Simplicity 1696674-00 Manuel utilisateur

Catégorie
Souffleuses à neige
Taper
Manuel utilisateur

Ce manuel convient également à

Not for Reproduction
Operator’s Manual
Dual Stage Snowthrower
Model No. C950-52591-1 (1696674-00)
Sears Canada Inc., Toronto, Ontario M5B 2C3
Visit our Craftsman website: www.sears.ca/craftsman
Copyright © Briggs & Stratton Corporation, Milwaukee, WI, USA
All rights reserved.
80016112
Revision A
Not for Reproduction
Manual Contents
Thank You Statement .................................................................2
ID Tag and Location
....................................................................2
Operator Safety
..........................................................................3
Safety Decals
..............................................................................8
Safety System Tests
...................................................................9
Features and Controls
.............................................................10
Operation
..................................................................................12
Maintenance
.............................................................................17
Troubleshooting
.......................................................................20
Specications
...........................................................................21
Warranty
....................................................................................22
The images in this document are representative, and
are meant to complement the instructional copy they
accompany. Your unit may vary from the images displayed.
LEFT and RIGHT are as seen from the operator’s position.
THANK YOU STATEMENT
Thank you for purchasing this quality-built CRAFTSMAN®
Snowthrower. We’re pleased that you’ve placed your
confidence in the CRAFTSMAN brand. When operated and
maintained according to the manuals, your CRAFTSMAN
product will provide many years of dependable service.
The manuals contain safety information to make you aware
of the hazards and risks associated with the unit and how to
avoid them. This Snowthrower was designed to be used as
described in operator’s manual and is not intended for any
other purpose. It is important that you read and understand
the instructions thoroughly before attempting to start or
operate this equipment. Save these original instructions
for future reference.
This product requires final assembly before use. Refer
to the setup guide for instructions on final assembly
procedures. Follow the instructions completely.
ID TAG AND LOCATION
USA
XXXXX
For Parts and Service Call
Pour des pices et l’intervention
SEARS CANADA INC.
Toronto, Ontario M5B2C3
MODEL / MODÈLE
SERIAL NO. / NO. SÉRIE
Assembled In
Rassemblé dans
PRODUCT IDENTIFICATION /
IDENTIFICATION DE PRODUIT
XXXXXXXXXXXXXXXXXXXX
XXXXXXX - XX
XXXXXXXXX
XXX-XXX-XXXX
WWW.XXXXXX.COM
X X X X X X X X X X X X
Product Model Number:
Product Serial Number:
Engine Model-Type Number:
Engine Code/Serial Number:
Date of Purchase:
Purchase Location:
When contacting your authorized dealer for replacement
parts, service, or information you MUST have these
numbers.
Record your model name/number, manufacturer’s
identification numbers, and engine serial numbers in the
space provided for easy access. These numbers can be
found in the locations shown.
2
Not for Reproduction
en
Hazard Symbol Charts
Snowthrower Hazard Symbols
Symbol Meaning Symbol Meaning
Safety
information
about hazards
that can result in
personal injury.
Read and
understand
the operator’s
manual before
operating or
servicing the
unit.
Amputation
hazard - rotating
impeller.
Remove the
key before
performing
service.
Amputation
hazard - rotating
impeller.
Amputation
hazard - rotating
auger.
Amputation
hazard - do not
touch moving
parts.
Thrown objects
hazard.
Fire hazard. Explosion
hazard.
Shock hazard. Toxic fume
hazard.
Hot surface
hazard.
Ear protection
recommended
for extended use.
Keep a safe
distance.
Wear safety
glasses.
Keep children
away.
Kickback hazard.
The product identification tag (A) can be found in the
location shown in Figure 1.
1
OPERATOR SAFETY
Safety Alert Symbol and Signal Words
The safety alert symbol indicates a potential personal
injury hazard. A signal word (DANGER, WARNING, or
CAUTION) is used with the alert symbol to designate a
degree or level of hazard seriousness. A safety symbol may
be used to represent the type of hazard. The signal word
NOTICE is used to address practices not related to
personal injury.
DANGER indicates a hazard which, if not avoided,
will result in death or serious injury.
WARNING indicates a hazard which, if not avoided,
could result in death or serious injury.
CAUTION indicates a hazard which, if not avoided,
could result in minor or moderate injury.
NOTICE indicates an action that could result in damage
to the product.
A
3
Not for Reproduction
Regional Warnings
WARNING
U.S.A. Models: Certain components in this product and
its related accessories contain chemicals known to the
state of California to cause cancer, birth defects, or other
reproductive harm. Wash hands after handling.
WARNING
U.S.A. Models: The engine exhaust from this product
contains chemicals known to the State of California to cause
cancer, birth defects, or other reproductive harm.
General Safety Warnings
WARNING
Hand contact with the rotating impeller inside the
discharge chute is the most common cause of injury
associated with snowthrowers.
This snowthrower is capable of amputating hands and
feet, and throwing objects. Read and observe all the
safety instructions in this manual. Failure to do so could
result in death or serious injury.
WARNING
Read, understand, and follow all the instructions on the
snowthrower and in the operator’s manual before operating
this unit.
Failure to observe the safety instructions in this manual could
result in death or serious injury.
Be thoroughly familiar with the controls and the proper
use of the snowthrower.
Make sure you are properly trained before operating the
snowthrower.
Know how to stop the unit and disengage the controls
quickly.
Never allow anyone to operate the snowthrower without
proper instruction.
Always follow the instructions in the operator’s manual, if
the snowthrower will be stored for an extended period.
Maintain or replace safety and instruction labels as
necessary.
Never attempt to make major repairs on the snowthrower
unless you have been properly trained. Improper servicing
of the snowthrower can result in hazardous operation,
equipment damage, and voiding of the product warranty.
DANGER
The discharge chute contains a rotating impeller to throw
snow. Never clear or unclog the discharge chute with your
hands. Fingers can quickly become caught in the impeller.
Always use a clean-out tool.
Failure to observe these safety instructions will result in
traumatic amputation or severe laceration.
DANGER
Keep hands, feet, and clothing away from rotating parts.
Rotating parts can contact or entangle hands, feet, hair,
clothing, or accessories.
Failure to observe these safety instructions will result in
traumatic amputation or severe laceration.
Whenever cleaning, repairing, or inspecting the
snowthrower, make sure the engine is OFF, spark plug
wire is disconnected, and all moving parts have stopped.
Do not put hands or feet near or under rotating parts.
Keep clear of the discharge opening at all times.
Never operate the snowthrower without proper guards,
and other safety devices in place and working.
Never leave the snowthrower unattended while engine
is running. Always disengage the auger and traction
controls, stop engine, and remove keys.
Keep all loose clothing away from the front of the
snowthrower and auger. Scarves, mittens, dangling
drawstrings, loose clothes, and pants can quickly become
caught in the rotating device and amputation will occur.
Tie up long hair and remove jewelry.
Run the machine a few minutes after discharging snow to
prevent freeze-up of the collector/impeller.
Disengage power to the collector/impeller when
snowthrower is transported or not in use.
4
Not for Reproduction
en
WARNING
Objects can be picked up by the auger and thrown from the
chute. Never discharge snow toward bystanders or allow
anyone in front of the snowthrower. Failure to observe these
safety instructions will result in death or serious injury.
Always wear safety glasses or eye shields during
operation, and while performing an adjustment or repair.
Always be aware of the direction the snow is being
thrown. Nearby pedestrians, pets, or property may be
harmed by objects being thrown.
Be aware of your environment while operating the
snowthrower. Don’t run over items such as gravel,
doormats, newspapers, toys, and rocks hidden under
snow, as they can all be thrown from the chute or jam in
the auger.
Use extreme caution when operating on or crossing
gravel drives, walks, or roads.
Adjust the collector housing height to clear gravel or
crushed rock surface.
Never operate the snowthrower near glass enclosures,
automobiles, window wells, drop-offs, and the like without
proper adjustment of the discharge chute angle.
Familiarize yourself with the area in which you plan
to operate the snowthrower. Mark off boundaries of
walkways and driveways.
WARNING
Tragic accidents can occur if the operator is not alert to the
presence of children. Children are often attracted to the unit
and the operating activity. Never assume that children will
remain where you last saw them.
Keep children out of the area during operation. Children
are often attracted to the equipment. Be mindful of all
persons present.
Be alert and turn the unit off if children enter the area.
Never allow children to operate the unit.
Use extra care when approaching blind corners, shrubs,
trees, or other objects that may obscure vision. Children
may be present.
WARNING
Engines give off carbon monoxide, an odorless, colorless,
poison gas. Breathing carbon monoxide can cause nausea,
fainting, or death.
Start and run the engine outdoors.
Do not run the engine in an enclosed area, even if doors
and windows are open.
WARNING
Fuel and its vapors are extremely flammable and explosive.
Always handle fuel with extreme care.
Failure to observe these safety instructions can cause a fire
or explosion which will result in severe burns or death.
When Adding Fuel
Turn off engine and let cool at least 2 minutes before
removing the fuel cap and adding fuel.
Fill fuel tank outdoors or in a well ventilated area.
Do not overfill the fuel tank. To allow for the expansion of
gasoline, do not fill above the bottom of the fuel tank neck.
Keep fuel away from sparks, open flames, pilot lights,
heat, and other ignition sources.
Check fuel lines, cap, and fittings frequently for cracks or
leaks. Replace if necessary.
Use an approved fuel container.
If fuel spills, wait until it evaporates before starting engine.
When Starting Engine
Ensure that spark plug, muffler, fuel cap, and air cleaner
(if equipped) are in place and secured.
Do not crank the engine with the spark plug removed.
If fuel is spilled, do not attempt to start the engine, but
move the snowthrower away from the area of the spill, and
avoid creating any source of ignition, until the fuel vapors
have dissipated.
Do not over-prime the engine. Follow the engine starting
instructions in this manual.
If the engine floods, set choke (if equipped) to OPEN/
RUN position, move throttle (if equipped) to FAST position
and crank until engine starts.
When Operating Equipment
Do not tip the snowthrower at an angle which causes the
fuel to spill.
Do not choke the carburetor to stop the engine.
Never run the engine with the air cleaner assembly (if
equipped) or the air filter (if equipped) removed.
When Changing Oil
If you drain the oil from the top oil fill tube, the fuel tank
must be empty or fuel can leak out and result in a fire or
explosion.
When Transporting Equipment
Transport with fuel tank EMPTY, or with fuel shut-off valve
OFF.
When Storing Gasoline or Equipment With Fuel in
Tank
Store away from furnaces, stoves, water heaters, or other
appliances that have pilot light or other ignition source
because they can ignite fuel vapors.
5
Not for Reproduction
WARNING
This snowthrower must be properly maintained to ensure
safe operation and performance. Failure to observe the
safety instructions in this manual could result in death or
serious injury.
When performing any maintenance or repairs on the
snowthrower, shut OFF the engine, disconnect spark plug
wire, and keep the wire away from the plug to prevent
someone from accidently starting the engine.
Check shear bolts and other hardware at frequent
intervals for proper tightness.
Keep nuts and bolts tight and keep snowthrower in good
condition.
Never tamper with safety devices. Check their proper
operation regularly and make necessary repairs if they
are not functioning properly.
Components are subject to wear, damage, and
deterioration. Frequently check components and replace
with recommended parts, when necessary.
Check control operation frequently. Adjust and service as
required.
Use only factory authorized replacement parts, or like,
parts when making repairs.
Always comply with factory specifications on all settings
and adjustments.
Use only factory authorized, or like, attachments and
accessories such as wheel weights, counterweights, or
cabs.
Never attempt to make any adjustments while the engine
is running (except when specifically recommended by the
factory).
WARNING
Safe operation of the snowthrower requires the proper
care and maintenance of the engine.
Disengage all clutches and shift into neutral before
starting the engine.
Let the engine adjust to outdoor temperatures before
starting to clear snow.
Use a grounded three-wire plug for all snowthrowers
equipped with electric drive motors or electric starting
motors.
WARNING
Starting the engine creates sparking.
Sparking can ignite nearby flammable gases.
Explosion and fire could result.
If there is natural gas or LP gas leakage in the area, do
not start the engine.
Do not use pressurize starting fluids because their vapors
are flammable.
WARNING
Running the engine produces heat. Engine parts,
especially the muffler, become extremely hot.
Failure to observe these safety instructions could result in
severe thermal burns on contact.
Never touch a hot engine or muffler. Allow muffler, engine
cylinder, and fins to cool before touching.
Remove debris from muffler area and cylinder area.
Install and maintain in working order a spark arrester
before using equipment on forest-covered, grass-covered,
or brush-covered unimproved land.
U.S.A. Models: It is a violation of California Public
Resource Code Section 4442 to use or operate the
engine on any forest-covered, brush-covered, or grass-
covered land unless the exhaust system is equipped with
a spark arrester, as defined in Section 4442, maintained
in effective working order. Other states or federal
jurisdictions may have similar laws. Contact the original
equipment manufacturer, retailer, or dealer to obtain a
spark arrester designed for the exhaust system installed
on this engine.
6
Not for Reproduction
en
WARNING
Damaged or ungrounded power cords could cause
electric shock.
Electric shock could cause severe burns or death.
When Using the Electric Starter
The power cord must be properly grounded at all times.
Use only a three-conductor power cord properly grounded
to the power source.
If the power cord is damaged, it must be replaced by a
qualified person to avoid a hazard.
WARNING
Rapid retraction of the starter cord (kickback) will pull
your hand and arm toward the engine faster than you can
let go.
Broken bones, fractures, bruises, or sprains could result.
When starting the engine
Pull the starter cord slowly until resistance is felt and then
pull rapidly to avoid kickback.
WARNING
This snowthrower is only as safe as the operator. If it is
misused, or not properly maintained, it can be dangerous.
Remember you are responsible for your safety and those
around you.
Keep the area of operation clear of all persons,
particularly small children and pets.
Thoroughly inspect the area where the snowthrower will
be used and remove all doormats, sleds, boards, wires,
and other foreign objects.
Do not operate the snowthrower without wearing
adequate winter clothing.
Wear footwear that will improve footing on slippery
surfaces.
Use caution to avoid slipping or falling especially when
operating the snowthrower in reverse.
Never operate the snowthrower without good visibility or
light. Always be sure of your footing, and keep a firm hold
on the handles.
Do not clear snow across the face of slopes. Use extreme
caution when changing direction on slopes. Do not
attempt to clear steep slopes.
Do not overload the machine capacity by attempting to
clear snow too quickly.
Never operate the snowthrower at high transport speeds
on slippery surfaces. Look behind the snowthrower and
use care when operating in reverse.
Do not use the snowthrower on surfaces above ground
level such as roofs of residences, garages, porches, or
other such structures or buildings.
Operators should evaluate their ability to operate the
snowthrower safely enough to protect themselves and
others from injury.
The snowthrower is intended to remove snow only. Do not
use the snowthrower for any other purpose.
Do not carry passengers.
After striking a foreign object, shut OFF the engine,
disconnect the cord on electric motors, thoroughly inspect
the snowthrower for any damage, and repair the damage
before restarting and operating the snowthrower.
If the snowthrower vibrates abnormally, shut OFF the
engine. Vibration is generally a warning of trouble. See an
authorized dealer if necessary for repairs.
For models equipped with electric starting motors,
disconnect the power cord after the engine starts.
7
Not for Reproduction
SAFETY DECALS
2
Part No. 1737865
Chute Danger Decal
Part No. 1751582
Shift Decal
Part No. 1737866
Auger Danger Decal
Part No. 278297
Engine Decal
Part No. 1737869
Auger Control Decal
Part No. 1737870
Traction Control Decal
Part No. 1752992
Main Dash Decal
Before operating your unit, read the safety decals. The
cautions and warnings are for your safety. To avoid a
personal injury or damage to the unit, understand and
follow all the safety decals.
WARNING
If any safety decals become worn or damaged, and
cannot be read, order replacement decals from your local
dealer.
8
Not for Reproduction
en
SAFETY SYSTEM TESTS
DANGER
Amputation hazard
This snowthrower is equipped with several mechanical
safety systems designed to keep the operator safe while
using the unit. Check the operation of these systems
regularly using the safety system tests listed. If the unit
fails to operate as described, DO NOT operate it. See
your authorized dealer for service immediately.
Test 1 - Auger/Impeller Control
With the engine running:
Press down on the auger control lever. (The auger/impeller
should rotate)
Release the auger control lever. (The auger/impeller must
stop within 5 seconds)
Test 2 - Traction Drive Control
With the engine running and speed control in 1st gear:
Press down on the traction control lever. (The unit should
move forward)
Release the traction control lever. (The unit must stop)
Test 3 - Free Hand Control
With the engine running:
Engage the auger and traction control levers, then release
the auger control lever. (Both controls should remain
engaged)
Next, release the traction control lever. (Both controls must
release)
9
Not for Reproduction
SAFETY DECALS
3
1
2
1
2
1
2
B
C
A
K
D
G
E
F
J
H
I
Snowthrower
A. Speed Select Lever — Allows the operator to select
forward and reverse speeds (see Figure 3). To shift,
move speed select lever to desired position.
NOTICE: Do not move speed select lever while Traction
Control is engaged. This may result in severe damage
to the drive system.
B. Auger Control Lever — Used to engage and
disengage the auger and impeller. To engage push
down, to disengage release.
C. Chute Rotation Switch — Used to rotate the discharge
chute to the left or right.
D. Deflector Control Switch — Used to control the angle
of the chute deflector (up or down).
E. Easy-TurnTM Traction Control — When engaged,
allows the operator to release one drive wheel, but
allows the other wheel to continue driving for easy
turning.
F. Free-HandTM Control — After engaging the traction
control (left hand) and auger control (right hand), allows
the operator to release the auger control lever to use the
other controls.
G. Traction Control Lever — Used to propel snowthrower
forward or reverse. Push down to engage, release to
disengage. See also, “Free-Hand Control”.
H. Clean-Out Tool — Used to remove snow and debris
from the discharge chute and the auger housing.
I. Skid Shoes — Used to adjust the ground clearance of
the auger housing.
10
Not for Reproduction
en
4
C
D
A
G
H
I
B
E
F
J. Headlight — Used to operate the snowthrower in poor
lighting conditions.
K. Grip Warmer Switch — Used to warm the hand grips
(On/Off).
Engine
A. Choke Control Knob — Used to start a cold engine
(see Figure 4).
B. Electric Start Button — Used to start the engine using
the electric starter.
C. Primer Button — Used to inject fuel directly into the
carburetor manifold to ensure fast starts in cool weather.
D. On/Off Key - Turn to the ON position to run engine, or
turn to the OFF position to stop the engine.
E. Starter Cord Handle — Used to start the engine
manually.
F. Throttle Control Lever — Used to control engine
speed. For best performance, the throttle control should
be set to the FAST position. Use the SLOW position
only for warming the engine.
G. Fuel Shut-Off Valve — Used to turn the fuel supply off
for out-of-season storage.
H. Fuel Tank and Cap — Fill the fuel tank to approximately
1-1/2 in. (38 mm) below the top of the neck to allow for
fuel expansion.
I. Oil Fill Cap (Extended Dipstick)
11
Not for Reproduction
DANGER
Toxic fume hazard
Engines give off carbon monoxide, an odorless,
colorless, poison gas.
Breathing carbon monoxide can cause nausea,
fainting, or death.
Start and run the engine outdoors.
Do not run the engine in an enclosed area, even if doors
and windows are open.
WARNING
Thrown objects hazard
This machine is capable of throwing objects that could
injure bystanders, or cause damage to buildings.
Be sure the operating area is clear of bystanders. Never
direct the discharge toward anyone, or toward buildings
or cars.
1. Start the engine. See Start the Engine in this section.
2. Press the chute rotation switch (C, Figure 3) to rotate
the discharge chute left or right.
3. Press the deflector control switch (D) to control the
angle of the chute deflector.
4. Fully press and hold the auger control lever (B) to
engage the auger rotation. Releasing the auger control
lever will disengage the auger - unless the Free-Hand™
control is activated.
5. Fully press and hold the traction/Free-Hand™ control
lever (G) to engage the traction drive and begin moving
the snow-thrower. To disengage the traction drive,
completely release the lever.
6. When BOTH levers are pressed, the Free-Hand™
control is activated. This allows you to release the auger
control lever to use the other controls. The auger will
continue to run until the traction/Free-Hand™ control
lever is released.
NOTE: Always release the traction control lever before
changing speeds.
7. Use the speed select lever (A) to select the forward or
reverse drive speed. Use lower speeds when clearing
wet, heavy snow. Use higher speeds for light snow or
transporting.
8. Press the grip warmer switch (K) to heat the hand grips.
9. To stop moving forward, release the traction control
lever (G).
10. To move the snowthrower backwards, move the speed
select lever into either first or second reverse position
and engage the traction control lever.
Before Operating the Snowthrower
WARNING
Read the operator’s manual before operating the
machine. This machine can be dangerous if used
carelessly.
Never operate the snowthrower without all guards, covers,
and shields in place.
Stop the engine whenever leaving the operating position.
Remove the key before unclogging the impeller housing
or discharge chute, and before making repairs or
adjustments.
When leaving the machine, remove the key.
To reduce the risk of fire, keep the machine clean and free
from spilled fuel, oil, and debris.
On electric start models, disconnect the extension cord
before operating.
Be sure to check the engine oil level before starting
the engine. See the engine operator’s manual for oil
recommendations.
Operating the Snowthrower
DANGER
Amputation hazard
The discharge chute contains a rotating impeller
to throw snow. Fingers can quickly become caught
in the impeller. Never clear or unclog the discharge
chute with your hands. Always use a clean-out tool.
Failure to observe these safety instructions will
result in traumatic amputation or severe laceration.
Hand contact with the rotating impeller inside the
discharge chute is the most common cause of injury
associated with snowthrowers. Never use your hands to
clean out the discharge chute.
To safely clear a clogged discharge chute, follow
these instructions:
1. Shut OFF the engine.
2. Wait 10 seconds to be sure the impeller blades have
stopped rotating.
3. Always use a clean-out tool, not your hands.
OPERATION
12
Not for Reproduction
en
Stop the Snowthrower
1. Release the auger control lever (B, Figure 3).
2. Release the traction control lever (G).
3. Move the throttle control lever (F, Figure 8) to SLOW and
then to the STOP position.
4. Turn the ON/OFF key (D) to the OFF position.
5. Remove the key.
6. Keep the key out of the reach of children.
7. After the engine stops, turn the fuel shut-off valve (G) to
the closed position.
Easy Turn™ Traction Control
For easy turning when using the snowthrower, squeeze the
EasyTurn™ lever.
Engaging the Easy-Turn lever releases the left or right
traction wheel, but allows the opposite wheel to continue
driving. Figure 5 shows the left Easy-Turn lever engaged.
Releasing the Easy-Turn lever automatically engages both
drive wheels for full traction (see Figure 6).
NOTE: The Easy-Turn will be more difficult to activate under
a heavy load. Activate the lever before beginning a turn.
5
1
2
1
2
6
Check the Oil
NOTE: The engine was shipped from the factory filled with
oil. Check the level of the oil. Add oil as needed.
1. Make sure the unit is level. Use a high quality detergent
oil classified “For Service SF, SH, SJ, SL, or higher”.
2. Remove the oil fill cap/dipstick (A, Figure 7) and wipe
with a clean cloth.
7
3. Insert the oil fill cap/dipstick and turn clockwise to
tighten.
4. Remove the oil fill cap/dipstick and check the oil.
NOTE: Do not check the level of the oil while the engine
runs.
5. If necessary, add oil until the oil reaches the FULL mark
on the oil fill cap/dipstick (B). Do not add too much oil.
6. Tighten the oil fill cap/dipstick securely each time you
check the oil level.
NOTE: For extreme cold operating conditions of 0°F (-18°C)
and below, use a synthetic 5W30 motor oil for easier start-
ing.
NOTE: S.A.E. 5W30 motor oil may be used to make starting
easier in areas where the temperature is 20°F (-7°C) to 0°F
(-18°C). Synthetic 5W30 is acceptable for all temperatures.
DO NOT mix oil with gasoline. See Chart for oil recom-
mendations.
FULL
A
13
Not for Reproduction
* Below 40°F (4°C) the use of SAE 30 will result in hard starting.
** Above 80°F (27°C) the use of 10W-30 may cause increased oil con-
sumption. Check oil level more frequently.
Fuel Recommendations
Fuel must meet these requirements:
Clean, fresh, unleaded gasoline.
A minimum of 87 octane / 87 AKI (91 RON). For high
altitude use, see below.
Gasoline with up to 10% ethanol (gasohol) is acceptable.
NOTICE: Do not use unapproved gasolines, such as E15
and E85. Do not mix oil in gasoline or modify the engine to
run on alternate fuels. Use of unapproved fuels will cause
damage to engine components, which will not be covered
under warranty.
To protect the fuel system from gum formation, mix a fuel
stabilizer into the fuel. See Storage. All fuel is not the
same. If starting or performance problems occur, change
fuel providers or change brands. This engine is certified to
operate on gasoline. The emissions control system for this
engine is EM (Engine Modifications).
High Altitude
At altitudes over 5,000 feet (1524 meters), a minimum
85 octane / 85 AKI (89 RON) gasoline is acceptable. For
carbureted engines, high altitude adjustment is required
to remain emissions compliant. Operation without this
adjustment will cause decreased performance, increased
fuel consumption, and increased emissions. Contact
a Briggs & Stratton Authorized Service Dealer for high
altitude adjustment information.
Operation of the engine at altitudes below 2,500 feet
(762 meters) with the high altitude adjustment is not
recommended. For Electronic Fuel Injection (EFI) engines,
no high altitude adjustment is necessary.
Adding Fuel
WARNING
Fuel and its vapors are extremely flammable and
explosive.
Fire or explosion can cause severe burns or death.
When Adding Fuel
• Turn engine off and let engine cool at least 2 minutes
before removing the fuel cap.
• Fill fuel tank outdoors or in well-ventilated area.
• Do not overfill fuel tank. To allow for expansion of the
fuel, do not fill above the bottom of the fuel tank neck.
• Keep fuel away from sparks, open flames, pilot lights,
heat, and other ignition sources.
• Check fuel lines, tank, cap, and fittings frequently for
cracks or leaks. Replace if necessary.
• If fuel spills, wait until it evaporates before starting
engine.
Start the Engine
Be sure that engine oil is at FULL mark on the oil fill cap/
dipstick. The snowthrower engine is equipped with an A.C.
electric starter and recoil starter. Before starting the engine,
be certain that you have read the following information.
If engine floods, set the choke to the OPEN/RUN position
and crank until the engine starts.
WARNING: The electric starter is equipped with a
three−wire power cord and plug designed to operate on
AC house hold current. The power cord must be properly
grounded at all times to avoid the possibility of electric
shock which can cause injury to the operator. Follow all
instructions carefully as set forth:
Make sure your house has a three−wire grounded
system.
If you are not sure, ask a licensed electrician. If your
house does not have a three−wire grounded system, do
not use this electric starter under any condition.
If your house has a three−wire grounded system but
a three-hole receptacle is not available to connect the
electric starter, have a three−hole receptacle installed by
a licensed electrician.
WARNING: To connect power cord, always
connect the power cord first to the switch box
located on the engine and then plug the other end
into a three−hole grounded receptacle.
WARNING: To disconnect the power cord, always
unplug the end connected to the three-hole
grounded receptacle first.
14
Not for Reproduction
en
Start the engine as follows:
1. Check the oil level.
2. Make sure equipment drive controls are disengaged.
3. Turn the fuel shut-off valve (A, Figure 8) to the ON
position.
4. Insert the ON/OFF key (B) and turn to the ON/START
position.
5. Move the throttle control lever (C) to the FAST position.
Operate the engine with the throttle control in the fast
position.
6. Turn the choke control knob (D) to the CHOKE position.
NOTE: Choke is usually unnecessary when restarting a
warm engine.
7. Push the primer (E) two times.
NOTE: Priming is usually unnecessary when restarting a
warm engine.
8
E
D
B
A
C
8. Rewind Start: Firmly hold the starter cord handle
(A, Figure 9). Pull the starter cord handle slowly until
resistance is felt, then pull rapidly.
WARNING
Rapid retraction of the starter cord (kickback) will pull
your hand and arm toward the engine faster than you can
let go.
Broken bones, fractures, bruises, or sprains could result.
When starting the engine
Pull the starter cord slowly until resistance is felt and then
pull rapidly to avoid kickback.
NOTE: If the engine does not start after three attempts, see
an authorized dealer.
9
A
9. Electric Start: First connect the extension cord to the
power cord receptacle and then into a wall receptacle.
If additional extension cord is required, make sure it is
three-wire.
WARNING: If the extension cord is damaged,
it must be replaced by the manufacturer (or its
service agent) or a similarly qualified person to
avoid a hazard.
10. Electric Start: Depress the starter push button (A,
Figure 10). After you start the engine, first disconnect
the extension cord from the wall receptacle and then
from the power cord receptacle (B).
NOTICE: To extend the life of the starter, use short starting
cycles (five seconds maximum). Wait one minute between
starting cycles.
NOTE: If the engine does not start after three attempts, see
an authorized dealer.
11. Allow the engine to warm up for several minutes. Then
slowly move the choke control knob to the RUN position.
10
A
B
15
Not for Reproduction
Stop the Engine
WARNING
Gasoline and vapors are extremely flammable and
explosive.
Fire or explosion can cause severe burns or death.
Do not choke the carburetor to stop the engine.
1. Move the throttle control lever (C, Figure 8) to SLOW
and then to the STOP position.
2. Turn the ON/OFF key (B) to the OFF position.
3. Remove the key. Keep the key out of the reach of
children.
4. After the engine stops, turn the fuel shut-off valve (A) to
the closed position.
Clearing a Clogged Discharge Chute
DANGER
Amputation hazard
The discharge chute contains a rotating impeller
to throw snow. Fingers can quickly become caught
in the impeller. Never clear or unclog the discharge
chute with your hands. Always use a clean-out tool.
Failure to observe these safety instructions will
result in traumatic amputation or severe laceration.
Hand contact with the rotating impeller inside the
discharge chute is the most common cause of injury
associated with snowthrowers. Never use your hands to
clean out the discharge chute.
To safely clear a clogged discharge chute, follow
these instructions:
1. Shut OFF the engine.
2. Wait 10 seconds to be sure the impeller blades have
stopped rotating.
3. Always use a clean-out tool, not your hands.
A clean-out tool (A, Figure 11) is provided with the unit.
11
A
Skid Shoe Height Adjustment
DANGER
Amputation hazard
The discharge chute contains a rotating impeller to throw
snow. Fingers can quickly become caught and traumatic
amputation or severe laceration will result. Hand contact
with the rotating impeller inside the discharge chute
is the most common cause of injury associated with
snowthrowers.
Turn the engine OFF, wait for all moving parts to stop,
and remove the engine key before performing any
maintenance or repairs.
WARNING
Thrown objects hazard
Objects such as gravel, rocks, or other debris, if struck by
the impeller, may be thrown with sufficient force to cause
personal injury, property damage, or damage to the
snowthrower.
Be sure to set the skid shoes at the proper height to
maintain ground clearance for the type of surface being
cleared.
This snowthrower is equipped with two height adjust skids,
secured to the outside of the auger housing. These elevate
the front of the snowthrower.
When removing snow from a hard surface area such as
a paved driveway or walk, adjust the skids up to bring the
front of the snowthrower down.
When removing snow from rock or uneven construction,
raise the front of the snowthrower by moving the skids
down. This will help to prevent rocks and other debris from
being picked up and thrown by the augers.
1. Determine how much clearance you want between the
scraper bar at the bottom of the auger housing and the
ground. If clearing a gravel surface, enough ground
clearance is needed to prevent the unit from picking up
rocks.
2. Place a block equal to the desired ground clearance
under the scraper bar.
3. Loosen the skid shoe mounting nuts (A, Figure 12) and
push the skid shoe (B) down until it touches the ground.
Re-tighten mounting nuts.
4. Set the skid shoe on the other side at the same height.
12
B
A
1/8” - 3/16”
(3 mm - 5 mm)
B
A
1”
(2,5 cm)
16
Not for Reproduction
en
Maintenance Chart
SNOWTHROWER
After Each Use
Remove the snow and slush off snowthrower to prevent
freezing of controls
Every 8 Hours or Daily
Perform snowthrower safety tests
Every 25 Hours or Annually *
Check tire pressure
Check snowthrower for loose hardware
See Dealer Annually to
Lubricate control levers and linkages
Lubricate deflector hinge
Lubricate deflector motor (if equipped)
Lubricate chute rotation gear (if equipped)
Emissions Control Statement
Maintenance, replacement, or repair of the emissions
control devices and systems may be performed by any non-
road engine repair establishment or individual. However,
to obtain “no charge” emissions control service, the work
must be performed by a factory authorized dealer. See the
Emissions Warranty.
Engine Maintenance
Check Crankcase Oil Level - Before starting engine
and after each 8 hours of continuous use. Add the
recommended motor oil as required.
NOTE: Over filling the engine can affect performance.
Tighten the oil fill cap securely to prevent leakage.
Change Oil - Every 50 hours of operation or at least once
a year, even if the snowthrower is not used for fifty hours.
Use a clean, high quality detergent oil. Fill the crankcase
to FULL line on dipstick (A, Figure 13). Be sure original
container is marked: A.P.I. service “SF” or higher. Do not use
SAE10W40 oil (as it may not provide proper lubrication).
See Chart for oil recommendations.
Drain Oil – Position snowthrower so that the oil drain plug
is lowest point on engine. When the engine is warm, remove
oil drain plug and oil fill cap and drain oil into a suitable
container.
Replace oil drain plug and tighten securely. Refill crankcase
with the recommended motor oil.
MAINTENANCE
ENGINE
First 5 Hours
Change engine oil
Every 8 Hours or Daily
Check engine oil level
Every 50 Hours or Annually *
Change engine oil
Check muffler and muffler guard
See Dealer Annually to
Replace spark plug
Check valve clearance
* Not required unless there are problems with engine performance.
13
A
* Below 40°F (4°C) the use of SAE 30 will result in hard starting.
** Above 80°F (27°C) the use of 10W-30 may cause increased oil
consumption. Check oil level more frequently.
17
Not for Reproduction
Auger Control Cable Adjustment
WARNING
Do not over-tighten, as this may lift the lever and cause
the auger drive to be engaged without depressing the
auger drive control.cleared.
1. With the auger control lever released, the hook (A,
Figure 14) should barely touch the lever (B) without
raising it. There can be a maximum of 1/32 in. (0.8 mm)
clearance.
2. To adjust, loosen the nut (C) by holding the adjusting
flats (D) and turning the nut. Then, turn the adjusting
flats and hold the adjustment screw (E). The adjustment
screw is a phillips screw and the head can be held or
turned by inserting a screwdriver through the spring (F).
3. Hold the adjusting flats and tighten the nut.
4. Start the engine and check the auger. The auger
must not be engaged unless the auger control lever is
depressed.
5. With the engine running, fully depress the auger
drive control lever. The auger should engage and run
normally.
14
D
C
F
E
A
B
1/32”
(6,8 mm)
WARNING
The auger must stop within 5 seconds. If it does not, see
an authorized dealer.
6. Release the auger control lever.
7. If the auger does not operate properly, stop the engine
and recheck the auger control cable adjustment.
8. If the drive linkage is properly adjusted, the tension of
the auger drive belt may require an adjustment. See an
authorized dealer.
Auger Shear Bolt Replacement
The augers are secured to the auger shaft with special bolts
that are designed to break if an object becomes lodged
in the auger housing. Use of a harder bolt will reduce the
protection provided by the shear bolt.
WARNING
To ensure safety and performance levels, only original
replacement shear bolts should be used.
1. Stop the engine, disengage all controls, disconnect the
spark plug lead wire, and make sure all moving parts
have stopped.
2. Align the hole in the auger with the hole in the auger
shaft. Install new shear bolt (A, Figure 15), spacer (B)
and locknut (C) found in the parts bag or toolbox located
on the belt cover.
NOTE: The spacer fits into the larger hole in the auger tube.
15
B
C
C
A
A
B
Traction Cable Inspection
The cables are adjusted at the factory and no adjustment
should be necessary. However, if the cables have become
stretched or are sagging, adjustment will be necessary.
Please see your dealer for this adjustment.
Traction Drive Belt Adjustment
The traction drive belt is under constant spring tension and
does not require any adjustment. If the traction drive belt is
slipping, see your authorized dealer.
Speed Control Rod Adjustment
If the speed control rod requires adjustment, see an
authorized dealer.
18
Not for Reproduction
en
Storage
WARNING
Fuel and its vapors are extremely flammable and
explossive. Always handle fuel with extreme care.
Failure to observe these safety instructions can cause a
fire or explosion which will result in severe burns or death.
When Storing Gasoline or Equipment With Fuel in
Tank
Store away from furnaces, stoves, water heaters, or other
appliances that have pilot light or other ignition source
because they can ignite fuel vapors.
Fuel System
Fuel can become stale when stored over 30 days. Stale fuel
causes acid and gum deposits to form in the fuel system
or on essential carburetor parts. To keep fuel fresh, use
Briggs & Stratton® Advanced Formula Fuel Treatment
& Stabilizer, available wherever Briggs & Stratton genuine
service parts are sold.
There is no need to drain gasoline from the engine if a fuel
stabilizer is added according to instructions. Run the engine
for 2 minutes to circulate the stabilizer throughout the fuel
system before storage. If gasoline in the engine has not
been treated with a fuel stabilizer, it must be drained into an
approved container. Run the engine until it stops from lack
of fuel. The use of a fuel stabilizer in the storage container is
recommended to maintain freshness.
Engine Oil
While the engine is still warm, change the engine oil. See
Maintenance.
Before Placing in Storage
1. Thoroughly clean the snowthrower.
2. Remove the sparkplug. Clean and re-gap, if necessary,
or replace the sparkplug.
3. Make sure all nuts, bolts, and screws are securely
fastened.
4. Inspect moving parts for wear or damage. Replace
parts as necessary.
5. Lubricate the controls and moving parts.
6. Spray unpainted metal surfaces with a rust preventative.
7. Fold down the upper handle, if desired.
8. For indoor storage, cover the snowthrower and store it
in a dry area away from furnaces, stoves, water heaters,
or other appliances that have pilot lights or other ignition
sources.
9. For outdoor storage, raise the snowthrower off the
ground and cover it with a heavy tarpaulin.
After Removing from Storage
1. Raise the upper handle and tighten the handle knobs
securely.
2. Remove the oil dipstick and check the oil level. If
necessary, add oil until the level reaches the FULL mark
on the oil dipstick. Do not overfill.
3. Fill the fuel tank with fresh fuel.
4. Ensure that all guards, shields, and covers are in place
and that all fasteners are tight.
19
Not for Reproduction
TROUBLESHOOTING
Troubleshooting Chart
Perform the inspection or repair as indicated in the Troubleshooting Chart.
Problem Look for Remedy
Auger does not stop within 5
seconds after right control lever is
released
Free Hand control (if equipped) is
ACTIVE.
Release both auger control and Free
Hand control (if equipped) to stop
auger.
Auger drive belt out of adjustment. See authorized dealer.
Auger belt guide out of adjustment. See authorized dealer.
Discharge chute or deflector does
not work (electric)
Electrical failure. See authorized dealer.
Discharge chute or deflector does
not work (remote-manual)
Discharge chute or deflector out of
adjustment or needs lubrication.
Adjust and/or lubricate control
linkage.
Drive fails to move snowthrower at
slow speeds
Traction control out of adjustment. See authorized dealer.
Engine fails to start Key is in OFF position. Turn key to ON position.
Failure to prime a cold engine. Press primer button twice and restart.
Fuel shut-off valve, if equipped, is in
CLOSED position.
Turn valve to OPEN position.
Out of fuel. Fill fuel tank.
Choke turned to OPEN/RUN with cold
engine.
Turn choke to CLOSED/START, set
throttle to FAST.
Engine flooded. Move the choke to OPEN/RUN
position, move throttle to FAST
position, and crank until the engine
starts.
No spark. See authorized dealer.
Engine starts hard or runs poorly Water in fuel, or old fuel. Drain tank. (Dispose of fuel at an
authorized hazardous waste facility.)
Fill with fresh fuel.
Spark plug faulty, fouled, or gapped
improperly.
See authorized dealer.
Fuel cap vent is blocked. Clear vent.
Excessive vibration Loose parts or damaged impeller. Stop engine immediately. Tighten all
hardware. If vibration continues, have
the unit serviced by an authorized
dealer.
Snowthrower does not stop when
traction control lever is released
Traction control out of adjustment. See authorized dealer.
Scraper bar does not clean hard
surface
Skid shoes and scraper bar improperly
adjusted.
Raise or lower skid shoes and
scraper bar.
Unit fails to propel itself Drive belt loose or damaged. Replace drive belt. See authorized
dealer.
Incorrect adjustment of traction drive
cable.
See authorized dealer.
Worn or damaged friction disc. Replace friction disc. See authorized
dealer.
20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92

Simplicity 1696674-00 Manuel utilisateur

Catégorie
Souffleuses à neige
Taper
Manuel utilisateur
Ce manuel convient également à

dans d''autres langues