Hansong(Nanjing) Technology Crescendo X Manuel utilisateur

Marque: Hansong(Nanjing) Technology

Modèle: Crescendo X

Catégorie: Équipement musical supplémentaire

Taper: Manuel utilisateur

Ce manuel convient également à

XCO-CRESCENDOX

user’s manual

IMPORTANT SAFETY INSTRUCTIONS!

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in accordance with the manu-

facturer’s instructions.

8 Do not install near any heat sources such as radiators, heat registers, stoves,

or other apparatus (including amplifiers) that produce heat.

9 Do not defeat the safety purpose of the polarized or grounding-type plug. A

polarized plug has two blades with one wider than the other. A grounding

type plug has two blades and a third grounding prong. The wide blade or

the third prong are provided for your safety. If the provided plug does not fit

into your outlet, consult an electrician for replacement of the obsolete outlet.

10 Protect the power cord from being walked on or pinched, particularly at

plugs, convenience receptacles, and the point where they exit from the

apparatus.

11 Only use attachments/accessories specified by the manufacturer.

12 Use only with the cart, stand, tripod, bracket, or

table specified by the manufacturer, or sold with

the apparatus. When a cart is used, use caution

when moving the cart/apparatus combination to

avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or

when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when

the apparatus has been damaged in any way, such as power-supply cord

or plug is damaged, liquid has been spilled or objects have fallen into the

apparatus, the apparatus has been exposed to rain or moisture, does not

operate normally, or has been dropped.

15. To completely disconnect this equipment from the AC mains, disconnect the

power supply cord plug from the AC receptacle.

16. The mains plug of the power supply cord shall remain readily operable.

17 CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only

with the same or equivalent type (AAA). Dispose of dead batteries in accor-

dance with local regulation.

18. To prevent overheating, do not cover the apparatus. Install in accordance

with the manufacturer’s instructions.

19. No naked flame sources, such as candles, should be placed on the product.

20. Do not expose this apparatus to dripping or splashing and ensure that no

objects filled with liquids, such as vases, are placed on the apparatus.

21. Batteries (battery pack or batteries installed) shall not be exposed to exces-

sive heat such as sunshine, fire, or the like.

22. For apparatus mounted to wall, the apparatus shall be installed on solid

wood, bricks, concrete or solid wood columns and battens.

23. DO NOT overload wall outlets or extension cords beyond their rated capacity

as this can cause electric shock or fire.

24. Minimum distances around the apparatus for sufficient ventilation.

25. The ventilation should not be impeded by covering the ventilation openings

with items, such as newspapers, tablecloths,curtains, etc.

26. Do not ingest the battery, Chemical Burn Hazard.

27. Keep new and used batteries away from children.

28. If the battery compartment does not close securely, stop using the product

and keep it away from children.

29. If you think batteries might have been swallowed or placed inside any part of

the body, seek immediate medical attention.

30. The battery (battery or batteries or battery pack) shall not be exposed to

excessive heat such as sunshine, fire or the like.

31. Risk of leakage. Only use the specified type of Batteries. Never mix new and

used batteries. Observe correct polarity. Remove batteries from products that

are not in use for extended periods of time. Store batteries in a dry place.

32. Do not recharge non-rechargeable batteries.

33. Avoid exposure to extreme heat or cold.

34. This equipment is a Class II or double insulated electrical appli-

ance. It has been designed in such a way that it does not require

a safety connection to electrical earth.

35. Danger of explosion if battery is incorrectly replaced. Replace only with the

same or equivalent type.

36. (The remote control supplied with) This product contains a AAA battery. If the

AAA battery is swallowed, it can cause severe internal burns in just 2 hours

and can lead to death.

37. Do not handle leaking or damaged AAA batteries.

The lightning bolt flash with arrowhead

symbol within an equilateral triangle,

is intended to alert the user to the pres-

ence of potentially “dangerous voltage” within the

product’s enclosure that may be of sufficient magni-

tude to constitute a risk of electric shock to persons.

The exclamation point within an equi-

lateral triangle is intended to alert the

user to the presence of important oper-

ating and maintenance (servicing) instructions in the

literature accompanying the appliance.

Do Not Open! Risk of Electrical Shock. Voltages in this equip-

ment are hazardous to life. No user-serviceable parts inside.

Refer all servicing to qualified service personnel. To prevent fire

or shock hazard, do not expose this module to rain or moisture.

38. THIS PRODUCT CONTAINS A AAA BATTERY. IF MISUSED OR ABUSED THIS

CAN RESULT IN:

- Smoke or gas hazard

- Heat hazard

- Fire hazard

- Explosion hazard

39. If an appliance coupler is used as the disconnect device, the disconnect

device shall remain readily operable.

The rating for the USB output is 5V

2.1A.

WARNING: This product is intended to be operated ONLY from the AC Voltages

listed on the back panel or included power supply of the product. Operation from other

voltages other than those indicated may cause irreversible damage to the product

and void the product warranty. The use of AC Plug Adapters is cautioned because

it can allow the product to be plugged into voltages in which the product was not

designed to operate. If the product is equipped with a detachable power cord, use

only the type provided with your product or by your local distributor and/or retailer. If

you are unsure of the correct operational voltage, please contact your local distributor

and/or retailer.

This device complies with Part 15 of the FCC Rules. Operation is subject to the follow-

ing two conditions: (1) This device may not cause harmful interference, and (2) this

device must accept any interference received, including interference that may cause

undesired operation.

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE

STATEMENT: This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interfer-

ence will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one

or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Approved under the verification provision of FCC Part 15 as a Class B Digital Device.

Any changes or modifications not expressly approved by the grantee of this device

could void the user’s authority to operate the equipment.

RF EXPOSURE WARNING: This equipment must be installed and operated in

accordance with provided instructions and the antenna(s) used for this transmitter

must be installed to provide a separation distance of at least 20 cm from all per-

sons and must not be co-located or operating in conjunction with any other antenna

or transmitter. End-users and installers must be provide with antenna installation

instructions and transmitter operating conditions for satisfying RF exposure compli-

ance.

5GHz RF DEVICE STATEMENT: This device operates in the 5.15–5.25GHz

frequency range and is restricted to indoor use only. Outdoor operations in the 5150–

5250MHz frequency range is prohibited.

CANADA, INDUSTRY CANADA (IC) NOTICES: This device complies with

Industry Canada licence-exempt RSS standard(s). Operation is subject to the following

two conditions: (1) this device may not cause interference, and (2) this device must

accept any interference, including interference that may cause undesired operation

of the device.

Under Industry Canada regulations, this radio transmitter may only operate using

an antenna of a type and maximum (or lesser) gain approved for the transmitter by

Industry Canada. To reduce potential radio interference to other users, the antenna

type and its gain should be so chosen that the equivalent isotropically radiated power

(e.i.r.p.) is not more than that necessary for successful communication.

This radio transmitter (certification number: 7756A-CRESCENDOX) has been approved

by Industry Canada to operate with the antenna types listed below with the maximum

permissible gain and required antenna impedance for each antenna type indicated.

Antenna types not included in this list, having a gain greater than the maximum gain

indicated for that type, are strictly prohibited for use with this device.

Gain of antenna: 4.2dBi max.

Type of antenna: 50ohm, PIFA

RADIO FREQUENCY (RF) EXPOSURE INFORMATION: The radiated output

power of the Wireless product is below the Industry Canada (IC) radio frequency

exposure limits. The Wireless product should be used in such a manner such that the

potential for human contact during normal operation is minimized. This device has

also been evaluated and shown compliant with the IC RF Exposure limits under mobile

exposure conditions. (antennas are greater than 20cm from a person’s body).

Caution: (i) The device operating in the band 5150–5250 MHz is only for indoor use

to reduce the potential for harmful interference to co-channel mobile satellite systems;

(ii) The maximum antenna gain permitted for devices in the bands 5250–5350 MHz

and 5470–5725 MHz shall comply with the e.i.r.p. limit; and (iii) The maximum

antenna gain permitted for devices in the band 5725–5825 MHz shall comply with

the e.i.r.p. limits specified for point-to-point and non point-to-point operation as

appropriate. (iv) Users should also be advised that high-power radars are allocated

as primary users (i.e. priority users) of the bands 5250–5350 MHz and 5650–5850

MHz and that these radars could cause interference and/or damage to LE-LAN devices.

(iv) the worst-case tilt angle(s) is compliant with the e.i.r.p. elevation mask require-

ment set forth in Section 6.2.2(3).

WEEE NOTICE

Note: This mark applies only to countries within the European

Union (EU) and Norway.

In accordance with the European Union WEEE (Waste Electrical and Electronic

Equipment) directive 2002/96/EC effective August 13, 2005, we would like to

notify you that this product may contain regulated materials which upon disposal,

according to the WEEE directive, require special reuse and recycling processing.

For this reason Martin Logan has arranged with our distributors in European

Union member nations to collect and recycle this product at no cost to you.

find your local distributor please contact the dealer from whom you purchased

this product, email [email protected] or visit the distributor locator at

www.martinlogan.com.

Please note, only this product itself falls under the WEEE directive. When dis-

posing of packaging and other related shipping materials we encourage you to

recycle these items through the normal channels.

WARNING/CAUTION!

• Hazardous voltages exist inside—do not remove cover.

• Refer servicing to a qualified technician.

• To prevent fire or shock hazard, do not expose this module to moisture.

• Unplug speaker should any abnormal conditions occur.

• Turn speaker off before making or breaking any signal connections!

• The power cord should not be installed, removed, or left detached from the

speaker while the other end is connected to an AC power source.

• No candles or other sources of open flame should be placed on the speaker.

• No liquids either in glasses or vases should be placed on speaker.

• Speaker should not be exposed to dripping or splashing liquids.

• The terminals marked with the lightning bolt symbol should be connected by

an instructed person or by way of ready made terminals.

• The power cord should remain readily operable should any abnormal

conditions occur.

• Any changes or modifications not expressly approved by the grantee of this

device could void the user’s authority to operate the equipment.

AirPlay, iPad, iPhone, iPod, iPod classic, iPod nano, and iPod touch are

trademarks of Apple Inc., registered in the U.S. and other countries.

AirPlay works with iPhone, iPad, and iPod touch with iOS 4.3.3 or later,

Mac with OS X Mountain Lion, and Mac and PC with iTunes 10.2.2 or later.

iPad mini, iPod touch (3rd through 5th generation), and iPod nano (5th

through 7th generation). “Made for iPod,” “Made for iPhone,” and “Made

for iPad” mean that an electronic accessory has been designed to connect

specifically to iPod, iPhone, or iPad, respectively, and has been certified by

the developer to meet Apple performance standards. Apple is not respon-

sible for the operation of this device or its compliance with safety and

regulatory standards. Please note that the use of this accessory with iPod,

iPhone, or iPad may affect wireless performance.

Made for:

• iPhone 6 Plus

• iPhone 6

• iPhone 5s

• iPhone 5c

• iPad Air 2

• iPad mini 3

For DTS patents, see http://patents.dts.com. Manufactured under license

from DTS, Inc. DTS, Play-Fi, the Symbol, and Play-Fi together in combi-

nation with the Symbol are trademarks of DTS, Inc. DTS and Play-Fi are

Apple and the Apple logo are trademarks of Apple Inc., registered in the U.S.

and other countries. App Store is a service mark of Apple Inc.

The Spotify software is subject to third party licenses found here:

www.spotify.com/connect/third-party-licenses

The Bluetooth word mark and logos are registered trademarks owned by

Bluetooth SIG, Inc. and any use of such marks by MartinLogan, Ltd. is under

license.

Windows is a registered trademark of Microsoft Corporation in the United

States and other countries.

Other trademarks and trade names are those of their respective owners.

Introduction and Overview ...............7

Placement ...........................7

Connection ..........................7

Power Connection ...................7

Signal Connection ...................7

Network Connection .................8

Subwoofer Connection ................8

An Overview of Connections .............9

Volume Behavior by Input ...............9

Controls ...........................11

Front Panel Controls .................11

Remote Control ....................12

Changing the Remote’s Batteries .........12

Control Functions by Input ..............13

Playing Audio Using Play-Fi

............13

Automatic Input Selection ..............13

Playback – From the DTS Play-Fi App ......13

Controlling Multiple Speakers ...........14

Additional Play-Fi Features .............14

Playing Audio Using AirPlay

............14

Automatic Input Selection ..............14

Playback – From an Apple

iOS Device ....14

Playback – From iTunes

on a Mac or PC ..14

Controlling Playback Using iTunes ........15

How to use Connect ...................15

DTS Play-Fi and Apple AirPlay Setup ......15

Network Requirements ...............15

DTS Play-Fi App Requirements ...........15

Apple AirPlay Requirements ............16

Wi-Fi Status Light ...................16

Downloading the DTS Play-Fi App ........16

Connecting to a Wireless Network:

Access Point Setup .................16

Audio Streaming Usage Guide ..........16

Connecting to a Wireless Network:

Wi-Fi Protected Setup (WPS) ..........18

Connecting to a Wired Network ........18

Apple AirPlay Setup (Without DTS App) ....18

Bluetooth

Connection .................19

Updates and Rebooting ................20

DTS Play-Fi App Update ..............20

DTS Play-Fi Module Update ............20

MartinLogan Firmware Update ..........20

Rebooting ........................20

Factory Reset ......................20

Removing the Front Grille ...............20

Contacting Customer Service ............20

General Information ..................20

Warranty Information ................20

Serial Number .....................21

Service .........................21

Frequently Asked Questions .............21

Troubleshooting ...................... 22

Specifications .......................24

Dimensional Drawings .................25

Serial Number:_____________________________

Record your serial number here for easy reference.

You will need this information when filling out your

warranty registration. The serial number is located on

the back of the speaker and on the product carton.

IntroductIon and overvIew

Placement

Thank you—the MartinLogan owner, for loving what we

do, and making it possible for us to do what we love.

MartinLogan’s dedicated in-house engineering and

design team developed the Crescendo X speaker to

deliver exceptional audio performance from a single

system, easily integrated and installed in a diverse

variety of environments. The Crescendo X produces an

enveloping field of richly detailed audio incorporating

two tweeters (featuring MartinLogan’s award-winning

Folded Motion technology), a high-performance woofer,

and three channels of dedicated class-D amplification

representing 100 watts of total system power.

An advanced 24-bit 48kHz DSP (digital signal pro-

cessing) based pre-amplifier allows MartinLogan to

replace dedicated stereo speakers with a one piece

solution, capable of reproducing sound with unflinch-

ing accuracy, resolution, and detail—the inspiration

behind every MartinLogan design. Additionally, for

a fully authentic audio experience, the Crescendo X

makes connecting a dedicated subwoofer as simple

as the push of a button.

The Crescendo X’s remote control quickly adjusts

volume, selects inputs, and controls your media. The

remote also allows you to easily switch between

two discrete acoustic modes—‘Bass +’ mode (for

those moments requiring a little extra thunder) and a

‘Normal’ mode that restores normal levels.

We recommend locating the speaker on a surface

that provides a wide, level, and stable platform

such as a table or audio/video rack. Please note,

this speaker is not magnetically shielded and there-

fore should not be placed directly beneath or on

top of a CRT (cathode ray tube) television. The

magnetic field of the speaker will not affect plasma

and LCD style televisions.

connectIon

POWER CONNECTION

The power cord should be firmly inserted into the

AC power receptacle on the rear of the speaker,

and then to any convenient AC wall outlet.

If you remove your speaker from the country of

original sale, be certain that the AC power sup-

plied in any subsequent location is suitable

before connecting and operating the speaker.

Substantially impaired performance or severe

damage may occur to the speaker if operation is

attempted from an incorrect AC power source.

When the Power button on the back panel is set

to ‘Off’ the speaker is completely powered down,

including all network connections (Wi-Fi and

Ethernet are deactivated).

SIGNAL CONNECTION

Connections are made at the signal input section

WARNING! Turn your speaker off

before making or breaking any sig-

nal connections! WARNING! The

power cord should not be installed,

removed, or left detached from the speaker while

the other end is connected to an AC power source.

on the rear electronics panel of the speaker. Your

speaker features the following audio inputs:

• Ethernet: used for streaming audio from Apple

AirPlay or DTS Play-Fi

• Aux [Auxiliary]: used for either digital optical

(Toslink) or analog input. This input will accept

either a standard 3.5mm stereo headphone

style or mini-Toslink plug. A special mini-Tos-

link to Toslink cable or mini-Toslink adaptor is

required for digital optical connection.

In addition, the speaker features two inputs that do

not require a physical connection:

• Wireless: used for streaming audio from Apple

AirPlay or Play-Fi

• Bluetooth: used for streaming from compatible

Bluetooth equipped devices, including aptX

Bluetooth devices.

Please note, when utilizing this speaker to reproduce

audio from a television via the speaker’s Auxiliary

(digital or analog) connection, the television’s audio

output should be defeated. Some televisions will

allow you to turn off the internal speaker via the

television’s menu system. Other televisions may

require you to turn the television’s volume to “zero”

or “mute.” Additionally, your television may require

you to turn on the digital optical output or and/or

configure the output for 2-channel (stereo) sound.

Please refer to your television’s manual.

NETWORK CONNECTION

To stream audio to your speaker, a LAN (local

area network) connection is required. This connec-

tion can be established using Wi-Fi or Ethernet.

Refer to the wireless setup section of this manual for

setup and usage details.

SUBWOOFER CONNECTION

You may choose to employ a separate subwoofer

to enhance bass performance. Subwoofers can

be connected via the speaker’s “Sub Out” RCA

connection. We recommend using a superb

MartinLogan subwoofer.

Using a high-quality RCA style cable designed for

subwoofer connection, connect “Sub Out” from the

speaker to the “LFE In/Sub In” on the subwoofer.

On the back panel of the speaker, set the Sub

Out button to “On” (in its “on” state the button will

be depressed—in its “off” state the button will be

extended). When the Sub Out is turned on, the

deep bass output of the speaker will be reduced

(to optimize performance) and bass information will

be sent directly to your external subwoofer for a

deeper, extended, overall bass response.

Reference your subwoofer’s manual to learn how

to properly adjust the sub’s level and phase con-

trols to achieve proper blending with the speaker.

When Sub Out is set to “On,” the speaker will

handle the crossover setting to the subwoofer,

Fig. 1 Connection Panel

achieving ideal blending with the speaker.

Because of this, the subwoofer’s crossover should

be set to “bypass” or “LFE.” For subwoofers that

do not have a “bypass” or “LFE” crossover setting,

we recommend adjusting the crossover to its high-

est setting—remember, the speaker will handle the

crossover before sending out the sub signal.

Using a MartinLogan Dynamo Subwoofer:

If using a MartinLogan Dynamo family subwoofer,

we recommend beginning with the following sub-

woofer settings:

• Low-pass: Bypass

• Phase: 0

• Volume: Knob set to vertical (12-o’clock to

1-o’clock position)

Digital Optical: Also referred to as Toslink, this cable utilizes one cable to pass digital

audio information (no video). A digital optical cable offers a high-quality digital

connection and passes multi-channel encoded audio between a source compo-

nent and an audio output device. The Auxiliary input on this speaker accepts

digital optical connection with the use of a mini-Toslink adaptor (included with

this speaker). Toslink to mini-Toslink cables may also be available from your dealer.

Left/Right Analog RCA: These cables are used to pass audio information (no

video). An analog RCA cable can only pass a single channel of audio infor-

mation between a source component and audio output device. To achieve

two-channels of audio (left/right), you will find that analog RCA cables come

bundled as a stereo pair (two connectors on each end). The Auxiliary input

on this speaker can accept an analog stereo signal through a cable using a

3.5mm stereo “headphone style” jack. If you are connecting this speaker to a device (such as a dock

or CD player) with left/right RCA analog outputs, you will need a special cable with a 3.5mm ‘head-

phone style’ jack on one end and left/right RCA jacks on the other end.

Left/Right Analog 3.5mm Stereo “Headphone Style” Jack: This cable is used to pass

audio information (no video). Users may find source components such as digital

media players and docks utilize a 3.5mm ‘headphone style’ connector. The

Auxiliary input on this speaker can accept an analog stereo signal through a

cable using a 3.5mm “headphone style” connector. These devices also have a

“volume control” that increases or decreases the level of the output signal.

If you are connecting a device

which allows volume adjustment (like a digital media player or cell phone), we recommend the volume on

the device not be set to maximum. When the volume is set to its maximum setting, the amplifier in the external

device is likely to introduce elevated distortion into the audio signal which, in turn, will be passed on to this

speaker and further amplified, creating even more distortion.

an overvIew of connectIons

an overvIew of connectIons [contInued]

Ethernet: This cable allows you to physically connect a device to a LAN (local area

network). When connected to a LAN, audio information can be sent to this

speaker using various protocols (such as Play-Fi

or AirPlay). If a wireless (Wi-

Fi) connection is used to connect to a LAN, there is no need to use an

Ethernet connection. However, in some installations, a ‘hard-wired’ Ethernet

connection may prove more desirable than a wireless connection.

Wi-Fi: This connection technology wirelessly connects a device to a LAN (local area

network). When connected to a LAN, audio information can be sent to this speaker using

various protocols (such as Play-Fi or AirPlay). If an Ethernet connection is used to connect

to a LAN, there is no need to use a Wi-Fi connection. In some installations a ‘hard-wired’ Ethernet

connection may prove more desirable than a wireless connection.

Bluetooth: This wireless connection technology allows a wide variety of devices to connect

to an audio output device and stream audio. Bluetooth establishes a connection directly

with an audio output device and does not require either device to be connected to a LAN.

volume BehavIor By InPut

Depending on the input selected on your speaker, the volume will exhibit different behaviors.

SPEAKER INPUT FRONT LED COLOR VOLUME BEHAVIOR

Wireless or Ethernet

(using AirPlay or Play-Fi)

Purple (flashing purple indicates

no network is available)

Volume on device/remote and speaker

are synced and control each other.

Aux [Auxiliary]

Green

Volume on device/remote and volume

on speaker are controlled separately.*

Bluetooth

Blue

Volume on device/remote and volume

on speaker are controlled separately.*

* Devices connected via auxiliary and Bluetooth will often have

their own volume control which functions separately from the

speaker’s volume. If you are connecting a device which allows

you to adjust its volume separately, we recommend that the

volume on the device not be set to maximum. When set to its

maximum setting, the amplifier in the external device is likely to in

troduce elevated levels of distortion into the audio signal which,

in turn, will be further amplified by the speaker. Find a volume be

tween 50–75% of the device’s maximum volume and use your

speaker’s volume control to adjust the final playback volume.

controls

FRONT PANEL CONTROLS

STANDBY/MUTE: This button mutes the speak-

er and toggles between on and standby. To

mute press the button once (front LED will flash red). To

enter standby press the button for two seconds (front LED

will turn red). If no audio signal is detected for ten min-

utes, the speaker will automatically go into networked

standby mode (Wi-Fi and Ethernet remain active).

When the speaker is in standby mode, press the button

once to exit. A new audio signal will also automatically

wake the speaker. Please note, if the Auxiliary Input

has a cable plugged into the connection (with or with-

out active audio content), the speaker will not go into

standby mode automatically and will not stay in standby

mode, even if manually activated (fig. 2).

INPUT: Cycles through the audio inputs.

The order of the inputs is:

Wireless/Ethernet (purple) > Auxiliary (green) >

Bluetooth (blue) (fig. 2).

FRONT LED: The LED on front of the speaker indi-

cates the following (fig. 2):

• No Color: Speaker does not have power (or

updating firmware).

• Red: Speaker is in standby.

• Flashing Red: Speaker is muted.

• Purple: Wireless/Ethernet input active.

• Flashing Purple: Wireless/Ethernet input active

(no network connected).

• Green: Auxiliary input active.

• Blue: Bluetooth input active.

VOL –/VOL +: Adjusts the volume

level (fig. 2). For more details see

the section titled “VOLUME BEHAVIOR BY INPUT.”

STANDBY/MUTE INPUT VOL– VOL+FRONT LED

Fig. 2 Front Panel Controls

REMOTE CONTROL

STANDBY: This button toggles between on and stand-

by. If no audio signal is detected for ten minutes, the

speaker will automatically go into networked standby

mode (Wi-Fi and Ethernet remain active). When the

speaker is in standby mode, press the button once

to exit. A new audio signal will also automatically

wake the speaker. Please note, if the Auxiliary Input

has a cable plugged into the connection (with or

without active audio content), the speaker will not go

into standby mode automatically and will not stay in

standby mode, even if manually activated.

MUTE: Mutes the volume. A second press will restore

the previous volume setting. Additionally, you can

turn mute off by pressing either of the volume buttons.

When mute is active, the front LED will blink red.

VOL+/VOL–: Adjusts volume level. See the section

titled “VOLUME CONTROL (BY INPUT)”

PLAY/PAUSE: Toggles between play or pause.

This button works when a source is connected via

AirPlay or Play-Fi.

BASS MODE – NORMAL: Normal bass levels.

BASS MODE – BASS+: Increases bass output.

INPUT – WIRELESS/ETHERNET: Sets the current

input to receive an audio signal from the local

area network via the Wi-Fi or Ethernet connection

(using AirPlay or Play-Fi

INPUT – AUXILIARY: Sets the current input to

receive an audio signal from the auxiliary input via

a digital optical mini Toslink or analog 3.5mm ste-

reo “headphone” style jack connection.

INPUT – BLUETOOTH: Sets the current input to

receive an audio signal from a Bluetooth capable

device that is connected wirelessly to the speaker.

Turn turn Bluetooth on, press the input button to

switch the source to Bluetooth. To turn Bluetooth

off, select an input other than Bluetooth.

CHANGING THE REMOTE’S BATTERIES

The remote control for your speaker uses two AAA

type batteries. Access the battery compartment by

using a Phillips screwdriver to remove the screw

located on the bottom of the remote.

Fig. 3 Remote Control

Caution! Danger of explosion

if battery is incorrectly replaced.

Replace only with the same or

equivalent type.

Play-Fi

AirPlay iTunes Digital or Analog Bluetooth

Speaker Input

Wireless/

Ethernet

Wireless/

Ethernet

Wireless/

Ethernet

Auxiliary Bluetooth

Front LED Color

Purple Purple Purple Green Blue

Standby

√ √ √ √ √

Mute

√ √ √ √ √

Volume –/+

√ √ √ √* √*

Play/Pause

√ √ √

Bass Mode:

Normal

√ √ √ √ √

Bass Mode:

Bass +

√ √ √ √ √

Input: Wireless/

Ethernet

√ √ √ √ √

Input: Auxiliary

√ √ √ √ √

Input: Bluetooth

√ √ √ √ √

*Devices connected via auxiliary and Bluetooth will

often have their own volume control which is separate

from the speaker’s volume. If you are connecting a

device which allows you to adjust its volume separately,

we recommend that the volume on the device not be

set to maximum. When set to its maximum setting, the

amplifier in the external device is likely to introduce

elevated levels of distortion into the audio signal which,

in turn, will be further amplified by the speaker. Find

a volume between 50-–75% of the device’s maximum

volume and use your speaker’s volume control to adjust

the final playback volume.

Depending on the input selected on your speaker, the remote will control functions differently.

control functIons By InPut

PlayIng audIo usIng Play‑fI

AUTOMATIC INPUT SELECTION

Your speaker will automatically switch to the

streaming input if it detects that a new Play-Fi con-

nection has been established with the speaker.

PLAYBACK – FROM THE DTS PLAY-FI APP

Note: Future updates to the DTS Play-Fi application

may change functionality.

1. Launch the DTS Play-Fi app on your mobile

device or PC (located in the system tray).

2. Android™ and iOS Device Users: Within the

Play-Fi app, select your music source. You can

choose from your personal music library, Internet

Radio, or from select internet music services. PC

Users: Any audio content from your computer

can be streamed using Play-Fi.

If you have more than one DTS Play-Fi

speaker

connected to your network, you will be prompted

to select the speaker to which you want to stream.

CONTROLLING MULTIPLE SPEAKERS

If you have more than one Play-Fi speaker connect-

ed to your network, you can simultaneously stream

the same audio to multiple speakers.

1. Android and iOS Device Users: Within the

app, press the Play-Fi logo in the lower corner

of the app. PC Users: open the Play-Fi program

using the icon in your system tray.

Select additional devices to play audio from. PC

Users: The free version of the Windows

app

may not allow streaming to multiple speakers. An

upgraded version of the DTS Play-Fi app, with this

capability, can be purchased from the DTS website.

Note: 8 Play-Fi speakers can be synced to

play the same audio content at the same time.

We recommend up to 32 Play-Fi speakers on

a network for the best experience, but the only

limit to connected devices is how many your

router can support.

TIP! Primary and Secondary Speakers

When streaming audio content to multiple devices,

you will be asked to assign them to two categories:

primary and secondary devices. The DTS Play-Fi

module requires a primary device be selected.

This maximizes synchronization between multiple

devices simultaneously streaming the same content.

Select the DTS Play-Fi

device with the strongest signal

as your primary device. Secondary devices connect

to your primary device, so if you disable your primary

device, you will need to select a new primary device

before audio resumes on your secondary devices.

ADDITIONAL PLAY-FI FEATURES

New versions of the Play-Fi app will add features

not mentioned in this manual. Please refer to the

app and related documentation for details on new

and enhanced features such as streaming different

audio content to multiple zones and grouping of two

discrete speakers for stereo (left/right) playback.

AUTOMATIC INPUT SELECTION

Your speaker will automatically switch to the

streaming input if it detects that a new AirPlay con-

nection has been established with the speaker.

PLAYBACK – FROM AN APPLE iOS DEVICE

1. Open your music application.

2. Press the AirPlay icon and choose your speaker

from the list.

3. Play music.

PLAYBACK – FROM iTUNES ON A MAC

OR PC (PERSONAL COMPUTER)

1. Launch iTunes (version 10 or later).

2. Click the AirPlay icon (usually located in the

upper left of the iTunes window) and choose

your speaker from the list. You can choose

multiple speakers if you have more than one

speaker on your network.

3. Play music.

PlayIng audIo usIng aIrPlay

CONTROLLING PLAYBACK USING iTUNES

To control playback (play/pause/volume) from

your speaker or remote control, follow these steps:

1. On your computer, launch iTunes (version

10.2.2 or later).

2. Open “Preferences” and choose “Devices.”

3. Check the box for “Allow iTunes audio control

from remote speakers” and click okay.

dts Play‑fI

and aPPle aIrPlay setuP

NETWORK REQUIREMENTS

You must have the following to connect your wireless

product to your network:

• A wireless router.

• A high-speed internet connection for reliable

playback of internet based music services.

• Have your network password ready before

connecting the wireless product to your network.

TIP! If wireless connectivity is weak or not available,

connect to your router with an Ethernet cable. TIP! Your

wireless product communicates with wireless networks

that support 802.11g/n. For best performance, a

network that supports 802.11n wireless technology is

recommended. A network supporting 802.11b may be

used, but it will effectively stream to only one device

equipped with DTS Play-Fi. Your wireless product

communicates over a 2.4 GHz wireless band, however,

it can become slow in locations, such as apartments,

where many routers are in operation. Consequently,

your wireless product is capable of jumping onto a 5

GHz band on dual band wireless routers.

DTS PLAY-FI APP REQUIREMENTS

• An Android device running Android 2.2 or later.

• An iOS device running iOS 6.0 or later.

• A Windows

PC running Windows 7, 8 (32 and

64 bit), or later.

You’ll need Spotify Premium to use Connect, see

details overleaf.

1. Add your new device to the same wifi network

as your phone, tablet or PC (see product user

instructions for details).

2. Open the Spotify app on your phone, tablet or

PC, and play any song.

3. If you’re using the app on a phone - tap the

song image in the bottom left of the screen. For

tablet and PC move to step 4.

4. Tap the Connect icon

5. Pick your device from the list. If you can’t see

it, just check it’s connected to the same wifi

network as your phone, tablet or PC.

All done! Happy listening.

Licenses

The Spotify Software is subject to third party

licenses found here:

www.spotify.com/connect/third-party-licenses.

how to use connect

audIo streamIng usage guIde

DEVICE APP CONTENT MULTI-ROOM SUPPORT

Apple iOS

DTS Play-Fi

• Select music services

• iTunes music stored on device

• Up to eight

• Multiple simultaneous users

• Speakers can be zoned

Apple AirPlay

• iTunes audio content

• All iOS music apps

• One to one

Android

DTS Play-Fi

• Select music services

• iTunes music stored on device

• Up to eight

• Multiple simultaneous users

• Speakers can be zoned

Mac PC

Apple AirPlay

• All audio content • Up to six

Windows PC

DTS Play-Fi

• All audio content

• Up to eight

• Multiple simultaneous users

• Speakers can be zoned

Apple AirPlay

• iTunes audio content • Up to six

APPLE AIRPLAY REQUIREMENTS

• An iOS device running iOS 4.3.3 or later.

• Mac with OS X Mountain Lion, or later.

• Mac or PC with iTunes 10.2.2, or later.

WI-FI STATUS LIGHT

The Wi-Fi Status light tells you what your wireless

product is doing (fig. 1 & 2).

• Rapid Blinking: booting up.

• Blinking: connecting to a wireless router.

• Slow Pulse: Access Point Setup Mode.

• Two Blinks & Pause: WPS (Wi-Fi Protected

Setup) Mode.

• Solid: Connected to a wireless router.

• Off: Connected to a router via Ethernet.

DOWNLOADING THE DTS PLAY-FI

APP

•

Android Device Users: Download DTS’s free Play-Fi

app from the Google Play

or Amazon App Store

• iOS Device Users: Download DTS’s free Play-Fi

app from the Apple App Store.

• PC Users: Download DTS’s free Play-Fi program

from https://play-fi.com/apps/windows

TURNING WI-FI ON AND OFF

After powering on the speaker, the default status of

Wi-Fi is on. Press and hold the Standby/Mute and

Vol+ buttons for 3 seconds to turn Wi-Fi off. Press

and hold the Standby/Mute and Vol+ buttons for 3

seconds to turn Wi-Fi back on.

CONNECTING TO A WIRELESS NETWORK:

ACCESS POINT SETUP

Access Point Setup causes your MartinLogan

wireless product to behave as if it were a wireless

router. Using your mobile device or Wi-Fi capable

PC, you connect directly to your wireless product

using Wi-Fi, select your home wireless network,

and enter the network password.

For optimal setup conditions place your wireless

product next to your wireless router. The device

can be moved to its final location after wi-fi setup.

2. Plug in your wireless product and press the

Power button. The Wi-Fi Status light will start

rapidly blinking for about 20 seconds while your

wireless product is booting up. If your wireless

product is not configured to connect to your

network, it will continue to blink. If this is the first

time your new wireless product is plugged in,

the Wi-Fi Status light will start pulsing slowly.

If the wireless product is already configured to

connect to a wi-fi network, the button will turn

solid (connected) or blink rapidly (not connected).

Once the Wi-Fi Status light starts pulsing slowly,

your wireless product is in Access Point Mode and

ready to connect to your wireless network. Note:

If the Wi-Fi Status light does not pulse slowly, press

and hold the Wi-Fi Setup button for 8 seconds.

You will hear two tones—one at 3 seconds and

another at 8 seconds. After 20 seconds, the Wi-

Fi Status light will begin pulsing slowly to indicate

Access Point mode is ready. At anytime you can

press the button again to cancel the setup mode.

Android Device Users:

a) Launch the DTS Play-Fi

app.

b) The app will automatically find your device

and provide prompts for setup.

c) Touch the “Setup” button on the screen.

d) Enter the password for your wireless network;

the app will connect your device to your

network. You will notice the Wi-Fi Status light

will have changed from blinking to solid. This

may take up to a minute. If, after a minute,

the button continues to blink rapidly, setup

failed and you should try again.

e) Your wireless product is now connected to

your wireless network. Reconnect your mobile

device to your wireless network. You may re-

name your device using the app.

iOS Device Users:

Please note: When using an iOS device your

wireless product can stream audio using either

Apple AirPlay or DTS Play-Fi.

a) Make sure your iOS device’s Wi-Fi is turned

on and connected to your Wi-Fi network.

b) Open your iOS device’s ‘Settings’ app

and go to the ‘Wi-Fi’ menu. Your wireless

product will show up under the heading ‘set

up new AirplAy speAker...’

c) Select your wireless product from the list. It

will have “Play-Fi ” in the name.

d) Once in the ‘AirPlay Setup’ menu you will

be prompted to select your Wi-Fi network

and name your speaker (you will not need

to enter your network password.)

e) Once your device is connected, you will

notice that the Wi-Fi Status light on your

wireless product will change from blinking to

solid. This may take up to a minute. If, after a

minute, the button continues to blink rapidly,

setup failed and you should try again.

Your wireless product is now connected to

your wireless network. Reconnect your iOS

device to your wireless network.

PC Users:

a) Launch the DTS Play-Fi app.

b) The app will automatically find your device

and provide prompts for set up. If the app

does not prompt you to set up a new device,

within the app go to the settings screen and

click ‘Setup Play-Fi Device’. Follow the on-

screen instructions.

c) Click the “Set-up” button on the screen.

d) Select the speaker(s) you want to set up.

e) Enter the password for your wireless network;

the app will connect your device to your

network. You will notice the Wi-Fi Status light

will have changed from blinking to solid. This

may take up to a minute. If, after a minute,

the button continues to blink rapidly, setup

failed and you should try again.

Your wireless product is now connected to

your wireless network. Reconnect your PC to

your wireless network. You may re-name your

device using the app.

CONNECTING TO A WIRELESS NETWORK:

WI-FI PROTECTED SETUP (WPS)

Wi-Fi Protected Setup (WPS) is a feature found

on most wireless routers that allows your wireless

product to securely and automatically connect

without needing to enter a password. WPS is not

a standard feature on all routers, and only one

wireless product can be set up at a time.

Check your router’s owner’s manual to see if WPS is

an available feature, or look for a button on your router

marked with the WPS logo ( ). If your router does

not have WPS, then use Access Point Wireless Setup.

1. For optimal setup conditions place your wireless

product next to your wireless router. The device

can be moved to its final location after wi-fi setup.

Plug in your wireless product and press the Power

button. The Wi-Fi Status light will start rapidly blinking

for about 20 seconds while your wireless product is

booting up. If your wireless product is not configured

to connect to your network, it will continue to blink.

If this is the first time your new wireless product is

plugged in, the Wi-Fi Status light will start pulsing

slowly. If the wireless product is already configured

to connect to a wi-fi network, the Status Light will turn

solid (connected) or blink rapidly (not connected).

3. To initiate Wi-Fi Protected Setup (WPS), for 3

seconds, press and hold the Wireless Setup

button on the back of your wireless product until

you hear a tone. The Wi-Fi Status light will blink

twice in continuous intervals to indicate WPS

mode. Now push the WPS button ( ) on your

router. If you cannot find a WPS button on your

router, refer to the router’s owner’s manual.

4. Once the Wi-Fi Status light turns solid (not

blinking), this indicates your wireless product

is connected to your wireless network. If, after

a minute, the button continues to blink rapidly,

setup failed and you should try again.

5. Connect your mobile device or PC to the same

network as your wireless product.

Launch the DTS

Play-Fi

app. Upon launching, it will automatically

detect your wireless product and should prompt

you to name your wireless product.

CONNECTING TO A WIRED NETWORK

1. Using an Ethernet cable, connect your wireless

product to your router.

2. Plug in your wireless product and press the

Power button. The Wi-Fi Status light will start

rapidly blinking for about 20 seconds while

your wireless product is booting up.

The Wi-Fi Status light turns off when the wireless

product is connected via Ethernet.

4. Connect your mobile device or PC to the same

network as your wireless product.

Launch the DTS

Play-Fi app. Upon launching, it will automatically

detect your wireless product and should prompt

you to name your wireless product.

APPLE AIRPLAY SETUP (WITHOUT DTS

APP)

If you do not want to install and use the DTS Play-Fi

app you can still setup the wireless product to work

with iTunes and AirPlay on your Mac or Windows

PC using the following procedure.

Alternate Connection for Mac and Windows PC:

To avoid a delayed wireless set up, place your

wireless product in close proximity to your router

during wireless set up.

2. Plug in your wireless product and press the

Power button. The Wi-Fi Status light will start

rapidly blinking for about 20 seconds while your

wireless product is booting up. If your wireless

product is not configured to connect to your

network, it will continue to blink. If this is the first

time your new wireless product is plugged in,

the Wi-Fi Status light will start pulsing slowly.

If the wireless product is already configured to

connect to a wi-fi network, the button will turn

solid (connected) or blink rapidly (not connected).

Once the Wi-Fi Status light starts pulsing slowly,

your wireless product is in Access Point Mode and

ready to connect to your wireless network. Note:

If the Wi-Fi Status light does not pulse slowly, press

and hold the Wi-Fi Setup button for 8 seconds.

You will hear two tones—one at 3 seconds and

another at 8 seconds. After 20 seconds, the Wi-

Fi Status light will begin pulsing slowly to indicate

Access Point mode is ready. At anytime you can

press the button again to cancel the setup mode.

4. Ensure that Wi-fi is enabled on your computer.

Go to your computer’s Wi-Fi set up. Select the

Wi-Fi network with “Play-Fi ” in the name.

5. Once your wireless product is selected as the

Wi-Fi network, open your web browser and type

http://192.168.0.1/index.html in the address bar.

You will see a web page from your wireless product.

Click on ‘Set Up’. A list of wireless networks will

be displayed. Click on the wireless network you

wish to connect to.

7. Enter the password for your wireless network

then click ‘Next’.

Enter a name for your wireless product and then

click ‘Next’ to connect your wireless product to

your network.

Your wireless product will attempt to connect to

your network. Once the Wi-Fi Status light turns

solid (not blinking), this indicates your wireless

product is connected to your wireless network.

If the Wi button rapidly blinks, setup failed and

should be tried again.

10. Connect your Mac or PC to the same network

as your wireless product. Open your music

application, press the AirPlay icon, and choose

your speaker from the list.

1 Set your speaker to Bluetooth mode. Use the

speaker’s remote control to select Bluetooth,

or repeatedly press the input button on front of

the speaker until the front LED turns blue.

2 Sync the speaker with your digital media

device or computer. Follow the directions that

came with your device/computer.

3 Within your music application, you may need

to select the speaker as the output device for

playback.

4 You are now ready to stream music to your

speaker

Bluetooth connectIon

MartinLogan customer service is available

Monday–Friday between the hours of 8am–5pm

(central time) by calling (785) 749-0133 or by

emailing [email protected].

contactIng customer servIce

general InformatIon

WARRANTY INFORMATION

Your wireless product is provided with an auto-

matic Limited 90 Day Warranty coverage. You

have the option, at no additional charge, to

receive a Limited 2 Year Warranty coverage. To

obtain the Limited 2 Year Warranty coverage,

please complete registration 30 days of pur-

chase. For your convenience, MartinLogan offers

online warranty registration at www.martinlogan.

com. MartinLogan may not honor warranty service

claims unless we have a completed Warranty

Registration on file! Please save your original

purchase receipt. A copy of your reciept may be

required if service is necessary.

DTS PLAY-FI

APP UPDATE

If the DTS Play-Fi app on your mobile device or PC

requires an update, you will be notified that an update

is available and guided through the update process.

DTS PLAY-FI MODULE UPDATE

The DTS Play-Fi module within your speaker will

occasionally require an update. If an update is

needed, the DTS Play-Fi app will notify you and

guide you through the update process.

MARTINLOGAN FIRMWARE UPDATE

Your wireless product may occasionally require

firmware updates. Check www.martinlogan.com

for the latest updates.

REBOOTING

For less than 3 seconds, insert a pin or other small

object into the small hole above the “Reset” label

on back of the speaker. A single tone will sound.

This will reboot your wireless product. Network set-

tings will not be cleared.

FACTORY RESET

For 3 seconds or longer, insert a pin or other small

object into the small hole above the “Reset” label

on back of the speaker. Two tones will sound. This

will reset your wireless product to factory settings

and clear the network configuration.

To remove the front grille from the speaker use a

finger to firmly apply pressure to either corner of

the grille.

removIng the front grIlle

Fig. 4

uPdates and reBootIng

La page charge ...

Hansong(Nanjing) Technology Crescendo X Manuel utilisateur

Marque: Hansong(Nanjing) Technology

Modèle: Crescendo X

Catégorie: Équipement musical supplémentaire

Taper: Manuel utilisateur

Ce manuel convient également à

XCO-CRESCENDOX

Télécharger le PDF

rapport

dans d''autres langues

English: Hansong(Nanjing) Technology Crescendo X User manual

Hansong(Nanjing) Technology Crescendo X Manuel utilisateur

Ce manuel convient également à

Hansong(Nanjing) Technology Crescendo X Manuel utilisateur

dans d''autres langues

Autres documents