Yamaha YSP-2200 Manuel utilisateur

Marque: Yamaha

Modèle: YSP-2200

Catégorie: Destinataire

Taper: Manuel utilisateur

(YSP-CU2200 + NS-SWP600)

Digital Sound Projector™

OWNER’S MANUAL

English

i En

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

1 To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 Install this unit in a well ventilated, cool, dry, clean place –

away from direct sunlight, heat sources, vibration, dust,

moisture, and/or cold. For proper ventilation, allow the

following minimum clearances.

Top : 5 cm (2 in)

Rear: 5 cm (2 in)

Sides: 1 cm (13/32 in)

3 Locate this unit away from other electrical appliances,

motors, or transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes from

cold to hot, and do not locate this unit in an environment with

high humidity (i.e. a room with a humidifier) to prevent

condensation inside this unit, which may cause an electrical

shock, fire, damage to this unit, and/or personal injury.

5 Avoid installing this unit where foreign object may fall onto

this unit and/or this unit may be exposed to liquid dripping or

splashing. On the top of this unit, do not place:

– Other components, as they may cause damage and/or

discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire,

damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall and

liquid may cause electrical shock to the user and/or

damage to this unit.

6 Do not cover this unit with a newspaper, tablecloth, curtain,

etc. in order not to obstruct heat radiation. If the temperature

inside this unit rises, it may cause fire, damage to this unit,

and/or personal injury.

7 Do not plug in this unit to a wall outlet until all connections

are complete.

8 Do not operate this unit upside-down. It may overheat,

possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cable from the wall outlet,

grasp the plug; do not pull the cable.

11 Do not clean this unit with chemical solvents; this might

damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used. Using this

unit with a higher voltage than specified is dangerous and

may cause fire, damage to this unit, and/or personal injury.

Yamaha will not be held responsible for any damage resulting

from use of this unit with a voltage other than specified.

13 To prevent damage by lightning, keep the power cable

disconnected from a wall outlet or this unit during a lightning

storm.

14 Do not attempt to modify or fix this unit. Contact qualified

Yamaha service personnel when any service is needed. The

cabinet should never be opened for any reasons.

15 When not planning to use this unit for long periods of time

(i.e. vacation), disconnect the AC power plug from the wall

outlet.

16 Be sure to read the “TROUBLESHOOTING” section on

common operating errors before concluding that this unit is

faulty.

17 Before moving this unit, press p to set this unit to the

standby mode, and disconnect the AC power plug from the

wall outlet.

18 Condensation will form when the surrounding temperature

changes suddenly. Disconnect the power cable from the

outlet, then leave this unit alone.

19 When using this unit for a long time, this unit may become

warm. Turn the power off, then leave this unit alone for

cooling.

20 Install this unit near the AC outlet and where the AC power

plug can be reached easily.

21 The batteries shall not be exposed to excessive heat such as

sunshine, fire or the like. When you dispose of batteries,

follow your regional regulations.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO

NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

WARNING

THE POWER SUPPLY CABLE OF THIS UNIT MUST BE

CONNECTED TO THE MAIN SOCKET OUTLET VIA A

PROTECTIVE EARTHING CONNECTION.

This unit is not disconnected from the AC power source as long as

it is connected to the wall outlet, even if this unit itself is turned off

by p. This state is called the standby mode. In this state, this unit

is designed to consume a very small quantity of power.

ii En

■ For U.K. customers

If the socket outlets in the home are not suitable for the plug supplied

with this appliance, it should be cut off and an appropriate 3 pin plug

fitted. For details, refer to the instructions described below.

The plug severed from the mains lead must be destroyed, as a plug

with bared flexible cord is hazardous if engaged in a live socket outlet.

■ Special Instructions for U.K. Model

■ Notes on remote controls and batteries

• Do not spill water or other liquids on the remote control.

• Do not drop the remote control.

• Do not leave or store the remote control in the following conditions:

– places of high humidity, such as near a bath

– places of high temperatures, such as near a heater or stove

– places of extremely low temperatures

– dusty places

• Insert the battery according to the polarity markings (+ and -).

• Change all batteries if you notice the following conditions: the

operation range of the remote control narrows or the transmit

indicator does not flash or is dim.

• If the batteries run out, immediately remove them from the remote

control to prevent an explosion or acid leak.

• If you find leaking batteries, discard the batteries immediately,

taking care not to touch the leaked material. If the leaked material

comes into contact with your skin or gets into your eyes or mouth,

rinse it away immediately and consult a doctor. Clean the battery

compartment thoroughly before installing new batteries.

• Do not use old batteries together with new ones. This may shorten

the life of the new batteries or cause old batteries to leak.

• Do not use different types of batteries (such as alkaline and

manganese batteries) together. Specification of batteries may be

different even though they look the same.

• Before inserting new batteries, wipe the compartment clean.

• Dispose of batteries according to your regional regulations.

Note

IMPORTANT

THE WIRES IN MAINS LEAD ARE COLOURED IN

ACCORDANCE WITH THE FOLLOWING CODE:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this apparatus may

not correspond with the coloured markings identifying the

terminals in your plug, proceed as follows:

The wire which is coloured BLUE must be connected to the

terminal which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the

terminal which is marked with the letter L or coloured RED.

Making sure that neither core is connected to the earth terminal of

the three pin plug.

1 En

2 En

What you can do with this unit

To enjoy TV

To enjoy Blu-ray

movies

To enjoy games

Checking supplied accessories (p. 4)

Installation (p. 9)

Preparing the remote control (p. 13)

Connecting your TV and Blu-ray disc player (p. 14)

Operating the unit by TV’s remote control (p. 24)

When enjoying STB program

such as on satellite/CATV tuner

(p. 15)

Connecting a game

console (p. 15)

Playing back a TV, Blu-ray disc player, and game console (p. 26)

PREPARATION

CONNECTION/

INITIAL SETTINGS

PLAYBACK

Setting the best possible sound automatically (p. 17)

HDMI link (HDMI control)

function

p. 24

Cinema DSP function

p. 28

IntelliBeam function

p. 17

UniVolume

p. 27

Playing back iPod/iPhone

p. 33

3 En

PREPARATION

CONNECTION/

INITIAL SETTINGS PLAYBACK SETTINGS

TROUBLESHOOTING

APPENDIX

Contents

PREPARATION

Getting started ....................................................... 4

Supplied accessories .................................................... 4

Controls and functions.......................................... 5

CONNECTION/INITIAL SETTINGS

Installation and Connection.................................. 9

Remote control preparation......................................... 13

Subwoofer connection................................................. 13

Connections ......................................................... 14

TV and Blu-ray disc player connection........................ 14

Game console or tuner connection ............................. 15

Initial settings....................................................... 16

Selecting language for menu display .......................... 16

Auto setup for appropriate surround effects

(IntelliBeam)................................................................ 17

Operating the unit by TV’s remote control................... 24

PLAYBACK

Playback features ................................................ 26

Basic operation for playback ....................................... 26

Enjoying sound with your preference.......................... 27

Switching stereo/surround sound.......................................27

Playing back digitally compressed formats (MP3, WMA, etc.)

with enriched sound (Compressed Music Enhancer).........27

Automatic volume level adjustment (UniVolume)...............27

Volume balance adjustment............................................... 27

Enjoying realistic surround sound (CINEMA DSP).............28

Changing the audio output method for surround playback

...........................................................................................29

Surround decoder setting...................................................31

Using useful features .................................................. 32

Sleep timer/auto power down function ............................... 32

Settings for each input source (Option menu).................... 32

Playing back iPod/iPhone ........................................... 33

When using Yamaha Universal Dock for iPod (optional

YDS-12, etc.)...................................................................... 34

When using Wireless System for iPod (optional YID-W10)

...........................................................................................34

Playing back Bluetooth components ...........................35

Pairing................................................................................ 35

Connecting......................................................................... 35

SETTINGS

Setup menu...........................................................36

Setting procedure ........................................................36

Setup menu list............................................................37

Manual setup...............................................................38

Setting parameters ........................................................... 38

Beam adjustment .............................................................. 39

Image location .................................................................. 40

Tone control ................................................................40

Tone control...................................................................... 40

Subwoofer settings ........................................................... 40

Audio delay control ........................................................... 40

Dynamic range control ...................................................... 41

Volume level of each channel with test tones ................... 41

Sound out setting ........................................................41

Sound beam output configuration ..................................... 41

Input assignment......................................................... 42

Input assignment .............................................................. 42

Input rename..................................................................... 43

HDMI setup....................................................................... 43

DISPLAY MENU ............................................................... 44

Advanced setup ...................................................45

TROUBLESHOOTING

Troubleshooting...................................................46

APPENDIX

Glossary................................................................50

Specifications.......................................................52

Using the supplied demonstration DVD.............54

Index......................................................................55

About this manual

• In this manual, operations that can be performed using either the front panel buttons or the remote control are explained using the

remote control.

•

y indicates a tip for your operation.

• Notes contain important information and operating instructions.

• This manual is produced prior to production. Design and specifications are subject to change in part as a result of improvements,

etc. In case of differences between the manual and the product, the product has priority.

• The alphabet mark (such as ) indicates the remote control key(s) indicated on the figure on the left page.

4 En

PREPARATION

Getting started

Before connecting, make sure you have received all of the following items.

Supplied accessories

Units

Accessories

Center unit (YSP-CU2200) Subwoofer (NS-SWP600)

Remote control Battery (× 2)

(AA, R6, UM-3)

Optical cable

(1.5 m (4.9 ft))

Video pin cable

(for displaying menu

and iPod video)

(1.5 m (4.9 ft))

IR Flasher

(1 m (3.3 ft))

Safety and Accessory

Information

IntelliBeam microphone

(6 m (19.7 ft))

Cardboard microphone

stand

Quick Reference Guide

Digital audio pin cable

(1.5 m (4.9 ft))

Demonstration DVD

(☞p. 54)

Stand for

subwoofer (×4)

Speaker cable

(3 m (9.8 ft))

Non-skid pad for center

unit (×4)

According to the connection, the supplied cables may not be needed.

1) y

5 En

PREPARATION

CONNECTION/

INITIAL SETTINGS PLAYBACK SETTINGS

TROUBLESHOOTING

APPENDIX

Controls and functions

1 Front panel display

Shows information about the operational status of this unit.

(☞p. 7)

2 SURROUND indicator

Lights up according to the input signal.

3 STATUS indicator

Lights up to show the system condition.

4 INTELLIBEAM jack

Connect the supplied IntelliBeam microphone for AUTO SETUP

(☞p. 17).

5 Remote control sensor

Receives infrared signals from the remote control. (☞p. 8)

6 Remote control sensor of a TV

Receives infrared signals from the remote control of your TV

when connecting the IR Flasher. (☞p. 10)

7 INPUT key

Selects playback component. (☞p. 15)

8 VOLUME +/- key

Controls the volume of the unit. (☞p. 26)

9 key

Turns on the unit or set it to the standby mode.

Controls and functions

Front panel

45 6

789

Displayed

color

Input signal

Blue Following surround audio signal formats:

Dolby TrueHD, Dolby Digital Plus, DTS-HD

Master Audio, DTS-HD High Resolution, Multi-

channel Linear PCM

Orange Surround audio signal other than above

Off Audio signal other than above or no signal

Light Power

HDMI

CONTROL

(☞p. 43)

Interlock

Mode

(☞p. 34)

Green On – –

Red Standby On –

Standby – On

Off Standby Off Off

In the standby mode, this unit consumes a small amount of

power in order to receive infrared signals from the remote

control or to search for HDMI signals.

Note

Controls and functions

6 En

1 AUDIO INPUT 3 jack

For connecting analog cable to the external components.

(☞p. 15)

2 DOCK terminal

For connecting optional Yamaha Universal Dock for iPod,

Wireless System for iPod/iPhone, and Bluetooth Wireless Audio

Receiver. (☞p. 33, 35)

3 VIDEO OUT jack

For connecting video input jack of TV to display the YSP-2200’s

setup menus on your TV or to play back video in iPod/iPhone.

(☞p. 14)

4 IR output jack

For connecting IR Flasher (supplied). (☞p. 11)

5 COAXIAL digital input 2 jack

For connecting digital audio pin cable to the external

components. (☞p. 15)

6 OPTICAL digital input 1 jack

For connecting optical cable to the external components.

(☞p. 15)

7 OPTICAL digital input TV jack

For connecting optical cable to the TV. (☞p. 14)

8 HDMI OUT (ARC) jack

For connecting HDMI compatible TV and external components.

(☞p. 14)

9 HDMI IN jack

For connecting HDMI compatible Blu-ray disc player, tuner and

game console. (☞p. 14, 15)

0 Subwoofer output terminal

For connecting the speaker cable (supplied) to subwoofer.

(☞p. 14)

a Power cable

For connecting to an AC wall outlet. (☞p. 14)

Rear panel

1234567 8 9 0A

Controls and functions

7 En

PREPARATION

CONNECTION/

INITIAL SETTINGS PLAYBACK SETTINGS

TROUBLESHOOTING

APPENDIX

1 HDMI indicator

Lights up when HDMI signal is input.

2 SLEEP indicator

Lights up when the sleep timer is set. (☞p. 32)

3 CINEMA DSP indicator

Lights up when a sound field program is selected (☞p. 28).

4 VOL indicator

Indicates the current volume level. (☞p. 26)

5 Multi information display

Displays information in alpha-numeric values.

Displays playback components and current sound output when

power is on.

Front panel display

Controls and functions

8 En

CINEMA DSP program keys

When playback is in surround sound, select the CINEMA DSP

programs (☞p. 28).

SURROUND key

Switches to surround playback. (☞p. 28)

STEREO key

Switches to stereo playback. (☞p. 27)

Input selector keys

Select playback component. (☞p. 26)

INFO key

Switches the information display on the front panel as follows.

• Input/Output: Input name/surround mode

• DSP Program: Sound field program of CINEMA DSP (only

when using CINEMA DSP)

• Audio Decoder: Sound signal decoder currently selected

SETUP key

Displays the setup menu. (☞p. 36)

MENU (U) key, ENTER key,

(Y) key, (Z) key,  (V) key

• Change the setting. (☞p. 36)

• Operate iPod.

DOCK key

Selects iPod/iPhone or Bluetooth component. (☞p. 33, 35)

RETURN key

Returns to the previous menu screen.

SUBWOOFER (+/-) key

Adjusts the volume balance of subwoofer.

SLEEP key

Sets the sleep timer. (☞p. 32)

key

Turns on the unit or set it to the standby mode. (☞p. 26)

UNIVOLUME key

Turns UniVolume mode to on/off. (☞p. 27)

ENHANCER key

Turns Compressed Music Enhancer to on/off. (☞p. 27)

OPTION key

Displays option menu for each input source. (☞p. 32)

S/T key

Operate iPod wheel. (☞p. 33).

VOLUME (+/-) key

Controls the volume of the unit. (☞p. 26)

MUTE key

Mute the sound. (☞p. 26)

CH LEVEL key

Adjusts the volume balance during playback. (☞p. 27)

Remote control

Infrared signal transmitter

9 En

CONNECTION/INITIAL SETTINGS

PREPARATION

CONNECTION/

INITIAL SETTINGS PLAYBACK SETTINGS

TROUBLESHOOTING

APPENDIX

Installation and Connection

To achieve desired surround sound effects, install this unit where there are no objects such as furniture obstructing the path of sound

beams (☞p. 11). Depending on your installation environment, connections with external components (☞p. 14) should be done before

installation.

Some of your TV have sensors such as motion sensor, or signal

transmitter for 3D glasses in front. Installing the center unit may

interrupts the sensors or signal transmitter functioning. Set the

center unit away from your TV, or install it in your rack.

Center unit

• Install this unit in the center of the left and right walls.

• Listening position (such as sofa, etc.) should be located at the front of

the unit.

• The distance between listening position and the unit should be more

than 1.8 m (5.9 ft).

Subwoofer

Install the subwoofer as close to the center unit as possible for a

better unit of sounds.

This unit creates surround sound by reflecting projected sound beams off the walls of your listening room. The surround sound effects

produced by this unit may not be sufficient when this unit is installed in the following locations.

• Rooms with walls inadequate for reflecting sound beams

• Rooms with acoustically absorbent walls

• Rooms with measurements outside the following range: W (3 to 7 m (10 to 23 ft)) × H (2 to 3.5 m (7 to 11.5 ft)) × D (3 to 7 m (10 to

23 ft))

• Rooms with less than 1.8 m (6 ft) from the listening position to this unit

• Rooms where objects such as furniture are likely to obstruct the path of sound beams

• Rooms where the listening position is close to the walls

• Rooms where the listening position is not in front of this unit

■ My Surround

In the room such as above, you can enjoy rich surround effects by My Surround (☞p. 29, 30).

Notes on installation

• Make sure you leave an adequate amount of ventilation space so that heat can escape.

• Be sure to install this unit where it will not fall subject to vibrations, such as from an earthquake, and where it is out of the reach of children.

• When using a cathode-ray tube (CRT) TV, do not install this unit directly above your TV.

• If the picture on your TV screen becomes blurred or distorted, we recommend moving this unit away from your TV.

Center unit

Subwoofer

Before installing this unit

Installation and Connection

10 En

■ Adjust the height of center unit

In case that the center unit straddles the stands of your TV,

turning the stands to left makes the unit higher. Confirm the

graduation of each stand to make each stand the same height.

Adjust the graduation in the range from 0 to 10.

■ Remove the center unit legs

When the center unit hides the remote control sensor or signal

transmitter for 3D glasses of your TV, turn the center unit over,

remove the legs, and use supplied pads as shown below.

1 Turn the leg furthermore to the left.

2 Remove the outside part of the leg.

3 Push the whole leg to the center of the bottom as

shown in the illustration while laying the hook to the

same direction, and then remove the inside part of

the leg.

4 Attach the 4 non-skid pads (supplied) to the corners

on the bottom of the center unit. (The illustration

below is one of the examples for attaching the non-

skid pads.)

■ When the center unit hides the remote

control sensor of your TV

The unit receives the signal from the remote control of your TV

in front, and transmits to your TV by IR Flasher (supplied).

Remove the backing paper on the tip of LED part of IR Flasher,

and attach it to the remote control sensor of your TV or the area

close to the remote control sensor of your TV on the rear panel of

center unit as shown. Connect the plug to the IR output jack of the

unit.

Install the subwoofer with the supplied stands. Attach the

supplied stands with the dowels to the subwoofer. Changing the

position of the stands enables both horizontal placement and

vertical placement. Horizontal placement is convenient for

installing the center of a rack, and vertical placement is

convenient for installing the side of a rack.

The graduation

Adjustable range:

28.5mm to 38.5mm

(1-1/8 in to 1-1/2 in)

Non-skid pad

Attach the stands to the subwoofer

IR Flasher (supplied)

Remote

control

sensor of

your TV

• When using IR Flasher, direct the remote control of your TV to

the center unit.

• This function is valid even in the standby mode.

• This function may not activate with some TVs.

Notes

Horizontal placement Vertical

placement

Installation and Connection

11 En

PREPARATION

CONNECTION/

INITIAL SETTINGS PLAYBACK SETTINGS

TROUBLESHOOTING

APPENDIX

This unit outputs sound beam as shown in the illustrations below. Install this unit where there are no obstacles such as furniture

obstructing the path of sound beams. Otherwise, the desired surround sound effects may not be achieved.

You may install this unit in parallel with the wall or in the corner.

■ Installation examples

Parallel installation

Install this unit as close to the exact center of the wall as possible.

Ideal installation condition

Install this unit as close to the exact front of your normal listening position as possible.

The distance between listening position and the unit should be more than 1.8 m (6 ft).

Installing this unit

Parallel installation

Install this unit in the exact center of the wall when it is measured

from the left and right corners.

Corner installation

Install this unit in the corner at a 40° to 50° angle from the

adjacent walls.

An object, such as furniture

40° to 50°

Parallel installation

(with 5Beam)

Corner installation

(with Stereo+3Beam)

Installation and Connection

12 En

Installing in a non-square room

Install this unit so that the sound beams can be reflected off the walls.

Example for installing the unit in living room

• As surround beams normally pass through tables, tables are not

obstacles. And a cupboard installed facing the wall reflects

sounds.

• In a case of the listening room as right illustration, adjusting the

position of right channel after auto setup enables to achieve

more desired surround sound effects. (☞p. 38)

• As the curtains absorb sounds, the sound features of the

listening room is different from the case with the curtain opened

and the case with the curtain closed. Using saving settings

function enables to save the best settings for each case of

listening room. (☞p. 22)

Installation and Connection

13 En

PREPARATION

CONNECTION/

INITIAL SETTINGS PLAYBACK SETTINGS

TROUBLESHOOTING

APPENDIX

Before installing batteries or using the remote control, make sure that you read precautions on the remote control and batteries in

“CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.”

Remote control preparation

Installing the batteries

Battery × 2

(AA, R6, UM-3)

Press U

Remove the transparent sheet before using.

Operation range

Within 6 m (20 ft)

Subwoofer connection

• Make sure to connect the subwoofer (supplied).

• Do not connect a subwoofer except the supplied one.

• Match the positive (+) of the subwoofer terminal to the positive (+) of the center unit terminal, and the negative (-) of the subwoofer terminal to

the negative (-) of the center unit terminal when connecting the speaker cable (supplied).

Twist and pull off the

insulation tube on the lead

wire.

Insert into the terminal on

the rear panel.

14 En

Connections

For the cable connection, follow the orders below.

TV and Blu-ray disc player connection

HDMI cable

(optional)

Input the digital audio/

video signals of the Blu-

ray disc player to this

unit.

HDMI cable

(optional)

The digital video of the

Blu-ray disc is reflected

on TV.

Optical cable

(supplied)

Play back digital sounds

of TV on this unit.

Video pin cable

(supplied)

To display the YSP-

2200’s setup menus on

the TV.

• Do not connect the power cable until all connections are completed.

• Do not use excessive force when inserting the cable plug. Doing so may damage the cable plug and/or terminal.

123

INPUT1

HDMI INPUT

OPTICAL

OUTPUT

VIDEO

AUDIORL

HDMI

OUTPUT

To AC wall outlet

Blu-ray disc player

1. Remove the cap

2. Check the direction

of the plug

Video signals

Audio signals

(Example)

Subwoofer (supplied)

Connect the center unit with the speaker cable

(supplied) to the subwoofer. (☞p. 13).

Audio return channel (ARC) supported TV

• Connect HDMI cable to audio return channel supported terminal (the

terminal with “ARC” indicated) on TV. In this case, you do not need

to connect optical cable.

• Activate the HDMI control function of this unit so as to activate audio

return channel (ARC) (☞p. 43).

What is audio return channel (ARC)?

A function transmits digital audio signal output from TV to this unit

through a HDMI cable. By this function, a digital audio pin cable to

connect TV and this unit is not needed.

Depending on the setting, HDMI for video signal and optical digital

audio, coaxial digital audio or analog audio for audio signal can be

selected. Refer to “Input assignment (☞p. 42)”.

1) y

2) y

15 En

Connections

PREPARATION

CONNECTION/

INITIAL SETTINGS PLAYBACK SETTINGS

TROUBLESHOOTING

APPENDIX

Game console or tuner connection

Additional external device (example) Connecting cable

1 HDMI supported game console

HDMI cable (optional)

2 Satellite/cable TV (HDMI supported)

HDMI cable (optional)

3 Satellite/cable TV (HDMI not supported)

Digital audio pin cable (supplied)

4 HDMI not supported game console

Analog audio stereo pin cable (optional)

ANALOG

OUTPUT

COAXIAL

OUTPUT

HDMI

OUTPUT

HDMI

OUTPUT

VIDEO

INPUT

VIDEO

INPUT

VIDEO

OUTPUT

VIDEO

OUTPUT

Video signals

Audio signals

(Example)

2 3

(Example)

The additional devices having an optical digital output jack, connect to

the optical digital input jack of this unit with an optical cable.

To connect a game console or tuner to TV, you need extra video pin

cables (optional).

3) y 4) y

16 En

Initial settings

Selecting language for menu

display

Turn the unit and your TV on.

Switch TV’s input to “VIDEO INPUT 1

(example)”.

Check whether the initial screen is displayed.

Press and hold SETUP key until the

“LANGUAGE SETUP” menu appears on

your TV.

Press U / V key to select the desired

language and then press ENTER key.

Selectable item: ENGLISH, DEUTSCH, FRANÇAIS,

ESPAÑOL, ITALIANO, NEDERLANDS, РУССКИЙ,

SVENSKA

Initial setting: English

YSP-2200

Push [SETUP] to

begin SETUP MENU.

(example)

[ ]/[ ]:Sel [ENTER]:Return

3)LANGUAGE SETUP

When the screen is not displayed

Confirm the case followings.

– The input jack of your TV and the video output jack of the unit are

connected.

– The input of your TV is set to “VIDEO INPUT 1 (example)”.

1) y

17 En

Initial settings

PREPARATION

CONNECTION/

INITIAL SETTINGS PLAYBACK SETTINGS

TROUBLESHOOTING

APPENDIX

This unit creates a sound field by reflecting sound beams on the

walls of your listening room and by broadening the cohesion of

all the channels. Just as you would arrange the speaker position of

other audio systems, you need to set the beam angle to enjoy the

best possible sound from this unit.

This unit employs the beam optimization and sound optimization

features with the aid of the supplied IntelliBeam microphone, allowing

you to avoid troublesome listening-based setup and achieving highly

accurate sound adjustments that best match your listening

environment. We call these two features “IntelliBeam” generically.

Beam optimization:

This feature optimizes the beam angle so that the parameter best

matches your listening environment.

Sound optimization:

This feature optimizes the beam delay, volume, and quality so

that the parameters best match your listening environment.

This unit performs these two automatic optimizations with the aid

of the supplied IntelliBeam microphone.

Auto setup for appropriate

surround effects (IntelliBeam)

Installing the IntelliBeam microphone

Place the IntelliBeam microphone on a flat

level surface at your normal listening position.

Use the supplied cardboard microphone stand or a tripod

to place the IntelliBeam microphone at the same height as

your ears would be when you are seated.

■ Assembling the supplied cardboard

microphone stand

• The AUTO SETUP procedure may not be run successfully if this

unit is installed in one of the rooms described in “Installing this

unit” on page 11. In such cases, run MANUAL SETUP (☞p. 20)

to manually adjust the corresponding parameters.

• Do not connect the IntelliBeam microphone to an extension cable

as doing so may result in an inaccurate sound optimization.

• After you have completed the AUTO SETUP procedure, be sure

to disconnect the IntelliBeam microphone.

• The IntelliBeam microphone is sensitive to heat.

– Keep the IntelliBeam microphone away from direct sunlight.

– Do not place the IntelliBeam microphone on top of this unit.

Notes

1 2 3

Remove

Fit in

Run

through

Place

horizontally

Fit in

Make sure that there are no obstacles between the

IntelliBeam microphone and the walls in your listening

room as these objects obstruct the path of sound beams.

However, any objects that are in contact with the walls

will be regarded as a protruding part of the walls.

Check if a video pin cable is connected.

IntelliBeam microphone Upper limit

Within 1 m (3.3 ft)

Center height of this

unit

Cardboard microphone

stand

Within 1 m (3.3 ft)

Listening

position

1.8 m (6.0 ft)

or more

Lower limit

Center line

IntelliBeam

microphone

Cardboard microphone stand

• “BEAM+SOUND OPTIMIZE” screen appears automatically when

the IntelliBeam microphone is connected. “BEAM OPTIMIZE

ONLY” or “SOUND OPTIMIZE ONLY” can be selected separately

in setup menu (☞p. 20).

• Data set automatically can be saved in the system memory (☞p. 22).

You can save the several data depending on listening room and you

can change the setting conveniently.

2) y

Initial settings

18 En

Using AUTO SETUP (IntelliBeam)

Turn the unit and your TV on.

Switch TV’s input to “VIDEO INPUT 1

(example)”.

Connect the supplied IntelliBeam

microphone to the INTELLIBEAM jack.

• It is normal for loud test tones to be output during the AUTO

SETUP procedure. Make sure that there are no children around

in the listening room while the AUTO SETUP procedure is in

progress.

• Make sure that your listening room is as quiet as possible. For

accurate measurement, turn off air conditioner or other devices

that make noises.

• If there are curtains in your listening room, we recommend

following the procedure below.

1 Open the curtains to improve sound reflection.

2 Run “BEAM OPTIMIZE ONLY”.

3 Close the curtains.

4 Run “SOUND OPTIMIZE ONLY”.

Notes

IntelliBeam microphone

When pressing RETURN key displays the setup menu

Press SETUP key repeatedly and display the menu screen again, then

select: “AUTO SETUP”  “BEAM+SOUND OPTIMIZE”.

When the screen is not displayed

Confirm the case below.

– The input jack of your TV and the video output jack of the unit are

connected.

– The input of your TV is set to “VIDEO INPUT 1 (example)”.

“BEAM+SOUND OPTIMIZE” is selected automatically. When you

perform “BEAM OPTIMIZE ONLY” or “SOUND OPTIMIZE ONLY”

only, refer to “AUTO SETUP via setup menu (☞p. 20)”.

• Wait outside the room during the AUTO SETUP procedure.

• The AUTO SETUP procedure takes about 3 minutes.

• To cancel the AUTO SETUP procedure after it is started, press

RETURN key.

1) y 2) y

3) y

La page charge ...

Yamaha YSP-2200 Manuel utilisateur

Marque: Yamaha

Modèle: YSP-2200

Catégorie: Destinataire

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

italiano: Yamaha YSP-2200 Manuale utente
English: Yamaha YSP-2200 User manual
español: Yamaha YSP-2200 Manual de usuario
Deutsch: Yamaha YSP-2200 Benutzerhandbuch
русский: Yamaha YSP-2200 Руководство пользователя
Nederlands: Yamaha YSP-2200 Handleiding
dansk: Yamaha YSP-2200 Brugermanual
svenska: Yamaha YSP-2200 Användarmanual
Türkçe: Yamaha YSP-2200 Kullanım kılavuzu
română: Yamaha YSP-2200 Manual de utilizare

Yamaha YSP-2200 Manuel utilisateur

Yamaha YSP-2200 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents