Mitsubishi PEA-A12 Manuel utilisateur

Marque: Mitsubishi

Modèle: PEA-A12

Taper: Manuel utilisateur

Ce manuel convient également à

Air-Conditioners

PEA-A12, 18AA

OPERATION MANUAL

For safe and correct use, please read this operation manual thoroughly before operating the air-conditioner unit.

FOR USER

English

MANUEL D’UTILISATION

Pour une utilisation correcte sans risques, veuillez lire le manuel d’utilisation en entier avant de vous servir du

climatiseur.

POUR L’UTILISATEUR

Français

KB79M101H01_cover.pm6 08.9.4, 2:26 PM1

Contents

s Before installing the unit, make sure you read all the “Safety

Precautions”.

s The “Safety Precautions” provide very important points regard-

ing safety. Make sure you follow them.

s Please report to or take consent by the supply authority be-

fore connection to the system.

1. Safety Precautions

2. Parts Names

■ Indoor Unit

PEA-A·AA

Fan steps 3 steps

Vane –

Louver –

Filter Normal

Filter cleaning indication –

This symbol mark is for EU countries only.

This symbol mark is according to the directive 2002/96/EC Article 10 Information for users and Annex IV.

Your MITSUBISHI ELECTRIC product is designed and manufactured with high quality materials and components which can be

recycled and reused.

This symbol means that electrical and electronic equipment, at their end-of-life, should be disposed of separately from your house-

hold waste.

Please, dispose of this equipment at your local community waste collection/recycling centre.

In the European Union there are separate collection systems for used electrical and electronic product.

Please, help us to conserve the environment we live in!

Symbols used in the text

Warning:

Describes precautions that should be observed to prevent danger of

injury or death to the user.

Caution:

Describes precautions that should be observed to prevent damage

to the unit.

Symbols used in the illustrations

: Indicates a part which must be grounded.

Warning:

• The unit must not be installed by the user. Ask the dealer or an

authorized company to install the unit. If the unit is installed im-

properly, water leakage, electric shock or fire may result.

• Do not stand on, or place any items on the unit.

• Do not splash water over the unit and do not touch the unit with

wet hands. An electric shock may result.

• Do not spray combustible gas close to the unit. Fire may result.

• Do not place a gas heater or any other open-flame appliance where

it will be exposed to the air discharged from the unit. Incomplete

combustion may result.

• Do not remove the front panel or the fan guard from the outdoor

unit when it is running.

• When you notice exceptionally abnormal noise or vibration, stop

operation, turn off the power switch, and contact your dealer.

• Never insert fingers, sticks etc. into the intakes or outlets.

• If you detect odd smells, stop using the unit, turn off the power

switch and consult your dealer. Otherwise, a breakdown, electric

shock or fire may result.

• This air conditioner is NOT intended for use by children or infirm

persons without supervision.

• Young children must be supervised to ensure that they do not play

with the air conditioner.

•

If the refrigeration gas blows out or leaks, stop the operation of the

air conditioner, thoroughly ventilate the room, and contact your dealer.

Caution:

• Do not use any sharp object to push the buttons, as this may dam-

age the remote controller.

• Never block or cover the indoor or outdoor unit’s intakes or outlets.

Disposing of the unit

When you need to dispose of the unit, consult your dealer.

Note (Marking

for WEEE)

■ PEA-A·AA

Ceiling Concealed

1. Safety Precautions ................................................................ 2

2. Parts Names.......................................................................... 2

3. Screen Configuration............................................................. 4

4. Setting the Day of the Week and Time .................................. 4

5. Operation............................................................................... 5

6. Timer ..................................................................................... 6

7. Other Functions ..................................................................... 9

8. Function Selection ............................................................... 10

9. Care and Cleaning .............................................................. 14

10. Trouble Shooting ................................................................ 15

11. Installation, relocation and inspection ............................... 16

12. Specifications .................................................................... 17

Air outlet

Air intake

Filter

KB79M101H01_en.pm6 08.9.5, 5:26 PM2

■ Wired Remote-Controller

Display Section

For purposes of this explanation,

all parts of the display are shown

as lit. During actual operation, only

the relevant items will be lit.

˚F˚C

ERROR CODE

AFTER

TIMER

TIME SUN MON TUE WED THU FRI SAT

OFF

AFTER

FILTER

FUNCTION

ONLY1Hr.

WEEKLY

SIMPLE

AUTO OFF

Identifies the current operation

Shows the operating mode, etc.

* Multilanguage display is sup-

ported.

“Centrally Controlled” indicator

Indicates that operation of the re-

mote controller has been prohib-

ited by a master controller.

“Timer is Off” indicator

Indicates that the timer is off.

Temperature Setting

Shows the target temperature.

Day-of-Week

Shows the current day of the week.

Time/Timer Display

Shows the current time (the 12 hour clock or the 24

hour clock ), unless the simple or Auto Off timer is set.

If the simple or Auto Off timer is set, shows the time

remaining.

“Sensor” indication

Displayed when the remote controller

sensor is used.

“Locked” indicator

Indicates that remote controller but-

tons have been locked.

“Clean The Filter” indicator

Comes on when it is time to clean the

filter.

Timer indicators

The indicator comes on if the corre-

sponding timer is set.

Up/Down Air Direction indica-

tor

The indicator shows the direc-

tion of the outcoming airflow.

“One Hour Only” indicator

Displayed if the airflow is set to

weak and downward during COOL

or DRY mode. (Operation varies

according to model.)

The indicator goes off after one

hour, at which time the airflow di-

rection also changes.

Room Temperature display

Shows the room temperature. The room tempera-

ture display range is 46 °F [8 °C]–102 °F [39 °C].

The display flashes if the temperature is less than

46 °F [8 °C] or 102 °F [39 °C] or more.

Louver display

Indicates the action of the swing louver.

Does not appear if the louver is station-

ary.

(Power On indicator)

Indicates that the power is on.

Fan Speed indicator

Shows the selected fan speed.

Ventilation indicator

Appears when the unit is running in

Ventilation mode.

Operation Section

PAR-21MAA

ON/OFF

FILTER

CHECK

OPERATION

CLEAR

TEST

TEMP.

BACK DAY

MONITOR/SET

CLOCK

ON/OFF

Set Temperature buttons

Down

Timer Menu button

(Monitor/Set button)

Mode button (Return button)

Set Time buttons

Back

Ahead

Timer On/Off button

(Set Day button)

Opening the

door.

ON/OFF button

Fan Speed button

Filter button

(<Enter> button)

Test Run button

Check button (Clear button)

Airflow Up/Down button

Louver button

(

Operation button)

To preceding operation

number.

Ventilation button

(

Operation button)

To next operation

number.

2. Parts Names

Built-in temperature sensor

Note:

● “PLEASE WAIT” message

This message is displayed for approximately 3 minutes when power is supplied to the indoor unit or when the unit is recovering from a power failure.

● “NOT AVAILABLE” message

This message is displayed if a button is pressed to operate a function that the indoor unit does not have.

If a single remote controller is used to simultaneously operate multiple indoor units that are different models, this message will not be displayed if

any of the indoor units is equipped with the function.

KB79M101H01_en.pm6 08.9.5, 5:27 PM3

31-1/2

11-13/16+29/32

23-5/8

5-29/32

2-23/32

19-11/16

Note:

● The day and time will not appear if clock use has been disabled at Function

Selection of remote controller.

● After the power supply returns, the indoor unit does not operate for three

minutes. Above operation is normal.

● If the setting

1 or

2 is set, the 12 hour clock (AM/PM) will be displayed.

1CHANGE LANGUAGE setting = English [Refer to page 12]

2Temperature display setting =

°F [Refer to page 12]

If the settings above are not set, the 24 hour clock (rail road time/military

time) will be displayed.

Only “Set Day/Time”, “Standard Control Screens”, “Timer Monitor” and

“Timer Set UP” screens are applicable to the settings.

3. Screen Configuration

■ Outdoor Unit

■ A12, A18 (inch)

For details on setting the language for the remote controller display, refer

to section 8. Function Selection.

The initial language setting is English.

● Function Selection of remote controller:

Set the functions and ranges available to the re-

mote controller (timer functions, operating restric-

tions, etc.)

● Set Day/Time: Set the current day of the week or time.

● Standard Control Screens:

View and set the air conditioning system’s oper-

ating status

● Timer Monitor: View the currently set timer (weekly timer, sim-

ple timer, or Auto Off timer)

● Timer Setup: Set the operation of any of the timers (weekly

timer, simple timer, or Auto Off timer).

A :Hold down both the Mode button and the Timer On/Off button for 2

seconds.

B :Press the Timer Menu button.

C :Press the Mode (Return) button.

D :Press either of the Set Time buttons ( or ).

˚F˚F

TIMER

MON

OFF

WEEKLY

SUN MON TUE WED THU FRI SAT

WEEKLY

˚F˚F

˚F

TIME SUN

Function Selection of remote controller

Set Day/Time

Standard Control Screens

OFF ON

Timer Monitor Timer Setup

ADC

1. Press the or Set Time button A to show display 2.

2. Press the Timer On/Off (Set Day) button 9 to set the day.

* Each press advances the day shown at 3 : Sun → Mon → ... → Fri →

Sat.

3. Press the appropriate Set Time button A as necessary to set the time.

* As you hold the button down, the time (at 4) will increment first in

minute intervals, then in ten-minute intervals, and then in one-hour in-

tervals.

4. After making the appropriate settings at Steps 2 and 3, press the Filter

button 4 to lock in the values.

Note:

● Your new entries at Steps 2 and 3 will be cancelled if you press the Mode

(Return) button

2 before pressing the Filter

button

5. Press the Mode (Return) button 2 to complete the setting procedure.

This will return the display to the standard control screen, where 1 will

now show the newly set day and time.

4. Setting the Day of the Week and Time

Day of the Week &

Time display

˚F

TIME SUN

PAR-21MAA

ON/OFF

FILTER

CHECK

OPERATION

CLEAR

TEST

TEMP.

BACK DAY

MONITOR/SET

CLOCK

ON/OFF

Time Setting

TIME SUN

Day of the Week Setting

2. Parts Names

KB79M101H01_en.pm6 08.9.5, 5:27 PM4

˚F

PAR-21MAA

ON/OFF

FILTER

CHECK

OPERATION

CLEAR

TEST

TEMP.

BACK DAY

MONITOR/SET

CLOCK

ON/OFF

5. Operation

5.1. Description of “AUTO RESTART FUNCTION”

• This unit is equipped with the auto restart function. When the main power is

turned on, the air conditioner will start operation automatically in the same

mode as set with the remote controller before the shutoff of main power.

• If the unit was set to off with the remote controller before the shutoff of

main power, it will remain stopped even after the main power is turned on.

• If the unit was in the TEST RUN before the shutoff of main power, it will

start operation, at main power on, in the same mode as set with the

remote controller before the TEST RUN.

Mode

Temperature setting

Fan speed

Remote Controller settings

Last operation mode

Last set temperature

Last set fan speed

5.2. Turning ON/OFF

■ Press the ON/OFF button 1.

• The ON lamp 1 and the display area come on.

Note:

● When the unit is restarted, initial settings are as follows.

■ Press the ON/OFF button 1 again.

• The ON lamp 1 and the display area go dark.

Note:

Even if you press the ON/OFF button immediately after shutting down the op-

eration is progress, the air conditioner will not start for about three minutes.

This is to prevent the internal components from being damaged.

5.3. Mode select

■ If the unit is off, press the ON/OFF button to turn it on.

• 1 The ON indicator should light up.

■ Press the operation mode ( ) button 2 and select the opera-

tion mode 2.

Cooling mode

Drying mode

Fan mode

Heating mode

Automatic (cooling/heating) mode

Ventillation mode

Only indicated on the following condition

Wired remote controller used

LOSSNAY connected

Information for multi system air conditioner (Outdoor

unit: PUY, PUZ series)

sMulti system air conditioner (Outdoor unit: PUY, PUZ series) can

connect two or more indoor units with one outdoor unit. According

to the capacity, two or more units can operate simultaneously.

• When you try to operate two or more indoor units with one outdoor unit

simultaneously, one for the cooling and the other for heating, the opera-

tion mode of the indoor unit that operates earlier is selected. The other

indoor units that will start the operation later cannot operate, indicating

an operation state in flashing.

In this case, please set all the indoor units to the same operation mode.

• There might be a case that the indoor unit, which is operating in

(AUTO) mode. Cannot change over to the operating mode (COOL ↔

HEAT) and becomes a state of standby.

• When indoor unit starts the operation while the defrosting of outdoor

unit is being done, it takes a few minutes (max. about 15 minutes) to

blow out the warm air.

• In the heating operation, though indoor unit that does not operate may

get warm or the sound of refrigerant flowing may be heard, they are not

malfunction. The reason is that the refrigerant continuously flows into it.

Automatic operation

■ According to a set temperature, cooling operation starts if the room tem-

perature is too hot and heating operation starts if the room temperature

is too cold.

■ During automatic operation, if the room temperature changes and re-

mains 4 °F [2 °C] or more above the set temperature for 15 minutes, the

air conditioner switches to cooling mode. In the same way, if the room

temperature remains 4 °F [2 °C] or more below the set temperature for

15 minutes, the air conditioner switches to heating mode.

■ Because the room temperature is automatically adjusted in order to

maintain a fixed effective temperature, cooling operation is performed a

few degrees warmer and heating operation is performed a few degrees

cooler than the set room temperature once the temperature is reached

(automatic energy-saving operation).

Cooling mode

15 minutes (switches

from heating to cooling)

Set temperature +4 °F [2°C]

Set temperature

Set temperature -4 °F [2°C]

15 minutes (switches

from cooling to heating )

5.4. Temperature setting

sTo decrease the room temperature:

Press button 3 to set the desired temperature.

The selected temperature is displayed 3.

• Each time you press the button, the temperature value decreases by

2 °F [1 °C].

sTo increase the room temperature:

Press button 3 to set the desired temperature.

The selected temperature is displayed 3.

• Each time you press the button, the temperature value decreases by

2 °F [1 °C].

• Available temperature ranges are as follows:

Cooling/Drying: 67 °F [19 °C] - 86 °F [30 °C]

Heating: 63 °F [17 °C] - 83 °F [28 °C]

Automatic: 67 °F [19 °C] - 83 °F [28 °C]

• The display flashes either 47 °F [8 °C] - 103 °F [39 °C] to inform you if

the room temperature is lower or higher than the displayed temperature.

5.5. Fan speed setting

■ Press 5 button to select a desired fan speed.

• Each time you press the button, available options change with the

display 5 on the remote controller, as shown below.

Fan speed

Remote controller display

Low Medium High Auto

3-stage

▼

( )

▼

KB79M101H01_en.pm6 08.9.8, 7:30 PM5

5. Operation

6.1. For Wired Remote-controller

This section explains how to set and use the timer. You can use Function

Selection of remote controller to select which of three types of timer to use:

1 Weekly timer, 2 Simple timer, or 3 Auto Off timer.

For information about how to set the Function Selection of remote control-

ler, refer to section 8. [4]–3 (3).

6.1.1. Weekly Timer

■ The weekly timer can be used to set up to eight operations for each day

of the week.

• Each operation may consist of any of the following: ON/OFF time

together with a temperature setting, or ON/OFF time only, or tempera-

ture setting only.

• When the current time reaches a time set at this timer, the air

conditioner carries out the action set by the timer.

■ Time setting resolution for this timer is 1 minute.

Note:

*1. Weekly Timer/Simple Timer/Auto Off Timer cannot be used at the same time.

*2. The weekly timer will not operate when any of the following conditions is in

effect.

The timer feature is off; the system is in an malfunction state; a test run is

in progress; the remote controller is undergoing self-check or remote con-

troller check; the user is in the process of setting a function; the user is in

the process of setting the timer; the user is in the process of setting the

current day of the week or time; the system is under central control. (Spe-

cifically, the system will not carry out operations (unit on, unit off, or tem-

perature setting) that are prohibited during these conditions.)

˚F

SUN

WEEKLY

PAR-21MAA

ON/OFF

FILTER

CHECK

OPERATION

CLEAR

TEST

TEMP.

BACK DAY

MONITOR/SET

CLOCK

ON/OFF

42 3

A9 78

Operation No.

Day Setting

1. Be sure that you are at a standard control screen, and that the weekly

timer indicator 1 is shown in the display.

2. Press the Timer Menu button B, so that the “Set Up” appears on the

screen (at 2). (Note that each press of the button toggles the display

between “Set Up” and “Monitor”.)

3. Press the Timer On/Off (Set Day) button 9 to set the day. Each press

advances the display at 3 to the next setting, in the following sequence:

“Sun Mon Tues Wed Thurs Fri Sat” → “Sun” → ... → “Fri” → “Sat” → “Sun

Mon Tues Wed Thurs Fri Sat”...

4. Press the or Operation button (7 or 8) as necessary to select the

appropriate operation number (1 to 8) 4.

* Your inputs at Steps 3 and 4 will select one of the cells from the matrix

illustrated below.

(The remote-controller display at left shows how the display would

appear when setting Operation 1 for Sunday to the values indicated

below.)

6. Timer

5.6. Ventilation

sFor LOSSNAY combination

5.6.1. For Wired Remote-controller

● To run the ventilator together with the indoor unit:

■ Press the ON/OFF button 1.

• The Vent indication appears on the screen (at 8). The ventilator will

now automatically operate whenever the indoor unit is running.

● To run the ventilator independently:

■ Press the Mode button 2 until appears on the display. This will

cause the ventilator to start.

● To change the ventilator force:

■ Press the Ventilation button 8 as necessary.

• Each press toggles the setting, as shown below.

Note:

By setting the day to “Sun Mon Tues Wed Thurs Fri Sat”, you can set the same

operation to be carried out at the same time every day.

(Example: Operation 2 above, which is the same for all days of the week.)

˚F

SUN

WEEKLY

Shows the selected operation (ON or OFF)

* Does not appear if operation is not set.

Shows the temperature setting

* Does not appear if temperature is not

set.

Shows the time

setting

The display and the fan speed of the unit will differ in the following situa-

tions:

• When STAND BY and DEFROST are displayed.

• Just after the heating mode (while waiting to change to another mode).

• When the temperature of the room is higher than the temperature set-

ting of the unit operating in the heating mode.

• In the dry operation, the indoor fan automatically turns to low-speed

operation. Switching of fan speed is impossible.

• When the temperature of the heat exchanger is low in the heating mode

(e.g., immediately after heating operation starts).

Note:

● In the following cases, the actual fan speed generated by the unit will differ

from the speed shown the remote controller display.

1. While the display is showing “STAND BY” or “DEFROST”.

2. When the temperature of the heat exchanger is low in the heating mode.

(e.g. immediately after heating operation starts)

3. In HEAT mode, when room temperature is higher than the temperature

setting.

4. When the unit is in DRY mode.

▲

Low High

Op No. Sunday Monday … Saturday

No. 1

No. 2

…

No. 8

• 8:30

• ON

• 73 °F [23 °C]

• 10:00

• OFF

• 10:00

• OFF

• 10:00

• OFF

• 10:00

• OFF

▲

Setup Matrix

Start the air conditioner at 8:30, with

the temperature set to 73 °F [23 °C].

▲

Turn off the air conditioner at 10:00.

KB79M101H01_en.pm6 08.9.8, 7:30 PM6

6. Timer

5. Press the appropriate Set Time button A as necessary to set the

desired time (at 5).

* As you hold the button down, the time first increments in minute inter-

vals, then in ten-minute intervals, and then in one-hour intervals.

6. Press the ON/OFF button 1 to select the desired operation (ON or

OFF), at 6.

* Each press changes the next setting, in the following sequence:

No display (no setting) → “ON” → “OFF”

6.1.2. Simple Timer

■ You can set the simple timer in any of three ways.

• Start time only:

The air conditioner starts when the set time has elapsed.

• Stop time only:

The air conditioner stops when the set time has elapsed.

• Start & stop times:

The air conditioner starts and stops at the respective elapsed times.

■ The simple timer (start and stop) can be set only once within a 72-hour

period.

The time setting is made in hour increments.

Note:

*1. Weekly Timer/Simple Timer/Auto Off Timer cannot be used at the same time.

*2. The simple timer will not operate when any of the following conditions is in

effect.

The timer is off; the system is in malfunction state; a test run is in progress;

the remote controller is undergoing self-check or remote controller check;

the user is in the process of selecting a function; the user is in the process

of setting the timer; the system is under central control. (Under these con-

ditions, On/Off operation is prohibited.)

ONHr

AFTER

SIMPLE

PAR-21MAA

ON/OFF

FILTER

CHECK

OPERATION

CLEAR

TEST

TEMP.

BACK DAY

MONITOR/SET

CLOCK

ON/OFF

2A9

Action (On or Off)

* “— —” is displayed if there is no

setting.

1. Be sure that you are at a standard control screen, and that the simple

timer indicator is visible in the display (at 1).

When something other than the Simple Timer is displayed, set it to

SIMPLE TIMER using the function selection of remote controller (see

8.[4]–3 (3)) timer function setting.

2. Press the Timer Menu button B, so that the “Set Up” appears on the

screen (at 2). (Note that each press of the button toggles the display

between “Set Up” and “Monitor”.)

3. Press the ON/OFF button 1 to display the current ON or OFF simple

timer setting. Press the button once to display the time remaining to ON,

and then again to display the time remaining to OFF. (The ON/OFF

indication appears at 3).

• “ON” timer:

The air conditioner will start operation when the specified number of

hours has elapsed.

• “OFF” timer:

The air conditioner will stop operation when the specified number of

hours has elapsed.

4. With “ON” or “OFF” showing at 3: Press the appropriate Set Time button

A as necessary to set the hours to ON (if “ON” is displayed) or the hours

to OFF (if “OFF” is displayed) at 4.

• Available Range: 1 to 72 hours

5. To set both the ON and OFF times, repeat Steps 3 and 4.

* Note that ON and OFF times cannot be set to the same value.

6. To clear the current ON or OFF setting: Display the ON or OFF setting

(see step 3) and then press the Check (Clear) button 0 so that the time

setting clears to “—” at 4. (If you want to use only an ON setting or only

an OFF setting, be sure that the setting you do not wish to use is shown

as “—”.)

˚F

TIME SUN

WEEKLY

˚F

TIME SUN

WEEKLY

7. Press the appropriate Set Temperature button 3 to set the desired

temperature (at 7).

* Each press changes the setting, in the following sequence: No

display (no setting) ⇔ 76 °F [24 °C] ⇔ 78 °F [25 °C] ⇔ ... ⇔

84 °F [29 °C] ⇔ 86 °F [30 °C] ⇔ 54 °F [12 °C] ⇔ ... ⇔ 74 °F

[23 ° C] ⇔ No display.

(Available range: The range for the setting is 54 °F [12 °C] to 86 °F [30

°C]. The actual range over which the temperature can be controlled,

however, will vary according to the type of the connected unit.)

8. After making the appropriate settings at Steps 5, 6 and 7, press the

Filter button 4 to lock in the values.

To clear the currently set values for the selected operation, press and

quickly release the Check (Clear) button 0 once.

* The displayed time setting will change to “—:—”, and the On/Off

and temperature settings will all disappear.

(To clear all weekly timer settings at once, hold down the Check

(Clear) button 0 for two seconds or more. The display will begin

flashing, indicating that all settings have been cleared.)

Note:

Your new entries will be cancelled if you press the Mode (Return) button 2

before pressing the Filter

button 4.

If you have set two or more different operations for exactly the same time,

only the operation with the highest Operation No. will be carried out.

9. Repeat Steps 3 to 8 as necessary to fill as many of the available cells

as you wish.

10.Press the mode (Return) button 2 to return to the standard control

screen and complete the setting procedure.

11.To activate the timer, press the Timer On/Off button 9, so that the

“Timer Off” indication disappears from the screen. Be sure that the

“Timer Off” indication is no longer displayed.

* If there are no timer settings, the “Timer Off” indication will flash on

the screen.

Be sure that the weekly timer indicator is visible on the screen (at 1).

2. Press the Timer Menu button B so that “Monitor” is indicated on the

screen (at 8).

3. Press the Timer On/Off (Set Day) button 9 as necessary to select

the day you wish to view.

4. Press the or Operation button (7 or 8) as necessary to change

the timer operation shown on the display (at 9).

* Each press will advance to the next timer operation, in order of

time setting.

5. To close the monitor and return to the standard control screen, press

the Mode (Return) button 2.

Press the Timer On/Off button 9 so that “Timer Off” appears at 0.

Timer Settings

˚F

TIMER

SUN

OFF

WEEKLY

ONHr

AFTER

SIMPLE

Timer Setting

Press the Timer On/Off button 9 so that the “Timer Off” indication (at 0)

goes dark.

KB79M101H01_en.pm6 08.9.8, 7:30 PM7

6. Timer

7. After completing steps 3 to 6 above, press the Filter button 4 to lock

in the value.

Note:

Your new settings will be cancelled if you press the Mode (Return) button 2

before pressing the Filter

button 4.

8. Press the Mode (Return) button 2 to return to the standard control

screen.

9. Press the Timer On/Off button 9 to start the timer countdown. When the

timer is running, the timer value is visible on the display. Be sure that the

timer value is visible and appropriate.

TIMER ON

OFF

AFTER

SIMPLE

1. Be sure that the simple timer indicator is visible on the screen (at 1).

2. Press the Timer Menu button B, so that the “Monitor” appears on the

screen (at 5).

• If the ON or OFF simple timer is running, the current timer value will

appear at 6.

• If ON and OFF values have both been set, the two values appear

alternately.

3. Press the Mode (Return) button 2 to close the monitor display and return

to the standard control screen.

Press the Timer On/Off button 9 so that the timer setting no longer ap-

pears on the screen (at 7).

Timer Setting

˚F

SIMPLE

˚F

ONHr

AFTER

SIMPLE

Press the Timer On/Off button 9 so that the timer setting becomes visible

at 7.

Examples

If ON and OFF times have both been set at the simple timer, operation and

display are as indicated below.

Example 1:

Start the timer, with ON time set sooner than OFF time

ON Setting: 3 hours

OFF Setting: 7 hours

ONHr

AFTER

SIMPLE

˚F

OFF

AFTER

SIMPLE

˚F

OFF

AFTER

SIMPLE

ONHr

AFTER

SIMPLE

▲

At 3 hours after timer start

Display changes to show the timer’s OFF set-

ting (hours remaining to OFF).

The time displayed is OFF setting (7 hours) –

ON setting (3 hours) = 4 hours.

At Timer Start

Display shows the timer’s ON setting (hours

remaining to ON).

At 7 hours after timer start

The air conditioner goes off, and will remain off

until someone restarts it.

˚F

SIMPLE

▲

At 2 hours after timer start

Display changes to show the timer’s ON setting

(hours remaining to ON).

The time displayed is ON setting (5 hours) –

OFF setting (2 hours) = 3 hours.

At Timer Start

Display shows the timer’s OFF setting (hours

remaining to OFF).

At 5 hours after timer start

The air conditioner comes on, and will continue

to run until someone turns it off.

6.1.3. Auto Off Timer

■ This timer begins countdown when the air conditioner starts, and shuts

the air conditioner off when the set time has elapsed.

■ Available settings run from 30 minutes to 4 hours, in 30-minute intervals.

Note:

*1. Weekly Timer/Simple Timer/Auto Off Timer cannot be used at the same time.

*2. The Auto Off timer will not operate when any of the following conditions is

in effect.

The timer is off; the system is in malfunction state; a test run is in progress;

the remote controller is undergoing self-check or remote controller check;

the user is in the process of selecting a function; the user is in the process

of setting the timer; the system is under central control. (Under these con-

ditions, On/Off operation is prohibited.)

AFTER OFF

AUTO OFF

PAR-21MAA

ON/OFF

FILTER

CHECK

OPERATION

CLEAR

TEST

TEMP.

BACK DAY

MONITOR/SET

CLOCK

ON/OFF

2A9

AFTER OFF

AUTO OFF

Timer Setting

1. Be sure that you are at a standard control screen, and that the Auto Off

timer indicator is visible in the display (at 1).

When something other than the Auto Off Timer is displayed, set it to

AUTO OFF TIMER using the function selection of remote controller (see

8.[4]–3 (3)) timer function setting.

2. Hold down the Timer Menu button B for 3 seconds, so that the “Set Up”

appears on the screen (at 2).

(Note that each press of the button toggles the display between “Set Up”

and “Monitor”.)

3. Press the appropriate Set Time button A as necessary to set the OFF

time (at 3).

4. Press the Filter button 4 to lock in the setting.

Note:

Your entry will be cancelled if you press the Mode (Return) button 2 before

pressing the Filter

button 4.

5. Press the Mode (Return) button 2 to complete the setting procedure and

return to the standard control screen.

6. If the air conditioner is already running, the timer starts countdown

immediately. Be sure to check that the timer setting appears cor-

rectly on the display.

Example 2:

Start the timer, with OFF time is sooner than ON time

ON Setting: 5 hours

OFF Setting: 2 hours

KB79M101H01_en.pm6 08.9.5, 5:27 PM8

6. Timer

1. Be sure that the “Auto Off” is visible on the screen (at 1).

2. Hold down the Timer Menu button B for 3 seconds, so that “Monitor” is

indicated on the screen (at 4).

• The timer remaining to shutdown appears at 5.

3. To close the monitor and return to the standard control screen, press the

Mode (Return) button 2.

● Hold down the Timer On/Off button 9 for 3 seconds, so that “Timer Off”

appears (at 6) and the timer value (at 7) disappears.

˚F

AUTO OFF

˚F

AFTER OFF

AUTO OFF

● Hold down the Timer On/Off button 9 for 3 seconds. The “Timer Off”

indication disappears (at 6), and the timer setting comes on the display

(at 7).

● Alternatively, turn on the air conditioner. The timer value will appear at 7.

AFTER

TIMER

OFF

AUTO OFF

Timer Setting

● Alternatively, turn off the air conditioner itself. The timer value (at 7) will

disappear from the screen.

7. Other Functions

˚F

TIME SUN

FUNCTION

PAR-21MAA

ON/OFF

FILTER

CHECK

OPERATION

CLEAR

TEST

TEMP.

BACK DAY

MONITOR/SET

CLOCK

ON/OFF

Lock Indicator

7.1. Locking the Remote Controller Buttons (Operation

function limit controller)

■ If you wish, you can lock the remote controller buttons. You can use the

Function Selection of remote controller to select which type of lock to use.

(For information about selecting the lock type, see section 8, item [4]–2

(1)).

Specifically, you can use either of the following two lock types.

1Lock All Buttons:

Locks all of the buttons on the remote controller.

2Lock All Except ON/OFF:

Locks all buttons other than the ON/OFF button.

Note:

The “Locked” indicator appears on the screen to indicate that buttons are cur-

rently locked.

1. While holding down the Filter button 4, press and hold down the ON/OFF

button 1 for 2 seconds. The “Locked” indication appears on the screen

(at 1), indicating that the lock is now engaged.

* If locking has been disabled in Function Selection of remote controller,

the screen will display the “Not Available” message when you press the

buttons as described above.

˚F

FUNCTION

˚F

FUNCTION

˚F

• If you press a locked button, the “Locked” indication (at 1) will blink

on the display.

1. While holding down the Filter button 4, press and hold down the ON/OFF

button 1 for 2 seconds—so that the “Locked” indication disappears from

the screen (at 1).

ON/OFF

TEMP.

˚F

ON/OFF

TEMP.

˚F

7.2. Other indications

7.2.1. Centrally Controlled

■ When flashes continuously

Displayed when another indoor unit connected to the outdoor unit is

already operating in a different operation mode.

Match with the operation mode of the other indoor unit.

■ When mode switched after display flashes

Displayed when operation mode is restricted for each season by central

controller, etc.

Use another operation mode.

● Displayed when operation is controlled by central controller, etc.

Restricted operations are shown below.

• ON/OFF (including timer operation)

• Operation mode

• Set temperature

Note:

May also be individually restricted.

7.2.2. Flashing Mode Indicator

KB79M101H01_en.pm6 08.9.5, 5:27 PM9

7. Other Functions

ON/OFF

ERROR CODE

If you have entered contact number to be called in the event of a prob-

lem, the screen displays this number. (You can set this up under Func-

tion Selection of remote controller. For information, refer to section 8.)

Indoor Unit’s

Refrigerant

Address

Error Code

Indoor Unit No.

Alternating

Display

ON/OFF

˚F

ERROR CODE

ON/OFF

CALL:XXXX

XXX:XXX

Error Code

When the Check button is pressed:

ON lamp

(Flashing)

7.2.3. Error Codes indication

● If the ON lamp and error code are both flashing: This means that the air

conditioner is out of order and operation has been stopped (and cannot

resume). Take note of the indicated unit number and error code, then

switch off the power to the air conditioner and call your dealer or servicer.

● If only the error code is flashing (while the ON lamp remains lit): Opera-

tion is continuing, but there may be a problem with the system. In this

case, you should note down the error code and then call your dealer or

servicer for advice.

* If you have entered contact number to be called in the event of a

problem, push the Check button to display it on the screen. (You can

set this up under Function Selection of remote controller. For infor-

mation, refer to section 8.)

8. Function Selection

Function selection of remote controller

The setting of the following remote controller functions can be changed using the remote controller function selection mode. Change the setting when

needed.

Item 1

1. Change Language

(“CHANGE

LANGUAGE”)

2. Function limit

(“FUNCTION

SELECTION”)

3. Mode selection

(“MODE SELEC-

TION”)

4. Display change

(“DISP MODE

SETTING”)

Item 2

Language setting to display

(1) Operation function limit setting (operation lock) (“LOCKING

FUNCTION”)

(2) Use of automatic mode setting (“SELECT AUTO MODE”)

(3) Temperature range limit setting (“LIMIT TEMP FUNCTION”)

(4) Use of automatic filter elevation panel up/down operation

mode setting

(5) Use of fixed airflow direction mode setting

(1) Remote controller main/sub setting (“CONTROLLER MAIN/

SUB”)

(2) Use of clock setting (“CLOCK”)

(3) Timer function setting (“WEEKLY TIMER”)

(4) Contact number setting for error situation (“CALL.”)

(1) Temperature display °C/°F setting (“TEMP MODE °C/°F”)

(2) Suction air temperature display setting (“ROOM TEMP DISP

SELECT”)

(3) Automatic cooling/heating display setting (“AUTO MODE

DISP C/H”)

Item 3 (Setting content)

• Display in multiple languages is possible

• Setting the range of operation limit (operation lock)

• Setting the use or non-use of “automatic” operation mode

• Setting the temperature adjustable range (maximum, minimum)

(For this model, this function is not available.)

• Selecting main or sub remote controller

* When two remote controllers are connected to one group, one controller

must be set to sub.

• Setting the use or non-use of clock function

• Setting the timer type

• Contact number display in case of error

• Setting the telephone number

• Setting the temperature unit (°F or °C) to display

• Setting the use or non-use of the display of indoor (suction) air tempera-

ture

• Setting the use or non-use of the display of “Cooling” or “Heating” display

during operation with automatic mode

KB79M101H01_en.pm6 08.9.5, 5:27 PM10

8. Function Selection

[Function selection flowchart]

Setting language (English)

OFF

on1

on2

OFF

CALL-

OFF

°C

°F

PAR-21MAA

ON/OFF

FILTER

CHECK

OPERATION

CLEAR

TEST

TEMP.

BACK DAY

MONITOR/SET

CLOCK

ON/OFF

English

Germany

Spanish

Russian

Italy

Chinese

French

Japanese

Hold down the E button and press the D button for 2 seconds.

Remote controller function selection mode

E Press the operation mode button.

G Press the TIMER MENU button.

D Press the TIMER ON/OFF button.

Item1 Item2

Dot display

Item3

Room air temperature is not displayed.

One of “Automatic cooling” and “Automatic heating” is displayed

under the automatic mode is running. (Initial setting value)

Only “Automatic” is displayed under the automatic mode.

Normal display

(Display when the air condition is not running)

Change

Language

Function

selection

Mode

selection

Display

mode setting

Operation lock setting is not used.

(Initial setting value)

Operation lock setting is except On/Off button.

Operation lock setting is All buttons.

The automatic mode is displayed when the operation mode is

selected. (Initial setting value)

The automatic mode is not displayed when the operation mode

is selected.

The temperature range limit is not active. (Initial setting value)

The temperature range can be changed on cooling/dry mode.

The temperature range can be changed on heating mode.

The temperature range can be changed on automatic mode.

The remote controller will be the main controller. (Initial setting value)

The remote controller will be the sub controller.

The clock function can be used. (Initial setting value)

The clock function can not be used.

Weekly timer can be used. (Initial setting value)

Auto off timer can be used.

Simple timer can be used.

Timer mode can not be used.

The set contact numbers are not displayed in case of error.

(Initial setting value)

The set contact numbers are displayed in case of error.

The temperature unit °C is used. (Initial setting value)

The temperature unit °F is used.

Room air temperature is displayed. (Initial setting value)

*) For this model, this function is not available.

KB79M101H01_en.pm6 08.9.5, 5:27 PM11

8. Function Selection

[Detailed setting]

[4]–1. CHANGE LANGUAGE setting

The language that appears on the dot display can be selected.

• Press the [ MENU] button G to change the language.

1 English (GB), 2 German (D), 3 Spanish (E), 4 Russian (RU),

5 Italian (I), 6 Chinese (CH), 7 French (F), 8 Japanese (JP)

Refer to the dot display table.

[4]–2. Function limit

(1) Operation function limit setting (operation lock)

• To switch the setting, press the [ ON/OFF] button D.

1 no1: Operation lock setting is made on all buttons other than the

[ ON/OFF] button.

2 no2: Operation lock setting is made on all buttons.

3 OFF (Initial setting value): Operation lock setting is not made.

* To make the operation lock setting valid on the normal screen, it is

necessary to press buttons (Press and hold down the [FILTER] and

[ ON/OFF] buttons at the same time for two seconds.) on the

normal screen after the above setting is made.

(2) Use of automatic mode setting

When the remote controller is connected to the unit that has automatic

operation mode, the following settings can be made.

• To switch the setting, press the [ ON/OFF] button D.

1 ON (Initial setting value):

The automatic mode is displayed when the operation mode is

selected.

2 OFF:

The automatic mode is not displayed when the operation mode

is selected.

(3) Temperature range limit setting

After this setting is made, the temperature can be changed within the

set range.

• To switch the setting, press the [ ON/OFF] button D.

1 LIMIT TEMP COOL MODE:

The temperature range can be changed on cooling/dry mode.

2 LIMIT TEMP HEAT MODE:

The temperature range can be changed on heating mode.

3 LIMIT TEMP AUTO MODE:

The temperature range can be changed on automatic mode.

4 OFF (initial setting): The temperature range limit is not active.

* When the setting, other than OFF, is made, the temperature range

limit setting on cooling, heating and automatic mode is made at the

same time. However, the range cannot be limited when the set

temperature range has not changed.

• To increase or decrease the temperature, press the [ TEMP. ( )

or ( )] button F.

• To switch the upper limit setting and the lower limit setting, press the

[ ] button H. The selected setting will flash and the temperature

can be set.

• Settable range

Cooling/Dry mode:

Lower limit: 67 °F [19 °C] ~ 86 °F [30 °C]

Upper limit: 86 °F [30 °C] ~ 67 °F [19 °C]

Heating mode:

Lower limit: 63 °F [17 °C] ~ 83 °F [28 °C]

Upper limit: 83 °F [28 °C] ~ 63 °F [17 °C]

Automatic mode:

Lower limit: 67 °F [19 °C] ~ 83 °F [28 °C]

Upper limit: 83 °F [28 °C] ~ 67 °F [19 °C]

* The settable range varies depending on the unit to connect (Mr.

Slim units, CITY MULTI units, and intermediate temperature units)

(4) Use of automatic filter elevation panel up/down operation mode set-

ting

For this model, this function is not available.

(5) Use of fixed airflow direction mode setting

For this model, this function is not available.

[4]–3. Mode selection setting

(1) Remote controller main/sub setting

• To switch the setting, press the [ ON/OFF] button D.

1 Main: The controller will be the main controller.

2 Sub: The controller will be the sub controller.

(2) Use of clock setting

• To switch the setting, press the [ ON/OFF] button D.

1 ON: The clock function can be used.

2 OFF: The clock function cannot be used.

(3) Timer function setting

• To switch the setting, press the [ ON/OFF] button D (Choose one

of the followings.).

1 WEEKLY TIMER (initial setting value):

The weekly timer can be used.

2 AUTO OFF TIMER:

The auto off timer can be used.

3 SIMPLE TIMER:

The simple timer can be used.

4 TIMER MODE OFF:

The timer mode cannot be used.

* When the use of clock setting is OFF, the “WEEKLY TIMER” cannot

be used.

(4) Contact number setting for error situation

• To switch the setting, press the [ ON/OFF] button D.

1 CALL OFF:

The set contact numbers are not displayed in case of error.

2 CALL **** *** ****:

The set contact numbers are displayed in case of error.

CALL_:

The contact number can be set when the display is as shown on

the left.

• Setting the contact numbers

To set the contact numbers, follow the following procedures.

Move the flashing cursor to set numbers. Press the [ TEMP.

( ) and ( )] button F to move the cursor to the right (left). Press

the [ CLOCK ( ) and ( )] button C to set the numbers.

[4]–4. Display change setting

(1) Temperature display °C/°F setting

• To switch the setting, press the [ ON/OFF] button D.

1 °C: The temperature unit °C is used.

2 °F: The temperature unit °F is used.

(2) Suction air temperature display setting

• To switch the setting, press the [ ON/OFF] button D.

1 ON: The suction air temperature is displayed.

2 OFF: The suction air temperature is not displayed.

(3) Automatic cooling/heating display setting

• To switch the setting, press the [ ON/OFF] button D.

1 ON:

One of “Automatic cooling” and “Automatic heating” is displayed

under the automatic mode is running.

2 OFF:

Only “Automatic” is displayed under the automatic mode.

KB79M101H01_en.pm6 08.9.5, 5:27 PM12

8. Function Selection

[Dot display table]

Waiting for start-up

Operation mode Cool

Dry

Heat

Auto

Auto(Cool)

Auto(Heat)

Fan

Ventilation

Stand by

(Hot adjust)

Defrost

Set temperature

Fan speed

Not use button

Check (Error)

Test run

Self check

Unit function selection

Setting of ventilation

Selecting language

English Germany Spanish Russian Italy Chinese French Japanese

CHANGE LANGUAGE

Function selection

Operation function limit setting

Use of automatic mode setting

Temperature range limit setting

Use of automatic filter elevation panel

up/down operation mode setting

Use of fixed airflow direction mode

setting

Limit temperature cooling/day

mode

Limit temperature heating mode

Limit temperature auto mode

Mode selection

Remote controller setting MAIN

Remote controller setting SUB

Use of clock setting

Setting the day of the week and

time

Timer set

Timer monitor

Weekly timer

Timer mode off

Auto off timer

Simple timer

Selecting language

English Germany Spanish Russian Italy Chinese French Japanese

KB79M101H01_en.pm6 08.9.5, 5:27 PM13

ON/OFF

TEMP.

˚F

FILTER

■ Indicates that the filter needs cleaning.

Clean the filter.

■ When resetting “FILTER” display

When the [FILTER] button is pressed two times successively after

cleaning the filter, the display goes off and is reset.

Note:

● When two or more different types of indoor unit are controlled, the cleaning

period differs with the type of filter. When the master unit cleaning period

arrives, “FILTER” is displayed. When the filter display goes off, the cumula-

tive time is reset.

● “FILTER” indicates the cleaning period when the air conditioner was used

under general indoor air conditions by criteria time. Since the degree of dirti-

ness depends on the environmental conditions, clean the filter accordingly.

● The filter cleaning period cumulative time differs with the model.

● This indication is not available for wireless remote controller.

sCleaning the filters

• Clean the filters using a vacuum cleaner. If you do not have a vacuum

cleaner, tap the filters against a solid object to knock off dirt and dust.

• If the filters are especially dirty, wash them in lukewarm water. Take care

to rinse off any detergent thoroughly and allow the filters to dry com-

pletely before putting them back into the unit.

Caution:

• Do not dry the filters in direct sunlight or by using a heat source,

such as an electric heater: this may warp them.

• Do not wash the filters in hot water (above 122 °F [50 °C]), as this

may warp them.

• Make sure that the air filters are always installed. Operating the

unit without air filters can cause malfunction.

Caution:

• Before you start cleaning, stop operation and turn OFF the power

supply.

• Indoor units are equipped with filters to remove the dust of sucked-in

air. Clean the filters using the methods shown in the following sketches.

9. Care and Cleaning

sFilter removal

Caution:

• In removing the filter, precautions must be taken to protect your

eyes from dust. Also, if you have to climb up on a stool to do the

job, be careful not to fall.

• When the filter is removed, do not touch the metallic parts inside

the indoor unit, otherwise injury may result.

■ PEA-A·AA

• While lifting the filter knob, pull it.

A Air intake B Air outlet C Filter D Knob

Contact number setting of error

situation

Display change

Temperature display °C/°F setting

Room air temperature display

setting

Automatic cooling/heating display

setting

Selecting language

English Germany Spanish Russian Italy Chinese French Japanese

8. Function Selection

KB79M101H01_en.pm6 08.9.5, 5:27 PM14

10. Trouble Shooting

Having trouble?

Air conditioner does not heat or cool well.

When heating operation starts, warm air does not blow from the indoor unit

soon.

During heating mode, the air conditioner stops before the set room tem-

perature is reached.

When the airflow direction is changed, the vanes always move up and down

past the set position before finally stopping at the position.

A flowing water sound or occasional hissing sound is heard.

A cracking or creaking sound is heard.

The room has an unpleasant odor.

A white mist or vapor is emitted from the indoor unit.

Water or vapor is emitted from the outdoor unit.

The operation indicator does not appear in the remote controller display.

“ ” appears in the remote controller display.

When restarting the air conditioner soon after stopping it, it does not oper-

ate even though the ON/OFF button is pressed.

Air conditioner operates without the ON/OFF button being pressed.

Air conditioner stops without the ON/OFF button being pressed.

Remote controller timer operation cannot be set.

“PLEASE WAIT” appears in the remote controller display.

An error code appears in the remote controller display.

Draining water or motor rotation sound is heard.

Here is the solution. (Unit is operating normally.)

■ Clean the filter. (Airflow is reduced when the filter is dirty or clogged.)

■ Check the temperature adjustment and adjust the set temperature.

■ Make sure that there is plenty of space around the outdoor unit. Is the

indoor unit air intake or outlet blocked?

■ Has a door or window been left open?

■ Warm air does not blow until the indoor unit has sufficiently warmed up.

■ When the outdoor temperature is low and the humidity is high, frost may

form on the outdoor unit. If this occurs, the outdoor unit performs a de-

frosting operation. Normal operation should begin after approximately

10 minutes.

■ When the airflow direction is changed, the vanes move to the set position

after detecting the base position.

■ These sounds can be heard when refrigerant is flowing in the air condi-

tioner or when the refrigerant flow is changing.

■ These sounds can be heard when parts rub against each due to expan-

sion and contraction from temperature changes.

■ The indoor unit draws in air that contains gases produced from the walls,

carpeting, and furniture as well as odors trapped in clothing, and then

blows this air back into the room.

■ If the indoor temperature and the humidity are high, this condition may

occur when operation starts.

■ During defrosting mode, cool airflow may blow down and appear like a

mist.

■ During cooling mode, water may form and drip from the cool pipes and

joints.

■ During heating mode, water may form and drip from the heat exchanger.

■ During defrosting mode, water on the heat exchanger evaporates and

water vapor may be emitted.

■

Turn on the power switch. “ ” will appear in the remote controller display.

■ During central control, “ ” appears in the remote controller display and

air conditioner operation cannot be started or stopped using the remote

controller.

■ Wait approximately three minutes.

(Operation has stopped to protect the air conditioner.)

■ Is the on timer set?

Press the ON/OFF button to stop operation.

■ Is the air conditioner connected to a central remote controller?

Consult the concerned people who control the air conditioner.

■ Does “ ” appear in the remote controller display?

Consult the concerned people who control the air conditioner.

■ Has the auto recovery feature from power failures been set?

Press the ON/OFF button to stop operation.

■ Is the off timer set?

Press the ON/OFF button to restart operation.

■ Is the air conditioner connected to a central remote controller?

Consult the concerned people who control the air conditioner.

■ Does “ ” appear in the remote controller display?

Consult the concerned people who control the air conditioner.

■ Are timer settings invalid?

If the timer can be set,

WEEKLY

SIMPLE

, or

AUTO OFF

appears in

the remote controller display.

■ The initial settings are being performed. Wait approximately 3 minutes.

■ The protection devices have operated to protect the air conditioner.

■ Do not attempt to repair this equipment by yourself.

Turn off the power switch immediately and consult your dealer. Be sure

to provide the dealer with the model name and information that appeared

in the remote controller display.

■ When cooling operation stops, the drain pump operates and then stops.

Wait approximately 3 minutes.

KB79M101H01_en.pm6 08.9.5, 5:49 PM15

10. Trouble Shooting

Having trouble? Here is the solution. (Unit is operating normally.)

Noise is louder than specifications.

Nothing appears in the wireless remote controller display, the display is

faint, or signals are not received by the indoor unit unless the remote con-

troller is close.

The operation lamp near the receiver for the wireless remote controller on

the indoor unit is flashing.

■ The indoor operation sound level is affected by the acoustics of the par-

ticular room as shown in the following table and will be higher than the

noise specification, which was measured in an echo-free room.

■ The batteries are low.

Replace the batteries and press the Reset button.

■ If nothing appears even after the batteries are replaced, make sure that

the batteries are installed in the correct directions (+, –).

■ The self diagnosis function has operated to protect the air conditioner.

■ Do not attempt to repair this equipment by yourself.

Turn off the power switch immediately and consult your dealer. Be sure

to provide the dealer with the model name.

High sound-

absorbing rooms

Broadcasting

studio, music

room, etc.

3 to 7 dB

Normal rooms

Reception room,

hotel lobby, etc.

6 to 10 dB

Low sound-

absorbing rooms

Office, hotel

room

9 to 13 dB

Location

examples

Noise levels

Installation place

Avoid installing the air conditioner in the following places.

• Where flammable gas could leak.

Caution:

Do not install the unit where flammable gas could leak.

If gas leaks and collects around the unit, it may cause an explosion.

• Where there is much machine oil.

• Salty place such as the seaside.

• Where sulfide gas is generated such as a hot spring.

• Where there is oil splashing or much oily smoke.

Warning:

If the air conditioner operates but does not cool or heat (depending

on model) the room, consult your dealer since there may be a refrig-

erant leak. Be sure to ask the service representative whether there is

refrigerant leakage or not when repairs are carried out.

The refrigerant charged in the air conditioner is safe. Refrigerant nor-

mally does not leak, however, if refrigerant gas leaks indoors, and

comes into contact with the fire of a fan heater, space heater, stove,

etc., harmful substances will be generated.

Inverter type

fluorescent lamp

To prevent the effect

of a fluorescent lamp,

keep it away as far

apart as possible.

To prevent picture

distortion or

noise, keep 1 m

[39-3/8 in] or

more apart.

Radio

100 mm [3-15/16 in]

or more

400 mm [15-3/4 in]

or more

Well-

ventilated dry

place

Wall, etc.

11. Installation, relocation and inspection

Electrical work

• Provide an exclusive circuit for power supply of the air conditioner.

• Be sure to observe the breaker capacity.

Warning:

• The customer should not install this unit. If the unit is installed incorrectly, fire, electric shock, injury due to a falling unit, water leakage, etc.

may result.

• Do not connect using branched outlet or an extension cord, and do not attach many loads to one electric outlet.

A fire or electric shock may result from poor contact, poor insulation, exceeding the permissible current, etc.

Consult your dealer.

Caution:

• Apply grounding

Do not connect a grounding wire to a gas pipe, water pipe, lightning rod or ground wire of a telephone.

If a grounding is incorrect, it may cause an electric shock.

• Install an earth leakage breaker depending on the place where the air conditioner is to be installed (humid place, etc.).

If the earth leakage breaker is not installed, it may cause an electric shock.

Inspection and maintenance

• When the air conditioner is used for several seasons, the capacity may be lowered due to dirt inside the unit.

• Depending upon the conditions of use, an odor may be generated or dirt, dust, etc. may prevent proper drainage.

• It is recommended to apply inspection and maintenance (charged) by a specialist in addition to normal maintenance. Consult your dealer.

KB79M101H01_en.pm6 08.9.5, 5:27 PM16

Also consider operation sound

• Do not put an object around the air outlet of the outdoor unit. It may cause lowering of capacity or increase operating sound.

• If abnormal sound is heard during operation, consult your dealer.

Relocation

• When the air conditioner is to be removed or reinstalled because of rebuilding, moving, etc., special techniques and work are required.

Warning:

Repair or relocation should not be done by the customer.

If this is done incorrectly, it may cause a fire, electric shock, injury by dropping of the unit, water leakage, etc. Consult your dealer.

Disposal

• To dispose of this product, consult your dealer.

If you have any question, consult your dealer.

11. Installation, relocation and inspection

12. Specifications

Notes: 1. Rating conditions (cooling) Indoor : 80

F [26.7

C] D.B., 67

F [19.4

C] W.B. Outdoor : 95

F [35

C] D.B.

2. Rating conditions (heating) Indoor : 70

F [21.1

C] D.B. Outdoor : 47

F [8.3

C] D.B., 43

F [6.1

C] W.B.

3. The capacity is indicated the value when one indoor unit is connected to the outdoor unit.

4. Specifications subject to change without notice.

5. The external static pressure is set to 15 Pa at factory shipment.

Guaranteed operating range

Cooling

Upper limit

Lower limit

Heating

Upper limit

Lower limit

PEA-A12AA

Cooling Heating

12,000 –

0.07 –

7-9-11

247-317-388

116-150-183

0.02-0.06-0.14-0.20

[5/15/35/50]

23-28-33

21 [48]

Model

Function

Power supply

Capacity BTU/h

Input kW

CMM

Airflow (Lo-Mid-Hi) CFM

L/S

Ext. static pressure

in. WG

[Pa]

Noise level (Lo-Mid-Hi) dB

Weight kg [Ib]

PEA-A18AA

Cooling Heating

22,000 23,200

0.09 0.07

12-15-18

423-529-635

200-250-300

0.02-0.06-0.14-0.20

[5/15/35/50]

30-34-38

27 [60]

~/N, 208/230V, 60Hz

Outdoor

115 °F [46 °C] D.B., –

23 °F [-5 °C] D.B., –

70 °F [21 °C] D.B., 59 °F [15 °C] W.B.

12 °F [-11 °C] D.B., 10 °F [-12 °C] W.B.

Indoor

90 °F [32 °C] D.B., 73 °F [23 °C] W.B.

66 °F [19 °C] D.B., 59 °F [15 °C] W.B.

83 °F [28 °C] D.B., –

63 °F [17 °C] D.B., –

Notes: 1. Units should be installed by licensed electric contractor accordingly to local code requirement.

2. For outdoor units to be connected, refer to the Installation Manual that comes with the units.

3. Single outdoor unit (either PUY-A12,18NHA

(1)

or PUZ-A18NHA ) will be connected to each indoor unit.

KB79M101H01_en.pm6 08.9.5, 5:27 PM17

Index

■ Unité interne

PEA-A·AA

Modes du ventilateur 3 modes

Ailette –

Louvre –

Filtre Normal

Témoin de nettoyage du filtre –

Ce symbole est utilisé uniquement pour les pays de l’UE.

Ce symbole est conforme à la directive 2002/96/EC Article 10 Informations à l’attention des usagers et Annexe IV.

Votre produit Mitsubishi Electric est conçu et fabriqué avec des matèriels et des composants de qualité supérieure qui peuvent être recyclés et réutilisés.

Ce symbole signifie que les équipements électriques et électroniques, à la fin de leur durée de service, doivent être éliminés séparément des ordures

ménagères.

Nous vous prions donc de confier cet équipement à votre centre local de collecte/recyclage.

Dans l’Union Européenne, il existe des systèmes sélectifs de collecte pour les produits électriques et électroniques usagés.

Aidez-nous à conserver l’environnement dans lequel nous vivons !

Remarque (Mar-

quage WEEE)

■ PEA-A·AA

Dissimulé dans le plafond

Grille de

refoulement d’air

Admission d’air

2. Nomenclature

s Avant d’installer le climatiseur, lire attentivement toutes les

“Consignes de sécurité”.

s Les “Consignes de sécurité” reprennent des points très im-

portants concernant la sécurité. Veillez bien à les suivre.

s Veuillez consulter ou obtenir la permission votre compagnie

d’électricité avant de connecter votre système.

1. Consignes de sécurité

Symboles utilisés dans le texte

Avertissement:

Précautions à suivre pour éviter tout danger de blessure ou de décès de l’utilisateur.

Précaution:

Décrit les précautions qui doivent être prises pour éviter d’endom-

mager l’appareil.

Symboles utilisés dans les illustrations

: Indique un élément qui doit être mis à la terre.

Avertissement:

• Cet appareil ne doit pas être installé par l’utilisateur. Demander au revendeur

ou à une société agréée de l’installer. Si l’appareil n’est pas correctement ins-

tallé il peut y avoir un risque de fuite d’eau, d’électrocution ou d’incendie.

• Ne pas marcher sur l’appareil ni y déposer des objets.

• Ne jamais éclabousser l’appareil ni le toucher avec des mains humides. Il

pourrait en résulter un risque d’électrocution.

• Ne pas vaporiser de gaz inflammable à proximité de l’appareil sous risque

d’incendie.

• Ne pas placer de chauffage au gaz ou tout autre appareil fonctionnant avec

une flamme vive là où il serait exposé à l’échappement d’air du climatiseur.

Cela risquerait de provoquer une mauvaise combustion.

• Ne pas retirer la face avant ou la protection du ventilateur de l’appareil exté-

rieur pendant son fonctionnement.

• Si vous remarquez des vibrations ou des bruits particulièrement anormaux,

arrêter l’appareil, éteindre l’interrupteur et prendre contact avec le revendeur.

• Ne jamais mettre des doigts, des bâtons, etc. dans les entrées et sorties d’air.

• Si vous sentez des odeurs étranges, arrêter l’appareil, le mettre hors tension

et contacter le revendeur. Si vous ne procédez pas de cette façon, il pourrait y

avoir risque de panne, d’électrocution ou d’incendie.

• Ne JAMAIS laisser des enfants ou des personnes handicapées utiliser le cli-

matiseur sans surveillance.

• Toujours surveiller que les jeunes enfants ne jouent pas avec le climatiseur.

• Si le gaz de réfrigérant fuit, arrêter le fonctionnement du climatiseur, aérer

convenablement la pièce et prendre contact avec le revendeur.

Précaution:

• Ne pas utiliser d’objet pointu pour enfoncer les boutons car cela risquerait

d’endommager la commande à distance.

• Ne jamais obstruer les entrées et sorties des appareils extérieurs et intéri-

eurs.

Rangement de l’appareil

Lorsque vous devez ranger l’appareil, veuillez consulter votre revendeur.

iltre

1. Consignes de sécurité ........................................................ 18

2. Nomenclature ...................................................................... 18

3. Configuration d’écran .......................................................... 20

4. Régler le jour de la semaine et l’heure ............................... 20

5. Fonctionnement .................................................................. 21

6. Minuterie ............................................................................. 22

7. Autres fonctions .................................................................. 25

8. Sélection des fonctions ....................................................... 26

9. Entretien et nettoyage ......................................................... 30

10. Guide de dépannage ........................................................ 31

11. Installation, deplacement et inspection ............................. 32

12. Spécifications techniques ................................................. 33

KB79M101H01_F.pm6 08.9.5, 5:25 PM18

■ Pour la télécommande à fil

PAR-21MAA

ON/OFF

FILTER

CHECK

OPERATION

CLEAR

TEST

TEMP.

BACK DAY

MONITOR/SET

CLOCK

ON/OFF

Remarque :

● Message “PLEASE WAIT” (VEUILLEZ PATIENTER)

Ce message s’affiche pendant 3 minutes environ lorsque l’appareil intérieur est alimenté ou suite à une coupure d’électricité.

● Message “NOT AVAILABLE” (INDISPONIBLE)

Ce message s’affiche quand vous appuyez sur une touche pour lancer une fonction qui est indisponible pour cet appareil intérieur.

Si une télécommande unique est utilisée pour contrôler simultanément plusieurs appareils intérieurs de modèle différent, ce message ne s’affichera pas si l’un des

appareils intérieurs présente cette fonction.

2. Nomenclature

Capteur de température intégré

Section de l’affichage

Pour cette explication, toutes les

parties de l’affichage sont mon-

trées allumées. Lors du fonction-

nement réel, seuls les éléments

correspondants seront allumés.

˚F˚C

ERROR CODE

AFTER

TIMER

TIME SUN MON TUE WED THU FRI SAT

OFF

AFTER

FILTER

FUNCTION

ONLY1Hr.

WEEKLY

SIMPLE

AUTO OFF

Indique l’opération en cours

Montre le mode de fonctionne-

ment, etc.

* les affichages peuvent être en

plusieurs langues.

Témoin “Commande centrale”

Indique que le fonctionnement de

la commande à distance a été

désactivée par une commande

maîtresse.

Témoin “Programmateur éteint”

Indique que le programmateur est

éteint.

Réglage de température

Indique la température souhaitée.

Jour de la semaine

Indique le jour de la semaine.

Affichage heure/programmateur

Indique l’heure actuelle (horloge de 12 heures ou horloge de 24

heures), à moins que la minuterie simple ou d'arrêt auto soit en service.

Si le programmateur simple ou arrêt auto est en activé, l’affichage

indique le temps restant.

Témoin “Capteur”

S’affiche lors de l’utilisation du capteur

de la télécommande.

Indicateur “Verrouillé”

Indique que les boutons de la com-

mande à distance ont été bloqués.

Témoin “Nettoyer le filtre”

S’allume quand il est temps de net-

toyer le filtre.

Témoins du programmateur

Ce témoin s’allume quand le program-

mateur correspondant est en fonction.

Témoin de montée/descente

d’air

Ce témoin indique dans quelle

direction souffle l’air sortant.

Témoin “une heure seulement”

Il s’affiche si le courant d’air est

réglé sur faible et descendant, lors

des modes FROID ou SEC. (L’opé-

ration varie en fonction du mo-

dèle.)

Le témoin s’éteint au bout d’une

heure, et à ce moment-là le flux

d’air change aussi.

Affichage de température

ambiante

Donne la température ambiante. La plage d’affi-

chage de la température de la pièce est comprise

entre 46 °F [8 °C]–102 °F [39 °C]. L’affichage

clignote si la température descend au-dessous de

46 °F [8 °C] ou monte au-dessus de 102 °F [39 °C].

Témoin de vitesse du ventilateur

Montre la vitesse sélectionnée pour le

ventilateur.

Témoin de ventilation

Apparaît quand l’unité fonctionne en

mode Ventilation.

Affichage du louvre

Montre l’action de la grille de transfert.

N’apparaît pas si la grille reste stationnaire.

(Témoin de marche)

Indique que l’appareil est en marche.

Section de commandes

Boutons de réglage de température

Baisser

Monter

Bouton de menu du programmateur

(Bouton Monitor/Set)

Bouton de mode

(bouton d’entrée)

Boutons de réglage horaire

Reculer

Avancer

Bouton marche/arrêt du pro-

grammateur

(Bouton de réglage de la date)

Ouvrir la

porte.

Bouton ON/OFF

Bouton de vitesse du ventilateur

Bouton du filtre

(Bouton )

Bouton de test de

fonctionnement

Bouton Check

(bouton d’effacement)

Bouton de ventilation mon-

tante/descendante

Bouton de louvre

(Bouton opération

)

pour la précédente

opération

Bouton de ventilation

(bouton opération

)

pour l’opération suivante

KB79M101H01_F.pm6 08.9.5, 5:25 PM19

2. Nomenclature

Remarque :

● Le jour et l’heure n’apparaîtront pas si l’horloge a été déconnectée dans la

sélection des fonctions.

● Au retour de l’alimentation, l’appareil intérieur ne fonctionnera pas pendant

trois minutes. Le fonctionnement décrit ci-dessus est normal.

● Si

1 1

1 ou

2 est spécifié comme réglage, l’horloge de 12 heures (AM/PM)

apparaît.

1Réglage CHANGE LANGUAGE = Anglais [Reportez-vous à la page 12]

2Réglage de l’affichage de la température =

°F [Reportez-vous à la page 12]

Si ces réglages ne sont pas effectués, l’horloge de 24 heures (heures des

chemins de fer/heure militaire) apparaîtra.

Seuls les écrans “Régler date/deure”, “Écrans de contrôle standard”, “Mo-

niteur du programmateur” et “Configuration du programmateur” sont con-

cernés par ces réglages.

1. Appuyez sur le bouton de réglage horaire A

ou pour appeler l’affichage 2.

2. Appuyez sur le bouton 9 Timer On/Off (Régler date) pour régler le jour.

* À chaque fois que vous appuyez, vous avancez le jour affiché en 3 : Dim →

Lun → … → Ven → Sam.

3. Appuyez sur le bouton de réglage correspondant A afin de régler l’heure.

* À chaque fois que vous maintenez le bouton appuyé, l’heure (en 4 ) augmen-

tera d’abord toutes les minutes, puis toutes les 10 minutes, puis toutes les heu-

res.

4. Après avoir effectué les réglages nécessaires des étapes 2 et 3, appuyez sur le

bouton 4 Filter

pour valider ces informations.

Remarque :

● Vos nouvelles informations des étapes 2 et 3 seront effacées si vous tapez le

bouton

2 Mode (Entrée) avant d’appuyer sur le bouton

4 Filter

5. Appuyez sur le bouton 2 Mode (Entrée) pour terminer la procédure de réglage.

Cela ramènera l’affichage sur l’écran de contrôle standard, où 1 vous indiquera le

nouveau jour et la nouvelle heure.

TIME SUN

4. Régler le jour de la semaine et l’heure

Le paramétrage de la langue d’affichage peut être modifié pour que le français de-

vienne la langue par défaut en sélectionnant la fonction appropriée sur la télécom-

mande. Voyez la section 8, paragraphe pour modifier la langue.

La langue de base est l’Anglais.

● Sélection des fonctions : Règle les fonctions et les plages disponibles

pour la télécommande (fonctions du program-

mateur, restrictions de fonctionnement, etc.)

● Régler date / heure : Règle le jour de la semaine et l’heure.

● Écrans de contrôle standards : Visualise et règle le fonctionnement du système

de conditionnement.

● Moniteur du programmateur : Affiche le programmateur en place (hebdoma-

daire, simple ou arrêt automatique)

● Configuration du programmateur : Règle le fonctionnement des programmateurs

(hebdomadaire, simple ou arrêt automatique)

Pour aller à A : Appuyer sur les boutons Mode et On/Off du programmateur durant

2 secondes.

Pour aller à B : Appuyez sur le bouton Menu du programmateur.

Pour aller à C : Appuyez sur le bouton Mode (Entrée).

Pour aller à D : Appuyez sur l’un ou l’autre des boutons de réglage horaire (

OFF ON

ADC

3. Configuration d’écran

Sélection des fonctions Règle date / heure

Filtres de contrôle standards

Moniteur du programmateur Configuration du programmateur

Affichage du jour de la

semaine et de l’heure

Réglage de l’heure

Réglage du jour de la semaine

31-1/2

11-13/16+29/32

23-5/8

5-29/32

2-23/32

19-11/16

■ Unité externe

■ A12, A18 (inch)

˚F˚F

TIMER

MON

OFF

WEEKLY

SUN MON TUE WED THU FRI SAT

WEEKLY

˚F˚F

˚F

TIME SUN

˚F

TIME SUN

PAR-21MAA

ON/OFF

FILTER

CHECK

OPERATION

CLEAR

TEST

TEMP.

BACK DAY

MONITOR/SET

CLOCK

ON/OFF

KB79M101H01_F.pm6 08.9.5, 6:18 PM20

La page charge ...

Mitsubishi PEA-A12 Manuel utilisateur

Marque: Mitsubishi

Modèle: PEA-A12

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Mitsubishi PEA-A12 User manual

Mitsubishi PEA-A12 Manuel utilisateur

Ce manuel convient également à

Mitsubishi PEA-A12 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents