Wacker Neuson TH522 (TL48-01) Manuel utilisateur

Taper
Manuel utilisateur

Ce manuel convient également à

Operator’s manual
Telehandlers
TH522
Machine model TL48
Document number 1000382391
Date
08/2018
Version
2.2
Language
[kn]
This Operator's Manual includes
the AEM 3afety -anual RTF-0907
Copyright – Wacker Neuson SE
Printed in Germany
All rights reserved, in particular the copyright, the right of reproduction and the right of distribution applicable
worldwide.
This document may be used by the receiver only for the designated purpose. It may in no way be duplicated or
translated into any other language, in whole or in part, without prior permission in writing from the manufacturer.
No reproduction or translation of this publication, in whole or in part, without the written consent of Wacker
Neuson SE.
Violations of legal regulations, in particular of the copyright protection, shall be subject to civil and criminal
prosecution.
Wacker Neuson SE keep abreast of the latest technical developments and constantly improve their products. For
this reason, we may from time to time need to make changes to figures and descriptions in this documentation
that do not reflect products that have already been delivered and that will not be implemented on these vehicles.
Technical data, dimensions and weights are only given as an indication. Responsibility for errors or omissions not
accepted.
The cover features the machine with possible optional equipment.
Legend
Original Operator’s Manual
Version
2.2
Date
08/2018
Document BA TH522 *
Documentation
Language Order no. Operator’s manual
[us] en 1000382391
[kn] fr 1000382363
[mx]
es
1000382367
[br] pt 1000382392
BA TH522 * 01/2018 * BA_TH522_0_IVZ_us.fm * [us]
I-1
Table of contents I
Table of Contents
1Preface
1.1 Operator’s manual................................................................................................................................. 1-1
1.2 Warranty and liability............................................................................................................................. 1-5
2 Safety
2.1 Safety symbols and signal words.......................................................................................................... 2-1
2.2 Qualification of operating personnel...................................................................................................... 2-2
2.3 Conduct................................................................................................................................................. 2-3
2.4 Operating............................................................................................................................................... 2-4
2.5 Lifting gear applications......................................................................................................................... 2-8
2.6 Trailer operation.................................................................................................................................. 2-10
2.7 Attachment operation.......................................................................................................................... 2-11
2.8 Towing, loading and transporting ........................................................................................................ 2-12
2.9 Maintenance........................................................................................................................................ 2-15
2.10Measures for avoiding risks................................................................................................................. 2-18
3 Introduction
3.1 Machine overview.................................................................................................................................. 3-1
3.2 Brief description of the machine............................................................................................................ 3-2
3.3 Information and regulations on use....................................................................................................... 3-5
3.4 Labels.................................................................................................................................................... 3-8
4 Putting into operation
4.1 Cabin/control stand ............................................................................................................................... 4-1
4.2 Overview of control elements.............................................................................................................. 4-11
4.3 Indicator lights and warning lights (overview)...................................................................................... 4-21
4.4 Preparations........................................................................................................................................ 4-32
4.5 Starting and stopping the engine......................................................................................................... 4-38
5 Operation
5.1 Steering system..................................................................................................................................... 5-1
5.2 Accelerator actuation............................................................................................................................. 5-4
5.3 Brake..................................................................................................................................................... 5-6
5.4 Machine travel operation....................................................................................................................... 5-8
5.5 Differential lock (option)....................................................................................................................... 5-16
5.6 Lights/signaling system ....................................................................................................................... 5-17
5.7 Wiper/washer system.......................................................................................................................... 5-21
5.8 Heating, ventilation and air conditioning system (option).................................................................... 5-22
5.9 Working hydraulics.............................................................................................................................. 5-24
5.10Attachments ........................................................................................................................................ 5-50
5.11Work operation.................................................................................................................................... 5-57
5.12Emergency lowering............................................................................................................................ 5-68
5.13Options................................................................................................................................................ 5-70
5.14Putting out of operation/back into operation........................................................................................ 5-91
5.15Permanently putting out of operation .................................................................................................. 5-93
6 Transportation
6.1 Towing the machine.............................................................................................................................. 6-1
6.2 Loading the vehicle ............................................................................................................................... 6-4
6.3 Transporting the vehicle........................................................................................................................ 6-8
Table of contents
I-2
BA TH522 * 01/2018 * BA_TH522_0_IVZ_us.fm * [us]
I Table of contents
7 Maintenance
7.1 Information on maintenance.................................................................................................................. 7-1
7.2 Maintenance overview........................................................................................................................... 7-5
7.3 Fluids and lubricants ........................................................................................................................... 7-14
7.4 Maintenance accesses........................................................................................................................ 7-15
7.5 Cleaning and maintenance.................................................................................................................. 7-16
7.6 Lubrication work .................................................................................................................................. 7-18
7.7 Fuel system......................................................................................................................................... 7-19
7.8 Engine lubrication system ................................................................................................................... 7-24
7.9 Cooling system.................................................................................................................................... 7-26
7.10Air filter ................................................................................................................................................ 7-31
7.11V-belt/toothed belt ............................................................................................................................... 7-34
7.12Hydraulic system................................................................................................................................. 7-36
7.13Electrical system ................................................................................................................................. 7-41
7.14Heating, ventilation and air conditioning system (option).................................................................... 7-46
7.15Washer system.................................................................................................................................... 7-48
7.16Axles/travel drive................................................................................................................................. 7-49
7.17Braking system.................................................................................................................................... 7-50
7.18Tires .................................................................................................................................................... 7-51
7.19Maintenance and servicing work on attachments ............................................................................... 7-54
7.20Maintenance of options ....................................................................................................................... 7-55
8 Malfunctions
8.1 Malfunctions, causes, remedies............................................................................................................ 8-1
9 Technical data
9.1 Models and trade names....................................................................................................................... 9-1
9.2 Engine ................................................................................................................................................... 9-1
9.3 Traveling drive/axles ............................................................................................................................. 9-2
9.4 Brakes ................................................................................................................................................... 9-2
9.5 Tires ...................................................................................................................................................... 9-3
9.6 Steering system..................................................................................................................................... 9-3
9.7 Working hydraulics................................................................................................................................ 9-3
9.8 Electrical system ................................................................................................................................... 9-4
9.9 Tightening torques................................................................................................................................. 9-9
9.10Coolant................................................................................................................................................ 9-10
9.11Noise emissions .................................................................................................................................. 9-10
9.12Vibration.............................................................................................................................................. 9-11
9.13Weights ............................................................................................................................................... 9-12
9.14Payload/load-carrying capacity/lift capacity......................................................................................... 9-12
9.15Dimensions.......................................................................................................................................... 9-14
Index
BA TH522 * 01/2018 * BA_TH522_1_Vorwort_us.fm * [us]
1-1
Preface 1
1 Preface
1.1 Operator’s manual
Information on this Operators Manual
This Operator’s Manual describes how to operate and perform
maintenance on the machine. It provides operating and maintenance
personnel with the necessary knowledge of the machine’s functional
characteristics to ensure safe handling, correct maintenance, inspection
and cleaning, and to ensure that the technical safety regulations for the
machine are complied with.
Your own safety, as well as the safety of others, depends to a great extent
on how the machine is moved and operated. Therefore, carefully read and
understand this Operator’s Manual prior to the first drive. By reading the
Operator’s Manual, the operator familiarizes himself more quickly with the
machine, and uses it more safely and efficiently.
If required, the user/owner of the machine must supplement the
Operator’s Manual with instructions and regulations regarding
environmental protection and national accident prevention regulations.
Operational safety and readiness of the machine do not only depend on
the operator’s skill, but also on maintenance and servicing of the machine.
This is why regular maintenance and servicing is absolutely necessary.
Please refer to “Information on cleaning and maintenance” on page 7-16
for an overview of the maintenance and service work. An inspection
booklet is also supplied with the machine.
Information
The maintenance and repair work that is not specified in this Operator’s
Manual may only be performed by an authorized service center.
The Operator’s Manual must be read and applied by all persons involved
in work with or on the machine, for example, with regard to:
Operation, including setting up, rectifying malfunctions during
operation, maintenance, disposal of auxiliary and operating material,
and disposal of the entire machine.
Repairs (inspection, maintenance).
Transportation.
Your dealer and the Wacker Neuson service team will be happy to answer
any questions you may have on this Operator’s Manual.
All technical indications in this Operator’s Manual refer to series models
tested under standard operating conditions for Central Europe and
describe the standard functions of these series models. The equipment
and its functional modes and accessories depend on the relevant model
and the product options, as well as on the national requirements.
Illustrations may show optional/additional equipment that is not mentioned
in the text or not supplied as standard.
Preface
Table of contents
Index
1-2
BA TH522 * 01/2018 * BA_TH522_1_Vorwort_us.fm * [us]
1 Preface
The descriptions, illustrations, weight indications and technical data are
not binding and correspond to the state of the art at the time of printing.
We must reserve the right to make changes without prior notice with
regard to design, equipment, appearance and technology on account of
the ongoing further development of the products.
At the place of use, always observe all safety and warning instructions,
information labels, legal regulations and regulations of the German social
insurance against occupational accidents.
Please get in touch with the Wacker Neuson service department if you
require any special functions that are only available using additional
components and/or under special conditions.
We will be happy to answer questions and provide information on the
conditions under which the product and the circumstances allow any
special functions.
We recommend performing test work in safe conditions if the load
capacity or mode of action of our products give rise to concern under
specific circumstances.
Information
The word “loader unit” is used in this Operator’s Manual for the loader unit
with an attachment installed on it.
“Left” and “right” are always used as seen in the forward travel direction.
BA TH522 * 01/2018 * BA_TH522_1_Vorwort_us.fm * [us]
1-3
Preface 1
Explanation of symbols
This symbol identifies warning instructions and is used for alerting against
potential personal hazards. Special attention must be paid to the warning
instruction texts following this symbol.
Abbreviations
Symbol Explanation
Identification of general activities
- Identification of subdivision and order of activity
Identification of the results of an enumeration
Identification of the results of an activity
Identification of descriptions referring to figures (pos.)
Identification of control and display elements (pos.). The
numbering applies to the entire Operator’s Manual
1
1
Abbreviation Explanation
poss. possibly
if nec. if necessary
etc. et cetera
e.g. for example
max. maximum
min. minimum
approx. approximately
Fig. Figure
Item Position number in figures
(option) Optional/additional equipment on machine
and much
more
And much more
incl. including, inclusive
1-4
BA TH522 * 01/2018 * BA_TH522_1_Vorwort_us.fm * [us]
1 Preface
Conversion tables
Values in brackets are values converted according to the tables below.
The units of measurement are American units. The values are rounded up
or down on the basis of good commercial practice.
Volume unit
1 cm³ 0.061 in³
1 m³ 35.31 ft³
1 ml 0.034 US fl.oz.
1 l 0.26 gal
1 l/min 0.26 gal/min
Unit of length
1 mm 0.039 in
1 m 3.28 ft
Weight
1 kg 2.2 lbs.
1 g 0.035 oz.
Pressure
1 bar 14.5 psi
1 kg/cm³ 14.22 lbs/in³
Force/output
1 kN 224.81 lbf.
1 kW 1.34 hp
1 PS 0.986 hp
Torque
1 Nm 0.74 ft.lbs.
Speed
1 kph 0.62 mph
Acceleration
1 m/s² 3.28 ft/s²
BA TH522 * 01/2018 * BA_TH522_1_Vorwort_us.fm * [us]
1-5
Preface 1
1.2 Warranty and liability
Information on warranty and liability
The CE mark shows that the machine has been manufactured in
accordance with the applicable EC Directives.
Information
The manufacturer/supplier shall be not liable for damage resulting from
use other than designated. Alone the user/owner shall bear the risk. The
Operator’s Manual must always be on the machine or at the place of use.
Keep this Operator's Manual at the place provided for it, on the right of the
operator's seat in the cab(Fig. 1).
Exemption from warranty and liability
Despite taking great care, we cannot rule out the possibility of deviations
from drawings or dimensions, calculation errors, printing errors or
incompleteness in this Operator’s Manual. Therefore, we shall accept no
liability for the correctness and completeness of the information we have
provided in this Operator’s Manual. The options described in this
Operator’s Manual are not available in all countries. We warrant our
products to be in perfect running condition within the framework of our
General Terms and Conditions of Business. We basically do not offer any
further guarantees. Any further liability beyond the scope of our General
Terms and Conditions of Business is excluded.
Observe the following:
Do not perform any modifications on the machine.
Use only attachments approved by the manufacturer for the machine.
The machine must only be put into operation, operated and serviced
as described in the Operator’s Manual.
Use only the machine if all safety and protection devices are intact.
Observe the monitoring systems during operation
Repairs may only be performed by authorized service centers.
Follow the instructions given in the Operator’s Manual carefully.
Fig. 1
1-6
BA TH522 * 01/2018 * BA_TH522_1_Vorwort_us.fm * [us]
1 Preface
Notes:
BA TH522 * 01/2018 * BA_TH522_2_Sicherheit_us.fm * [us]
2-1
Safety 2
2Safety
2.1 Safety symbols and signal words
Explanation
The following symbol identifies safety instructions. It is used for warning
against potential personal risk or danger.
DANGER
DANGER identifies a situation causing death or serious injury if it is
not avoided.
Consequences in case of non-observance.
Avoidance of injury or death.
WARNING
WARNING identifies a situation that can cause death or serious
injury if it is not avoided.
Consequences in case of non-observance.
Avoidance of injury or death.
CAUTION
CAUTION identifies a situation that can cause injury if it is not
avoided.
Consequences in case of non-observance.
Avoidance of injury.
NOTE
NOTICE identifies a situation that causes damage to the machine if it is
not observed.
Avoidance of damage to property.
Safety
2-2
BA TH522 * 01/2018 * BA_TH522_2_Sicherheit_us.fm * [us]
2 Safety
2.2 Qualification of operating personnel
Owners duties
Only allow specifically authorized, trained and experienced persons to
operate, drive and perform maintenance on the vehicle.
Do not allow persons to be trained or instructed by anyone other than
an authorized and experienced person.
Have persons to be trained or instructed practice under supervision
until they are familiar with the machine and its behavior (for example,
with the steering and braking behavior).
Access to the vehicle or vehicle operation is prohibited for children and
persons under the influence of alcohol, drugs or medicine.
Clearly and unequivocally define the responsibilities of the operating
and maintenance personnel.
Clearly and unequivocally define the responsibilities on the job site,
also in view of traffic regulations.
Give the operator the authority to refuse instructions by other persons
that are contrary to safety.
Have the vehicle serviced and repaired only by an authorized service
center.
Required knowledge of operator
The operator is responsible for other persons.
Avoid any operational mode that might be prejudicial to safety.
The specific national driving license is required.
The vehicle may only be operated by authorized and safety-conscious
persons who are fully aware of the risks involved in operating the
vehicle.
The operator and owner are obligated to operate the vehicle only in a
safe and working condition.
All persons working on or with the vehicle must have read and under-
stood the safety instructions in this Operator’s Manual before starting
work.
Follow, and instruct the operator in, legal and other mandatory regula-
tions relevant to accident prevention.
Observe and instruct the operator in regulations regarding road traffic
and environmental protection.
Use only the defined accesses for getting on and off the vehicle.
Be familiar with the emergency exit of the machine.
Preparatory measures for the operator
Before starting, check the vehicle whether it can be driven and
operated safely.
Tie back long hair and remove all jewelry.
Wear close-fitting work clothes that do not hinder movement.
BA TH522 * 01/2018 * BA_TH522_2_Sicherheit_us.fm * [us]
2-3
Safety 2
2.3 Conduct
Prerequisites for operation
The vehicle has been designed and built in accordance with state-of-
the-art standards and the recognized safety regulations.
Nevertheless its use can cause danger to the operator or other
persons, or damage to the vehicle.
Store this Operator’s Manual in the place provided for this in or on the
vehicle. Immediately replace a damaged or illegible Operator’s Manual
and any supplements to it.
The vehicle must only be operated in accordance with its designated
use and the instructions set forth in this Operator’s Manual.
The operator and owner are obligated not to put into operation or
operate a damaged or malfunctioning vehicle.
- If a damage or malfunction occurs during operation, put the vehicle
out of operation immediately and secure it against restart.
- Have all malfunctions jeopardizing the safety of the operator or other
persons immediately repaired by an authorized service center.
Do not put the vehicle into operation or operate it after an accident;
have it inspected for damage by an authorized service center.
- Have the seat belt replaced by an authorized service center after an
accident, even if there is no visible damage.
- Cabin and protective structures
Remove all dirt, snow and ice from climbing aids (for example,
handholds, footholds, handrails).
The owner is responsible for requiring the operating and maintenance
personnel to wear protective clothing and equipment as required by the
circumstances.
2-4
BA TH522 * 01/2018 * BA_TH522_2_Sicherheit_us.fm * [us]
2 Safety
2.4 Operating
Preparatory measures
Operation is only allowed with correctly installed and intact protective
structures.
Keep the vehicle clean. This reduces injury, accident and fire hazards.
Safely store objects you carry with you in the places provided for this
(for example, in the storage compartment, drinks holder).
Do not carry objects with you that protrude into the operator’s work
space. They can create another danger in case of an accident.
Observe all safety, warning and information labels.
Start and operate the vehicle only with the seat belt fastened and only
from the place provided for this.
Check the condition and the fastening of the seat belt. Have malfunc-
tioning seat belts and mounting hardware replaced by an authorized
service center.
Before starting work, adjust the seating position so that all control
elements can be reached and fully operated.
Perform the personal adjustment at machine standstill only (for
example, of the operator's seat, steering column).
Ensure that all safety devices are properly installed and functional
before starting work.
Before starting work or after interrupting work, ensure that the brake,
steering, signaling and light systems are functional.
Before putting the machine into operation, ensure that nobody is in the
danger zone.
BA TH522 * 01/2018 * BA_TH522_2_Sicherheit_us.fm * [us]
2-5
Safety 2
Job site
The operator is responsible for other persons.
Before starting work, familiarize yourself with the job site. This applies
to, for example:
- Obstacles in the job site and vehicle travel area
- Any barriers separating the job site from public roads
- Soil weight-bearing capacity
- Existing overhead and underground lines
- Special operating conditions (for example, dust, steam, smoke,
asbestos)
The operator must know the maximum dimensions of the machine and
the attachment – see “Technical data”.
Maintain a safe distance (for example, from buildings, edges of
building pits).
During work in buildings or in enclosed areas, look out for:
- Height of the ceiling/clearances
- Width of entries/passages
- Maximum load of ceilings and floors
- Sufficient room ventilation (for example, risk of carbon monoxide
poisoning)
Use existing visual aids to stay aware of the danger zone.
In conditions of darkness and poor visibility, switch on existing work
lights and ensure that motorists are not blinded by these lights.
If the existing lights of the vehicle are not sufficient for performing work
safely, ensure additional lighting of the job site.
Due to hot machine parts, maintain a safe distance from easily
flammable material (for example, from hay, dry leaves).
Danger zone
The danger zone is the area in which persons are in danger due to the
movements of the machine, attachment and/or load.
The danger zone also includes the area that can be affected by falling
material, equipment or by parts that are thrown out.
Extend the danger zone sufficiently in the immediate vicinity of
buildings, scaffolds or other elements of construction.
Seal off the danger zone should it not be possible to keep a sufficient
safety distance.
Stop vehicle operation immediately if persons do not stay clear of the
danger zone.
Carrying passengers
Carrying passengers with the vehicle is PROHIBITED.
Carrying passengers on/in attachments/tools is PROHIBITED.
Carrying passengers on/in trailers is PROHIBITED.
2-6
BA TH522 * 01/2018 * BA_TH522_2_Sicherheit_us.fm * [us]
2 Safety
Mechanical integrity
The operator and owner are obligated to operate the vehicle only in a
safe and working condition.
Operate the machine only if all protective and safety-oriented
equipment (for example, protective structures such as a cabin or
rollbar, removable safety devices) is installed and functional.
Check the vehicle for visible damage and defects.
In case of damage and/or unusual behavior, put the vehicle out of
operation immediately and secure it against restart.
Have all malfunctions jeopardizing the safety of the operator or other
persons immediately repaired by an authorized service center.
Starting the engine of the machine
Start the engine only according to the Operator’s Manual.
Observe all warning and indicator lights.
Do not use any liquid or gaseous starting aids (for example, ether or
starting fuel).
Machine operation
Start and operate the vehicle only with the seat belt fastened and only
from the place provided for this.
Put the vehicle into operation only if visibility is sufficient (have another
person guide you if necessary).
Operation on slopes:
- Travel/work only uphill or downhill.
- Avoid machine travel across a slope, observe the machine’s permis-
sible inclination (and of the trailer if necessary).
- Keep loads on the uphill side of the vehicle and as close as possible
to it.
- Keep attachments/work equipment close to the ground.
Adapt the travel speed to the circumstances (for example, the ground
conditions, weather conditions).
There is increased danger during backward vehicle travel. Persons in
the blind spot of the machine cannot be seen by the operator.
- Ensure that nobody is in the danger zone when you change the
travel direction.
Never get on a moving vehicle and never jump off the vehicle.
BA TH522 * 01/2018 * BA_TH522_2_Sicherheit_us.fm * [us]
2-7
Safety 2
Machine travel on public roads/sites
The specific national driving license is required.
Observe the national regulations (for example, the road traffic regula-
tions) during machine travel on public roads/sites.
Ensure that the vehicle is in compliance with the national regulations.
In order not to blind other motorists, using the existing work lights
during vehicle travel on public roads/site is prohibited.
When crossing for example, underpasses, bridges, tunnels, ensure
that the clearance height and width is sufficient.
The attachment fitted onto the machine must be certified for travel on
public roads/sites (see for example, the registration documents).
The attachment fitted onto the vehicle must be empty and in transport
position.
The attachment fitted onto the vehicle must be equipped with the
mandatory lights and protective equipment.
Take measures against unintentional operation of the operating
hydraulics.
If the vehicle has different steering modes, ensure that the mandatory
steering mode is selected.
Stopping the engine of the machine
Stop the engine only according to the Operator’s Manual.
Before stopping the engine, lower the work equipment/attachment to
the ground.
Stopping and securing the vehicle
Unbuckle the seat belt only after stopping the engine.
Before leaving the machine, secure it to prevent it from rolling away
(for example, with the parking brake, suitable wheel chocks).
Remove the starting key and secure the vehicle against unauthorized
operation.
2-8
BA TH522 * 01/2018 * BA_TH522_2_Sicherheit_us.fm * [us]
2 Safety
2.5 Lifting gear applications
Requirements
Have loads fastened and the operator guided by a qualified person
having specific knowledge of lifting gear applications and the usual
hand signals.
The person giving instructions to the operator must stay in visual
contact with the operator when fastening, guiding or removing the load
(maintain visual contact).
If this not be possible, ask one more person with the same qualifica-
tions to guide.
The operator may not leave his seat as long as the load is raised.
Fastening, guiding and removing loads
Follow the applicable specific regulations for fastening, guiding and
removing a load.
Wear protective clothing and equipment when fastening, guiding and
removing loads (for example a hard hat, safety glasses, protective
gloves, safety boots).
Do not place lifting and fastening gear over sharp edges or rotating
parts. Loads must be fastened so as to prevent them from slipping or
falling.
Move loads only on horizontal, level and firm ground.
Move loads close to the ground.
In order to avoid oscillating movements of loads:
- Perform smooth, slow movements with the vehicle.
- Use cables to guide the load (do not use hands to guide).
- Bear in mind the weather conditions (for example, the wind force).
- Keep a minimum safety distance from objects.
The operator may allow the load to be fastened and removed only if
the vehicle and its work equipment are not being moved.
Danger zones must not overlap with the work zones of other vehicles.
BA TH522 * 01/2018 * BA_TH522_2_Sicherheit_us.fm * [us]
2-9
Safety 2
Lifting gear applications
The vehicle must be certified for lifting gear applications.
Observe the national regulations for lifting gear applications.
Lifting gear applications are procedures involving raising, transporting
and lowering loads with the help of lifting and fastening gear.
The help of an accompanying person is necessary for fastening,
guiding and removing the load.
There must be nobody under the load.
Stop the vehicle immediately and stop the engine if persons enter the
danger zone.
Use the machine for lifting gear applications ONLY if the mandatory
lifting gear (for example, a joint rod and load hook) and safety
equipment (for example, optical and acoustic warning devices, hose
burst valve, stability table) is installed and functional.
Use only lifting and fastening gear certified by a test/certification body,
observe the inspection intervals (Use only chains and shackles. No
belts, slings or cables).
Do not use any lifting and fastening gear that is dirty, damaged or not
of sufficient size.
Do not interrupt the work process with a load attached.
2-10
BA TH522 * 01/2018 * BA_TH522_2_Sicherheit_us.fm * [us]
2 Safety
2.6 Trailer operation
Trailer operation
The vehicle must be certified for trailer operation.
Observe the national regulations for trailer operation.
The specific national driving license is required.
Carrying passengers on/in trailers is PROHIBITED.
Observe the maximum permissible vertical and trailer load.
Do not exceed the permissible trailer speed.
Trailer operation with the towing gear of the machine is prohibited.
Trailer operation changes the machine’s operating behavior, the
operator must be familiar with this and act accordingly.
Bear in mind the machine’s steering mode and the trailer’s turning
circle.
Before hitching/unhitching the trailer, secure it to prevent it from rolling
away (for example, with the parking brake, suitable wheel chocks).
There must be nobody between the vehicle and the trailer when
hitching a trailer.
Hitch the trailer onto the vehicle correctly.
Ensure that all equipment works correctly (for example, the brakes,
lights).
Before starting vehicle travel, ensure that nobody is between the
vehicle and the trailer.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206
  • Page 207 207
  • Page 208 208
  • Page 209 209
  • Page 210 210
  • Page 211 211
  • Page 212 212
  • Page 213 213
  • Page 214 214
  • Page 215 215
  • Page 216 216
  • Page 217 217
  • Page 218 218
  • Page 219 219
  • Page 220 220
  • Page 221 221
  • Page 222 222
  • Page 223 223
  • Page 224 224
  • Page 225 225
  • Page 226 226
  • Page 227 227
  • Page 228 228
  • Page 229 229
  • Page 230 230
  • Page 231 231
  • Page 232 232
  • Page 233 233
  • Page 234 234
  • Page 235 235
  • Page 236 236
  • Page 237 237
  • Page 238 238
  • Page 239 239
  • Page 240 240
  • Page 241 241
  • Page 242 242
  • Page 243 243
  • Page 244 244
  • Page 245 245
  • Page 246 246
  • Page 247 247
  • Page 248 248
  • Page 249 249
  • Page 250 250
  • Page 251 251
  • Page 252 252
  • Page 253 253
  • Page 254 254
  • Page 255 255
  • Page 256 256
  • Page 257 257
  • Page 258 258
  • Page 259 259
  • Page 260 260
  • Page 261 261
  • Page 262 262
  • Page 263 263
  • Page 264 264
  • Page 265 265
  • Page 266 266
  • Page 267 267
  • Page 268 268
  • Page 269 269
  • Page 270 270
  • Page 271 271
  • Page 272 272
  • Page 273 273
  • Page 274 274
  • Page 275 275
  • Page 276 276
  • Page 277 277
  • Page 278 278
  • Page 279 279
  • Page 280 280
  • Page 281 281
  • Page 282 282
  • Page 283 283
  • Page 284 284
  • Page 285 285
  • Page 286 286
  • Page 287 287
  • Page 288 288
  • Page 289 289
  • Page 290 290
  • Page 291 291
  • Page 292 292
  • Page 293 293
  • Page 294 294
  • Page 295 295
  • Page 296 296
  • Page 297 297
  • Page 298 298
  • Page 299 299
  • Page 300 300
  • Page 301 301
  • Page 302 302
  • Page 303 303
  • Page 304 304
  • Page 305 305
  • Page 306 306
  • Page 307 307
  • Page 308 308
  • Page 309 309
  • Page 310 310
  • Page 311 311
  • Page 312 312
  • Page 313 313
  • Page 314 314
  • Page 315 315
  • Page 316 316
  • Page 317 317
  • Page 318 318
  • Page 319 319
  • Page 320 320
  • Page 321 321
  • Page 322 322
  • Page 323 323
  • Page 324 324
  • Page 325 325
  • Page 326 326
  • Page 327 327
  • Page 328 328
  • Page 329 329
  • Page 330 330
  • Page 331 331
  • Page 332 332
  • Page 333 333
  • Page 334 334
  • Page 335 335
  • Page 336 336
  • Page 337 337
  • Page 338 338
  • Page 339 339
  • Page 340 340
  • Page 341 341
  • Page 342 342
  • Page 343 343
  • Page 344 344
  • Page 345 345
  • Page 346 346
  • Page 347 347
  • Page 348 348
  • Page 349 349
  • Page 350 350
  • Page 351 351
  • Page 352 352
  • Page 353 353
  • Page 354 354
  • Page 355 355
  • Page 356 356
  • Page 357 357
  • Page 358 358
  • Page 359 359
  • Page 360 360
  • Page 361 361
  • Page 362 362
  • Page 363 363
  • Page 364 364
  • Page 365 365
  • Page 366 366
  • Page 367 367
  • Page 368 368
  • Page 369 369
  • Page 370 370
  • Page 371 371
  • Page 372 372
  • Page 373 373
  • Page 374 374
  • Page 375 375
  • Page 376 376
  • Page 377 377
  • Page 378 378
  • Page 379 379
  • Page 380 380
  • Page 381 381
  • Page 382 382
  • Page 383 383
  • Page 384 384
  • Page 385 385
  • Page 386 386
  • Page 387 387
  • Page 388 388
  • Page 389 389
  • Page 390 390
  • Page 391 391
  • Page 392 392
  • Page 393 393
  • Page 394 394
  • Page 395 395
  • Page 396 396
  • Page 397 397
  • Page 398 398
  • Page 399 399
  • Page 400 400
  • Page 401 401
  • Page 402 402
  • Page 403 403
  • Page 404 404
  • Page 405 405
  • Page 406 406
  • Page 407 407
  • Page 408 408
  • Page 409 409
  • Page 410 410
  • Page 411 411
  • Page 412 412
  • Page 413 413
  • Page 414 414
  • Page 415 415
  • Page 416 416
  • Page 417 417
  • Page 418 418
  • Page 419 419
  • Page 420 420
  • Page 421 421
  • Page 422 422
  • Page 423 423
  • Page 424 424
  • Page 425 425
  • Page 426 426
  • Page 427 427
  • Page 428 428
  • Page 429 429
  • Page 430 430
  • Page 431 431
  • Page 432 432
  • Page 433 433
  • Page 434 434
  • Page 435 435
  • Page 436 436
  • Page 437 437
  • Page 438 438
  • Page 439 439
  • Page 440 440
  • Page 441 441
  • Page 442 442
  • Page 443 443
  • Page 444 444
  • Page 445 445
  • Page 446 446
  • Page 447 447
  • Page 448 448
  • Page 449 449
  • Page 450 450
  • Page 451 451
  • Page 452 452
  • Page 453 453
  • Page 454 454
  • Page 455 455
  • Page 456 456
  • Page 457 457
  • Page 458 458
  • Page 459 459
  • Page 460 460
  • Page 461 461
  • Page 462 462
  • Page 463 463
  • Page 464 464
  • Page 465 465
  • Page 466 466
  • Page 467 467
  • Page 468 468
  • Page 469 469
  • Page 470 470
  • Page 471 471
  • Page 472 472
  • Page 473 473
  • Page 474 474
  • Page 475 475
  • Page 476 476
  • Page 477 477
  • Page 478 478
  • Page 479 479
  • Page 480 480
  • Page 481 481
  • Page 482 482
  • Page 483 483
  • Page 484 484
  • Page 485 485
  • Page 486 486
  • Page 487 487
  • Page 488 488
  • Page 489 489
  • Page 490 490
  • Page 491 491
  • Page 492 492
  • Page 493 493
  • Page 494 494
  • Page 495 495
  • Page 496 496
  • Page 497 497
  • Page 498 498
  • Page 499 499
  • Page 500 500
  • Page 501 501
  • Page 502 502
  • Page 503 503
  • Page 504 504
  • Page 505 505
  • Page 506 506
  • Page 507 507
  • Page 508 508
  • Page 509 509
  • Page 510 510
  • Page 511 511
  • Page 512 512
  • Page 513 513
  • Page 514 514
  • Page 515 515
  • Page 516 516
  • Page 517 517
  • Page 518 518
  • Page 519 519
  • Page 520 520
  • Page 521 521
  • Page 522 522
  • Page 523 523
  • Page 524 524
  • Page 525 525
  • Page 526 526
  • Page 527 527
  • Page 528 528
  • Page 529 529
  • Page 530 530
  • Page 531 531
  • Page 532 532
  • Page 533 533
  • Page 534 534
  • Page 535 535
  • Page 536 536
  • Page 537 537
  • Page 538 538
  • Page 539 539
  • Page 540 540
  • Page 541 541
  • Page 542 542
  • Page 543 543
  • Page 544 544
  • Page 545 545
  • Page 546 546
  • Page 547 547
  • Page 548 548
  • Page 549 549
  • Page 550 550
  • Page 551 551
  • Page 552 552
  • Page 553 553
  • Page 554 554
  • Page 555 555
  • Page 556 556
  • Page 557 557
  • Page 558 558
  • Page 559 559
  • Page 560 560
  • Page 561 561
  • Page 562 562
  • Page 563 563
  • Page 564 564
  • Page 565 565
  • Page 566 566
  • Page 567 567
  • Page 568 568
  • Page 569 569
  • Page 570 570
  • Page 571 571
  • Page 572 572
  • Page 573 573
  • Page 574 574
  • Page 575 575
  • Page 576 576
  • Page 577 577
  • Page 578 578
  • Page 579 579
  • Page 580 580
  • Page 581 581
  • Page 582 582
  • Page 583 583
  • Page 584 584
  • Page 585 585
  • Page 586 586
  • Page 587 587
  • Page 588 588
  • Page 589 589
  • Page 590 590
  • Page 591 591
  • Page 592 592
  • Page 593 593
  • Page 594 594
  • Page 595 595
  • Page 596 596
  • Page 597 597
  • Page 598 598
  • Page 599 599
  • Page 600 600
  • Page 601 601
  • Page 602 602
  • Page 603 603
  • Page 604 604
  • Page 605 605
  • Page 606 606
  • Page 607 607
  • Page 608 608
  • Page 609 609
  • Page 610 610
  • Page 611 611
  • Page 612 612
  • Page 613 613
  • Page 614 614

Wacker Neuson TH522 (TL48-01) Manuel utilisateur

Taper
Manuel utilisateur
Ce manuel convient également à

dans d''autres langues