Wacker Neuson PDT2A Manuel utilisateur

Operator’s Manual

Diaphragm Pump

Notice d’Emploi

Pompe à membrane

5000184808 04 0612

5000184808

EN / FR

PDI2A

PDI3A

PDT2A

PDT3A

Copyright

notice

All rights, including copying and distribution rights, are reserved.

This publication may be photocopied by the original purchaser of the machine. Any

other type of reproduction is prohibited without express written permission from

Wacker Neuson Production Americas LLC.

Any type of reproduction or distribution not authorized by Wacker Neuson Production

Americas LLC represents an infringement of valid copyrights. Violators will be

prosecuted.

Trademarks

All trademarks referenced in this manual are the property of their respective owners.

Manufacturer

Wacker Neuson Production Americas LLC

N92W15000 Anthony Avenue

Menomonee Falls, WI 53051 U.S.A.

Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957

www.wackerneuson.com

Original

instructions

This Operator’s Manual presents the original instructions. The original language of this

Operator’s Manual is American English.

5000184784 04 0612

PD 2A / PD 3A Foreword

wc_tx001329gb.fm 3

Foreword

SAVE THESE INSTRUCTIONS—This manual contains important instructions for

the machine models below. These instructions have been written expressly by

Wacker Neuson Production Americas LLC and must be followed during installation,

operation, and maintenance of the machines.

Machine

documentation

 From this point forward in this documentation, Wacker Neuson Production

Americas LLC will be referred to as Wacker Neuson.

 Keep a copy of the Operator’s Manual with the machine at all times.

 Use the separate Parts Book supplied with the machine to order replacement

parts.

 If you are missing either of these documents, please contact Wacker Neuson to

order a replacement or visit www.wackerneuson.com.

 When ordering parts or requesting service information, be prepared to provide

the machine model number, item number, revision number, and serial number.

Expectations

for

information in

this manual

 This manual provides information and procedures to safely operate and main-

tain the above Wacker Neuson model(s). For your own safety and to reduce the

risk of injury, carefully read, understand, and observe all instructions described

in this manual.

 Wacker Neuson expressly reserves the right to make technical modifications,

even without notice, which improve the performance or safety standards of its

machines.

 The information contained in this manual is based on machines manufactured

up until the time of publication. Wacker Neuson reserves the right to change

any portion of this information without notice.

CALIFORNIA

Proposition

65 Warning

Engine exhaust, some of its constituents, and certain vehicle components, contain

or emit chemicals known to the State of California to cause cancer and birth

defects or other reproductive harm.

Laws

pertaining to

spark

arresters

NOTICE: State Health Safety Codes and Public Resources Codes specify that in

certain locations spark arresters be used on internal combustion engines that use

hydrocarbon fuels. A spark arrester is a device designed to prevent accidental dis-

charge of sparks or flames from the engine exhaust. Spark arresters are qualified

and rated by the United States Forest Service for this purpose. In order to comply

with local laws regarding spark arresters, consult the engine distributor or the local

Health and Safety Administrator.

Machine Item Number Machine Item Number

PDT 2A 0620769 PDT 3A 0620773

PDI 2A(I) 0620772 PDI 3A 0620775

PDI 3A(I) 0620776

Foreword PD 2A / PD 3A

4 wc_tx001329gb.fm

Manufacturer’s

approval

This manual contains references to approved parts, attachments, and modifica-

tions. The following definitions apply:

 Approved parts or attachments are those either manufactured or provided by

Wacker Neuson.

 Approved modifications are those performed by an authorized Wacker Neu-

son service center according to written instructions published by Wacker Neu-

son.

 Unapproved parts, attachments, and modifications are those that do not

meet the approved criteria.

Unapproved parts, attachments, or modifications may have the following conse-

quences:

 Serious injury hazards to the operator and persons in the work area

 Permanent damage to the machine which will not be covered under warranty

Contact your Wacker Neuson dealer immediately if you have questions about

approved or unapproved parts, attachments, or modifications.

Original Declaration of Conformity

2012-CE-PD2A_PD3A_en.fm

Manufacturer

Wacker Neuson Production Americas LLC, N92W15000 Anthony Avenue,

Menomonee Falls, Wisconsin USA

Product

Product category

Product function

Item number

Net installed power

Measured sound power level

Guaranteed sound power level

PDT 2A, PDT2, PDI 2A(i),

PDT 3A, PDT 3, PDI 3A, PDI 3A(i)

Water Pump Units

To pump fluid

0620769, 0620772, 0620773, 0620775, 0620776

PDT 2A, PDI 2A(i), PDT 3A, PDI 3A, PDI 3A(i): 2.6 kW

PDT 2, PDT 3: 3.2 kW

96 dB(A)

97 dB(A)

Conformity Assessment Procedure

According to ANNEX V

Directives and Standards

We hereby declare that this product meets and complies with the relevant regulations and

requirements of the following directives and standards:

2006/42/EC, 2000/14/EC, EN 809: 1998

Authorized Person for Technical Documents

Axel Häret, Wacker Neuson Produktion GmbH & Co. KG, Preußenstraße 41,

80809 München

Menomonee Falls, WI, USA, 21.05.12

William Lahner

Managing Director

Dan Domanski

Director of Business Development

EC Declaration of Conformity

Travis Pound

Manager, Product Engineering

Table of Contents

PD 2A / PD 3A

wc_bo5000184784_04TOC.fm

7

Foreword 3

EC Declaration of Conformity 5

1 Safety Information 9

1.1 Signal Words Used in this Manual ....................................................... 9

1.2 Machine Description and Intended Use ............................................. 10

1.3 Operating Safety ................................................................................ 11

1.4 Service Safety .................................................................................... 13

1.5 Operator Safety while Using Internal Combustion Engines ............... 15

2 Labels 16

2.1 Label Locations .................................................................................. 16

2.2 Label Meanings .................................................................................. 17

3 Lifting and Transporting 22

4 Operation 23

4.1 Preparing the Machine for First Use ................................................... 23

4.2 Hoses and Clamps ............................................................................. 23

4.3 Recommended Fuel ........................................................................... 24

4.4 Refueling the Machine ........................................................................ 25

4.5 Before Installing the Pump ................................................................. 26

4.6 Installing the Pump ............................................................................. 27

4.7 Starting ............................................................................................... 28

4.8 Stopping ............................................................................................. 29

4.9 Running the Pump .............................................................................. 29

4.10 Clearing Jams .................................................................................... 30

4.11 Emergency Shutdown Procedure ....................................................... 31

Table of Contents

PD 2A / PD 3A

wc_bo5000184784_04TOC.fm

8

5 Maintenance 32

5.1 Maintaining the Emission Control System ...........................................32

5.2 Periodic Maintenance Schedule ..........................................................33

5.3 Servicing the Air Cleaner .....................................................................34

5.4 Greasing the Connecting Rod Bearing ................................................35

5.5 Changing the Engine Oil .....................................................................36

5.6 Cleaning the Sediment Cup ................................................................37

5.7 Spark Plug ...........................................................................................38

5.8 Changing the Gearbox Oil ...................................................................39

5.9 Cleaning the Pump ..............................................................................40

5.10 Storage ................................................................................................41

6 Troubleshooting 42

7 Technical Data 44

7.1 Engine .................................................................................................44

7.2 Pump ...................................................................................................45

7.3 Sound Measurements .........................................................................45

7.4 Dimensions ..........................................................................................46

8 Emission Control Systems Information and Warranty 47

8.1 Emission Control Systems Warranty Statement .................................47

9 AEM Safety Manual 48

PD 2 / PD 3 / PD 2A / PD 3A Safety Information

wc_si000391gb.fm 9

1 Safety Information

1.1 Signal Words Used in this Manual

This manual contains DANGER, WARNING, CAUTION, NOTICE, and NOTE

signal words which must be followed to reduce the possibility of personal injury,

damage to the equipment, or improper service.

NOTICE: Used without the safety alert symbol, NOTICE indicates a situation

which, if not avoided, could result in property damage.

Note: A Note contains additional information important to a procedure.

This is the safety alert symbol. It is used to alert you to potential personal hazards.

f Obey all safety messages that follow this symbol.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will result in death

or serious injury.

f

To avoid death or serious injury from this type of hazard, obey all safety messages that

follow this signal word.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

f

To avoid possible death or serious injury from this type of hazard, obey all safety mes-

sages that follow this signal word.

CAUTION

CAUTION indicates a hazardous situation which, if not avoided, could result in

minor or moderate injury.

f

To avoid possible minor or moderate injury from this type of hazard, obey all safety mes-

sages that follow this signal word.

Safety Information PD 2 / PD 3 / PD 2A / PD 3A

10 wc_si000391gb.fm

1.2 Machine Description and Intended Use

This machine is a diaphragm pump. The Wacker Neuson Diaphragm Pump

consists of a gasoline engine, a fuel tank, a handle, a set of wheels, and a

diaphragm pump with ports for fluid suction and discharge. The engine raises and

lowers the diaphragm via a connecting rod. The operator connects hoses to the

pump and routes them so that water and solids are drained from the work area and

discharged into an appropriate location.

This machine is intended to be used for general de-watering applications. This

machine is intended for the pumping of clear water, or water containing solids up to

the size stated within the product specifications, and up to the flow, head, and

suction lift limits also stated within the product specifications.

This machine has been designed and built strictly for the intended use described

above. Using the machine for any other purpose could permanently damage the

machine or seriously injure the operator or other persons in the area. Machine

damage caused by misuse is not covered under warranty.

The following are some examples of misuse:

 Pumping flammable, explosive, or corrosive fluids

 Pumping hot or volatile fluids that result in pump cavitation

 Operating the pump outside of product specifications due to incorrect diameter

hoses, incorrect length hoses, other inlet or outlet restrictions, or excessive suc-

tion lift or head

 Using the machine as a ladder, support, or work surface

 Using the machine to carry or transport passengers or equipment

 Operating the machine outside of factory specifications

 Operating the machine in a manner inconsistent with all warnings found on the

machine and in the Operator’s Manual

This machine has been designed and built in accordance with the latest global

safety standards. It has been carefully engineered to eliminate hazards as far as

practicable and to increase operator safety through protective guards and labeling.

However, some risks may remain even after protective measures have been taken.

They are called residual risks. On this machine, they may include exposure to:

 Heat, noise, exhaust, and carbon monoxide from the engine

 Fire hazards from improper refueling techniques

 Fuel and its fumes

 Personal injury from improper lifting techniques

 Projectile hazard from discharge

 Crushing hazards from a tipping or falling pump

To protect yourself and others, make sure you thoroughly read and understand the

safety information presented in this manual before operating the machine.

PD 2 / PD 3 / PD 2A / PD 3A Safety Information

wc_si000391gb.fm 11

1.3 Operating Safety

Operator

training

Before operating the machine:

 Read and understand the operating instructions contained in all manuals deliv-

ered with the machine.

 Familiarize yourself with the location and proper use of all controls and safety

devices.

 Contact Wacker Neuson for additional training if necessary.

When operating this machine:

 Do not allow improperly trained people to operate the machine. People operat-

ing the machine must be familiar with the potential risks and hazards associated

with it.

Operator

qualifications

Only trained personnel are permitted to start, operate, and shut down the machine.

They also must meet the following qualifications:

 have received instruction on how to properly use the machine

 are familiar with required safety devices

The machine must not be accessed or operated by:

 children

 people impaired by alcohol or drugs

Application

area

Be aware of the application area.

 Keep unauthorized personnel, children, and pets away from the machine.

 Remain aware of changing positions and the movement of other equipment and

personnel in the application area/job site.

Be aware of the application area.

 Do not operate the machine in areas that contain flammable objects, fuels, or

products that produce flammable vapors.

Safety

devices,

controls, and

attachments

Only operate the machine when:

 All safety devices and guards are in place and in working order.

 All controls operate correctly.

 The machine is set up correctly according to the instructions in the Operator’s

Manual.

 The machine is clean.

 The machine’s labels are legible.

To ensure safe operation of the machine:

 Do not operate the machine if any safety devices or guards are missing or inop-

erative.

 Do not modify or defeat the safety devices.

 Do not use accessories or attachments that are not approved by Wacker Neu-

son.

Safety Information PD 2 / PD 3 / PD 2A / PD 3A

12 wc_si000391gb.fm

Operating

guidelines

When operating this machine:

 Ensure that the machine is on a firm, level surface and that it will not tip, roll,

slide, or fall while operating.

When operating this machine:

 Do not pump volatile, flammable, or low-flash-point fluids.

 Do not change hoses while the engine is running.

 Do not attempt to move the machine while the engine is running.

Personal

Protective

Equipment

(PPE)

Wear the following Personal Protective Equipment (PPE) while operating this

machine:

 Close-fitting work clothes that do not hinder movement

 Safety glasses with side shields

 Hearing protection

 Safety-toed footwear

PD 2 / PD 3 / PD 2A / PD 3A Safety Information

wc_si000391gb.fm 13

1.4 Service Safety

Service

training

Before servicing or maintaining the machine:

 Read and understand the instructions contained in all manuals delivered with

the machine.

 Familiarize yourself with the location and proper use of all controls and safety

devices.

 Only trained personnel should troubleshoot or repair problems occurring with

the machine.

 Contact Wacker Neuson for additional training if necessary.

When servicing or maintaining this machine:

 Do not allow improperly trained people to service or maintain the machine. Per-

sonnel servicing or maintaining the machine must be familiar with the associ-

ated potential risks and hazards.

Precautions

Follow the precautions below when servicing or maintaining the machine.

 Read and understand the service procedures before performing any service to

the machine.

 All adjustments and repairs must be completed before operation. Do not oper-

ate the machine with a known problem or deficiency.

 All repairs and adjustments shall be completed by a qualified technician.

 Turn off the machine before performing maintenance or making repairs.

Personal

Protective

Equipment

(PPE)

Wear the following Personal Protective Equipment (PPE) while servicing or

maintaining this machine:

 Close-fitting work clothes that do not hinder movement

 Safety glasses with side shields

 Hearing protection

 Safety-toed footwear

In addition, before servicing or maintaining the machine:

 Tie back long hair.

 Remove all jewelry (including rings).

Machine

modifications

When servicing or maintaining the machine:

 Use only accessories/attachments that are approved by Wacker Neuson.

When servicing or maintaining the machine:

 Do not defeat safety devices.

 Do not modify the machine without the express written approval of Wacker Neu-

son.

Replacing

parts and

labels

 Replace worn or damaged components.

 Replace all missing and hard-to-read labels.

Safety Information PD 2 / PD 3 / PD 2A / PD 3A

14 wc_si000391gb.fm

 When replacing electrical components, use components that are identical in rat-

ing and performance to the original components.

 When replacement parts are required for this machine, use only Wacker Neu-

son replacement parts or those parts equivalent to the original in all types of

specifications, such as physical dimensions, type, strength, and material.

Lifting and

transporting

When lifting the machine:

 Make sure slings, chains, hooks, ramps, jacks, and other types of lifting devices

are attached securely and have enough weight-bearing capacity to lift or hold

the machine safely. See chapter Technical Data.

 Remain aware of the location of other people when lifting the machine.

 Make sure the transporting vehicle has sufficient load capacity and platform size

to safely transport the machine. See chapter Technical Data.

To reduce the possibility of injury:

 Do not stand under the machine while it is being lifted or moved.

 Do not get onto the machine while it is being lifted or moved.

Cleaning

When cleaning and servicing the machine:

 Keep the machine clean and free of debris such as leaves, paper, cartons, etc.

 Keep the labels legible.

When cleaning the machine:

 Do not clean the machine while it is running.

 Never use gasoline or other types of fuels or flammable solvents to clean the

machine. Fumes from fuels and solvents can become explosive.

PD 2 / PD 3 / PD 2A / PD 3A Safety Information

wc_si000391gb.fm 15

1.5 Operator Safety while Using Internal Combustion Engines

Operating

safety

When operating the pump:

 Keep the area around exhaust pipe free of flammable materials.

 Check the fuel lines and the fuel tank for leaks and cracks before starting the

engine.

When operating the pump:

 Do not smoke while operating the machine.

 Do not run the machine if fuel leaks are present or the fuel lines are loose.

 Do not run the engine near sparks or open flames.

 Do not touch the engine or muffler while the engine is running or immediately

after it has been turned off.

 Do not operate a machine when its fuel cap is loose or missing.

 Do not start the engine if fuel has spilled or a fuel odor is present. Move the

machine away from the spill and wipe the machine dry before starting.

Refueling

safety

When refueling the engine:

 Clean up any spilled fuel immediately.

 Refill the fuel tank in a well-ventilated area.

 Replace the fuel tank cap after refueling.

When refueling the engine:

 Do not smoke.

 Do not refuel a hot or running engine.

 Do not refuel the engine near sparks or open flames.

 Do not refuel if the machine is positioned in a truck fitted with a plastic bed liner.

Static electricity can ignite the fuel or fuel vapors.

WARNING

Internal combustion engines present special hazards during operation and fueling.

Failure to follow the warnings and safety standards could result in severe injury or

death.

f Read and follow the warning instructions in the engine owner’s manual and the

safety guidelines below.

DANGER

Asphyxiation hazard. Using a pump indoors CAN KILL YOU IN MINUTES. Pump

exhaust contains carbon monoxide. This is a poison you cannot see or smell.

f NEVER use this pump inside a home or garage, EVEN IF doors and windows

are open. Only use OUTSIDE and far away from windows, doors, and vents.

f NEVER use a pump inside an enclosed area, such as a tunnel or a trench,

unless adequate ventilation is provided through such items as exhaust fans or

hoses.

Labels PD 2A / PD 3A

16 wc_si000392gb.fm

2 Labels

2.1 Label Locations

wc_gr007188

E

F

A

C

J

K

G

D

I

BL

PD 2A / PD 3A Labels

wc_si000392gb.fm 17

2.2 Label Meanings

ADANGER!

Asphyxiation hazard.

 Engines emit carbon monoxide.

 Do not run the machine indoors or in an

enclosed area.

 NEVER use inside a home or garage,

EVEN IF doors and windows are open.

 Only use OUTSIDE and far away from

windows, doors, and vents.

 Read the Operator’s Manual.

 No sparks, flames, or burning objects near

the machine.

 Stop the engine before refueling.

B NOTICE

Lifting point.

CCAUTION!

Grease connecting rod bearing monthly.

Read the Operator’s Manual.

AVISO

AVIS

HINWEIS

Labels PD 2A / PD 3A

18 wc_si000392gb.fm

D WARNING!

Pinch point! Do not operate without safety

guards. Read and understand the Operator’s

Manual.

ECAUTION!

Read and understand the supplied

Operator’s Manual before operating this

machine. Failure to do so increases the risk

of injury to yourself and others.

F WARNING!

Hot surface

G Guaranteed sound power level in dB(A).

PD 2A / PD 3A Labels

wc_si000392gb.fm 19

INotice

Do not exceed 60 strokes per minute with the

diaphragm pump.

Read the Operator’s Manual.

J

Notice

Use noncollapsible hose or pipe on

suction side of pump.

Read the Operator’s Manual.

Labels PD 2A / PD 3A

20 wc_si000392gb.fm

K WARNING!

Never pump volatile, flammable, or low-

flash-point fluids. These fluids could ignite or

explode.

Read the Operator’s Manual.

La page est en cours de chargement...

Wacker Neuson PDT2A Manuel utilisateur

Ce manuel convient également à

Wacker Neuson PDT2A Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents