Smithco Spray Star 1200 Le manuel du propriétaire

Spray Star 1200

Truck Model 20-500-C

Manual System 1201

TeeJet Radion® 8140 1202

TeeJet® 744 1204

TeeJet Aeros/DynaJet® 1215/1218/1220

TeeJet Radion/DynaJet® 1207/1208

SN: 12021

Product Support: Hwy SS & Poplar Ave; Cameron WI 54822

1-800-891-9435 productsupport@smithco.com

Parts & Service

Introduction Service Diagrams Parts Accessories Reference

CONTENTS

Introduction ............................................1-3

Introduction ........................................................................ 1

General Safe Practices...................................................... 2

Specications ................................................................... 3

Optional Spray Equipment................................................. 3

Service ....................................................4-9

Maintenance ................................................................... 4-6

Storage .............................................................................. 6

Service Chart ..................................................................... 7

End User’s Service Chart .................................................. 8

Adjustments ....................................................................... 9

Diagrams ............................................10-13

Wiring Diagram ........................................................... 10-11

Hydraulic Diagram ...................................................... 12-13

Parts....................................................14-59

Body & Frame ............................................................14-15

Engine Cover/ Roll Bat ...............................................16-17

Control Panel and Steering ........................................18-19

Foot Pedal Linkage.....................................................20-21

Front Axle .................................................................22-23

Oil Tank and Fuel Tank ...............................................24-25

Seat Panel .................................................................. 26-27

Hydraulic Pump ..........................................................28-29

Engine and Exhaust ...................................................30-31

Spray Pump ................................................................32-33

Spray Tank ..................................................................34-35

Turbo Quad Agitator ..................................................36-37

Park Brake and Rear Axle ..........................................38-39

15-301 Orbital ............................................................40-41

76-638 Hydrostatic Pump ........................................... 42-43

76-638 Pump Maintenance ........................................44-54

76-197 Eaton Gear Pump................................................ 55

76-197 Pump Maintenace ..........................................56-57

15-970 Hypro® Pump .................................................58-59

Spray Systems ................................. 60-110

Plumbing 1201 Manual System ..................................60-61

Plumbing 1202 System (Radion® 8140) ....................... 62-65

Plumbing 1204 System (TeeJet® 744) ........................66-69

1202 Wiring System(Radion® 8140) .................................. 70

1204 Wiring System (TeeJet® 744) ................................ 71

Control Mounts ...........................................................72-73

Plumbing 1207/1208/1215/1218/1220 .......................74-75

1207/1208 DynaJet Wiring .............................................. 76

1207/1208 Rear Module Mounts ..................................... 77

1215/1218/1220 Aeros Wiring ......................................... 78

1215/1218/1220 DynaJet Wiring ..................................... 79

1215/1218/1220 Rear Module Mounts ............................ 80

14-801/14-607 Strainer.................................................... 81

15-737/14-628 Flanged Strainer...................................... 82

15-743 Manifold Ball Valve .............................................. 83

20-817 Regulaotr Valve ................................................... 84

20-785 Regulator Valve ................................................... 85

17-580 20’ HD Boom .................................................. 86-89

17-580 20’ HD Boom 1202/1204 Plumbing ..................... 90

17-580 20’ HD Boom 1207 Plumbing .............................. 91

17-580 20’ HD Boom 1220 Plumbing .............................. 92

17-585 18’ HD Boom 1218 Plumbing .............................. 93

17-585 18’ HD Boom .................................................. 94-97

17-585 18’ HD 1202/1204 Plumbing ............................... 98

17-585 18’ HD Boom 1208 Plumbing .............................. 99

17-601 15’ HD Boom .............................................. 100-103

17-601 15’ HD Boom 1202/1204 Plumbing ................... 104

17-601 15’ HD Boom 1215 Plumbing ............................ 105

Boom Hinge ................................................................... 106

Standard Nozzle Assembly............................................ 107

1207/1208 Nozzle Assembly ..................................108-109

1215/1218/1220 Nozzle Assembly ................................ 110

Accessories ...................................111-136

15-835 Tank Rinsing System .......................................... 111

16-906 Electric Hose Reel ..................................... 112-113

Electric Hose Reel Wiring Diagram ............................... 114

Hose Reel Adjustments ................................................. 115

16-129 Manual Hose Reel ............................................ 116

15-967 Hose Reel for HD Booms ................................. 117

Hose Reel Plumbing ............................................... 118-119

15-965 Foam Marker Installation ............................120-123

14-291 Foam Marker Parts List .............................. 124-125

Foam Marker Wiring ...................................................... 126

20-815 Water Meter Kit (Gallons) .................................. 127

20-816 Water Meter Kit (Liters) ..................................... 127

15-968 20 Gallon Rinse Tank ................................. 128-129

30-006 Fresh Water Tank - Rear Mount ........................ 130

10-653 Fresh Water Tank - Front Mount........................ 131

15-619 Chemical Clean-load System ..................... 132-136

Reference .......................................137-138

Decal List ....................................................................... 137

Quick Reference Replacement Parts ............................ 138

Limited WarrantyLimited Warranty

1

Introduction

INTRODUCTION

Thank you for purchasing a Smithco product.

Read this manual and all other manuals pertaining to the Spray Star 1200 carefully as they have safety, op-

erating, assembly and maintenance instructions. Failure to do so could result in personal injury or equipment

damage.

Keep manuals in a safe place after operator and maintenance personnel have read them. Right and left sides

are from the operator’s seat, facing forward.

All Smithco machines have a Serial Number and Model Number. Both numbers are needed when ordering

parts. The serial number plate on the Spray Star 1200 is located on right mainframe behind exhaust. Refer to

engine manual for placement of engine serial number.

For product and accessory information, help nding a dealer, or to register your product please contact us at

www.Smithco.com.

Information needed when ordering replacement parts:

1. Model Number of machine

2. Serial Number of machine

3. Name and Part Number of part

4. Quantity of parts

For easy access record your Serial and Model numbers here.

SMITHCO CUSTOMER SERVICE 1-800-891-9435

 

WARNING

Failure to follow cautious operating practices can re-

sult in serious injury to the operator or other persons.

The owner must understand these instructions, and

must allow only trained persons who understand these

instructions to operate this vehicle.

WARNING:

Engine exhaust and some of its constituents are

known to the State of California to cause cancer,

birth defects, and other reproductive harm.

For more information visit

www.P65Warning.ca.gov

2

Introduction

SAFE PRACTICES

1. It is your responsibility to read this manual and all publications associated with this machine.

2. Never allow anyone to operate or service the machine or its optional equipment without proper training

and instructions. Never allow minors to operate any equipment.

3. Learn the proper use of the machine, the location and purpose of all the controls and gauges before

you operate the equipment. Working with unfamiliar equipment can lead to accidents.

4. Wear all the necessary protective clothing and personal safety devises to protect your head, eyes, ears,

hands and feet. Operate the machine only in daylight or in good articial light.

5. Inspect the area where the equipment will be used. Pick up all debris you can nd before operating.

Beware of overhead obstructions and underground obstacles. Stay alert for hidden hazards.

6. Never operate equipment that is not in perfect working order or without decals, guards, shields, or other

protective devices in place.

7. Never disconnect or bypass any switch.

8. Carbon monoxide in the exhaust fumes can be fatal when inhaled, never operate a machine without

proper ventilation.

9. Fuel is highly ammable, handle with care.

10. Keep engine clean. Allow the engine to cool before storing and always remove the ignition key.

11. Disengage all drives and set park brake before starting the engine.

12. Never use your hands to search for oil leaks. Hydraulic uid under pressure can penetrate the skin and

cause serious injury.

13. This machine demands your attention. To prevent loss of control or tipping of the vehicle:

A. Use extra caution in backing up the vehicle. Ensure area is clear.

B. Do not stop or start suddenly on any slope.

C. Reduce speed on slopes and in sharp turns. Use caution when changing directions on slopes.

D. Stay alert for holes in the terrain and other hidden hazards.

14. Before leaving operator’s position:

A. Disengage all drives.

B. Set park brake.

C. Shut engine o and remove the ignition key.

D. If engine has to run to perform any maintenance keep hands, feet, clothing and all other parts of

body away from moving parts.

15. Keep hands, feet and clothing away from moving parts. Wait for all movement to stop before you clean,

adjust or service the machine.

16. Keep the area of operation clear of all bystanders.

17. Never carry passengers.

18. Stop engine before making repairs/adjustments or checking/adding oil to the crankcase.

19. Use parts and materials supplied by Smithco only. Do not modify any function or part.

20. Use caution when booms are down as they extend out beyond the center line of the machine.

21. The tank is a conned space, take precaution.

These machines are intended for professional maintenance on golf courses, sports turf, and any other

area maintained turf and related trails, paths and lots. No guaranty as to the suitability for any task is

expressed or implied.

3

Introduction

SPECIFICATIONS SPRAY STAR 1200

WEIGHTS AND DIMENSIONS

Length 120" (305 cm)

Width 65" (165 cm)

Width With 18' Boom Open 240" (610 cm)

Height w/ Roll Bar 77" (195 cm)

Height w/ 18' Booms Folded 110" (279 cm)

Wheel Base 68" (173 cm)

Weight Empty 1877 lbs (851 kg)

Weight Full 3626 lbs (1645 kg)

SOUND LEVEL (DBA)

At ear level 92 dBA

At 3 ft. (0.914 m) 98 dBA

At 30 ft. (9.14 m) 88 dBA

ENGINE

Make Briggs & Stratton

Model# 613477

Type / Spec# 0271-J1

Horsepower 35 hp (26 kW)

Fuel Unleaded 87 Octane Gasoline Minimum

Cooling System Air Cooled

Lubrication System Full Pressure

Alternator 20 Amp

WHEELS & TIRE Front: Two 20 x 10.00 x 10 NHS Multi-Rib; 20 psi (1.4 bar)

Rear: Two 24 x 13.00 x 12 NHS Multi-Trac; 20 psi (1.4 bar)

SPEED

Innitely Variable 0-12 m.p.h. (0-20 kph)

BATTERY Automotive type 24F - 12 volt

BCI Group Size 24

Cold Cranking Amps 900 minimum

Ground Terminal Polarity Negative (-)

Maximum Length 10.25" (26 cm)

Maximum Width 6.88" (17 cm)

Maximum Height 10" (25 cm)

FLUID CAPACITY

Crankcase Oil See Engine Manual

Fuel 10 gallon (45.46 liters)

Hydraulic Fluid 5 gallon (19 liters)

Grade of Hydraulic Fluid SAE 10W-40 API Service SJ or higher Motor Oil

OPTIONAL EQUIPMENT

20-816 Water Meter Kit (Liters) 20-815 Water Meter Kit (Gallons)

15-619 Chemical Clean-load 10-653 Fresh Water Wash Tank- Front Mount

15-622 Canopy 30-006 Fresh Water Wash Tank - Rear Mount

15-965 Foam Marker 15-968 26 Gal. Wash System with Electric Pump

17-601 15' HD Boom 17-585 18' HD Boom

17-580 20' HD Boom 17-622 Boom Shield for 17-585

15-967 Hose Reel Mount Kit 17-590 Sonic Boom

15-835 Tank Rinsing System

16-129 Manual Rewind Hose Reel, 200-foot/61-meter capacity

16-906 Electric Rewind Hose Reel, 200-foot/61-meter capacity

4

Service

MAINTENANCE

Before servicing or making adjustments to machine, stop engine and remove

key from ignition.

Use all procedures and parts prescribed by the manufacturer's. Read the en-

gine manual before operation.

LUBRICATION

Use No. 2 General purpose lithium base grease and lubricate every 100 hours. The Spray Star 1200 has 7

lube points.

A. One on the rod end of hydraulic cylinder.

B. One on each the right and left spindles.

C. One on the reverse pedal.

D. One on each end of tie rod.

E. One on the forward pedal.

ELECTRICAL CONNECTIONS

Use dielectric grease on all electrical connections.

AIR CLEANER ON ENGINE

1. Unclip the two clips, remove the cover and pull out the element.

2. To service, clean by tapping gently on at surface. Do not oil. Replace if very dirty or damaged.

3. Clean out the inside of the body and cover.

4. Place the element into the body and put the cover back on..

Do not use petroleum solvents, e.g.., kerosene, which will cause cartridge to

deteriorate. Do not use pressurized air to clean cartridge. Pressurized air can

damage cartridge.

5

Service

MAINTENANCE

ENGINE OIL

Change and add oil according to chart below based on air temperature at the time of operation. Do not over-

ll. Use a high-quality detergent oil classied for service SF, SG, SH. SJ or higher. Use no special additives

with recommended oils. Do not mix oil with gasoline.

SAE Viscosity Grades

HYDRAULIC OIL

1. Use SAE 10W-30 API Service SJ or higher motor oil.

2. For proper warranty, change oil every 500 hours or annually, which ever is rst.

3. Oil level should be 2-2½" (5-6.4cm) from top of the tank when uid is cold. Do not overll.

4. After changing oil, run the machine for a few minutes. Check oil level and for leaks.

5.

Always use extreme caution when lling hydraulic oil tank or checking level to keep system free of con-

taminants. Check and service more frequently when operating in extremely cold, hot or dusty conditions.

6. If the natural color of the uid has become black or smells burnt, it is possible that an overheating prob-

lem exists.

7. If uid becomes milky, water contamination may be a problem.

8. If either of the above conditions happen, change oil immediately after uid is cool and nd the cause.

Take uid level readings when the system is cold.

9. In extreme temperatures you can use straight weight oil. We recommend SAE 30W API Service SG

when hot (above 90°F (33°C)) and SAE 10W API Service SJ or higher when cold (below 32°F (0°C)

ambient temperature. Use either motor oil or hydraulic oil, but do not mix.

10. Oil being added to the system must be the same as what is already in the tank. Mark the tank ll area

as to which type you put in.

TIRE PRESSURE

Caution must be used when inating a low tire to recommended pressure. Over inating can cause tires to

explode. All tires should be 20 psi (1.4bar). Improper ination will reduce tire life considerably.

WHEEL MOUNTING PROCEDURE

1. Set park brake. Turn machine o and remove key.

2. Block wheel on opposite corner.

3. Loosen nuts slightly on wheel to be removed.

4. Jack up machine being careful not to damage underside of machine.

5. Place wheel on hub lining up bolt holes.

6. Torque to 64-74 ft/lb (87-100Nm) using a cross pattern. Re-torque after rst 10 hours and every 200

hours thereafter.

7. Lower machine to ground and remove blocks and jack.

6

Service

MAINTENANCE

BATTERY

Batteries normally produce explosive gases which can cause personal injury. Do not allow ames, sparks or

any ignited object to come near the battery. When charging or working near battery, always shield your eyes

and always provide proper ventilation.

Battery cable should be disconnected before using “Fast Charge.”

Charge battery at 15 amps for 10 minutes or 7 amps for 30 minutes. Do not exceed the recommended

charging rate. If electrolyte starts boiling over, decrease charging.

Always remove grounded (-) battery clamp rst and replace it last. Avoid hazards by:

1. Filling batteries in well-ventilated areas.

2. Wear eye protection and rubber gloves.

3. Avoid breathing fumes when electrolyte is added.

4. Avoid spilling or dripping electrolyte.

Battery Electrolyte is an acidic solution and should be handled with care. If

electrolyte is splashed on any part of your body, ush all contact areas imme-

diately with liberal amounts of water. Get medical attention immediately.

Use of booster battery and jumper cables. Particular care should be used

when connecting a booster battery. Use proper polarity in order to prevent

sparks.

TO JUMP START (NEGATIVE GROUNDED BATTERY):

1. Shield eyes.

2. Connect ends of one cable to positive (+) termi-

nals of each battery, rst (A) then (B).

3. Connect one end of other cable to negative (-)

terminal of "good" battery (C).

4. Connect other end of cable (D) to engine block

on unit being started (NOT to negative (-) termi-

nal of battery)

To prevent damage to other electrical components on

unit being started, make certain that engine is at idle

speed before disconnecting jumper cables.

STORAGE

If the engine will be out of service for two or more months, use the following storage procedure.

1. Clean the exterior surfaces of the engine.

2. Change the oil and lter while the engine is still warm from operation.

3. The fuel system must be completely emptied, or the gasoline must be treated with a stabilizer to prevent deteriora-

tion.

If you choose to use a stabilizer, follow manufacturers recommendations, and add the correct amount for the ca-

pacity of fuel system. Fill fuel tank with clean, fresh gasoline. Run engine for 2-3 minutes to get stabilized fuel into

carburetor. Close fuel shut-o valve when unit is being stored or transported.

To empty the system, drain fuel tank and carburetor, or run engine until tank and system are empty.

4. Remove the spark plugs. Add one tablespoon of engine oil into each spark plug hole. Install plugs, but do not con-

nect the plug leads. Crank the engine two or three revolutions.

5. Store machine in a clean, dry place.

7

Service

SERVICE CHART

Before servicing or making adjustments to the machine, stop engine, set park

break, block wheels and remove key from ignition.

Follow all procedures and ONLY use parts prescribed by the manufacturer.

Read the engine manual before maintenance.

The suggested maintenance checklist is not oered as a replacement for the manufacturer’s engine manual

but as a supplement. You must adhere to the guidelines established by the manufacturer for warranty cover-

age. In adverse conditions such as dirt, mud or extreme temperatures, maintenance should be more frequent.

Maintenance Service Interval Maintenance Procedure

After the rst 8 operating hours Torque the wheel lug nuts. (64-74 ft/lb (87-100 Nm))

Change the engine oil lter.

Before each use daily

Check the engine oil level.

Clean area around muer and controls.

Check the hydraulic uid level.

Check the tire pressure.

Check condition of hydraulic hoses and ttings.

Inspect and clean the machine.

After the rst 50 hours Change Hydraulic Oil Filter.

Every 100 hours

Clean or change air lter.1&2

Clean pre-cleaner.1

Change engine oil and lter.

Replace spark plug .

Lubricate machine.

Clean or change remote air cleaner.

Check the battery uid level and cable connections..

Service exhaust sytem.

Check belt tension .

Every 250 hours

Check engine valve clearance and adjust if necessary.

Check idle speed.

Clean battery terminals.

Change hydrauilic oil lter.

Torque the wheel lug nuts. (64-74 ft/lb (87-100 Nm))

Every 500 hours or yearly

Change fuel lter.

Change hydrauilic oil and lter.

Clean oil cooler ns.1

Replace air lter2

Replace fuel lter

Clean air cooling system.1

Check safety lter in remote air cleaner.

1 In dusty conditions or when airborne debris is present, clean more often.

2 Every third air lter change, replace the inner safety lter.

8

Service

END USER SERVICE CHART

Duplicate this page for routine use.

Maintenance Check Item For the week of:

Mon Tues. Wed. Thurs. Fri. Sat. Sun.

Check the Safety Seat Switch

Check Steering Operation

Check the fuel level

Check the engine oil level.

Clean the air lter

Clean the engine cooling ns.

Check for unusual engine noises

Check the hydraulic oil level

Check hydraulic hoses and ttings for damage

Check for uid leaks.

Check the tire pressure

Check the Instrumentation

Inspect electrical system for frayed wires

Check park brake adjustment

Change oil lter.

Change oil.

Lubricate Machine

Ensure all warning decals are intact.

Areas of Concern

Inspection Performed by:

Item Date Information

9

Service

ADJUSTMENTS

WHEEL CREEP

"Creep" is when the engine is running and hydrostatic transmission is in neutral, but due to inadequate align-

ment, wheels still move. Do the following procedure to stop this motion.

1. Lift up and support machine so rear wheels are o the ground and can turn freely.

2. In the engine compartment, the hydrostatic transmission

is on the left side. The shift arm (D) is under the pump and

comes out the side. The idler arm (B) has a bearing that

runs in the notch of the shift arm. Loosen bolt (A).

3. With engine running, move bearing (B) so it centers on the

shift arm (D) and 'wheel creep' stops.

4. Tighten all fasteners and test by using foot pedal linkage to

see that 'creep' is removed.

5. Turn engine o and lower machine.

SPRAY PUMP WITH BELT

Located below the engine. The belt should have approximately

1/2" (13mm) of deection in the center of the top strand. Loosen and tighten the 5/16 -18 x 11/4 set screw located

on the foot of the pump mount.

PARK BRAKE

Turn knob clockwise on end of park brake to tighten. Turn it counter clockwise to loosen. If ner adjustment is

needed turn clevis on brake cable to adjust length of cable.

MASTER BOOM SWITCH (FOOT SWITCH)

The master boom switch, located on the left oorboard is used to override the master switch on the computer

console of the spray systems. By pushing down it will turn on/o the booms.

GROUND SPEED CONTROL (FOOT SWITCH))

The ground speed control does not work the same as an automotive type cruise. The ground speed control is

located on the left oorboard and is used to lock forward speed.

TO ENGAGE:

1. Flip rocker switch ‘On’ (green light).

2. Obtain desired speed with foot pedal.

3. Step on foot switch to lock speed.

4. Push foot switch again to disengage.

SPRAY BOSS CONTROL - ORANGE

Engages and disengages speed boss. Forward is engage and all the way back is disengage. When the lever

is engaged it sets a stop for the accelerator. The accelerator pedal must be used to maintain this speed. To

adjust speed use the knob on the end of the lever, counter clockwise increases speed and clockwise decreas-

es speed. Disengage the lever and you will have full accelerator pedal range.

10

Diagrams

Color Code Chart

Bl Blue

Br Brown

Y Yellow

G Green

O Orange

R Red

B Black

GY Gray

W White

WIRING DIAGRAM

11

Diagrams

WIRING PARTS LIST

REF# PART# DESCRIPTION QUANTITY

1 30-356 GPS Speedometer 1

2 12-804 Hour Meter 1

3 10-732 LED Light 1

4 Lights

15-782 Non-Lighted Switch, On-None-O 1

15-727 Rocker - No light 1

5 Cruise

15-726 Lighted Switch 1

15-732 Rocker - Green 1

6 Pump

15-726 Lighted Switch 1

15-731 Rocker - Amber 1

7 Left Boom

15-727 Rocker - No light 1

15-728 Centering Switch, Momentary, On-O-On 1

8 Right Boom

15-728 Centering Switch, Momentary, On-O-On 1

15-727 Rocker - No light 1

9 30-214 Boom Actuator 2

10 15-970 Spray Pump 1

11 33-480 Pressure Switch 1

12 77-207 Buzzer 1

8874 Female Bullet 1

8875 Male Bullet 2

8963 Heat Shrink 2

13 33-084 Magnetic Coil 1

14 76-636 Briggs & Stratton 35 HP Engine 1

15 76-327 Negative Battery Cable 1

16 Solenoid 1

17 75-518 Red Battery Cable 1

18 33-216 Battery 1

19 77-261 40 Amp Circuit Breaker 1

8977 Red Circuit Breaker Boot 1

20-733 10AMP Circuit Breaker 1

8877 Red Circuit Breaker Boot 1

20 14-292 Seat Switch 1

21 13-488 Key Switch 1

22 20-730-01 GPS Antenna (part of speedometer) 1

23 32-576 USB 1

24 50-359 Oil Temperature Light 1

25 30-042-06 Relay 2

26 33-509 Master Boom Switch 1

27 76-471 Electric Fuel Pump 1

28 8931-20 10GA White Wire 1

8928 5/16 Ring Terminal 1

8912 3/16 Ring Terminal 1

8963 Heat Shrink 2

29 8919-26 10GA Red Wire 1

8928 5/16 Ring Terminal 1

8912 3/16 Ring Terminal 1

8963 Heat Shrink 2

30 33-271 Fuse Panel 1

15-941 Wire Harness 1

Use dielectric grease on all electrical connections.

12

Diagrams

HYDRAULIC DIAGRAM

13

Diagrams

HYDRAULIC DIAGRAM PARTS LIST

REF# PART# DESCRIPTION QUANTITY

1 15-624 Cooler 1

2 15-947 Hydraulic Hose, 34" 1

3 15-946 Hydraulic Hose, 74" 1

4 15-301 Orbital 1

5 10-671 Hydraulic Hose, 65" 2

6 15-839 Hydraulic Cylinder 1

15-839-01 Seal Kit 1

7 15-945 Hydraulic Hose, 76.5" 1

8 76-638 Hydrostatic Pump 1

9 76-197 Gear Pump 1

10 15-682 Hydraulic Hose, 463/4" 2

11 20-656 Tube Assembly 4

12 76-238 Wheel Motor 2

13 34-057 Tee 2

14 8832-30 3/4" Suction Hose x 30" 1

18-040 Hose Clamp 2

15 8832-29 3/4" Suction Hose x 29" 1

18-040 Hose Clamp 2

16 60-473 Hydraulic Oil tank 1

17 8917-16 3/8" Suction Hose x 16" 1

18-040 Hose Clamp 2

18 26-016 Oil Filter 1

23-031 Replacement Filter 1

19 15-948 Hydraulic Hose, 16.5" 1

PUMP DISPLACEMENT

76-638 Hydrostatic Pump

Displacement Variable to 1.44 in3/R (23.6 cm3/R)

22.44 gpm (84.94 lpm) at 3600 rpm

Max Operating Speed 3600 rpm

Rated Pressure 3000 psi (206.8 bar)

Max Pressure 5000 psi (344.7 bar)

Max Inlet Vacuum 6 in Hg (.203 bar)

Max Inlet Temperature 225°F (107°C)

Max Allowable Case Pressure 25 psi (1.72 bar)

76-197 Gear Pump

Displacement .40 in3/R (6.6 cm3/R) 6.23 gpm (25.39 lpm)

Over tightened ttings will result in crushing the cone which will create a

leak.

14

Parts

MAIN DRAWING

Parts

15

BODY & FRAME PARTS LIST

REF# PART# DESCRIPTION QUANTITY

1 10-678 Reverse Pedal 1

2 10-677 Forward Pedal 1

3 15-925 Main Frame 1

4 10-663 RH Front Fender 1

5 16-857 Front Tire and Wheel 2

16-857-01 Tire, 20 x 10.00 - 10NHS 4 Ply 2

42-161-02 Wheel 2

6 10-683 Side Control Arm 1

10-684 Control Panel 1

7 20-659 Mud Flap 4

8 60-106 Park Brake Handle 1

9 15-781 Drink Cup Holder 1

10 76-198-03 Seat Belt 1

11 15-963 Tailpipe 1

12 15-962 Tailpipe Guard 1

13 20-812 Front Tank Strap 1

14 16-225 Rear TIre and Wheel 2

16-225-01 Tire, 24 x 13.00 - 12NHS 4 Ply 2

16-225-02 Wheel 2

15 10-168 Rear Fender 2

16 20-811 Rear Tank Strap 1

17 17-615 Boom Support Tube 2

18 16-557 Square Cap 2

19 20-802 200 Gallon Spray Tank 1

16-169 Strainer Basket 1

20 15-964 Air Gap Filler 1

21 16-953 Lid 1

16-953-01 Gasket for Lid 1

22 10-639 Lid Stop 1

23 15-922 Roll Bar 1

24 15-936 Engine Hood 1

25 15-934 Back Panel 1

26 14-294 Seat kit 1

10-706 Arm Rests 1

27 10-120 Speed Boss Handle 1

28 20-057 Steering Wheel 1

20-129 Center Steering Wheel Cap 1

29 10-732 LED Head Light 1

30 10-662 LH Front Fender 1

31 10-680 Seat Frame 1

32 10-705 Foot Rest 1

16

Parts

ENGINE HOOD & ROLL BAR DRAWING

Parts

17

ENGINE HOOD AND ROLL BAR PARTS LIST

REF# PART# DESCRIPTION QUANTITY

1 15-940 RH Fender Brace 1

15-939 LH Fender Brace (not shown) 1

2 20-659 Mud Flap 2

3 HBC-516-18-100 Carriage Bolt, 5/16 -18 x 1 4

HNFL-516-18 Flange-Loc Nut, 5/16 - 18 4

4 HB-14-20-075 Hex Bolt, 1/4 -20 x 3/4 6

HNFL-14-20 Flange-Loc Nut, 1/4- 20 6

5 HWF-14-150 Fender Washer, 1/4 x 11/2 6

6 HB-12-13-175 Hex Bolt, 1/2 - 13 x 13/4 10

HW-12 Flat Washer, 1/2 10

HNTL-12-13 Lock Nut, 1/2 - 13 10

7 15-935 Seat Belt Bracket 2

HB-12-13-150 Hex Bolt, 1/2 - 13 x 11/2 4

HNTL-12-13 Lock Nut, 1/2 - 13 4

8 15-922 Roll Bar 1

9 15-013 Rubber Bumper 2

HNFL-14-20 Flange-Loc Nut, 1/4 - 20 2

10 15-952 RH Hood Stand 1

11 15-936 Engine Hood 1

12 HSTP-516-18-075 Truss Head Screw, 5/16 -18 x 3/4 4

HNFL-516-18 Flange-Loc Nut, 5/16 - 18 4

13 15-951 LH Hood Stand 1

14 32-695 Adjustable Hinge 2

15 HSM-10-32-063 Machine Screw, 10-32 x 5/8 8

HNFL-10-32 Flange-Loc Nut, 10 - 32 8

16 15-934 Back Panel 1

9023 Heat Reective Matting (18 x 25.5) 1/4 Sheet

17 HB-38-16-075 Hex Bolt, 3/8 -16 x 3/4 2

HNFL-38-16 Flange-Loc Nut, 3/8 -16 2

18 hb-38-16-125 Hex Bolt, 3/8 - 16 x 11/4 1

HNTL-38-16 Lock Nut, 3/8 - 16 1

19 HB-38-16-150 Hex Bolt, 3/8 - 16 x 11/2 1

HNTL-38-16 Lock Nut, 3/8 - 16 1

20 15-931 Fuel Pump mount 1

76-471 Fuel Pump 1

18

Parts

CONTROL PANEL AND STEERING DRAWING

La page charge ...

Smithco Spray Star 1200 Le manuel du propriétaire

Smithco Spray Star 1200 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents