Hobart HS7N-2R Slicer Instructions Manual

Marque: Hobart

Modèle: HS7N-2R Slicer

Taper: Instructions Manual

701 S. RIDGE AVENUE

TROY, OHIO 45374-0001

937 332-3000

www.hobartcorp.com FORM 48175 (August 2023)

MODEL HS7N-2R SLICER

– 2 –

TABLE OF CONTENTS

GENERAL ............................................................................................................................................. 3

Features .......................................................................................................................................... 3

Accessories and Options ................................................................................................................. 4

INSTALLATION .................................................................................................................................... 4

Unpacking ........................................................................................................................................ 4

Electrical Connections ..................................................................................................................... 4

Location ........................................................................................................................................... 4

Assembly ......................................................................................................................................... 5

Clean Before Using ......................................................................................................................... 5

OPERATION ........................................................................................................................................ 6

Slicing In Manual Mode ................................................................................................................... 6

Slicing In Automatic ......................................................................................................................... 7

CLEANING ........................................................................................................................................... 8

Cleaning Surface and Parts ............................................................................................................. 8

Disassembly for Cleaning ................................................................................................................ 8

Sharpener .................................................................................................................................. 8

Meat Grip ................................................................................................................................... 9

Product Tray .............................................................................................................................. 9

Top Knife Cover and Ring Guard Cover .................................................................................. 10

Cleaning ........................................................................................................................................ 10

Sharpener ................................................................................................................................ 10

Meat Grip ................................................................................................................................. 10

Product Tray ............................................................................................................................ 10

Top Knife Cover and Ring Guard ............................................................................................. 10

Knife ........................................................................................................................................ 10

Under the Slice ....................................................................................................................... 10

Reassembly After Cleaning ............................................................................................................11

Ring Guard Cover and Top Knife Cover ...................................................................................11

Product Tray .............................................................................................................................11

Meat Grip ................................................................................................................................. 12

Sharpener ................................................................................................................................ 12

Gasket Inspection .......................................................................................................................... 13

MAINTENANCE ................................................................................................................................. 14

Knife Sharpening ........................................................................................................................... 14

Lubrication — Carriage Slide Rod ................................................................................................. 15

Lubrication — Meat Grip Slide Rod ............................................................................................... 15

Service ........................................................................................................................................... 15

– 3 –

Installation, Operation and Care of

MODEL HS7N-2R Slicer

SAVE THESE INSTRUCTIONS

GENERAL

The HS7N-2R Slicer is equipped with a 1/2 hp motor and is available for single-phase electrical service.

The slicer features 13" diameter carbon steel knife. The slicer is furnished with a cord and plug as standard

equipment.

FEATURES

• No Volt Release – requires the slicer to be restarted after a power interruption.

• Gauge Plate Interlock – prevents the Product Tray (Fig. 1) from being tilted or removed unless the

Product Tray is in the home position (pulled all the way forward) and the Gauge Plate is closed.

• Home Start – requires the Product Tray (Fig. 1) to be in the home position (pulled all the way

forward) before the slicer can be started.

• Close-to-Stop–turnstheslicerowhentheGaugePlateisreturnedtotheclosedpositionby

turningtheIndexKnob(Fig.1)fullyclockwise.ThesliceralsoisturnedoiftheOFFbuttonis

pressed.

• Auto-Shuto–willautomaticallyturnthesliceroifaback-and-forthstrokeoftheProductTray

has not been made within 30 seconds.

The HS7N-2R Slicer features automatic slicing with a choice of four speeds for the Product Tray. The

Select-a-StrokeTMfeatureallowstheusertoselecttheexactstrokelengthtottheproductbeingsliced.

This can increase the slice rate on items needing a shorter stroke.

Fig. 1

– 4 –

ACCESSORIES AND OPTIONS

• Fences – The fence clamps on the Product Tray to limit product movement during slicing.

• Food Chute – Clamps on the Product Tray to limit movement of product during slicing (for tomatoes,

onions or similar items).

• Deector–Assistsindeectingslicedproducttotheplatterduringslicing.TheDeectortson

theDeectorBracketlocatedontheSharpenerMount.

INSTALLATION

UNPACKING

The slicer was inspected before leaving the factory. The carrier assumes full responsibility for safe delivery

upon acceptance of the shipment. Check for possible shipping damage immediately after receipt.

If the slicer is found to be damaged, complete the following steps:

 1.Carriermustbenotiedwithinvebusinessdaysofreceipt.

 2.Carrier’slocalterminalmustbenotiedimmediatelyupondiscovery(notethetime,date,andwho

wasspokento),andfollowupandconrmwithwrittenorelectroniccommunication.

3. All original packing materials must be kept for inspection purposes.

 4.Theslicercannothavebeenmoved,installed,ormodied.

5. Notify Hobart customer care at (800) 333-7447.

Priortoinstallingtheslicer,testtheelectricalservicetoensureitagreeswiththespecicationsonthe

machine data plate. The data plate is located on the left side of the slicer base.

ELECTRICAL CONNECTIONS

The electrical cord on this machine is equipped with a three-pronged grounding

plug which must be connected to a properly grounded receptacle. If the receptacle is not the

proper grounding type, contact an electrician. Do not remove the grounding prong from the plug.

LOCATION

Place the slicer on a suitable counter or tabletop. Allow enough space around the slicer so the carriage

can move freely forward and back.

– 5 –

ASSEMBLY

The Product Tray (Fig. 1) must be installed.

To install the Product Tray on the slicer, lower the bottom of the Support Arm onto the Carriage Hinge Pins

(Fig. 2). Tilt the Product Tray toward the Gauge Plate. Turn the Knob on the Support Arm until it is tight

against the Support Arm.

CLEAN BEFORE USING

The slicer must be thoroughly cleaned and sanitized after installation and before being used. See Cleaning.

Fig. 2

– 6 –

OPERATION

Rotating knife. Use meat grip. Unplug machine power cord before cleaning, servicing

or removing parts. Replace parts before use.

SLICING IN MANUAL MODE

• Close the Gauge Plate (Fig. 1) by turning the

Index Knob (Fig. 1) fully clockwise.

• Ensure Lever (Fig. 3) is in the down position for

manual mode.

• Pull the Product Tray (Fig. 1) toward the operator

until it reaches its stop. This is the home position.

• Raise the Meat Grip (Fig. 1) to the top of the

Product Tray to rest in the Meat Grip Slot.

• Place the product to be sliced against the Gauge

Plate (Fig. 1) on the Product Tray (Fig. 1).

• Set the Meat Grip against the product, or use the Fence or Food Chute if desired. Refer to

Accessories & Options on page 4.

• Turn the slicer on by pressing the KNIFE ON button (Fig. 4).

• Adjust the Gauge Plate to obtain the desired slice thickness by turning the Index Knob

counterclockwise. The numbers on the Index Knob do not indicate actual measurements but may

be used for reference to duplicate slice thickness.

• Use the Product Tray Handle (Fig. 1) to push

and pull the Product Tray back and forth to

slice. When nished, pull the Product Tray

forward until it stops. Turn the Index Knob fully

clockwise to close the Gauge Plate. This will

turntheslicero.TheOFFButton(Fig.4)can

also be pressed to stop the slicer.

• Raise the Meat Grip to the top of the Product

Tray to rest in the Meat Grip Slot.

Fig. 3

Fig. 4

– 7 –

SLICING IN AUTOMATIC

• Close the Gauge Plate (Fig. 1) by turning the Index Knob (Fig. 1) fully clockwise.

• Ensure Lever (Fig. 3) is in the down position for manual mode.

• Pull the Product Tray (Fig. 1) toward the operator until it reaches its stop. This is the home position.

• Raise the Meat Grip (Fig. 1) to the top of the Product Tray to rest in the Meat Grip Slot.

• Place the product to be sliced against the Gauge Plate (Fig. 1) on the Product Tray (Fig. 1).

• Set the Meat Grip against the product, or use

the Fence or Food Chute if desired. Refer to

Accessories & Options on page 4.

• Lift the Lever (Fig. 5) to the up position for

automatic mode.

• Select one of the four speeds for the Product

Tray to move back and forth. Press the

Rabbit symbol (Fig. 4) to increase speed; press the

Turtle symbol (Fig. 4) to decrease speed. The speed indicator, located to the right of the symbols,

shows which speed is selected. The speed can be changed at any time.

• Select a stroke length for the Product Tray to move back and forth. Press the STROKE LENGTH

button (Fig. 4) to toggle through the lengths. The indicator above the button shows the length.

More lights equal a longer stroke. The stroke length can be changed at any time.

• Turn the slicer on by pressing the KNIFE ON button (Fig. 4).

• Adjust the Gauge Plate to obtain the desired slice thickness by turning the Index Knob

counterclockwise. The numbers on the Index Knob do not indicate actual measurements but may

be used for reference to duplicate slice thickness.

• Whennished,turntheIndexKnobfullyclockwisetoclosetheGaugePlateorpresstheKNIFE

ON button (Fig. 4) to stop the slicer. This will stop the slicer and return the Product Tray to the

home position.

NOTE: The OFF button can be pressed to stop the slicer. The Product Tray will stop moving immediately.

Lower the Lever (Fig. 3) and pull the Product Tray toward the operator to the home position.

• Raise the Meat Grip to the top of the Product Tray to rest in the Meat Grip Slot.

Fig. 5

– 8 –

CLEANING

Unplug the machine power cord and turn the index knob fully clockwise to close

the gauge plate before cleaning the slicer.

The slicer knife is very sharp. Exercise extreme caution when working near the knife.

This machine must be thoroughly cleaned and sanitized at least as often as required by local regulation

or after being idle for an extended period of time.

NOTE: Sanitizer concentration shall comply with Section 4-501.114, Manual and Mechanical Warewashing

Equipment, Chemical Sanitization – Temperature, pH, Concentration, and Hardness of the FDA Food Code.

If a chemical sanitizer other than chlorine, iodine, or quaternary ammonium is used, it shall be applied in

accordance with the EPA-registered label use instructions.

For general cleaning, use a clean cloth soaked in mild detergent and warm water, and wipe all surfaces

of the machine especially where food or liquids can accumulate. Be sure to wipe any surface where there

is frequent hand contact including handles, knobs, and the control pad. Use generous amounts of soapy

water and sanitizer on the Sharpener Mount hardware. Rinse using a fresh cloth and clean water. Apply

sanitizing solution to clean surfaces. Make sure the slicer is clean of all food soil before sanitizing. Use only

products formulated to be safe on stainless steel or aluminum. DO NOT exceed chemical manufacturer’s

recommended concentrations for detergent or sanitizer.

CLEANING SURFACE AND PARTS

Frequency – The slicer shall be cleaned and sanitized at intervals to comply with national, state, and/or

local health codes.

DISASSEMBLY FOR CLEANING

In order to clean the slicer thoroughly, it is necessary to disassemble the slicer. It is recommended that all

parts be removed, cleaned, sanitized, and allowed to dry before re-assembling for use.

Sharpener

• The Sharpener (Fig. 6) is mounted on top of the slicer.

• Remove the Sharpener by lifting straight up.

Fig. 6

– 9 –

Meat Grip

• The Meat Grip (Fig. 7) is mounted on the Product Tray and can be removed for ease of cleaning.

• Remove the Meat Grip by loosening the Meat Grip Slide Rod from the Product Tray while holding

the Meat Grip Handle.

• Pull the Meat Grip Slide Rod from the Meat Grip Handle and Product Tray.

• Loosen the Meat Grip Handle (Fig. 8) and remove the Handle, Meat Grip Arm, and Washer from

the Meat Grip.

Product Tray

• To clean the Product Tray, make sure the Gauge Plate is closed.

• Pull the Product Tray toward the operator until it stops.

• Loosen the Knob (Fig. 9) on the Support Arm. Tilt the Product Tray to the right (Fig. 9).

• The Product Tray can be cleaned in this open position, or it can be removed by grasping with both

hands and lifting straight up.

Fig. 7 Fig. 8

MEAT GRIP

MEAT GRIP ARM

MEAT GRIP HANDLE

WASHER

Fig. 9

– 10 –

Top Knife Cover and Ring Guard Cover

• Remove the Top Knife Cover (Fig. 10) by pulling

on the Latch Knob. The Top Knife Cover is held

in place by a magnet under the Latch Knob.

• Remove the plastic Ring Guard Cover

(Fig. 10) by lifting up.

CLEANING

Sharpener

• Wipe out any residue remaining inside the Sharpener housing.

• Wash, rinse, and sanitize the Sharpener in a sink or dishwasher.

Meat Grip

• The Meat Grip can be washed, rinsed, and sanitized in a sink.

Product Tray

• The Product Tray can be washed, rinsed, and sanitized in a sink.

• Clean the Product Tray pin with the brush as shown (Fig. 11).

Top Knife Cover and Ring Guard

• Wash, rinse, and sanitize the Top Knife Cover and the plastic Ring Guard Cover in a sink or

dishwasher.

Knife

The slicer knife is very sharp.

Exercise extreme caution when working near the

knife.

• Clean completely around the Ring Guard

by working a moistened, folded paper towel

between the Ring Guard and the Knife

(Fig. 12).

• Wash, rinse, and sanitize both sides of the

Knife by wiping outward from the center. Never

clean any part of the slicer with steel pads.

Under the Slice

The HS7N-2R Slicer is equipped with Gas Assist Spring

(Fig. 13) to assist in cleaning under the slicer. To raise the

slicer, place hands under the front of the base and lift up

until it stops. The spring will hold the slicer in position for

cleaning. Push down base of the slicer to lower the slicer.

NOTE: Do not lift or lower the slicer with the control

panel.

Fig. 10

Fig. 11

Fig. 12

Fig. 13

– 11 –

REASSEMBLY AFTER CLEANING

After all components have been cleaned, sanitized, and allowed to dry, the slicer can be reassembled for

use.

Ring Guard Cover and Top Knife Cover

• Install the Ring Guard Cover on the three Guide Pins (Fig. 14).

• Position the Top Knife Cover (Fig. 15) on the lower two Guide Pins and lower the Latch Knob until

the magnet secures the Top Knife Cover in place.

Product Tray

• Lower the bottom of the Support Arm onto the Carriage Hinge Pins (Fig. 16).

• Tilt the Product Tray toward the Gauge Plate.

• Turn the Knob on the Support Arm until it is tight against the Support Arm.

Fig. 14 Fig. 15

Fig. 16

– 12 –

Meat Grip

• Assemble the Meat Grip Assembly (Fig. 17) by placing the Washer, Meat Grip Arm, and Meat Grip

Handle on the shaft of the Meat Grip.

• Tighten the Handle.

• Install the Meat Grip Assembly (Fig. 18) on the Product Tray by sliding the Meat Grip Slide Rod

into the Meat Grip Handle and Product Tray.

• Tighten the Meat Grip Slide Rod into the Product Tray.

• Lubricate the Meat Grip Slide Rod. See Maintenance.

Sharpener

• Install the Sharpener by lowering it back onto

the Sharpener Mount so the Rod and Pin on

thebottomoftheSharpenerttheSlotinthe

Sharpener Mount (Fig. 19).

• To use the Sharpener, see Maintenance.

Fig. 17 Fig. 18

MEAT GRIP

MEAT GRIP ARM

MEAT GRIP HANDLE

WASHER

Fig. 19

– 13 –

GASKET INSPECTION

Hobart recommends the manufacturer or an authorized service agent conduct inspections on the entire

slicer a minimum of every 6 months.

The slicer must be removed from service until repaired by the manufacturer or an

authorized service agent if any gasket or seal is found to be damaged or missing.

Fig. 20

– 14 –

MAINTENANCE

Unplug the machine power cord and turn the index knob fully clockwise to close

the gauge plate before doing any maintenance on the slicer.

KNIFE SHARPENING

Sharpen only when necessary. Prolonged or sharpening too frequently results in unnecessary

Knife wear.

Remove the Top Knife Cover by pulling on the Latch

Knob. The Top Knife Cover is held in place with a

strong magnet under the Latch Knob. Remove the

plastic Ring Guard Cover (Fig. 21) by lifting up.

Clean and sanitize the slicer as outlined in the cleaning

section before sharpening the knife. Food debris must

not be allowed to transfer from the Knife to the

Sharpener. Plug in the machine power cord.

Press and hold the KNIFE ON button for 15 seconds

(Fig. 22) while pulling the Sharpener Lever fully

forward (Fig. 22). After 15 seconds, release the

Sharpener Lever and press the OFF button. Unplug

the machine power cord. Clean and sanitize the slicer

as outlined in the cleaning section after sharpening

the knife. Install the plastic Ring Guard Cover and the

Top Knife Cover (Fig. 21).

Fig. 21

Fig. 22

– 15 –

LUBRICATION — CARRIAGE SLIDE ROD

Lubricate the Carriage Slide Rod with Lubriplate FMO-

200-AW oil (supplied). Once monthly, apply 4 - 5 drops

directly onto the Carriage Slide Rod on each side of

the Carriage Transport (Fig. 23).

To apply oil, pull out the telescoping tube on the oil

bottle, aim the tube, and squeeze gently on the sides

of the bottle. After applying oil, move the Carriage Tray

back and forth a few times so the oil spreads over the

entire length of the slide rod.

LUBRICATION — MEAT GRIP SLIDE ROD

The Meat Grip Slide Rod can be lubricated periodically

or when any resistance is felt while using the Meat

Grip assembly (Fig. 24). First, wipe the Meat Grip

Slide Rod so the lubrication is applied to a clean, dry

surface. Next, gently squeeze a small amount of the

provided Lubriplate oil on the rod. Then slide the Meat

Grip up and down the rod to restore smooth operation.

SERVICE

ContactyourlocalHobart-authorizedserviceoceforanyrepairsoradjustmentsneededontheslicer.

Fig. 23

Fig. 24

– 16 –

FORM 48175 (August 2023) PRINTED IN U.S.A.

701 S. RIDGE AVENUE

TROY, OHIO 45374-0001

937 332-3000

www.hobartcorp.com FORMULARIO 48175 (agosto de 2023)

CORTADORA MODELO HS7N-2R

– 2 –

TABLA DE CONTENIDO

GENERAL ............................................................................................................................................. 3

Características ................................................................................................................................. 3

Accesorios y opciones ..................................................................................................................... 4

INSTALACIÓN ..................................................................................................................................... 4

Desembalaje .................................................................................................................................... 4

Conexiones eléctricas ..................................................................................................................... 4

Ubicación ......................................................................................................................................... 4

Montaje ............................................................................................................................................ 5

Limpiar antes de usar ...................................................................................................................... 5

FUNCIONAMIENTO ............................................................................................................................ 6

Cortado en modo manual ................................................................................................................ 6

Corte en automático ........................................................................................................................ 7

LIMPIEZA ............................................................................................................................................. 8

Limpieza de la supercie y las piezas ............................................................................................. 8

Desmontaje para limpieza ............................................................................................................... 8

Alador ....................................................................................................................................... 8

Prensaambre ........................................................................................................................... 9

Bandeja de producto .................................................................................................................. 9

Cubierta de la cuchilla superior y cubierta del aro protector.................................................... 10

Limpieza ........................................................................................................................................ 10

Alador ..................................................................................................................................... 10

Prensaambre ......................................................................................................................... 10

Bandeja de producto ................................................................................................................ 10

Cubierta superior de la cuchilla y aro protector ....................................................................... 10

Cuchilla ................................................................................................................................... 10

Bajo la cortadora ..................................................................................................................... 10

Montaje tras la limpieza ..................................................................................................................11

Cubierta del aro protector y cubierta superior de la cuchilla.....................................................11

Bandeja de producto .................................................................................................................11

Prensaambre ......................................................................................................................... 12

Alador ..................................................................................................................................... 12

Inspección de las juntas ................................................................................................................ 13

MANTENIMIENTO ............................................................................................................................. 14

Alado de la cuchilla ...................................................................................................................... 14

Lubricación — Varilla deslizante del carro ..................................................................................... 15

Lubricación — Varilla deslizante del prensaambre ...................................................................... 15

Servicio .......................................................................................................................................... 15

– 3 –

Instalación, funcionamiento y cuidados de la cortadora

MODELO HS7N-2R

CONSERVE ESTAS INSTRUCCIONES

GENERAL

La cortadora HS7N-2R se ha equipado con un motor de 1/2 CV y está disponible para servicio eléctrico monofásico.

La cortadora cuenta con una cuchilla de acero al carbono de 13 pulg. de diámetro. La cortadora se suministra con

un cable y un enchufe como equipamiento estándar.

CARACTERÍSTICAS

• Sin liberación de tensión: requiere que la cortadora se reinicie después de una interrupción de energía.

• Enclavamiento del plato medidor: impide que la bandeja de producto (Fig. 1) se incline o se retire a menos

que la bandeja de producto se encuentre en la posición inicial (empujada completamente hacia delante) y

el plato medidor esté cerrado.

• Inicio: requiere que la bandeja de producto (Fig. 1) esté en la posición inicial (empujada completamente

hacia delante) antes de que la cortadora pueda ponerse en marcha.

• Cerrar-para-parar: apaga la cortadora cuando el plato medidor vuelve a la posición cerrada girando la perilla

de ajuste (Fig. 1) completamente en sentido horario. La cortadora también se apaga si se pulsa el botón

OFF.

• Apagado automático: apagará automáticamente la cortadora si no se ha realizado un movimiento de vaivén

de la bandeja de producto en 30 segundos.

La cortadora HS7N-2R ofrece un corte automático con cuatro velocidades que elegir para la bandeja de producto. La

función Select-a-StrokeTM permite al usuario seleccionar la longitud de carrera exacta para adaptarse al producto que

se va a cortar. Esto puede aumentar la velocidad de corte en los productos que necesitan una longitud más corta.

Fig. 1

CONTROLES

AFILADOR

PRENSAFIAMBRE

PLATO MEDIDOR

ASA DE LA BANDEJA

DE PRODUCTO

BANDEJA DE PRODUCTO

PERILLA

PERILLA DE AJUSTE

PALANCA

BRAZO DE SOPORTE

– 4 –

ACCESORIOS Y OPCIONES

• Cercos: el cerco se ja a la bandeja de producto para limitar el movimiento del producto durante el corte.

• Conducto para alimentos: se ja a la bandeja de producto para limitar el movimiento del producto durante

el corte (para tomates, cebollas o alimentos similares).

• Deector: ayuda a desviar el producto cortado hacia la bandeja durante el corte. El deector encaja en el

soporte del deector situado en el soporte del alador.

INSTALACIÓN

DESEMBALAJE

La cortadora fue inspeccionada antes de salir de fábrica. El transportista asume total responsabilidad por la entrega

segura una vez aceptado el cargamento. Compruebe que no haya daños al cargamento inmediatamente después

de recibirlo.

Si la cortadora está dañada, siga estos pasos:

1. Noticar al transportista dentro de los cinco días hábiles siguientes a la fecha de recepción.

2. Noticar de inmediato a la terminal local del transportista tras el descubrimiento (anotar la hora, la fecha y

la persona con quien se habló) y hacer un seguimiento y conrmación mediante comunicaciones escritas o

electrónicas.

3. Conservar todos los materiales originales del embalaje por motivos de inspección.

4. La cortadora no debe moverse, instalarse ni modicarse.

5. Noticar al Servicio de Atención al Cliente de Hobart al (800) 333-7447.

Antes de instalar la cortadora, pruebe el servicio eléctrico para asegurarse de que concuerda con las especicaciones

de la placa de datos del equipo. La placa de datos está ubicada del lado izquierdo de la base de la cortadora.

CONEXIONES ELÉCTRICAS

ADVERTENCIA

El cable eléctrico de esta máquina está equipado con un enchufe de conexión a tierra con tres

terminales que se deben conectar correctamente a una toma con conexión a tierra. Si la toma de corriente

no es la correcta, comuníquese con un electricista. No quite el terminal de conexión a tierra del enchufe.

UBICACIÓN

Coloque la cortadora sobre un mostrador o una mesa adecuada. Deje espacio suciente alrededor de la cortadora

para que el carro pueda moverse libremente hacia delante y hacia atrás.

La page charge ...

Hobart HS7N-2R Slicer Instructions Manual

Marque: Hobart

Modèle: HS7N-2R Slicer

Taper: Instructions Manual

Télécharger le PDF

rapport

dans d''autres langues

English: Hobart HS7N-2R Slicer
español: Hobart HS7N-2R Slicer

Hobart HS7N-2R Slicer Instructions Manual

Hobart HS7N-2R Slicer Instructions Manual

dans d''autres langues

Documents connexes

Autres documents