Infinity 1.2s Manuel utilisateur
- Catégorie
- Subwoofers
- Taper
- Manuel utilisateur
Ce manuel convient également à
Owner’s Guide
INTERMEZZO
™
1.2s
ii
INTERMEZZO 1.2s
THIS INFINITY PRODUCT IS DESIGNED FOR 120-VOLT USE ONLY! FOR
DETAILED SAFETY PRECAUTIONS, PLEASE SEE FOLLOWING PAGE IN THIS
OWNER’S MANUAL FOR “IMPORTANT SAFETY INSTRUCTIONS.”
The lightning flash with arrowhead symbol, within an equilateral triangle, is
intended to alert the user to the presence of uninsulated “dangerous voltage” within
the product’s enclosure that may be of sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (servicing) instructions in
the literature accompanying the product.
L’éclair avec le symbole de la flèche, placé dans les limites d’un triangel équilatéral est
prévu pour avertir l’utilisateur de la présence de “tension dangereuse” non isolée dans
l’enceinte du produit qui pourrait être d’une importance suffisante pour présenter un
risque d’électrocution aux personnes.
Le point d’exclamation dans un triangel équilateral est prévu pour avertir l’utilisateur
de la présence d’instructions importantes pour les opérations et l’entretien (service)
dans les manuels fournis avec l’appareil.
ATTENTION: POUR EVITER LES CHOCS ELECTRIQUES, INTRODUIRE
LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE
CORRESPONDANTE DE LA PRISE ET POUSSER JUSQUAU FOND.
Este destello luminoso con un símbolo de punta de flecha dentro de un triángulo
equilátero tiene el objectivo de alertar al usuario sobre la presencia de “voltaje
peligroso” no aislado dentro de la caja del producto que puede ser de magnitud lo
suficientemente grande para constituir un riesgo de choque eléctrico para las personas.
Este punto de exclamación dentro de un triángulo equilátero tiene el objectivo de
alertar al usuario sobre la existencia de instrucciones operativas y de mantenimiento
(servicio) importantes en la literatura que acomaña el aparato.
CUIDADO: PARA REDUCIR EL RIESGO DE CHOQUE ELÉCTRICO, NO
RETIRE LA CUBIERTA (O RESPALDO). DENTRO NO HAY PEIZAS A LAS
QUE EL USUARIO PUEDE DAR SERVICIO. REMITA EL SERVICIO AL
PERSONAL DE SERVICIO CALIFICADO.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: SHOCK HAZARD, DO NOT OPEN.
AVIS: RISQUE DE CHOC ELECTRIQUE – NE PAS OUVRIR.
CUIDADO: PELIGRO DE CHOQUE ELÉCTRICO – NO ABRIR.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (0R BACK)
NO USER SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED PERSONNEL
Read First!
1.Read Instructions.All the safety and operating
instructions should be read before the product is
operated.
2.Retain Instructions.The safety and operating
instructions should be retained for future reference.
3.Heed Warnings. All warnings on the product and in
the operating instructions should be adhered to.
4.Follow Instructions. All operating and use
instructions should be followed.
5.Cleaning. Unplug this product from the wall outlet
before cleaning.Do not use liquid cleaners or aerosol
cleaners.Use a damp cloth for cleaning.
6.Attachments. Do not use attachments not
recommended by the product manufacturer,
as they may cause hazards.
7.Water and Moisture.To reduce the risk of fire or
electric shock,do not use this product outdoors or
near water–for example,near a bathtub,wash bowl,
kitchen sink or laundry tub;in a wet basement;near a
swimming pool;or the like.
8.Accessories. Do not place this product on an
unstable cart,stand,tripod,bracket or table.The
product may fall,causing serious injury to a child or
adult,and serious damage to the product.Use only
with a cart,stand,tripod,bracket or table
recommended by the manufacturer,or sold with the
product.Any mounting of the product should follow the
manufacturer’s instructions,and should use a
mounting accessory recommended by the
manufacturer.
9.A Product and Cart Combination
Should Be Moved with Care. Quick
stops,excessive force and uneven
surfaces may cause the product and
cart combination to overturn.
10.Ventilation. Slots and openings in the cabinet are
provided for ventilation and to ensure reliable
operation of the product and to protect it from
overheating,and these openings must not be blocked
or covered.The openings should never be blocked by
placing the product on a bed,sofa,rug or other
similar surface.This product should not be placed in a
built-in installation,such as a bookcase or rack,
unless proper ventilation is provided or the
manufacturer’s instructions have been adhered to.
11.Power Sources.This product should be operated
only from the type of power source indicated on the
marking label.If you are not sure of the type of power
supply to your home,consult your product dealer or
local power company.For products intended to operate
from battery power,or other sources,refer to the
operating instructions.
12.Grounding or Polarization.This product may be
equipped with a polarized alternating-current-line plug
(a plug having one blade wider than the other).This
plug will fit into the power outlet only one way.This is
a safety feature.If you are unable to insert the plug
fully into the outlet,try reversing the plug.If the plug
should still fail to fit,contact your electrician to
replace your obsolete outlet.Do not defeat the safety
purpose of the polarized plug.
13.Power-Cord Protection. Power-supply cords should
be routed so that they are not likely to be walked on or
pinched by items placed upon or against them,paying
particular attention to cords at plugs,convenience
receptacles,and the point where they exit from the
product.
14.Nonuse Periods.The power cord of the product
should be unplugged from the outlet when left unused
for long periods of time.
15.Outdoor Antenna Grounding. If an outside antenna
or cable system is connected to the product,be sure
the antenna or cable system is grounded so as to
provide some protection against voltage surges and
built-up static charges.Article 810 of the National
Electrical Code,ANSI/NFPA 70,provides information
with regard to proper grounding of the mast and
supporting structure,grounding of the lead-in wire to
an antenna discharge unit,size of grounding
conductors,location of antenna-discharge unit,
connection to grounding electrodes,and requirements
for the grounding electrode.See Figure A.
16.Lightning. For added protection for this product
during a lightning storm,or when it is left unattended
and unused for long periods of time,unplug it from
the wall outlet and disconnect the antenna or cable
system.This will prevent damage to the product due to
lightning and power-line surges.
17.Power Lines.An outside antenna system should not
be located in the vicinity of overhead power lines or
other electric light or power circuits,or where it can
fall into such power lines or circuits.When installing
an outside antenna system,extreme care should be
taken to keep from touching such power lines or
circuits,as contact with them might be fatal.
18.Overloading. Do not overload wall outlets,extension
cords,or integral convenience receptacles,as this can
result in a risk of fire or electric shock.
19.Object and Liquid Entry. Never push objects of any
kind into this product through openings,as they may
touch dangerous voltage points or short-out parts that
could result in a fire or electric shock.Never spill
liquid of any kind on the product.
20.Servicing. Do not attempt to service this product
yourself,as opening or removing covers may expose
you to dangerous voltage or other hazards.Refer all
servicing to qualified service personnel.
21.Damage Requiring Service. Unplug this product
from the wall outlet and refer servicing to qualified
service personnel under the following conditions:
a. The power-supply cord or the plug has been
damaged;or
b. Objects have fallen onto,or liquid has been spilled
into,the product;or
c. The product has been exposed to rain or water;or
d. The product does not operate normally when
following the operating instructions.Adjust only those
controls that are covered by the operating instructions,
as an improper adjustment of other controls may
result in damage and will often require extensive work
by a qualified technician to restore the product to its
normal operation;or
e. The product has been dropped or damaged in any
way;or
f. The product exhibits a distinct change in
performance;this indicates a need for service.
22.Replacement Parts. When replacement parts are
required,be sure the service technician has used
replacement parts specified by the manufacturer or
that have the same characteristics as the original
part.Unauthorized substitutions may result in fire,
electric shock or other hazards.
23.Safety Check. Upon completion of any service or
repairs to this product,ask the service technician to
perform safety checks to determine that the product is
in proper operating condition.
24.Wall or Ceiling Mounting.The product should be
mounted to a wall or ceiling only as recommended by
the manufacturer.
25.Heat.The product should be situated away from
heat sources such as radiators,heat registers,stoves
or other products (including amplifiers) that produce
heat.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with arrowhead
symbol within an equilateral triangle is
intended to alert the user to the presence
of uninsulated “dangerous voltage” within
the product’s enclosure that may be of
sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an
equilateral triangle is intended to alert the
user to the presence of important
operating and maintenance (servicing)
instructions in the literature accompanying
the appliance.
Antenna Lead-In Wire
Ground Clamp
Antenna Discharge Unit (NEC Section 810-20)
Grounding Conductors (NEC Section 810-21)
Electric Service Equipment
Ground Clamps
Power Service Grounding Electrode System
(NEC Art. 250, Part H)
Figure A.
Example of Antenna Grounding as per
National ElectricalCode ANSI/NFPA 70
IMPORTANT SAFETY PRECAUTIONS
iii
INTERMEZZO 1.2s
ii Caution
iii Important Safety Precautions
1 Technology
1 Ceramic Metal Matrix Diaphragms
™
(C.M.M.D.)
1 Room-Friendly Acoustical Design
2 Unpacking the Product/Included Accessories
3 Placement
4 Controls and Connections
5 Connection Methods 1–4
8 Operation
9 Room Adaptive Bass Optimization System
™
(R.A.B.O.S.)
10 Contents of the R.A.B.O.S.Test CD
10 R.A.B.O.S.Sound-Level Meter (RSLM)
15 What You Measure,What To Do
18 Adjusting the R.A.B.O.S.Equalizer
19 Final System Balance
20 Maintenance and Service
21 Specifications
22 R.A.B.O.S. Measurement Templates
Table of Contents
INTERMEZZO 1.2S OWNER’S GUIDE
iv
INTERMEZZO 1.2s
1
INTERMEZZO 1.2s
Intermezzo Series loudspeakers incorporate several innovative
technologies that,when implemented by exceptional engineering
talent after hours upon hours of subjective listening evaluations,
result in a loudspeaker that realistically and accurately reproduces
the signal source with minimal distortion and coloration.
CeramicMetalMatrixDiaphragms
™
(C.M.M.D.)
For decades,loudspeaker engineers have known that the ideal
transducer should be stiff,yet light,and have high internal
damping (damping is a material’s ability to absorb energy).
Infinity’s C.M.M.D.transducer is a significant advance in
transducer technology.Ceramic,a class of material new to
loudspeakers,offers better performance than that of other
materials.Ceramic is stiffer than metals and lighter than plastics
and typical composite materials;it also offers improved damping.
These ceramic-based transducers take us a giant step closer to
the ever-elusive “ideal transducer.”
In tweeters,C.M.M.D.technology offers stiffness and damping
superior to that of traditional metals and soft-dome materials.
In woofer and midrange applications,it offers accurate pistonic
operation over the entire frequency range of the driver,
completely eliminating coloration due to cone breakup and
dramatically reducing distortion.And when ceramic-metal-matrix
transducers are exposed to moisture,sunlight or extreme
temperatures,their performance does not deteriorate.
In addition to ceramic diaphragms,all the transducers incorporate
magnetic shielding and rigid cast-frames that,through our FEA
computer modeling and scanning-laser-vibrometer measurements,
have been optimized to reduce resonances.This ensures minimal
distortion and incomparable performance.
Amplifier
BASH
®
is an amplifier-power-supply technology that increases
efficiency by reducing power dissipation in the output section.
The BASH topology uses a high-efficiency,fast-response,switch-
mode power supply that provides the main voltage rails for a
linear Class-AB amplifier.By varying the output of the power
supply with the audio signal being amplified,a constant voltage
drop across the output transistors of the linear amplifier can be
maintained.This means that the power dissipation in the output
transistors is greatly reduced.
The result is an extremely efficient audio amplifier that does not
compromise audio performance.
Room-Friendly Acoustical Design
Driver quality is not the only requirement for exceptional
performance.Infinity’s engineers understand that the room in
which the loudspeaker is placed can greatly affect its
performance.To ensure that Intermezzo Series loudspeakers will
sound exceptional in even the most unexceptional listening
environment,Infinity has developed the proprietary Room Adaptive
Bass Optimization System™ (R.A.B.O.S.™).With a single band of
parametric equalization,the Intermezzo 1.2s can be adjusted to
tame any problematic room bass resonances below 80Hz.
We hope you enjoyed this brief introduction to the technology
of Intermezzo loudspeakers.If you would like to further explore
their technology and design,please ask your Infinity dealer
for the C.M.M.D.and R.A.B.O.S.White Papers.The White
Papers can also be downloaded from Infinity’s Web site at
www.infinitysystems.com.
TECHNOLOGY
Power
-1
-2
-3
-4
-5
-6
-7
-8
-9
-10
-11
-13
-15
-18
U-R
Batt
Unpacking the Product
Finish unpacking the speakers and check the contents.If you
suspect damage from transit,report it immediately to your dealer
and/or delivery service.Keep the shipping carton and packing
materials for future use.
Included Accessories ...
Grille Decorative
Side Panel
AC Cord
R.A.B.O.S.Kit (1)
Sound-Level Meter R.A.B.O.S.Test CD
Graph Templates Bandwidth Selector
Adjustment Key
2
INTERMEZZO 1.2s
3
INTERMEZZO 1.2s
Since the installation of a subwoofer can be somewhat more
complicated than installing full-range speakers,it is essential
that you read this section very carefully prior to connecting the
subwoofer to your system.Should you have questions relating to
your installation,it is advisable to call either your dealer or
Infinity’s Customer Service Department for advice.
The performance of the subwoofer is directly related to its
placement in the listening room and how you align the subwoofer
with its satellite speakers.Setting the volume of the subwoofer in
relationship to the left and right speakers is also of critical
importance because it is essential that the subwoofer integrates
smoothly with the entire system.Setting the subwoofer’s volume
level too high will result in an overpowering,boomy bass.Setting
the volume level too low will negate the effect of the subwoofer.
Generally speaking,the closer the subwoofer is placed to a room
boundary (walls and corners),the more bass output there will be.
If you are hearing too much low-frequency sound in relation to
the rest of the program material,move the subwoofer further
from the corner or wall.Conversely,if,after making all adjust-
ments,there is still not enough low-frequency energy,move the
subwoofer closer to a wall or corner.
Here are several additional facts on installation that may prove
useful.It is generally believed by most audio authorities that low
frequencies (below 125Hz) are nondirectional and,therefore,
placement of a subwoofer within any listening room is not
critical.While in theory it is true that the larger wavelengths,of
extremely low frequencies,are basically nondirectional,the fact
is that when installing a subwoofer within the limited confines of
a room,reflections,standing waves and absorptions generated
within the room will strongly influence the performance of any
subwoofer system.As a result,specific location of the subwoofer
becomes important,and we strongly recommend that you
experiment with placement before choosing a final location.
Placement will depend upon your room and the amount and
quality of bass required (for example,whether or not your room
permits placement of the subwoofer near either satellite).
PLACEMENT
➢
➢
SOFA
FRONT
LEFT
LEFT
SURROUND
FRONT
RIGHT
RIGHT
SURROUND
TV
CENTER
SUB
➢
➢
SOFA
LEFT
CHANNEL
RIGHT
CHANNEL
SUB
FIGURE 1
FIGURE 2
1
AC-Cord Input
2
Power Switch
3
Speaker-Level Inputs
4
Speaker-Level Outputs
5
High-Level High-Pass Filter Switch
6
Low-Level-Input Connectors
7
Low-Level-Output Connectors
8
Phase Switch
9
Low-Pass Filter Switch
J
Variable Low-Pass Filter Adjustment
K
Subwoofer-Level Control
R.A.B.O.S.Controls
L
Center-Frequency Adjustment
M
R.A.B.O.S.Level
N
Bandwidth Adjustment
120V – 60HZ 6A
–
++
–
–
++
–
INPUTS OUTPUTS
POWER
1
2
3
4
567
89
J
0
LOW-PASS
FILTER
LOW-PASS
FILTER
LOW-
LEVEL
INPUT
LOW-
LEVEL
OUTPUT
HIGH-LEVEL
HIGH-PASS
FILTER
PHASE
AC FUSE
6A 250V
180
80
50 130
ON
OFF
ON
OFF
INTERMEZZO 1.2s
L
R
L
R
L
R
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
¢
›
F
L
W
K
L
M
N
CONTROLS AND CONNECTIONS
Rear Panel
Front Panel
4
INTERMEZZO 1.2s
The Infinity Intermezzo 1.2s offers unprecedented flexibility for
connecting the system to any type of audio or home-theater system.
Consult the table at right to determine which system description
most closely matches your own,then follow the hook-up method
corresponding to that system.
If none of these system configurations seem to match yours,
consult your dealer or Infinity customer service for direction on
how best to hook up your system.
For Methods 2,3a,3b and 4,make sure all bass-management
features are properly set.The Audio channels should all be set to
“Small”or “High-Pass” and the subwoofer set to “On.”
–
++
–
+
–
OUTPUTS
POWER
0
LOW-PASS
FILTER
LOW-PASS
FILTER
LOW-
LEVEL
INPUT
LOW-
LEVEL
OUTPUT
HIGH-LEVEL
HIGH-PASS
FILTER
PHASE
AC FUSE
6A 250V
180
80
50 130
ON
OFF
ON
OFF
INTERMEZZO 1.2s
L
R
L
R
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
LOOSEN TERMINALS
INSERT BARE END;
TIGHTEN TERMINALS
SET LOW-PASS
FILTER
9
TO “ON”
SET HIGH-PASS SWITCH
5
TO “ON” OR “OFF” (SEE P. 8)
1.
2.
3.
4.
BLACK =
–
NO STRIPE =
–
STRIPE =
+
RED =
+
INPUTS
L
R
120V – 60HZ 6A
–
+
AMPLIFIER/RECEIVER
SPEAKER
OUTPUTS
LEFT RIGHT
(ONE CHANNEL SHOWN)
––
++
RIGHT
SPEAKER
–
+
2-Channel receiver or integrated amplifier
that has no subwoofer output or
Pre-out/Main-In connectors 1
2-Channel receiver or integrated amplifier
with preamp output and input connectors 2
2-Channel system with separate preamplifier
and power amplifier 2
Dolby* Pro Logic* with THX,
®
Dolby Digital,
or DTS
®
receiver with a filtered subwoofer
(or LFE) output connector 3a
Dolby Digital or DTS processor with separate
power amplifiers or multichannel amplifier 3b
Non-THX certified Dolby Pro Logic receiver
with full-range subwoofer outputs 4
System Type Connection Methods
Method 1
5
INTERMEZZO 1.2s
–
++
–
–
++
–
INPUTS OUTPUTS
POWER
0
LOW-PASS
FILTER
LOW-PASS
FILTER
LOW-
LEVEL
INPUT
LOW-
LEVEL
OUTPUT
HIGH-LEVEL
HIGH-PASS
FILTER
PHASE
AC FUSE
6A 250V
180
80
50 130
ON
OFF
ON
OFF
INTERMEZZO 1.2s
L
R
L
R
L
R
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
120V – 60HZ 6A
SURROUND RECEIVER
SUBWOOFER (LFE)
OUTPUT
(ONE CHANNEL SHOWN)
–
+
FRONT SPEAKER
OUTPUTS
TO MAIN SPEAKERS
SET LOW-PASS
FILTER
9
TO “OFF”
Method 3a
6
INTERMEZZO 1.2s
–
++
–
–
++
–
INPUTS OUTPUTS
POWER
0
LOW-PASS
FILTER
LOW-PASS
FILTER
LOW-
LEVEL
INPUT
LOW-
LEVEL
OUTPUT
HIGH-LEVEL
HIGH-PASS
FILTER
PHASE
AC FUSE
6A 250V
180
80
50 130
ON
OFF
ON
OFF
INTERMEZZO 1.2s
L
R
L
R
L
R
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
120V – 60HZ 6A
PREAMP OUTPUTS
L
R
(ONE CHANNEL SHOWN)
L
R
AMPLIFIER INPUTS
SET LOW-PASS
FILTER
9
TO “ON”
Method 2
7
INTERMEZZO 1.2s
–
++
–
–
++
–
INPUTS OUTPUTS
POWER
0
LOW-PASS
FILTER
LOW-PASS
FILTER
LOW-
LEVEL
INPUT
LOW-
LEVEL
OUTPUT
HIGH-LEVEL
HIGH-PASS
FILTER
PHASE
AC FUSE
6A 250V
180
80
50 130
ON
OFF
ON
OFF
INTERMEZZO 1.2s
L
R
L
R
L
R
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
120V – 60HZ 6A
RECEIVER
SUBWOOFER
OUTPUTS
L
R
SPEAKER
OUTPUTS
RIGHT
(ONE CHANNEL SHOWN)
– +
TO MAIN SPEAKERS
SET LOW-PASS
FILTER
9
TO “ON”
Method 4
–
++
–
–
++
–
INPUTS OUTPUTS
POWER
0
LOW-PASS
FILTER
LOW-PASS
FILTER
LOW-
LEVEL
INPUT
LOW-
LEVEL
OUTPUT
HIGH-LEVEL
HIGH-PASS
FILTER
PHASE
AC FUSE
6A 250V
180
80
50 130
ON
OFF
ON
OFF
INTERMEZZO 1.2s
L
R
L
R
L
R
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
120V – 60HZ 6A
AMPLIFIER PROCESSOR
SUBWOOFER (LFE)
OUTPUT
SPEAKER
OUTPUT
INPUT
– +
L
R
FRONT CHANNEL
OUTPUT
L
R
(ONE CHANNEL SHOWN)
TO MAIN
SPEAKERS
SET LOW-PASS
FILTER
9
TO “OFF”
Method 3b
8
INTERMEZZO 1.2s
Power On
Plug your subwoofer’sAC cord into a wall outlet.Do not use the
outlets on the back of the receiver.
Initially set the subwoofer’s Level Control K to the “O”position.
Turn on your sub by pressing the power button
2
on the rear
panel.
Turn on your entire audio system and start a CD or movie sound-
track at a moderate level.
Adjust Gain
Turn your subwoofer’s Level Control
K
up to the “5”position
(half way).If no sound emanates from the subwoofer,check the
AC-line cord and input cables.Are the connectors on the cables
making proper contact? Is the AC plug connected to a “live”
receptacle? Has the power button
2
been pressed to the “On”
position? (Note:The Level Control on the front panel will turn
green when the power is on.) Once you have confirmed that the
subwoofer is active,proceed by playing a CD,record or cassette.
Use a selection that has ample bass information.
Set the overall volume control of the preamplifier or stereo to a
comfortable level.Adjust the subwoofer’s Level Control
K
until
you obtain a pleasing blend of bass.Bass response should not
overpower the room but rather be adjusted so there is a
harmonious blend across the entire musical range.Many users
have a tendency to set the subwoofer volume too loud,
adhering to the belief that a subwoofer is there to produce lots
of bass.This is not entirely true.A subwoofer is there to enhance
bass,extending the response of the entire system so the bass
can be felt as well as heard.However,overall balance must
be maintained or the music will not sound natural.An
experienced listener will set the volume of the subwoofer so
its impact on bass response is always there but never obtrusive.
OPERATION
Crossover Adjustments
If you are using Method 1 as your connection method,you need to
set the High-Level High-Pass Filter 5 to “On” or “Off.” When on,
this adjustment limits the low frequencies that your main speakers
will reproduce.If you would like your main speakers to also
reproduce frequencies below 80Hz,you may set this switch to
“Off.”If you are using speakers that do not reproduce low
frequencies well,we recommend that you set the switch to “On.”
Low-Pass Filter Adjustment Control J – The Low-Pass Control
determines the highest frequency at which the subwoofer
reproduces sounds.If your main speakers can comfortably
reproduce some low-frequency sounds,set this control to a
lower frequency setting,between 50Hz – 100Hz.This will
concentrate the subwoofer’s efforts on the ultradeep bass
sounds required by today’s films and music.If you are using
smaller bookshelf speakers that do not extend to the lower bass
frequencies,set the Low-Pass Filter Adjustment Control to a
higher setting,between 120Hz – 150Hz.
Note: This control will have no effect if the Low-Pass Filter
Switch 9 is set to “Off.”If you have a Dolby Digital or DTS
processor/receiver,the Low-Pass Frequency is set by the
processor/receiver.So you should leave the Low-Pass Filter
Switch 9 in the “Off”position.Consult your owner’s manual to
learn how to view or change this setting.
Phase Control
The Phase Switch 8 determines whether the subwoofer
speaker’s piston-like action moves in and out with the main
speakers,0˚,or opposite the main speakers,180˚.Proper phase
adjustment depends on several variables such as room size,
subwoofer placement and listener position.Adjust the phase
switch to maximize bass output at the listening position.
Final Positioning
After correctly connecting the Intermezzo 1.2s and verifying that
both the subwoofer and main speakers are playing,it is time to
optimize the system for your particular listening room.Earlier,
you placed the subwoofer in its general location.Finding the
exact location for optimum performance sometimes only involves
moving the speakers up to a few inches in any direction.We urge
you,therefore,to experiment with placement until your speakers
deliver their full potential.
9
INTERMEZZO 1.2s
Infinity R.A.B.O.S.is a simple-to-use,yet sophisticated,low-
frequency calibration system.It is designed to work in
conjunction with Infinity Intermezzo self-amplified subwoofers.
The Intermezzo 1.2s subwoofer contains a parametric equalizer
that you will adjust as indicated by the R.A.B.O.S.test results.
Following these instructions,you will optimize the Intermezzo
subwoofers’response characteristics to complement their
environment.This will dramatically improve the sound of your
system.The optimization process takes less than 30 minutes.
The R.A.B.O.S.Kit Includes
the Following Components:
• Specialized Sound-Level Meter
• Test CD
• Instructions
• Measurement Templates
• Width Selector
• Adjustment “Key”
What R.A.B.O.S.Does
The Test CD provides specially designed signals you will use
while performing measurements.The sound-level meter provided
is used to “acquire”the information needed for adjustments.You
will create a response plot on the Measurement Template.Using
the Width Selector,you will then determine the appropriate
equalizer settings.The “Key”is used to adjust the parametric
equalizer built into the Intermezzo subwoofer.After adjustment,
the test sequence is repeated to confirm your settings.
The R.A.B.O.S.Goal
It is a fact of audio that what we hear at low frequencies is
determined as much or more by the listening room than by the
loudspeaker itself.Placement of the loudspeakers and listeners
and the acoustical characteristics of the room surfaces are all
important determinants of bass quantity and quality.In most
practical situations,there is little that can be done about this,
except for patient trial-and-error repositioning of the
loudspeakers and listeners.Usually,the practical constraints of a
living space and the impracticality of massive acoustical
treatment mean that equalization is the only practical solution.
Professional sound engineers routinely employ sophisticated
measurement systems and equalizers to optimize speakers to the
installation.This has never been practical for the home
audiophile.This is why R.A.B.O.S.was created.R.A.B.O.S.enables
you to identify the dominant low-frequency response
characteristic of your room.Once you know the problem,
R.A.B.O.S.provides the tools needed to optimize the low-
frequency characteristics of the speakers to the room they are
in,exactly as the professional sound engineers do it.
Performing R.A.B.O.S.Tests
These instructions assume you have already installed your
Intermezzo subwoofer according to the information provided in
the Owner’s Guide.It is also assumed that all equipment in your
entertainment system is interconnected properly and is in good
operating condition.
Preparations
Before beginning R.A.B.O.S.tests,please check the following:
• Make sure all three R.A.B.O.S.controls on the Intermezzo 1.2s
are turned fully clockwise.
• Make sure the loudness contour (if any) on your receiver/
processor/preamp is turned off.
• Set the tone controls (Bass and Treble) to their center or
flat positions.
• Bypass all surround and effects features of your receiver/
processor/preamp or set to Stereo Bypass.
• If you are using a multichannel surround processor or
receiver,make sure all bass-management features are properly
set.The Audio channels should all be set to “Small”or “High-
Pass”and the subwoofer set to “On.”
You must have a CD player in the system.A CD player remote
control is quite convenient but not essential.
For best results,it is recommended that all major furnishings are
in place and that all doors and windows in the listening area are
in their normal positions.That is,if you normally listen to music
with all doors closed,then this is how they should be during this
procedure.
Try to minimize ambient noise while running tests.Turn off all
major appliances and any air conditioning or furnace fans.These
can create significant subsonic noise that may be barely
perceptible but which can wreak havoc on low-frequency
measurements.
Critical information is highlighted with this mark:
Helpful hints are marked with this symbol:
ROOM ADAPTIVE BASS OPTIMIZATION SYSTEM
10
INTERMEZZO 1.2s
Power is switched on or off by pressing the button directly below
the bar-graph window.When the unit is on,one or more LEDs will
always be illuminated.The function of the LEDs is described in the
following section.
• Power-On/Low Signal: This is indicated by the illumination of
any LED on the bar graph.If the sound level in the room is below
the measurement range of the instrument,a green LED near the
bottom of the bar graph will be illuminated.
• Normal Measurements:When the sound level is within the
range of the RSLM,the green LED will be off and one of the red
LEDs in the bar graph will be illuminated,indicating the relative
sound level,in decibels (dB).
• Over-Range:If the sound level exceeds the range of the meter,
0dB through -5 will all light simultaneously.
• Low Battery:When the battery voltage is too low for accurate
measurements,an LED at the bottom of the bar graph will be
illuminated.Replace the battery.
Do not attempt measurements when this light is on.
RSLM Placement
Determine where in the room you are most likely to sit when
listening to music or watching a movie.This is where you will
want to hold the RSLM during measurements.The RSLM should
be oriented so it can be easily read and held at your seated ear
level during tests.
You must use this same position for all tests.
The RSLM can be mounted on a standard camera tripod.
This will ensure the best results.
Tracks 53–62 of the R.A.B.O.S.Test CD are test tones that can be
used for general diagnostics of your system.They are not used
for R.A.B.O.S.settings.
THE R.A.B.O.S.SOUND-LEVEL METER (RSLM)
The RSLM is a battery-operated,handheld,acoustic measurement
device specifically designed for Infinity R.A.B.O.S.On the face of
the instrument is a light-emitting diode (LED) bar graph that
indicates relative sound level.There are also indicators for
power-on,out-of-range signals and a low battery.
Track Title
1 Welcome
2 Set System Test Level
3 Set Subwoofer Test Level
4 100Hz Test
5 95Hz Test
6 90Hz Test
7 85Hz Test
8 80Hz Test
9 77Hz Test
10 72Hz Test
11 66Hz Test
12 63Hz Test
13 56Hz Test
14 52Hz Test
15 49Hz Test
16 46Hz Test
17 43Hz Test
18 40Hz Test
19 38Hz Test
20 35Hz Test
21 30Hz Test
22 26Hz Test
23 24Hz Test
24 22Hz Test
25 21Hz Test
26 20Hz Test
27 Intro to Quick Retest
28 Quick Retest 100Hz
29 Quick Retest 95Hz
30 Quick Retest 90Hz
31 Quick Retest 85Hz
Track Title
32 Quick Retest 80Hz
33 Quick Retest 77Hz
34 Quick Retest 72Hz
35 Quick Retest 66Hz
36 Quick Retest 63Hz
37 Quick Retest 56Hz
38 Quick Retest 52Hz
39 Quick Retest 49Hz
40 Quick Retest 46Hz
41 Quick Retest 43Hz
42 Quick Retest 40Hz
43 Quick Retest 38Hz
44 Quick Retest 35Hz
45 Quick Retest 30Hz
46 Quick Retest 26Hz
47 Quick Retest 24Hz
48 Quick Retest 22Hz
49 Quick Retest 21Hz
50 Quick Retest 20Hz
51 Final System Level Adjustment
52 Final Subwoofer Level Adjustment
53 Wide Band Pink Noise,Left
54 Wide Band Pink Noise,L+R
55 Wide Band Pink Noise,Right
56 Wide Band Pink Noise,L-R
57 Wide Band Pink Noise,Uncorrelated
58 1 to 4kHz Pink Noise,Left
59 1 to 4kHz Pink Noise,L+R
60 1 to 4kHz Pink Noise,Right
61 1 to 4kHz Pink Noise,Left-R
62 1 to 4kHz Pink Noise,Uncorrelated
FIGURE 3
R.A.B.O.S.Sound-Level Meter
Power
-1
-2
-3
-4
-5
-6
-7
-8
-9
-10
-11
-13
-15
-18
U-R
Batt
FIGURE 4
RSLM bar-graph indications
Contents of the R.A.B.O.S.Test CD
On
Under-range
Measurement
In-range
Over-range
Low
Battery
11
INTERMEZZO 1.2s
Initial System-Level Setting
The following steps will set the playback level of the system to
the correct level for all tests that follow.
Turn the system volume to minimum.
Cue the R.A.B.O.S.Test CD to Track 2 and press Pause II.This
track will produce band-limited pink noise in both the left and
right channels.
Press Play › . With the RSLM positioned as described above,
increase the system volume until the RSLM display indicates -10dB.
See Figure 5.
RSLM indicating the correct system
level to begin tests (-10dB)
When you have completed this
adjustment,press Pause II.
Setting the Subwoofer Test Level
Each of the following test tracks is about one minute
long.This is normally much longer than required.Press Pause II
or advance to the next test as soon as you are ready.
This step will set the subwoofer levels for measurement
purposes.The objective is to scale the subwoofers’output to
make full use of the RSLM indicator range.Scaling is optimum
when a 0dB reading is observed on the highest peak without
triggering the over-range indication.Later,you will rebalance
the subwoofers to the main speakers.
The Intermezzo subwoofers should be shipped with the three
R.A.B.O.S.controls,L,M and N,set to fully clockwise
positions,and all measurements should be conducted with their
level controls in this position.Confirm this setting before you
begin this test.The gain control K should be set to the mid
position (5).
Cue Track 3 and Pause II.Track 3 continuously steps through all
subwoofer test tones for approximately 1 minute.Each tone will
play just long enough for the RSLM to give a stable reading.
To get accurate measurements,it is necessary to play
the woofers quite loud.The 0dB indication is about 94dB.At this
level,frequencies below 100Hz can cause doors,windows,
furnishings and other objects in the room to vibrate.This
frequently results in clearly audible buzzes and/or rattles that
come and go as each test tone plays.Strong buzzes not only
sound bad,they can cause measurement errors.If you hear a
buzz or rattle during this test,it is highly recommended that you
locate the source and eliminate its effects.This is actually a
valuable room-diagnostic tool.
Press Play
›
.As Track 3 plays,watch the RSLM carefully.Watch
for peak readings.The peak reading may be no more than a brief
flash.Readjust the subwoofer’s gain control K until the peak
level observed is 0dB without triggering the over-range
indication.See Figure 6.
When finished,press Pause II.
Performing Low-Frequency Measurements
Read the following instructions fully before beginning
tests.
For the following steps,you will need a Measurement Template
and a pencil.
FIGURE 7
R.A.B.O.S. Measurement Template
FIGURE 5
FIGURE 6
Adjusting the subwoofer levels for a 0dB peak
12
INTERMEZZO 1.2s
Each of the following tracks produces a low-frequency test tone.
The range of these tests is from 100Hz down to 20Hz.The
frequency of each test is announced before it begins.The first
test is the highest frequency (100Hz);therefore,you will be
marking the template from right to left.Each frequency point is
listed across the bottom of the Measurement Template (this is
called the X-axis).See Figure 7 on the previous page.The
vertical scale on the left side of the template indicates relative
level,in dBs (the Y-axis).The template’s vertical scale matches
that of the RSLM bar graph.
Cue Track 4 and Pause II.
From now on,you will want to keep your CD player’s
remote control handy.
Press Play .As Track 4 plays,observe the level indicated on
the RSLM.
EXAMPLE:The test frequency is 100Hz and the level indicated is
-2dB.Find the intersection of 100Hz (X-axis) and -2dB (Y-axis).
Place a dot at that point.See Figure 8.
It takes a few seconds for the RSLM reading to stabilize,
especially at very low frequencies.Don’t rush.Give each test
adequate time for the meter to stabilize.
At the bottom of the bar graph is a green “ON”LED.This LED is
illuminated whenever the sound level is below the measuring
range of the RSLM.If this occurs during a test,place a dot at the
intersection of the test frequency and the bottom frame of the
template.See Figure 9.
When finished,press Skip to advance to the next test.
Repeat the process described above for Tracks 5 through 26.
When you have completed the 23 measurements,you are ready to
analyze the data and make corrective adjustments.The completed
Measurement template will look something like the example in
Figure 10.
Now connect the dots as shown in Figure 11.
This will make interpretation of the data much easier.
▼
FIGURE 8
Locating a test point
2
FIGURE 9
Indicating an under-range test
FIGURE 10
Completed R.A.B.O.S.template
FIGURE 11
Test example with dots connected
▼
▼
What Does a Parametric Equalizer Do?
The R.A.B.O.S.system uses one band of parametric equalization
for response correction.Parametric equalizers are the most
versatile class of filters.The effect an equalizer will have on the
signal is dependent on three parameters.
Frequency:The equalizer will have maximum effect at one
frequency,usually described as the center frequency.
Level:This refers to the amount of cut (in dBs) the equalizer
is set for.
Bandwidth: Defines the range of frequencies over which the
equalizer will have an effect.On the Intermezzo,this adjustment
is abbreviated as “Width.”
Only parametric equalizers allow independent adjustment of all
three parameters.
These will be explained more fully in the sections that follow.
Completing the Measurement Template
Along the bottom of the Measurement Template are three fields
where you will enter the equalizer settings needed to complete
system optimization.
These instructions are based on the example in Figure 11.Use
this tutorial to become familiar with the process.Strategies for
several other test results will be presented later.After you have
completed these three entry fields,you will be ready to perform
the adjustments,completing R.A.B.O.S.optimization.
Frequency
The frequency of the R.A.B.O.S.equalizer may be adjusted to
any one of nineteen frequencies from 20Hz to 80Hz.This defines
where you are going to apply equalization.
Width
The frequency range of the R.A.B.O.S.equalizer may be set from
5% to 50% of an octave in 21 steps.This setting defines
how much of the subwoofers’output will be equalized.
Width is expressed as a percentage of an octave.For example,a
width setting of 25% means the equalizer will affect a frequency
band of 1/4 of an octave;1/8 of an octave above and 1/8 of an
octave below the center frequency.
The octave is a logarithmic expression.From any point
in the spectrum,one octave above or below that point is always
double or half the frequency.Therefore,one octave above 100Hz
would be 200Hz.One octave below 100Hz is 50Hz.
In the section that follows,we will discuss the use of the
Width Selector.
FIGURE 12
Effect of adjustable width
INTERMEZZO 1.2s
13
14
INTERMEZZO 1.2s
Using the Width Selector
Read the following instructions carefully.The example
presented may not look like the graph you just created.
Focus on the concepts and techniques presented.Specific
cases will be discussed later.
You will use the Measurement Template just completed and the
Width Selector to determine the correct width setting.The Width
Selector graphically depicts a single resonant peak.The peak
looks similar to a slice of a pie.See Figure 13.At the top of the
Selector is a pull tab.When you slide the tab up and down,the
width of the pie slice becomes narrower and wider,respectively.
The pointers on the sides of the button point to the bandwidth
that corresponds to the width of the slice.
Place the Width Selector over the Measurement Template,
positioning the center rivet of the Selector over the response
peak,as shown in Figure 14.Be sure to align the horizontal lines
of the Width Selector with those of the Measurement Template.
Apply pressure to the upper and lower left corners of the
Selector using the thumb and forefinger of your left hand.Now
gently slide the tab up or down until the adjustable slice most
closely fits the response data.See Figure 15.
FIGURE 13
Width Selector
FIGURE 14
Placement of the
Bandwidth Selector
FIGURE 15
Selector adjusted for
the “best fit”
15
INTERMEZZO 1.2s
The pointer on the slider will indicate the correct width setting.
Enter this number in the Width field of the Measurement Template.
In our example,the width is 12.5%.
It is not realistic to expect a perfect fit.Acoustic
measurements encompass the behavior of not only the speakers
but of the room and its contents as well.Reflected energy,
standing waves and ambient noise all add their part.Determining
the best width setting nearly always requires compromise.
Level
This setting will define the amount (level) you want to reduce the
peak,in decibels.
The R.A.B.O.S.level adjustment is limited to attenuation only,and
is adjustable from 0dB to -14dB.After optimization,the R.A.B.O.S.
equalizer will eliminate the largest low-frequency peak;
therefore,the broadband bass level can be increased without
overpowering the midrange frequencies.R.A.B.O.S.applies this
compensation automatically.
You will use the Width Selector as an aid in determining the
correct level setting.Place the Width Selector as described
above and adjust it to the correct width.Observe the first
frequency point on the high-frequency side of the peak that no
longer follows the slope of the Width Selector.In this example
this is 56Hz.Calculate the average level of the readings from
56Hz up to 100Hz;that is,10 data points in this example.
Whenever your answer has a remainder,always round down
(disregarding the negative [-]) to the next whole number.
In our example,you would enter 9 in the attenuation field.
This may not be the best method in all cases.The next section
contains several other examples.
What You Measure,What To Do
As stated earlier,it is not possible to anticipate the effect of
every possible listening environment.However,most residential
sound rooms share many characteristics,and their dimensions
fall into a range that make some response irregularities far more
likely than others.On the following pages are examples of what
you may encounter.Following each example is a strategy for
correction.Compare your measurement results with the following
examples.Find the one that best fits your graph and follow the
instructions presented for that scenario.
Remember,when looking for a match,look at the
descriptive characteristics,not any specific frequency or level.
Each of these examples can occur at any frequency,bandwidth
and level.It is unlikely that your test results will be exactly as
depicted in these examples.
Example 1. Single Dominant Peak:
This is the most common result of speaker/room interaction.
Apply the Width Selector as described in Figure 14.Align the
center-line of the Selector over the center of the peak,as shown in
Figure 15.Now adjust the Selector until you have achieved the “best
fit.”The slider now points to the correct bandwidth setting.In this
example,the frequency is 43Hz and the best-fit width is 12.5%.Fill
in the Width and Frequency fields provided on the template.
Determine the appropriate level using the technique described
earlier.In this example,-9dB would be best.Enter the level in the
field provided.
Skip to the “Adjusting the R.A.B.O.S.Equalizer”
section on page 18.
FIGURE 16
Single dominant peak
56Hz 63Hz 66Hz 72Hz 77Hz 80Hz 85Hz 90Hz 95Hz 100Hz
-9 -10 -8 -9 -10 -9 -8 -10 -10 -9 -
92 ÷ 10 = -9.2
16
INTERMEZZO 1.2s
Example 2.Two Response Peaks:
Characterized by two response peaks,approximately equal in
amplitude and width.This requires that you make a choice
between the two peaks.In situations like this,the higher
frequency peak will always be more audible and objectionable.
Response peaks below 45Hz,unless extreme,can actually be
beneficial toward achieving visceral impact.Perform corrections
on the upper frequency peak.
Apply the Width Selector as described above.Align the center-line
of the Selector over the center of the higher frequency peak.Now
adjust the Selector until you have achieved the “best fit.”The slider
now points to the correct width setting.In this example,this is at
52Hz.The best-fit width is 28%.Fill in the Width and Frequency
fields provided on the template.
Determine the appropriate level using the technique described
earlier.This calculation will indicate a -8dB setting.However,this
peak does not reach the 0dB level as the lower peak does.
Therefore,a -8dB setting would be excessive.The 52Hz peak
stops at -2dB.Subtracting 2 from 8 yields the correct setting,
-6dB.Enter -6 in the Level field.
Skip to the “Adjusting the R.A.B.O.S.Equalizer”section on page 18.
Example 3.Peak Adjacent to a Dip:
Response dips can occur at any frequency,sometimes
immediately adjacent to the peak you want to correct.Two
examples are shown,one immediately above and one immediately
below the peak.Deep response dips such as these are caused by
destructive wave interference.Destructive interference dips occur
only in one spot within the room.It is not uncommon to completely
eliminate the effect by moving the RSLM to a different location.
Note that this does not eliminate the dips.We have simply moved
away from them.Sometimes only a few inches are required.
Do not attempt to correct this condition with equalization.
If you encounter dips like this,take the following steps:
FIGURE 17
Two response peaks
FIGURE 18
Dip above or below peak
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
Infinity 1.2s Manuel utilisateur
- Catégorie
- Subwoofers
- Taper
- Manuel utilisateur
- Ce manuel convient également à
dans d''autres langues
- English: Infinity 1.2s User manual
Documents connexes
-
Infinity Intermezzo 4.1t Le manuel du propriétaire
-
-
-
-
-
-
-
-
-
Autres documents
-
PSB CHS212 Manuel utilisateur
-
Broan NuTone 1103233B Manuel utilisateur
-
Velodyne Acoustics HGS 10 Manuel utilisateur
-
-
YORKVILLE POWERMAX 1622 Le manuel du propriétaire
-
Bosch Appliances XLA 3200 Manuel utilisateur
-
YORKVILLE AP812 Le manuel du propriétaire
-
Yorkville Sound AP312 Manuel utilisateur
-
YORKVILLE AP312 Le manuel du propriétaire
-
Jamo SUB 660 Le manuel du propriétaire
