Poulan PP4218AV TYPE 1 Le manuel du propriétaire

Marque: Poulan

Modèle: PP4218AV TYPE 1

Catégorie: Tronçonneuses électriques

Taper: Le manuel du propriétaire

Ce manuel convient également à

Poulan PRO /

Instruction Manual

Manual de Instrucciones

Manuel d'lnstructions

PP3816AV / PP4218AV

PP4218AVL

For Occasional Use Only

WARNING:

Read and follow all Safety Rules and Operating Instructions before

using this product. Failure to do so can result in serious injury.

ADVERTENCIA:

Lea el manual de instrucciones y siga todas las advertencias e en-

strucciones de seguridad. El no hacerlo puede resultar en lesiones

graves.

AVERTISSEMENT:

Lire le manuel d'instructions et bien respecter tousles avertisse-

merits et toutes les instructions de securite. Tout defaut de le faire

pourrait entra_ner des blessures graves.

Electrolux Home Products, Inc. Eiectrolux Consumer Outdoor Products

1030 Stevens Creek Road 5855 Terry Fox Way

Augusta, GA 30907 Mississauga, Ontario L5V 3E4

[_ The Elecb'olux Group. The world's No. 1 choice.

KITCHEN,, CLEANING ann OUTnO_ APPLI_VCm3 COMSINED

WARNING! This chain saw

can be dangerous! Careless or

improper use can cause serious

or even fatal injury.

Always wear appropriate

ear protection, eye protec-

tion and head protection.

Read and understand the

instruction manual before

using the chain saw.

Measured maximum kick-

back value without chain

brake for the bar and chain

combination on the label

Always use two hands when operating the chain saw.

WARNING! Contacting the guide bar tip with any ob-

ject shoutd be avoided; tip contact may cause the guide

bar to move suddenly upward and backward, which may

cause serious injury.

Starting Reminder

Move ON/STOP switch to

_ _ the ON position.

Prime 6X Slowly press primer bulb

(_)_ 6 times.

Full Choke

®%

Pull choke/fast idle lever

out to the full extent (to

the FULL CHOKE posi-

tion).

Pull 5X Pull the starter rope

sharply 5 times with your

('-_ b_ _ right hand.

,_--_ Push the choke/fast idle

/2 lever in to the HALF

Halt Choke CHOKE position.

f'_'b_i Pull the starter rope sharply

with your right hand until

Pull to Start the engine starts.

,_ WARNING: Always disconnect

spark plug wire and place wire where itcan-

not contact spark plug to prevent accidental

starting when setting up, transporting, ad-

justing or making repairs except carburetor

adjustments.

Because a chain saw is a high-speed wood-

cutting tool, special safety precautions must

be observed to reduce the risk of accidents.

Careless or imp.roper use of this tool can

cause serious injury.

PLAN AHEAD

• Read this manual carefully until you com-

pletely understand and can follow all safety

rules, precautions, and operating instruc-

tions before attempting to use the unit.

• Restrict the use of your saw to adult users

who understand and can follow safety

rules, precautions, and operating instruc-

tions found in this manual.

• Wear protective gear. Always use steeF

toed safety footwear with non-slip soles;

snug-fitting clothing; heavy-duty, non-slip

gloves; eye protection such as non-fog-

ging, vented goggles or face screen; an

approved safety hard hat; and sound barri-

ers (ear plugs or mufflers) to protect your

hearing. Regular users should have hear-

ing checked regularly as chain saw noise

can damage hearing. Secure hair above

shoulder length.

Hearing . / Safety Hat

Protection

-__. _._ Eye

"_l u"ell_ Protection

Snug

Fitting Heavy Duty

Clothing Gloves

Safety Safety Chaps

Shoes

• Keep all parts of your body away from the

chain when the engine is running.

• Keep children, bystanders, and animals a

mh_imum of 30 feet (10 meters) away from

the work area. Do not allow other people

or animals to be near the chain saw when

starting or operating the chah_ saw.

• Do not handle or operate a chain saw when

you are fatigued, ill, or upset, or if you have

taken aIcohol, drugs, or medication. You

must be in good physical condition and men-

tally alert. Chain saw work is strenuous. If

you have any condition that might be aggra-

vated by strenuous work, check with your

doctor before operating a chain saw.

• Carefully plan your sawing operation in ad-

vance. Do not start cutting until you have a

clear work area, secure footing, and, if you

are felling trees, a planned retreat path.

OPERATE YOUR SAW SAFELY

• Do not operate a chain saw with one hand.

Serious injury to the operator, helpers, by-

standers or any combination of these per-

sons may result from one-handed opera-

tion. A chain saw is intended for

two-handed use.

• Operate the chain saw only in a welFventi-

lated outdoor area.

• Do not operate saw from a ladder or in a

tree.

• Make sure the chain will not make contact

with any object while starting the engine.

Never try to start the saw when the guide

bar is in a cut.

• Do not put pressure on the saw at the end

of the cut. Applying pressure can cause

you to lose control when the cut is com-

pleted.

• Stop the engine before setting the saw

down.

• Do not operate a chain saw that is dam-

aged, improperly adjusted, or not com-

pletely and securely assembled. Always

replace bar, chain, hand guard, or chain

brake immediately if it becomes damaged,

broken or is otherwise removed.

• With the engine stopped, hand carry the

chain saw with the muffler away from your

body, and the guide bar and chain to the

rear, preferably covered with a scabbard.

MAINTAIN YOUR SAW IN GOOD

WORKING ORDER

• Haveailchainsawserviceperformed bya

qualified service dealer with the exception

of the items listed in the maintenance sec-

tion ofthis manual. For example, ifimprop-

er tools are used to remove or hold the fly-

wheel when servicing the clutch, structural

damage to the flywheel can occur and

cause the flywheel to burst.

• Make certain the saw chain stops moving

when the throttle trigger is released. For

correction, refer to CARBURETOR AD-

JUSTMEN_R

• Never modify your saw in any way.

• Keep the handles dry, clean, and free of oil

or fuel mixture.

• Keep fuel and oil caps, screws, and fas-

teners securely tightened.

• Use only Poulan PRO_: accessories and

replacement parts as recommended.

HANDLE FUEL WITH CAUTION

• Do not smoke while handling fuel or while

operating the saw.

• Eliminate all sources of sparks or flame in

the areas where fuel is mixed or poured.

There should be no smoking, open flames,

or work that could cause sparks. Allow en-

gine to coot before refueling.

• Mix and pour fuel in an outdoor area on

bare ground; store fuel in a cool, dry, well

ventilated place; and use an approved,

marked container for all fuel purposes.

Wipe up all fuel spills before starting saw.

• Move at least 10 feet (3 meters) from fueF

ing site before starting engine.

• Turn the engine off and let saw cool in a

non-combustible area, not on dry leaves,

straw, paper, etc. Slowly remove fuel cap

and refuel unit.

• Store the unit and fuel in an area where fuel

vapors cannot reach sparks or open

flames from water heaters, electric motors

or switches, furnaces, etc.

KICKBACK

WARNING: Avoid kickback which

can result in serious injury. Kickback is the

backward, upward or sudden forward motion

of the guide bar occurring when the saw

chain near the upper tip of the guide bar con-

tacts any object such as a log or branch, or

when the wood closes in and pinches the

saw chain in the cut. Contacting a foreign ob-

ject in the wood can also result in loss of

chain saw control.

• Rotational Kickback can occur when the

moving chain contacts an object at the up-

per tip of the guide bar. This contact can

cause the chain to dig into the object,

which stops the chain for an instant. The

result is a lightning fast, reverse reaction

which kicks the guide bar up and back to-

ward the operator.

• Pinch-Kickback can occur when the the

wood closes in and pinches the moving

saw chain in the cut along the top of the

guide bar and the saw chain is suddenly

stopped. This sudden stopping of the

chainresultsinareversalofthechain

forceusedtocutwoodandcausesthe

sawtomoveintheoppositedirectionofthe

chainrotation.Thesawisdrivenstraight

backtowardtheoperator.

• Pull4n can occur when the moving chain

contacts a foreign object in the wood in the

cut along the bottom of the guide bar and the

saw chain is suddenly stopped. This sudden

stopping pulls the saw forward and away

from the operator and could easily cause the

operator to lose control of the saw.

Avoid Pinch-Kickback:

• Be extremely aware of situations or ob-

structions that can cause material to pinch

the top of or otherwise stop the chain.

• Do not cut more than one log at a time.

• Do not twist the saw as the bar is with-

drawn from an undercut when bucking.

Avoid Pull-In:

• Always begin cutting with the engh_e at full

speed and the saw housh_g against wood.

• Use wedges made of plastic or wood.

Never use metal to hold the cut open.

\X_,\ ,Jr: Kickback Path

there is greater chance of kickback occur-

ring.

• Cut one log at a time.

• Use extreme caution when re-entering a

previous cut.

• Do not attempt cuts starting with the tip of

the bar (plunge cuts).

• Watch for shifting logs or other forces that

could close a cut and pinch or fall into

chain.

• Use the Reduced-Kickback Guide Bar

and Low-Kickback Chain specified for

your saw.

MAINTAIN CONTROL

Stand to the

hand positions

Thumb on

underside of

handlebar

Elbow locked

Clear The Working Area

REDUCE THE CHANCE OF

KICKBACK

• Recognize that kickback can happen.

With a basic understanding of kickback,

you can reduce the element of surprise

which contributes to accidents.

• Never let the moving chain contact any ob-

ject at the tip of the guide bar.

• Keep the working area free from obstruc-

tions such as other trees, branches, rocks,

fences, stumps, etc. Eliminate or avoid

any obstruction that your saw chain could

hit while you are cutting. When cutting a

branch, do not let the guide bar contact

branch or other objects around it.

• Keep your saw chain sharp and properly

tensioned. A loose or dull chain can in-

crease the chance of kickback occurring.

Follow manufacturer's chain sharpening

and maintenance instructions. Check ten-

sion at regular intervals with the engine

stopped, never with the engine running.

Make sure the bar nuts are securely tight-

ened after tensioning the chain.

• Beginandcontinuecuttingatful_speed. If

the chain is moving at a slower speed,

Thumb on underside of

handlebar

• Keep a good, firm grip on the saw with both

hands when the engine is running and

don't let go. A firm grip will help you reduce

kickback and maintain control of the saw.

Keep the fingers of your left hand encir-

cling and your left thumb under the front

handlebar. Keep your right hand com-

pletely around the rear handle whether

your are right handed or teft handed. Keep

your left arm straight with the elbow

locked.

• Position your left hand on the front handle-

bar so it is in a straight line with your right

hand on the rear handle when making

bucking cuts. Never reverse right and left

hand positions for any type of cutting.

• Stand with your weight evenly balanced on

both feet.

• Stand slightly to the left side of the saw to

keep your body from being in a direct line

with the cutting chain.

• Do not overreach. You could be drawn or

thrown off balance and lose control of the

SaW.

• Do not cut above shoulder height, it is diffi-

cult to maintain control of saw above

shoulder height.

KICKBACKSAFETY FEATURES

WARNING: The following features

are included on your saw to he_p reduce the

hazard of kickback; however, such features

will not totally eliminate this danger. As a

chain saw user, do not rely only on safety de-

vices. You must follow ali safety precau-

tions, instructions, and maintenance in this

manual to help avoid kickback and other

forces which can result in serious h3jury.

• Reduced-Kickback Guide Bar, designed

with a small radius tip which reduces the

size of the kickback danger zone on the

bar tip. A Reduced-Kickback Guide Bar

has been demonstrated to significantly re-

duce the number and seriousness of kick-

backs when tested in accordance with

safety requirements for gasoline powered

chain saws as set by ANSi B175.1.

Reduced Kickback Symmetrical Guide Bar

_all Radius Tip

Large Radius Tip

• Low-Kickback Chain, designed with a

contoured depth gauge and guard link

which deflect kickback force and allow

wood to gradually ride into the cutter. Low-

Kickback Chain has met kickback per-

formance requirements when tested on a

representative sample of chain saws be-

low 3.8 cubic inch displacement specified

in ANSI B175.1.

Contoured Depth Gauge

D Elongated Guard Link

....

Low-Kickback _ and allowswood

Chain to gradually ride

into cufter

• Front Hand Guard, designed to reduce the

chance of your left hand contacting the chain

if your hand slips oft the front handlebar.

• Position of front and rear handlebars, de-

signed with distance between hand}es and

"in-line" with each other. The spread and

"in-line" position of the hands provided by

this design work together to give balance

and resistance in controlling the pivot of

the saw back toward the operator if kick-

back occurs.

CHAIN BRAKE AND CKA ANGLE

• Chain Brake, designed to stop the chain in

the event of kickback.

_I, WARNING: WE DO NOT REP-

RESENT AND YOU SHOULD NOT AS-

SUME THAT THE CHAIN BRAKE WiLL

PROTECT YOU IN THE EVENT OF A KICK-

BACK, Kickback is a lightning fast action

which throws the bar and rotating chain back

and up toward the operator, Kickback can be

caused by allowing contact of the bar tip in the

danger zone with any hard object, Kickback

can also be caused by pinching the saw chain

along the top of tt_eguide bar. This action may

push the guide bar rapidly back toward the op-

erator. Either of these events may cause you

to lose control of the saw which could result in

serious injury or even death. DO NOT RELY

UPON ANY OF THE DEVICES BUILT INTO

YOUR SAW. YOU SHOULD USE THE SAW

PROPERLY AND CAREFULLY TO AVOID

KICKBACK. Reduced-kickback guide bars

and low-kickback saw chains reduce the

chance and magnitude of kickback and are

recommended, Your saw has a low kickback

chain and bar as original equipment, Repairs

on a chain brake should be made by an autho-

rized servicing dealer. Take your unit to the

place of purchase if purchased from a servic-

ing dealer, or to the nearest authorized master

service dealer.

• Tip contact in some cases may cause a light-

ning fast reverse REACTION, kicking guide

bar up and back toward operator.

• Pinching the saw chain along the top of the

guide bar may push the guide bar rapidly

back toward the operator.

• Either of these reactions may cause you to

lose control of the saw which could result in

serious injury. Do not rely exclusively upon

devices built into your saw,

_IL WARNING: Computed kickback

angle (CKA) listed on your saw and listed inthe

CKA table below represents angle of kickback

your bar and chain combinations will have

when tested in accordance with CSA (Cana-

dian Standards Association) and ANSi stan-

dards. When purchasing replacement bar and

chain, considerations should be given to the

lower CKA values, Lower CKA values repre-

sent safer angles to the user, higher values in-

dicate more angle and higher kick energies.

Computed angles represented indicate total

energy and angle associated without activation

of the chain brake during kickback, Activated

angle represents chain stopping time relative to

activation angle of chain break and resulting

kick angle of saw, In all cases lower CKA val-

ues represent a safer operating environment

for the user.

The following guide bar and chain combina-

tions meet kickback requirements of CSA

Standards Z62,1, Z62.3, & ANSI B175.1 when

used on saws listed in this manual. Use of bar

and chain combinations other than those listed

is not recommended and may not meet the

CKA requirements per standard,

Computed kickback angle (CKA) Table

BAR

MODEL P/N Length CHAIN P/N CKAwithout chain brake

PP3816AV 952044942

PP4218AV / PP4218AVL 952044926

NOTE: If this saw is to be used for com-

mercial logging, a chain brake is required

and shall not be removed or otherwise dis-

abled to comply with Federal OSHA Regula-

tions for Commercial Logging.

SAFETY NOTICE: Exposure to vibrations

through prolonged use of gasoline bowered

hand tools could cause blood vessel or nerve

damage in the fingers, hands, and joints of

people prone to circulation disorders or

abnormal swellings. Prolonged use in cold

weather has been linked to blood vessel

damage in otherwise healthy people. If

symptoms occur such as numbness, pain,

loss of strength, change in skin color or texture,

or loss of feeling in the fingers, hands, or joints,

discontinue the use of this tool and seek

medical attention. An anti-vibration system

does not guarantee the avoidance of these

problems. Users who operate power tools on

a continual and regular basis must monitor

closely their physical condition and the

condition of this tool

SPECIAL NOTICE: Your saw is equipped

with a temperature limiting muffler and spark

arresting screen which meets the

requirements of California Codes 4442 and

16" 952051211 33 °

18" 952051338 33 °

4443. All U.S. forest land and the states of

California, idaho. Maine, Minnesota, New

Jersey. Oregon, and Washington require by

law that many internal combustion engines to

be equipped with a spark arresting screen. If

you operate a chain saw in a state or locale

where such regulations exist, you are legally

responsible for maintaining the operating

condition of these parts. Failure to do so is a

violation of the law. Refer to the SERVICE

section for maintenance of the spark arresting

screen. Failure to follow all Safety Rules and

Precautions can result in serious injury. If

situations occur which are not covered in this

manual, use care and good judgement. If you

need assistance, contact your authorized

service dealer or call 1-800-854-6723.

STANDARDS: This saw is listed by Under-

writer's Laboratories, Inc., in accordance with:

ANSI B175.1-2000 American National

Standards for Gasoline-Powered Chain

Saws - Safety Requirements

CSA Z62.1-03 Chain Saws - Occupational

Hea_th and Safety

CSA Z62.3-96 Chain Saw Kickback Occu-

pational Health and Safety

Protective gloves (not provided) should be

worn during assembly.

ATTACHING TH E BAR & CHAIN (If not

already attached)

WARNING: If received assembled,

repeat all steps to ensure your saw is properly

assembled and all fasteners are secure. Al-

ways wear gloves when handling the chain.

The chain is sharp and can cut you even when

it is not moving!

1. Loosen and remove the bar nuts and the

clutch cover from the saw.

2. Remove the plastic shipping spacer (if

present).

3. Turn adjusting screw on bar counterclock-

wise to move the tensioning rack as far as

it will go toward the front of the bar.

(_o _,o _ Adjusting

Screw

Tensioning Rac_kk _

4. Slide guide bar on bar bolts until guide bar

stops against clutch drum sprocket.

Clutch cover"

Bar nuts Location of

"_ shipping

_!_ spacer

Chain adjustment tool _=====_

(Bar Tool) '_

Bar bolts

Guide bar'"_'_

5. Carefullyremovethechainfromthepack-

age.Holdchainwiththedrivelinksas Guide

shown. Bar

Tipof

Bar

;UTTERS MUST FACE IN

DIIREOTION QF ROTATION

Cutters Depth Gauge

Drive Links

6. Place chain over and behind the clutch

retainer, fitting the drive links in the

clutch drum sprocket.

7. Fit bottom of drive links between the

teeth in the sprocket in the nose of the

guide bar.

8. Fit chain drive links into bar groove.

9. Pull guide bar forward until chain is snug

in guide bar groove. Ensure all drive

links are in the bar groove.

10. Hold guide bar against the saw frame

and install clutch cover.

11. Install bar nuts and finger tighten only.

Once the chain is tensioned, you will

need to tighten bar nuts.

CHAIN TENSION

(Including units with chain already h_stalled)

WARNING: Wear protective gloves

when handling chain. The chain is sharp and

can cut you even when it is not movh_g.

NOTE: When adjusting chain tension,

make sure the bar nuts are finger tight only.

Attempting to tension the chain when the bar

nuts are tight can cause damage.

Checking the tension:

Use the screwdriver end of the chain adjust-

ment tool (bar tool) to move chain around

guide bar. If the chain does not rotate, itis too

tight. Ifthe chain is too loose, itwill sag below

the bar.

Chain Adjustment

Tool

Bar Nuts (Bar Tool)

Adjusting the tension:

Chain tension is very h_qportant. Chains

stretch during use. This is especially true

during the first few times you use your saw.

Always check chain tension each time you

use and refuel your saw.

An adjusting screw (located on the guide

bar) is used to adjust the tension of the chain

(see illustration).

1. Turn adjusting screw clockwise until chain

solidly contacts bottom of guide bar rail.

Guide bar

Adjusting

Screw

2. Using bar tool. roll chain around guide bar

to ensure all links are in bar groove.

3. Lift up tip of guide bar to check for sag.

Release tip of guide bar. then turn ad-

justing screw clockwise until sag does

not exist.

4. While lifting tip of guide bar, tighten bar

nuts securely with the bar tool.

5. Use the screwdriver end of the bar tool

to move chain around guide bar.

6. If chain does not rotate, it is too tight.

Slightly loosen bar nuts and loosen

chain by turning the adjusting screw.

Retighten bar nuts.

7. If chain is too loose, it will sag below the

guide bar. DO NOT operate the saw if

the chain is loose.

_i, WARNING: If the saw is operated

with a loose chain, the chain could jump off

the guide bar and result in serious injury.

KNOW YOUR CHAIN SAW

READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR

CHAIN SAW. Compare the illustrations with your unit to familiarize yourself with the location of

the various controls and adjustments. Save this manual for future reference.

Front Handle

Chain

Front Hand Guard

Adjustment Tool _ Starter Rope

(Bar Tool)

Chain Muffler

ON/STOP

Switch Choke/

Pastldle

Lever

Bar

Sprocket

Hole

Throttle

Lockout

Rear

Handle

Bar Oil Fill Cap

Cylinder Cover

Starter Housing

Fuel Mix Fill Cap

Chain

Primer Bulb

Chain

Direction

of Travel

ThrottIe

Trigger Clutch Cover Bar Nuts

ON/STOP SWITCH

The ON/STOP SWITCH is used to stop the

engine.

THROTTLE TRIGGER

The THROTi-LE TRIGGER controls engine

speed.

THROTTLE LOCK-OUT

The THROTTLE LOCK-OUT must be

pressed before you can squeeze the throttle

trigger. This feature prevents you from acci-

dentally squeezing the trigger.

CHOKE/FAST IDLE LEVER

The choke and fast idle are set by pulling the

CHOKE/FAST IDLE LEVER out to the full ex-

tent for cold starting or after refueling. The

choke provides additional fuel to the engine

during cold starting.

PRIMER BULB

The PRIMER BULB circulates fuel to the car-

buretor to provide quicker starting.

Guide Bar

Catcher

CHAIN BRAKE

The chain brake is a device designed to stop

the chain if kickback occurs. The chain brake

activates automatically in the event of kick-

back. The chain brake activates manually ifthe

front hand guard is pushed forward. The chain

brake is disengaged by pulling the front hand

guard back toward the front handle as far as

possible.

CHAIN TENSION

It is normai for a new chain to stretch during the

first 15 minutes of operation. You should check

your chain tension frequently. See CHAIN

TENSION under the ASSEMBLY section.

_L, WARNING: Muffler is very hot dur-

ing and after use. Do not touch the muffler or

allow combustible material such as dry

grass or fuel to do so.

BEFORE STARTING ENGINE

_ WARNING: Be sure to read the fuel

handling information in the safety rules sec-

tion of this manual before you begin. If you do

not understand the fuel handling h_formation

do not attempt to fuel your unit. Seek help

from someone that does understand the h_-

formation or call the customer assistance

help line at 1-800-554-6723.

FUELING ENGINE

_ WARNING: Remove fuel cap slow-

ly when refueling.

HELPFUL I

To obtain the correct oilmix I

r/ ratio, pour 3.2 ounces of I

'/ 2-cycle synthetic oil into I

one gallon of fresh gas. J

is certified to operate on un-

leaded gasoline. Before operation, gasoline

must be mixed with a good quality synthetic

2-cycle air-cooled engine oil designed to be

mixed at a ratio of 40:1. PouIan/Weed Eater

brand synthetic oil is recommended. A 40:1

ratio is obtained by mixing 3.2 ounces (95 ml)

of oil with 1 gallon (4 liters) of unleaded gaso-

lh_e. Included with this saw is a 3.2 ounce (95

ml) container of Poulan/Weed Eater brand syn-

thetic oil. Pour the entire contents of this con-

tainer into 1 gallon (4 liters) of gasoline to

achieve the proper fuel mixture.

DO NOT USE automotive or marine oil

These oils will cause engine damage. When

mixing fuel follow the instructions printed on

the container. Always read and follow the

safety rules listed under HANDLE FUEL

WITH CAUTION.

BAR AND CHAIN LUBRICATION

The bar and chain require continuous lubri-

cation. Lubrication is provided by the auto-

matic oiler system when the oil tank is kept

filled. Lack of oil will quickly ruin the bar and

chain. Too littIe oil will cause overheating

shown by smoke coming from the chain and/

or discoloration of the bar.

In freezing weather oil will thicken, making it

necessary to thin bar and chain oil with a

small amount (5 to 10%) of #1 Diesel Fuel or

kerosene. Bar and chain oil must be free

flowing for the oil system to pump enough oil

for adequate _ubrication.

Genuine Poulan or Poulan PRO_; bar and

chain oil is recommended to protect your unit

against excessive wear from heat and fric-

tion. PouIan or Poulan PRO% oil resists

high temperature thinning.

If Poulan or Poulan PRO_; bar and chain oil

is not available, use a good grade SAE 30 oil.

• Never use waste oil for bar and chain lubri-

cation.

• Always stop the engine before removing

the oil cap.

IMPORTANT

Experience indicates that alcohol-blended

fuels (called gasohol or using ethanol or meth-

anol) can attract moisture which leads to sepa-

This engine

ration and formation of acids during storage.

Acidic gas can damage the fuel system of an

engine while in storage. To avoid engine prob-

lems, the fuel system should be emptied before

storage for 30 days or longer. Drain the gas

tank, start the engine and let it run until the fuel

lines and carburetor are empty. Use fresh fuel

next season. See STORAGE section for addi-

tional information.

CHAIN BRAKE

Ensure chain brake is disengaged by pulling

the front hand guard back toward the front han-

dle as far as possible. The chain brake must be

disengaged before cutting with the saw.

_bWARNING: The chain must not

move when the engine runs at idle speed. If

the chain moves at idle speed refer to CAR-

BURETOR ADJUSTMENT within this

manual. Avoid contact with the muffler. A hot

muffler can cause serious burns.

To stop the engine move the ON/STOP

switch to the STOP position.

To start the engine hold the saw firmly on

the ground as illustrated. Make sure the

chain is free to turn without contacting any

object.

Use only 15" - t8" (40 - 45 cm) of

rope per puff.

Hold saw firmly while pulling starter rope.

Starter Rope Handle

Left Hand

on Front

Handle

Right Foot Through Rear Handle

IMPORTANT POINTS TO REMEMBER

When pulting the starter rope, do not use the

full extent of the rope as this can cause the

rope to break. Do not let starter rope snap

back. Hold the handle and let the rope re-

wind slowly.

For cold weather starting, start the unit at

FULL CHOKE; allow the engine to warm up

before squeezing the throttle trigger.

NOTE: Do not attempt to cut material with

the choke/fast idle lever in the FULL CH O KE

position.

I HELPFUL TIP I

ff your engine etill doee not I

start after following these I

instructions, please call

1-800-554-6728.

STARTING A COLD ENGINE (or warm

engine after running out of fuel)

NOTE: In the following steps, when the

choke/fast idle lever is pulled out to the full

extent, the correct throttle setting for starting

is set automatically.

IGNITION

SWITCH

STOP

Lever

1. MoveON/STOPswitchtotheONposi-

tion.

2. Slowlypressprimerbulb6times.

3. Pullchoke/fastidleleverouttothefull

extent(totheFULLCHOKEposition).

4. Pullthestarterropesharply5timeswith

yourrighthand.Then.proceedtothe

nextstep.

NOTE:Iftheenginesoundsasifitistrying

tostartbeforethe5thpull,stoppullingand

immediatelyproceedtothenextstep.

5. Pushthechoke/fastidleleverintothe

HALFCHOKEposition.

CHOKE/FASTIDLELEVER

OFF

HALF

FULL

6. Pull the starter rope sharply with your

right hand until the engine starts.

7. Allow the engine to run for approximate-

ly 30 seconds. Then. squeeze and re-

lease the throttle trigger to allow engine

to return to idle speed.

STARTING A WARM ENGINE

1. Move ON/STOP switch to the ON posi-

tion.

2. Slowly press primer bulb 6 times.

3. Pull the choke/fast idle lever out to the

FULL CHOKE position to set the fast

idle, then push the lever in to the HALF

CHOKE position.

4. Pull the starter rope sharply with your

right hand until the engine starts.

5. Squeeze and release throttle trigger to

allow engine to return to idle speed.

DIFFICULT STARTING (or starting a

flooded engine)

The engine may be flooded with too much

fuel if it has not started after 10 pulls.

Flooded engines can be cleared of excess

fuel by pushing the choke/fast idle lever in

completely (to the OFF CHOKE position)

and then following the warm engine starting

procedure listed above. Ensure the ON/

STOP switch is in the ON position.

Starting could require pulling the starter rope

handle many times depending on how badly

the unit isflooded. If engine fails to start, refer

to the TROUBLESHOOTING TABLE or call

1-800-554-6723.

CHAIN BRAKE

_,WARNING: If the brake band is

worn too thin it may break when the chain

brake is triggered. With a broken brake band,

the chain brake will not stop the chain. The

chain brake should be replaced by an autho-

rized service dealer ifany part is worn to less

than 0.020" (0.5 mm) thick. Repairs on a

chain brake should be made by an autho-

rized service dealer. Take your unit to the

place of purchase if purchased from a ser-

vicing dealer, or to the nearest authorized

master service dealer.

• This saw is equipped with a chain brake.

The brake is designed to stop the chain if

kickback occurs.

• The inertia-activated chain brake is

activated if the front hand guard is pushed

forward, either manually (by hand) or

automatically (by sudden movement).

• If the brake is already activated, it is

disengaged by pulling the front hand guard

back toward the front handle as far as

possible.

• When cutting with the saw. the chain brake

must be disengaged.

Disengaged

Engaged

.... _ /

Braking function control

CAUTION: The chain brake must be

checked several times daily. The engine

must be running when performing this proce-

dure. This is the only instance when the saw

should be placed on the ground with the en-

gine running.

Place the saw on firm ground. Grip the rear

handle with your right hand and the front han-

dle with your left hand. Apply full throttle by

fully depressing the throttle trigger. Activate

the chain brake by turning your left wrist

against the hand guard without releasing

your grip around the front handle. The chain

should stop immediately.

Inertia activating function control

_WARNING: When performing the

following procedure, the engine must be

turned off.

G rip the rear handle with your right hand and

the front handle with your left hand, Hold the

chain saw approximately 14" (35 cm) above

a stump or other wooden surface. Release

your grip on the front handle and use the

weight of the saw to let the tip of the guide bar

fall forward and contact the stump. When the

tip of the bar hits the stump, the brake should

activate.

OPERATING TIPS

• Check chain tension before first use and

after 1 minute of operation. See CHAIN

TENSION in the ASSEMBLY section.

• Out wood only. Do not out metal, plastics,

masonry, non-wood building materials, etc.

• Stop the saw if the chain strikes a foreign

object. Inspect the saw and repair or re-

place parts as necessary.

• Keep the chain out of dirt end sand. Even a

small amount of dirt wilt quickly dull a chain

and thus increase the possibility of kickback.

• Practice cutting a few small logs using the

following techniques to get the "feel" of us-

ing your saw before you begin a major

sawing operation.

• Squeeze the throttle trigger and allow the

engine to reach full speed before cutting.

• Begin cutting with the sew frame

against the log.

• Keep the engine at full speed the entire

time you are cutting.

• Allowthechaintooutforyou. Exertonly

light downward pressure. If you force

the cut, damage to the bar, chain, or en-

gine can result.

• Release the throttle trigger as soon as

the cut is completed, allowing the en-

gine to idle. If you run the sew at full

throttle without a cutting load, unneces-

sary wear can occur to the chain, bar,

and engine, It is recommended that

the engine not be operated for lon-

ger than 30 seconds at full throttle.

• To avoid losing control when cut is com-

plete, do not put pressure on saw at end

of cut.

• Stop the engine before setting the saw

down after cutting.

TREE FELLING TECHNIQUES

_WARNING: Check for broken or

dead branches which can fall while cutting

causing serious injury, Do not cut near build-

ings or electrical wires if you do not know the

direction of tree fall, nor cut at night since you

will not be ale to see well, nor during bad

weather such as rain, snow, or strong winds,

etc. if the tree makes contact with any utility

line, the utility company should be notified

immediately.

• Carefully plan your sawing operation in ad-

vance.

• Cleartheworkarea, You needacteararee

all around the tree so you can have secure

footing.

• The chain sew operator should keep on

the uphill side of the terrain as the tree is

likely to roll or slide downhill after it is felled.

• Study the natural conditions that can cause

the tree to fall in a particular direction.

Natural conditions that can cause a tree to

fall in a particular direction include:

• The wind direction and speed.

• The lean of the tree. The lean of a tree

might not be apparent due to uneven or

sloping terrain. Use a plumb or level to de-

termine the direction of tree lean.

• Weight and branches on one side.

• Surrounding trees and obstacles.

Look for decay and rot. If thetrunk is rotted,

it can snap and fall toward the operator.

Check for broken or dead branches which

can fall on you while cutting.

Make sure there is enough room for the tree to

fail. Maintain a distance of 2-1/2 tree lengths

from the nearest person or other objects. En-

gine noise can drown out a warning call.

Remove dirt, stones, loose bark, nails, sta-

ples, end wire from the tree where cuts are to

be made.

Plan a clear retreat path to the rear and diag-

onal to the line of fall.

_ Plan a clear retreat path

;_.... _.,_-"_- Direction of Fall

45 ° /

jkxe_-t"

FELLING LARGE TREES

(6 inches (15 ore) in diarneter or larger)

The notch method is used to fell large trees.

A notch is cut on the side of the tree in the de-

sired direction of fall. After a felling cut is

made on the opposite side of tree, the tree

will tend to fall into the notch.

NOTE: If the tree has large buttress roots,

remove them before making the notch. Ifus-

ing saw to remove buttress roots, keep saw

chain from contacting ground to prevent dull-

ing of the chain.

NOTCH CUT AND FELLING THE

TREE

• Make notch cut by cutting the top of the

notch first. Out through 1/3 of the diameter

of the tree. Next complete the notch by cut-

ring the bottom of the notch. See illustra-

tion. Once the notch is cut remove the

notch of wood from the tree.

Final (felling) cut here, 2 inches

(5 cm) above center of notch.

First cut } Z'; [ /

Notch ...,_t _ _J_[ =,.

• After removing the wood from the notch,

make the felling cut on the opposite side of

the notch. This is done by making e cut about

two inches (5 cm) higher than the center of

the notch. This will leave enough uncut wood

between the felling cut and the notch to form

a hinge. This hinge will help prevent the tree

from falling in the wrong direction.

Hinge holds tree on stump and helps

control fall

Opening

of felling

Closing of

notch

NOTE: Before felHng cut is complete, use

wedges to open the cut if necessary to

control the direction of fall. To avoid kickback

and chain damage, use wood or plastic

wedges, but never steel or iron wedges.

• Be alert to signs that the tree is ready to

fall: cracking sounds, widening of the fell-

ing cut, or movement in the upper

branches.

• As tree starts to fall stop saw, put it down,

and get away quickly on your planned re-

treat path.

• DO NOT cut down a partialIy fallen tree

with your saw. Be extremely cautious with

partially fallen trees that may be poorly

supported, When a tree doesn't fall com-

pletely, set the saw aside and pul_down the

tree with a cable winch, block and tackle,

or tractor.

CUTTING A FALLEN TREE

(BUCKING)

BucMng is the term used for cutting a fallen

tree to the desired log size,

_ WARNING: Do not stand on the log

being cut. Any portion can roll causing loss

of footing and control. Do not stand downhill

of the log being cut.

IMPORTANT POINTS

• Cut only one log at a time.

• Cut shattered wood very carefully; sharp

pieces of wood could be flung toward opera-

tor,

• Use a sawhorse to cut small logs. Never

allow another person to hold the log while

cutting and never hold the tog with your leg

or foot,

• Do not cut in an area where logs, limbs,

and roots are tangled such as in a blown

down area. Drag the logs into a clear area

before cutting by pulling out exposed and

cleared logs first,

TYPES OF CUTTING USED FOR

BUCKING

_WARNING: If saw becomes

pinched or hung in a log, don't try to force it

out, You can lose control ofthe saw resulting

in injury and/or damagetothe saw. Stopthe

saw, drive a wedge of plastic or wood into the

cut until the saw can be removed easily. Re-

start the saw and carefully reenter the cut. To

avoid kickback and chain damage, do not

use a metal wedge, Do not attempt to restart

your saw when it is pinched or hung in a log.

Use a wedge to remove pinched saw

Turn saw OFF and use a plastic or

wooden wedge to force cut open,

Overcutting begins on the top side of the log

with the bottom of the saw against the tog.

When overcutting use light downward pres-

sure.

Overcutt,ng

Undercutting "" *_:,

Undercutting involves cutting on the under-

side of the log with top of saw against the log.

When undercutting use light upward pres-

sure. Hold saw firmly and maintain control.

The saw will tend to push back toward you,

_, WARNING: Never turn saw upside

down to undercut, The saw cannot be con-

trolled in this position,

Always make your first cut on the compres-

sion side of the log, The compression side of

the log is where the pressure of the log's

weight is concentrated,

First cut on compression side of log

Second cut

First cut on compression side of tog

BUCKING WITHOUT A SUPPORT

• Overcut through 1/3 of the diameter of the

log.

• Roll the log over and finish with a second

overcut,

• Watch for logs with a compression side to

prevent the saw from pinching, See il-

lustrations for cutting logs with a compres-

sion side.

BUCKING USING A LOG OR

SUPPORT STAND

• Remember your first cut is always on the

compression side of the log,

(Refer to the illustrations below for your

first and second cut)

• Your first cut should extend 1/3 of the

diameter of the log,

• Finish with your second cut.

Using a log for support

2 nd Cut

I st Cut

Using a support stand

2 nd Cut X_

._,,_ I st Cut

LIMBING AND PRUNING

WARNING: Be alert for and guard

against kickback, Do not allow the moving

chain to contact any other branches or objects

at the nose of the guide bar when limbing or

pruning. Allowing such contact can result in

serious injury.

WARNING: Neverolimbintoatreeto

limb or prune. Do not stand on ladders, plat-

forms, a log, or in any position which can cause

you to tose your balance or control of the saw.

IMPORTANT POINTS

• Work slowly, keeping both hands firmly

gripped on the saw. Maintain secure footing

and balance.

• Watch out for springpoles. Springpoles are

small size limbs which can catch the saw

chain and whip toward you or pull you off bal-

ance. Use extreme caution when cutting

small size limbs or slender material

• Be alert for springback. Watch out for

branches that are bent or under pressure.

Avoid being struck by the branch or the

saw when the tension in the wood fibers is

released.

• Keep a clear work area. Frequently clear

branches out of the way to avoid tripping

over them.

LIMBING

• Always limbatreeafter itis cutdown. Only

then can limbing be done safely and prop-

erly.

• Leave the larger limbs underneath the felled

tree to support the tree as you work.

• Start at the base of the felled tree and work

toward the top, cutting branches and limbs.

Remove small limbs with one cut.

• Keep the tree between you and the chain.

Out from the side of the tree opposite the

branch you are cutting.

• Remove larger, supporting branches with

the cutting techniques described in BUCK-

ING WITHOUT A SUPPORT.

• Always use an overcut to cut small and free-

ly hanging limbs. Undercutting could cause

limbs to fall and pinch the saw.

PRUNING

_b WARNING: Limit pruning to limbs

shoulder height or below. Do not cut if

branches are higher than your shoulder. Get a

professional to do the job.

• Make your first cut 1/3of the way through the

bottom of the limb,

• Next make a 2rid cut all the way through

the limb. Then cut a third overcut leaving a

1 to 2 inch (2.5 to 5 cm) collar from the truck

of the tree.

_ThiPrd! Sec°nd cut_Y'_'_

Collar tit_

X,,_!_ _ First cut

/ Pruning technique

,.%

,e_WARNING: Disconnect the spark

plug before performing maintenance except

for carburetor adjustments.

We recommend all service and adjustments

not listed in this manual be performed by an

authorized or Master Service Dealer.

HELPFUL TIP

IMPORTANT: Hav e all

f_'k repairs ether than the rec-

[_ I,_ _ ommended maintenance

_ .,J,_/ described in the instruction

_ manuat performed by an

authorized service dealer.

If any dealer other than an authorized

service dealer performs work on the

product, Electrolux Home Products.

Inc.. may not pay for repairs under war-

ranty. Itis your responsibility to maintain

and perform general maintenance.

MAINTENANCE SCHEDULE

Check:

Fuel mixture level .... Before each use

Bar lubrication ....... Before each use

Chain tension ....... Before each use

Chain sharpness ..... Before each use

For damaged parts ... Before each use

For loose caps ...... Before each use

For loose fasteners... Before each use

For loose parts ...... Before each use

Inspect and Clean:

Bar ................ Before each use

Complete saw ....... After each use

Air filter ............. Every 5 hours*

Chain brake ......... Every 5 hours*

Spark arresting screen

and muffler .......... Every 25 hours*

Replace spark plug . Yearly

Replace fuel filter ... Yearly

* Hours of Operation -

Each hour of operation is approximately

2 tanks of fuel.

GENERAL RECOMMENDATIONS

The warranty on this unit does not cover

items that have been subjected to operator

abuse or negligence. To receive full value

from the warranty, the operator must main-

tain unit as instructed in this manual. Various

adjustments will need to be made periodicaF

ly to properly maintain your unit.

• Onceayear, replacett_e spark plug. airfilter,

and check guide bar and chain for wear. A

new spark plug and air filter assures proper

air-fuel mixture and helps your engine run

better and last longer.

CHECK FOR DAMAGED OR

WORN PARTS

Contact an authorized service dealer for re-

placement of damaged or worn parts.

NOTE: It is normal for a small amount of oil

to appear under the saw after engine stops.

Do not confuse this with a leaking oil tank.

• ON/STOP Switch - Ensure ON/STOP

switch functions properly by moving the

switch to the STOP position. Make sure en-

gine stops; then restart engine and continue.

• Fuel Tank - Do not use saw if fuel tank

shows signs of damage or leaks.

• Oil Tank - Do not use saw if oil tank shows

signs of damage or leaks.

CHECK FOR LOOSE

FASTENERS AND PARTS

Bar Nuts

Chain

Muffler

Cylinder Shield

Air Filter

Handle Screws

Vibration Mounts

Starter Housing

Front Hand Guard

CHECK CHAIN SHARPNESS

A sharp chain makes wood chips. A dull

chain makes a sawdust powder and cuts

slowly. See CHAIN SHARPENING.

CHECK GUIDE BAR

Conditions which require guide bar mainte-

nance;

• Saw cuts to one side or at an angle.

• Saw has to be forced through the cut.

• Inadequate supply of oil to bar/chain.

Check the condition of guide bar each time

chain is sharpened. A worn guide bar will

damage the chain and make cutting difficult.

After each use. ensure ON/STOP switch is

in the STOP position, then clean all sawdust

from the guide bar and sprocket hole.

To maintain guide bar:

• Move ON/STOP switch to STOP.

• Loosen and remove bar nuts and clutch

cover. Remove bar and chain from saw.

• Clean the oil holes and bar groove after

each 5 hours of operation.

Remove Sawdust From _ _

Guide Bar G_ov__._"

Oil Holes * a

• Burring of guide bar rails is a normal

process of rail wear. Remove these burrs

with a flat file.

• When rail top is uneven, use afiat file to re-

store square edges and sides.

'_ File Rail Edges_ r] r]

and Sides I U I

Square I I

Worn Groove Correct Groove

Replace guide bar when the groove is worn,

the guide bar is bent or cracked, or when ex-

cess heating or burring of the rails occurs. If re-

placement is necessary, use only the guide bar

specified for your saw in the repair parts list or

on the decal located on the chain saw.

CHECK FUEL MIXTURE LEVEL

• See FUELING ENGINE under the OP-

ERATION section.

LUBRICATION

Bar Oil

Fill Cap

• See GUIDE BAR AND CHAIN OIL under

the OPERATION section.

INSPECT AND CLEAN UNIT AND

DECALS

• After each use. inspect complete unit for

loose or damaged parts. Clean the unit and

decals using a damp cloth with a mild deter-

gent.

• Wipe off unit with a clean dry cloth.

CHECK CHAIN BRAKE

See CHAIN BRAKE in the OPERATION

section.

CLEAN AIR FILTER

CAUTION: Do not clean filter in gasoline or

other flammable solvent to avoid creath_g a

fire hazard or producing harmful evaporative

emissions.

Cleaning the air filter:

A dirty air filter decreases the life and perfor-

mance of the engine and h_creases fuel con-

sumption and harmful emissions. Always

clean your air filter after 10 tanks of fuel or 5

hours of operation, whichever comes first.

Clean more frequently h_dusty conditions. A

used air filter can never be completely

cleaned. It is advisable to replace your air fil-

ter with a new one after every 50 hours of op-

eration, or annually, whichever comes first.

1. Loosen 3 screws on cyIinder cover.

2. Remove cylinder cover.

3. Remove air filter cover and air filter.

4. Clean the air filter using hot soapy water.

Rinse with clean cool water. Air dry com-

pletely before reinstalling.

5. Reinstall air filter and air filter cover.

6. Reinstall cylinder cover and 3 screws.

Tighten securely.

Air Filter

Cover

Cylinder

Cover

INSPECT MUFFLER AND SPARK

ARRESTING SCREEN

_WARNING: The muffler on this

product contains chemicals known to the

State of California to cause cancer.

As the unit is used, carbon deposits build up

on the muffler and spark arresting screen,

and must be removed to avoid creating a fire

hazard or affecting engine performance.

Replace the spark arresting screen if breaks

OCCUr.

Spark Exhaust

Arresting Outlet

Screen Cover

Nut

Muffler

CLEANING THE SPARK ARREST-

ING SCREEN

Cleaning is required every 25 hours of op-

eration or annually, whichever comes first.

1. Loosen and remove the nut from the ex-

haust outlet cover.

2. Remove the exhaust oulet cover.

3. Remove spark arresting screen. Handle

screen carefully to prevent damage.

4. Clean the spark arresting screen gently

with a wire brush. Replace screen if

breaks are found.

5. Replace any broken or cracked muffler

parts.

6. Reinstall spark arresting screen, exhaust

outlet cover, and nut. Tighten nut securely.

REPLACE SPARK PLUG

The spark plug should be replaced each

year to ensure the engine starts easier and

runs better, ignition timing is fixed and non-

adjustable.

1. Loosen 3 screws on cyfinder cover.

2. Remove the cylinder cover.

3. Pull off the spark plug boot.

4. Remove spark plug from cylinder and

discard.

5. Replace with Champion RCJ-7Y spark

plug and tighten securely with a 3/4 inch

(19 mm) socket wrench. Spark plug gap

should be 0.025 inch (0,6 mm).

6. Reinstall the spark plug boot.

7. Reinstall the cylinder cover and 3

screws. Tighten securely.

Cylinder

Cover

Plug Boot

Spark

Plug

REPLACE FUEL FILTER

To replace fuel fi_ter, drain your unit by run-

ning it dry of fuel. Remove fuel cap and its

connected retainer from tank. Pull filter from

tank and remove from line. Replace and re-

assemble.

CHAIN ADJUSTMENT

See CHAIN TENSION in ASSEMBLY section.

CHAIN SHARPENING

Chah_ sharpening is a complicated task and

requires special tools. We recommend that

you refer chain sharpening to a professional

chain sharpener.

CARBURETOR ADJUSTMENT

_lk WARNING: The chain will be moving

during most of this procedure. Wear your pro-

tective equipment and observe all safety pre-

cautions. The chain must not move at idle

speed.

The carburetor has been carefully set at the

factory. Adjustments may be necessary if

you notice any of the foflowing conditions:

• Chain moves at idle. See iDLE SPEED-T

adjusting procedure.

• Saw will not idle. See IDLE SPEED-T ad-

justing procedure.

Idle Speed-T

Allow engine to idle. If the chain moves, idle is

too fast. If tt_eengine stalls, idle is too slow. Ad-

just speed until engine runs without chain

movement (idle too fast) or stalling (idle too

slow). The idle speed screw is located in the

area above the primer bulb and is tabeled T.

• Turn idle screw (T) clockwise to increase

engine speed.

• Turn idle screw (T) counterclockwise to

decrease engine speed.

if you require further assistance or are unsure

about performing this procedure, contact your

authorized service dealer or call our customer

assistance help line at t -800-554-6723.

WARNING: Perform the following

steps after each use:

• AHow the engine to coo], and secure the

unit before storing or transporting,

• Store chain saw and fuel in a well venti-

lated area where fuel vapors cannot reach

sparks or open flames from water heaters,

electric motors or switches, furnaces, etc.

• Store chain saw with all guards in place

and position chain saw so that any sharp

object cannot accidentally cause injury.

• Store chain saw well out of the reach of

children.

SEASONAL STORAGE

Prepare your unit for storage at the end of the

season or if it will not be used for 30 days or

more.

If your chain saw is to be stored for a period

of time:

• Clean saw thoroughly before storage.

• Store in a clean dry area.

• Lightly oil external metal surfaces and

guide bar.

• Oil the chain and wrap it in heavy paper or

cloth.

FUEL SYSTEM

Under FUELING ENGINE in the OPERA-

TION section of this manual, see message

labeled IMPORTANT regarding the use of

gasohol in your chain saw.

Fuel stabilizer is an acceptable alternative in

minimizing the formation of fuel gum depos-

its during storage. Add stabilizer to the gaso-

line in the fuel tank or fuel storage container.

Follow the mix instructions found on stabiliz-

er containers. Run engine at least 5 minutes

after adding stabilizer.

Poulan/Weed Eater 40:1,2-cycle engine oil

(air cooled) is blended with fuel stabilizer. If

you do not use this oil, you can add a fuel sta-

bilizer to your fuel tank.

HELPFUL TIP ]

During storage of your gae/ |

/rj]_l_,_" _ oil mixture, the oil will sep a- |

[_Fl_l]l_l rate from the gas. |

_J[_'._] We recommend that you |

_lJlrJ Shake the gas can weekly |

to insure proper blending of |

the gas and oi!. J

ENGINE

• Remove spark plug and pour 1 teaspoon

of 40:1, 2-cycle engine oil (air cooled)

through the spark plug opening. Slowly

pull the starter rope 8 to 10 times to distrib-

ute oil.

• Replace spark plug with new one of rec-

ommended type and heat range.

• Clean air filter.

• Check entire unit for loose screws, nuts,

and bolts. Replace any damaged, broken,

or worn parts.

• At the beginning of the next season, use

only fresh fuel having the proper gasoline

to oil ratio.

OTHER

• Do not store gasolh_e from one season to

another.

• Replace your gasoline can if it starts to

rust.

TROUBLESHOOTING TABLE

_, WARNING: Always stop unit and disconnect spark plug before performing all of

the recommended remedies below except remedies that require operation of the unit.

TROUBLE REMEDY

Engine wilt not

start or will run

only a few

seconds after

starting.

CAUSE

1. ignition switch off,

2. Engine flooded.

3. Fuel tank empty.

4. Spark plug not firing.

5. Fuel not reaching

carburetor.

1. Move ignition switch to ON.

2. See "Difficult Starting" in

Operation Section.

3. Fill tank with correct fuel mixture.

4. Install new spark plug.

5. Check for dirty fuel filter; replace.

Check for kinked or split fuel line;

repair or replace.

1. See "Carburetor Adjustment" in the

Service and Adjustments Section.

2. Contact an authorized service dealer.

Engine will 1. Idle speed requires

not idle adjustment.

properly. 2. Carburetor requires

adjustment.

Engine wil_ not 1. Air filter dirty. 1. C_eae or replace air filter.

accelerate. 2. Spark p_ug fouled. 2. Clean or replace plug and regap.

lacks power. 3. Chain brake engaged. 3. Disengage chain brake.

or dies under 4. Carburetor requires 4. Contact an authorized service dealer.

a load. adjustment.

Engine 1. Too much oil mixed with 1. Empty fuel tank and refill with

smokes gasoline, correct fuel mixture.

excessively.

Chain moves 1. Idle speed requires 1. See "Carburetor Adjustment" in the

at idle speed, adjustment. Service and Adjustments Section.

2. Clutch requires repair. 2. Contact an authorized service dealer.

ELECTROLUX HOME PRODUCTS, INC.,

warrants to the origh_al purchaser that each

new Poulan PRO<_ brand gasoline chain

saw is free from defects in material and

workmanship and agrees to repair or replace

under this warranty any defective gasoline

chain saw as follows from the original date of

purchase.

1 YEAR - Parts and Labor, when used for

Household purposes.

60 DAYS - Parts and Labor, when used for

Commercial, Professional, or Income Pro-

ducing purposes.

30 DAYS - Parts and Labor, if used for rental

purposes.

This warranty is not transferable and does

not cover damage or liability caused by im-

proper handling, improper maintenance, or

the use of accessories and/or attachments

not specifically recommended by ELEC-

TROLUX HOME PRODUCTS, INC., for this

chain saw. Additionalty, this warranty does

not cover damage caused by improper han-

dling, improper maintenance, or if the saw is

altered in any way which in our judgement af-

fects its condition or operation. This warranty

does not cover tune-up, spark plugs, filters,

starter ropes, starter springs, chain sharpen-

ing, bars, chains, and other parts which wear

and require replacement with reasonable

use during the warranty period. This warran-

ty does not cover predelivery set-up, instaF

lation of guide bar and chain, and normal ad-

justments explained in the instruction

manual such as carburetor adjustments and

chain tension adjustments. This warranty

does not cover transportation costs.

THIS WARRANTY GIVES YOU SPECIFIC

LEGAL RIGHTS, AND YOU MAY HAVE

OTHER RIGHTS WHICH VARY FROM

STATE TO STATE.

NO CLAIMS FOR CONSEQUENTIAL OR

OTHER DAMAGES WILL BE ALLOWED,

AND THERE ARE NO OTHER EXPRESS

WARRANTIES EXCEPT THOSE EX-

PRESSLY STIPULATED HEREIN.

SOME STATES DO NOT ALLOW LIMITA-

TIONS ON HOW LONG AN IMPLIEDWAR-

RANTY LASTS OR THE EXCLUSION OR

LiMiTATiONS OF INCIDENTAL OR CON-

SEQUENTIAL DAMAGES, SO THE

ABOVE LIMITATIONS OR EXCLUSION

MAY NOT APPLY TO YOU.

The policy of ELECTROLUX HOME PRO-

DUCTS, INC., is to continuously improve its

products. Therefore, ELECTROLUX HOME

PRODUCTS, INC., reserves the right to

change, modify, or discontinue models, de-

signs, specifications, and accessories of all

products at any time without notice or obliga-

tion to any purchaser.

YOUR WARRANTY RIGHTS AND OBLIGA-

TIONS: The U.S. Environmental Protection

Agency, California Air Resources Board, Envi-

ronment Canada and ELECTROLUX HOME

PRODUCTS, INC., are pleased to explain the

emissions control system warranty on your

year 2005 and later small off-road engine. In

California, atl small off-road engines must be

designed, built, and equipped to meet the

State's stringent anti-smog standards. ELEC-

TROLUX HOME PRODUCTS, INC., must

warrant the emission control system on your

small off-road engine for the periods of time

listed below provided there has been no abuse,

neglect, or improper maintenance of your small

off-road engine. Your emission control system

includes parts such as the carburetor and the

ignition system. Where a warrantable condition

exists, ELECTROLUX HOME PRODUCTS,

INC., will repair your small off-roed engine en-

gine at no cost to you. Expenses covered un-

der warranty include diagnosis, parts and labor.

MANUFACTURER'S WARRANTY COVER-

AGE: if any emissions related part on your en-

gine (as listed under Emissions Control War-

ranty Parts List) is defective or a defect in the

materials or workmanship of the engine

causes the failure of such an emission related

part, the part will be repaired or replaced by

ELECTROLUX HOME PRODUCTS, INC.

OWNER'S WARRANTY RESPONSlBIU-

TIES: As the small off-roed engine engine

owner, you are responsible for the perfor-

mance of the required maintenance listed in

your instruction manual. ELECTROLUX

HOME PRODUCTS, INC., recommends that

you retain all receipts covering maintenance on

your small off-road engine, but ELECTROLUX

HOME PRODUCTS, iNC., cannot deny war-

ranty solely for the lack of receipts or for your

failure to ensure the performance of all sched-

uled maintenance. As the smaII off-road en-

gine engine owner, you should be aware that

ELECTROLUX HOME PRODUCTS, INC.,

may deny you warranty coverage if your small

off-road engine engine or a part of it has failed

due to abuse, neglect, improper maintenance,

unapproved modifications, or the use of parts

not made or approved by the original equip-

ment manufacturer. You are responsible for

presenting your small off-road engine to an

ELECTROLUX HOME PRODUCTS, INC.,

authorized repair center as soon as a problem

exists. Warranty repairs should be completed

in a reasonable amount of time, not to exceed

30 days. If you have any questions regarding

your warranty rights and responsibilities, you

should contact your nearest authorized service

center or call ELECTROLUX HOME PROD-

UCTS, iNC., at 1-800-554-6723.

WARRANTY COMMENCEMENT DATE:

The warranty period begins on the date the

smafl off-toed engine is purchased. LENGTH

OF COVERAGE: This warranty shall be for a

period of two years from the initial date of pur-

chase. WHAT IS COVERED: REPAIR OR

REPLACEMENT OF PARTS. Repair or re-

placement of any warranted part will be per-

formed at no charge to the owner at an ap-

proved ELECTROLUX HOME PRODUCTS,

INC,, servicing center. If you have any ques-

tions regarding your warranty rights and re-

sponsibilities, you should contact your nearest

authorized service center or call ELECTRO-

LUX HOME PRODUCTS. INC., at

1-800-554-6723. WARRANTY PERIOD:

Any warranted part which is not echeduled for

replacement as required maintenance, or

which is scheduled only for regular inspection

to tt_e effect of"repair or replace as necessary"

shall be warranted for 2 years. Any warranted

part which is scheduled for replacement as re-

quired maintenance shaII be warranted for the

period of time up to the first scheduled replace-

ment point for that part. DIAGNOSIS: The

owner shall not be charged for diagnostic labor

which leads to the determination that a war-

ranted part is defective if the diagnostic work is

performed at an approved ELECTROLUX

HOME PRODUCTS, INC., servicing center.

CONSEQUENTIAL DAMAGES: ELECTRO-

LUX HOME PRODUCTS, INC., may be liable

for damages to other engine components

caused by the failure of a warranted part still

under warranty.

WHAT IS NOT COVERED: All failures caused

by abuse, neglect, or improper maintenance

are not covered. ADD-ON OR MODIFIED

PARTS: The use of add-on or modified parts

can be grounds for disallowing a warranty

claim, ELECTROLUX HOME PRODUCTS,

iNC,, isnot liable to cover failures of warranted

parts caused by the use of add-on or modified

parts, HOW TO FILE A CLAIM: if you have

any questions regarding your warranty rights

and responsibilities, you should contact your

nearest authorized service center or call

ELECTROLUX HOME PRODUCTS, INC,, at

1-800-554-6723. WHERE TO GET WAR-

RANTY SERVICE: Warranty services or re-

pairs shall be provided at all ELECTROLUX

HOME PRODUCTS. INC., service centers.

Call: t-800-554-6723 MAINTENANCE, RE-

PLACEMENT AND REPAIR OF EMISSION

RELATED PARTS: Any ELECTROLUX

HOME PRODUCTS, iNC,, approved replace-

ment part used in the performance of any war-

ranty maintenance or repair on emission re-

lated parts will be provided without charge to

the owner ifthe part is under warranty. EMIS-

SION CONTROL WARRANTY PARTS LIST:

Carburetor, Ignition System: Spark Plug (cov-

ered up to maintenance schedule), Ignition

Module, Muffler including catalyst. MAINTE-

NANCE STATEMENT: The owner is responsi-

ble for the performance of all required mainte-

nance as defined in the instruction manual,

The information on the product label indicates which standard your engine is certified.

Example: (Year) EPA Phase 1 or Phase 2 and/or CALIFORNIA.

I GI I 81 I

This engine is certified to be emissions compliant for the following use:

[] Moderate (50 hours)

]intermediate (125 hours)

[] Extended (300 hours)

ADVERTENClA:iEsta

sierra de cadena puede ser

peligrosa! El uso descuidado

o indebido de esta herramienta

puede causar graves heridas.

Use siempre la protecci6n de

oidos apropiada, la protecci6n de

ojos y la protecci6n de la cabeza.

Lea y comprenda el

manual de instruc-

ciones antes de usar

la sierra.

MAXimo valor de kickback

medido sin et freno de

cadena para la combinaci6n

de barra y cadena indicada

en la etiqueta.

Use siempre las dos manos cuando trabaje con la sierra de

cadena.

ADVERTENClA: Debe evitarsecualquier contactode

la punta de labarra guia con cualguier objeto, ya que puede

causar que la barra guia se desplace repentinamente hacia

arriba y hacia atr&.s, con posibles graves heridas.

Simbolos

Prime 6X

Full Choke

®%

de atranque

Mueva el interruptor ON/

STOP a la posici6n ON.

Lentamente, optima el

bombeador 6 veces.

Tire de la patanca del

cebador/marcha lenta rapida

su maxima extensi6n (a la

posici6n FULL CHOKE).

Pull 5X

tgPb_dl

Half Choke

Pull to Start

Firmemente, tire del man-

go de la cuerda de arran-

que 5 veces con su mano

derecha.

Empuje ta palanca del

cebador/marcha lenta rapida

a la posici6n HALF CHOKE.

qqre del mango de la cuerda

de arranque con su mano

derecha hasta que el motor

se ponga en marcha.

_ ADVERTENCIA: Desconecte

siempre el cable de la bujia y col6quelo

donde no puede entrar en contacto con el

bujia, para evitar cualquier arranque acci-

dental al preparar, transportar, ajustar o re-

parar el aparato, excepto en el case de

ajustes al carburador.

Debido a que tas sierras de cadena son instru-

mentos para cortar madera a atta velocidad,

deben observarse precauciones de seguridad

especiaies para reducir el riesgo de acci-

dentes. El uso descuidado o indebido de esta

herramienta puede causar graves hefidas.

PIENSE ANTES DE PROCEDER

• Antes de utitizar ta sierra, lea attentamente

este manual hasta estar seguro o compren-

derlo completamente y poder seguir todas

las reglas de segufidad, precauci6ns e

instrucciones de uso que se dan en el.

• Umite el uso de la sierra a aquelIos usuarios

adultos que comprendad y puedan imple-

mentar todas las precauciones, regtas de

seguridad e instrucciones de uso que se en-

cuentran en este manual.

• Use equipo protector. Siempre use calzado

de seguridad con puntas de acero y suelas

anti-deslizantes; ropa ajustada el cuerpo;

guantes gruesos de uso industrial anti-desli-

zantes; protecci6n de ojos tales como gafas

de seguridad que no se empa[flan y con ab-

erturas de ventillacion o mascara protectora

La page charge ...

Poulan PP4218AV TYPE 1 Le manuel du propriétaire

Marque: Poulan

Modèle: PP4218AV TYPE 1

Catégorie: Tronçonneuses électriques

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Poulan PP4218AV TYPE 1 Owner's manual
español: Poulan PP4218AV TYPE 1 El manual del propietario

Poulan PP4218AV TYPE 1 Le manuel du propriétaire

Ce manuel convient également à

Poulan PP4218AV TYPE 1 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents