Dura Vac VWMB508 0401 Manuel utilisateur

Marque: Dura Vac

Modèle: VWMB508 0401

Catégorie: Aspirateurs

Taper: Manuel utilisateur

Distributed By

Cleva North America, Inc.

601 Regent Park Court

Greenville, SC 29607

FOR YOUR SAFETY

Read and understand this manual before use.

Keep this manual for future reference.

Wall Mountable Wet/Dry Vacuum

Model No.

VWMB508 0401

Operator’s Manual

Wet/Dry Vacuums

Warranty ........................................................................................................................................

Safety Instructions and Warnings ..................................................................................................

Double Insulation Instructions .......................................................................................................

Extension Cords..............................................................................................................................

Package Contents..........................................................................................................................

General Assembly Instructions ......................................................................................................

Dry Vacuum Operation ..................................................................................................................

Liquid Vacuum Operation ..............................................................................................................

Blowing Operation .........................................................................................................................

Care and Maintenance ..................................................................................................................

Installing & Cleaning Cartridge Filter .............................................................................................

Installing & Cleaning Foam Sleeve Filter .......................................................................................

Resetting the Remote Control .......................................................................................................

Troubleshooting .............................................................................................................................

Exploded View ...............................................................................................................................

Parts List ........................................................................................................................................

SECTION

TABLE OF CONTENTS

WARRANTY

Thank you for purchasing this Dura Vac™ wet/dry vacuum cleaner.

Feel conﬁ dent that with Dura Vac™ you are obtaining a high quality product engineered for

optimal performance. This vacuum is capable of picking up liquids and dry materials.

FOR YOUR SAFETY: CAREFULLY READ AND UNDERSTAND ALL INSTRUCTIONS.

We take pride in producing a high quality, durable product. This Dura Vac™ product carries a

limited two (2) year warranty against defects in workmanship and materials from date of purchase

under normal household use. If product is to be used for commercial, industrial, or rental use, a 90

day limited warranty will apply. Warranty does not apply to defects due to direct or indirect abuse,

negligence, misuse, accidents, repairs, alterations, or lack of maintenance.

Please keep your receipt as proof of purchase. This warranty gives you speciﬁ c legal rights.

For product service call Customer Service at 1-866-384-8432

This device complies with RSS-210. Operation is subject to the following two conditions: (1)

this device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

SAFETY INSTRUCTIONS & WARNINGS

IMPORTANT SAFETY INSTRUCTIONS

SAVE THIS MANUAL

WARNING:

FOR FUTURE REFERENCE.

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY:

READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE USING THIS VACUUM

Read and understand this operator's manual and all labels on the Wet/Dry Vacuum cleaner before

operating. Safety is a combination of common sense, staying alert, and knowing how your vacuum

works. Use this Wet/Dry Vac only as described in this manual. To reduce the risk of personal injury

or damage to your Wet/Dry Vac, use only Dura Vac™ recommended accessories.

When using an electrical appliance, basic precautions should always be followed

including the following:

• Do not run vac unattended.

• Do not vacuum, or use this Wet/Dry Vac near ﬂ ammable liquids, gases, or explosive vapors like

gasoline or other fuels, lighter ﬂ uids, cleaners, oil-based paints, natural gas, hydrogen, or

explosive dusts like coal dust, magnesium dust, grain dust, or gun power. Sparks inside the

motor can ignite ﬂ ammable vapors or dust.

• Do not vacuum anything that is burning or smoking, such as cigarettes, matches, or hot ashes.

• Keep cord away from heated surfaces.

• Do not expose to rain. Store indoors.

• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

• Do not use with damaged cord, plug, or other parts.

• If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped

into water, return it to a service center.

• Do not pull or carry by cord, use cord as handle, close a door on cord, or pull cord around sharp

edges or corners.

• Do not run Wet/Dry Vac over cord.

• Do not handle plug or the Wet/Dry Vac with wet hands.

• To reduce the risk of health hazards from vapors or dusts, do not vacuum toxic materials.

• Do not use or store near hazardous materials.

• Do not use this Wet/Dry Vac with a torn ﬁ lter or without the ﬁ lter installed except when vacuuming

liquids as described in the operation section of this manual.

• Do not allow to be used as a toy. Close attention is necessary when used by or near children.

• To reduce the risk of injury from accidental starting, unplug power cord before changing or

cleaning ﬁ lter.

• Do not leave Wet/Dry Vac unattended when plugged in. Unplug from outlet when not in use and

before servicing.

• Turn off Wet/Dry Vac before unplugging.

• Do not put any object into ventilation openings. Do not vacuum with any ventilation openings

blocked; keep free of dust, lint, hair, or anything that may reduce air ﬂ ow.

• Keep hair, loose clothing, ﬁ ngers, and all parts of body away from openings and moving parts.

• To reduce the risk of falls, use extra care when cleaning on stairs.

• Unplug before connecting hose.

• Use only as described in this manual. Use only manufacturer’s recommended attachments.

• This appliance is provided with double insulation. Use only identical replacement parts.

See “DOUBLE INSULATION INSTRUCTIONS”.

When using as blower:

• Direct air discharge only at work area.

• Do not use Wet/Dry Vac as a sprayer.

• Do not direct air at bystanders.

• Keep children away when blowing.

• Use safety goggles.

Household Type

DOUBLE INSULATION INSTRUCTIONS

EXTENSION CORDS

This Wet/Dry Vac is double-insulated, eliminating the need for a separate grounding system. Use

only identical replacements parts. Read the instructions for Servicing Double-Insulated Wet/Dry

Vacs before servicing. Use this Wet/Dry Vac as described in this manual. Observe the following

warnings that appear on the motor housing of your Wet/Dry Vac.

When using an extension cord with your Wet/Dry Vac refer to the following table to determine

the required A.W.G. wire size. Before using the vacuum cleaner, make sure the power cord and

extension cord are in good working condition. Make repairs or replacements before using the

vacuum cleaner. Only use extension cords that are rated for outdoor use.

• To reduce the risk of electric shock-unplug before cleaning or servicing.

• DO NOT use without ﬁ lters in place.

CAUTION: TO REDUCE THE RISK OF INJURY FROM MOVING PARTS- UNPLUG BEFORE

SERVICING.

DOUBLE INSULATED - GROUNDING NOT REQUIRED - WHEN SERVICING USE

ONLY IDENTICAL REPLACEMENT PARTS.

TO REDUCE THE RISK OF ELECTRIC SHOCK-DO NOT EXPOSE TO RAIN.

STORE INDOORS.

WARNING:

WARNING: SERVICING OF DOUBLE-INSULATED WET/DRY VACUUM

WITH A DOUBLE-INSULATED WET/DRY VACUUM, TWO SYSTEMS OF INSULATION ARE

PROVIDED INSTEAD OF GROUNDING. NO GROUNDING MEANS IS PROVIDED ON A

DOUBLE-INSULATED APPLIANCE, NOR SHOULD A MEANS FOR GROUNDING BE ADDED.

SERVICING A DOUBLE INSULATED WET/DRY VACUUM REQUIRES EXTREME CARE AND

KNOWLEDGE OF THE SYSTEM, AND SHOULD BE DONE ONLY BY QUALIFIED SERVICE

PERSONNEL. REPLACEMENT PARTS FOR A DOUBLE-INSULATED WET/DRY VACUUM

MUST BE IDENTICAL TO THE PARTS THEY REPLACE. YOUR DOUBLE-INSULATED

WET/DRY VAC IS MARKED WITH THE WORDS ‘DOUBLE INSULATED’ AND THE SYMBOL

(SQUARE WITHIN A SQUARE) MAY ALSO BE MARKED ON THE APPLIANCE.

Length of Extension Cord

A.W.G. Wire Size

Not recommended

25 Feet

7.5 Meters 50 Feet

15.25 Meters 100 Feet

30.5 Meters 150 Feet

45.7 Meters

110V-120V

Amps

0-6

7-10

11-12

13-16

PACKAGE CONTENTS

Remove entire contents of carton. Check each

item against the carton contents list.

Carton contents lists

Key Description ..………………….….... Qty.

A Hose Storage Rack ………….........

B Steel Mounting Rod ………...….....

C Mounting Rack ………..…...….......

D Wire Accessory Rack …….…….....

E Vac Assembly ….…........................

F Standard Hose ………….……........

G Flex Hose ……………....................

H Extension Wands ……………........

I Car Nozzle …….............................

J Floor / Squeegee Nozzle ……........

K Crevice Tool ……………................

L Round Brush………………….….....

M Utility Nozzle.……………….............

N Remote Control Handle .….............

O Cartridge Filter ……………….........

P Foam Filter ………….....................

Q Screws …………….........................

R Operator ’s Manual …………….......

NOTE: The hose and accessories for this

vacuum are 1-7/8" (47.6mm). diameter.

GENERAL ASSEMBLY INSTRUCTIONS

TO REDUCE THE RISK OF ELECTRIC SHOCK-DO NOT EXPOSE TO RAIN.

MAKE SURE PLUG IS DISCONNECTED BEFORE ASSEMBLING THE WET/DRY VAC.

WARNING:

UNPACKING YOUR WET/DRY VACUUM & GENERAL ASSEMBLY

1. Verify that the power cord is disconnected from the outlet. (ﬁ g. 1)

2. Undo the latches. (ﬁ g. 2)

3. Lift the power head off of the container. (ﬁ g. 3)

4. Remove the contents from inside the container. Make sure you have all contents as listed on

page 6. (ﬁ g. 4)

5. Insert the steel rod into the hose holding rack, and snap into place. Make sure the buttons on

the rod are directed as illustrated. (ﬁ g. 5a & ﬁ g. 5b)

6. Locate the two openings on the bottom of the mounting rack and insert the wire accessory

storage into the mounting rack until they lock in place. Make sure the wire accessory storage is

directed towards the front side of the mounting rack. (ﬁ g. 6)

7. Insert the steel rod with hose holding rack into the two holes located on the top of the mounting

rack. Ensure the Dura Vac logo is facing forward. (ﬁ g. 7)

MOUNTING RACK AND STORAGE ASSEMBLY

IMPORTANT!

• Do not mount the rack over 5 feet from the ﬂ oor.

• Do not screw the rack to drywall only. Secure the screws to a stud.

• Do not hang from or sit on the mounting rack.

• Do not exceed 40 pounds (18 kilograms) of maximum weight.

8. Locate a wall stud that is not more than 18 feet (5.5 meters) away from an electrical outlet.

Align the three screw holes on the mounting rack so that they are over the stud. Make sure the

rack is level and mark the hole locations. Make a 1/8" (3mm) diameter pilot hole in each marked

location. Secure the mounting rack to the wall stud with the three screws provided. (ﬁ g. 8)

MOUNTING THE VACUUM ON TO THE RACK

1. Your vacuum comes ready for dry vacuum cleaning. If the cartridge ﬁ lter is not installed refer

to page 13 for ﬁ lter installation. (ﬁ g. 9 & ﬁ g. 10)

2. Place the power head on the container, and secure into place using the 2 side latches.

(ﬁ g. 11 & ﬁ g.12)

3. Mount the vacuum onto the mounting rack by aligning the vac hanging hook on the rear with

slot on the mounting rack and slide downward until it locks. (ﬁ g. 13)

4. Wind the excess power cord around the cord wrap hooks located on the side of the vacuum.

(ﬁ g. 14)

5. Insert the locking end of the hose into the vacuum port and lock in to place. (ﬁ g. 15)

6. Secure a desired accessory, such as the suction control handle, onto the end of the hose.

(ﬁ g. 16)

POLARIZED PLUG

To reduce the risk of electrical shock, this appliance has a polarized plug (one blade is wider than

the other). This plug will ﬁ t in a polarized outlet only one way. If the plug does not ﬁ t fully in the

outlet, reverse the plug. If it still does not ﬁ t, contact a qualiﬁ ed electrician to install the proper

outlet. Do not change the plug in any way. Double insulation eliminates the need for the three

wire grounded power cord and grounded power supply system.

DISMOUNTING THE VACUUM FROM THE RACK

1 2

1. Disconnect the power cord from the electrical outlet. (ﬁ g. 1)

2. Lift the vacuum up and out of the rack by the handle. (ﬁ g. 2)

DRY-VACUUM OPERATION

DRY VACUUMING

WARNING: BE SURE TO READ, UNDERSTAND, AND APPLY INFORMATION,

ENTITLED ‘SAFETY INSTRUCTIONS & WARNINGS’. DO NOT VACUUM IN AREAS WITH

FLAMMABLE GASES, VAPORS, OR EXPLOSIVE DUSTS IN THE AIR. FLAMMABLE

GASES OR VAPORS INCLUDE BUT ARE NOT LIMITED TO: LIGHTER FLUID, SOLVENT

TYPE CLEANERS, OIL-BASE PAINTS, GASOLINE, ALCOHOL OR AEROSOL SPRAYS.

EXPLOSIVE DUSTS INCLUDE BUT ARE NOT LIMITED TO: COAL, MAGNESIUM, GRAIN

OR GUN POWDER. TO REDUCE THE RISK OF HEALTH HAZARDS FROM VAPORS OR

DUST, DO NOT VACUUM TOXIC MATERIALS.

WARNING: DO NOT PLUG IN POWER CORD TO POWER OUTLET. MAKE SURE PLUG

IS DISCONNECTED BEFORE CHANGING OR CLEANING FILTERS.

NOTICE

Do not vacuum drywall dust or ﬁ replace soot or ash with standard Wet/Dry ﬁ lter. This is a very ﬁ ne

dust which will not be captured by the ﬁ lter and may cause damage to motor. When vacuuming

ﬁ ne dust use a ﬁ ne dust ﬁ lter (sold separately).

1. Verify that the power cord is disconnected from the outlet. (ﬁ g. 1)

2. In order to prepare your vacuum for dry vacuuming, verify that the cartridge ﬁ lter is securely

mounted. With the power head removed and in the upside down position, make sure the ﬁ lter is

pushed in until it stops against the power head. (ﬁ g. 2) Your Wet/Dry Vac comes with the

cartridge ﬁ lter pre-installed, if not see page 13 for installation instructions.

3. Place ﬁ lter retainer on top of cartridge ﬁ lter and tighten down by turning the retainer handle

clockwise. (ﬁ g. 3)

4. Place the power head back on the container, aligning the top section with the latches, and lock

into place. (ﬁ g. 4)

LIQUID VACUUM OPERATION

LIQUID VACUUMING

WARNING: BE SURE TO READ, UNDERSTAND, AND APPLY INFORMATION,

ENTITLED ‘SAFETY INSTRUCTIONS & WARNINGS’. DO NOT VACUUM IN AREAS WITH

FLAMMABLE GASES, VAPORS, OR EXPLOSIVE DUSTS IN THE AIR. FLAMMABLE

GASES OR VAPORS INCLUDE BUT ARE NOT LIMITED TO: LIGHTER FLUID, SOLVENT

TYPE CLEANERS, OIL-BASE PAINTS, GASOLINE, ALCOHOL, OR AEROSOL SPRAYS.

EXPLOSIVE DUSTS INCLUDE BUT ARE NOT LIMITED TO: COAL, MAGNESIUM, GRAIN,

OR GUN POWDER. TO REDUCE THE RISK OF HEALTH HAZARDS FROM VAPORS OR

DUST, DO NOT VACUUM TOXIC MATERIALS.

WARNING: DO NOT PLUG IN POWER CORD TO POWER OUTLET.

MAKE SURE PLUG IS DISCONNECTED BEFORE CHANGING OR CLEANING FILTERS.

OPERATING INSTRUCTIONS: DRY VACUUMING

5. Insert the locking end of the hose into the vacuum port and lock in place. Push the required

attachment onto the free end of the hose or extension. (ﬁ g. 5)

6. Verify that the switch is in the 'O' (OFF) position before plugging the power cord into the outlet

(ﬁ g. 6). Hang the vacuum onto the rack or use off the rack.

7. Turn the motor on by ﬂ ipping the switch to the ‘I’ ON position. (ﬁ g. 7) For remote control use,

set the power switch to remote control position “ ” and turn the vacuum on by pressing the

‘I’ ON button on the remote control. (ﬁ g. 8 & ﬁ g. 9)

8. Once you have completed vacuuming, ﬂ ip the switch to the ‘O’ OFF position or press the ‘O’

OFF button on the remote control for at least one second.

O = OFF I = ON = Remote Control

DO NOT USE THE CARTRIDGE FILTER FOR LIQUID VACUUMING.

IMPORTANT! When vacuuming large quantities of liquids, we recommend that you remove the

vacuum from the mounting rack and put it on the ﬂ oor. The vacuum can be heavy when full of

liquids and may be difﬁ cult to remove from the rack.

DO NOT USE THE CARTRIDGE FILTER FOR LIQUID VACUUMING.

1. Verify that the power cord is disconnected from the outlet (ﬁ g. 1). Verify that the container is

clean and free of dust and dirt.

2. Remove the cartridge ﬁ lter, then carefully install the foam sleeve ﬁ lter over the ﬁ lter cage (ﬁ g. 2)

and place the power head back on the container. See ﬁ lter installation instructions on page 13.

3. Fit the desired nozzle to the vacuum hose. (ﬁ g. 3)

4. Verify that the switch is in the ‘O’ OFF position before plugging the power cord into the outlet.

(ﬁ g. 4 & ﬁ g. 5)

5. Turn the motor on by ﬂ ipping the switch on the power head to the ‘I’ ON position or ﬂ ip the

switch to the remote control position and use the ‘I’ ON button on the remote control.

6. After wet vacuuming, turn the machine off and remove plug from power supply. Empty the

container (ﬁ g. 6), clean and dry the inside and outside of the container, and remove the foam

ﬁ lter and allow to air dry before storage.

IMPORTANT! When vacuuming large quantities of liquids, do not immerse the nozzle completely

in the liquid; leave a gap at the tip of the nozzle opening to allow air inﬂ ow. The machine is ﬁ tted

with a ﬂ oat valve that stops the suction action when the container reaches its maximum capacity.

You will notice an increase in motor speed. When this happens, turn off the machine, disconnect

from power supply, and empty the liquid into a suitable receptacle or drain. To continue vacuuming,

reﬁ t the power head to the container. After wet vacuuming, turn the machine off and remove plug

from power supply. To prevent the risk of possible mildew, empty the container, clean and dry the

inside and outside of the container, and remove the foam ﬁ lter and allow to air dry before storage.

REMEMBER! The foam ﬁ lter must be removed after wet vacuuming, and a cartridge ﬁ lter must be

installed before dry vacuuming again.

DO NOT SUBMERGE THE REMOTE CONTROL IN LIQUIDS.

BLOWING OPERATION

This Wet/Dry Vac has blowing capabilities. To use the blower feature follow the instructions listed.

1. Verify that the switch is in the '0' (OFF) position. (ﬁ g. 1)

2. Make sure the container is empty before using as a blower.

3. Lift the button on the blower ﬁ lter door to the unlocked position and ﬂ ip the blower ﬁ lter door

open. (ﬁ g. 2)

4. Remove hose from the vacuum port and insert the locking end of the hose into the blowing port

on the power head and lock into position. (ﬁ g. 3)

5. Fit the desired extension wand and/or nozzle to the free end of the vacuum hose. (ﬁ g. 4)

6. Before turning ON the vac, ﬁ rmly hold loose end of the hose. Turn the motor on by ﬂ ipping the

switch to the ‘I’ ON position (ﬁ g. 5) or set the switch to the remote control setting and use the

remote control.

WARNING: ALWAYS WEAR SAFETY GOGGLES COMPLYING WITH CSAZ94.3

BEFORE USING BLOWER.

WARNING: WEAR A DUST MASK IF BLOWING CREATES DUST THAT MIGHT

BE INHALED.

CAUTION: KEEP BYSTANDERS CLEAR FROM BLOWING DEBRIS.

WARNING: ALWAYS DISCONNECT THE PLUG FROM THE POWER OUTLET BEFORE

REMOVING THE POWER HEAD FROM THE CONTAINER.

1. Verify that the power cord is disconnected from the outlet. (ﬁ g. 1)

2. Disconnect the hose from the vacuum. (ﬁ g. 2)

3. Remove the vacuum from the mounting rack.

4. Undo the latches and remove the power head from the container. (ﬁ g. 3)

5. Clear all dirt or debris from the container and hose. (ﬁ g. 4)

6. Check the hose, attachments, and power cord to verify that they have not been damaged.

IMPORTANT! Clean or change the cartridge ﬁ lter regularly for best performance. ALWAYS USE

CARTRIDGE FILTER FOR DRY VACUUMING. If the machine is used without the cartridge ﬁ lter,

the motor will burn out and the warranty will be voided. Always keep spare cartridge ﬁ lters on

hand.

NOTICE! The ﬁ lters included are made of high quality materials designed to stop small dust

particles. The cartridge ﬁ lter should be used for dry pick-up only. A dry cartridge ﬁ lter is necessary

to pick up dust. If the cartridge ﬁ lter is wet, it will clog quickly and be difﬁ cult to clean. Handle the

ﬁ lter carefully when removing it for cleaning or replacing. Check the ﬁ lters for tears or small holes.

A small hole can let dust pass through and out of the cleaner. Do not use a ﬁ lter with holes or tears

in it; replace it immediately.

CARE AND MAINTENANCE

INSTALLING AND CLEANING

THE CARTRIDGE FILTER

INSTALLING AND CLEANING

THE FOAM SLEEVE FILTER

Installing Cartridge Filter

1. Verify that the power cord is disconnected from the outlet. (ﬁg. 1)

2. Remove power head and place in upside down position.

3. Install the cartridge ﬁ lter over the ﬁ lter cage with the ﬂ at end of the ﬁ lter towards the vacuum

power head. Carefully push ﬁ lter in until it stops against the power head. (ﬁg. 2 & 3)

4. Place ﬁ lter retainer on top of cartridge ﬁ lter over the raised lip and tighten down by turning

retainer clockwise, taking care not to over tighten. (ﬁ g. 4 & 5)

Removing and Cleaning Cartridge Filter

1. Unlock and remove the ﬁ lter retainer by turning retainer handle counterclockwise.

2. Carefully remove the cartridge ﬁ lter by sliding it off of the ﬁ lter cage. (ﬁg. 6)

3. Clean the cartridge ﬁ lter by gently tapping or brushing dirt off. Cleaning should not be done

indoors in living areas. For optimal performance a new ﬁ lter is recommended.

4. Install cleaned or new ﬁ lter as instructed above in steps 2 and 3 of Installing Cartridge Filter.

5. Wet ﬁ lters should be removed and allowed to dry for 24 hours before installing onto the ﬁ lter

cage.

Installing Foam Sleeve Filter

1. Verify that the power cord is disconnected from the outlet. (ﬁ g. 1)

2. Remove power head and place in upside down position. Follow instructions to remove cartridge

ﬁ lter in the section above.

3. Carefully slide foam sleeve ﬁ lter down over the ﬁ lter cage making sure the whole cage is

covered. (ﬁ g. 2 & ﬁ g. 3)

4. Replace the power head onto the container.

Cleaning Foam Sleeve Filter

1. With the removed power head in the upside down position, carefully remove foam sleeve ﬁ lter.

(ﬁ g. 4)

2. Use a mild soap and water solution to wash foam sleeve ﬁ lter and rinse with clean water. (ﬁg. 5)

3. Allow ﬁ lter to air dry before installing and using again.

RESETTING THE REMOTE CONTROL

1. Have the remote control accessible. Set the power switch on the vacuum to the remote control

position “ ”. (ﬁ g. 1)

2. Press the RESET button on the side of the power head with pointed object such as paper clip or

a pen tip until the indicator lights up. (ﬁ g. 2)

3. Release the RESET button once the red indicator light lights up and immediately press and hold

the “ON” button on the remote control handle until the vacuum powers on. (ﬁ g. 3)

4. If the “ON” button is not pressed and held within a 15 second window, the reset will not be

successful. Repeat steps 2-3 to reset the remote control.

Changing The Battery – Replace Only With A 23AE 12V Alkaline Battery

1. Using a Phillips screwdriver, remove the screws on the remote control. (ﬁ g. 1)

2. Slide back the remote cover so that the white triangle on the remote cover points to the unlock

symbol “ ” . (ﬁ g. 2 & 3)

3. Remove the remote cover from the handle. (ﬁ g. 4)

4. Lift the foam cover to expose the battery and remove the old battery. (ﬁ g. 5)

5. Insert the new battery with the terminals in the direction shown and make sure to replace the

foam cover. (ﬁ g. 6 & 7)

6. Replace the remote control by aligning the white triangle on the side cover to the unlock symbol

“ ” on the handle. (ﬁ g. 8)

7. Slide the remote cover so that the white triangle is over the locked symbol “ ” . (ﬁ g. 9 & 10)

8. Secure the cover with the screws. Do not over tighten. (ﬁ g. 11)

TROUBLESHOOTING

WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK-UNPLUG BEFORE

TROUBLESHOOTING.

Symptom Possible Causes Corrective Action

Vacuum will not operate

1) No power supply. 1) Check power supply – cord,

breakers, fuses.

2) Faulty power cord. 2) Unplug and check the

power cord. If damaged,

have it repaired by a

professional.

3) Container full. 3) Empty container.

4) Switch in the wrong

position 4) Press the ON ‘I’ button on

the power head.

1) The cartridge ﬁ lter is

missing or damaged. 1) Attach or replace cartridge

ﬁ lter.

2) Vacuum has been used to

collect ﬁ ne dust, such as

drywall dust, ﬁ replace soot,

or ash, without a ﬁ ne dust

ﬁ lter equipped.

2) Remove the standard

cartridge ﬁ lter and install

the appropriate ﬁ ne dust

cartridge ﬁ lter.

1) There is a blockage in the

nozzle, hose, or the

container inlet.

The cartridge ﬁ lter is

clogged by ﬁ ne dust.

1) Check nozzle, hose and

container inlets for blockage.

Take off the ﬁ lter and clean

it.

Or install new cartridge ﬁ lter.

1) Remote is not paired with

the vac. 1) Reset the remote using the

instructions on page 14.

2) Battery is dead. 2) Replace the battery.

Dust comes out from

motor cover.

Reduced efﬁ ciency and

motor/speed vibration.

Remote will not operate

Changes or modiﬁ cations not expressly approved by the party responsible for compliance could

void the user's authority to operate the equipment.

EXPLODED VIEW

PARTS LIST

Part Description Part# Qty

Included

with Vac

A Power Head Assembly VW50P1.10.00 1

B Blower Door VW50P1.10.05 1

C Vacuum Port Assembly TVQTXK.06.01 1

D Latch Assembly TVQTDK.14.00 1

E Container VW50P1.20.01 1

F Foot VW50P1.20.02 1

G Hose Storage Rack VW02P1.20.02 1

H Steel Mounting Rod VW50P1.30.02 1

I Mounting Rack VW50P1.30.03 1

J Hardware Pack VW01P1.30.03 2

K Accessory Storage Rack VW01P1.30.04 1

L Standard Hose V78SH 1

M Flex Hose V78FH 1

N Extension Wands FV5901.01.01 2

O Car Nozzle FV5771.03.01 1

P Floor / Squeegee Nozzle FV5708.00.00 1

Q Crevice Tool FV5771.01.02 1

R Utility Nozzle FV5772.01.01 1

S Round Brush FV5773.01.00 1

T Remote Control Handle FV5331.01.01 1

U Cartridge Filter CVWCFA 1

V Foam Filter FV9543.06.20 1

W Screw Pack (3 count) BOA2SP.48.42 1

X Operator's Manual 1

www.duravac.ca

Cleva North America, Inc.

601 Regent Park Court

Greenville, SC 29607

POUR VOTRE SÉCURITÉ

Veuillez lire attentivement et comprendre ce manuel d’utilisation

avant d’utiliser l’aspirateur

Conservez ce manuel pour référence ultérieure

Aspirateur de Matières Sèches et Liquides à Fixation Murale

Model No.

VWMB508 0401

Manuel d’utilisation

Aspirateurs de

détritus

secs et de liquides

Garantie ........................................................................................................................................

Instructions de sécurité et avertissements .....................................................................................

Instructions sur la double isolation .................................................................................................

Cordon prolongateur.......................................................................................................................

Déballage et vériﬁ cation du contenu de la boîte d’emballage........................................................

Instructions générales d’assemblage ............................................................................................

Utilisation de l’appareil pour aspirer des détritus secs...................................................................

Utilisation de l’appareil pour aspirer des liquides............................................................................

Utilisation de la soufﬂ ante...............................................................................................................

Entretien ........................................................................................................................................

Installation et nettoyage du ﬁ ltre à cartouche.................................................................................

Installation et nettoyage du ﬁ ltre à manchon en mousse...............................................................

Réinitialisation de la télécommande...............................................................................................

Dépannage ....................................................................................................................................

Schéma éclaté ...............................................................................................................................

Liste des pièces..............................................................................................................................

SECTION

TABLE DES MATIÈRES

GARANTIE

Nous vous remercions d’avoir acheté cet aspirateur de détritus secs et de liquides

Dura Vac™. Soyez assuré que ce produit de haute qualité vous procurera un

rendement optimal. Cet appareil est conçu pour aspirer les liquides et les détritus secs.

POUR PLUS DE SÉCURITÉ : LIRE ATTENTIVEMENT ET VEILLER À BIEN

COMPRENDRE TOUTES LES INSTRUCTIONS

Dura Vac™ est ﬁ ère de fabriquer des produits durables de qualité supérieure. Ce produit Dura

Vac™ est accompagné d’une garantie limitée de deux (2) ans à compter de la date d’achat contre

tout vice de fabrication ou de matériel pour un usage domestique normal. Si le produit est utilisé

à des ﬁ ns commerciales, industrielles ou de location, la garantie s’appliquera pour une période

limitée de 90 jours. Cette garantie ne couvre pas les défauts de fonctionnement liés directement

ou indirectement à une utilisation abusive, à de la négligence, à des accidents, à des réparations,

à des modiﬁ cations ou à une carence d’entretien. Veuillez conserver le reçu comme preuve d’achat.

La présente garantie donne au consommateur des droits spéciﬁ ques, et celui-ci peut bénéﬁ cier

d’autres droits, qui varient selon les états ou les provinces. Pour toute question relative à l’entretien

du produit, veuillez communiquer avec le service à la clientèle au numéro 866 384-8432.

Les modiﬁ cations non autorisées expressément par la partie responsable de la conformité

peuvent annuler le droit de se servir de l’appareil.

Cet appareil est conforme à l’alinéa 15 des règlements de RSS-210. Son utilisation est

soumise aux deux conditions suivantes : (1) cet appareil ne doit pas provoquer de

brouillage préjudiciable et (2) il doit accepter tout interférence reçue, y compris les

interférences pouvant provoquer un fonctionnement indésirable.

INSTRUCTIONS DE SÉCURITÉ ET AVERTISSEMENTS

RÈGLES IMPORTANTES DE SÉCURITÉ

CONSERVER CE MANUEL

AVERTISSEMENT :

AFIN DE MINIMISER LE RISQUE D’INCENDIE,

DE DÉCHARGE ÉLECTRIQUE OU DE BLESSURE :

POUR RÉFÉRENCE ULTÉRIEURE.

LIRE ATTENTIVEMENT ET COMPRENDRE TOUTES LES INSTRUCTIONS AVANT

D’UTILISER CET APPAREIL

Lire attentivement et comprendre ce manuel d’utilisation ainsi que tous les autocollants apposés

sur l’aspirateur de détritus secs et de liquides avant de l’utiliser. Le bon jugement, l’attention et

une bonne connaissance du fonctionnement de l’appareil sont des gages de sécurité. Utiliser

uniquement l’aspirateur tel que décrit dans le présent manuel. Afin de minimiser le risque de

lésions corporelles et de dommages matériels, utiliser uniquement des accessoires recommandés

par Dura Vac™.

Lors de l’utilisation d’un appareil électrique, toujours suivre les consignes de

base, notamment :

• Ne pas laisser l’appareil en marche sans surveillance.

• Ne pas utiliser l’appareil en présence de liquides ou de gaz inﬂ ammables, de vapeurs explosives

notamment l’essence ou autres carburants, l’essence à briquet, les produits détergents, la peinture

à l’huile, le gaz naturel et l’hydrogène, ou de poussière explosive comme la poussière de charbon,

de magnésium ou de grain ou la poudre noire. Le moteur de l’appareil peut produire des étincelles

et enﬂ ammer des vapeurs ou des poussières inﬂ ammables.

• Ne pas aspirer d’éléments qui brûlent ou qui fument comme des cigarettes, des allumettes ou des

cendres chaudes.

• Tenir le cordon d’alimentation éloigné des surfaces brûlantes.

• Ne pas exposer l’appareil à la pluie. Entreposer l’appareil à l’intérieur.

• Ne pas débrancher l’appareil en tirant sur le cordon. Tirer plutôt sur la ﬁ che.

• Ne pas utiliser l’appareil si le cordon, la ﬁ che ou toute autre pièce sont endommagés.

• Si l’appareil ne fonctionne pas correctement, s’il a été échappé, s’il est endommagé, s’il a été

laissé à l’extérieur ou s’il est tombé dans l’eau, le retourner à un centre de réparations.

• Ne pas tirer l’appareil ou le transporter par le cordon d’alimentation, ne pas utiliser ce dernier

comme poignée ou le faire longer des arêtes ou des coins tranchants.

• Ne pas faire rouler l’appareil par-dessus le cordon.

• Ne pas manipuler l’aspirateur avec les mains mouillées.

• Pour réduire les risques pour la santé attribuables aux vapeurs ou à la poussière, ne pas aspirer

de substances toxiques.

• Ne pas utiliser ou entreposer l’appareil près de matières dangereuses.

• Ne pas utiliser l’appareil si le ﬁ ltre est déchiré ou sans le ﬁ ltre, sauf si l’appareil est utilisé aﬁ n

d’aspirer des ﬂ uides, tel que décrit dans la section Fonctionnement du présent manuel.

• S’assurer que l’appareil n’est pas utilisé comme un jouet. Il importe d’être vigilant si l’appareil est

utilisé à proximité des enfants ou par ceux-ci.

• Aﬁ n de minimiser les risques associés à un démarrage accidentel, s’assurer de débrancher le

cordon d’alimentation avant de procéder au changement ou au nettoyage du ﬁ ltre.

• Ne jamais laisser l’appareil sans surveillance lorsque celui-ci est branché. Débrancher l’appareil

lorsqu’il n’est pas utilisé et avant de procéder à son entretien.

• Mettre l’appareil à l’arrêt avant de le débrancher.

• Ne rien introduire dans les ouvertures de ventilation. Ne pas utiliser l’appareil si une ou plusieurs

ouvertures sont bloquées; s’assurer que les ouvertures ne sont pas obstruées par de la poussière,

des peluches, des cheveux ou tout autre élément pouvant réduire la circulation d’air.

• Garder les cheveux, les vêtements amples, les doigts ainsi que toutes les parties du corps à l’écart

des ouvertures et des pièces en mouvement.

Type Ménager

La page charge ...

Dura Vac VWMB508 0401 Manuel utilisateur

Marque: Dura Vac

Modèle: VWMB508 0401

Catégorie: Aspirateurs

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Dura Vac VWMB508 0401 User manual

Dura Vac VWMB508 0401 Manuel utilisateur

Dura Vac VWMB508 0401 Manuel utilisateur

dans d''autres langues

Autres documents