Amprobe CO2-100 CO2 Meter Manuel utilisateur

CO2-100

CO2 Meter

ENG FRE

GER

User Manual

ITA SPA

CO2-100

CO2 Meter

User Manual

1/2018, Rev.B

English

Limited Warranty and Limitation of Liability

Your Amprobe product will be free from defects in material

and workmanship for 1 year from the date of purchase. This

warranty does not cover fuses, disposable batteries or damage

from accident, neglect, misuse, alteration, contamination, or

abnormal conditions of operation or handling. Resellers are not

authorized to extend any other warranty on Amprobe’s behalf.

To obtain service during the warranty period, return the product

with proof of purchase to an authorized Amprobe Test Tools

Service Center or to an Amprobe dealer or distributor. See Repair

Section for details. THIS WARRANTY IS YOUR ONLY REMEDY.

ALL OTHER WARRANTIES - WHETHER EXPRESS, IMPLIED OR

STAUTORY - INCLUDING IMPLIED WARRANTIES OF FITNESS FOR

A PARTICULAR PURPOSE OR MERCHANTABILITY, ARE HEREBY

DISCLAIMED. MANUFACTURER SHALL NOT BE LIABLE FOR ANY

SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES

OR LOSSES, ARISING FROM ANY CAUSE OR THEORY. Since some

states or countries do not allow the exclusion or limitation of an

implied warranty or of incidental or consequential damages, this

limitation of liability may not apply to you.

Repair

All test tools returned for warranty or non-warranty repair or

for calibration should be accompanied by the following: your

name, company’s name, address, telephone number, and proof of

purchase. Additionally, please include a brief description of the

problem or the service requested and include the test leads with

the meter. Non-warranty repair or replacement charges should be

remitted in the form of a check, a money order, credit card with

expiration date, or a purchase order made payable to Amprobe®

Test Tools.

In-Warranty Repairs and Replacement – All Countries

Please read the warranty statement and check your battery before

requesting repair. During the warranty period any defective test

tool can be returned to your Amprobe® Test Tools distributor

for an exchange for the same or like product. Please check the

“Where to Buy” section on www.amprobe.com for a list of

distributors near you. Additionally, in the United States and

Canada In-Warranty repair and replacement units can also be sent

to a Amprobe® Test Tools Service Center (see address below).

Non-Warranty Repairs and Replacement – US and Canada

Non-warranty repairs in the United States and Canada should be

sent to a Amprobe® Test Tools Service Center. Call Amprobe® Test

Tools or inquire at your point of purchase for current repair and

replacement rates.

In USA In Canada

Amprobe Test Tools Amprobe Test Tools

Everett, WA 98203 Mississauga, ON L4Z 1X9

Tel: 877-AMPROBE (267-7623) Tel: 905-890-7600

Non-Warranty Repairs and Replacement – Europe

European non-warranty units can be replaced by your Amprobe®

Test Tools distributor for a nominalv charge. Please check the

“Where to Buy” section on www.amprobe.com for a list of

distributors near you.

European Correspondence Address*

Amprobe® Test Tools Europe

In den Engematten 14

79286 Glottertal, Germany

Tel.: +49 (0) 7684 8009 - 0

*(Correspondence only – no repair or replacement available from

this address. European customers please contact your distributor.)

CO2-100 CO2 Meter

1

3

5

7

9

11

Humidity Sensor

LCD Display

Backlight/Roll Up Key

Temp. Mode/Roll Down Key

Min/Max/Avg./Enter Key

DC Adaptor Port

2

3

9

7

5

1

4

6

8

10

11

2

4

6

8

10

CO2 Sensor (Rear Side)

POWER/SET Key

Calibration/Escape Key

Data Hold Key

USB Port

LCD Display

1

2

3

8

9

4 56 7

10

11 12

Primary Screen Displays CO2 Concentration

Relative Humidity In %

Air, Dew Point, Wet Bulb Temperature Display

Co2 Measurement Mode

Unit For Co2 Concentration

Time Weighted Average (8 Hours)

Short-Term Exposure Limit

(15 Minutes Weighted Average)

To Freeze Readings

Minimum/Maximun Readings

Low Battery Indicator

Dew Point Temperature

Wet Bulb Temperature

12

1

2

3

4

5

7

9

10

11

6

8

1

CONTENTS

SYMBOLS .......................................................................... 2

UNPACKING AND INSPECTION .......................................2

INTRODUCTION ................................................................3

Features ........................................................................3

OPERATION ....................................................................... 4

Auto Power Off ........................................................... 5

Setup ............................................................................6

Calibration Mode ........................................................ 7

USB Interface capabilities ........................................... 8

SPECIFICATION .................................................................9

MAINTENANCE AND REPAIR ...........................................10

Battery Replacement ..................................................10

TROUBLE SHOOTING .......................................................11

APPENDIX ........................................................................12

2

SYMBOLS



Caution! Refer to the explanation in this

Manual

Conforms to relevant Australian standards



Complies with European Directives



Do not dispose of this clamp meter as

unsorted municipal waste. Contact a qualified

recycler for disposal.



Warning and Precautions

• Avoid condensation on CO2 sensor

• Do not hold the meter close to faces in case

exhalation affects CO2 levels.

• Do not calibrate the meter in the air with

unknown CO2 concentration. Otherwise, it will

be calibrated as 400ppm by default and leads to

inaccurate measurements.

UNPACKING AND INSPECTION

Your shipping carton should include:

1 CO2-100 CO2 Meter

4 AA battery

1 User manual

1 Hard carrying case

If any of the items are damaged or missing, return

the complete package to the place of purchase for an

exchange.

3

INTRODUCTION

Thank you for purchasing this portable CO2 meter. The

meter measures CO2 level, air temp., dew point, wet

bulb temp. and humidity and is an ideal instrument for

indoor air quality (IAQ) diagnosis.

Poor indoor air quality is considered unhealthy because

it causes tiredness, loss of ability to concentrate, and

even illness (ex. Sick Building Syndrome). IAQ monitoring

and survey, especially on CO2 level and air ventilation

become widely applied in public areas such as offices,

classrooms, factories, hospitals and hotels. It is also

suggested in regulations of industrial hygiene in some

countries. (Appendix)

The portable CO2 meter uses NDIR (non-dispersive

infrared) technology to ensure the reliability and long

term stability. It’s useful in verifying HVAC system

performance and air ventilation control

Features

• Triple displays of CO2 level, temp. and humidity.

• Stable NDIR sensor for CO2 detection.

• Statistics of weighted averages (TWA & STEL)

• Backlight for working in dark area

• Audile CO2 warning alarm

• Battery and adaptor power supply

• Easy manual calibration on CO2 and humidity

• USB PC connection

4

OPERATION

1. Press “POWER/SET” to turn instrument on and off.

At power up, it emits a short beep and performs

30 seconds countdown for meter warm up, then

enters normal mode.

2. The meter starts measurement when power

on and update readings every second. In the

condition of operating environment change (ex.

from high to low temp.), it takes 30 sec to respond

for CO2 sensor and 30 minutes for RH.

3. Press “DP/WBT” to switch temperatures

display. The lower left display will cycle from air

temperature, dew point temp., and wet bulb

temp. (Fig.1)

Fig.1

4. Press “HOLD” to freeze the readings, “HOLD”

icon is displayed on the left top of LCD. All current

readings are kept unchanged, except STEL and

TWA. Press “HOLD” again to cancel data hold

function.

5. Hold down “MODE/p”for more than 1 second to

activate and cancel backlight.

6. Press “MAX/MIN” to see the minimum, maximum,

and weighted average readings. Each press of it

displays MIN, MAX, STEL, TWA in sequence and

returns to normal mode. In MIN and MAX modes,

it shows the minimum and maximum readings

of CO2 on main display, and of AIR/DP/WBT

temperatures and humidity on the lower displays.

5

In STEL and TWA modes, the main display shows

the weighted average of CO2 readings for the past

15 minutes (STEL) and 8 hours(TWA), but the lower

displays are the current AIR, DP/WB temperatures

and humidity readings.

NOTE:

• If the meter is turned on for shorter than 15

minutes, the STEL value will be the weighted

average of readings taken since power on. Same

for TWA values appear before 8 hours.

• It takes at least 5 minutes to calculate STEL and

TWA. The display shows “----” during the first 5

minutes from power on (Fig.2).

Fig.2

• While all readings are held unchanged, STEL

and TWA will keep updating every 5 minutes.

7. The instrument emits beeps (Abt.80dB) when CO2

level goes over the set limit and stops when any

key (but “POWER“ key) was pressed or readings

fall below the set value. It beeps again when value

goes over the limit. Restart the meter if beeper

can’t be stopped.

Auto Power Off

The meter turns off automatically after 20 minutes of

inactivity. To override the function, hold down “POWER

/ SET” and ”HOLD” for 2 seconds to turn on the meter

until “n” appears.

6

Setup

The advanced setup mode lets you customize your meter.

2 types parameter are available.

P1.0: CO2 alarm threshold setting

P3.0: Temperature unit setting

P1.0 CO2 alarm threshold setting

Hold down “POWER/SET” under normal mode for more

than 1 sec to enter set up mode. To exit setup, press

“CAL/ESC” in P1.0 or P3.0.

When entering setup mode, P1.0 and “AL” are displayed

on the LCD (Fig.3). Press “ENTER” to go into P1.1 for

setting CO2 alarm threshold. The current set value will

be blinking on LCD (Fig.4). Press “p”to increase the

value or “q”to decrease. Each press tunes 100 ppm and

the alarm range is from 100 to 9900ppm. When the

preferred alarm value is set, press “ENTER” to save the

setting or “ESC” without saving and return to P1.0.

Fig.3 Fig.4

P3.0: Temperature unit setting

Press “p“or “q”in P1.0 to access P3.0 for setting up

temperature scale. Press “ENTER” and it goes into P3.1

with blinking °C or °F current set on the lower left

display. To switch °C or °F, press “p“or “q. Then press

“ENTER” to save the setting or “ESC” without saving and

return to P3.0.

7

Calibration Mode

CO2 calibration

1. Place the meter in an outdoor area with well

ventilated air. Turn on the meter and hold down

“CAL” and “p” simultaneously to enter CO2

calibration mode. 400ppm and “CAL” are blinking

on the LCD while performing calibration (Fig.5).

Fig.5

2. Wait about 5 minutes until it stops blinking and

the calibration completes automatically and back

to normal mode.

3. To abort the calibration, turn off the meter at any

time.

Humidity calibration

1. Plug the sensor probe into 33% salt bottle. Hold

down “CAL” and “q” under normal mode to

enter 33% calibration. “CAL” and calibrating

value (32.7% if at 25°C) are blinking on the LCD

with current temperature at the left. Meter is now

calibrating, and will finish in about 60 minutes

when “CAL” and humidity value stop blinking.

2. After 33% calibration, plug the sensor probe into

75% salt bottle, then press “ENTER” to enter 75%

calibration. “CAL” and calibrating value (75.2%

if at 25°C) are blinking on the LCD with current

temperature at the left. Meter is now calibrating.

Wait about 60 minutes until blinking stops, then

calibration is completed and it returns to normal

mode.

8

3. Users can also calibrate either point. To calibrate

33% only, press “ESC” and exit when 33%

calibration is completed. To calibrate 75%

only, press “p” or “q”within 5 minutes while

initializing 33% calibration. To abort calibration,

just turn off the meter.

USB Interface Capabilities

The USB cable and software (optional kit) are required

to transfer data to a PC. Install the USB driver in the

software first before connection.

9

SPECIFICATION

CO2

Range

0~9999ppm

(5001~9999 out of accuracy scale range)

Resolution 1 ppm

Accuracy

±30ppm±5%rdg (0~5000)

(Not specified for out of scale)

Pressure

+1.6% reading per kPa deviation from

normal

Dependence Pressure, 100kPa

Temperature

Range -10.0~60.0°C (14~140°F)

Resolution 0.1°C /0.1°F

Accuracy ±0.6°C / ±0.9°F

Humidity

Range 0.0~95%

Resolution 0.1%

Accuracy ±3%(10~90% at 25°C) ; ±5%(others)

Operating

environment

0~50°C, 0~95%RH (avoid condensation)

Storage

environment

-20~60°C, 0~99%RH

(avoid condensation)

Power supply 4pcs AA batteries

 - EMC: Conforms to EN61326-1. This product complies

with requirements of the following European Community Directives:

2014/30/EU (Electromagnetic Compatibility). However, electrical noise

or intense electromagnetic fields in the vicinity of the equipment

may disturb the measurement circuit. Measuring instruments will

also respond to unwanted signals that may be present within the

measurement circuit. Users should exercise care and take appropriate

precautions to avoid misleading results when making measurements

in the presence of electronic interference.

10

MAINTENANCE AND REPAIR

If there appears to be a malfunction during the

operation of the meter, the following steps should be

performed in order to isolate the cause of the problem.

1. Check the battery. Replace the battery

immediately when the “

” symbol appears on

the LCD.

2. Review the operating instructions for possible

mistakes in operating procedure.

Except for the replacement of the battery, repair of the

meter should be performed only by a Factory Authorized

Service Center or by other qualified instrument service

personnel. The front panel and case can be cleaned with

a mild solution of detergent and water. Apply sparingly

with a soft cloth and allow to dry completely before

using. Do not use aromatic hydrocarbons or chlorinated

solvents for cleaning.

BATTERY REPLACEMENT

1. The meter is powered by either 4 AA batteries or a

DC adaptor (9V/1A output).

2. When battery voltage gets low, “

” and “Lob”

will appear on the LCD (Fig.6). And beeper sounds.

The CO2 sensor can’t work under low voltage, so it

beeps to indicate failed CO2 measurement and the

readings won’t be displayed. Please replace with

fresh batteries or connect with an adaptor.

11

TROUBLE SHOOTING

Can’t power on

• Make sure you press power key more than 0.3

second.

• Check the battery conditions and replace if

necessary.

• Check whether the adaptor is well plugged.

• Move batteries away for one minute and then

re-install.

Display disappear

• Check whether the low battery icon is appeared

before the display is off. If yes, replace with new

batteries.

Fixed readings

• Check whether data hold function was activated.

(HOLD icon at the left top)

Slow response

• Check whether the air flow channels on the rear

were blocked

Error code

E01: CO2 sensor damaged.

E02: The value is under range.

E03: The value is over range.

E04: The original data error results in this error

(DP, WB)

E07: Too low voltage to measure CO2. Replace

batteries or use an adaptor.

E11: Retry humidity calibration.

E17: Retry CO2 calibration.

E31: Temperature sensor damaged.

E34: Humidity sensor damaged.

12

APPENDIX - CO2 LEVELS AND GUIDELINES

NIOSH recommendations

250-350 ppm: normal outdoor ambient concentrations

600 ppm: minimal air quality complaints

600-1000 ppm: less clearly interpreted

1000 ppm: indicates inadequate ventilation; complaints

such as headaches, fatigue, and eye/throat irritation will

be more widespread. 1000 ppm should be used as an

upper limit for indoor levels.

ASHRAE Standard 62-1989: 1000ppm

CO2 concentration in occupied building should not

exceed 1000ppm.

Building bulletin 101 (BB101): 1500ppm

UK standards for schools say that CO2 at averaged over

the whole day(i.e. 9am to 3.30pm) should not exceed

1500ppm.

OSHA: 5000ppm

Time weighted average over five 8-hour work days

should not exceed 5000ppm.

Germany, Japan, Australia, UK...: 5000ppm

8 hours weighted average in occupational exposure limit

is 5000ppm.

La page charge ...

Amprobe CO2-100 CO2 Meter Manuel utilisateur

Amprobe CO2-100 CO2 Meter Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents