MartinLogan Cadence Manuel utilisateur

user’s manual

2

IMPORTANT SAFETY INSTRUCTIONS!

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufac-

turer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or

other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A

polarized plug has two blades with one wider than the other. A grounding type

plug has two blades and a third grounding prong. The wide blade or the third

prong are provided for your safety. If the provided plug does not fit into your

outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched, particularly at plugs,

convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or

table specified by the manufacturer, or sold with

the apparatus. When a cart is used, use caution

when moving the cart/apparatus combination to

avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods

of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the

apparatus has been damaged in any way, such as power-supply cord or plug is

damaged, liquid has been spilled or objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture, does not operate normally, or

has been dropped.

15. To completely disconnect this equipment from the AC mains, disconnect the

power supply cord plug from the AC receptacle.

16. The mains plug of the power supply cord shall remain readily accessible.

17. CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only

with the same or equivalent type (AAA). Dispose of dead batteries in accordance

with local regulation.

18. To prevent overheating, do not cover the apparatus. Install in accordance with

the manufacturer’s instructions.

19. No naked flame sources, such as candles, should be placed on the product.

20. Do not expose this apparatus to dripping or splashing and ensure that no

objects filled with liquids, such as vases, are placed on the apparatus.

21. Batteries (battery pack or batteries installed) shall not be exposed to excessive

heat such as sunshine, fire, or the like.

22. For apparatus mounted to wall, the apparatus shall be installed on solid wood,

bricks, concrete or solid wood columns and battens.

23. DO NOT overload wall outlets or extension cords beyond their rated capacity as

this can cause electric shock or fire.

24. Minimum distances around the apparatus for sufficient ventilation.

25. The ventilation should not be impeded by covering the ventilation openings with

items, such as newspapers, tablecloths, curtains, etc.

26. Do not ingest the battery, Chemical Burn Hazard.

27. Keep new and used batteries away from children.

28. If the battery compartment does not close securely, stop using the product and

keep it away from children.

29. If you think batteries might have been swallowed or placed inside any part of

the body, seek immediate medical attention.

30. The battery (battery or batteries or battery pack) shall not be exposed to exces-

sive heat such as sunshine, fire or the like.

31. Risk of leakage. Only use the specified type of Batteries. Never mix new and

used batteries. Observe correct polarity. Remove batteries from products that are

The lightning bolt flash with arrowhead

symbol within an equilateral triangle, is

intended to alert the user to the presence

of potentially “dangerous voltage” within the product’s

enclosure that may be of sufficient magnitude to consti-

tute a risk of electric shock to persons.

The exclamation point within an equi-

lateral triangle is intended to alert

the user to the presence of important

operating and maintenance (servicing) instructions

in the literature accompanying the appliance.

Do Not Open! Risk of Electrical Shock. Voltages in this equip-

ment are hazardous to life. No user-serviceable parts inside.

Refer all servicing to qualified service personnel. To prevent

fire or shock hazard, do not expose this module to moisture.

CADENCE

Tested to comply with FCC standards.

FOR HOME OR OFFICE USE

3

not in use for extended periods of time. Store batteries in a dry place.

32. Do not recharge non-rechargeable batteries.

33. Avoid exposure to extreme heat or cold.

34. This equipment is a Class II or double insulated electrical appliance.

It has been designed in such a way that it does not require a safety

connection to electrical earth.

35. Danger of explosion if battery is incorrectly replaced. Replace only with the same

or equivalent type.

36. (The remote control supplied with) This product contains a AAA battery. If the

AAA battery is swallowed, it can cause severe internal burns in just 2 hours and

can lead to death.

37. Do not handle leaking or damaged AAA batteries.

38. THIS PRODUCT CONTAINS A AAA BATTERY. IF MISUSED OR ABUSED THIS CAN

RESULT IN:

- Smoke or gas hazard

- Heat hazard

- Fire hazard

- Explosion hazard

WARNING: This product is intended to be operated ONLY from the AC Voltages listed

on the back panel or included power supply of the product. Operation from other voltages

other than those indicated may cause irreversible damage to the product and void the

product warranty. The use of AC Plug Adapters is cautioned because it can allow the

product to be plugged into voltages in which the product was not designed to operate. If

the product is equipped with a detachable power cord, use only the type provided with

your product or by your local distributor and/or retailer. If you are unsure of the correct

operational voltage, please contact your local distributor and/or retailer.

This device complies with Part 15 of the FCC Rules. Operation is subject to the follow-

ing two conditions: (1) This device may not cause harmful interference, and (2) this

device must accept any interference received, including interference that may cause

undesired operation.

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE

STATEMENT: This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interfer-

ence will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one

or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Approved under the verification provision of FCC Part 15 as a Class B Digital Device.

Any changes or modifications not expressly approved by the grantee of this device

could void the user’s authority to operate the equipment.

RF EXPOSURE INFORMATION: This equipment complies with FCC/IC radiation

exposure limits set forth for an uncontrolled environment and meets the FCC radio fre-

quency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio

frequency (RF) Exposure rules. This equipment has very low levels of RF energy that are

deemed to comply without testing of specific absorption ratio (SAR).

2. CAUTION

• comply with FCC RF exposure compliance requirement, separation distance of at

least 20 cm must be maintained between this product and all persons.

• This product and its antenna must not be co-located or operating in conjunction

with any other antenna or transmitter.

• This transmitter must not be co-located or operating in conjunction with any

other antenna or transmitter.

• Operations in the 5.15 - 5.25 GHz band are restricted to indoor usage only.

• For operation within 5.15 - 5.25 GHz / 5.25 - 5.35 GHz / 5.47 - 5.725 GHz

frequency range,it is restricted to indoor environment.

• This device meets all the other requirements specified in Part 15E, Section

15.407 of the FCC Rules.

CONTAINS TRANSMITTER MODULE FCC ID: 2AAWQ-CAPRICA2L

CONTAINS FCC ID : MBBDMRS4

This product complies with Part 15 of the FCC Rules. Operation is subject to the follow-

ing two conditions: (1) this product may not cause harmful interference, and (2) this

product must accept any interference received, including interference that may cause

undesired operation.

MartinLogan, Ltd.

2101 Delaware, Lawrence, KS

MODEL NUMBER : CADENCE

FCC ID: MBBCADENCE

4

WEEE NOTICE

Note: This mark applies only to countries within the European

Union (EU) and Norway.

In accordance with the European Union WEEE (Waste Electrical and Electronic

Equipment) directive 2002/96/EC effective August 13, 2005, we would like to

notify you that this product may contain regulated materials which upon disposal,

according to the WEEE directive, require special reuse and recycling processing.

For this reason Martin Logan has arranged with our distributors in European

Union member nations to collect and recycle this product at no cost to you. To

find your local distributor please contact the dealer from whom you purchased

this product, email [email protected] or visit the distributor locator at

www.martinlogan.com.

Please note, only this product itself falls under the WEEE directive. When dis-

posing of packaging and other related shipping materials we encourage you to

recycle these items through the normal channels.

WARNING/CAUTION!

• Hazardous voltages exist inside—do not remove cover.

• Refer servicing to a qualified technician.

• To prevent fire or shock hazard, do not expose this module to moisture.

• Unplug speaker should any abnormal conditions occur.

• Turn speaker off before making or breaking any signal connections!

• The power cord should not be installed, removed, or left detached from the

speaker while the other end is connected to an AC power source.

• No candles or other sources of open flame should be placed on the speaker.

• No liquids either in glasses or vases should be placed on speaker.

• Speaker should not be exposed to dripping or splashing liquids.

• The terminals marked with the lightning bolt symbol should be connected by

an instructed person or by way of ready made terminals.

• The power cord should remain readily operable should any abnormal condi-

tions occur.

• Any changes or modifications not expressly approved by the grantee of this

device could void the user’s authority to operate the equipment.

IC Information (For Canadian customers)

MODEL NUMBER : CADENCE

IC NO : 11657A-CADENCE

1. PRODUCT CONTAINS TRANSMITTER MODULE IC: 11138A-CAPRICA2L CONTAINS

IC : 11657A-DMRS4

This Class B digital apparatus complies with Canadian CAN ICES-3(B) / NMB-3(B).

Operation is subject to the following two conditions: (1) this product may not cause

harmful interference, and (2) this product must accept any interference received,

including interference that may cause undesired operation.

2. CAUTION

To reduce potential radio interference to other users, the antenna type and its gain

should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not

more than that permitted for successful communication. (i) the device for operation in

the band 5,150-5,250 MHz is only for indoor use to reduce the potential for harm-

ful interference to co-channel mobile satellite systems.(ii) high-power radars are

allocated as primary users (i.e. priority users) of the bands 5,250-5,350 MHz and

5,650-5,850 MHz and that these radars could cause interference and/or damage to

LE-LAN devices.

Radiation Exposure Statement:(ii) high-power radars are allocated as primary users

(i.e. priority users) of the bands 5,250-5,350 MHz and 5,650-5,850 MHz and

that these radars could cause interference and/or damage to LE-LAN devices. This

equipment complies with IC radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with minimum dis-

tance 20 cm between the radiator & your body.

• The maximum antenna gain permitted for devices in the bands 5,250 - 5,350

MHz and 5,470 - 5,725 MHz shall comply with the e.i.r.p. limits specified for

point-to-point and non point-to-point operation as appropriate.

Caution: (i) The device operating in the band 5150–5250 MHz is only for indoor use

to reduce the potential for harmful interference to co-channel mobile satellite systems;

(ii) The maximum antenna gain permitted for devices in the bands 5250–5350 MHz

and 5470–5725 MHz shall comply with the e.i.r.p. limit; and (iii) The maximum

antenna gain permitted for devices in the band 5725–5825 MHz shall comply with

the e.i.r.p. limits specified for point-to-point and non point-to-point operation as

appropriate. (iv) Users should also be advised that high-power radars are allocated

as primary users (i.e. priority users) of the bands 5250–5350 MHz and 5650–5850

MHz and that these radars could cause interference and/or damage to LE-LAN devices.

CE: Hereby, MartinLogan, Ltd., declares that this CADENCE is in compliance with the

essential requirements and other relevant provisions of:

1995/5/EC – R&TTE

2014/30/EU – EMC

2014/35/EU – LVD

2011/65/EU – ROHS2

5

AirPlay, iPad, iPhone, and iPod touch are trademarks of Apple Inc.,

registered in the U.S. and other countries. iPad Air and iPad mini are trade-

marks of Apple Inc.

AirPlay works with iPhone, iPad, and iPod touch with iOS 4.3.3 or later,

Mac with OS X Mountain Lion, and Mac and PC with iTunes 10.2.2 or later.

“Made for iPad” and “Made for iPhone” mean that an electronic accessory

has been designed to connect specifically to iPad, or iPhone, respectively,

and has been certified by the developer to meet Apple performance

standards. Apple is not responsible for the operation of this device or its

compliance with safety and regulatory standards. Please note that the use

of this accessory with iPhone or iPad may affect wireless performance.

Made for:

Apple and the Apple logo are trademarks of Apple Inc., registered in the U.S.

and other countries. App Store is a service mark of Apple Inc.

For DTS patents, see http://patents.dts.com. Manufactured under license from

DTS Licensing Limited. DTS, the Symbol, DTS in combination with the Symbol,

and DTS Digital Surround are registered trademarks or trademarks of DTS, Inc.

Manufactured under license from Dolby Laboratories. Dolby, Dolby Audio

and the double-D symbol are trademarks of Dolby Laboratories.

Qualcomm aptX is a product of Qualcomm Technologies International, Ltd.

Qualcomm is a trademark of Qualcomm Incorporated, registered in the United

States and other countries, used with permission. aptX is a trademark of Qual-

comm Technologies International, Ltd., registered in the United States and

other countries, used with permission

The terms HDMI and HDMI High-Definition Multimedia Interface, and the

HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC

in the United States and other countries.

The Spotify software is subject to third party licenses found here:

www.spotify.com/connect/third-party-licenses

The Bluetooth

®

word mark and logos are registered trademarks owned by Blue-

tooth SIG, Inc. and any use of such marks by MartinLogan, Ltd. is under license.

Windows is a registered trademark of Microsoft Corporation in the United

States and other countries.

Other trademarks and trade names are those of their respective owners.

• iPhone 6s

• iPhone 6 Plus

• iPhone 6

• iPhone 5s

• iPhone 5c

• iPhone 5

• iPad mini 4

• iPad Air 2

• iPad mini 3

• iPad Air

6

Introduction and Overview ...............8

Placement and Mounting ................8

Location ..........................8

Installing on a Flat Surface ..............8

On-Wall Installation ..................9

Connection .........................11

Power Connection ..................11

Signal Connection ..................12

Network Connection ................13

Subwoofer Connection ...............13

IR Outputs ........................14

An Introduction to Audio Connections ......16

Volume Behavior by Input ..............17

Control Panel ........................18

Remote Control ......................18

Changing the Remote’s Battery ..........19

Programming a Second Remote .........19

Display ............................20

The Menu System. . . . . . . . . . . . . . . . . . . . . 21

Entering and Exiting the Menu ..........21

Navigating the Menu ................21

Menu Options .....................21

Installation .....................21

Subwoofer .....................21

An Overview of the Menu Structure .......22

Menu Options (continued)

Bass Level .....................24

Surrounds .....................24

Stereo Mode ...................25

Bass Mode ....................25

Display .......................25

HDMI ........................25

Anthem Room Correction ...........26

Power Settings ..................27

Wireless Setup ..................28

Learn Remote ...................28

Source Name ...................29

Service .......................29

Surround Sound Decoding ..............30

Digital Inputs (HDMI and Optical) ........30

Analog Input ......................30

DTS Play-Fi and Network Connection ......31

Network Requirements ...............31

DTS Play-Fi App Requirements ...........31

Wi-Fi Status LED ....................31

Downloading the DTS Play-Fi App ........31

Connecting to a Wireless Network:

Acces Point Setup ................31

Connecting to a Wireless Network:

Wi-Fi Protected Setup (WPS) .........32

Connecting to a Wired Network ........33

Alternate Setup Without Play-Fi App .......33

Playing Audio Using Play-Fi .............34

Controlling Multiple Speakers ...........34

Additional Play-Fi Features .............35

How to use Connect ...................35

Updates and Rebooting ................35

Rebooting Your Soundbar .............35

Soundbar Firmware Update ............36

DTS Play-Fi Module Update ............36

DTS Play-Fi App Update ..............36

ARC™ (Anthem Room Correction). . . . . . . . . 36

General Information ..................37

Warranty Information ................37

Service .........................37

Serial Number .....................37

Contacting Customer Service ............37

Frequently Asked Questions .............38

Troubleshooting ...................... 39

Specifications .......................42

Dimensional Drawings .................43

Serial Number:_____________________________

Record your serial number here for easy reference.

You will need this information when filling out your

warranty registration. The serial number is located on

the back of the sound bar and on the product carton.

7

wall bracket

wall mount installation template

remote

control

subwoofer

receiver

ARC™

calibrated

microphone

power cord

(North America only)

79 inch

(200 cm)

USB cable

for ARC

79 inch

(200 cm)

IR emitter

96 inch

(244 cm)

subwoofer

receiver power adapter

(North America only)

UK Europe

Australia/China

(only included outside of North America)

shoulder

bolts

AAA batteries

8

IntroductIon and overvIew

Thank you—the MartinLogan owner, for loving

what we do, and making it possible for us to do

what we love.

MartinLogan’s dedicated in-house engineering and

design team developed the Cadence soundbar to

deliver exceptional multi-channel performance from

a single system that easily integrates and installs in

a diverse variety of environments—whether table

or wall mounted. The Cadence produces an envel-

oping field of richly detailed audio for both music

and movies.

Advanced digital signal processing technology

allows MartinLogan to replace five dedicated

home theater speakers with a one piece solution

capable of reproducing multi-channel recordings

with unflinching accuracy, resolution, and detail—

the inspiration behind every MartinLogan design.

The Cadence reproduces front left, right, and

center channels via the system’s dedicated tweet-

ers and woofers. Surround channels are simulated

using sophisticated digital signal processing that

directs sound from the system’s tweeters and woof-

ers throughout the room.

Additionally, for a fully authentic surround sound

experience, the Cadence’s built in subwooferwire-

less transmitter and subwoofer wireless receiver

makes connecting a dedicated subwoofer as sim-

ple as the push of a button.

A suite of integrates wireless streaming technolo-

gies, including DTS Play-Fi™, Apple AirPlay™,

and Bluetooth™, guarantees compatibility with

wireless streaming applications.

Anthem

®

Room Correction (ARC) allows you to

analyze the acoustic response of your listening

environment and adjust output of the soundbar for

optimal performance.

The simple remote control quickly adjusts volume

and selects inputs. The remote also allows you

to easily switch between three discrete acoustic

modes—’Night’ mode (to dial down the bass),

‘Bass+’ mode (for those moments requiring a little

extra thunder), and a ‘Normal’ mode that restores

normal levels.

Placement and mountIng

LOCATION

We recommend locating the soundbar centered

directly above or below your video display. The

soundbar menu allows you to optimize acoustic

performance for either ‘on-wall’ or ‘on-shelf’ instal-

lations. You will learn more about accessing these

options in the “Controls” section of this manual.

INSTALLING ON A FLAT SURFACE

If you have a surface that provides a wide, level,

and stable platform (such as a table or audio/video

rack), the soundbar can be placed directly on top.

When installing the system in this configuration,

use the soundbar’s menu system to choose

‘Installation > Shelf Mount’.

Please note: This speaker is not magnetically

shielded and should not be placed directly beneath

or on top of a CRT television. The magnetic field

will not affect plasma and LCD style televisions.

9

ON-WALL INSTALLATION

The soundbar can be mounted above or below a

television with the feedback display and rear connec-

tion panels orientated towards the bottom or top of

the soundbar (depending on your specific installation

requirements). The information shown on the sound-

bar display can be flipped to match your installation

orientation.

Note: These instructions assume the mounting

surface is standard wood frame and sheetrock

construction. If you wish to mount to another type

of surface, consult a bonded contractor.

Note: When installing the system in this configu-

ration, use the soundbar’s menu system to choose

‘Installation > Wall Mount’.

Required tools (not included):

• Stud finder

• Level

• Electric drill and drill bits

• Phillips screwdriver

Required hardware (included):

• (1) Installation template

• (1) Wall bracket

Required hardware (not included):

• (5) Screws appropriate for mounting surface

• (5) Sheet rock anchors (sized for screws)

1 Locate mounting location using a level and the

installation template (fig. 1).

2 Mark the three central pilot hole locations and

remove the installation template (fig. 1).

Fig. 1

WARNING! We strongly recom-

mend locating the wall bracket so

at least one of the screw locations

attaches to a stud. WARNING!

To prevent injury, this apparatus must be secure-

ly attached to the floor/wall in accordance

with the installation instructions.

10

3 Using a stud finder, determine if there is a wall

stud directly behind one of the three center

screw locations (fig. 2a).

If no stud is found: use the center most screw

location and drill a pilot hole for the wall anchor.

Install a wall anchor at this location. If a wall

stud is found: drill a pilot hole into the stud.

4 Using a screw, attach the wall bracket to the

wall. DO NOT tighten (fig. 2b).

5 Using a stud finder, determine if a wall stud

is directly behind any of the remaining screw

locations (fig. 2a).

If no stud is found: use the top and bottom

center-most screw locations. If a wall stud is

found: use the top and bottom screw locations

with a stud behind them.

Use a level to square the wall bracket and mark

the remaining pilot hole locations (fig. 2b).

6 Remove the wall bracket or pivot to access the

remaining screw locations (fig. 2b).

If no stud is found: drill pilot holes and install

wall anchors. If a wall stud is found: drill pilot

holes into the stud.

7 Using the screws, attach the wall bracket to the

wall. DO NOT fully tighten.

8 Use a level to square the wall bracket. Tighten

all screws (fig. 2b).

9 Attach audio and power cables as needed.

Refer to the ‘Connection’ section of this manual.

10 Move the soundbar into place and drop the

shoulder bolts into the wall bracket keyholes.

Before releasing, make sure the soundbar has

dropped fully into the keyholes and is held firm-

ly in place (fig. 3).

Fig. 2b

or

Fig. 2a

11

Fig. 3

connectIon

WARNING! Turn your soundbar

off before making or breaking any

signal connections! WARNING!

The power cord should not be

installed, removed, or left detached from the

soundbar while the other end is connected to

an AC power source.

POWER CONNECTION

The power cord should be firmly inserted into

the AC power receptacle on the rear connection

panel of the soundbar, then to any convenient AC

wall outlet. The soundbar also integrates a signal

sensing power supply that automatically switches

into standby mode after sensing no audio signal

for approximately 20 minutes (this will only occur

when the menu’s power setting is set to ‘Auto

Standby’).

Fig. 4

7mm

13.7mm

M6

12.7mm

10.3mm

3.2

2mm

12

[Sub Out][Analog 1 In]

[Analog 2 In]

[Left]

White

[Left]

White

[Right]

Red

[Right]

Red

[Optical 1 In]

[Optical 2 In]

[HDMI 1 In] [HDMI 2 In]

[Ethernert][IR Out]

[IR Out]

Factory Use Factory Use

[Wi-Fi

Setup]

[W-Fi

Status LED]

[HDMI 3 In][HDMI Out]

With Audio Return Channel

Factory Use

Fig. 5

If you remove your soundbar from the country of

original sale, be certain that AC power supplied

in any subsequent location is suitable before con-

necting and operating the soundbar. Substantially

impaired performance or severe damage may

occur to the soundbar if operation is attempted

from an incorrect AC power source.

SIGNAL CONNECTION

When utilizing the soundbar to reproduce audio, a

television’s audio output should be defeated. Some

televisions will allow you to turn off the internal

speaker via the television’s menu system. Other

televisions may require you to turn the television’s

volume to “zero” or “mute”.

Additionally, if you’re connecting your television

audio out using a digital optical connection your

television may require you to turn on the digital opti-

cal output and configure the output for 5.1 surround

sound. Please refer to your television’s manual.

Connections are made at the signal input section

on the rear electronics panel of the soundbar. Your

soundbar features the following inputs:

• 3 x HDMI inputs (audio and video)

• 2 x Digital Optical inputs (audio only)

• 2 x Left/Right Analog (RCA) inputs (audio only)

Please note, if your soundbar is being used in an

on-wall installation you may find it helpful to use 90°

RCA adapters, 90° HDMI adapters, and/or low-pro-

file HDMI cables when making signal connections.

When connecting your system, there are any

variety of configurations that will work, and these

methods will vary based on user preference.

Some users will choose to route all sources (such

as DVD player, cable box, game console, media

streamer, etc.) to their television via an HDMI or

digital optical connection and use the television to

switch between audio/video sources. The advan-

tage of this connection method is that only one

audio cable (either HDMI or digital optical cable)

needs to connect between the television and the

soundbar—and changing the input on your televi-

sion will change the audio signal being sent to the

soundbar (without having to change the input setting

on the soundbar itself). Please note: many televisions

are not capable of passing multi-channel encoded

audio signals and will down-mix these signals to

a 2-channel stereo mix before sending them to the

television’s HDMI or digital output.

Most users will want to run cables directly from the

source components to the soundbar and run an

HDMI cable from the soundbar to the TV to pass

13

along the video signal. This allows the soundbar to

receive multi-channel encoded material.

Depending on your number of sources, the TV may

be used for switching some sources while the prima-

ry source devices may be directly connected to the

soundbar for guaranteed multi-channel sound. The

soundbar’s HDMI ARC (Audio Return Channel) allows

video to pass from the soundbar to the television and

audio to pass from the television to the soundbar on

the same HDMI cable. If you’re using your television

as the source, choose the soundbar’s HDMI ARC input

to hear any sounds originating from your television.

Please note, not all telvisions are equipped with HDMI

Audio Return Channel technology.

A few important points to remember when connecting

your soundbar:

• HDMI or digital optical will provide the highest

audio fidelity when connecting to the soundbar.

• If your soundbar is not producing sound or

surround sound from your Blu-ray player, DVD

player, or other multi-channel audio capable

source, you may need to set the player’s digital

audio output to “Bitstream” (also called “Raw”,

“Direct Digital”, or “High Bit Rate”). If “PCM” is

selected you’ll lose the multi-channel encoded

sound. Some players only require you to turn

PCM off to configure for multi-channel encoded

sound. Please refer to your player’s manual.

• In a setup where HDMI is used to connect your

audio/video source component(s) directly to your

television, you will likely need to run an additional

digital optical cable between the source compo-

nent and your soundbar. This extra connection will

allow for multi-channel encoded audio to reach the

soundbar. Many televisions that receive audio/

video source materials via HDMI do not pass

multi-channel encoding when the audio is passed

back out of the televisions digital optical output.

Instead, televisions often pass a 2-channel mix of

the sound, stripping out center, surround and sub-

woofer channels from the mix. This is not true for all

televisions manufactured today, but we have found

the many television on the market work this way.

Using an HDMI connection between the television

and soundbar will maximize the potential of suc-

cessfully passing a multi-channel encoded audio

signal from the television to the soundbar.

• Audio-only sources capable of only stereo output

(such a portable media player docks or CD play-

er) will often connect directly to the soundbar via

the analog input.

NETWORK CONNECTION

To stream audio to your soundbar via DTS Play-Fi or

Apple AirPlay, a LAN (local area network) connec-

tion is required. This connection can be established

using Wi-Fi or Ethernet. Refer to the DTS Play-Fi sec-

tion of this manual for setup and usage details.

SUBWOOFER CONNECTION

You may choose to employ a separate subwoofer

to reproduce the LFE (low frequency effects) chan-

nel information in multi-channel recordings and/

or reinforce bass performance of stereo recordings.

Any aftermarket home theater subwoofer can be

connected via the soundbar’s “LFE Out” RCA con-

nection. We, of course, recommend using a superb

MartinLogan subwoofer.

Additionally, this soundbar integrates a built-in

subwoofer wireless transmitter and includes a sub-

woofer wireless receiver to simplify the connection

and placement of a subwoofer within your room.

No Subwoofer

For systems not using a separate subwoofer,

use the soundbar’s menu system and choose

“Subwoofer > No Sub”. This sets the soundbar to

reproduce the entire frequency range when play-

ing content.

14

Wired Subwoofer Connection

Using a high-quality RCA style cable designed for

subwoofer connection, connect “Sub Out” from the

soundbar to the “LFE In/Sub In” on the subwoofer.

Use the soundbar’s menu system and choose

‘Subwoofer > Wired Sub’.

Reference your subwoofer’s manual to learn how to

properly adjust the sub’s level and phase controls

to achieve proper blending with the soundbar. The

subwoofer’s crossover should be set to “bypass”,

“LFE”. For subwoofers that do not have a “bypass”

or “LFE” crossover setting, we recommend adjusting

the crossover to its highest setting.

Wireless Subwoofer Connection

Use the soundbar’s menu system and choose

‘Subwoofer > Wireless Sub > Sync Subwoofer’.

The soundbar will display ‘Push and Hold Button’.

Press and hold the subwoofer wireless receiver’s

sync button. Connection is successful when the sta-

tus light turns solid and the soundbar responds with

‘Synced’.

Please note: If a link is not established the wireless

receiver’s LED will blink slowly and the soundbar will

display ‘Failed’. Power the soundbar on and off,

unplug the wireless receiver and plug it back in, and

repeat syncing.

Reference your subwoofer’s manual to learn how to

properly adjust the sub’s level and phase controls.

The subwoofer’s crossover should be set to “bypass”

or “LFE”. For subwoofers that do not have a “bypass”

or “LFE” crossover setting, we recommend adjusting

the crossover to its highest setting.

Please note: The subwoofer wireless transmitter

built in to this soundbar is not compatible with

MartinLogan’s SWT-1 or SWT-2 subwoofer wire-

less technology. If your subwoofer has SWT-1 or

SWT-2 technology built in you can still utilize the

soundbar’s wireless functionality by connecting

the wireless subwoofer receiver to the LFE input

on your subwoofer, or connecting an SWT-1 or

SWT-2 transmitter to the Sub Out on the soundbar.

Please note: If you decide to no longer use wire-

less, turn off the soundbar’s wireless transmitter by

using the menu system and choosing ‘Subwoofer

> Wireless Subwoofer > Turn Wireless Sub Off’

or ‘Subwoofer > No Sub’. Doing this will turn off

the transmitter and automatically set the soundbar

for no sub.

WARNING! When operating wirelessly, the

subwoofer may be susceptible to RF interference

in the 2.4GHz bandwidth from microwave ovens

and wireless devices such as Wi-Fi systems, video

game consoles, cordless telephones, Bluetooth

devices, and baby monitors. Generally, this issue

(intermittent sound or slight popping noises) is eas-

ily resolved by physically separating problematic

devices from one another—a distance as little as

two feet will often alleviate the interference. In the

case of microwave ovens, the interference will only

occur when the microwave is operating.

IR OUTPUTS

These jacks accept IR emmiters with 3.5mm mono-

style connectors. One IR emmiter is included with

the soundbar.

Plug the IR emitter into either of the soundbar’s IR

Out jacks and place the other end of the IR emitter

over the IR sensor on another piece of equipment

The use of an IR emitter allows the soundbar to

pass IR signals from any remote control to a teth-

ered device—allowing control of equipment in

locations a remote would normally not reach.

15

Television

*Although HDMI offers the highest quality audio and video

connection (over one cable), another type of video-only cable such

as composite [good], s-video [better], or component [best] might

be required to connect directly to your television—especially

when using sources such as VCRs or older gaming consoles. If you

need to use a non-HDMI video cable, connect an audio-only cable

from the source component directly to the soundbar using either

analog left/right [good] or digital optical [better] audio cables.

[Sub Out][Analog 1 In]

[Analog 2 In]

[Left]

White

[Left]

White

[Right]

Red

[Right]

Red

[Optical 1 In]

[Optical 2 In]

[HDMI 1 In] [HDMI 2 In]

[Ethernet][IR Out]

[IR Out]

Factory Use Factory Use

[Wi-Fi

Setup]

[W-Fi

Status LED]

[HDMI 3 In]

audio & video:

HDMI*

or

audio:

digital optical

Multi-Channel Audio/Video Sources:

Blu-ray, DVD, Game Console,

Cable Box, Satellite Tuner, Etc.

audio:

analog

audio:

digital optical

or

audio:

analog

network:

Ethernet

Non Multi-Channel Audio/Video Sources:

VCR, Older Game Console, Etc.

Network Connection:

Use Ethernet as an alternative

to a Wi-fi connection.

Audio Only Sources:

MP3 Player,

CD Player, Etc.

audio:

analog

subwoofer

Subwoofer:

Use an analog RCA cable as

an alternative to a wireless

subwoofer connection.

audio & video:

HDMI*

[HDMI Out]

With Audio Return Channel

Factory Use

Fig. 6

16

HDMI: HDMI utilizes one cable to pass high-definition video signals and multi-

channel encoded digital audio between a source component and television

or soundbar. Your soundbar is equipped with multiple inputs. These inputs

should be used whenever possible for maximum fidelity.

Digital Optical: Digital optical utilizes one cable to pass digital audio

information (no video). A digital optical cable offers a high-quality digital

connection and passes multi-channel encoded audio between a source

component and an audio output device.

Digital Coaxial: Digital coaxial utilizes one cable to pass digital audio information (no

video). A digital coaxial cable offers a high-quality digital connection and passes

multi-channel encoded audio between a source component and an audio output

device. Please note: The ‘RCA’ style end of a digital coaxial cable is identical

to those found on common left/right analog RCA cables. However, a cable

designed specifically for digital coaxial connections should be employed—do

not use a standard left/right analog RCA style cable because it will likely not be up to the task of han-

dling the high bit-rate necessary for a reliable digital connection.

Left/Right Analog RCA: These cables are used to pass audio information (no video).

An analog RCA cable can only pass a single channel of audio information

between a source component and audio output device. To achieve two-chan-

nels of audio (left/right), you will find that analog RCA cables come bundled

as a stereo pair (two connectors on each end). The Auxiliary input on this

speaker can accept an analog stereo signal through a cable using a 3.5mm

stereo “headphone style” jack. If you are connecting this speaker to a device (such as a dock or CD

player) with left/right RCA analog outputs, you will need a special cable with a 3.5mm ‘headphone

style’ jack on one end and left/right RCA jacks on the other end.

Analog Left/Right RCA to Stereo 3.5mm: Analog cables are used to pass

audio information (no video). Older gaming consoles, portable media player

docks, VCRs and similar source components (which are not capable of play-

ing multi-channel encoded content) will often offer connection only through

left/right analog RCA cables. To connect to these devices use a Left/Right

RCA to stereo 3.5mm cable.

an IntroductIon to audIo connectIons

17

Ethernet: This cable allows you to physically connect a device to a LAN (local area

network). When connected to a LAN, audio information can be sent to this

speaker using various protocols (such as Play-Fi

®

or AirPlay). If a wireless (Wi-

Fi) connection is used to connect to a LAN, there is no need to use an

Ethernet connection. However, in some installations, a ‘hard-wired’ Ethernet

connection may prove more desirable than a wireless connection.

Wi-Fi: This connection technology wirelessly connects a device to a LAN (local area

network). When connected to a LAN, audio information can be sent to this speaker using

various protocols (such as Play-Fi or AirPlay). If an Ethernet connection is used to connect

to a LAN, there is no need to use a Wi-Fi connection. In some installations a ‘hard-wired’ Ethernet

connection may prove more desirable than a wireless connection.

Bluetooth: This wireless connection technology allows a wide variety of devices to connect

to an audio output device and stream audio. Bluetooth establishes a connection directly

with an audio output device and does not require either device to be connected to a LAN.

volume BehavIor By InPut

Depending on the input selected on your speaker, the volume will exhibit different behaviors.

SPEAKER INPUT VOLUME BEHAVIOR

Wireless or Ethernet

(using AirPlay or Play-Fi)

Volume on source device and speaker are synced and control each other.

HDMI, Digital Optical, Analog

Soundbar will control volume level for audio input from most sources.*

Bluetooth

Volume on Bluetooth device and volume on speaker are controlled separately.*

* Devices connected via auxiliary and Bluetooth may have their

own volume control which functions separately from the speak

-

er’s volume. If you are connecting a device which allows you

to adjust its volume separately, we recommend that the volume

on the device not be set to maximum. When set to its maximum

setting, the amplifier in the external device is likely to introduce

elevated levels of distortion into the audio signal which, in turn,

will be further amplified by the speaker. Find a volume between

50–75% of the device’s maximum volume and use your speak

-

er’s volume control to adjust the final playback volume.

an IntroductIon audIo streamIng connectIons

18

control Panel

Your soundbar features seven buttons that control

the following functions:

POWER/STANDBY: Turns the soundbar on/off.

INPUT: Cycles through the inputs. The order of

inputs is: HDM! 1 > HDMI 2 > HDMI 3 > HDMI

ARC > Bluetooth > Optical 1 > Optical 2 >

Analog 1 > Anolog 2.

VOL+/VOL–: Adjusts volume.

When the menu is

activated the volume buttons will function as up/

down

buttons.

MUTE: Mutes the soundbar. When muted, the

soundbar will display ‘Mute’. Pressing this button

a second time or pressing either volume button will

restore the previous volume setting.

ENTER/SELECT: When the menu is activated the

this button allows you to select a menu item.

MENU: Activates the setup menu. When the

menu is activated the menu button will take you

back one level, the volume buttons will function as

up/down, and the Enter/Select button will allow

you to select a menu item. Exit the menu by press-

ing the Menu button.

[Menu]

[Enter/Select]

[Mute]

[Input]

[Power/Standby]

[Volume Down]

[Menu Down]

AND

[Volume Up]

Menu Up]

AND

[

Fig. 8

remote control

Your soundbar remote controls these functions:

POWER: Turns the soundbar on and off.

MENU: Enters and exits the soundbar menu.

MUTE: Mutes the soundbar. When muted, the

soundbar will display ‘MUTE’. Pressing this button

a second time or pressing either volume button will

restore the previous volume setting.

VOL+/VOL–: Adjusts volume level.

BASS MODE – NIGHT: Reduces bass output

and compresses the dynamic range.

BASS MODE – BASS+: Increases bass output.

BASS MODE – NORMAL: Restores normal levels.

INPUT: Activates the selected input.

19

CHANGING THE REMOTE’S BATTERY

The remote control for your speaker uses two AAA

type batteries. Access the battery compartment by

using a Phillips screwdriver to remove the screw lo-

cated on the bottom of the remote.

PROGRAMMING A SECOND REMOTE

This soundbar can be programmed to respond to a

second remote. See “The Menu System” section of

this manual for programming instructions.

Please note:

There may be remote controls that the

soundbar cannot learn or that the soundbar can

not learn correctly. Due to the number of available

remote controls, it is impossible to advise which

will or will not work.

Please note: When learning from a second remote,

you will likely find it does not have buttons that directly

correspond with all available soundbar commands.

Not all soundbar commands have to be programmed.

Some remote controls offer ‘function’ buttons (F1, F2,

etc.) that can be used to program unique soundbar

commands such as ‘NITE.MD’ or ‘OPTIC’.

Please note:

Some remote controls offer discrete

‘power on’ and ‘power off’ buttons. Some offer

only a single button to toggle power on and off.

The learning function of the soundbar allows you to

program for either scenario.

Caution! Danger of explosion if bat-

tery is incorrectly replaced. Replace

only with the same or equivalent type.

Fig. 9

20

dIsPlay

[Anthem Room

Correction Status]

[Current Input

Custom Name]

[Volume Level]

[Wi-Fi Status] [Current Input][Audio Codec Status]

Fig. 10

Your soundbar displays the following information:

Wi-Fi Status: The Wi-Fi icon displays when

a Wi-Fi conneciton is established. If the sound-

bar is configured to connect to a Wi-Fi network

but unable to connect, the icon will change to an

exclamation point.

Please note: The Wi-Fi Status LED on the soundbars

connection panel provides more detailed feedback.

For information on Wi-Fi setup modes and detailed

setup instructions, please refer to the “DTS Play-Fi

and Network Connection” section of this manual.

Audio Codec Status: If an audio signal with

surround sound encoding is detected this icon will

indicate Dolby

®

Digital or DTS Digital Surround™.

Volume Level: Displays the current volume level.

Current Input: This icon indicates the input that

is currently active using its standard input name.

This field is not customizable.

Current Input Custom Name: This indicates

the input that is currently active using its custom

user defined name.

Anthem Room Correction Status: This

icon indicates that Anthem Room Correction is

active. This icon will not display if an Anthem

Room Correction has been manually turned off

or an adjustment curve has not been uploaded

to the soundbar. For information on setting up

ARC, please refer to the “(ARC™) Anthem Room

Correction” section of this manual.

La page est en cours de chargement...

MartinLogan Cadence Manuel utilisateur

MartinLogan Cadence Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents