Dremel 8260 Manuel utilisateur

Catégorie
Outils électroportatifs
Taper
Manuel utilisateur
1-800-4-DREMEL (1-800-437-3635) www.dremel.com
Operating/Safety Instructions
Consignes d’utilisation/de sécurité
Instrucciones de funcionamiento y seguridad
IMPORTANT
Read Before Using IMPORTANT
Lire avant usage IMPORTANTE
Leer antes de usar
For English Version
See page 2 Version française
Voir page 24 Versión en español
Ver la página 47
Call Toll Free for Consumer Information and Service Locations
Pour obtenir des informations et les adresses de nos centres de service aps-vente, appelez ce nuro gratuit
Llame gratis para obtener información para el consumidor y ubicaciones de servicio
8260
2
1. Work area safety
a. Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b. Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power
tools create sparks which may ignite the
dust or fumes.
c. Keep children and bystanders away
while operating a power tool.
Distractions can cause you to lose
control.
2. Electrical safety
a. Power tool plugs must match the outlet.
Never modify the plug in any way. Do
not use any adapter plugs with earthed
(grounded) power tools. Unmodified
plugs and matching outlets will reduce
risk of electric shock.
b. Avoid body contact with earthed or
grounded surfaces such as pipes,
radiators, ranges and refrigerators.
There is an increased risk of electric
shock if your body is earthed or
grounded.
c. Do not expose power tools to rain or
wet conditions. Water entering a power
tool will increase the risk of electric
shock.
d. Do not abuse the cord. Never use the
cord for carrying, pulling or unplugging
the power tool. Keep cord away from
heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the
risk of electric shock.
e. When operating a power tool outdoors,
use an extension cord suitable for
outdoor use. Use of a cord suitable for
outdoor use reduces the risk of electric
shock.
f. If operating the power tool in damp
locations is unavoidable, use a Ground
Fault Circuit Interrupter (GFCI)
protected supply. Use of an GFCI
reduces the risk of electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and
use common sense when operating a
power tool. Do not use a power tool
while you are tired or under the
influence of drugs, alcohol or
medication. A moment of inattention
while operating power tools may result in
serious personal injury.
b. Use personal protective equipment.
Read all safety warnings and all instructions. Failure to follow the
warnings and instructions may result in electric shock, fire and/or serious
injury.
SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE
The term “power tool” in the warnings refers to your mains-operated (corded) power tool
or battery-operated (cordless) power tool.
General Power Tool Safety Warnings
Safety Symbols
The definitions below describe the level of severity for each signal word. Please read the
manual and pay attention to these symbols.
This is the safety alert symbol. It is used to alert you to potential
personal injury hazards. Obey all safety messages that follow this
symbol to avoid possible injury or death.
DANGER indicates a hazardous situation which, if not avoided, will
result in death or serious injury.
WARNING indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
CAUTION indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
3
Always wear eye protection. Protective
equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing
protection used for appropriate
conditions will reduce personal injuries.
c. Prevent unintentional starting. Ensure
the switch is in the off-position before
connecting to power source and / or
battery pack, picking up or carrying the
tool. Carrying power tools with your
finger on the switch or energizing power
tools that have the switch on invites
accidents.
d. Remove any adjusting key or wrench
before turning the power tool on. A
wrench or a key left attached to a rotating
part of the power tool may result in
personal injury.
e. Do not overreach. Keep proper footing
and balance at all times. This enables
better control of the power tool in
unexpected situations.
f. Dress properly. Do not wear loose
clothing or jewelry. Keep your hair,
clothing and gloves away from moving
parts. Loose clothes, jewelry or long hair
can be caught in moving parts.
g. If devices are provided for the
connection of dust extraction and
collection facilities, ensure these are
connected and properly used. Use of
dust collection can reduce dust-related
hazards.
4. Power tool use and care
a. Do not force the power tool. Use the
correct power tool for your application.
The correct power tool will do the job
better and safer at the rate for which it
was designed.
b. Do not use the power tool if the switch
does not turn it on and off. Any power
tool that cannot be controlled with the
switch is dangerous and must be
repaired.
c. Disconnect the plug from the power
source and/or the battery pack from the
power tool before making any
adjustments, changing accessories, or
storing power tools. Such preventive
safety measures reduce the risk of
starting the power tool accidentally.
d. Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for
misalignment or binding of moving parts,
breakage of parts and any other
condition that may affect the power
tool’s operation. If damaged, have the
power tool repaired before use. Many
accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean.
Properly maintained cutting tools with
sharp cutting edges are less likely to bind
and are easier to control.
g. Use the power tool, accessories and tool
bits etc. in accordance with these
instructions, taking into account the
working conditions and the work to be
performed. Use of the power tool for
operations different from those intended
could result in a hazardous situation.
5. Battery tool use and care
a. Recharge only with the charger specified
by the manufacturer. A charger that is
suitable for one type of battery pack may
create a risk of fire when used with
another battery pack.
b. Use power tools only with specifically
designated battery packs. Use of any
other battery packs may create a risk of
injury and fire.
c. When battery pack is not in use, keep it
away from other metal objects like
paper clips, coins, keys, nails, screws, or
other small metal objects that can make
a connection from one terminal to
another. Shorting the battery terminals
together may cause burns or a fire.
d. Under abusive conditions, liquid may be
ejected from the battery, avoid contact.
If contact accidentally occurs, flush with
water. If liquid contacts eyes,
additionally seek medical help. Liquid
ejected from the battery may cause
irritation or burns.
6. Service
a. Have your power tool serviced by a
qualified repair person using only
identical replacement parts. This will
ensure that the safety of the power tool is
maintained.
General Power Tool Safety Warnings
4
Safety warnings common for
grinding, sanding, wire
brushing, polishing, carving
or abrasive cutting-off
operations:
a. This power tool is intended to function
as a grinder, sander, wire brush,
polisher, carving or cut-off tool. Read all
safety warnings, instructions,
illustrations and specifications provided
with this power tool. Failure to follow all
instructions listed below may result in
electric shock, fire and/or serious injury.
b. Do not use accessories which are not
specifically designed and recommended
by the tool manufacturer. Just because
the accessory can be attached to your
power tool, it does not assure safe
operation.
c. The rated speed of the accessories must
be at least equal to the operating speed
setting marked on the power tool.
Accessories running faster than their
rated speed can break and fly apart.
d. The outside diameter and the thickness
of your accessory must be within the
capacity rating of your power tool.
Incorrectly sized accessories cannot be
adequately controlled.
e. The arbor size of wheels, sanding drums
or any other accessory must properly fit
the spindle or collet of the power tool.
Accessories that do not match the
mounting hardware of the power tool will
run out of balance, vibrate excessively
and may cause loss of control.
f. Mandrel mounted wheels, sanding
drums, cutters or other accessories
must be fully inserted into the collet or
chuck. If the mandrel is insufficiently held
and/or the overhang of the wheel is too
long, the mounted wheel may become
loose and be ejected at high velocity.
g. Do not use a damaged accessory. Before
each use inspect the accessory such as
abrasive wheels for chips and cracks,
sanding drum for cracks, tear or excess
wear, wire brush for loose or cracked
wires. If power tool or accessory is
dropped, inspect for damage or install
an undamaged accessory. After
inspecting and installing an accessory,
position yourself and bystanders away
from the plane of the rotating accessory
and run the power tool at maximum no-
load speed for one minute. Damaged
accessories will normally break apart
during this test time.
h. Wear personal protective equipment.
Depending on application, use face
shield, safety goggles or safety glasses.
As appropriate, wear dust mask, hearing
protectors, gloves and workshop apron
capable of stopping small abrasive or
workpiece fragments. The eye
protection must be capable of stopping
flying debris generated by various
operations. The dust mask or respirator
must be capable of filtrating particles
generated by your operation. Prolonged
exposure to high intensity noise may
cause hearing loss.
i. Keep bystanders a safe distance away
from work area. Anyone entering the
work area must wear personal
protective equipment. Fragments of
workpiece or of a broken accessory may
fly away and cause injury beyond
immediate area of operation.
j. Hold power tool by insulated gripping
surfaces only, when performing an
operation where the cutting accessory
may contact hidden wiring. Cutting
accessory contacting a “live” wire may
make exposed metal parts of the power
tool “liveand could give the operator an
electric shock.
k. Always hold the tool firmly in your
hand(s) during the start-up. The reaction
torque of the motor, as it accelerates to
full speed, can cause the tool to twist.
l. Use clamps to support workpiece
whenever practical. Never hold a small
workpiece in one hand and the tool in
the other hand while in use. Clamping a
small workpiece allows you to use your
hand(s) to control the tool. Round
material such as dowel rods, pipes or
tubing have a tendency to roll while being
cut, and may cause the bit to bind or
jump toward you.
m. Position the cord clear of the spinning
accessory. If you lose control, the cord
may be cut or snagged and your hand or
arm may be pulled into the spinning
accessory.
n. Never lay the power tool down until the
accessory has come to a complete stop.
The spinning accessory may grab the
surface and pull the power tool out of
your control.
o. After changing the bits or making any
adjustments, make sure the collet nut,
Safety Rules for Rotary Tools
5
Safety Rules for Rotary Tools
chuck or any other adjustment devices
are securely tightened. Loose adjustment
devices can unexpectedly shift, causing
loss of control, loose rotating
components will be violently thrown.
p. Do not run the power tool while carrying
it at your side. Accidental contact with
the spinning accessory could snag your
clothing, pulling the accessory into your
body.
q. Regularly clean the power tool’s air
vents. The motor’s fan will draw the dust
inside the housing and excessive
accumulation of powdered metal may
cause electrical hazards.
r. Do not operate the power tool near
flammable materials. Sparks could ignite
these materials.
s. Do not use accessories that require
liquid coolants. Using water or other
liquid coolants may result in electrocution
or shock.
t. Use only in well-ventilated area. Working
in a safe environment reduces risk of
injury.
u. Allow for sufficient space, at least 6”,
between your hand and the spinning bit.
Do not reach in the area of the spinning
bit. The proximity of the spinning bit to
your hand may not always be obvious.
v. Do not touch the bit or collet after use.
After use the bit and collet are too hot to
be touched by bare hands.
w. Do not alter or misuse tool. Any
alteration or modification is a misuse and
may result in serious personal injury.
x. This product is not intended for use as a
dental drill, in human or veterinary
medical applications. Serious injury may
result.
Kickback and Related
Warnings
Kickback is a sudden reaction to a pinched
or snagged rotating wheel, backing pad,
brush or any other accessory. Pinching or
snagging causes rapid stalling of the
rotating accessory which in turn causes the
uncontrolled power tool to be forced in the
direction opposite of the accessory’s
rotation.
For example, if an abrasive wheel is
snagged or pinched by the workpiece, the
edge of the wheel that is entering into the
pinch point can dig into the surface of the
material causing the wheel to climb out or
kickout. The wheel may either jump toward
or away from the operator, depending on
direction of the wheel’s movement at the
point of pinching. Abrasive wheels may also
break under these conditions.
Kickback is the result of power tool misuse
and/or incorrect operating procedures or
conditions and can be avoided by taking
proper precautions as given below.
a. Maintain a firm grip on the power tool
and position your body and arm to allow
you to resist kickback forces. The
operator can control kickback forces, if
proper precautions are taken.
b. Use special care when working corners,
sharp edges etc. Avoid bouncing and
snagging the accessory. Corners, sharp
edges or bouncing have a tendency to
snag the rotating accessory and cause
loss of control or kickback.
c. Do not attach a toothed saw blade. Such
blades create frequent kickback and loss
of control.
d. Always feed the bit into the material in
the same direction as the cutting edge is
exiting from the material (which is the
same direction as the chips are thrown).
Feeding the tool in the wrong direction
causes the cutting edge of the bit to
climb out of the work and pull the tool in
the direction of this feed.
e. When using rotary files, cut-off wheels,
high-speed cutters or tungsten carbide
cutters, always have the work securely
clamped. These wheels will grab if they
become slightly canted in the groove, and
can kickback. When a cut-off wheel grabs,
the wheel itself usually breaks. When a
rotary file, high-speed cutter or tungsten
carbide cutter grabs, it may jump from
the groove and you could lose control of
the tool.
Safety warnings specific for
grinding and abrasive
cutting-off operations:
a. Use only wheel types that are
recommended for your power tool and
only for recommended applications. For
example: do not grind with the side of a
cut-off wheel. Abrasive cut-off wheels are
intended for peripheral grinding, side
forces applied to these wheels may cause
them to shatter.
6
Additional Safety Warnings
a. GFCI and personal protection devices
like electrician’s rubber gloves and
footwear will further enhance your
personal safety.
b. Keep handles dry, clean and free from
oil and grease. Slippery hands cannot
safely control the power tool.
c. Develop a periodic maintenance
schedule for your tool. When cleaning
a tool be careful not to disassemble
any portion of the tool since internal
wires may be misplaced or pinched or
safety guard return springs may be
improperly mounted. Certain cleaning
agents such as gasoline, carbon
tetrachloride, ammonia, etc. may
damage plastic parts.
d. Ensure the switch is in the off position
before inserting battery pack. Inserting
the battery pack into power tools that
have the switch on invites accidents.
b. For threaded abrasive cones and plugs
use only undamaged wheel mandrels
with an unrelieved shoulder flange that
are of correct size and length. Proper
mandrels will reduce the possibility of
breakage.
c. Do not “jam” a cut-off wheel or apply
excessive pressure. Do not attempt to
make an excessive depth of cut.
Overstressing the wheel increases the
loading and susceptibility to twisting or
snagging of the wheel in the cut and the
possibility of kickback or wheel breakage.
d. Do not position your hand in line with
and behind the rotating wheel. When the
wheel, at the point of operation, is
moving away from your hand, the possible
kickback may propel the spinning wheel
and the power tool directly at you.
e. When wheel is pinched, snagged or
when interrupting a cut for any reason,
switch off the power tool and hold the
power tool motionless until the wheel
comes to a complete stop. Never
attempt to remove the cut-off wheel
from the cut while the wheel is in
motion otherwise kickback may occur.
Investigate and take corrective action to
eliminate the cause of wheel pinching or
snagging.
f. Do not restart the cutting operation in
the workpiece. Let the wheel reach full
speed and carefully re-enter the cut. The
wheel may bind, walk up or kickback if
the power tool is restarted in the
workpiece.
g. Support panels or any oversized
workpiece to minimize the risk of wheel
pinching and kickback. Large workpieces
tend to sag under their own weight.
Supports must be placed under the
workpiece near the line of cut and near
the edge of the workpiece on both sides
of the wheel.
h. Use extra caution when making a
“pocket cut” into existing walls or other
blind areas. The protruding wheel may
cut gas or water pipes, electrical wiring or
objects that can cause kickback.
Safety warnings specific for
wire brushing operations:
a. Be aware that wire bristles are thrown
by the brush even during ordinary
operation. Do not overstress the wires
by applying excessive load to the brush.
The wire bristles can easily penetrate
light clothing and/or skin.
b. Allow brushes to run at operating speed
for at least one minute before using
them. During this time no one is to stand
in front or in line with the brush. Loose
bristles or wires will be discharged during
the run-in time.
c. Direct the discharge of the spinning wire
brush away from you. Small particles and
tiny wire fragments may be discharged at
high velocity during the use of these
brushes and may become imbedded in
your skin.
Safety Rules for Rotary Tools
7
a. This manual contains instructions for
battery charger model GAL12V-20. Do
not substitute any other charger.
b. Before using battery charger, read all
instructions and cautionary markings on
(1) battery charger, (2) battery pack,
and (3) product using battery.
c. Charge only Dremel rechargeable
batteries listed on page 13. Other types
of batteries may burst causing personal
injury and damage.
d. Charge battery pack in temperatures
above +32 degrees F (0 degrees C) and
below +113 degrees F (45 degrees C).
Store tool and battery pack in locations
where temperatures will not exceed 120
degrees F (49 degrees C). This is
important to prevent serious damage to
the battery cells.
e. Do not recharge battery in damp or wet
environment. Do not expose charger to
rain or snow. Water entering battery
charger may result in electric shock or
fire.
f. Battery leakage may occur under
extreme usage or temperature
conditions. Avoid contact with skin and
eyes. The battery liquid is caustic and
could cause chemical burns to tissues. If
liquid comes in contact with skin, wash
quickly with soap and water. If the liquid
contacts your eyes, flush them with water
for a minimum of 10 minutes and seek
medical attention.
g. Place charger on flat nonflammable
surfaces and away from flammable
materials when recharging battery pack.
Carpeting and other heat insulating
surfaces block proper air circulation
which may cause overheating of the
charger and battery pack. If smoke or
melting of the charger or battery pack is
observed, unplug the charger immediately
and do not use the battery pack or
charger. Contact customer service
immediately.
h. Make sure cord is located so that it will
not be stepped on, tripped over, or
otherwise subjected to damage or
stress. Damaged plug and cord may
result in electric shock or fire.
i. Disconnect the charger by pulling the
plug rather than the cord. Do not
operate charger with damaged cord or
plug; have them replaced immediately.
Damaged plug or cord may result in
electric shock or fire.
j. Do not insert battery pack in charger if
battery pack case is cracked. Using
damaged battery pack may result in
electric shock or fire.
k. Do not disassemble charger or operate
the charger if it has received a sharp
blow, been dropped or otherwise
damaged in anyway. Incorrect
reassembly or damage may result in
electric shock or fire.
Charger Safety Rules
Read and understand all instructions. Failure to follow all instructions
listed below, may result in electric shock, fire and/or serious personal
injury.
IMPORTANT SAFETY AND OPERATING INSTRUCTIONS
SAVE THESE INSTRUCTIONS
Additional Safety Warnings
Some dust created by
power sanding, sawing,
grinding, drilling, and other construction
activities contains chemicals known to
cause cancer, birth defects or other
reproductive harm. Some examples of
these chemicals are:
Lead from lead-based paints,
Crystalline silica from bricks and cement
and other masonry products, and
Arsenic and chromium from chemically-
treated lumber.
Your risk from these exposures varies,
depending on how often you do this type of
work. To reduce your exposure to these
chemicals: work in a well ventilated area,
and work with approved safety equipment,
such as those dust masks that are specially
designed to filter out microscopic particles.
8
When batteries are not
in tool or charger, keep
them away from metal objects. For
example, to protect terminals from shorting,
DO NOT place batteries in a tool box or
pocket with nails, screws, keys, etc. Fire or
injury may result.
DO NOT PUT BATTERIES INTO FIRE OR
EXPOSE TO HIGH HEAT. They may explode.
Battery Care
Battery Disposal
Do not attempt to disas-
semble the battery or
remove any com ponent projecting from
the battery terminals. Fire or injury may
result. Prior to disposal, protect exposed
terminals with heavy insulating tape to
prevent shorting.
Lithium-ion Batteries
If equipped with a lithium-ion battery, the
battery must be collected, recycled or
disposed of in an environ mentally sound
manner.
“The EPA certified RBRC
Battery Recycling Seal on the
lithium-ion (Li-ion) battery
indicates Robert Bosch Tool
Corporation is voluntarily
participating in an industry
program to collect and recycle these
batteries at the end of their useful life,
when taken out of service in the United
States or Canada. The RBRC program
provides a convenient alterative to placing
used Li-ion batteries into the trash or the
munici pal waste stream, which may be
illegal in your area.
Please call 1-800-8-BATTERY for information
on Li-ion battery recycling and disposal
bans/restrictions in your area, or return
your batteries to a Bosch/Dremel Service
Center for recycling. Robert Bosch Tool
Corporation’s involvement in this program is
part of our commitment to preserving our
environment and conserving our natural
resources.”
Charger Safety Rules
l. Before each use, check the battery
charger, cable and plug. If damage is
detected, do not use the battery
charger. Never open the battery charger
yourself, take it to a Dremel Factory
Service Center, or qualified serviceman
only using original spare parts. Incorrect
reassembly may result in electric shock or
fire.
m. Do not use attachments not
recommended or sold by Dremel. Using
attachments not recommended may
result in electric shock or fire.
n. Do not store battery pack in charger.
Battery pack stored in charger over a long
period of time could lead to battery pack
damage and fire.
o. Unplug charger from outlet before
storage, attempting any maintenance or
cleaning. Such preventive safety
measures reduce the risk of electric
shock or fire.
p. Keep the battery charger clean by
blowing compressed air on charger
vents and wiping the charger housing
with a damp cloth. Contamination may
result in electric shock or fire.
q. Replace battery pack if a substantial
drop in operating time per charge is
observed. Battery pack may be nearing
the end of its life.
9
Licenses
Copyright (c) 2015, Infineon Technologies AG
All rights reserved.
Redistribution and use in source and binary
forms, with or without modification, are
permitted provided that the following
conditions are met:
Redistributions of source code must
retain the above copyright notice, this
list of conditions and the following
disclaimer.
Redistributions in binary form must
reproduce the above copyright notice,
this list of conditions and the following
disclaimer in the documentation and/or
other materials provided with the
distribution.
Neither the name of the copyright
holders nor the names of its contributors
may be used to endorse or promote
products derived from this software
without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE
COPYRIGHT HOLDERS AND
CONTRIBUTORS "AS IS" AND ANY EXPRESS
OR IMPLIED WARRANTIES, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED. IN NO EVENT SHALL THE
COPYRIGHT HOLDER OR CONTRIBUTORS
BE LIABLE FOR ANY DIRECT, INDIRECT,
INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING,
BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS
OF USE, DATA, OR PROFITS; OR BUSINESS
INTERRUPTION) HOWEVER CAUSED AND
ON ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY,OR TORT
(INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE OF
THIS SOFTWARE, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE.
Copyright (c) 2004 - 2020, Texas
Instruments Incorporated
All rights reserved.
Redistribution and use in source and binary
forms, with or without modification, are
permitted provided that the following
conditions are met:
* Redistributions of source code must retain
the above copyright notice, this list of
conditions and the following disclaimer.
* Redistributions in binary form must
reproduce the above copyright notice,
this list of conditions and the following
disclaimer in the documentation and/or
other materials provided with the
distribution.
* Neither the name of Texas Instruments
Incorporated nor the names of its
contributors may be used to endorse or
promote products derived from this
software without specific prior written
permission.
THIS SOFTWARE IS PROVIDED BY THE
COPYRIGHT HOLDERS AND
CONTRIBUTORS "AS IS" AND ANY EXPRESS
OR IMPLIED WARRANTIES, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED. IN NO EVENT SHALL THE
COPYRIGHT OWNER ORCONTRIBUTORS BE
LIABLE FOR ANY DIRECT, INDIRECT,
INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING,
BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS
OF USE, DATA, OR PROFITS; OR BUSINESS
INTERRUPTION) HOWEVER CAUSED AND
ON ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT
(INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE OF
THIS SOFTWARE, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE.
Copyright (c) 2011 ñ 2014, Petteri Aimonen
<jpa at nanopb.mail.kapsi.fi>
This software is provided 'as-is', without any
express or implied warranty. In no event will
the authors be held liable for any damages
arising from the use of this software.
Permission is granted to anyone to use this
software for any purpose, including
commercial applications, and to alter it and
redistribute it freely, subject to the
following restrictions:
1. The origin of this software must not be
misrepresented; you must not claim that
you wrote the original software. If you
use this software in a product, an
acknowledgment in the product
documentation would be appreciated
but is not required.
2. Altered source versions must be plainly
marked as such, and must not be
misrepresented as being the original
software.
3. This notice may not be removed or
altered from any source distribution.
10
FCC Caution:
The manufacturer is not responsible for
radio interference caused by unauthorized
modifications to this equipment. Such
modifications could void the user’s
authority to operate the equipment.
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
1) This device may not cause harmful
interference, and
2) This device must accept any interference
received, including interference that may
cause undesired operation.
NOTE! This equipment generates uses and
can radiate radio frequency energy and, if
not installed and used in accordance with
the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by
turning the equipment off and on, the user
is encouraged to try to correct the
interference by one or more of the following
measures:
Reorient or relocate the receiving
antenna.
Increase the separation between the
equipment and receiver.
Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced
radio/TV technician for help.
This device contains licence-exempt
transmitter(s)/receiver(s) that comply with
Innovation, Science and Economic
Development Canada’s licence-exempt
RSS(s). Operation is subject to the
following two conditions:
(1) this device may not cause interference,
and
(2) this device must accept any
interference, including interference that
may cause undesired operation of the
device.
ISED Canada
Always check tool
settings before use.
Settings may be different than when the
tool was last used. This tool enables
transfer of data and settings based on
Bluetooth® wireless technology. Select tool
settings may be changed remotely by a
paired Bluetooth® device and user installed
app.
This tool is equipped
with a radio interface.
Local operating restrictions, e.g. in military
sites or hospitals, are to be observed.
Transmitters have demonstrated an ability
to unintentionally interfere with other
devices.
Bluetooth®
11
Symbols
Important: Some of the following symbols may be used on your tool. Please study them
and learn their meaning. Proper interpretation of these symbols will allow you to operate
the tool better and safer.
Symbol Designation ⁄ Explanation
V Volts (voltage)
A Amperes (current)
Hz Hertz (frequency, cycles per second)
W Watt (power)
kg Kilograms (weight)
min Minutes (time)
s Seconds (time)
Diameter (size of drill bits, grinding wheels, etc.)
nNo load speed (rotational speed at no load)
n Rated speed (maximum attainable speed)
...⁄min Revolutions or reciprocation per minute (revolutions, strokes, surface
speed, orbits etc. per minute)
Off position (zero speed, zero torque...)
, , , ...
I, II, III,
Selector settings (speed, torque or position settings. Higher number
means greater speed)
0
Infinitely variable selector with off (speed is increasing from  setting)
Arrow (action in the direction of arrow)
Alternating current (type or a characteristic of current)
Direct current (type or a characteristic of current)
Alternating or direct current (type or a characteristic of current)
Class II construction (designates double insulated construction tools)
Earthing terminal (grounding terminal)
12
Symbols
Important: Some of the following symbols may be used on your tool. Please study them
and learn their meaning. Proper interpretation of these symbols will allow you to operate
the tool better and safer.
Symbol Designation / Explanation
Alerts user to read manual.
Alerts user to wear eye protection.
Alerts user to wear respiratory protection.
Alerts user to wear hearing protection.
Alerts user to wear eye, respiratory, and hearing protection.
This symbol designates that this tool is listed by Underwriters
Laboratories, to United States and Canadian Standards.
This symbol designates that this tool is listed by the Canadian
Standards Association.
This symbol designates that this tool is listed by the Canadian
Standards Association, to United States and Canadian Standards.
This symbol designates that this tool is listed by the Intertek Testing
Services, to United States and Canadian Standards.
This symbol designates that this tool complies to NOM Mexican
Standards.
Designates Li-ion battery recycling program.
13
8260
1
5
14
15
16
13
2
3
6
7
8
9
11
12
4
10
Model number . . . . . .8260
Voltage rating . . . . .10.8V/12V MAX
Rated speed . . . . . .n 5,000 - 30,000/min
Collet capacities . . .1/32, 1/16", 3/32", 1/8"
Charger . . . . . . . . . . . .GAL12V-20
Voltage rating . . . . .120 V 60 Hz
Functional Description and Specifications
Model 8260 Cordless Rotary Tool
Battery Packs/Chargers
Please refer to the battery/charger
list included with your tool.
Fig. 1
1. Collet Nut
2. Collet
3. EZ TWIST™ Integrated
Wrench/Nose Cap
4. Shaft
5. Ventilation Openings
6. Shaft Lock Button
7. On/Off Switch
8. Variable Speed Dial
9. Red Warning LED
10. Bluetooth LED
11. Speed Indicator
12. Fuel Gauge
13. Battery Pack
14. Battery Release Tabs
15. Hanger
16. Collet Wrench
14
Inserting and Releasing
Battery Pack
Release battery pack 13 from tool by
pressing on both sides of the battery
release tabs 14 and pull away from
housing (Fig. 2).
To insert battery, align battery and slide
battery pack into tool until it locks into
position. Do not force.
Collet Nut
To loosen, first press shaft lock button 6
and rotate the shaft by hand until the
lock engages the shaft preventing
further rotation. Your Dremel 8260 is
equipped with a quick collet lock
mechanism. This mechanism engages
the output shaft in 8 separate locations
on the shaft for easier operation.
Do not engage lock
while the Rotary Tool
is running.
With the shaft lock engaged use the
collet wrench 16 to loosen the collet nut
1if necessary. The collet nut must be
loosely threaded on when inserting an
accessory. Change accessories by
inserting the new one into the collet as
far as possible to minimize runout and
unbalance. With the shaft lock engaged,
finger tighten the collet nut until the
accessory shank is gripped by the collet
(Fig. 3). Avoid excessive tightening of
the collet nut when there is no bit
inserted.
EZ TWIST™ Integrated
Wrench/Nose Cap
The nose cap of your tool has an
integrated wrench allowing you to
loosen and tighten the collet nut
without the use of the standard collet
wrench. Unscrew the nose cap 3from
the tool, line-up steel insert on inside of
cap with collet nut 1. With the shaft lock
6engaged twist nose cap clockwise to
tighten, and counter-clockwise to loosen
(Fig. 4).
Collets
Four different size collets (Fig. 5), to
accommodate different shank sizes, are
avail able for your Rotary Tool. To install
a different collet, remove the collet nut
and remove the old collet. Insert the
unslotted end of the collet in the hole in
the end of the tool shaft. Replace collet
nut on the shaft.
Assembly
Disconnect battery pack from tool before making any assembly,
adjustments or changing accessories. Such preventive safety measures
reduce the risk of starting the tool accidentally.
1
16
6
To
Loosen
To
Tighten
3
6
1
To
Loosen
To
Tighten
14
13
Fig. 2
Fig. 3
Fig. 4
15
Intended Use
Assembly
Always use the collet
which matches the
shank size of the accessory you plan to
use. Never force a larger diameter shank
into a collet.
Note: Most rotary tool kits do not
include all four collets sizes.
Fixing Stuck Collets
It is possible for a collet to get stuck
within the collet nut especially if a collet
nut is tightened onto the tool without a
bit in place. If this happens, the collet
can be removed from the collet nut by
pushing the shank of an accessory into
the hole in the collet nut (Fig. 6). This
should cause the collet to pop out of the
collet nut.
Balancing Accessories
For precision work, it is important that
all accessories be in good balance
(much the same as the tires on your
automobile). To true up or balance an
accessory, slightly loosen collet nut and
give the accessory or collet a 1/4 turn.
Re tighten collet nut and run the Rotary
Tool. You should be able to tell by the
sound and feel if your accessory is
running in balance. Continue adjusting
in this fashion until best balance is
achieved. To maintain balance on
abrasive wheel points, before each use,
with the wheel point secured in the
collet, turn on the Rotary Tool and run
the 415 Dressing Stone lightly against
the revolving wheel point. This removes
high spots and trues up the wheel point
for good balance.
The hanger is provided for the use of
hanging your tool while using the flex-
shaft or for storage. If you do not use
the hanger, snap it back into place so it
will be out of the way while the tool is in
use.
1
Identification
Rings
480
1/8"
Collet
481
3/32"
Collet 482
1/16"
Collet
483
1/32"
Collet
COLLET IDENTIFICATION CHART
Collet sizes can be identified by the rings
on the back end of collet.
1/32" Collet has one (1) ring.
1/16" Collet has two (2) rings.
3/32" Collet has three (3) rings.
1/8" Collet has no rings (Included in
most tool kits on the tool).
Fig. 5
Fig. 6
This power tool is intended for carving /
engraving, routing, grinding /
sharpening, cutting, cleaning / polishing,
sanding, grout removal and drilling
applications in soft wood, hard wood,
laminates / plastics, steel, aluminum /
brass / copper, shell / stone, ceramic
and glass materials.
16
Whenever you hold
the tool, be careful
not to cover the air vents with your
hand. This blocks the air flow and
causes the motor to overheat.
Slide "On/Off" Switch
The tool is switched "ON" by the slide
switch 7located on the topside of the
motor housing.
TO TURN THE TOOL "ON", slide the
switch button forward.
TO TURN THE TOOL "OFF", slide the
switch button backward.
Learn the Speeds
After the tool has been turned off:
- If you turn it back on within 5
minutes, the tool will turn on at its
last set speed setting.
- If turned on after 5 minutes, the tool
will turn on at its default speed
setting of 15,000 RPM.
Dremel App Connectivity
- Download the Dremel App to your
iOS or Android device from the App
Store or Google Play.
- Install the Dremel App on the smart
device or make sure you are running
the latest version of the app.
- Launch the Dremel App on the smart
device and click on “Connect My
Toolin the “My Dremel” section of
the app.
- Follow the app directions to pair the
tool with the smart device. To pair
the tool with the smart device using
Bluetooth technology, make sure the
tool is turned off and within 1 Meter /
3 Feet of the smart device.
- Once connected the connectivity
range with a clear line of sight is up
to 20 Meters / 65 Feet.
Learn the Speeds
After the tool has been turned off:
- If you turn it back on within 5
minutes, the tool will turn on at its
last set speed setting.
- If turned on after 5 minutes, the tool
will turn on at its default speed
setting of 15,000 RPM.
Variable Speed Dial
Your tool is equipped with a variable
speed dial 8. The speed may be
adjusted during operation by rotating
the dial back or forth between any one
of the settings. One of the numbers on
the speed indicator 11 will light up
showing the current speed (Fig. 7).
You can refer to the charts on page 20
to determine the proper speed, based
on the materi al being worked and the
type of accessory being used. These
Speed
Indicator
Number
Approximate Speed
Range, /min (RPM)
5 4,000-8,000
10 7,000–13,000
•15 12,000–15,000
20 19,000–23,000
25 22,000–25,000
30 26,000–30,000
Wire Brush Setting.
Operating Instructions
Disconnect battery pack from tool before making any assembly,
adjustments or changing accessories. Such preventive safety measures
reduce the risk of starting the tool accidentally.
8260
11 12
8
7
9
10
Fig. 7
17
charts enable you to select both the
correct acces sory and the optimum
speed at a glance.
Increasing the pressure on the tool is
not the answer when it is not
performing as you think it should.
Perhaps you should be using a different
accessory, and perhaps an adjustment
in speed would solve the problem.
Leaning on the tool does not help.
Let speed do the work!
All Dremel Rotary Tool attachments are
compatible with your tool, but you may
experience reduced run times on the
battery when using certain attachments.
Learn the LED Behavior
If you turn off the tool with the battery
still inserted, the tool LEDs will behave
as follows:
- The Speed LED will remain
illuminated for 5 minutes to show the
last set speed setting.
- The Warning and Battery Gauge LEDs
will remain illuminated for 30
seconds.
To turn off all LEDs, remove the
battery pack after the tool has been
turned off.
Managing Speed Settings
- You can preselect a speed between
5,000 30,000 RPM on the Dremel
App.
- Once you have chosen your desired
speed on the app, the corresponding
speed will blink for 10 seconds on
the speed indicator 11 on the tool
(Fig. 7).
- To confirm the app set speed, you
must turn on the tool within 10
seconds.
- If turned on within 5 minutes, the
tool will turn on at its last set speed
setting.
- If turned on after 5 minutes, the tool
will turn on at its default speed
setting of 15,000 RPM.
Learn the LED Behavior
If you turn off the tool with the battery
still connected the tool LEDs will behave
as follows:
- The Bluetooth LED will remain
illuminated for 5 minutes as long as
your tool is still connected to your
smart device.
- The Speed LED will remain
illuminated for 5 minutes to show the
last set speed setting.
- The Warning, Battery Gauge, and
Dremel Logo LEDs will remain
illuminated for 30 seconds.
To turn off all LEDs, turn off the tool
and remove the battery pack.
Red Warning LED
The red warning LED 9will illuminate
for one of the following reasons:
- Excessive tool temperature: turn the
tool off and remove the accessory
(Be careful the accessory may be
hot). Then turn the tool on and
allow it to run without load so the
motor’s fan can help cool down the
tool.
- Excessive battery temperature: turn
the tool off, remove the battery
pack and allow the battery to return
to normal operating temperature
before resuming use.
- Tool stall / overload warning: too
much pressure is being applied to
the tool. Reduce pressure to hold
and guide the tool. Allow the speed
of the tool to do the work.
Bluetooth LED
- The Bluetooth LED 10 indicates the
tool is connected to the smart device
(Fig.7).
- The Bluetooth LED will repeatedly
blink on the tool as it attempts to
connect to the smart device.
- Confirm connection of the tool to
the smart device by turning the
variable speed dial 8in either
direction (Fig. 7).
- After completing this process you
should see the connected tool in the
App and the Bluetooth LED will be
illuminated on the tool and will no
longer be blinking.
Operating Instructions
18
Fuel Gauge
This tool is equipped with a fuel gauge
12 that tells you how much charge your
battery has. A fully charged battery is
indicated when all three LED lights are
illuminated. As the battery discharges,
the lights will turn off one by one until
only one light is on. When the last light
starts "flashing", the battery is almost
empty. When the battery is dead, the
tool will automatically turn off. This will
be a sudden stop as opposed to a
gradual winding down of the tool.
Simply recharge the battery and reuse.
Charging Battery Pack
IMPORTANT CHARGING NOTES
1. The charger was designed to fast
charge the battery only when the
battery temperature is between 32˚F
(0˚C) and 113˚F (45˚C). If the
battery pack is too hot or too cold,
the charger will not fast charge the
battery. (This may happen if the
battery pack is hot from heavy use).
When the battery temperature
returns to between 32˚F (0˚C) and
113˚F (45˚C), the charger will
automatically begin charging.
2. A substantial drop in operating time
per charge may mean that the battery
pack is nearing the end of its life and
should be replaced.
3. Remember to unplug charger during
storage period.
4. If battery does not charge properly:
a. Check for voltage at outlet by
plugging in some other electrical
device.
b. Check to see if outlet is connected
to a light switch which turns power
“offwhen lights are turned off.
c. Check battery pack terminals for
dirt. Clean with cotton swab and
alcohol if necessary.
d. If you still do not get proper
charging, take or send tool, battery
pack and charger to your local
Dremel Service Center.
Note: Use of chargers or battery packs
not recommended by Dremel in the
battery/charger list will void the
warranty.
DREMEL CHARGER GAL12V-20
Plug charger cord into your standard
power outlet, then insert battery pack
13 into charger (Fig. 8).
If the indicator lights are “OFF”, the
charger is not receiving power from
power supply outlet.
The charger’s green indicator light will
begin to “BLINK”. This indicates that the
battery is receiving a fast charge. Fast-
charging will automatically stop when
the battery pack is fully charged.
When the indicator light stops
“BLINKING” (and becomes a steady
green light) fast charging is complete.
The battery pack may be used even
though the light may still be blinking.
The light may require more time to stop
blinking depending on temperature.
3 lights – 70–100% charge remaining
2 lights – 40–70% charge remaining
1 light – 20–40% charge remaining
1 "flashing" light – Below 20% charge
remaining. Be prepared for tool to
shut off.
Operating Instructions
Green Light
Charger
13
Fig. 8
19
Service
NO USER SERVICE -
ABLE PARTS INSIDE.
Preventive maintenance performed by
un au thorized personnel may result in
misplacing of internal wires and
components which could cause serious
hazard. We recom mend that all tool
service be performed by a Dremel
Service Center. SERVICE MEN:
Disconnect tool and/or charger from
power source before servicing.
Batteries
Be alert for battery packs that are
nearing their end of life. If you notice
decreased tool performance or
significantly shorter running time
between charges then it is time to
replace the battery pack. Failure to do
so can cause the tool to operate
improperly or damage the charger.
D.C. Motors
The motor in your tool has been
engineered for many hours of
dependable service. To maintain peak
efficiency of the motor, we recommend
it be examined every six months. Only a
genuine Dremel replacement motor
specially designed for your tool should
be used.
Cleaning
Certain cleaning
agents and solvents
damage plastic parts. Some of these
are: gasoline, car bon tetrachloride,
chlorinated cleaning solvents, ammonia
and household detergents that contain
ammonia.
Ventilation openings and switch levers
must be kept clean and free of foreign
matter. Do not attempt to clean by
inserting pointed objects through
opening
Maintenance
To avoid accidents, always disconnect the tool and/or charger from the
power supply before servicing or cleaning.
The purpose of the blinking green light
is to indicate that the battery pack is
fast-charging. It does not indicate the
exact point of full charge. The light will
stop blinking in less time if the battery
pack was not completely discharged.
If the green indicator light is "ON", the
charger is plugged in but the battery
pack is not inserted, or the battery pack
is fully charged, or the battery pack is
too hot or cold for fast-charging. The
charger will automatically switch to fast-
charging once a suitable temperature is
reached.
When charging several batteries in
sequence, the charge time may slightly
increase.
When the battery pack is fully charged,
unplug the charger (unless you're
charging another battery pack) and slip
the battery pack back into the tool.
Operating Instructions
20
Dremel Accessories
Use only Dremel® branded accessories. Other accessories are not
designed for this tool and may lead to personal injury or property
damage.
Store accessories in a dry and temperate environment to avoid corrosion and
deterioration.
The number and variety of accessories for the Rotary Tool are almost limitless. There is a
category suited to almost any job you might have to do and a variety of sizes and shapes
within each category which en ables you to get the perfect accessory for every need.
The accessory categories are as follows; carving / engraving, routing, grinding / sharpening,
cutting, cleaning / polishing, sanding, grout removal, drilling and collets / miscellaneous.
For a complete Dremel rotary accessory guide please visit -
dremel.com/documents/20812/597949/bit-guide-poster.pdf
Speed Settings
Cutting Accessories
Catalog Number Soft
Wood Hard
Wood Laminates
/Plastics Steel Aluminum,
Brass, etc. Shell/
Stone Ceramic Glass
EZ456 - - - 25-30 25-30 - - -
EZ476 - - 5-10 - - - - -
The following charts are recommended speeds for each accessory and material type.
Note: Each number settings listed in the speed charts = x 1,000 RPM
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72

Dremel 8260 Manuel utilisateur

Catégorie
Outils électroportatifs
Taper
Manuel utilisateur

dans d''autres langues