Mark OptiTherm Plus 06 29 189 Technical Manual

Technical manual

Technisches Handbuch

Livret technique

Technisch boek

Instrukcja techniczna

Manual tehnic

EN

DE

FR

NL

OptiTherm+

0664013

06 29 189

OptiTherm+

06 29 189

PL

RO

Contents

Warnings ..............................................................................................................................................page 3

1.0 General

1.1 Subject to change ..............................................................................................................page 3

1.2 General warnings .............................................................................................................. page 3

1.3 Type of thermostat and application .............................................................................page 3

2.0 Technical data

2.1 Technical data ....................................................................................................................page 4

2.2 Factory settings .................................................................................................................page 5

3.0 Installation and initial starting

3.1 General ..............................................................................................................................page 5

3.2 Placing ..................................................................................................................................page 5

3.3 Cabling .................................................................................................................................page 5

3.4 Mounting and installation ................................................................................................ page 6

3.5 First initial operation ........................................................................................................page 7

4.0 Operation

4.1 Explanation of buttons .....................................................................................................page 8

4.2 Explanation of display and symbols .............................................................................page 9

4.3 Frost protection ................................................................................................................page 10

4.4 Switching on/off the heating mode ...............................................................................page 10

4.5 Switching on/off the ventilation mode .........................................................................page 10

4.6 Switching on/off the overtime timer (extend timer) ................................................ page 10

5.0 Change settings

5.1 Call user menu ..................................................................................................................page 11

5.2 User menu: Change temperature setting ..................................................................page 11

5.3 User menu: Set/change clock program ........................................................................page 12

5.4 User menu: Set/change exception day .........................................................................page 12

5.5 User menu: Call settings menu......................................................................................page 13

5.6 Settings menu: Change date/time ..................................................................................page 14

5.7 Settings menu: Change overtime timer settings ........................................................ page 14

5.8 Settings menu: Selection temperature sensor ...........................................................page 15

5.9 Settings menu: Calibrate thermostat/external sensor .............................................page 15

5.10 Settings menu: ECO fan function ..................................................................................page 16

5.11 Settings menu: Self Learning Heating ...........................................................................page 17

5.12 Settings menu: Change language ...................................................................................page 17

5.13 Settings menu: Switch on/off Summer/Winter time ................................................page 18

5.14 Settings menu: Info .......................................................................................................... page 18

5.15 Settings menu: Change pin code ...................................................................................page 19

5.16 Settings menu: Call Factory menu ................................................................................page 19

5.17 Settings menu: Call Installer menu ................................................................................page 19

5.18 Recover factory settings .................................................................................................page 20

6.0 Messages and Malfunctions

6.1 Message ............................................................................................................................page. 21

6.2 Malfunction messages ......................................................................................................page 21

7.0 Disposal of the OptiTherm+ ............................................................................................. page 22

Figures / Tables

[1] Table of cable diameters and max. length of cabling ................................................page 135

[2] Overview - connecting thermostat ..............................................................................page 135

[3] Connecting OptiTerm to one or more air heaters .................................................. page 136

[4] Correctly addressing OptiTherm+ ..............................................................................page 137

[5] Setting dip switches and S4 air heater switch ...........................................................page 137

Quick start ...........................................................................................................................................page139

2

Read this document before

installing the appliance

Warning

Incorrect installation, adjustment, alteration, repair or maintenance may lead to material

damage or injury. All work must be carried out by approved, qualied professional. If the

appliance is not positioned in accordance with the instructions, the warranty shall be rendered

void. This appliance is not intended for use by people (including children) who suffer from a

physical, sensory or mental handicap, or who are inadequately knowledgeable or experienced,

unless they are supervised or have received instruction in the use of the appliance from a

person who is responsible for their safety. Children must be supervised to ensure that they do

not play with the appliance.

If in this technical book there is a reference to an image or table, then a gure is stated between

square brackets , for example [3]. The number refers to the images and tables with the number

stated in this technical book.

1.0 General

1.1. Subject to change

The manufacturer has a policy of continuous product improvement and reserves the right to

make changes to the specications without prior notice. The technical details are considered

correct but do not form the basis for a contract or warranty. All orders are accepted subject to

the standard terms and conditions of sale and delivery (which will be sent to you at your request).

1.2 General warnings

Installation must comply with the relevant local and/or national regulations. Therefore allow

the OptiTherm+ to be installed by a professionally competent and qualied electrician taking

account of the national and international regulations. Faulty installation, adjustment, alteration,

maintenance activity or repair shall render the warranty void.

1.3 Type of thermostat and application

The OptiTherm+ is a digital clock thermostat with internal room sensor with which 1 or more

air heaters (type GS+ or G+), up to a maximum of 8, can be controlled on the basis of the room

temperature by means of a bus system.

The OptiTherm+ provides:

•

The possibility of switching on/off the heating mode.

•

The possibility of switching off/off the ventilator of the air heater(s).

•

The possibility to signal and to rectify malfunctions

•

A year clock with 20 program blocks

•

The possibility to program exception days on date.

•

The possibility to regulate between 4 different methods of operation

(DAY, ECO, NIGHT, FROST).

•

An overtime timer for switching to a different operating mode outside the switching times.

•

Pin code protection to protect settings such as temperature, clock program, etc.

3

EN

•

A frost protection which automatically switches on the air heaters when the temperature

falls too low.

2.0 Technical data

2.1 Technical data

•

Type designation : OptiTherm+

•

Type of thermostat : Digital clock thermostat

•

Item number : 06 29 189

•

Connection : Bus system (2 Wires)

•

cabling : Protected bus cable, see also §3.3

•

Dimensions : 129 x 129 x 20mm (lxwxh)

•

Weight : 188 grammes

•

Protection class : IP30

•

Ambient temperature : 0 - 40º

•

Temperature setting : 0 to 40º, in increments of 0.5º

•

Clock program : 20 program blocks

Mon-Fri , Tues-Fri, Sat-Sun, daily or per day

•

Exception days : 20 program blocks

Switch to day, ECO or night temperature

•

overtime timer : Free setting range from 15 mins - 24 hrs

Switch to day, ECO or night temperature

•

Calibrate temperature sensor : setting range from -3.0º to 3.0º

•

Room sensor : standard provision

•

External sensor : option of measuring the temperature per unit or on the

basis of an average value.

•

Time display : 24 hours

•

Summer / winter time : Adjustable automatic/off

•

Languages : Dutch, English, German, French, Polish, Romanian

4

2.2 Factory settings

•

Temperature : Day 18°C

ECO 15°C

Night 08°C

Frost 05°C

•

Clock program : Program block 1

Day 12345

Switch time 08:00 >> 17:00

Switch to Day

•

Exception day : off

•

overtime timer : Maximum setting time 03:00hrs

Switch to Day

•

Selection temperature sensor : Sensor Thermostat

•

Calibrate temperature sensor : 0.0°C

•

Summer / winter time : Automatic

•

Pin code : 1 0 0 0

3.0 Installation and initial starting

3.1 General

•

After unpacking check the OptiTherm+ and if also ordered, the external sensor(s) delivered

with it for damage.

•

At the same time check the correctness of the type/model

(Thermostat: OptiTherm+ 06 29 189, external sensor: Digital sensor conc. 2 Wires 06 29

194).

Contact the supplier if the thermostat is damaged or it is not the correct type/model.

3.2 Positioning

In order to determine an appropriate place to mount the OptiTherm+ you must consider the

points below:

– Place the OptiTherm+ in the room to be heated, because it is supplied with an internal room

sensor. This is not applicable when an external sensor (optional deliverable) connected to the air

heater(s).

– Mount the OptiTherm+ in a draft free location

– Do not mount the OptiTherm+ on a cold wall/partition.

– Do not mount the OptiTherm+ directly in the airow of the air heater(s).

– It is advised to place the OptiTherm+ at a distance of ±1.5m from the oor.

3.3 Cabling

For the cabling a protected bus cable must always be applied.

Also see table [2] for the maximum length and the proper diameter.

Attention!

The cable protection is earthed on the air heater.

5

EN

The bus cable must be selected according to the country specic rules, where the values which

are included in the technical data must be adhered to.

Cable type Application EIB specication

YCYM Fixed system Dry, damp, wet rooms

In the open air (no direct exposure to

sunlight)

Face-t, ush-t, in conduits

J-Y(st)Y Fixed system Only in interior spaces

Face-t, in conduits

JH(st)H Halogen-free cables,

Remote system

A-2Y(L)2Y

A-2YF(L)2Y

Telephone ground cable,

System in outside area

3.4 Mounting and installation

For the correct mounting and connection of the OptiTherm+ to the air heaters, you follow the

points below:

•

Check that the electricity supply is switched off. If that is not the case, then rst switch off

the electricity supply before you proceed. For this, also consult the technical manual of the

air heater to be connected.

•

Mount the OptiTherm+ on the partition, taking into account §3.2 Placing the OptiTherm+

•

Only applicable when external sensors are applied:

Mount the external sensors at the correct place. For this, also consult the instruction which

is delivered with the sensor.

•

Lay the correct cabling between the air heater and the OptiTherm+ and, if applicable, the air

heaters with each other. For this also take into account §3.3 Cabling. [2][3]

•

Only applicable when external sensors are applied:

Lay the correct cabling between the air heater and the external sensor. For this also take

into account §3.3 Cabling and the instructions for the external sensor. [2][4]

•

Connect the OptiTherm+ and the air heater(s) according to the diagram [2][3]

•

Only applicable when external sensors are applied:

Connect the cable to the external sensor and the air heater and there also take into account

the instructions for the external sensor. [2][4]

•

Only applicable with the connection of more than one appliance on 1 OptiTherm+:

Install the Dip switch and switch S4 on the automatic burner of the air heaters. For this,

ensure that the air heater to which the OptiTherm+ is connected is always addressed as

appliance 1. [5][6]

When you are ready with the installation and connection, you can start to operate the

OptiTherm+ and the air heater(s). For this, also consult the technical manual of the air heater.

6

3.5 First initial operation

•

Connect the electricity supply again once the mounting and installation of the OptiTherm+

and air heaters has been completed. For this, also consult the technical manual of the air

heaters.

After you have connected the electricity supply the OptiTherm+ display will light up and ask you:

1. To select the correct language.

2. To enter the correct data and time.

For this, follow the image below:

OK

modify

OK

to next digit

Language

Nederlands

Deutsch

Français

English

Date/Time

Date

Time

--201101 03

08:00

5.0 °C

01-03-2011

08:30

0.21

modify

•

Select with the  and  button, the desired language and conrm this with the OK button.

•

The display now automatically jumps to the date setting. Now change the day, month and

year, in that order with the  and  button. Conrm each entry with the OK button after

which the display automatically goes to the following entry. After you have changed the

year, the display will automatically go to the time settings.

•

Now change the hours and minutes, in that order with the  and  button. Conrm each

entry with the OK button after which the display goes automatically to the following entry.

•

After the minutes are lled in the main screen will be shown on the display and the

OptiTherm+ is ready for use.

For further explanation see the sequence of this technical manual.

– For the operation and explanation of the display and the buttons, see §4.0 Operation.

– For changing the settings see §5.0.

– For the Messages and Malfunctions see §6.0.

7

EN

4.0 Operation

B

C

A

G

H

I

J

KF

E

D

12.0

08:00

01-03-2011

18.0 °C

RESETESC

OK

4.1 Explanation of buttons

A - Display

B - Red led i

Lights up when there is a Malfunction Message.

C - Info push-button (blue)

With this the actual (Malfunction) Messages can be passed through from the air heaters.

D - Push-button for switching the heating mode on and off.

E - Push-button for switching the ventilator on and off.

F - Push-button for switching the overtime timer on and off.

Every push increases the time by 15 mins.

You switch the timer off again by keeping the push-button pressed in.

G - No function

H - ESC Push-button

Menu or item left without executing changes

I - RESET Push-button

Reset a Malfunction

J - OK Push-button

Conrm a choice or proceed in order to change the next gure.

K -  (up) and  (down) buttons

The menu proceeds if a setting is increased or decreased.

8

4.2 Explanation of display and symbols.

B

C

A

D

E

06 29 189

OptiTherm+

12.0

08:00

01-03-2011

18.0 °C

00:15

F

H

I

P

O

N

M

K

L

01:00

J

Display

A - Shows the measured room temperature.

B - Displays the desired room temperature.

Displays the mode of operation (DAY, NIGHT, ECO, FROST PROTECTION)

C - Indicates which functional mode is switched on (HEATING, VENTILATION),

if there is a heating request and of the Message

⦻

(clip 1 and 2 on the air heater

disconnected) is active.

D - Reason for the mode of operation.

(clock switch, overtime timer or exception day)

E - Shows the actual date and time

Symbols

F - Heating mode switched on symbol

H - Ventilator switched on symbol

I or II indicates if the ventilator is in high or low position (if applicable).

I - Message OFF (clip 1 and 2 on equipment disconnected)

J - Clock switch active symbol

K - overtime timer active symbol

(running time indicates when this function will be switched off again)

L - Exception day active symbol

M - Day temperature symbol (factory setting 18 °C)

N - Night temperature symbol (factory setting 15 °C)

O - ECO temperature symbol (factory setting 8 °C)

P - Frost protection symbol (factory setting 5 °C)

9

EN

4.3 Frost protection

The OptiTherm+ is supplied with a frost protection function. This means that when the room

temperature falls below the set frost temperature, the air heater(s) are automatically switched on.

That is also the case when the heating mode is not switched on. The frost temperature is set as

standard at 5°C, you can change that, if you wish, for that see §5.2 change temperature setting.

04.0

08:00

01-03-2011

05.0 °C05.0 °C

01-03-2011

08:00

0.90

4.4 Switch heating mode on/off.

To switch the heating mode on or off, you push the button “heating”.

12.0

17:00

01-03-2011

18.0 °C05.0 °C

01-03-2011

08:00

0.21

The ame symbol will now appear on the display so that you can see that the heating mode is

switched on. With heating request, the status bar will also appear on the display.

4.5 Switch ventilation mode on/off.

To switch the ventilator of the air heater on or off, you push the button “ventilation”.

21.0

08:00

01-03-2011

05.0 °C05.0 °C

01-03-2011

08:00

0.21

The ventilator symbol will now appear with I or II on the display so that you can see that the

ventilator is switched on.

Note!

The ventilation mode can be used at the same time as the heating mode. So if you wish during

heating mode you can have the ventilator running continuously.

4.6 Switch overtime timer on/off

When you want to switch to another operation mode outside the program switch times you can

make use of the overtime timer. See the image below:

16.0

17:00

01-03-2011

18.0 °C

00:15

16.0

01-03-2011

15.0 °C

17:00

hold

± 3sec.

1x = 00:15

2x = 00:30

3x = 00:45

enz...

– Switch on overtime timer : press in button or increase the time duration.

Every time this button is pushed in, the time duration is increased by 15 mins.

– Switch off overtime timer : keep

button pushed in until the symbol and the

time remaining disappear from the screen

As standard, the overtime timer will switch the OptiTherm+ to the day temperature The

maximum time duration is 3:00 hrs. The settings can be changed in the settings menu: §5.7

overtime timer

10

EN

11

5.0 Change settings

5.1 Call user menu

To activate the users menu:

•

You push the OK button.

•

After which you enter the correct Pin code according to the image below

(standard factory setting is 1000).

selectmodify

User Menu

Clock Program

Special day

Settings

Temperature

OK

ES

CE

SC

2x

OK

factory default

menu code

1 0 0 0

User Menu

18.0 °C

01-03-2011

08:10

0.21

Code 0000

OK

na 4x

to next digit

•

with the  and  button you change the ashing gure.

•

you conrm this with the OK button and you jump to the next gure. After you push on

the OK button at the 4th gure and you enter the correct pin code, you enter the user

menu and you can change the temperature setting, the switch times, the exception days and

all the other settings.

When an incorrect pin code is entered the screen image pin code input remains visible and the

code jumps back to 0000.

Note!

When no button is pressed for the duration of 1 minute the OptiTherm+ display will

automatically leave the menu and go back to the main display.

5.2 User menu: change the temperature setting

To change the temperature setting you follow the images below:

User Menu

Clock Program

Special day

Settings

Temperature

OK OK

ESC ESCESC

back to main screen

selectmodify

Temperature

Eco

Night

Frost

Day

5.0 °C

8,0 °C

15,0 °C

18,0 °C

Temperature

Eco

Night

Frost

Day

5.0°C

8,0°C

15,0°C

18,0°C

select

•

In the user menu select the menu-item temperature and then push the OK push-button.

•

With the  and  button, select the mode of operation which you wish to change and

conrm this with the OK button.

•

The display jumps to the temperature setting of the chosen mode of operation. With

the  and  button, change the temperature setting and conrm this with the OK button.

Follow the steps above to change the other temperature settings.

When you are nished with changing the temperature settings:

•

After the last change you press the OK button to conrm this.

•

Then you push the ESC button to go back to the user menu again.

12

5.3 User menu: change/set the clock program

To adjust the existing clock program or to enter new times:

•

You select the menu item clock program and then you push the OK button.

•

Now change the existing clock program or input a new clock program following the images

below:

Clock Program

Date

Interval

Switch to

Program

12345

08:00 >> 17:00

Day

1

Clock Program

Date

Interval

Switch to

Program

12345

08:00 >> 17:00

Day

1

OK OK

ES

CE

SCESC

select select modify

User Menu

Clock Program

Special day

Settings

Temperature

back to main screen

•

Now with the  and  button, you select the menu-item program and then push the OK

button

•

With the  and  button, select a new or existing program block (1 to 20) and then push

the OK button.

•

Now with the  and  button, you select Day and then push the OK button

•

Now with the  and  button, you change to the desired days and then push the OK

button again.

(12345, 1234567, 1, 2, 3, 4, 5, 6, 7, 67, 2345 or off).

1=Monday, 2=Tuesday, 3=Wednesday, ……, 6=Saturday, 7=Sunday

•

Now with the  and  button, you select the switch time program and then push the OK

button

•

now with the  and  button you change the hours and minutes from the start and end

times, in that order. Conrm each entry with the OK button after which the display goes

automatically to the following entry. After you conrm the last entry you automatically go

back to the menu-item clock program

•

Now with the  and  button, you select switch to and then push the OK button.

•

Now with the  and  button you change the desired mode of operation (DAY,

NIGHT, ECO) and then push the OK button.

Repeat the above to input a new clock program or another change.

When you are nished with changing the clock program:

•

You push the ESC button to go back to the user menu again.

5.4 User menu: change/set exception day

Exception days can be used to allow the OptiTherm+ to switch to another mode of operation

on a certain date. After the exception day has passed then it automatically disappears from the

program and it is again available for the entry of a new one. You have 20 program blocks available

for input.

To program or to change an exception day:

•

With the  and  button, you select the menu-item exception day and then push the OK

button

EN

13

Now change the existing exception days or input new exception days following the images below:

OK OK

ESC ESCESC

select selectmodify

Special day

Date

Interval

Switch to

Program

Off

___:___ >> ___:___

___

1

Special day

Date

Interval

Switch to

Program

Off

___:___ >> ___:___

___

1

back to main scree

n

User Menu

Clock Program

Special day

Settings

Temperature

•

With the  and  button, you select program and then push the OK button

•

Chose a new or existing program block (1 to 20). And conrm this with the OK button.

•

Now with the  and  button, select the desired date and conrm this with the OK

button. Change the date or enter a new date (day-month-year) by changing the day, month

and year, in that order with the  and  button. Conrm each entry with the OK button

after which the display goes automatically to the following entry. After you have changed the

year, the display will automatically go to the time settings.

•

Now with the  and  button select the switch time and with the  and  button

change the hours and minutes of the start and end time, in that order. Conrm each entry

with the OK button after which the display goes automatically to the following entry. After

you conrm the last entry you automatically go back to the menu-item Switch time

•

Now with  and  button select switch to and change the desired mode of operation in

DAY, NIGHT or ECO.

•

Conrm this by then pushing the OK button again

•

Repeat the above to enter a new exception day or to change an existing one.

•

Push the ESC button to go back to the main display.

5.5 User menu: call settings menu

In the settings menu you can make more extensive setting changes such as, among other things,

the date/time, the maximum duration of the Overtime timer, the language and the pin code.

To enter the settings menu:

•

With the  and  button, you select the menu-item settings and then push the OK button

You are now in the menu settings and can now select various settings to change.

User Menu

Clock Program

Special day

Settings

Temperature

OK

ESCESC

selec

ts

elect

Settings

Overtime setting

Select Temperature sensor

Calibrate

Date/Time

ECO fan function

back to main screen

The settings which you can change

are:

- Date/Time

- Overtime timer

- Selection temperature sensor

- Calibrate thermostat

- ECO fan function

- Self Learning Heating

- Language

- Summer / winter time

- Info

- Pin code

- Factory menu

- Installer menu

14

5.6 Settings menu: Change date/time

To adjust the date/time you follow the images below:

OK OK

ES

CE

SCESC

selectselect modify

Settings

Overtime setting

Select Temperature sensor

Calibrate

Date/Time

ECO fan function

2x

Date/Time

Time

Date 01 -03 2011-

:08 00

Date/Time

Date

Time

--201101 03

08:00

OK

to next digit

back to main screen

•

With the  and  button, select the menu-item Date/time in the menu settings and then

push the OK button.

•

Now select the date by pushing the OK button.

•

Change the date with the  and  button and conrm each input with the OK button

after which the display automatically goes to the next entry. After you have changed the

year, the display will automatically go back to the Date.

•

Now with the  and  button, select Time

•

Now with the  and  button, select Time and then push the OK button. With the  and

 button change the hours and minutes and conrm each entry with the OK button, after

which the display automatically goes to the next entry. After you conrm the last entry you

automatically go back to the Time.

•

When you have nished the changes and these are conrmed with the OK button, you push

the ESC button to go back to the settings menu.

•

Now select another item to change or to go back to the user menu by pushing the ESC

button. Push the ESC button again to go back to the main display.

5.7 Settings menu: Change overtime timer settings

To change the overtime timer settings you follow the image below:

OK OK

ESC ESCESC

select select modify

Settings

2x

OK

to next digit

Overtime setting

Switch to

Max time setting

Day

Overtime setting

Switch to

Max time setting

Day

01 :00 01 :00

back to main screen

Overtime setting

Select Temperature sensor

Calibrate

Date/Time

ECO fan function

•

With the  and  button, select the menu-item Overtime timer in the menu settings and

then push the OK button.

•

Now the maximum time duration of the overtime timer and to which mode of operation

the OptiTherm+ must be switched, can be changed using the overtime timer.

•

s elect the maximum setting time and then push the OK button.

•

With the  and  button, change the maximum time (minimum increasing or decreasing is

15 minutes). And then push the OK button.

EN

15

•

With the  and  button Switch to, to change the mode of operation, and then push the

OK button.

•

With the  and  button, change the mode of operation in DAY, NIGHT or ECO and

conrm this by pushing the OK button.

•

When you have nished the changes and these are conrmed with the OK button, you push

the ESC button to go back to the settings menu.

•

Now select another item to change or to go back to the user menu by pushing the ESC

button. Push the ESC button again to go back to the main display.

5.8 Settings menu: Selection temperature sensor

With the OptiTherm+ you have the possibility to measure the room temperature by:

1. Thermostat: sensor built-in to OptiTherm+ itself

2. External zone: an external sensor connected to each air heater.

3. External average: an external sensor connected on one or more air heaters. Where the

average value is automatically calculated based on the number of connected sensors.

As standard, the temperature sensor on the OptiTherm+ is used.

When use is made of 1 or more external sensors, you must indicate this in the settings menu

Change selection temperature sensor. See the image below:

OK OK

ESC ESCESC

select select modify

Settings

ECO fan function

2x

Select Temperature sensor

Sensor Room Control

Select Temperature sensor

Sensor Room ControlDate/Time

Overtime setting

Select Temperature sensor

Calibrate

back to main screen

To adjust this:

•

Select the menu-item Selection temperature sensor and then push the OK button.

•

Select the sensor by pushing the OK button.

•

Change the setting and then push the OK button.

You can choose from the thermostat (OptiTherm+ sensor), external zone (each air heater one

own external sensor) or external average (1 or more sensors).

•

When you have nished with the changes you leave the menu item by pressing the ESC

button and you go back to the settings menu.

•

Now select another item to change or to go back to the user menu by pushing the ESC

button. Push the ESC button again to go back to the main display.

5.9 Settings menu: Calibrate thermostat/external sensor

When because of unfavourable circumstances there is a deviation in the displayed measured room

temperature and the actual room temperature, you can adjust this deviation by calibrating the

OptiTherm+. Always ensure that the thermostat or external sensor is properly mounted and

connected.

For example:

The measured temperature is 18°C, the screen display on the OptiTherm+ shows 20°C. The

difference in this example is therefore 2°C too high  the correction value must then be set at

-2°C.

16

You can change this following the image below:

OK OK

ESC ESCESC

select select modify

ECO fan function

2x

OK

to next digit

Calibrate

Deviation

Sensor

0.0 K

Room Control

Calibrate

Deviation

Sensor

0.0 K

Room Control

back to main screen

Settings

Calibrate

Date/Time

Overtime setting

Select Temperature sensor

•

Now with the  and  button, select Calibrate Thermostat and then push the OK button

•

Only applicable when an external sensor is also used.

•

With the  and  button, select Sensor and then push the OK button

•

Only applicable when an external sensor is also used.

•

Now with the  and  button select the air heater (1 to 8) from where the external

sensor must be calibrated and then push the OK button.

•

With the  and  button, select Deviation and then push the OK button

•

With the  and  button set the desired value and conrm this with the OK button.

•

When you have nished with the changes you leave the menu item by pressing the ESC

button and you go back to the settings menu.

•

Now select another item to change or to go back to the user menu by pushing the ESC

button. Push the ESC button again to go back to the main display.

5.10 Settings menu: ECO fan function

With the ECO fan function it is possible to turn on the fan of the unit when the temperature near

the unit is higher than that of the OptiTherm+ or, if applicable, the external sensor. With this

function it can be prevented that the warm air stays at the top of the room.

To turn on the fans in this function, all of the following requirements need to be met:

• There must have been a burner demand in the past 24 hours

• The temperature near the unit must be higher than: setpoint+1K,setpoint+2 – setpoint+ 5K

(depending on the settings)

• The temperature difference measured at the OptiTherm+ and near the unit, must be greater

than 0,0 – 10,0K (depending on the settings)

You can change the settings of the ECO fan function following the image below:

•

OK OK

ESC ESCESC

back to main screen

select modify

Settings

Overtime setting

Select temperature sensor

Calibrate

ECO fan function

2x

ECO fan function

Ecofan Setpoint

Function

Setpoint + 1K

On

ECO fan function

Self Learning Heating

Delta T

3.0 K

Ecofan Setpoint

Function

Setpoint + 1K

On

Delta T

3.0 K

select

Select the menu-item ECO fan function and then push the OK button.

• Select Function to turn the ECO fan function on or off.

•

With the  and  button, select the required setting and then push the OK button.

EN

17

• Select the Ecofan Setpoint to set the temperature, near the unit, at which the fans may turn

on.

• With the  and  button, select the required setting and then push the OK button.

• Delta T sets the minimum temperature between near the unit and at the OptiTherm+.

• With the  and  button, select the required setting and then push the OK button.

•

When you have nished with the changes you leave the menu item by pressing the ESC

button and you go back to the settings menu.

•

Now select another item to change or to go back to the user menu by pushing the ESC

button. Push the ESC button again to go back to the main display.

5.11 Settings menu: Self Learning Heating

The Self Learning Heating function optimalizes the turn-on time of the units. In the Clock program

function it must be indicated when a certain temperature is desired. The OptiTherm+ then

decides when the unit must turn on to realise this temperature. It uses the history of the past

days to do this. This function is turned off as standard. To turn on this function, see the image

below:

•

OK OK

ESC ESCESC

back to main screen

select select modify

Settings

Select Temperature sensor

Calibrate

ECO fan function

2x

Self Learning Heating

Function Off

Self Learning Heating

Function Off

Language

Select the menu-item Self Learning Heating and then push the OK button.

• Select Function to turn Self Learning Heating on or off.

•

With the  and  button, select the required setting and then push the OK button.

•

When you have nished with the changes you leave the menu item by pressing the ESC

button and you go back to the settings menu.

•

Now select another item to change or to go back to the user menu by pushing the ESC

button. Push the ESC button again to go back to the main display.

5.12 Settings menu: Change language

If you want to change the chosen language you can change this by going to the settings menu and

changing the language.

To change the chosen language you follow the image below:

OK

ESCESC

back to main screen

select select

Settings

ECO fan function

Self Learning Heating

Language

Calibrate

Summer/wintertime

2x

Language

Nederlands

Deutsch

Français

English

OK

conrm selection

18

• With the  and  button, select Language and then push the OK button

•

With the  and  button, select the desired language and conrm this with the OK

button. In the middle of the top of the screen the chosen language is shown and the display

also appears in that language.

•

When you have nished with the changes you leave the menu item by pressing the ESC

button and you go back to the settings menu.

•

Now select another item to change or to go back to the user menu by pushing the ESC

button. Push the ESC button again to go back to the main display.

5.13 Settings menu: Switch on/off Summer / winter time

The OptiTherm+ has an automatic summer/wintertime conversion. When this is not desired, it

can be switched off here.

Follow the image below to change it:

OK OK

ESC ESCESC

back to main screen

select select modify

Setting

Self Learning Heating

Language

Summer/wintertime

ECO fan function

Information

2x

Summer/wintertime

State Automatic

Summer/wintertime

StateAutomatic

•

In the settings menu select Summer/winter time and then push the OK button.

•

Select status by pushing the OK button

•

With the  and  button, change the setting on/off and conrm this with the OK button.

•

Quit summer/winter time by pushing the ESC button The display now goes back to the

settings menu.

•

Now select another item to change or go back to the user menu by pushing the ESC

button. Push the ESC button again to go back to the main display.

5.14 Settings menu: Info

In this menu-item you can read the software version.

OK

ESCESC

select

Setting

Language

Summer/wintertime

Information

Self Learning Heating

2x

Information

Software version 1.0 [xxxxxxxx]

back to main screen

•

In the settings menu select Info and then push the OK button. The info data is now shown

on the screen.

•

Quit Info by pushing the ESC button. The display now goes back to the settings menu.

•

Now select another item to change or go back to the user menu by pushing the ESC

button. Push the ESC button again to go back to the main display.

EN

19

5.15 Settings menu: Change pin code

The OptiTherm+ is provisioned with a security pin code as standard. This is set as 1000. If

desired, you can change this to another Pin code.

Follow the image below to change the Pin code:

OK OK

ESCESC

back to main screen

selec

tm

odify

Settings

Summer/wintertime

Information

PiIN

Language

Factory menu

2x

Code

New PIN

0000

OK

to next digit

4x

•

In the settings menu select Pin code and then push the OK button.

•

With the  and  button, change the rst gure and conrm this by pushing the OK

button, the display automatically jumps to the next gure. Change all desired gures in that

way. After the 4th gure the display automatically goes back to the settings menu.

•

Now select another item to change or go back to the user menu by pushing the ESC

button. Push the ESC button again to go back to the main display.

5.16 Settings menu: Call Factory menu

This menu is only accessible with a special code, provided only to qualied persons.

5.17 Settings menu: Call Installer menu

Menu only accessible for well trained installers. Do not change settings injudiciously.

Pin code: 5050

To call the Installer menu you follow the image below:

OK OK

ESCESC

back to main screen

select select

Settings

Information

Installer menu

Summer/wintertime

2x

Installer menu

Code 0000 Control On/Off

Installer menu

to next digit

OK

ESC

factory default

Installer menu code

5 0 5 0

Factory menu

•

In the settings menu select Installer menu and then push the OK button.

•

Now enter the Pin code for the Installer menu. With the  and  button, change the rst

gure and conrm this by pushing the OK button, the display automatically jumps to the

next gure. Change all desired gures in that way. After the 4th gure, when the pin code

has been correctly entered, the service menu is displayed on the screen.

20

Burner check

Possibility of checking the ionizing current of the of the unit concerned.

Self learning heating

To read out the Self Learning Heating.

Possibility to manually set the Self Learning Heating to a xed value.

Possiblity to set the minimum time of which the unit must be in operation during the heating

curve.

Room Controller

Setting P band

Setting I time

Hysteresis UP: maximum temperature exceedance of the desired temperature at which the unit

stays in operation.

Hysteresis DOWN: maximum temperature deviation lower than the desired temperature, at

which the unit must come back into operation.

Supply temp max: maximum supply temperature of the unit

Supply temp min: minimum supply temperature of the unit

5.18 Recover factory settings

When you execute this function all settings in the OptiTherm+ are reset to the factory settings

§2.2. This function can be executed at any time. Follow the image below to execute this function:

OK

select

to next digit

OK

modify

Date/Time

Time

Date 01 -03 2011-

:08 00

18.0 °C

01-03-2011

09:00

0.51

Language

Nederlands

Deutsch

Français

English

18.0 °C

01-03-2011

09:00

0.51

ESC OK

Reset

RESTORE

FACTORY DEFAULT

OK-CONTINUE

ESC-BACK

ESC

OK

±12sec.

•

Keep pushing the ESC button and the OK button simultaneously for +/- 12 seconds until

the text ‘Factory Settings’ is displayed on the screen.

•

Only applicable when you wish to recover the factory settings

To execute, press the OK button. The factory values are recovered and the language, date

and time must be entered again. For this, also see §3.5 First Initial Operation

•

Only applicable when you do not wish to recover the factory settings

Press the ESC button to quit the function again.

The main display is shown again and the factory values are not reset.

La page charge ...

Mark OptiTherm Plus 06 29 189 Technical Manual

Mark OptiTherm Plus 06 29 189 Technical Manual

dans d''autres langues

Documents connexes

Autres documents