Hobart HS Series Instructions Manual

Taper
Instructions Manual
701 S. RIDGE AVENUE
TROY, OHIO 45374-0001
937 332-3000
www.hobartcorp.com FORM 35284 Rev. F (August 2021))
MODEL HS SERIES SLICERS
MODEL
Manual Slicers
HS6
HS6N
HS6 (Canada)
HS6N (Canada)
HS8
HS8N
HS8 (Canada)
HS8N (Canada)
Automatic Slicers
HS7
HS7N
HS7 (Canada)
HS7N (Canada)
HS7 (Japan)
HS7N (Japan)
HS9
HS9N
HS9 (Canada)
HS9N (Canada)
– 2 –
© HOBART, 2019
TABLE OF CONTENTS
GENERAL ............................................................................................................................................. 3
Features .......................................................................................................................................... 4
Accessories and Options ................................................................................................................. 4
INSTALLATION .................................................................................................................................... 5
Unpacking ........................................................................................................................................ 5
Electrical Connections ..................................................................................................................... 5
Location ........................................................................................................................................... 5
Assembly ......................................................................................................................................... 6
Clean Before Using ......................................................................................................................... 6
OPERATION ........................................................................................................................................ 7
Slicing In Manual Mode (HS6 and HS8 Series) ............................................................................... 7
Slicing In Manual Mode (HS7 and HS9 Series) ............................................................................... 7
Slicing In Automatic Mode (HS7 and HS9 Series) ........................................................................... 8
CLEANING ........................................................................................................................................... 9
Cleaning Surface and Parts ............................................................................................................. 9
Disassembly for Cleaning ................................................................................................................ 9
Sharpener .................................................................................................................................. 9
Meat Grip ................................................................................................................................. 10
Product Tray ............................................................................................................................ 10
Top Knife Cover and Ring Guard Cover ...................................................................................11
Knife (Removable – HS6, HS7, HS8, and HS9) .......................................................................11
Cleaning ........................................................................................................................................ 12
Sharpener ................................................................................................................................ 12
Meat Grip ................................................................................................................................. 12
Product Tray ............................................................................................................................ 12
Top Knife Cover and Ring Guard ............................................................................................. 12
Knife (Removable) ................................................................................................................... 12
Knife (Non-Removable) ........................................................................................................... 12
Under the Slice ........................................................................................................................ 12
Reassembly After Cleaning ........................................................................................................... 13
Knife (Removable with Knife Removal Tool) ............................................................................ 13
Ring Guard Cover and Top Knife Cover .................................................................................. 14
Product Tray ............................................................................................................................ 14
Meat Grip ................................................................................................................................. 15
Sharpener ................................................................................................................................ 15
Gasket Inspection .......................................................................................................................... 16
MAINTENANCE ................................................................................................................................. 17
Knife Sharpening ........................................................................................................................... 17
Lubrication — Carriage Slide Rod ................................................................................................. 18
Lubrication — Meat Grip Slide Rod ............................................................................................... 18
Service ........................................................................................................................................... 18
– 3 –
Installation, Operation and Care of
MODEL HS Series Slicers
SAVE THESE INSTRUCTIONS
GENERAL
The HS Series Slicers are equipped with a 1/2 hp motor and are available for single-phase electrical
service. The slicer features the Hobart CleanCutTM 13" diameter contoured stainless steel knife. The slicer
is furnished with a cord and plug as standard equipment.
Fig. 1
Automatic Models
Manual Models
– 4 –
FEATURES
No Volt Release – requires the slicer to be restarted after a power interruption.
Gauge Plate Interlock – prevents the Product Tray (Fig. 1) from being tilted or removed unless the
Product Tray is in the home position (pulled all the way forward) and the Gauge Plate is closed.
Home Start – requires the Product Tray (Fig. 1) to be in the home position (pulled all the way
forward) before the slicer can be started.
• Close-to-Stop–turnstheslicerowhentheGaugePlateisreturnedtotheclosedpositionby
turningtheIndexKnob(Fig.1)fullyclockwise.ThesliceralsoisturnedoiftheOFFbuttonis
pressed.
• Auto-Shuto–willautomaticallyturnthesliceroifaback-and-forthstrokeoftheProductTray
has not been made within 30 seconds.
The HS7 and HS9 Series Slicers feature automatic slicing with a choice of four speeds for the Product
Tray. The Select-a-StrokeTMfeatureallowstheusertoselecttheexactstrokelengthtottheproductbeing
sliced. This can increase the slice rate on items needing a shorter stroke.
MODEL NO VOLT
RELEASE
GAUGE
PLATE
INTERLOCK
HOME
START
CLOSE TO
STOP
AUTO
SHUTOFF
REMOVABLE
KNIFE
HS6 Yes No No No No Yes
HS6N Yes No No No No No
HS7 Yes No Yes No No Yes
HS7N Yes No Yes No No No
HS8 Yes Yes Yes Yes Yes Yes
HS8N Yes Yes Yes Yes Yes No
HS9 Yes Yes Yes Yes Yes Yes
HS9N Yes Yes Yes Yes Yes No
ACCESSORIES AND OPTIONS
Fences – The fence clamps on the Product Tray to limit product movement during slicing.
Food Chute – Clamps on the Product Tray to limit movement of product during slicing (for tomatoes,
onions or similar items).
• Deector–Assistsindeectingslicedproducttotheplatterduringslicing.TheDeectortson
theDeectorBracketlocatedontheSharpenerMount.
– 5 –
INSTALLATION
UNPACKING
The slicer was inspected before leaving the factory. The carrier assumes full responsibility for safe delivery
upon acceptance of the shipment. Check for possible shipping damage immediately after receipt.
If the slicer is found to be damaged, complete the following steps:
1. Carriermustbenotiedwithinvebusinessdaysofreceipt.
2. Carrier’slocalterminalmustbenotiedimmediatelyupondiscovery(notethetime,date,andwho
wasspokento),andfollowupandconrmwithwrittenorelectroniccommunication.
3. All original packing materials must be kept for inspection purposes.
4. Theslicercannothavebeenmoved,installed,ormodied.
5. Notify Hobart customer care at (800) 333-7447.
Priortoinstallingtheslicer,testtheelectricalservicetoensureitagreeswiththespecicationsonthe
machine data plate. The data plate is located on the left side of the slicer base.
ELECTRICAL CONNECTIONS
The electrical cord on this machine is equipped with a three-pronged grounding
plug which must be connected to a properly grounded receptacle. If the receptacle is not the
proper grounding type, contact an electrician. Do not remove the grounding prong from the plug.
LOCATION
Place the slicer on a suitable counter or tabletop. Allow enough space around the slicer so the carriage
can move freely forward and back.
– 6 –
ASSEMBLY
The Product Tray (Fig. 1) must be installed.
To install the Product Tray on the slicer, lower the bottom of the Support Arm onto the Carriage Hinge Pins
(Fig. 2). Tilt the Product Tray toward the Gauge Plate. Turn the Knob on the Support Arm until it is tight
against the Support Arm.
CLEAN BEFORE USING
The slicer must be thoroughly cleaned and sanitized after installation and before being used. See Cleaning.
Fig. 2
– 7 –
OPERATION
Rotating knife. Use meat grip. Unplug machine power cord before cleaning, servicing
or removing parts. Replace parts before use.
SLICING IN MANUAL MODE (HS6 AND HS8 SERIES)
Close the Gauge Plate (Fig. 1) by turning the
Index Knob (Fig. 1) fully clockwise.
Pull the Product Tray (Fig. 1) toward the
operator until it reaches its stop. This is the
home position.
Raise the Meat Grip (Fig. 1) to the top of the
Product Tray to rest in the Meat Grip Slot.
Place the product to be sliced against the
Gauge Plate (Fig. 1) on the Product Tray (Fig. 1).
Set the Meat Grip against the product, or use the Fence or Food Chute if desired. Refer to
Accessories & Options on page 4.
Turn the slicer on by pressing the KNIFE ON button (Fig. 3).
Adjust the Gauge Plate to obtain the desired slice thickness by turning the Index Knob
counterclockwise. The numbers on the Index Knob do not indicate actual measurements but may
be used for reference to duplicate slice thickness.
Use the Product Tray Handle (Fig. 1) to push and pull the Product Tray back and forth to slice.
Whennished,pulltheProductTrayforwarduntilitstops.TurntheIndexKnobfullyclockwiseto
closetheGaugePlate,thiswillturntheslicero.TheOFFButton(Fig.3)canalsobepressedto
stop the slicer.
Raise the Meat Grip to the top of the Product Tray to rest in the Meat Grip Slot.
SLICING IN MANUAL MODE (HS7 AND HS9 SERIES)
Close the Gauge Plate (Fig. 1) by turning the
Index Knob (Fig. 1) fully clockwise.
Ensure Lever (Fig. 4) is in the down position for
manual mode.
Pull the Product Tray (Fig. 1) toward the operator
until it reaches its stop. This is the home position.
Raise the Meat Grip (Fig. 1) to the top of the
Product Tray to rest in the Meat Grip Slot.
Place the product to be sliced against the Gauge
Plate (Fig. 1) on the Product Tray (Fig. 1).
Set the Meat Grip against the product, or use the Fence or Food Chute if desired. Refer to
Accessories & Options on page 4.
Fig. 3
Fig. 4
– 8 –
Turn the slicer on by pressing the KNIFE ON button (Fig. 5).
Adjust the Gauge Plate to obtain the desired slice thickness by turning the Index Knob
counterclockwise. The numbers on the Index Knob do not indicate actual measurements but may
be used for reference to duplicate slice thickness.
Use the Product Tray Handle (Fig. 1) to push
and pull the Product Tray back and forth to
slice. When nished, pull the Product Tray
forward until it stops. Turn the Index Knob fully
clockwise to close the Gauge Plate. This will
turntheslicero.TheOFFButton(Fig.5)can
also be pressed to stop the slicer.
Raise the Meat Grip to the top of the Product
Tray to rest in the Meat Grip Slot.
SLICING IN AUTOMATIC MODE (HS7 AND HS9 SERIES)
Close the Gauge Plate (Fig. 1) by turning the Index Knob (Fig. 1) fully clockwise.
Ensure Lever (Fig. 4) is in the down position for manual mode.
Pull the Product Tray (Fig. 1) toward the operator until it reaches its stop. This is the home position.
Raise the Meat Grip (Fig. 1) to the top of the Product Tray to rest in the Meat Grip Slot.
Place the product to be sliced against the Gauge Plate (Fig. 1) on the Product Tray (Fig. 1).
Set the Meat Grip against the product, or use
the Fence or Food Chute if desired. Refer to
Accessories & Options on page 4.
Lift the Lever (Fig. 6) to the up position for
automatic mode.
Select one of the four speeds for the Product
Tray to move back and forth. Press the
Rabbit symbol (Fig. 5) to increase speed; press the
Turtle symbol (Fig. 5) to decrease speed. The speed indicator, located to the right of the symbols,
shows which speed is selected. The speed can be changed at any time.
Select a stroke length for the Product Tray to move back and forth. Press the STROKE LENGTH
button (Fig. 5) to toggle through the lengths. The indicator above the button shows the length.
More lights equal a longer stroke. The stroke length can be changed at any time.
Turn the slicer on by pressing the KNIFE ON button (Fig. 5).
Adjust the Gauge Plate to obtain the desired slice thickness by turning the Index Knob
counterclockwise. The numbers on the Index Knob do not indicate actual measurements but may
be used for reference to duplicate slice thickness.
• Whennished,turntheIndexKnobfullyclockwisetoclosetheGaugePlateorpresstheKNIFE
ON button (Fig. 5) to stop the slicer. This will stop the slicer and return the Product Tray to the
home position.
NOTE: The OFF button can be pressed to stop the slicer. The Product Tray will stop moving immediately.
Lower the Lever (Fig. 4) and pull the Product Tray toward the operator to the home position.
Raise the Meat Grip to the top of the Product Tray to rest in the Meat Grip Slot.
Fig. 5
Fig. 6
– 9 –
CLEANING
Unplug the machine power cord and turn the index knob fully clockwise to close
the gauge plate before cleaning the slicer.
The slicer knife is very sharp. Exercise extreme caution when working near the knife.
This machine must be thoroughly cleaned and sanitized at least as often as required by local regulation
or after being idle for an extended period of time.
NOTE: Sanitizer concentration shall comply with Section 4-501.114, Manual and Mechanical Warewashing
Equipment, Chemical Sanitization – Temperature, pH, Concentration, and Hardness of the FDA Food Code.
If a chemical sanitizer other than chlorine, iodine, or quaternary ammonium is used, it shall be applied in
accordance with the EPA-registered label use instructions.
For general cleaning, use a clean cloth soaked in mild detergent and warm water, and wipe all surfaces
of the machine especially where food or liquids can accumulate. Be sure to wipe any surface where there
is frequent hand contact including handles, knobs, and the control pad. Use generous amounts of soapy
water and sanitizer on the Sharpener Mount hardware. Rinse using a fresh cloth and clean water. Apply
sanitizing solution to clean surfaces. Make sure the slicer is clean of all food soil before sanitizing. Use only
products formulated to be safe on stainless steel or aluminum. DO NOT exceed chemical manufacturer’s
recommended concentrations for detergent or sanitizer.
CLEANING SURFACE AND PARTS
Frequency – The slicer shall be cleaned and sanitized at intervals to comply with national, state, and/or
local health codes.
DISASSEMBLY FOR CLEANING
In order to clean the slicer thoroughly, it is necessary to disassemble the slicer. It is recommended that all
parts be removed, cleaned, sanitized, and allowed to dry before re-assembling for use.
Sharpener
The Sharpener (Fig. 7) is mounted on top of the slicer.
Remove the Sharpener by lifting straight up.
Fig. 7
– 10 –
Meat Grip
The Meat Grip (Fig. 8) is mounted on the Product Tray and can be removed for ease of cleaning.
Remove the Meat Grip by loosening the Meat Grip Slide Rod from the Product Tray while holding
the Meat Grip Handle.
Pull the Meat Grip Slide Rod from the Meat Grip Handle and Product Tray.
Loosen the Meat Grip Handle (Fig. 9) and remove the Handle, Meat Grip Arm, and Washer from
the Meat Grip.
Product Tray
To clean the Product Tray, make sure the Gauge Plate is closed.
Pull the Product Tray toward the operator until it stops.
Loosen the Knob (Fig. 10) on the Support Arm. Tilt the Product Tray to the right (Fig. 10).
The Product Tray can be cleaned in this open position, or it can be removed by grasping with both
hands and lifting straight up.
Fig. 8 Fig. 9
MEAT GRIP
MEAT GRIP ARM
MEAT GRIP HANDLE
WASHER
Fig. 10
– 11 –
Top Knife Cover and Ring Guard Cover
Remove the Top Knife Cover (Fig. 11) by pulling
on the Latch Knob. The Top Knife Cover is held
in place by a magnet under the Latch Knob.
Remove the plastic Ring Guard Cover
(Fig. 11) by lifting up.
Knife (Removable – HS6, HS7, HS8, and HS9)
The slicer knife is very sharp.
Exercise extreme caution when working
near the knife.
Ensure the gauge plate is closed, then rotate
the Knife by hand to align the arrow on the
Knife with the Pin on the Ring Guard at the
1 o'clock position (Fig. 12). The ridge on the
Knife Hub will also align with the same pin.
The Pin (Fig. 13) on the Knife Removal Tool
ts the hole in the Knife at the 11 o'clock
position (Fig. 13).
Place the Knife Removal Tool on the Knife
(Fig.14).ThethreeslotsontheTooltthe
three Pins on the Ring Guard (Fig. 14).
• PushtheHandlermly,allthewayintothe
hub. Then, turn the Handle counterclockwise
until it stops (Fig. 15). Some resistance may
be experienced when turning.
Lift Knife and Tool up and out (Fig. 15).
Fig. 11
Fig. 12
Fig. 13 Fig. 14
1:00
Fig. 15
T
U
R
N
C
C
W
PUSH FIRST
– 12 –
CLEANING
Sharpener
Wipe out any residue remaining inside the Sharpener housing.
Wash, rinse, and sanitize the Sharpener in a sink or dishwasher.
Meat Grip
The Meat Grip can be washed, rinsed, and sanitized in a sink.
Product Tray
The Product Tray can be washed, rinsed, and sanitized in a sink.
Clean the Product Tray pin with the brush as shown (Fig. 16).
Top Knife Cover and Ring Guard
Wash, rinse, and sanitize the Top Knife Cover and the plastic Ring Guard Cover in a sink or
dishwasher.
Knife (Removable)
NOTE: Always carry Knife Removal Tool and Knife by Tool Handle.
Wash, rinse, and sanitize the Knife and Knife Removal Tool in a sink or dishwasher.
Knife (Non-Removable)
The slicer knife is very sharp.
Exercise extreme caution when working near the
knife.
Clean completely around the Ring Guard
by working a moistened, folded paper towel
between the Ring Guard and the Knife
(Fig. 17).
Wash, rinse, and sanitize both sides of the
Knife by wiping outward from the center. Never
clean any part of the slicer with steel pads.
Under the Slice
The HS6 and HS8 Series Slicers are equipped with a Cleaning Leg (Fig. 18) to assist in cleaning under
the slicer. To engage the Cleaning Leg, lift the front of the slicer base. The Cleaning Leg will swing straight
down. Pull the Cleaning Leg all the way to the front so the slicer is completely supported before cleaning
underneath.
The HS7 and HS9 Series Slicers are equipped with Gas Assist Spring (Fig. 19) to assist in cleaning under
the slicer. To raise the slicer, place hands under the front of the base and lift up until it stops. The spring
will hold the slicer in position for cleaning. Push down base of the slicer to lower the slicer.
NOTE: Do not lift or lower the slicer with the control panel.
Fig. 16
Fig. 17
Fig. 18 Fig. 19
– 13 –
REASSEMBLY AFTER CLEANING
After all components have been cleaned, sanitized, and allowed to dry, the slicer can be reassembled for
use.
Knife (Removable with Knife Removal Tool)
Orient the Knife Hub mark to the arrow as
shown (Fig. 20), so it points to the Pin on the
Ring Guard at the 1 o'clock position (Fig. 20).
Place the Knife and Tool so the Pin on the
Knife Removal Tool is at the 11 o'clock position
(Fig. 21).
Place the Slots on the Knife Removal Tool
taroundthethreePinsontheRingGuard
(Fig. 21).
NOTE: If the Tool does not push the pins on the back
of the Knife into the Hub, slightly nudge the Handle
upwards to lock the pins into the Knife Nut.
• PushtheHandlermly(Fig.22),alltheway
into the Hub to engage the pins. Then, turn
the Handle clockwise until it stops. Some
resistance may be experienced when turning.
The Knife is reattached. Lift the Tool up and
out.
Fig. 20
1:00
Fig. 21
Fig. 22
T
H
E
N
T
U
R
N
PUSH FIRST
– 14 –
Ring Guard Cover and Top Knife Cover
Install the Ring Guard Cover on the three Guide Pins (Fig. 23).
Position the Top Knife Cover (Fig. 24) on the lower two Guide Pins and lower the Latch Knob until
the magnet secures the Top Knife Cover in place.
Product Tray
Lower the bottom of the Support Arm onto the Carriage Hinge Pins (Fig. 25).
Tilt the Product Tray toward the Gauge Plate.
Turn the Knob on the Support Arm until it is tight against the Support Arm.
Fig. 23 Fig. 24
Fig. 25
– 15 –
Meat Grip
Assemble the Meat Grip Assembly (Fig. 26) by placing the Washer, Meat Grip Arm, and Meat Grip
Handle on the shaft of the Meat Grip.
Tighten the Handle.
Install the Meat Grip Assembly (Fig. 27) on the Product Tray by sliding the Meat Grip Slide Rod
into the Meat Grip Handle and Product Tray.
Tighten the Meat Grip Slide Rod into the Product Tray.
Lubricate the Meat Grip Slide Rod. See Maintenance.
Sharpener
Install the Sharpener by lowering it back onto
the Sharpener Mount so the Rod and Pin on
thebottomoftheSharpenerttheSlotinthe
Sharpener Mount (Fig. 28).
To use the Sharpener, see Maintenance.
Fig. 26 Fig. 27
MEAT GRIP
MEAT GRIP ARM
MEAT GRIP HANDLE
WASHER
Fig. 28
– 16 –
GASKET INSPECTION
Hobart recommends the manufacturer or an authorized service agent conduct inspections on the entire
slicer a minimum of every 6 months.
The slicer must be removed from service until repaired by the manufacturer or an
authorized service agent if any gasket or seal is found to be damaged or missing.
Fig. 29
– 17 –
MAINTENANCE
Unplug the machine power cord and turn the index knob fully clockwise to close
the gauge plate before doing any maintenance on the slicer.
KNIFE SHARPENING
The CleanCutTM Knife will provide long service in normal food retail or commercial kitchen use.
Sharpen only when necessary. Prolonged or sharpening too frequently results in unnecessary
Knife wear.
Remove the Top Knife Cover by pulling on the Latch
Knob. The Top Knife Cover is held in place with a
strong magnet under the Latch Knob. Remove the
plastic Ring Guard Cover (Fig. 30) by lifting up.
Clean and sanitize the slicer as outlined in the cleaning
section before sharpening the knife. Food debris must
not be allowed to transfer from the Knife to the
Sharpener. Plug in the machine power cord.
Press and hold the KNIFE ON button for 15 seconds
(Fig. 31) while pulling the Sharpener Lever fully forward
(Fig. 31). After 15 seconds, release the Sharpener
Lever and press the OFF button. Unplug the machine
power cord. Clean and sanitize the slicer as outlined
in the cleaning section after sharpening the knife.
Install the plastic Ring Guard Cover and the Top Knife
Cover (Fig. 30).
Fig. 30
Fig. 31
– 18 –
FORM 35284 Rev. F (August 2021) PRINTED IN U.S.A.
LUBRICATION — CARRIAGE SLIDE ROD
Lubricate the Carriage Slide Rod with Lubriplate FMO-
200-AW oil (supplied). Once monthly, apply 4 - 5 drops
directly onto the Carriage Slide Rod on each side of
the Carriage Transport (Fig. 32).
To apply oil, pull out the telescoping tube on the oil
bottle, aim the tube, and squeeze gently on the sides
of the bottle. After applying oil, move the Carriage Tray
back and forth a few times so the oil spreads over the
entire length of the slide rod.
LUBRICATION — MEAT GRIP SLIDE ROD
The Meat Grip Slide Rod can be lubricated periodically
or when any resistance is felt while using the Meat
Grip assembly (Fig. 33). First, wipe the Meat Grip
Slide Rod so the lubrication is applied to a clean, dry
surface. Next, gently squeeze a small amount of the
provided Lubriplate oil on the rod. Then slide the Meat
Grip up and down the rod to restore smooth operation.
SERVICE
ContactyourlocalHobart-authorizedserviceoceforanyrepairsoradjustmentsneededontheslicer.
Fig. 32
Fig. 33
701 S. RIDGE AVENUE
TROY, OHIO 45374-0001
937 332-3000
www.hobartcorp.com
O
DE
D'
EMP
L
OI
M
DOCUMENT 35284 Rév. F (Août 2021)
TRANCHEUSES SÉRIE HS
MODÈLE
Trancheuse manuelle
HS6
HS6N
HS6 (Canada)
HS6N (Canada)
HS8
HS8N
HS8 (Canada)
HS8N (Canada)
Trancheuse automatique
HS7
HS7N
HS7 (Canada)
HS7N (Canada)
HS7 (Japan)
HS7N (Japan)
HS9
HS9N
HS9 (Canada)
HS9N (Canada)
– 2 –
© HOBART, 2019
TABLE DES MATIÈRES
PRÉSENTATION .................................................................................................................................. 3
Caractéristiques ............................................................................................................................... 4
Accessoires et options ..................................................................................................................... 4
INSTALLATION .................................................................................................................................... 5
Déballage ........................................................................................................................................ 5
Connexions électriques ................................................................................................................... 5
Localisation ...................................................................................................................................... 5
Montage ........................................................................................................................................... 5
Nettoyage avant utilisation .............................................................................................................. 5
FONCTIONNEMENT ........................................................................................................................... 6
Tranchage en mode manuel (série HS6 et HS8) ............................................................................. 6
Tranchage en mode manuel (série HS7 et HS9) ............................................................................. 6
Tranchage en mode automatique (série HS7 et HS9) ..................................................................... 7
NETTOYAGE........................................................................................................................................ 8
Nettoyage de la surface et de pièces .............................................................................................. 8
Démontage pour nettoyage ............................................................................................................. 8
Aûteur ...................................................................................................................................... 9
Pousse talon .............................................................................................................................. 9
Plateau ....................................................................................................................................... 9
Cache du couteau et protège lame.......................................................................................... 10
Couteau (amovible – HS6, HS7, HS8 et HS9) ........................................................................ 10
Nettoyage .......................................................................................................................................11
Aûteur .....................................................................................................................................11
Pousse talon .............................................................................................................................11
Plateau ......................................................................................................................................11
Cache du couteau et protège lame...........................................................................................11
Couteau (amovible) ..................................................................................................................11
Couteau (non amovible) ...........................................................................................................11
Sous la trancheuse ...................................................................................................................11
Remontage après nettoyage ......................................................................................................... 12
Couteau (amovible avec extracteur) ........................................................................................ 12
Protège lame et cache du couteau .......................................................................................... 12
Plateau ..................................................................................................................................... 13
Pousse talon ............................................................................................................................ 13
Aûteur .................................................................................................................................... 14
Vérication du joint ........................................................................................................................ 14
ENTRETIEN ....................................................................................................................................... 15
AFFÛTAGE DU COUTEAU ........................................................................................................... 15
LUBRIFICATION — Tige coulissante du chariot ........................................................................... 16
LUBRIFICATION - Tige coulissante du pousse talon .................................................................... 16
RÉPARATION ................................................................................................................................ 16
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36

Hobart HS Series Instructions Manual

Taper
Instructions Manual

dans d''autres langues