diagram using the

plastic bands and screws supplied with the optional stand.

Note

• To stabilize the plasma television on a table or rack, also use

commercially available wood screws that have a nominal

diameter of 4 mm and that are at least 20 mm long.

Drill a hole in the middle at the rear of the tabletop panel before

using a wood screw. Perform this work the same way on the left and

right sides.

Drill a hole in the middle at the rear of the tabletop panel before

using a wood screw. Perform this work the same way on the left and

right sides.

Using a wall for stabilization

1 Attach falling prevention bolts (hooks) to the plasma

television.

2 Use strong cords to stabilize it appropriately and firmly to a

wall, pillar, or other sturdy element.

Perform this work in the same way on the left and right sides.

Use hooks, cords and fittings that are available on the market.

Recommended hook: Nominal diameter 8 mm, length 12 mm to

18 mm

Wood screw

(commercially available,

4 mm x 20 mm min.)

Screw

(M4 x 10 mm)

Screw

(M4 x 10 mm)

20 mm min.

4 mm

8 mm to 15 mm

(PDP-LX608D/PDP-LX6080D)

20 mm min.

4 mm

8 mm to 15 mm

Screw

(M4 x 10 mm)

Wood screw

(commercially available,

4 mm x 20 mm min.)

Wood screw

ScrewScrew

(PDP-LX508D/PDP-LX5080D)

M8

12 mm to 18 mm

1. Hook

2. Cord

Fitting

Preparation 05

17

En

English

Caution

• A table or rack with adequate strength should always be used to

support the plasma television. Failure to do so could result in

personal injury and physical damage.

• When installing the plasma television, please take the

necessary safety measures to prevent it from falling or

overturning in case of emergencies, such as earthquakes, or of

accidents.

• If you do not take these precautions, the plasma television could

fall down and cause injury.

• The screws, hooks, cords and other fittings that you use to

secure the plasma television to prevent it from overturning will

vary according to the composition and thickness of the surface

to which it will be attached.

• Select the appropriate screws, hooks, cords, and other fittings

after first inspecting the surface carefully to determine its

thickness and composition and after consulting a professional

installer if necessary.

Basic connections

Connecting the antenna

To enjoy a clearer picture, use an outdoor antenna. The following is

a brief explanation of the types of connections that are used for a

coaxial cable.

Caution

• When the “Aerial Power” setting is on, directly connect the

aerial to the ANT input terminal at the rear of the plasma

television. Connecting any device between the aerial and

plasma television may cause damage to the device.

• Connect a 75-ohm coaxial cable (commercially available) to the

ANT terminal.

• If “Aerial Power” setting is enabled, use an indoor antenna with

signal amplifier, 5 V 30 mA.

Antenna cable (commercially available)

If your outdoor antenna uses a 75-ohm coaxial cable with a

standard DIN45325 plug (IEC169-2), plug it into the antenna

terminal at the rear of the plasma television.

Note

• If the antenna is not connected correctly, the quality of

reception may be impaired. If images are not displaying

correctly, check whether the antenna connection is correct or

not.

Routing cables

When the speaker is installed under the plasma television panel

(PDP-LX508D/PDP-LX5080D):

Note

• Use the supplied bead bands as necessary.

• When tidying up your speaker cables, make sure to bundle them

so that they are not subjected to any pressure.

Standard DIN45325 plug (IEC169-2)

75-ohm coaxial cable (round cable)

(commercially available)

Rear view

Speaker cable

Bead band

Rear view

Preparation05

18

En

Attaching speed clamps to the main unit

Use the speed clamps as necessary to route the connecting cables.

The diagrams below show the location of the holes on the rear of the

plasma television.

(PDP-LX608D/PDP-LX6080D)

(PDP-LX508D/PDP-LX5080D)

Attaching and removing speed clamps

Insert [1] into an appropriate hole on the rear of the plasma

television and snap [2] into the back of [1] to lock the clamp.

• Speed clamps are designed to be difficult to undo once in place.

Please attach them carefully.

• Use pliers to twist the clamp 90º, pulling outward. The clamp

may deteriorate over time and become damaged if removed.

• Be careful not to subject any connecting cables to strain.

Note

• Use the speed clamps as necessary.

Attaching the ferrite core

Attach the accessory ferrite core to the end of the power cord as

shown in the accompanying illustration. Use the provided cable tie

to prevent the ferrite core from slipping on the table.

If you do not do this, the plasma television will not conform to

mandatory CE standards.

Connecting the power cord

Note

• Disconnect the power cord from the power outlet when the

plasma television is not going to be used for a long period of

time.

• Insert the power plug in the AC outlet, after all other

components are connected.

1

2

1

2

3

4

Ferrite core

Cable tie

AC power cord

To power outlet

As close as possible

Europe, except UK and

Republic of Ireland

UK and Republic of Ireland

Power cord

Rear view

Preparation 05

19

En

English

Preparing the remote control unit

Inserting batteries

1 Open the battery cover.

2 Load the supplied two AA size batteries while inserting

their respective negative polarity (–) ends first.

Place batteries with their terminals corresponding to the (+) and (–)

indicators in the battery compartment.

3 Close the battery cover.

Caution

Improper use of batteries can result in chemical leakage or an

explosion. Be sure to follow the instructions below.

• When you replace the batteries, use manganese or alkaline

ones.

• Place the batteries with their terminals corresponding to the (+)

and (–) indicators.

• Do not mix batteries of different types. Different types of

batteries have different characteristics.

• Do not mix old and new batteries. Mixing old and new batteries

can shorten the life of new batteries or cause chemical leakage

in old batteries.

• Remove batteries as soon as they have worn out. Chemicals

that leak from batteries can cause a rash. If you find any

chemical leakage, wipe thoroughly with a cloth.

• The batteries supplied with this product may have a shorter life

expectancy due to storage conditions.

• If you will not use the remote control unit for an extended period

of time, remove the batteries from it.

• WHEN DISPOSING OF USED BATTERIES, PLEASE COMPLY

WITH GOVERNMENTAL REGULATIONS OR

ENVIRONMENTAL PUBLIC INSTITUTION’S RULES THAT

APPLY IN YOUR COUNTRY/AREA.

Operating range of the remote control

unit

Operate the remote control unit while pointing it toward the remote

control sensor located at the bottom right of the front panel of the

plasma television. The distance from the remote control sensor

must be within 7 m and the angle relative to the sensor must be

within 30 degrees in the right, left, upward, or downward direction.

Note

• For remote control sensor locations, see Part names on page 12.

Caution

• Do not expose the remote control unit to shock. In addition, do

not expose the remote control unit to liquids, and do not place

in an area with high humidity.

• Do not install or place the remote control unit under direct

sunlight. The heat may cause deformation of the unit.

• The remote control unit may not work properly if the remote

control sensor of the plasma television is under direct sunlight

or strong lighting. In such case, change the angle of the lighting

or plasma television, or operate the remote control unit closer to

the remote control sensor.

• When any obstacle exists between the remote control unit and the

remote control sensor, the remote control unit may not function.

• As the batteries become empty, the remote control unit can

function within a shorter distance from the remote control

sensor. Replace the batteries with new ones early enough.

• The plasma television emits very weak infrared rays from its

screen. If you place such equipment operated through infrared

remote control as a VCR nearby, that equipment may not

receive commands from its remote control unit properly or

entirely. If this is the case, place that equipment at a location far

enough from the plasma television.

• Depending on the installation environment, infrared rays from

the plasma television may not allow this system to properly

receive commands from the remote control unit or may shorten

allowable distances between the remote control unit and the

remote control sensor. The strength of infrared rays emitted

from the screen differs, depending on images displayed on the

screen.

30º

Remote

control

sensor

7 m

Watching TV06

20

En

Chapter 6

Watching TV

Important

• Before watching broadcast channels, the built-in TV tuner must

be set up. See Setting up TV channels on page 27 for how to do

this.

Turning the power on

•Turn

a

on on the plasma television when the POWER ON and

STANDBY indicators are off (see

Part names

on pages 12 and

13).

• The system is on.

• The POWER ON indicator lights up blue.

• Press

a

or 0 to 9 on the remote control unit or STANDBY/ON

on the plasma television if the STANDBY indicator lights red.

• The POWER ON indicator lights up blue.

•If you press 0 on the remote control unit, images from INPUT 1

will be displayed.

• If you press 1 to 9, TV images will be displayed.

Placing the system into standby

Press

a

on the remote control unit or STANDBY/ON on the

plasma television.

• The STANDBY indicator lights up red.

• The system enters the standby mode and the image on the

screen disappears.

Note

•When

a

on the plasma television is off, you cannot turn the

power on by pressing

a

or

0

to

9

on the remote control unit or

STANDBY/ON

on the plasma television.

• It is recommended not to unplug the plasma television from a

power outlet when it is not in use. When in the standby mode, the

plasma television automatically receives Electronic Programme

Guide and DTV Auto Update signals.

• When the system is placed into standby mode, the main power

flow is cut and the system is no longer fully operational. A minute

flow of power feeds the system to maintain operational readiness.

• If you are not going to use the plasma television for a long period

of time, be sure to remove the power cord from the power outlet.

• If you unplug the plasma television from a power outlet, the clock

inside the plasma television will reset with certain functions,

such as timer recording, are disabled. After plugging in the

plasma television again, clock information is automatically

obtained as you tune in a DTV programme.

If you unplug the plasma television from a power outlet when a

timer recording programme(s) has been registered, the plasma

television may automatically tune in to the DTV programme in

order to obtain clock information when you turn the power on the

next time.

It may take a short while until the clock information is obtained.

An alert will appear when you try to tune in an analogue

programme before obtaining the clock information.

Plasma television status indicators

The table below shows the operational status of the plasma

television. You can check the current status of the system with the

indicators on the plasma television.

For other than the above, see Troubleshooting on page 82.

Note

• You can select “Auto”, “High”, “Mid” or “Low” for the brightness

of the POWER ON indicator. When “Auto” is selected, the

brightness of the indicator changes to “High”, “Mid” or “Low” to

match the brightness level of the viewing area. For details, see

Blue LED Dimmer on page 55.

1

1 2 3

4 5 6

7 8 9

PC

0

2 3 4

INPUT

INFO

INPUT 5

TV/DTV

P

Indicator status System status

POWER ON STANDBY

The power cord of the plasma

television has been disconnected. Or,

the power cord of the plasma television

has been connected but the

a

button

of the plasma television is off.

Power to the system is on.

The system is in the standby mode.

La page est en cours de chargement...

Pioneer LX508D Le manuel du propriétaire

Pioneer LX508D Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents