Kenwood KDC-BT23 Le manuel du propriétaire

Data Size: B6L (182 mm x 128 mm)

Book Size: B6L (182 mm x 128 mm)

For your records

Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided below. Refer to the model and serial

numbers whenever you call upon your Kenwood dealer for information or service on the product.

Model KDC-X303/KDC-BT375U/KDC-BT350U/KDC-BT33/KDC-BT275U/KDC-BT23/KDC-MP375BT/KMR-D375BT

Serial number

US Residents Only

Register Online

Register your Kenwood product at http://www.kenwood.com/usa/

KDC-X303

KDC-BT375U

KDC-BT350U

CD-RECEIVER

INSTRUCTION MANUAL

AMPLI-TUNER LECTEUR DE CD

MODE D’EMPLOI

REPRODUCTOR DE DISCOS COMPACTOS RECEPTOR DE FM/AM

MANUAL DE INSTRUCCIONES

KDC-BT33

KDC-BT275U

KDC-BT23

KDC-MP375BT

KMR-D375BT

JS_KWD_KDC_X303_KN_C20.indd 1JS_KWD_KDC_X303_KN_C20.indd 1 9/7/2018 10:21:30 AM9/7/2018 10:21:30 AM

Data Size: B6L (182 mm x 128 mm)

Book Size: B6L (182 mm x 128 mm)

i

CAUTION

Use of controls or adjustments or performance of procedures other than those specified herein may

result in hazardous radiation exposure.

In compliance with Federal Regulations, following are reproductions of labels on, or inside the product

relating to laser product safety.

JVC KENWOOD Corporation

2967-3, ISHIKAWA-MACHI,

HACHIOJI-SHI, TOKYO, JAPAN

THIS PRODUCT COMPLIES WITH DHHS RULES 21CFR

SUBCHAPTER J IN EFFECT AT DATE OF MANUFACTURE.

Location : Top Plate

FCC WARNING

This equipment may generate or use radio frequency energy. Changes or modifications to this

equipment may cause harmful interference unless the modifications are expressly approved in the

instruction manual. The user could lose the authority to operate this equipment if an unauthorized

change or modification is made.

FCC NOTE

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment may cause harmful interference to

radio communications, if it is not installed and used in accordance with the instructions. However,

there is no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV technician for help.

CALIFORNIA, USA ONLY

This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material—special

handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate

Información acerca de la eliminación de equipos eléctricos y electrónicos al final de la vida

útil (aplicable a los países que hayan adoptado sistemas independientes de recogida de

residuos)

Los productos con el símbolo de un contenedor con ruedas tachado no podrán ser

desechados como residuos domésticos. Los equipos eléctricos y electrónicos al final

de la vida útil, deberán ser reciclados en instalaciones que puedan dar el tratamiento

adecuado a estos productos y a sus subproductos residuales correspondientes.

Póngase en contacto con su administración local para obtener información sobre el

punto de recogida más cercano. Un tratamiento correcto del reciclaje y la eliminación

de residuos ayuda a conservar los recursos y evita al mismo tiempo efectos

perjudiciales en la salud y el medio ambiente.

Informação sobre a eliminação de pilhas

Este produto não deve ser eliminado como lixo doméstico geral. Devolva a pilha usada ao revendedor ou

entidade autorizada para que a mesma seja devolvida ao fabricante ou importador.

A reciclagem e a eliminação de lixo de maneira apropriada ajudarão a conservar os recursos naturais ao

mesmo tempo que prevenirão os efeitos prejudicais à nossa saúde e ao meio ambiente.

Supplier's Declaration of Conformity

Trade Name: KENWOOD

Products: CD RECEIVER

Model Name: KDC-X303/KDC-BT375U/KDC-BT350U/KDC-BT33/KDC-BT275U/

KDC-BT23/KDC-MP375BT/KMR-D375BT

Responsible Party: JVCKENWOOD USA CORPORATION

2201 East Dominguez Street, Long Beach, CA 90810, U.S.A.

PHONE: 310 639-9000

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING

TWO CONDITIONS:

(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND

(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY

CAUSE UNDESIRED OPERATION.

JS_KWD_KDC_X303_KN_C.indd iJS_KWD_KDC_X303_KN_C.indd i 4/6/2018 11:26:21 AM4/6/2018 11:26:21 AM

Data Size: B6L (182 mm x 128 mm)

Book Size: B6L (182 mm x 128 mm)

ii

CAUTION

This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled

environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the IC radio

frequency (RF) Exposure rules. This equipment has very low levels of RF energy that it deemed to

comply without maximum permissive exposure evaluation (MPE). But it is desirable that it should be

installed and operated keeping the radiator at least 20 cm or more away from person’s body.

ATTENTION

Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un

environnement non contrôlé et respecte les règles les radioélectriques (RF) de la FCC lignes directrices

d’exposition et d’exposition aux fréquences radioélectriques (RF) CNR-102 de l’IC. Cet équipement émet

une énergie RF très faible qui est considérée comme conforme sans évaluation de l’exposition maximale

autorisée (MPE). Cependant, il est souhaitable qu’il devrait être installé et utilisé en gardant une

distance de 20 cm ou plus entre le radiateur et le corps humain.

IC (Industry Canada) Notice

This device complies with Industry Canada’s licence-exempt RSSs.

Operation is subject to the following two conditions:

(1) This device may not cause interference; and

(2) This device must accept any interference, including interference that may cause undesired

operation of the device.

Note de IC (Industrie Canada)

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts

de licence.

L’exploitation est autorisée aux deux conditions suivantes:

(1) l’appareil ne doit pas produire de brouillage;

(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage

est susceptible d’en compromettre le fonctionnement.

Para cumplimiento de la IFT:

“La operación de este equipo está sujeta a las siguientes dos condiciones:

(1) es posible que este equipo o dispositivo no cause interferencia perjudicial y

(2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su

operación no deseada”

Contains Bluetooth Module FCC ID: ZWY8811X

IC ID: 12033A-8811X

This transmitter must not be co-located or operated in conjunction with any other antenna or

transmitter.

JS_KWD_KDC_X303_KN_C.indd iiJS_KWD_KDC_X303_KN_C.indd ii 4/6/2018 11:26:21 AM4/6/2018 11:26:21 AM

Data Size: B6L (182 mm x 128 mm)

Book Size: B6L (182 mm x 128 mm)

iii

SOFTWARE LICENSE AGREEMENT

The software embedded in the Product (hereinafter the "Licensed Software") provided by Licensor is

copyrighted to or sublicensable by the Licensor, and this Agreement provides for the terms and conditions

which Users shall follow in order to use the Licensed Software.

The User shall use the Licensed Software by agreeing with the terms of this Software License Agreement.

This Agreement shall be deemed completed at the time the User (hereinafter the "User") initially used the

Product in which the "Licensed Software" is embedded.

The Licensed Software may include the software which has been licensed to the Licensor directly or

indirectly from any third party. In such case, some third parties require the Users to follow their conditions

for use separately from this Software License Agreement. Such software shall not be subject to this

Agreement, and the Users are urged to read the "Important Notice concerning the Software" to be provided

separately below.

Article 1 General Provision

The Licensor shall grant to the User a non-exclusive and non-transferable (other than the exceptional case

referred to in Article 3, Paragraph 1) licensed to use the Licensed Software within the country of the User.

(the country where the User bought the Product (hereinafter the "Country")

Article 2 License

1. The license granted under this Agreement shall be the right to use the Licensed Software in the

Product.

2. The User shall not duplicate, copy, modify, add, translate or otherwise alter, or lease the Licensed

Software and any related documents, whether in whole or in part.

3. The use of the Licensed Software shall be limited to personal purpose, and the Licensed Software shall

not be distributed, licensed or sub-licensed whether it is for commercial purpose or not.

4. The User shall use the Licensed Software according to the directions described in the operation

manual or help file, and is prohibited to use or duplicate any data in a manner violating the Copyright

Law or any other laws and regulations by applying whole or a part of the Licensed Software.

Article 3 Conditions for Grant of License

1. When the User transfers the Product, it may also transfer the license to use the Licensed Software

embedded in the Product (including any related materials, updates and upgrades) on condition that

no original, copies or related materials continue in the possession of the User, and that the User shall

cause the transferee to comply with this Software License Agreement.

2. The User shall not carry out reverse engineering, disassembling, decompiling or any other code

analysis works in connection with the Licensed Software.

Article 4 Right pertaining to the Licensed Software

Any and all copyrights and other rights pertaining to the Licensed Software and related documents

shall belong to the Licensor or the original holder of the right who granted to the Licensor the license or

sublicense for the Licensed Software (hereinafter the "Original Rightholder"), and the User shall not be

entitled to any right other than the license granted hereunder, in respect of the Licensed Software and any

related documents.

Article 5 Indemnification of Licensor

1. Neither the Licensor nor the Original Rightholder shall be liable for any damage incurred by the User

or any third party due to the exercise of the license granted to the User under this Agreement, unless

otherwise restricted by law.

2. The Licensor will offer no guarantee for the merchantability, convertibility and consistency with

certain objective of the Licensed Software.

Article 6 Liability to Third Party

If any dispute has arisen with any third party due to an infringement upon a copyright, patent or any

other intellectual property right that was caused by the User's use of the Licensed Software, the User shall

settle such dispute at its own cost and hold the Licensor and the Original Rightholder harmless from any

inconvenience it may cause.

Article 7 Confidentiality

The User shall keep the confidentiality of such portion of the Licensed Software, related documents thereof

or any other information to be granted under this Agreement, as well as the conditions of this Agreement

as has not yet entered the public domain, and shall not disclose or divulge the same to any third party

without approval of the Licensor.

Article 8 Termination

In case the User falls under any of the events described in the following items, the Licensor may

immediately terminate this Agreement or claim that the User compensates for the damage incurred by the

Licensor due to such event:

(1) when the User violated any provision of this Agreement; or

(2) when a petition has been filed against the User for an attachment,

provisional attachment, provisional disposition or any other compulsory execution.

Article 9 Destruction of the Licensed Software

If this Agreement is terminated pursuant to the provision of Article 8, the User shall destroy the Licensed

Software, any related documents and copies thereof within two (2) weeks from such date of termination.

JS_KWD_KDC_X303_KN_C.indd iiiJS_KWD_KDC_X303_KN_C.indd iii 4/6/2018 11:26:21 AM4/6/2018 11:26:21 AM

Data Size: B6L (182 mm x 128 mm)

Book Size: B6L (182 mm x 128 mm)

iv

Article 10 Protection of Copyright

1. The copyright and all the other intellectual property rights

relating to the Licensed Software shall belong to the Licensor

and the Original Rightholder, and in no event shall they be

under the ownership of the User.

2. The User shall, whenever it uses the Licensed Software,

comply with any laws relating to the copyright and other

intellectual property rights.

Article 11 Export Restriction

1. It is prohibited to export the Licensed Software and any

related documents outside the country of the User (including

transmission thereof outside the country of the User via

Internet of other communication tools).

2. The User shall understand that the Licensed Software shall be

subject to the export restrictions adopted by the country of

User and any other countries.

3. The User shall agree that the software will be subject to any

and all applicable international and domestic laws (including

the export control regulation of the country of User and

any other countries, and any restrictions concerning the

end-users, the use by end-users and importing countries to be

provided by the country of User and any other countries, and

any other governmental authorities).

Article 12 Miscellaneous

1. In the event any part of this Agreement is invalidated by

operation of law, the residual provisions shall continue in

force.

2. Matters not stipulated in this Agreement or any ambiguity or

question raised in the construction of this Agreement shall be

provided or settled upon good-faith consultation between the

Licensor and the User.

3. The Licensor and the User hereby agree that this Agreement

is governed by the laws of Japan, and any dispute arising

from, and relating to the rights and obligations under, this

Agreement shall be submitted to the exclusive jurisdiction of

the Tokyo District Court for its first instance.

Important Notice concerning the Software

-jansson

Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the "Software"),

to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/

or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:

The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.

THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES

OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS

BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR

IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.

-cJSON